ipmr, ip6mr: Allow MC-routing locally-generated MC packets
Subsystems (10)
v3 cover ipmr, ip6mr: Allow MC-routing locally-generated MC packets
Multicast routing is today handled in the input path. Locally generated MC packets don't hit the IPMR code. Thus if a VXLAN remote address is multicast, the driver needs to set an OIF during route lookup. In practice that means that MC routing configuration needs to be kept in sync with the VXLAN FDB and MDB. Ideally, the VXLAN packets would be routed by the MC routing code instead.
To that end, this patchset adds support to route locally generated multicast packets.
However, an installation that uses a VXLAN underlay netdevice for which it also has matching MC routes, would get a different routing with this patch. Previously, the MC packets would be delivered directly to the underlay port, whereas now they would be MC-routed. In order to avoid this change in behavior, introduce an IPCB/IP6CB flag. Unless the flag is set, the new MC-routing code is skipped.
All this is keyed to a new VXLAN attribute, IFLA_VXLAN_MC_ROUTE. Only when it is set does any of the above engage.
In addition to that, and as is the case today with MC forwarding, IPV4_DEVCONF_MC_FORWARDING must be enabled for the netdevice that acts as a source of MC traffic (i.e. the VXLAN PHYS_DEV), so an MC daemon must be attached to the netdevice.
When a VXLAN netdevice with a MC remote is brought up, the physical netdevice joins the indicated MC group. This is important for local delivery of MC packets, so it is still necessary to configure a physical netdevice -- the parameter cannot go away. The netdevice would however typically not be a front panel port, but a dummy. An MC daemon would then sit on top of that netdevice as well as any front panel ports that it needs to service, and have routes set up between the two.
A way to configure the VXLAN netdevice to take advantage of the new MC routing would be:
# ip link add name d up type dummy # ip link add name vx10 up type vxlan id 1000 dstport 4789 \ local 192.0.2.1 group 225.0.0.1 ttl 16 dev d mrcoute # ip link set dev vx10 master br # plus vlans etc.
With the following MC routes:
(192.0.2.1, 225.0.0.1) iif=d oil=swp1,swp2 # TX route
(*, 225.0.0.1) iif=swp1 oil=d,swp2 # RX route
(*, 225.0.0.1) iif=swp2 oil=d,swp1 # RX route
The RX path has not changed, with the exception of an extra MC hop. Packets are delivered to the front panel port and MC-forwarded to the VXLAN physical port, here "d". Since the port has joined the multicast group, the packets are locally delivered, and end up being processed by the VXLAN netdevice.
This patchset is based on earlier patches from Nikolay Aleksandrov and Roopa Prabhu, though it underwent significant changes. Roopa broadly presented the topic on LPC 2019 [0].
Patchset progression:
- Patches #1 to #4 add ip_mr_output()
- Patches #5 to #10 add ip6_mr_output()
- Patch #11 adds the VXLAN bits to enable MR engagement
- Patches #12 to #14 prepare selftest libraries
- Patch #15 includes a new test suite
[0] https://www.youtube.com/watch?v=xlReECfi-uo
v3:
- Patch #4:
- Reindent the TTL condition
- Refold the skb2 = skb_clone() code
- Patch #8:
- New patch
- Patch #9:
- Move kfree_skb() to the ip6mr_prepare_xmit() caller, like IPv4.
- The patch is now structurally so similar to the IPv4 one that the subject should reflect that. Update.
- Patch #10:
- kfree_skb() now needs to be in ip6mr_output2()
- The fallback version of ip6_mr_output(), compiled when IPV6_MROUTE is not defined, needs to call ip6_output() instead of silently leaking the SKB.
- Reindent the TTL condition
- Refold the skb2 = skb_clone() code
- Patch #15:
- Disable shellchecking apparently-unreachable commands. They are actually reachable through tests_run, in_ns, etc.
- Run setup_wait with an explicit argument to avoid shellcheck citation.
v2:
- Patches #11, #13 and #14:
- Adjust as per shellcheck citations
- Retain Nik's R-b at patch #13, the changes were very minor.
Petr Machata (15):
net: ipv4: Add a flags argument to iptunnel_xmit(),
udp_tunnel_xmit_skb()
net: ipv4: ipmr: ipmr_queue_xmit(): Drop local variable `dev'
net: ipv4: ipmr: Split ipmr_queue_xmit() in two
net: ipv4: Add ip_mr_output()
net: ipv6: Make udp_tunnel6_xmit_skb() void
net: ipv6: Add a flags argument to ip6tunnel_xmit(),
udp_tunnel6_xmit_skb()
net: ipv6: ip6mr: Fix in/out netdev to pass to the FORWARD chain
net: ipv6: ip6mr: Make ip6mr_forward2() void
net: ipv6: ip6mr: Split ip6mr_forward2() in two
net: ipv6: Add ip6_mr_output()
vxlan: Support MC routing in the underlay
selftests: forwarding: lib: Move smcrouted helpers here
selftests: net: lib: Add ip_link_has_flag()
selftests: forwarding: adf_mcd_start(): Allow configuring custom
interfaces
selftests: forwarding: Add a test for verifying VXLAN MC underlay
drivers/net/amt.c | 9 +- drivers/net/bareudp.c | 7 +- drivers/net/geneve.c | 7 +- drivers/net/gtp.c | 12 +- drivers/net/ovpn/udp.c | 4 +- drivers/net/vxlan/vxlan_core.c | 23 +- drivers/net/wireguard/socket.c | 4 +- include/linux/ipv6.h | 1 + include/linux/mroute6.h | 7 + include/net/ip.h | 2 + include/net/ip6_tunnel.h | 3 +- include/net/ip_tunnels.h | 2 +- include/net/udp_tunnel.h | 17 +- include/net/vxlan.h | 5 +- include/uapi/linux/if_link.h | 1 + net/ipv4/ip_tunnel.c | 4 +- net/ipv4/ip_tunnel_core.c | 4 +- net/ipv4/ipmr.c | 169 +++- net/ipv4/route.c | 2 +- net/ipv4/udp_tunnel_core.c | 5 +- net/ipv6/ip6_tunnel.c | 2 +- net/ipv6/ip6_udp_tunnel.c | 18 +- net/ipv6/ip6mr.c | 148 +++- net/ipv6/route.c | 1 + net/ipv6/sit.c | 2 +- net/sctp/ipv6.c | 7 +- net/sctp/protocol.c | 3 +- net/tipc/udp_media.c | 12 +- .../testing/selftests/net/forwarding/Makefile | 1 + tools/testing/selftests/net/forwarding/lib.sh | 46 ++ .../net/forwarding/router_multicast.sh | 35 +- .../net/forwarding/vxlan_bridge_1q_mc_ul.sh | 771 ++++++++++++++++++ tools/testing/selftests/net/lib.sh | 12 +- 33 files changed, 1225 insertions(+), 121 deletions(-) create mode 100755 tools/testing/selftests/net/forwarding/vxlan_bridge_1q_mc_ul.sh
Signature · 1 line
2.49.0
PATCH v3 1/15 net: ipv4: Add a flags argument to iptunnel_xmit(), udp_tunnel_xmit_skb()
iptunnel_xmit() erases the contents of the SKB control block. In order to be able to set particular IPCB flags on the SKB, add a corresponding parameter, and propagate it to udp_tunnel_xmit_skb() as well.
In one of the following patches, VXLAN driver will use this facility to mark packets as subject to IP multicast routing.
