Skip to contentSkip to conversation

arm64: dts: Add IOT2050 M.2 board, describe QSPI layout

PATCH In review Jan Kiszka 2 participants 5 messages Jan 19, 2023 – Jan 25, 2023

Subsystems (2)
lore
Share & tools
lore

Jan Kiszka

author
#0 lore raw

v2 cover arm64: dts: Add IOT2050 M.2 board, describe QSPI layout

This adds the devices tree for a new variant of the IOT2050 which comes with two M.2 slots and is otherwise almost equivalent to the existing Advanced PG2 variant (USB3 is available via M.2 now).

Furthermore, the device tree of the whole device series is extended to also hold the QSPI layout.

Changes in v2:
- alphabetic ordering in binding schema and makefile
- dropped an unneeded blank line in patch 3

Jan

Jan Kiszka (2):
arm64: dts: ti: iot2050: Add layout of OSPI flash
dt-bindings: arm: ti: Add binding for Siemens IOT2050 M.2 variant

chao zeng (1):
arm64: dts: ti: iot2050: Add support for M.2 variant

 .../devicetree/bindings/arm/ti/k3.yaml        |   1 +
 arch/arm64/boot/dts/ti/Makefile               |   3 +
 .../boot/dts/ti/k3-am65-iot2050-common.dtsi   |  46 +++++++
 .../dts/ti/k3-am6548-iot2050-advanced-m2.dts  | 121 ++++++++++++++++++
 4 files changed, 171 insertions(+)
 create mode 100644 arch/arm64/boot/dts/ti/k3-am6548-iot2050-advanced-m2.dts
Signature · 7 lines
2.35.3


_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
author
#1 lore raw

PATCH v2 1/3 arm64: dts: ti: iot2050: Add layout of OSPI flash

From: Jan Kiszka <[email protected]>

Describe the layout of the OSPI flash as the latest firmware uses it. Specifically the location of the U-Boot envs is important for userspace in order to access it.

---
 .../boot/dts/ti/k3-am65-iot2050-common.dtsi   | 46 +++++++++++++++++++
 1 file changed, 46 insertions(+)
arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi +46 -0
index 3cced26b520a..96ac2b476b11 100644
@@ -609,6 +609,52 @@ flash@0 {
 		cdns,tchsh-ns = <60>;
 		cdns,tslch-ns = <60>;
 		cdns,read-delay = <2>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			seboot@0 {
+				label = "seboot";
+				reg = <0x0 0x180000>; /* 1.5M */
+			};
+
+			tispl@180000 {
+				label = "tispl";
+				reg = <0x180000 0x200000>; /* 2M */
+			};
+
+			u-boot@380000 {
+				label = "u-boot";
+				reg = <0x380000 0x300000>; /* 3M */
+			};
+
+			env@680000 {
+				label = "env";
+				reg = <0x680000 0x20000>; /* 128K */
+			};
+
+			env-backup@6a0000 {
+				label = "env.backup";
+				reg = <0x6a0000 0x20000>; /* 128K */
+			};
+
+			otpcmd@6c0000 {
+				label = "otpcmd";
+				reg = <0x6c0000 0x10000>; /* 64K */
+			};
+
+			unused@6d0000 {
+				label = "unused";
+				reg = <0x6d0000 0x7b0000>; /* 7872K */
+			};
+
+			seboot-backup@e80000 {
+				label = "seboot.backup";
+				reg = <0xe80000 0x180000>; /* 1.5M */
+			};
+		};
 	};
 };
 
Signature · 7 lines
2.35.3


_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
author
#2 lore raw

PATCH v2 2/3 dt-bindings: arm: ti: Add binding for Siemens IOT2050 M.2 variant

In reply to Jan Kiszka

From: Jan Kiszka <[email protected]>

This new variant is derived from the Advanced PG2 board, replacing the MiniPCI slot with B and E-keyed M.2 slots.

