Skip to contentSkip to conversation

add PLCA RS support and onsemi NCN26000

PATCH New Piergiorgio Beruto 1 participant 6 messages Jan 9, 2023

Subsystems (8)
lore
Share & tools
lore

Piergiorgio Beruto

author maintainer
#0 lore raw

v3 cover add PLCA RS support and onsemi NCN26000

This patchset adds support for getting/setting the Physical Layer Collision Avoidace (PLCA) Reconciliation Sublayer (RS) configuration and status on Ethernet PHYs that supports it.

PLCA is a feature that provides improved media-access performance in terms of throughput, latency and fairness for multi-drop (P2MP) half-duplex PHYs. PLCA is defined in Clause 148 of the IEEE802.3 specifications as amended by 802.3cg-2019. Currently, PLCA is supported by the 10BASE-T1S single-pair Ethernet PHY defined in the same standard and related amendments. The OPEN Alliance SIG TC14 defines additional specifications for the 10BASE-T1S PHY, including a standard register map for PHYs that embeds the PLCA RS (see PLCA management registers at https://www.opensig.org/about/specifications/).

The changes proposed herein add the appropriate ethtool netlink interface for configuring the PLCA RS on PHYs that supports it. A separate patchset further modifies the ethtool userspace program to show and modify the configuration/status of the PLCA RS.

Additionally, this patchset adds support for the onsemi NCN26000 Industrial Ethernet 10BASE-T1S PHY that uses the newly added PLCA infrastructure.

Piergiorgio Beruto (5):
net/ethtool: add netlink interface for the PLCA RS drivers/net/phy: add the link modes for the 10BASE-T1S Ethernet PHY drivers/net/phy: add connection between ethtool and phylib for PLCA drivers/net/phy: add helpers to get/set PLCA configuration drivers/net/phy: add driver for the onsemi NCN26000 10BASE-T1S PHY

 Documentation/networking/ethtool-netlink.rst | 138 +++++++++
 MAINTAINERS                                  |  14 +
 drivers/net/phy/Kconfig                      |   7 +
 drivers/net/phy/Makefile                     |   1 +
 drivers/net/phy/mdio-open-alliance.h         |  46 +++
 drivers/net/phy/ncn26000.c                   | 171 ++++++++++++
 drivers/net/phy/phy-c45.c                    | 191 +++++++++++++
 drivers/net/phy/phy-core.c                   |   5 +-
 drivers/net/phy/phy.c                        | 192 +++++++++++++
 drivers/net/phy/phy_device.c                 |  17 ++
 drivers/net/phy/phylink.c                    |   6 +-
 include/linux/ethtool.h                      |  12 +
 include/linux/phy.h                          |  84 ++++++
 include/uapi/linux/ethtool.h                 |   3 +
 include/uapi/linux/ethtool_netlink.h         |  25 ++
 net/ethtool/Makefile                         |   2 +-
 net/ethtool/common.c                         |   8 +
 net/ethtool/netlink.c                        |  29 ++
 net/ethtool/netlink.h                        |   6 +
 net/ethtool/plca.c                           | 277 +++++++++++++++++++
 20 files changed, 1231 insertions(+), 3 deletions(-)
 create mode 100644 drivers/net/phy/mdio-open-alliance.h
 create mode 100644 drivers/net/phy/ncn26000.c
 create mode 100644 net/ethtool/plca.c
Signature · 1 line
2.37.4
author maintainer
#1 lore raw

PATCH v3 1/5 net/ethtool: add netlink interface for the PLCA RS

Add support for configuring the PLCA Reconciliation Sublayer on multi-drop PHYs that support IEEE802.3cg-2019 Clause 148 (e.g., 10BASE-T1S). This patch adds the appropriate netlink interface to ethtool.

---
 Documentation/networking/ethtool-netlink.rst | 138 +++++++++
 MAINTAINERS                                  |   6 +
 include/linux/ethtool.h                      |  12 +
 include/linux/phy.h                          |  57 ++++
 include/uapi/linux/ethtool_netlink.h         |  25 ++
 net/ethtool/Makefile                         |   2 +-
 net/ethtool/netlink.c                        |  29 ++
 net/ethtool/netlink.h                        |   6 +
 net/ethtool/plca.c                           | 277 +++++++++++++++++++
 9 files changed, 551 insertions(+), 1 deletion(-)
 create mode 100644 net/ethtool/plca.c
Documentation/networking/ethtool-netlink.rst +138 -0
index f10f8eb44255..c59b542eb693 100644
@@ -1716,6 +1716,141 @@ being used. Current supported options are toeplitz, xor or crc32.
 ETHTOOL_A_RSS_INDIR attribute returns RSS indrection table where each byte
 indicates queue number.
 