---
Notes:
CC: Pablo Neira Ayuso <[email protected]>
CC: [email protected]
CC: Andrew Lunn <[email protected]>
CC: Taehee Yoo <[email protected]>
CC: Antonio Quartulli <[email protected]>
CC: "Jason A. Donenfeld" <[email protected]>
CC: [email protected]
CC: Marcelo Ricardo Leitner <[email protected]>
CC: [email protected]
CC: Jon Maloy <[email protected]>
CC: [email protected]
drivers/net/amt.c | 9 ++++++--- drivers/net/bareudp.c | 4 ++-- drivers/net/geneve.c | 4 ++-- drivers/net/gtp.c | 10 ++++++---- drivers/net/ovpn/udp.c | 2 +- drivers/net/vxlan/vxlan_core.c | 2 +- drivers/net/wireguard/socket.c | 2 +- include/net/ip_tunnels.h | 2 +- include/net/udp_tunnel.h | 2 +- net/ipv4/ip_tunnel.c | 4 ++-- net/ipv4/ip_tunnel_core.c | 4 +++- net/ipv4/udp_tunnel_core.c | 5 +++-- net/ipv6/sit.c | 2 +- net/sctp/protocol.c | 3 ++- net/tipc/udp_media.c | 2 +- 15 files changed, 33 insertions(+), 24 deletions(-)
drivers/net/amt.c +6 -3
@@ -1046,7 +1046,8 @@ static bool amt_send_membership_update(struct amt_dev *amt, amt->gw_port, amt->relay_port, false, - false); + false, + 0);amt_update_gw_status (amt,AMT_STATUS_SENT_UPDATE , true);return false; }
@@ -1103,7 +1104,8 @@ static void amt_send_multicast_data(struct amt_dev *amt, amt->relay_port, tunnel->source_port, false, - false); + false, + 0); } static bool amt_send_membership_query(struct amt_dev *amt,
@@ -1161,7 +1163,8 @@ static bool amt_send_membership_query(struct amt_dev *amt, amt->relay_port, tunnel->source_port, false, - false); + false, + 0);amt_update_relay_status (tunnel,AMT_STATUS_SENT_QUERY , true);return false; }
drivers/net/bareudp.c +2 -2
@@ -362,8 +362,8 @@ static int bareudp_xmit_skb(struct sk_buff *skb, struct net_device *dev,udp_tunnel_xmit_skb (rt, sock->sk, skb, saddr, info->key.u.ipv4.dst, tos, ttl, df, sport, bareudp->port, !net_eq (bareudp->net,dev_net (bareudp->dev)), - !test_bit (IP_TUNNEL_CSUM_BIT , - info->key.tun_flags)); + !test_bit (IP_TUNNEL_CSUM_BIT , info->key.tun_flags), +0 );return 0 ; free_dst:
drivers/net/geneve.c +2 -2
@@ -921,8 +921,8 @@ static int geneve_xmit_skb(struct sk_buff *skb, struct net_device *dev,udp_tunnel_xmit_skb (rt, gs4->sock->sk, skb, saddr, info->key.u.ipv4.dst, tos, ttl, df, sport, geneve->cfg.info.key.tp_dst, !net_eq (geneve->net,dev_net (geneve->dev)), - !test_bit (IP_TUNNEL_CSUM_BIT , - info->key.tun_flags)); + !test_bit (IP_TUNNEL_CSUM_BIT , info->key.tun_flags), +0 );return 0 ; }
drivers/net/gtp.c +6 -4
@@ -446,7 +446,8 @@ static int gtp0_send_echo_resp_ip(struct gtp_dev *gtp, struct sk_buff *skb)htons (GTP0_PORT ),htons (GTP0_PORT ), !net_eq (sock_net (gtp->sk1u),dev_net (gtp->dev)), - false); + false, + 0);return 0 ; }
@@ -704,7 +705,8 @@ static int gtp1u_send_echo_resp(struct gtp_dev *gtp, struct sk_buff *skb)htons (GTP1U_PORT ),htons (GTP1U_PORT ), !net_eq (sock_net (gtp->sk1u),dev_net (gtp->dev)), - false); + false, + 0);return 0 ; }
@@ -1304,7 +1306,7 @@ static netdev_tx_t gtp_dev_xmit(struct sk_buff *skb, struct net_device *dev) pktinfo.gtph_port, pktinfo.gtph_port, !net_eq (sock_net (pktinfo.pctx->sk),dev_net (dev)), - false); + false, 0);break ;case AF_INET6 :#if IS_ENABLED (CONFIG_IPV6 )
@@ -2405,7 +2407,7 @@ static int gtp_genl_send_echo_req(struct sk_buff *skb, struct genl_info *info) port, port, !net_eq (sock_net (sk),dev_net (gtp->dev)), - false); + false, 0);return 0 ; }
drivers/net/ovpn/udp.c +1 -1
@@ -199,7 +199,7 @@ static int ovpn_udp4_output(struct ovpn_peer *peer, struct ovpn_bind *bind, transmit:udp_tunnel_xmit_skb (rt, sk, skb, fl.saddr, fl.daddr,0 ,ip4_dst_hoplimit (&rt->dst),0 , fl.fl4_sport, - fl.fl4_dport, false, sk->sk_no_check_tx); + fl.fl4_dport, false, sk->sk_no_check_tx,0 ); ret =0 ; err:local_bh_enable ();
drivers/net/vxlan/vxlan_core.c +1 -1
@@ -2522,7 +2522,7 @@ void vxlan_xmit_one(struct sk_buff *skb, struct net_device *dev,udp_tunnel_xmit_skb (rt, sock4->sock->sk, skb, saddr, pkey->u.ipv4.dst, tos, ttl, df, - src_port, dst_port, xnet, !udp_sum); + src_port, dst_port, xnet, !udp_sum,0 );#if IS_ENABLED (CONFIG_IPV6 ) } else {struct vxlan_sock *sock6 =rcu_dereference (vxlan->vn6_sock);
drivers/net/wireguard/socket.c +1 -1
@@ -84,7 +84,7 @@ static int send4(struct wg_device *wg, struct sk_buff *skb, skb->ignore_df =1 ;udp_tunnel_xmit_skb (rt, sock, skb, fl.saddr, fl.daddr, ds,ip4_dst_hoplimit (&rt->dst),0 , fl.fl4_sport, - fl.fl4_dport, false, false); + fl.fl4_dport, false, false,0 ); goto out; err:
include/net/ip_tunnels.h +1 -1
@@ -603,7 +603,7 @@ static inline int iptunnel_pull_header(struct sk_buff *skb, int hdr_len,void iptunnel_xmit (struct sock *sk,struct rtable *rt,struct sk_buff *skb,__be32 src,__be32 dst,u8 proto, -u8 tos,u8 ttl,__be16 df,bool xnet); +u8 tos,u8 ttl,__be16 df,bool xnet,u16 ipcb_flags);struct metadata_dst *iptunnel_metadata_reply (struct metadata_dst *md,gfp_t flags); int skb_tunnel_check_pmtu(struct sk_buff *skb, struct dst_entry *encap_dst,
include/net/udp_tunnel.h +1 -1
@@ -150,7 +150,7 @@ static inline void udp_tunnel_drop_rx_info(struct net_device *dev)void udp_tunnel_xmit_skb (struct rtable *rt,struct sock *sk,struct sk_buff *skb,__be32 src,__be32 dst,__u8 tos,__u8 ttl,__be16 df,__be16 src_port,__be16 dst_port, -bool xnet,bool nocheck); +bool xnet,bool nocheck,u16 ipcb_flags); int udp_tunnel6_xmit_skb(struct dst_entry *dst, struct sock *sk, struct sk_buff *skb,
net/ipv4/ip_tunnel.c +2 -2