---
 Documentation/devicetree/bindings/arm/ti/k3.yaml | 1 +
 1 file changed, 1 insertion(+)
Documentation/devicetree/bindings/arm/ti/k3.yaml +1 -0
index 203faab80142..0ed4e973753f 100644
@@ -42,6 +42,7 @@ properties:
         items:
           - enum:
               - siemens,iot2050-advanced
+              - siemens,iot2050-advanced-m2
               - siemens,iot2050-advanced-pg2
               - siemens,iot2050-basic
               - siemens,iot2050-basic-pg2
Signature · 7 lines
2.35.3


_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
author
#3 lore raw

PATCH v2 3/3 arm64: dts: ti: iot2050: Add support for M.2 variant

In reply to Jan Kiszka

From: chao zeng <[email protected]>

The M.2 variant comes with 2 slots, one B-keyed and another one E-keyed. They are configured by the firmware during startup. Also the device tree will be adjusted according to the detect or manually configured interface mode by the firmware. The kernel only carries a single configuration as base device tree. It has to be built with a symbols node so that the firmware can apply overlays for the connector modes.

[Jan: refactored to a single DT]
---
 arch/arm64/boot/dts/ti/Makefile               |   3 +
 .../dts/ti/k3-am6548-iot2050-advanced-m2.dts  | 121 ++++++++++++++++++
 2 files changed, 124 insertions(+)
 create mode 100644 arch/arm64/boot/dts/ti/k3-am6548-iot2050-advanced-m2.dts
arch/arm64/boot/dts/ti/Makefile +3 -0
index cf7c509538a4..bfb16b62c58d 100644
@@ -10,8 +10,11 @@ dtb-$(CONFIG_ARCH_K3) += k3-am654-base-board.dtb
 dtb-$(CONFIG_ARCH_K3) += k3-am6528-iot2050-basic.dtb
 dtb-$(CONFIG_ARCH_K3) += k3-am6528-iot2050-basic-pg2.dtb
 dtb-$(CONFIG_ARCH_K3) += k3-am6548-iot2050-advanced.dtb
+dtb-$(CONFIG_ARCH_K3) += k3-am6548-iot2050-advanced-m2.dtb
 dtb-$(CONFIG_ARCH_K3) += k3-am6548-iot2050-advanced-pg2.dtb
 
+DTC_FLAGS_k3-am6548-iot2050-advanced-m2 += -@
+
 dtb-$(CONFIG_ARCH_K3) += k3-j721e-beagleboneai64.dtb
 dtb-$(CONFIG_ARCH_K3) += k3-j721e-common-proc-board.dtb
 dtb-$(CONFIG_ARCH_K3) += k3-j721e-sk.dtb
arch/arm64/boot/dts/ti/k3-am6548-iot2050-advanced-m2.dts new file +121 -0

121 lines not on this page · raw message

Signature · 1 line
2.35.3
Reviewed-by on v2 3/3
#4 lore raw

Re: [PATCH v2 3/3] arm64: dts: ti: iot2050: Add support for M.2 variant

Quoted 9 lines · Jan Kiszka

From: chao zeng <[email protected]>

The M.2 variant comes with 2 slots, one B-keyed and another one E-keyed. They are configured by the firmware during startup. Also the device tree will be adjusted according to the detect or manually configured interface mode by the firmware. The kernel only carries a single configuration as base device tree. It has to be built with a symbols node so that the firmware can apply overlays for the connector modes.

Quoted 8 lines
[Jan: refactored to a single DT]
---
 arch/arm64/boot/dts/ti/Makefile               |   3 +
 .../dts/ti/k3-am6548-iot2050-advanced-m2.dts  | 121 ++++++++++++++++++
 2 files changed, 124 insertions(+)
 create mode 100644 arch/arm64/boot/dts/ti/k3-am6548-iot2050-advanced-m2.dts

Regards,
Siddharth.