+PLCA_GET_CFG
+============
+
+Gets the IEEE 802.3cg-2019 Clause 148 Physical Layer Collision Avoidance
+(PLCA) Reconciliation Sublayer (RS) attributes.
+
+Request contents:
+
+  =====================================  ======  ==========================
+  ``ETHTOOL_A_PLCA_HEADER``              nested  request header
+  =====================================  ======  ==========================
+
+Kernel response contents:
+
+  ======================================  ======  =============================
+  ``ETHTOOL_A_PLCA_HEADER``               nested  reply header
+  ``ETHTOOL_A_PLCA_VERSION``              u16     Supported PLCA management
+                                                  interface standard/version
+  ``ETHTOOL_A_PLCA_ENABLED``              u8      PLCA Admin State
+  ``ETHTOOL_A_PLCA_NODE_ID``              u32     PLCA unique local node ID
+  ``ETHTOOL_A_PLCA_NODE_CNT``             u32     Number of PLCA nodes on the
+                                                  network, including the
+                                                  coordinator
+  ``ETHTOOL_A_PLCA_TO_TMR``               u32     Transmit Opportunity Timer
+                                                  value in bit-times (BT)
+  ``ETHTOOL_A_PLCA_BURST_CNT``            u32     Number of additional packets
+                                                  the node is allowed to send
+                                                  within a single TO
+  ``ETHTOOL_A_PLCA_BURST_TMR``            u32     Time to wait for the MAC to
+                                                  transmit a new frame before
+                                                  terminating the burst
+  ======================================  ======  =============================
+
+When set, the optional ``ETHTOOL_A_PLCA_VERSION`` attribute indicates which
+standard and version the PLCA management interface complies to. When not set,
+the interface is vendor-specific and (possibly) supplied by the driver.
+The OPEN Alliance SIG specifies a standard register map for 10BASE-T1S PHYs
+embedding the PLCA Reconcialiation Sublayer. See "10BASE-T1S PLCA Management
+Registers" at https://www.opensig.org/about/specifications/.
+
+When set, the optional ``ETHTOOL_A_PLCA_ENABLED`` attribute indicates the
+administrative state of the PLCA RS. When not set, the node operates in "plain"
+CSMA/CD mode. This option is corresponding to ``IEEE 802.3cg-2019`` 30.16.1.1.1
+aPLCAAdminState / 30.16.1.2.1 acPLCAAdminControl.
+
+When set, the optional ``ETHTOOL_A_PLCA_NODE_ID`` attribute indicates the
+configured local node ID of the PHY. This ID determines which transmit
+opportunity (TO) is reserved for the node to transmit into. This option is
+corresponding to ``IEEE 802.3cg-2019`` 30.16.1.1.4 aPLCALocalNodeID. The valid
+range for this attribute is [0 .. 255] where 255 means "not configured".
+
+When set, the optional ``ETHTOOL_A_PLCA_NODE_CNT`` attribute indicates the
+configured maximum number of PLCA nodes on the mixing-segment. This number
+determines the total number of transmit opportunities generated during a
+PLCA cycle. This attribute is relevant only for the PLCA coordinator, which is
+the node with aPLCALocalNodeID set to 0. Follower nodes ignore this setting.
+This option is corresponding to ``IEEE 802.3cg-2019`` 30.16.1.1.3
+aPLCANodeCount. The valid range for this attribute is [1 .. 255].
+
+When set, the optional ``ETHTOOL_A_PLCA_TO_TMR`` attribute indicates the
+configured value of the transmit opportunity timer in bit-times. This value
+must be set equal across all nodes sharing the medium for PLCA to work
+correctly. This option is corresponding to ``IEEE 802.3cg-2019`` 30.16.1.1.5
+aPLCATransmitOpportunityTimer. The valid range for this attribute is
+[0 .. 255].
+
+When set, the optional ``ETHTOOL_A_PLCA_BURST_CNT`` attribute indicates the
+configured number of extra packets that the node is allowed to send during a
+single transmit opportunity. By default, this attribute is 0, meaning that
+the node can only send a sigle frame per TO. When greater than 0, the PLCA RS
+keeps the TO after any transmission, waiting for the MAC to send a new frame
+for up to aPLCABurstTimer BTs. This can only happen a number of times per PLCA
+cycle up to the value of this parameter. After that, the burst is over and the
+normal counting of TOs resumes. This option is corresponding to
+``IEEE 802.3cg-2019`` 30.16.1.1.6 aPLCAMaxBurstCount. The valid range for this
+attribute is [0 .. 255].
+
+When set, the optional ``ETHTOOL_A_PLCA_BURST_TMR`` attribute indicates how
+many bit-times the PLCA RS waits for the MAC to initiate a new transmission
+when aPLCAMaxBurstCount is greater than 0. If the MAC fails to send a new
+frame within this time, the burst ends and the counting of TOs resumes.
+Otherwise, the new frame is sent as part of the current burst. This option
+is corresponding to ``IEEE 802.3cg-2019`` 30.16.1.1.7 aPLCABurstTimer. The
+valid range for this attribute is [0 .. 255]. Although, the value should be
+set greater than the Inter-Frame-Gap (IFG) time of the MAC (plus some margin)
+for PLCA burst mode to work as intended.
+
+PLCA_SET_CFG
+============
+
+Sets PLCA RS parameters.
+
+Request contents:
+
+  ======================================  ======  =============================
+  ``ETHTOOL_A_PLCA_HEADER``               nested  request header
+  ``ETHTOOL_A_PLCA_ENABLED``              u8      PLCA Admin State
+  ``ETHTOOL_A_PLCA_NODE_ID``              u8      PLCA unique local node ID
+  ``ETHTOOL_A_PLCA_NODE_CNT``             u8      Number of PLCA nodes on the
+                                                  netkork, including the
+                                                  coordinator
+  ``ETHTOOL_A_PLCA_TO_TMR``               u8      Transmit Opportunity Timer
+                                                  value in bit-times (BT)
+  ``ETHTOOL_A_PLCA_BURST_CNT``            u8      Number of additional packets
+                                                  the node is allowed to send
+                                                  within a single TO
+  ``ETHTOOL_A_PLCA_BURST_TMR``            u8      Time to wait for the MAC to
+                                                  transmit a new frame before
+                                                  terminating the burst
+  ======================================  ======  =============================
+
+For a description of each attribute, see ``PLCA_GET_CFG``.
+
+PLCA_GET_STATUS
+===============
+
+Gets PLCA RS status information.
+
+Request contents:
+
+  =====================================  ======  ==========================
+  ``ETHTOOL_A_PLCA_HEADER``              nested  request header
+  =====================================  ======  ==========================
+
+Kernel response contents:
+
+  ======================================  ======  =============================
+  ``ETHTOOL_A_PLCA_HEADER``               nested  reply header
+  ``ETHTOOL_A_PLCA_STATUS``               u8      PLCA RS operational status
+  ======================================  ======  =============================
+
+When set, the ``ETHTOOL_A_PLCA_STATUS`` attribute indicates whether the node is
+detecting the presence of the BEACON on the network. This flag is
+corresponding to ``IEEE 802.3cg-2019`` 30.16.1.1.2 aPLCAStatus.
+
 Request translation
 ===================
 
@@ -1817,4 +1952,7 @@ are netlink only.
   n/a                                 ``ETHTOOL_MSG_PHC_VCLOCKS_GET``
   n/a                                 ``ETHTOOL_MSG_MODULE_GET``
   n/a                                 ``ETHTOOL_MSG_MODULE_SET``
+  n/a                                 ``ETHTOOL_MSG_PLCA_GET_CFG``
+  n/a                                 ``ETHTOOL_MSG_PLCA_SET_CFG``
+  n/a                                 ``ETHTOOL_MSG_PLCA_GET_STATUS``
   =================================== =====================================
MAINTAINERS +6 -0
index 7f0b7181e60a..8faa15c360e3 100644
@@ -16613,6 +16613,12 @@ S:	Maintained
 F:	Documentation/devicetree/bindings/iio/chemical/plantower,pms7003.yaml
 F:	drivers/iio/chemical/pms7003.c
 