@@ -668,7 +668,7 @@ void ip_md_tunnel_xmit(struct sk_buff *skb, struct net_device *dev,ip_tunnel_adj_headroom (dev, headroom);iptunnel_xmit (NULL , rt, skb, fl4.saddr, fl4.daddr, proto, tos, ttl, - df, !net_eq (tunnel->net,dev_net (dev))); + df, !net_eq (tunnel->net,dev_net (dev)),0 );return ; tx_error:DEV_STATS_INC (dev, tx_errors);
@@ -857,7 +857,7 @@ void ip_tunnel_xmit(struct sk_buff *skb, struct net_device *dev,ip_tunnel_adj_headroom (dev, max_headroom);iptunnel_xmit (NULL , rt, skb, fl4.saddr, fl4.daddr, protocol, tos, ttl, - df, !net_eq (tunnel->net,dev_net (dev))); + df, !net_eq (tunnel->net,dev_net (dev)),0 );return ;#if IS_ENABLED (CONFIG_IPV6 )
net/ipv4/ip_tunnel_core.c +3 -1
@@ -49,7 +49,8 @@ EXPORT_SYMBOL(ip6tun_encaps);void iptunnel_xmit (struct sock *sk,struct rtable *rt,struct sk_buff *skb,__be32 src,__be32 dst,__u8 proto, -__u8 tos,__u8 ttl,__be16 df,bool xnet) +__u8 tos,__u8 ttl,__be16 df,bool xnet, +u16 ipcb_flags) {int pkt_len = skb->len -skb_inner_network_offset (skb);struct net *net =dev_net (rt->dst.dev);
@@ -62,6 +63,7 @@ void iptunnel_xmit(struct sock *sk, struct rtable *rt, struct sk_buff *skb,skb_clear_hash_if_not_l4 (skb);skb_dst_set (skb, &rt->dst);memset (IPCB (skb),0 ,sizeof (*IPCB (skb))); +IPCB (skb)->flags = ipcb_flags;/* Push down and install the IP header. */ skb_push (skb,sizeof (struct iphdr ));
net/ipv4/udp_tunnel_core.c +3 -2
@@ -169,7 +169,7 @@ EXPORT_SYMBOL_GPL(udp_tunnel_notify_del_rx_port);void udp_tunnel_xmit_skb (struct rtable *rt,struct sock *sk,struct sk_buff *skb,__be32 src,__be32 dst,__u8 tos,__u8 ttl,__be16 df,__be16 src_port,__be16 dst_port, -bool xnet,bool nocheck) +bool xnet,bool nocheck,u16 ipcb_flags) {struct udphdr *uh;
@@ -185,7 +185,8 @@ void udp_tunnel_xmit_skb(struct rtable *rt, struct sock *sk, struct sk_buff *skbudp_set_csum (nocheck, skb, src, dst, skb->len); -iptunnel_xmit (sk, rt, skb, src, dst,IPPROTO_UDP , tos, ttl, df, xnet); +iptunnel_xmit (sk, rt, skb, src, dst,IPPROTO_UDP , tos, ttl, df, xnet, + ipcb_flags); }EXPORT_SYMBOL_GPL (udp_tunnel_xmit_skb);
net/ipv6/sit.c +1 -1
@@ -1035,7 +1035,7 @@ static netdev_tx_t ipip6_tunnel_xmit(struct sk_buff *skb,skb_set_inner_ipproto (skb,IPPROTO_IPV6 );iptunnel_xmit (NULL , rt, skb, fl4.saddr, fl4.daddr, protocol, tos, ttl, - df, !net_eq (tunnel->net,dev_net (dev))); + df, !net_eq (tunnel->net,dev_net (dev)),0 );return NETDEV_TX_OK ; tx_error_icmp:
net/sctp/protocol.c +2 -1
@@ -1103,7 +1103,8 @@ static inline int sctp_v4_xmit(struct sk_buff *skb, struct sctp_transport *t)skb_set_inner_ipproto (skb,IPPROTO_SCTP );udp_tunnel_xmit_skb (dst_rtable (dst), sk, skb, fl4->saddr, fl4->daddr, dscp,ip4_dst_hoplimit (dst), df, -sctp_sk (sk)->udp_port, t->encap_port, false, false); +sctp_sk (sk)->udp_port, t->encap_port, false, false, +0 );return 0 ; }
net/tipc/udp_media.c +1 -1
@@ -197,7 +197,7 @@ static int tipc_udp_xmit(struct net *net, struct sk_buff *skb, ttl =ip4_dst_hoplimit (&rt->dst);udp_tunnel_xmit_skb (rt, ub->ubsock->sk, skb, src->ipv4.s_addr, dst->ipv4.s_addr,0 , ttl,0 , src->port, - dst->port, false, true); + dst->port, false, true,0 );#if IS_ENABLED (CONFIG_IPV6 ) } else {if (!ndst) {
Signature · 1 line
2.49.0
PATCH v3 2/15 net: ipv4: ipmr: ipmr_queue_xmit(): Drop local variable `dev'
In reply to Petr MachataThe variable is used for caching of rt->dst.dev. The netdevice referenced therein does not change during the scope of validity of that local. At the same time, the local is only used twice, and each of these uses will end up in a different function in the following patches, further eliminating any use the local could have had.
Drop the local altogether and inline the uses.
--- net/ipv4/ipmr.c | 7 ++----- 1 file changed, 2 insertions(+), 5 deletions(-)
net/ipv4/ipmr.c +2 -5
@@ -1859,7 +1859,6 @@ static void ipmr_queue_xmit(struct net *net, struct mr_table *mrt,const struct iphdr *iph =ip_hdr (skb);struct vif_device *vif = &mrt->vif_table[vifi];struct net_device *vif_dev; -struct net_device *dev;struct rtable *rt;struct flowi4 fl4;int encap =0 ;
@@ -1898,8 +1897,6 @@ static void ipmr_queue_xmit(struct net *net, struct mr_table *mrt, goto out_free; } - dev = rt->dst.dev; -if (skb->len+encap >dst_mtu (&rt->dst) && (ntohs (iph->frag_off) &IP_DF )) {/* Do not fragment multicasts. Alas, IPv4 does not * allow to send ICMP, so that packets will disappear
@@ -1910,7 +1907,7 @@ static void ipmr_queue_xmit(struct net *net, struct mr_table *mrt, goto out_free; } - encap +=LL_RESERVED_SPACE (dev) + rt->dst.header_len; + encap +=LL_RESERVED_SPACE (rt->dst.dev) + rt->dst.header_len;if (skb_cow (skb, encap)) {ip_rt_put (rt);
@@ -1947,7 +1944,7 @@ static void ipmr_queue_xmit(struct net *net, struct mr_table *mrt,* result in receiving multiple packets. */ NF_HOOK (NFPROTO_IPV4 ,NF_INET_FORWARD , - net,NULL , skb, skb->dev, dev, + net,NULL , skb, skb->dev, rt->dst.dev, ipmr_forward_finish);return ;
Signature · 1 line
2.49.0
PATCH v3 3/15 net: ipv4: ipmr: Split ipmr_queue_xmit() in two
In reply to Petr MachataSome of the work of ipmr_queue_xmit() is specific to IPMR forwarding, and should not take place on the output path. In order to allow reuse of the common parts, split the function into two: the ipmr_prepare_xmit() helper that takes care of the common bits, and the ipmr_queue_fwd_xmit(), which invokes the former and encapsulates the whole forwarding algorithm.