+PLCA RECONCILIATION SUBLAYER (IEEE802.3 Clause 148)
+M:	Piergiorgio Beruto <[email protected]>
+L:	[email protected]
+S:	Maintained
+F:	net/ethtool/plca.c
+
 PLDMFW LIBRARY
 M:	Jacob Keller <[email protected]>
 S:	Maintained
include/linux/ethtool.h +12 -0
index 9e0a76fc7de9..d0da303f6634 100644
@@ -802,12 +802,17 @@ int ethtool_virtdev_set_link_ksettings(struct net_device *dev,
 
 struct phy_device;
 struct phy_tdr_config;
+struct phy_plca_cfg;
+struct phy_plca_status;
 
 /**
  * struct ethtool_phy_ops - Optional PHY device options
  * @get_sset_count: Get number of strings that @get_strings will write.
  * @get_strings: Return a set of strings that describe the requested objects
  * @get_stats: Return extended statistics about the PHY device.
+ * @get_plca_cfg: Return PLCA configuration.
+ * @set_plca_cfg: Set PLCA configuration.
+ * @get_plca_status: Get PLCA configuration.
  * @start_cable_test: Start a cable test
  * @start_cable_test_tdr: Start a Time Domain Reflectometry cable test
  *
@@ -819,6 +824,13 @@ struct ethtool_phy_ops {
 	int (*get_strings)(struct phy_device *dev, u8 *data);
 	int (*get_stats)(struct phy_device *dev,
 			 struct ethtool_stats *stats, u64 *data);
+	int (*get_plca_cfg)(struct phy_device *dev,
+			    struct phy_plca_cfg *plca_cfg);
+	int (*set_plca_cfg)(struct phy_device *dev,
+			    const struct phy_plca_cfg *plca_cfg,
+			    struct netlink_ext_ack *extack);
+	int (*get_plca_status)(struct phy_device *dev,
+			       struct phy_plca_status *plca_st);
 	int (*start_cable_test)(struct phy_device *phydev,
 				struct netlink_ext_ack *extack);
 	int (*start_cable_test_tdr)(struct phy_device *phydev,
include/linux/phy.h +57 -0

63 lines not on this page · raw message

include/uapi/linux/ethtool_netlink.h +25 -0
index 5799a9db034e..75b3d6d476ff 100644
@@ -52,6 +52,9 @@ enum {
 	ETHTOOL_MSG_PSE_GET,
 	ETHTOOL_MSG_PSE_SET,
 	ETHTOOL_MSG_RSS_GET,
+	ETHTOOL_MSG_PLCA_GET_CFG,
+	ETHTOOL_MSG_PLCA_SET_CFG,
+	ETHTOOL_MSG_PLCA_GET_STATUS,
 
 	/* add new constants above here */
 	__ETHTOOL_MSG_USER_CNT,
@@ -99,6 +102,9 @@ enum {
 	ETHTOOL_MSG_MODULE_NTF,
 	ETHTOOL_MSG_PSE_GET_REPLY,
 	ETHTOOL_MSG_RSS_GET_REPLY,
+	ETHTOOL_MSG_PLCA_GET_CFG_REPLY,
+	ETHTOOL_MSG_PLCA_GET_STATUS_REPLY,
+	ETHTOOL_MSG_PLCA_NTF,
 
 	/* add new constants above here */
 	__ETHTOOL_MSG_KERNEL_CNT,
@@ -894,6 +900,25 @@ enum {
 	ETHTOOL_A_RSS_MAX = (__ETHTOOL_A_RSS_CNT - 1),
 };
 
+/* PLCA */
+
+enum {
+	ETHTOOL_A_PLCA_UNSPEC,
+	ETHTOOL_A_PLCA_HEADER,			/* nest - _A_HEADER_* */
+	ETHTOOL_A_PLCA_VERSION,			/* u16 */
+	ETHTOOL_A_PLCA_ENABLED,			/* u8  */
+	ETHTOOL_A_PLCA_STATUS,			/* u8  */
+	ETHTOOL_A_PLCA_NODE_CNT,		/* u32 */
+	ETHTOOL_A_PLCA_NODE_ID,			/* u32 */
+	ETHTOOL_A_PLCA_TO_TMR,			/* u32 */
+	ETHTOOL_A_PLCA_BURST_CNT,		/* u32 */
+	ETHTOOL_A_PLCA_BURST_TMR,		/* u32 */
+
+	/* add new constants above here */
+	__ETHTOOL_A_PLCA_CNT,
+	ETHTOOL_A_PLCA_MAX = (__ETHTOOL_A_PLCA_CNT - 1)
+};
+
 /* generic netlink info */
 #define ETHTOOL_GENL_NAME "ethtool"
 #define ETHTOOL_GENL_VERSION 1
net/ethtool/Makefile +1 -1
index 228f13df2e18..563864c1bf5a 100644
@@ -8,4 +8,4 @@ ethtool_nl-y	:= netlink.o bitset.o strset.o linkinfo.o linkmodes.o rss.o \
 		   linkstate.o debug.o wol.o features.o privflags.o rings.o \
 		   channels.o coalesce.o pause.o eee.o tsinfo.o cabletest.o \
 		   tunnels.o fec.o eeprom.o stats.o phc_vclocks.o module.o \
-		   pse-pd.o
+		   pse-pd.o plca.o
net/ethtool/netlink.c +29 -0
index aee98be6237f..9f924875bba9 100644
@@ -288,6 +288,8 @@ ethnl_default_requests[__ETHTOOL_MSG_USER_CNT] = {
 	[ETHTOOL_MSG_MODULE_GET]	= &ethnl_module_request_ops,
 	[ETHTOOL_MSG_PSE_GET]		= &ethnl_pse_request_ops,
 	[ETHTOOL_MSG_RSS_GET]		= &ethnl_rss_request_ops,
+	[ETHTOOL_MSG_PLCA_GET_CFG]	= &ethnl_plca_cfg_request_ops,
+	[ETHTOOL_MSG_PLCA_GET_STATUS]	= &ethnl_plca_status_request_ops,
 };
 
 static struct ethnl_dump_ctx *ethnl_dump_context(struct netlink_callback *cb)
@@ -603,6 +605,7 @@ ethnl_default_notify_ops[ETHTOOL_MSG_KERNEL_MAX + 1] = {
 	[ETHTOOL_MSG_EEE_NTF]		= &ethnl_eee_request_ops,
 	[ETHTOOL_MSG_FEC_NTF]		= &ethnl_fec_request_ops,
 	[ETHTOOL_MSG_MODULE_NTF]	= &ethnl_module_request_ops,
+	[ETHTOOL_MSG_PLCA_NTF]		= &ethnl_plca_cfg_request_ops,
 };
 