--- net/ipv4/ipmr.c | 45 +++++++++++++++++++++++++++++---------------- 1 file changed, 29 insertions(+), 16 deletions(-)
net/ipv4/ipmr.c +29 -16
@@ -1853,8 +1853,8 @@ static bool ipmr_forward_offloaded(struct sk_buff *skb, struct mr_table *mrt,/* Processing handlers for ipmr_forward, under rcu_read_lock() */ -static void ipmr_queue_xmit (struct net *net,struct mr_table *mrt, -int in_vifi,struct sk_buff *skb,int vifi) +static int ipmr_prepare_xmit (struct net *net,struct mr_table *mrt, +struct sk_buff *skb,int vifi) {const struct iphdr *iph =ip_hdr (skb);struct vif_device *vif = &mrt->vif_table[vifi];
@@ -1865,7 +1865,7 @@ static void ipmr_queue_xmit(struct net *net, struct mr_table *mrt, vif_dev =vif_dev_read (vif);if (!vif_dev) - goto out_free; +return -1 ;if (vif->flags &VIFF_REGISTER ) {WRITE_ONCE (vif->pkt_out, vif->pkt_out +1 );
@@ -1873,12 +1873,9 @@ static void ipmr_queue_xmit(struct net *net, struct mr_table *mrt,DEV_STATS_ADD (vif_dev, tx_bytes, skb->len);DEV_STATS_INC (vif_dev, tx_packets);ipmr_cache_report (mrt, skb, vifi,IGMPMSG_WHOLEPKT ); - goto out_free; +return -1 ; } -if (ipmr_forward_offloaded (skb, mrt, in_vifi, vifi)) - goto out_free; -if (vif->flags &VIFF_TUNNEL ) { rt = ip_route_output_ports(net, &fl4, NULL, vif->remote, vif->local,
@@ -1886,7 +1883,7 @@ static void ipmr_queue_xmit(struct net *net, struct mr_table *mrt,IPPROTO_IPIP , iph->tos & INET_DSCP_MASK, vif->link);if (IS_ERR (rt)) - goto out_free; +return -1 ; encap =sizeof (struct iphdr ); }else { rt = ip_route_output_ports(net, &fl4, NULL, iph->daddr, 0,
@@ -1894,7 +1891,7 @@ static void ipmr_queue_xmit(struct net *net, struct mr_table *mrt,IPPROTO_IPIP , iph->tos & INET_DSCP_MASK, vif->link);if (IS_ERR (rt)) - goto out_free; +return -1 ; }if (skb->len+encap >dst_mtu (&rt->dst) && (ntohs (iph->frag_off) &IP_DF )) {
@@ -1904,14 +1901,14 @@ static void ipmr_queue_xmit(struct net *net, struct mr_table *mrt,*/ IP_INC_STATS (net,IPSTATS_MIB_FRAGFAILS );ip_rt_put (rt); - goto out_free; +return -1 ; } encap +=LL_RESERVED_SPACE (rt->dst.dev) + rt->dst.header_len;if (skb_cow (skb, encap)) {ip_rt_put (rt); - goto out_free; +return -1 ; }WRITE_ONCE (vif->pkt_out, vif->pkt_out +1 );
@@ -1931,6 +1928,22 @@ static void ipmr_queue_xmit(struct net *net, struct mr_table *mrt,DEV_STATS_ADD (vif_dev, tx_bytes, skb->len); } +return 0 ; +} + +static void ipmr_queue_fwd_xmit (struct net *net,struct mr_table *mrt, +int in_vifi,struct sk_buff *skb,int vifi) +{ +struct rtable *rt; + +if (ipmr_forward_offloaded (skb, mrt, in_vifi, vifi)) + goto out_free; + +if (ipmr_prepare_xmit (net, mrt, skb, vifi)) + goto out_free; + + rt =skb_rtable (skb); +IPCB (skb)->flags |=IPSKB_FORWARDED ;/* RFC1584 teaches, that DVMRP/PIM router must deliver packets locally
@@ -2062,8 +2075,8 @@ static void ip_mr_forward(struct net *net, struct mr_table *mrt,struct sk_buff *skb2 =skb_clone (skb,GFP_ATOMIC );if (skb2) -ipmr_queue_xmit (net, mrt, true_vifi, - skb2, psend); +ipmr_queue_fwd_xmit (net, mrt, true_vifi, + skb2, psend); } psend = ct; }
@@ -2074,10 +2087,10 @@ static void ip_mr_forward(struct net *net, struct mr_table *mrt,struct sk_buff *skb2 =skb_clone (skb,GFP_ATOMIC );if (skb2) -ipmr_queue_xmit (net, mrt, true_vifi, skb2, - psend); +ipmr_queue_fwd_xmit (net, mrt, true_vifi, skb2, + psend); }else { -ipmr_queue_xmit (net, mrt, true_vifi, skb, psend); +ipmr_queue_fwd_xmit (net, mrt, true_vifi, skb, psend);return ; } }
Signature · 1 line
2.49.0
PATCH v3 4/15 net: ipv4: Add ip_mr_output()
In reply to Petr MachataMulticast routing is today handled in the input path. Locally generated MC packets don't hit the IPMR code today. Thus if a VXLAN remote address is multicast, the driver needs to set an OIF during route lookup. Thus MC routing configuration needs to be kept in sync with the VXLAN FDB and MDB. Ideally, the VXLAN packets would be routed by the MC routing code instead.
To that end, this patch adds support to route locally generated multicast packets. The newly-added routines do largely what ip_mr_input() and ip_mr_forward() do: make an MR cache lookup to find where to send the packets, and use ip_mc_output() to send each of them. When no cache entry is found, the packet is punted to the daemon for resolution.
However, an installation that uses a VXLAN underlay netdevice for which it also has matching MC routes, would get a different routing with this patch. Previously, the MC packets would be delivered directly to the underlay port, whereas now they would be MC-routed. In order to avoid this change in behavior, introduce an IPCB flag. Only if the flag is set will ip_mr_output() actually engage, otherwise it reverts to ip_mc_output().
This code is based on work by Roopa Prabhu and Nikolay Aleksandrov.
---
Notes:
v3:
- Reindent the TTL condition
- Refold the skb2 = skb_clone() code
include/net/ip.h | 2 + net/ipv4/ipmr.c | 117 +++++++++++++++++++++++++++++++++++++++++++++++ net/ipv4/route.c | 2 +- 3 files changed, 120 insertions(+), 1 deletion(-)
include/net/ip.h +2 -0
@@ -59,6 +59,7 @@ struct inet_skb_parm {#define IPSKB_L3SLAVE BIT(7)#define IPSKB_NOPOLICY BIT(8)#define IPSKB_MULTIPATH BIT(9) +#define IPSKB_MCROUTE BIT(10)u16 frag_max_size; };
@@ -167,6 +168,7 @@ void ip_list_rcv(struct list_head *head, struct packet_type *pt,int ip_local_deliver (struct sk_buff *skb);void ip_protocol_deliver_rcu (struct net *net,struct sk_buff *skb,int proto);int ip_mr_input (struct sk_buff *skb); +int ip_mr_output (struct net *net,struct sock *sk,struct sk_buff *skb);int ip_output (struct net *net,struct sock *sk,struct sk_buff *skb);int ip_mc_output (struct net *net,struct sock *sk,struct sk_buff *skb); int ip_do_fragment(struct net *net, struct sock *sk, struct sk_buff *skb,
net/ipv4/ipmr.c +117 -0
129 lines not on this page · raw message
net/ipv4/route.c +1 -1
@@ -2660,7 +2660,7 @@ static struct rtable *__mkroute_output(const struct fib_result *res,if (IN_DEV_MFORWARD (in_dev) && !ipv4_is_local_multicast (fl4->daddr)) { rth->dst.input = ip_mr_input; - rth->dst.output = ip_mc_output; + rth->dst.output = ip_mr_output; } }#endif
Signature · 1 line
2.49.0
PATCH v3 5/15 net: ipv6: Make udp_tunnel6_xmit_skb() void
In reply to Petr MachataThe function always returns zero, thus the return value does not carry any signal. Just make it void.
Most callers already ignore the return value. However:
- Refold arguments of the call from sctp_v6_xmit() so that they fit into the 80-column limit.
- tipc_udp_xmit() initializes err from the return value, but that should already be always zero at that point. So there's no practical change, but elision of the assignment prompts a couple more tweaks to clean up the function.
---
Notes:
CC: Marcelo Ricardo Leitner <[email protected]>
CC: [email protected]
CC: Jon Maloy <[email protected]>
CC: [email protected]
include/net/udp_tunnel.h | 14 +++++++------- net/ipv6/ip6_udp_tunnel.c | 15 +++++++-------- net/sctp/ipv6.c | 7 ++++--- net/tipc/udp_media.c | 10 +++++----- 4 files changed, 23 insertions(+), 23 deletions(-)
include/net/udp_tunnel.h +7 -7
@@ -152,13 +152,13 @@ void udp_tunnel_xmit_skb(struct rtable *rt, struct sock *sk, struct sk_buff *skb __be16 df, __be16 src_port, __be16 dst_port, bool xnet, bool nocheck, u16 ipcb_flags); -int udp_tunnel6_xmit_skb (struct dst_entry *dst,struct sock *sk, -struct sk_buff *skb, -struct net_device *dev, -const struct in6_addr *saddr, -const struct in6_addr *daddr, -__u8 prio,__u8 ttl,__be32 label, -__be16 src_port,__be16 dst_port,bool nocheck); +void udp_tunnel6_xmit_skb (struct dst_entry *dst,struct sock *sk, +struct sk_buff *skb, +struct net_device *dev, +const struct in6_addr *saddr, +const struct in6_addr *daddr, +__u8 prio,__u8 ttl,__be32 label, +__be16 src_port,__be16 dst_port,bool nocheck);void udp_tunnel_sock_release (struct socket *sock);
net/ipv6/ip6_udp_tunnel.c +7 -8
@@ -74,13 +74,13 @@ int udp_sock_create6(struct net *net, struct udp_port_cfg *cfg, }EXPORT_SYMBOL_GPL (udp_sock_create6); -int udp_tunnel6_xmit_skb (struct dst_entry *dst,struct sock *sk, -struct sk_buff *skb, -struct net_device *dev, -const struct in6_addr *saddr, -const struct in6_addr *daddr, -__u8 prio,__u8 ttl,__be32 label, -__be16 src_port,__be16 dst_port,bool nocheck) +void udp_tunnel6_xmit_skb (struct dst_entry *dst,struct sock *sk, +struct sk_buff *skb, +struct net_device *dev, +const struct in6_addr *saddr, +const struct in6_addr *daddr, +__u8 prio,__u8 ttl,__be32 label, +__be16 src_port,__be16 dst_port,bool nocheck) {struct udphdr *uh;struct ipv6hdr *ip6h;
@@ -109,7 +109,6 @@ int udp_tunnel6_xmit_skb(struct dst_entry *dst, struct sock *sk, ip6h->saddr = *saddr;ip6tunnel_xmit (sk, skb, dev); -return 0 ; }EXPORT_SYMBOL_GPL (udp_tunnel6_xmit_skb);
net/sctp/ipv6.c +4 -3
@@ -261,9 +261,10 @@ static int sctp_v6_xmit(struct sk_buff *skb, struct sctp_transport *t)skb_set_inner_ipproto (skb,IPPROTO_SCTP ); label =ip6_make_flowlabel (sock_net (sk), skb, fl6->flowlabel, true, fl6); -return udp_tunnel6_xmit_skb (dst, sk, skb,NULL , &fl6->saddr, - &fl6->daddr, tclass,ip6_dst_hoplimit (dst), - label,sctp_sk (sk)->udp_port, t->encap_port, false); +udp_tunnel6_xmit_skb (dst, sk, skb,NULL , &fl6->saddr, &fl6->daddr, + tclass,ip6_dst_hoplimit (dst), label, +sctp_sk (sk)->udp_port, t->encap_port, false); +return 0 ; }/* Returns the dst cache entry for the given source and destination ip
net/tipc/udp_media.c +5 -5
@@ -172,7 +172,7 @@ static int tipc_udp_xmit(struct net *net, struct sk_buff *skb, struct udp_media_addr *dst, struct dst_cache *cache) { struct dst_entry *ndst; -int ttl, err =0 ; +int ttl, err;local_bh_disable (); ndst =dst_cache_get (cache);
@@ -217,13 +217,13 @@ static int tipc_udp_xmit(struct net *net, struct sk_buff *skb, dst_cache_set_ip6(cache, ndst, &fl6.saddr); } ttl =ip6_dst_hoplimit (ndst); - err =udp_tunnel6_xmit_skb (ndst, ub->ubsock->sk, skb,NULL , - &src->ipv6, &dst->ipv6,0 , ttl,0 , - src->port, dst->port, false); +udp_tunnel6_xmit_skb (ndst, ub->ubsock->sk, skb,NULL , + &src->ipv6, &dst->ipv6,0 , ttl,0 , + src->port, dst->port, false);#endif }local_bh_enable (); -return err; +return 0 ; tx_error:local_bh_enable ();
Signature · 1 line
2.49.0
PATCH v3 6/15 net: ipv6: Add a flags argument to ip6tunnel_xmit(), udp_tunnel6_xmit_skb()
In reply to Petr Machataip6tunnel_xmit() erases the contents of the SKB control block. In order to be able to set particular IP6CB flags on the SKB, add a corresponding parameter, and propagate it to udp_tunnel6_xmit_skb() as well.
In one of the following patches, VXLAN driver will use this facility to mark packets as subject to IPv6 multicast routing.
---
Notes:
CC: Pablo Neira Ayuso <[email protected]>
CC: [email protected]
CC: Andrew Lunn <[email protected]>
CC: Antonio Quartulli <[email protected]>
CC: "Jason A. Donenfeld" <[email protected]>
CC: [email protected]
CC: Marcelo Ricardo Leitner <[email protected]>
CC: [email protected]
CC: Jon Maloy <[email protected]>
CC: [email protected]
drivers/net/bareudp.c | 3 ++- drivers/net/geneve.c | 3 ++- drivers/net/gtp.c | 2 +- drivers/net/ovpn/udp.c | 2 +- drivers/net/vxlan/vxlan_core.c | 3 ++- drivers/net/wireguard/socket.c | 2 +- include/net/ip6_tunnel.h | 3 ++- include/net/udp_tunnel.h | 3 ++- net/ipv6/ip6_tunnel.c | 2 +- net/ipv6/ip6_udp_tunnel.c | 5 +++-- net/sctp/ipv6.c | 2 +- net/tipc/udp_media.c | 2 +- 12 files changed, 19 insertions(+), 13 deletions(-)
drivers/net/bareudp.c +2 -1
@@ -431,7 +431,8 @@ static int bareudp6_xmit_skb(struct sk_buff *skb, struct net_device *dev, &saddr, &daddr, prio, ttl, info->key.label, sport, bareudp->port, !test_bit (IP_TUNNEL_CSUM_BIT , - info->key.tun_flags)); + info->key.tun_flags), + 0);return 0 ; free_dst:
drivers/net/geneve.c +2 -1
@@ -1014,7 +1014,8 @@ static int geneve6_xmit_skb(struct sk_buff *skb, struct net_device *dev, &saddr, &key->u.ipv6.dst, prio, ttl, info->key.label, sport, geneve->cfg.info.key.tp_dst, !test_bit (IP_TUNNEL_CSUM_BIT , - info->key.tun_flags)); + info->key.tun_flags), + 0); return 0; }#endif
drivers/net/gtp.c +1 -1
@@ -1316,7 +1316,7 @@ static netdev_tx_t gtp_dev_xmit(struct sk_buff *skb, struct net_device *dev)ip6_dst_hoplimit (&pktinfo.rt->dst),0 , pktinfo.gtph_port, pktinfo.gtph_port, - false); + false, 0);#else goto tx_err;#endif
drivers/net/ovpn/udp.c +1 -1
@@ -274,7 +274,7 @@ static int ovpn_udp6_output(struct ovpn_peer *peer, struct ovpn_bind *bind, skb->ignore_df =1 ;udp_tunnel6_xmit_skb (dst, sk, skb, skb->dev, &fl.saddr, &fl.daddr,0 ,ip6_dst_hoplimit (dst),0 , fl.fl6_sport, - fl.fl6_dport,udp_get_no_check6_tx (sk)); + fl.fl6_dport,udp_get_no_check6_tx (sk),0 ); ret =0 ; err:local_bh_enable ();
drivers/net/vxlan/vxlan_core.c +2 -1