 /* default notification handler */
@@ -696,6 +699,7 @@ static const ethnl_notify_handler_t ethnl_notify_handlers[] = {
 	[ETHTOOL_MSG_EEE_NTF]		= ethnl_default_notify,
 	[ETHTOOL_MSG_FEC_NTF]		= ethnl_default_notify,
 	[ETHTOOL_MSG_MODULE_NTF]	= ethnl_default_notify,
+	[ETHTOOL_MSG_PLCA_NTF]		= ethnl_default_notify,
 };
 
 void ethtool_notify(struct net_device *dev, unsigned int cmd, const void *data)
@@ -1047,6 +1051,31 @@ static const struct genl_ops ethtool_genl_ops[] = {
 		.policy = ethnl_rss_get_policy,
 		.maxattr = ARRAY_SIZE(ethnl_rss_get_policy) - 1,
 	},
+	{
+		.cmd	= ETHTOOL_MSG_PLCA_GET_CFG,
+		.doit	= ethnl_default_doit,
+		.start	= ethnl_default_start,
+		.dumpit	= ethnl_default_dumpit,
+		.done	= ethnl_default_done,
+		.policy = ethnl_plca_get_cfg_policy,
+		.maxattr = ARRAY_SIZE(ethnl_plca_get_cfg_policy) - 1,
+	},
+	{
+		.cmd	= ETHTOOL_MSG_PLCA_SET_CFG,
+		.flags	= GENL_UNS_ADMIN_PERM,
+		.doit	= ethnl_set_plca_cfg,
+		.policy = ethnl_plca_set_cfg_policy,
+		.maxattr = ARRAY_SIZE(ethnl_plca_set_cfg_policy) - 1,
+	},
+	{
+		.cmd	= ETHTOOL_MSG_PLCA_GET_STATUS,
+		.doit	= ethnl_default_doit,
+		.start	= ethnl_default_start,
+		.dumpit	= ethnl_default_dumpit,
+		.done	= ethnl_default_done,
+		.policy = ethnl_plca_get_status_policy,
+		.maxattr = ARRAY_SIZE(ethnl_plca_get_status_policy) - 1,
+	},
 };
 
 static const struct genl_multicast_group ethtool_nl_mcgrps[] = {
net/ethtool/netlink.h +6 -0
index 3753787ba233..f271266f6e28 100644
@@ -347,6 +347,8 @@ extern const struct ethnl_request_ops ethnl_phc_vclocks_request_ops;
 extern const struct ethnl_request_ops ethnl_module_request_ops;
 extern const struct ethnl_request_ops ethnl_pse_request_ops;
 extern const struct ethnl_request_ops ethnl_rss_request_ops;
+extern const struct ethnl_request_ops ethnl_plca_cfg_request_ops;
+extern const struct ethnl_request_ops ethnl_plca_status_request_ops;
 
 extern const struct nla_policy ethnl_header_policy[ETHTOOL_A_HEADER_FLAGS + 1];
 extern const struct nla_policy ethnl_header_policy_stats[ETHTOOL_A_HEADER_FLAGS + 1];
@@ -388,6 +390,9 @@ extern const struct nla_policy ethnl_module_set_policy[ETHTOOL_A_MODULE_POWER_MO
 extern const struct nla_policy ethnl_pse_get_policy[ETHTOOL_A_PSE_HEADER + 1];
 extern const struct nla_policy ethnl_pse_set_policy[ETHTOOL_A_PSE_MAX + 1];
 extern const struct nla_policy ethnl_rss_get_policy[ETHTOOL_A_RSS_CONTEXT + 1];
+extern const struct nla_policy ethnl_plca_get_cfg_policy[ETHTOOL_A_PLCA_HEADER + 1];
+extern const struct nla_policy ethnl_plca_set_cfg_policy[ETHTOOL_A_PLCA_MAX + 1];
+extern const struct nla_policy ethnl_plca_get_status_policy[ETHTOOL_A_PLCA_HEADER + 1];
 
 int ethnl_set_linkinfo(struct sk_buff *skb, struct genl_info *info);
 int ethnl_set_linkmodes(struct sk_buff *skb, struct genl_info *info);
@@ -408,6 +413,7 @@ int ethnl_tunnel_info_dumpit(struct sk_buff *skb, struct netlink_callback *cb);
 int ethnl_set_fec(struct sk_buff *skb, struct genl_info *info);
 int ethnl_set_module(struct sk_buff *skb, struct genl_info *info);
 int ethnl_set_pse(struct sk_buff *skb, struct genl_info *info);
+int ethnl_set_plca_cfg(struct sk_buff *skb, struct genl_info *info);
 
 extern const char stats_std_names[__ETHTOOL_STATS_CNT][ETH_GSTRING_LEN];
 extern const char stats_eth_phy_names[__ETHTOOL_A_STATS_ETH_PHY_CNT][ETH_GSTRING_LEN];
net/ethtool/plca.c new file +277 -0

277 lines not on this page · raw message

Signature · 1 line
2.37.4
author maintainer
#2 lore raw

PATCH v3 2/5 drivers/net/phy: add the link modes for the 10BASE-T1S Ethernet PHY

In reply to Piergiorgio Beruto

This patch adds the link modes for the IEEE 802.3cg Clause 147 10BASE-T1S Ethernet PHY. According to the specifications, the 10BASE-T1S supports Point-To-Point Full-Duplex, Point-To-Point Half-Duplex and/or Point-To-Multipoint (AKA Multi-Drop) Half-Duplex operations.