@@ -2586,7 +2586,8 @@ void vxlan_xmit_one(struct sk_buff *skb, struct net_device *dev,udp_tunnel6_xmit_skb (ndst, sock6->sock->sk, skb, dev, &saddr, &pkey->u.ipv6.dst, tos, ttl, - pkey->label, src_port, dst_port, !udp_sum); + pkey->label, src_port, dst_port, !udp_sum, +0 );#endif }vxlan_vnifilter_count (vxlan, vni,NULL ,VXLAN_VNI_STATS_TX , pkt_len);
drivers/net/wireguard/socket.c +1 -1
@@ -151,7 +151,7 @@ static int send6(struct wg_device *wg, struct sk_buff *skb, skb->ignore_df =1 ;udp_tunnel6_xmit_skb (dst, sock, skb, skb->dev, &fl.saddr, &fl.daddr, ds,ip6_dst_hoplimit (dst),0 , fl.fl6_sport, - fl.fl6_dport, false); + fl.fl6_dport, false,0 ); goto out; err:
include/net/ip6_tunnel.h +2 -1
@@ -152,11 +152,12 @@ int ip6_tnl_get_iflink(const struct net_device *dev);int ip6_tnl_change_mtu (struct net_device *dev,int new_mtu);static inline void ip6tunnel_xmit (struct sock *sk,struct sk_buff *skb, -struct net_device *dev) +struct net_device *dev,u16 ip6cb_flags) {int pkt_len, err;memset (skb->cb,0 ,sizeof (struct inet6_skb_parm )); +IP6CB (skb)->flags = ip6cb_flags; pkt_len = skb->len -skb_inner_network_offset (skb); err =ip6_local_out (dev_net (skb_dst (skb)->dev), sk, skb);
include/net/udp_tunnel.h +2 -1
@@ -158,7 +158,8 @@ void udp_tunnel6_xmit_skb(struct dst_entry *dst, struct sock *sk,const struct in6_addr *saddr, const struct in6_addr *daddr, __u8 prio, __u8 ttl, __be32 label, - __be16 src_port, __be16 dst_port, bool nocheck); + __be16 src_port, __be16 dst_port, bool nocheck, + u16 ip6cb_flags);void udp_tunnel_sock_release (struct socket *sock);
net/ipv6/ip6_tunnel.c +1 -1
@@ -1278,7 +1278,7 @@ int ip6_tnl_xmit(struct sk_buff *skb, struct net_device *dev, __u8 dsfield, ipv6h->nexthdr = proto; ipv6h->saddr = fl6->saddr; ipv6h->daddr = fl6->daddr; -ip6tunnel_xmit (NULL , skb, dev); +ip6tunnel_xmit (NULL , skb, dev,0 );return 0 ; tx_err_link_failure:DEV_STATS_INC (dev, tx_carrier_errors);
net/ipv6/ip6_udp_tunnel.c +3 -2
@@ -80,7 +80,8 @@ void udp_tunnel6_xmit_skb(struct dst_entry *dst, struct sock *sk,const struct in6_addr *saddr, const struct in6_addr *daddr, __u8 prio, __u8 ttl, __be32 label, - __be16 src_port, __be16 dst_port, bool nocheck) + __be16 src_port, __be16 dst_port, bool nocheck, + u16 ip6cb_flags) { struct udphdr *uh;struct ipv6hdr *ip6h;
@@ -108,7 +109,7 @@ void udp_tunnel6_xmit_skb(struct dst_entry *dst, struct sock *sk, ip6h->daddr = *daddr; ip6h->saddr = *saddr; -ip6tunnel_xmit (sk, skb, dev); +ip6tunnel_xmit (sk, skb, dev, ip6cb_flags); }EXPORT_SYMBOL_GPL (udp_tunnel6_xmit_skb);
net/sctp/ipv6.c +1 -1
@@ -263,7 +263,7 @@ static int sctp_v6_xmit(struct sk_buff *skb, struct sctp_transport *t)udp_tunnel6_xmit_skb (dst, sk, skb,NULL , &fl6->saddr, &fl6->daddr, tclass,ip6_dst_hoplimit (dst), label, -sctp_sk (sk)->udp_port, t->encap_port, false); +sctp_sk (sk)->udp_port, t->encap_port, false,0 );return 0 ; }
net/tipc/udp_media.c +1 -1
@@ -219,7 +219,7 @@ static int tipc_udp_xmit(struct net *net, struct sk_buff *skb, ttl =ip6_dst_hoplimit (ndst);udp_tunnel6_xmit_skb (ndst, ub->ubsock->sk, skb,NULL , &src->ipv6, &dst->ipv6,0 , ttl,0 , - src->port, dst->port, false); + src->port, dst->port, false,0 );#endif }local_bh_enable ();
Signature · 1 line
2.49.0
PATCH v3 7/15 net: ipv6: ip6mr: Fix in/out netdev to pass to the FORWARD chain
In reply to Petr MachataThe netfilter hook is invoked with skb->dev for input netdevice, and vif_dev for output netdevice. However at the point of invocation, skb->dev is already set to vif_dev, and MR-forwarded packets are reported with in=out:
# ip6tables -A FORWARD -j LOG --log-prefix '[forw]' # cd tools/testing/selftests/net/forwarding # ./router_multicast.sh # dmesg | fgrep '[forw]' [ 1670.248245] [forw]IN=v5 OUT=v5 [...]
For reference, IPv4 MR code shows in and out as appropriate. Fix by caching skb->dev and using the updated value for output netdev.
---
Notes:
This never worked correctly, hence going through net-next.
---
CC: YOSHIFUJI Hideaki <[email protected]>
net/ipv6/ip6mr.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-)
net/ipv6/ip6mr.c +2 -1
@@ -2039,6 +2039,7 @@ static int ip6mr_forward2(struct net *net, struct mr_table *mrt, struct sk_buff *skb, int vifi) {struct vif_device *vif = &mrt->vif_table[vifi]; +struct net_device *indev = skb->dev;struct net_device *vif_dev;struct ipv6hdr *ipv6h;struct dst_entry *dst;
@@ -2101,7 +2102,7 @@ static int ip6mr_forward2(struct net *net, struct mr_table *mrt,IP6CB (skb)->flags |=IP6SKB_FORWARDED ;return NF_HOOK (NFPROTO_IPV6 ,NF_INET_FORWARD , - net,NULL , skb, skb->dev, vif_dev, + net,NULL , skb, indev, skb->dev, ip6mr_forward2_finish); out_free:
Signature · 1 line
2.49.0
PATCH v3 8/15 net: ipv6: ip6mr: Make ip6mr_forward2() void
In reply to Petr MachataNobody uses the return value, so convert the function to void.
---
Notes:
v3:
- New patch
net/ipv6/ip6mr.c | 12 ++++++------ 1 file changed, 6 insertions(+), 6 deletions(-)
net/ipv6/ip6mr.c +6 -6
@@ -2035,8 +2035,8 @@ static inline int ip6mr_forward2_finish(struct net *net, struct sock *sk, struct* Processing handlers for ip6mr_forward */ -static int ip6mr_forward2 (struct net *net,struct mr_table *mrt, -struct sk_buff *skb,int vifi) +static void ip6mr_forward2 (struct net *net,struct mr_table *mrt, +struct sk_buff *skb,int vifi) {struct vif_device *vif = &mrt->vif_table[vifi];struct net_device *indev = skb->dev;
@@ -2101,13 +2101,13 @@ static int ip6mr_forward2(struct net *net, struct mr_table *mrt,IP6CB (skb)->flags |=IP6SKB_FORWARDED ; -return NF_HOOK (NFPROTO_IPV6 ,NF_INET_FORWARD , - net,NULL , skb, indev, skb->dev, - ip6mr_forward2_finish); +NF_HOOK (NFPROTO_IPV6 ,NF_INET_FORWARD , + net,NULL , skb, indev, skb->dev, + ip6mr_forward2_finish); +return ; out_free:kfree_skb (skb); -return 0 ; }/* Called with rcu_read_lock() */
Signature · 1 line
2.49.0
PATCH v3 9/15 net: ipv6: ip6mr: Split ip6mr_forward2() in two
In reply to Petr MachataSome of the work of ip6mr_forward2() is specific to IPMR forwarding, and should not take place on the output path. In order to allow reuse of the common parts, extract out of the function a helper, ip6mr_prepare_forward().