---
 drivers/net/phy/phy-core.c   |  5 ++++-
 drivers/net/phy/phy_device.c | 14 ++++++++++++++
 drivers/net/phy/phylink.c    |  6 +++++-
 include/linux/phy.h          | 14 ++++++++++++++
 include/uapi/linux/ethtool.h |  3 +++
 net/ethtool/common.c         |  8 ++++++++
 6 files changed, 48 insertions(+), 2 deletions(-)
drivers/net/phy/phy-core.c +4 -1
index 5d08c627a516..a64186dc53f8 100644
@@ -13,7 +13,7 @@
  */
 const char *phy_speed_to_str(int speed)
 {
-	BUILD_BUG_ON_MSG(__ETHTOOL_LINK_MODE_MASK_NBITS != 99,
+	BUILD_BUG_ON_MSG(__ETHTOOL_LINK_MODE_MASK_NBITS != 102,
 		"Enum ethtool_link_mode_bit_indices and phylib are out of sync. "
 		"If a speed or mode has been added please update phy_speed_to_str "
 		"and the PHY settings array.\n");
@@ -260,6 +260,9 @@ static const struct phy_setting settings[] = {
 	PHY_SETTING(     10, FULL,     10baseT_Full		),
 	PHY_SETTING(     10, HALF,     10baseT_Half		),
 	PHY_SETTING(     10, FULL,     10baseT1L_Full		),
+	PHY_SETTING(     10, FULL,     10baseT1S_Full		),
+	PHY_SETTING(     10, HALF,     10baseT1S_Half		),
+	PHY_SETTING(     10, HALF,     10baseT1S_P2MP_Half	),
 };
 #undef PHY_SETTING
 
drivers/net/phy/phy_device.c +14 -0
index 716870a4499c..8e48b3cec5e7 100644
@@ -45,6 +45,9 @@ EXPORT_SYMBOL_GPL(phy_basic_features);
 __ETHTOOL_DECLARE_LINK_MODE_MASK(phy_basic_t1_features) __ro_after_init;
 EXPORT_SYMBOL_GPL(phy_basic_t1_features);
 
+__ETHTOOL_DECLARE_LINK_MODE_MASK(phy_basic_t1s_p2mp_features) __ro_after_init;
+EXPORT_SYMBOL_GPL(phy_basic_t1s_p2mp_features);
+
 __ETHTOOL_DECLARE_LINK_MODE_MASK(phy_gbit_features) __ro_after_init;
 EXPORT_SYMBOL_GPL(phy_gbit_features);
 
@@ -98,6 +101,12 @@ const int phy_basic_t1_features_array[3] = {
 };
 EXPORT_SYMBOL_GPL(phy_basic_t1_features_array);
 
+const int phy_basic_t1s_p2mp_features_array[2] = {
+	ETHTOOL_LINK_MODE_TP_BIT,
+	ETHTOOL_LINK_MODE_10baseT1S_P2MP_Half_BIT,
+};
+EXPORT_SYMBOL_GPL(phy_basic_t1s_p2mp_features_array);
+
 const int phy_gbit_features_array[2] = {
 	ETHTOOL_LINK_MODE_1000baseT_Half_BIT,
 	ETHTOOL_LINK_MODE_1000baseT_Full_BIT,
@@ -138,6 +147,11 @@ static void features_init(void)
 			       ARRAY_SIZE(phy_basic_t1_features_array),
 			       phy_basic_t1_features);
 
+	/* 10 half, P2MP, TP */
+	linkmode_set_bit_array(phy_basic_t1s_p2mp_features_array,
+			       ARRAY_SIZE(phy_basic_t1s_p2mp_features_array),
+			       phy_basic_t1s_p2mp_features);
+
 	/* 10/100 half/full + 1000 half/full */
 	linkmode_set_bit_array(phy_basic_ports_array,
 			       ARRAY_SIZE(phy_basic_ports_array),
drivers/net/phy/phylink.c +5 -1
index 09cc65c0da93..319790221d7f 100644
@@ -241,12 +241,16 @@ void phylink_caps_to_linkmodes(unsigned long *linkmodes, unsigned long caps)
 	if (caps & MAC_ASYM_PAUSE)
 		__set_bit(ETHTOOL_LINK_MODE_Asym_Pause_BIT, linkmodes);
 
-	if (caps & MAC_10HD)
+	if (caps & MAC_10HD) {
 		__set_bit(ETHTOOL_LINK_MODE_10baseT_Half_BIT, linkmodes);
+		__set_bit(ETHTOOL_LINK_MODE_10baseT1S_Half_BIT, linkmodes);
+		__set_bit(ETHTOOL_LINK_MODE_10baseT1S_P2MP_Half_BIT, linkmodes);
+	}
 
 	if (caps & MAC_10FD) {
 		__set_bit(ETHTOOL_LINK_MODE_10baseT_Full_BIT, linkmodes);
 		__set_bit(ETHTOOL_LINK_MODE_10baseT1L_Full_BIT, linkmodes);
+		__set_bit(ETHTOOL_LINK_MODE_10baseT1S_Full_BIT, linkmodes);
 	}
 
 	if (caps & MAC_100HD) {
include/linux/phy.h +14 -0
index c2c04b989cc2..1e87d3f05209 100644
@@ -45,6 +45,7 @@
 
 extern __ETHTOOL_DECLARE_LINK_MODE_MASK(phy_basic_features) __ro_after_init;
 extern __ETHTOOL_DECLARE_LINK_MODE_MASK(phy_basic_t1_features) __ro_after_init;
+extern __ETHTOOL_DECLARE_LINK_MODE_MASK(phy_basic_t1s_p2mp_features) __ro_after_init;
 extern __ETHTOOL_DECLARE_LINK_MODE_MASK(phy_gbit_features) __ro_after_init;
 extern __ETHTOOL_DECLARE_LINK_MODE_MASK(phy_gbit_fibre_features) __ro_after_init;
 extern __ETHTOOL_DECLARE_LINK_MODE_MASK(phy_gbit_all_ports_features) __ro_after_init;
@@ -54,6 +55,7 @@ extern __ETHTOOL_DECLARE_LINK_MODE_MASK(phy_10gbit_full_features) __ro_after_ini
 
 #define PHY_BASIC_FEATURES ((unsigned long *)&phy_basic_features)
 #define PHY_BASIC_T1_FEATURES ((unsigned long *)&phy_basic_t1_features)
+#define PHY_BASIC_T1S_P2MP_FEATURES ((unsigned long *)&phy_basic_t1s_p2mp_features)
 #define PHY_GBIT_FEATURES ((unsigned long *)&phy_gbit_features)
 #define PHY_GBIT_FIBRE_FEATURES ((unsigned long *)&phy_gbit_fibre_features)
 #define PHY_GBIT_ALL_PORTS_FEATURES ((unsigned long *)&phy_gbit_all_ports_features)
@@ -66,6 +68,7 @@ extern const int phy_fibre_port_array[1];
 extern const int phy_all_ports_features_array[7];
 extern const int phy_10_100_features_array[4];
 extern const int phy_basic_t1_features_array[3];
+extern const int phy_basic_t1s_p2mp_features_array[2];
 extern const int phy_gbit_features_array[2];
 extern const int phy_10gbit_features_array[1];
 