---
Notes:
v3:
- Move kfree_skb() to the ip6mr_prepare_xmit() caller, like IPv4.
- The patch is now structurally so similar to the IPv4 one that the subject should reflect that. Update.
net/ipv6/ip6mr.c | 23 ++++++++++++++++------- 1 file changed, 16 insertions(+), 7 deletions(-)
net/ipv6/ip6mr.c +16 -7
@@ -2035,11 +2035,10 @@ static inline int ip6mr_forward2_finish(struct net *net, struct sock *sk, struct* Processing handlers for ip6mr_forward */ -static void ip6mr_forward2 (struct net *net,struct mr_table *mrt, -struct sk_buff *skb,int vifi) +static int ip6mr_prepare_xmit (struct net *net,struct mr_table *mrt, +struct sk_buff *skb,int vifi) {struct vif_device *vif = &mrt->vif_table[vifi]; -struct net_device *indev = skb->dev;struct net_device *vif_dev;struct ipv6hdr *ipv6h;struct dst_entry *dst;
@@ -2047,7 +2046,7 @@ static void ip6mr_forward2(struct net *net, struct mr_table *mrt, vif_dev =vif_dev_read (vif);if (!vif_dev) - goto out_free; +return -1 ;#ifdef CONFIG_IPV6_PIMSM_V2 if (vif->flags &MIFF_REGISTER ) {
@@ -2056,7 +2055,7 @@ static void ip6mr_forward2(struct net *net, struct mr_table *mrt,DEV_STATS_ADD (vif_dev, tx_bytes, skb->len);DEV_STATS_INC (vif_dev, tx_packets);ip6mr_cache_report (mrt, skb, vifi,MRT6MSG_WHOLEPKT ); - goto out_free; + return -1; }#endif
@@ -2070,7 +2069,7 @@ static void ip6mr_forward2(struct net *net, struct mr_table *mrt, dst =ip6_route_output (net,NULL , &fl6);if (dst->error) {dst_release (dst); - goto out_free; +return -1 ; }skb_dst_drop (skb);
@@ -2094,10 +2093,20 @@ static void ip6mr_forward2(struct net *net, struct mr_table *mrt,/* We are about to write */ /* XXX: extension headers? */ if (skb_cow (skb,sizeof (*ipv6h) +LL_RESERVED_SPACE (vif_dev))) - goto out_free; +return -1 ; ipv6h =ipv6_hdr (skb); ipv6h->hop_limit--; +return 0 ; +} + +static void ip6mr_forward2 (struct net *net,struct mr_table *mrt, +struct sk_buff *skb,int vifi) +{ +struct net_device *indev = skb->dev; + +if (ip6mr_prepare_xmit (net, mrt, skb, vifi)) + goto out_free;IP6CB (skb)->flags |=IP6SKB_FORWARDED ;
Signature · 1 line
2.49.0
PATCH v3 10/15 net: ipv6: Add ip6_mr_output()
In reply to Petr MachataMulticast routing is today handled in the input path. Locally generated MC packets don't hit the IPMR code today. Thus if a VXLAN remote address is multicast, the driver needs to set an OIF during route lookup. Thus MC routing configuration needs to be kept in sync with the VXLAN FDB and MDB. Ideally, the VXLAN packets would be routed by the MC routing code instead.
To that end, this patch adds support to route locally generated multicast packets. The newly-added routines do largely what ip6_mr_input() and ip6_mr_forward() do: make an MR cache lookup to find where to send the packets, and use ip6_output() to send each of them. When no cache entry is found, the packet is punted to the daemon for resolution.
Similarly to the IPv4 case in a previous patch, the new logic is contingent on a newly-added IP6CB flag being set.
---
Notes:
v3:
- kfree_skb() now needs to be in ip6mr_output2()
- The fallback version of ip6_mr_output(), compiled when IPV6_MROUTE is not defined, needs to call ip6_output() instead of silently leaking the SKB.
- Reindent the TTL condition
- Refold the skb2 = skb_clone() code
include/linux/ipv6.h | 1 + include/linux/mroute6.h | 7 +++ net/ipv6/ip6mr.c | 118 ++++++++++++++++++++++++++++++++++++++++ net/ipv6/route.c | 1 + 4 files changed, 127 insertions(+)
include/linux/ipv6.h +1 -0
@@ -156,6 +156,7 @@ struct inet6_skb_parm {#define IP6SKB_SEG6 256#define IP6SKB_FAKEJUMBO 512#define IP6SKB_MULTIPATH 1024 +#define IP6SKB_MCROUTE 2048 };#if defined(CONFIG_NET_L3_MASTER_DEV )
include/linux/mroute6.h +7 -0
@@ -31,6 +31,7 @@ extern int ip6_mroute_getsockopt(struct sock *, int, sockptr_t, sockptr_t);extern int ip6_mr_input (struct sk_buff *skb);extern int ip6mr_compat_ioctl (struct sock *sk,unsigned int cmd,void __user *arg);extern int ip6_mr_init (void ); +extern int ip6_mr_output (struct net *net,struct sock *sk,struct sk_buff *skb);extern void ip6_mr_cleanup (void );int ip6mr_ioctl (struct sock *sk,int cmd,void *arg);#else
@@ -58,6 +59,12 @@ static inline int ip6_mr_init(void)return 0 ; } +static inline int +ip6_mr_output (struct net *net,struct sock *sk,struct sk_buff *skb) +{ +return ip6_output (net, sk, skb); +} +static inline void ip6_mr_cleanup (void ) {return ;
net/ipv6/ip6mr.c +118 -0
136 lines not on this page · raw message
net/ipv6/route.c +1 -0
@@ -1145,6 +1145,7 @@ static void ip6_rt_init_dst(struct rt6_info *rt, const struct fib6_result *res) rt->dst.input = ip6_input; }else if (ipv6_addr_type (&f6i->fib6_dst.addr) &IPV6_ADDR_MULTICAST ) { rt->dst.input = ip6_mc_input; + rt->dst.output = ip6_mr_output; }else { rt->dst.input = ip6_forward; }
Signature · 1 line
2.49.0
PATCH v3 11/15 vxlan: Support MC routing in the underlay
In reply to Petr MachataLocally-generated MC packets have so far not been subject to MC routing. Instead an MC-enabled installation would maintain the MC routing tables, and separately from that the list of interfaces to send packets to as part of the VXLAN FDB and MDB.
In a previous patch, a ip_mr_output() and ip6_mr_output() routines were added for IPv4 and IPv6. All locally generated MC traffic is now passed through these functions. For reasons of backward compatibility, an SKB (IPCB / IP6CB) flag guards the actual MC routing.
This patch adds logic to set the flag, and the UAPI to enable the behavior.