@@ -1036,6 +1039,17 @@ struct phy_driver {
 	int (*get_sqi)(struct phy_device *dev);
 	/** @get_sqi_max: Get the maximum signal quality indication */
 	int (*get_sqi_max)(struct phy_device *dev);
+
+	/* PLCA RS interface */
+	/** @get_plca_cfg: Return the current PLCA configuration */
+	int (*get_plca_cfg)(struct phy_device *dev,
+			    struct phy_plca_cfg *plca_cfg);
+	/** @set_plca_cfg: Set the PLCA configuration */
+	int (*set_plca_cfg)(struct phy_device *dev,
+			    const struct phy_plca_cfg *plca_cfg);
+	/** @get_plca_status: Return the current PLCA status info */
+	int (*get_plca_status)(struct phy_device *dev,
+			       struct phy_plca_status *plca_st);
 };
 #define to_phy_driver(d) container_of(to_mdio_common_driver(d),		\
 				      struct phy_driver, mdiodrv)
include/uapi/linux/ethtool.h +3 -0
index 58e587ba0450..5f414deacf23 100644
@@ -1741,6 +1741,9 @@ enum ethtool_link_mode_bit_indices {
 	ETHTOOL_LINK_MODE_800000baseDR8_2_Full_BIT	 = 96,
 	ETHTOOL_LINK_MODE_800000baseSR8_Full_BIT	 = 97,
 	ETHTOOL_LINK_MODE_800000baseVR8_Full_BIT	 = 98,
+	ETHTOOL_LINK_MODE_10baseT1S_Full_BIT		 = 99,
+	ETHTOOL_LINK_MODE_10baseT1S_Half_BIT		 = 100,
+	ETHTOOL_LINK_MODE_10baseT1S_P2MP_Half_BIT	 = 101,
 
 	/* must be last entry */
 	__ETHTOOL_LINK_MODE_MASK_NBITS
net/ethtool/common.c +8 -0
index 6f399afc2ff2..5fb19050991e 100644
@@ -208,6 +208,9 @@ const char link_mode_names[][ETH_GSTRING_LEN] = {
 	__DEFINE_LINK_MODE_NAME(800000, DR8_2, Full),
 	__DEFINE_LINK_MODE_NAME(800000, SR8, Full),
 	__DEFINE_LINK_MODE_NAME(800000, VR8, Full),
+	__DEFINE_LINK_MODE_NAME(10, T1S, Full),
+	__DEFINE_LINK_MODE_NAME(10, T1S, Half),
+	__DEFINE_LINK_MODE_NAME(10, T1S_P2MP, Half),
 };
 static_assert(ARRAY_SIZE(link_mode_names) == __ETHTOOL_LINK_MODE_MASK_NBITS);
 
@@ -244,6 +247,8 @@ static_assert(ARRAY_SIZE(link_mode_names) == __ETHTOOL_LINK_MODE_MASK_NBITS);
 #define __LINK_MODE_LANES_X		1
 #define __LINK_MODE_LANES_FX		1
 #define __LINK_MODE_LANES_T1L		1
+#define __LINK_MODE_LANES_T1S		1
+#define __LINK_MODE_LANES_T1S_P2MP	1
 #define __LINK_MODE_LANES_VR8		8
 #define __LINK_MODE_LANES_DR8_2		8
 
@@ -366,6 +371,9 @@ const struct link_mode_info link_mode_params[] = {
 	__DEFINE_LINK_MODE_PARAMS(800000, DR8_2, Full),
 	__DEFINE_LINK_MODE_PARAMS(800000, SR8, Full),
 	__DEFINE_LINK_MODE_PARAMS(800000, VR8, Full),
+	__DEFINE_LINK_MODE_PARAMS(10, T1S, Full),
+	__DEFINE_LINK_MODE_PARAMS(10, T1S, Half),
+	__DEFINE_LINK_MODE_PARAMS(10, T1S_P2MP, Half),
 };
 static_assert(ARRAY_SIZE(link_mode_params) == __ETHTOOL_LINK_MODE_MASK_NBITS);
 
Signature · 1 line
2.37.4
author maintainer
#3 lore raw

PATCH v3 3/5 drivers/net/phy: add connection between ethtool and phylib for PLCA

In reply to Piergiorgio Beruto

This patch adds the required connection between netlink ethtool and phylib to resolve PLCA get/set config and get status messages.

---
 drivers/net/phy/phy.c        | 192 +++++++++++++++++++++++++++++++++++
 drivers/net/phy/phy_device.c |   3 +
 include/linux/phy.h          |   7 ++
 3 files changed, 202 insertions(+)
drivers/net/phy/phy.c +192 -0
index e5b6cb1a77f9..3378ca4f49b6 100644
@@ -543,6 +543,198 @@ int phy_ethtool_get_stats(struct phy_device *phydev,
 }
 EXPORT_SYMBOL(phy_ethtool_get_stats);
 
+/**
+ * phy_ethtool_get_plca_cfg - Get PLCA RS configuration
+ * @phydev: the phy_device struct
+ * @plca_cfg: where to store the retrieved configuration
+ *
+ * Retrieve the PLCA configuration from the PHY. Return 0 on success or a
+ * negative value if an error occurred.
+ */
+int phy_ethtool_get_plca_cfg(struct phy_device *phydev,
+			     struct phy_plca_cfg *plca_cfg)
+{
+	int ret;
+
+	if (!phydev->drv) {
+		ret = -EIO;
+		goto out;
+	}
+
+	if (!phydev->drv->get_plca_cfg) {
+		ret = -EOPNOTSUPP;
+		goto out;
+	}
+
+	mutex_lock(&phydev->lock);
+	ret = phydev->drv->get_plca_cfg(phydev, plca_cfg);
+
+	mutex_unlock(&phydev->lock);
+out:
+	return ret;
+}
+
+/**
+ * plca_check_valid - Check PLCA configuration before enabling
+ * @phydev: the phy_device struct
+ * @plca_cfg: current PLCA configuration
+ * @extack: extack for reporting useful error messages
+ *
+ * Checks whether the PLCA and PHY configuration are consistent and it is safe
+ * to enable PLCA. Returns 0 on success or a negative value if the PLCA or PHY
+ * configuration is not consistent.
+ */
+static int plca_check_valid(struct phy_device *phydev,
+			    const struct phy_plca_cfg *plca_cfg,
+			    struct netlink_ext_ack *extack)
+{
+	int ret = 0;
+
+	if (!linkmode_test_bit(ETHTOOL_LINK_MODE_10baseT1S_P2MP_Half_BIT,
+			       phydev->advertising)) {
+		ret = -EOPNOTSUPP;
+		NL_SET_ERR_MSG(extack,
+			       "Point to Multi-Point mode is not enabled");
+	} else if (plca_cfg->node_id >= 255) {
+		NL_SET_ERR_MSG(extack, "PLCA node ID is not set");
+		ret = -EINVAL;
+	}
+
+	return ret;
+}
+
+/**
+ * phy_ethtool_set_plca_cfg - Set PLCA RS configuration
+ * @phydev: the phy_device struct
+ * @plca_cfg: new PLCA configuration to apply
+ * @extack: extack for reporting useful error messages
+ *
+ * Sets the PLCA configuration in the PHY. Return 0 on success or a
+ * negative value if an error occurred.
+ */
+int phy_ethtool_set_plca_cfg(struct phy_device *phydev,
+			     const struct phy_plca_cfg *plca_cfg,
+			     struct netlink_ext_ack *extack)
+{
+	struct phy_plca_cfg *curr_plca_cfg;
+	int ret;
+
+	if (!phydev->drv) {
+		ret = -EIO;
+		goto out;
+	}
+
+	if (!phydev->drv->set_plca_cfg ||
+	    !phydev->drv->get_plca_cfg) {
+		ret = -EOPNOTSUPP;
+		goto out;
+	}
+
+	curr_plca_cfg = kmalloc(sizeof(*curr_plca_cfg), GFP_KERNEL);
+	if (!curr_plca_cfg) {
+		ret = -ENOMEM;
+		goto out;
+	}
+
+	mutex_lock(&phydev->lock);
+
+	ret = phydev->drv->get_plca_cfg(phydev, curr_plca_cfg);
+	if (ret)
+		goto out_drv;
+
+	if (curr_plca_cfg->enabled < 0 && plca_cfg->enabled >= 0) {
+		NL_SET_ERR_MSG(extack,
+			       "PHY does not support changing the PLCA 'enable' attribute");
+		ret = -EINVAL;
+		goto out_drv;
+	}
+
+	if (curr_plca_cfg->node_id < 0 && plca_cfg->node_id >= 0) {
+		NL_SET_ERR_MSG(extack,
+			       "PHY does not support changing the PLCA 'local node ID' attribute");
+		ret = -EINVAL;
+		goto out_drv;
+	}
+
+	if (curr_plca_cfg->node_cnt < 0 && plca_cfg->node_cnt >= 0) {
+		NL_SET_ERR_MSG(extack,
+			       "PHY does not support changing the PLCA 'node count' attribute");
+		ret = -EINVAL;
+		goto out_drv;
+	}
+
+	if (curr_plca_cfg->to_tmr < 0 && plca_cfg->to_tmr >= 0) {
+		NL_SET_ERR_MSG(extack,
+			       "PHY does not support changing the PLCA 'TO timer' attribute");
+		ret = -EINVAL;
+		goto out_drv;
+	}
+
+	if (curr_plca_cfg->burst_cnt < 0 && plca_cfg->burst_cnt >= 0) {
+		NL_SET_ERR_MSG(extack,
+			       "PHY does not support changing the PLCA 'burst count' attribute");
+		ret = -EINVAL;
+		goto out_drv;
+	}
+
+	if (curr_plca_cfg->burst_tmr < 0 && plca_cfg->burst_tmr >= 0) {
+		NL_SET_ERR_MSG(extack,
+			       "PHY does not support changing the PLCA 'burst timer' attribute");
+		ret = -EINVAL;
+		goto out_drv;
+	}
+
+	// if enabling PLCA, perform a few sanity checks
+	if (plca_cfg->enabled > 0) {
+		// allow setting node_id concurrently with enabled
+		if (plca_cfg->node_id >= 0)
+			curr_plca_cfg->node_id = plca_cfg->node_id;
+
+		ret = plca_check_valid(phydev, curr_plca_cfg, extack);
+		if (ret)
+			goto out_drv;
+	}
+
+	ret = phydev->drv->set_plca_cfg(phydev, plca_cfg);
+
+out_drv:
+	kfree(curr_plca_cfg);
+	mutex_unlock(&phydev->lock);
+out:
+	return ret;
+}
+
+/**
+ * phy_ethtool_get_plca_status - Get PLCA RS status information
+ * @phydev: the phy_device struct
+ * @plca_st: where to store the retrieved status information
+ *
+ * Retrieve the PLCA status information from the PHY. Return 0 on success or a
+ * negative value if an error occurred.
+ */
+int phy_ethtool_get_plca_status(struct phy_device *phydev,
+				struct phy_plca_status *plca_st)
+{
+	int ret;
+
+	if (!phydev->drv) {
+		ret = -EIO;
+		goto out;
+	}
+
+	if (!phydev->drv->get_plca_status) {
+		ret = -EOPNOTSUPP;
+		goto out;
+	}
+
+	mutex_lock(&phydev->lock);
+	ret = phydev->drv->get_plca_status(phydev, plca_st);
+
+	mutex_unlock(&phydev->lock);
+out:
+	return ret;
+}
+
 /**
  * phy_start_cable_test - Start a cable test
  *
drivers/net/phy/phy_device.c +3 -0
index 8e48b3cec5e7..44bd06be9691 100644
@@ -3276,6 +3276,9 @@ static const struct ethtool_phy_ops phy_ethtool_phy_ops = {
 	.get_sset_count		= phy_ethtool_get_sset_count,
 	.get_strings		= phy_ethtool_get_strings,
 	.get_stats		= phy_ethtool_get_stats,
+	.get_plca_cfg		= phy_ethtool_get_plca_cfg,
+	.set_plca_cfg		= phy_ethtool_set_plca_cfg,
+	.get_plca_status	= phy_ethtool_get_plca_status,
 	.start_cable_test	= phy_start_cable_test,
 	.start_cable_test_tdr	= phy_start_cable_test_tdr,
 };
include/linux/phy.h +7 -0
index 1e87d3f05209..bcaf1dfd0687 100644
@@ -1846,6 +1846,13 @@ int phy_ethtool_get_strings(struct phy_device *phydev, u8 *data);
 int phy_ethtool_get_sset_count(struct phy_device *phydev);
 int phy_ethtool_get_stats(struct phy_device *phydev,
 			  struct ethtool_stats *stats, u64 *data);
+int phy_ethtool_get_plca_cfg(struct phy_device *phydev,
+			     struct phy_plca_cfg *plca_cfg);
+int phy_ethtool_set_plca_cfg(struct phy_device *phydev,
+			     const struct phy_plca_cfg *plca_cfg,
+			     struct netlink_ext_ack *extack);
+int phy_ethtool_get_plca_status(struct phy_device *phydev,
+				struct phy_plca_status *plca_st);
 
 static inline int phy_package_read(struct phy_device *phydev, u32 regnum)
 {
Signature · 1 line
2.37.4
author maintainer
#4 lore raw

PATCH v3 4/5 drivers/net/phy: add helpers to get/set PLCA configuration

In reply to Piergiorgio Beruto

This patch adds support in phylib to read/write PLCA configuration for Ethernet PHYs that support the OPEN Alliance "10BASE-T1S PLCA Management Registers" specifications. These can be found at
https://www.opensig.org/about/specifications/

---
 MAINTAINERS                          |   1 +
 drivers/net/phy/mdio-open-alliance.h |  46 +++++++
 drivers/net/phy/phy-c45.c            | 191 +++++++++++++++++++++++++++
 include/linux/phy.h                  |   6 +
 4 files changed, 244 insertions(+)
 create mode 100644 drivers/net/phy/mdio-open-alliance.h
MAINTAINERS +1 -0
index 8faa15c360e3..4356382ad57c 100644
@@ -16617,6 +16617,7 @@ PLCA RECONCILIATION SUBLAYER (IEEE802.3 Clause 148)
 M:	Piergiorgio Beruto <[email protected]>
 L:	[email protected]
 S:	Maintained
+F:	drivers/net/phy/mdio-open-alliance.h
 F:	net/ethtool/plca.c
 
 PLDMFW LIBRARY
drivers/net/phy/mdio-open-alliance.h new file +46 -0

46 lines not on this page · raw message

drivers/net/phy/phy-c45.c +191 -0

203 lines not on this page · raw message

include/linux/phy.h +6 -0
index bcaf1dfd0687..23aa23cde940 100644
@@ -1748,6 +1748,12 @@ int genphy_c45_loopback(struct phy_device *phydev, bool enable);
 int genphy_c45_pma_resume(struct phy_device *phydev);
 int genphy_c45_pma_suspend(struct phy_device *phydev);
 int genphy_c45_fast_retrain(struct phy_device *phydev, bool enable);
+int genphy_c45_plca_get_cfg(struct phy_device *phydev,
+			    struct phy_plca_cfg *plca_cfg);
+int genphy_c45_plca_set_cfg(struct phy_device *phydev,
+			    const struct phy_plca_cfg *plca_cfg);
+int genphy_c45_plca_get_status(struct phy_device *phydev,
+			       struct phy_plca_status *plca_st);
 
 /* Generic C45 PHY driver */
 extern struct phy_driver genphy_c45_driver;
Signature · 1 line
2.37.4
author maintainer
#5 lore raw

PATCH v3 5/5 drivers/net/phy: add driver for the onsemi NCN26000 10BASE-T1S PHY

In reply to Piergiorgio Beruto

This patch adds support for the onsemi NCN26000 10BASE-T1S industrial Ethernet PHY. The driver supports Point-to-Multipoint operation without auto-negotiation and with link control handling. The PHY also features PLCA for improving performance in P2MP mode.

---
 MAINTAINERS                |   7 ++
 drivers/net/phy/Kconfig    |   7 ++
 drivers/net/phy/Makefile   |   1 +
 drivers/net/phy/ncn26000.c | 171 +++++++++++++++++++++++++++++++++++++
 4 files changed, 186 insertions(+)
 create mode 100644 drivers/net/phy/ncn26000.c
MAINTAINERS +7 -0
index 4356382ad57c..c1dadb34009d 100644
@@ -15581,6 +15581,13 @@ L:	[email protected]
 S:	Maintained
 F:	arch/mips/boot/dts/ralink/omega2p.dts
 
+ONSEMI ETHERNET PHY DRIVERS
+M:	Piergiorgio Beruto <[email protected]>
+L:	[email protected]
+S:	Supported
+W:	http://www.onsemi.com
+F:	drivers/net/phy/ncn*
+
 OP-TEE DRIVER
 M:	Jens Wiklander <[email protected]>
 L:	[email protected]
drivers/net/phy/Kconfig +7 -0
index 1327290decab..7eee2beb3475 100644
@@ -277,6 +277,13 @@ config NXP_TJA11XX_PHY
 	help
 	  Currently supports the NXP TJA1100 and TJA1101 PHY.
 
+config NCN26000_PHY
+	tristate "onsemi 10BASE-T1S Ethernet PHY"
+	help
+	  Adds support for the onsemi 10BASE-T1S Ethernet PHY.
+	  Currently supports the NCN26000 10BASE-T1S Industrial PHY
+	  with MII interface.
+
 config AT803X_PHY
 	tristate "Qualcomm Atheros AR803X PHYs and QCA833x PHYs"
 	depends on REGULATOR
drivers/net/phy/Makefile +1 -0
index f7138d3c896b..b5138066ba04 100644
@@ -77,6 +77,7 @@ obj-$(CONFIG_MICROCHIP_T1_PHY)	+= microchip_t1.o
 obj-$(CONFIG_MICROSEMI_PHY)	+= mscc/
 obj-$(CONFIG_MOTORCOMM_PHY)	+= motorcomm.o
 obj-$(CONFIG_NATIONAL_PHY)	+= national.o
+obj-$(CONFIG_NCN26000_PHY)	+= ncn26000.o
 obj-$(CONFIG_NXP_C45_TJA11XX_PHY)	+= nxp-c45-tja11xx.o
 obj-$(CONFIG_NXP_TJA11XX_PHY)	+= nxp-tja11xx.o
 obj-$(CONFIG_QSEMI_PHY)		+= qsemi.o
drivers/net/phy/ncn26000.c new file +171 -0

171 lines not on this page · raw message

Signature · 1 line
2.37.4