---
Notes:
CC: Andrew Lunn <[email protected]>
CC: Menglong Dong <[email protected]>
drivers/net/vxlan/vxlan_core.c | 22 ++++++++++++++++++++-- include/net/vxlan.h | 5 ++++- include/uapi/linux/if_link.h | 1 + 3 files changed, 25 insertions(+), 3 deletions(-)
drivers/net/vxlan/vxlan_core.c +20 -2
@@ -2451,6 +2451,7 @@ void vxlan_xmit_one(struct sk_buff *skb, struct net_device *dev,rcu_read_lock ();if (addr_family ==AF_INET ) {struct vxlan_sock *sock4 =rcu_dereference (vxlan->vn4_sock); +u16 ipcb_flags =0 ;struct rtable *rt;__be16 df =0 ;__be32 saddr;
@@ -2467,6 +2468,9 @@ void vxlan_xmit_one(struct sk_buff *skb, struct net_device *dev, goto tx_error; } +if (flags &VXLAN_F_MC_ROUTE ) + ipcb_flags |=IPSKB_MCROUTE ; +if (!info) {/* Bypass encapsulation if the destination is local */ err = encap_bypass_if_local(skb, dev, vxlan, AF_INET,
@@ -2522,11 +2526,13 @@ void vxlan_xmit_one(struct sk_buff *skb, struct net_device *dev,udp_tunnel_xmit_skb (rt, sock4->sock->sk, skb, saddr, pkey->u.ipv4.dst, tos, ttl, df, - src_port, dst_port, xnet, !udp_sum,0 ); + src_port, dst_port, xnet, !udp_sum, + ipcb_flags);#if IS_ENABLED (CONFIG_IPV6 ) } else {struct vxlan_sock *sock6 =rcu_dereference (vxlan->vn6_sock);struct in6_addr saddr; +u16 ip6cb_flags =0 ;if (!ifindex) ifindex = sock6->sock->sk->sk_bound_dev_if;
@@ -2542,6 +2548,9 @@ void vxlan_xmit_one(struct sk_buff *skb, struct net_device *dev, goto tx_error; } +if (flags &VXLAN_F_MC_ROUTE ) + ip6cb_flags |=IP6SKB_MCROUTE ; +if (!info) {u32 rt6i_flags =dst_rt6_info (ndst)->rt6i_flags;
@@ -2587,7 +2596,7 @@ void vxlan_xmit_one(struct sk_buff *skb, struct net_device *dev,udp_tunnel6_xmit_skb (ndst, sock6->sock->sk, skb, dev, &saddr, &pkey->u.ipv6.dst, tos, ttl, pkey->label, src_port, dst_port, !udp_sum, -0 ); + ip6cb_flags);#endif }vxlan_vnifilter_count (vxlan, vni,NULL ,VXLAN_VNI_STATS_TX , pkt_len);
@@ -3402,6 +3411,7 @@ static const struct nla_policy vxlan_policy[IFLA_VXLAN_MAX + 1] = { [IFLA_VXLAN_LOCALBYPASS] = NLA_POLICY_MAX(NLA_U8, 1), [IFLA_VXLAN_LABEL_POLICY] = NLA_POLICY_MAX(NLA_U32, VXLAN_LABEL_MAX), [IFLA_VXLAN_RESERVED_BITS] = NLA_POLICY_EXACT_LEN(sizeof(struct vxlanhdr)), + [IFLA_VXLAN_MC_ROUTE] = NLA_POLICY_MAX(NLA_U8, 1), }; static int vxlan_validate(struct nlattr *tb[], struct nlattr *data[],
@@ -4315,6 +4325,14 @@ static int vxlan_nl2conf(struct nlattr *tb[], struct nlattr *data[],return err; } +if (data[IFLA_VXLAN_MC_ROUTE ]) { + err =vxlan_nl2flag (conf, data,IFLA_VXLAN_MC_ROUTE , +VXLAN_F_MC_ROUTE , changelink, + true, extack); +if (err) +return err; + } +if (tb[IFLA_MTU ]) {if (changelink) { NL_SET_ERR_MSG_ATTR(extack, tb[IFLA_MTU],
include/net/vxlan.h +4 -1
@@ -332,6 +332,7 @@ struct vxlan_dev {#define VXLAN_F_VNIFILTER 0x20000#define VXLAN_F_MDB 0x40000#define VXLAN_F_LOCALBYPASS 0x80000 +#define VXLAN_F_MC_ROUTE 0x100000/* Flags that are used in the receive path. These flags must match in * order for a socket to be shareable
@@ -353,7 +354,9 @@ struct vxlan_dev { VXLAN_F_UDP_ZERO_CSUM6_RX | \ VXLAN_F_COLLECT_METADATA | \ VXLAN_F_VNIFILTER | \ - VXLAN_F_LOCALBYPASS) + VXLAN_F_LOCALBYPASS | \ + VXLAN_F_MC_ROUTE | \ + 0)struct net_device *vxlan_dev_create (struct net *net,const char *name,u8 name_assign_type,struct vxlan_config *conf);
include/uapi/linux/if_link.h +1 -0
@@ -1398,6 +1398,7 @@ enum {IFLA_VXLAN_LOCALBYPASS ,IFLA_VXLAN_LABEL_POLICY ,/* IPv6 flow label policy; ifla_vxlan_label_policy */ IFLA_VXLAN_RESERVED_BITS , +IFLA_VXLAN_MC_ROUTE , __IFLA_VXLAN_MAX };#define IFLA_VXLAN_MAX (__IFLA_VXLAN_MAX - 1)
Signature · 1 line
2.49.0
PATCH v3 12/15 selftests: forwarding: lib: Move smcrouted helpers here
In reply to Petr Machatarouter_multicast.sh has several helpers for work with smcrouted. Extract them to lib.sh so that other selftests can use them as well. Convert the helpers to defer in the process, because that simplifies the interface quite a bit. Therefore have router_multicast.sh invoke defer_scopes_cleanup() in its cleanup() function.
---
Notes:
v2:
- Adjust as per shellcheck citations
---
CC: Shuah Khan <[email protected]>
CC: [email protected]
tools/testing/selftests/net/forwarding/lib.sh | 33 +++++++++++++++++ .../net/forwarding/router_multicast.sh | 35 ++++--------------- 2 files changed, 39 insertions(+), 29 deletions(-)
tools/testing/selftests/net/forwarding/lib.sh +33 -0
@@ -37,6 +37,7 @@ declare -A NETIFS=( : "${TEAMD:=teamd}" : "${MCD:=smcrouted}" : "${MC_CLI:=smcroutectl}" +: "${MCD_TABLE_NAME:=selftests}" # Constants for netdevice bring-up: # Default time in seconds to wait for an interface to come up before giving up
@@ -1757,6 +1758,38 @@ mc_send() msend -g $groups -I $if_name -c 1 > /dev/null 2>&1 } +adf_mcd_start() +{ + local table_name="$MCD_TABLE_NAME" + local smcroutedir + local pid + local i + + check_command "$MCD" || return 1 + check_command "$MC_CLI" || return 1 + + smcroutedir=$(mktemp -d) + defer rm -rf "$smcroutedir" + + for ((i = 1; i <= NUM_NETIFS; ++i)); do + echo "phyint ${NETIFS[p$i]} enable" >> \ + "$smcroutedir/$table_name.conf" + done + + "$MCD" -N -I "$table_name" -f "$smcroutedir/$table_name.conf" \ + -P "$smcroutedir/$table_name.pid" + busywait "$BUSYWAIT_TIMEOUT" test -e "$smcroutedir/$table_name.pid" + pid=$(cat "$smcroutedir/$table_name.pid") + defer kill_process "$pid" +} + +mc_cli() +{ + local table_name="$MCD_TABLE_NAME" + + "$MC_CLI" -I "$table_name" "$@" +} + start_ip_monitor() { local mtype=$1; shift
tools/testing/selftests/net/forwarding/router_multicast.sh +6 -29
@@ -33,10 +33,6 @@ NUM_NETIFS=6 source lib.sh source tc_common.sh -require_command $MCD -require_command $MC_CLI -table_name=selftests - h1_create() { simple_if_init $h1 198.51.100.2/28 2001:db8:1::2/64
@@ -149,25 +145,6 @@ router_destroy() ip link set dev $rp1 down } -start_mcd() -{ - SMCROUTEDIR="$(mktemp -d)" - - for ((i = 1; i <= $NUM_NETIFS; ++i)); do - echo "phyint ${NETIFS[p$i]} enable" >> \ - $SMCROUTEDIR/$table_name.conf - done - - $MCD -N -I $table_name -f $SMCROUTEDIR/$table_name.conf \ - -P $SMCROUTEDIR/$table_name.pid -} - -kill_mcd() -{ - pkill $MCD - rm -rf $SMCROUTEDIR -} - setup_prepare() { h1=${NETIFS[p1]}
@@ -179,7 +156,7 @@ setup_prepare() rp3=${NETIFS[p5]} h3=${NETIFS[p6]} - start_mcd + adf_mcd_start || exit "$EXIT_STATUS" vrf_prepare
@@ -206,7 +183,7 @@ cleanup() vrf_cleanup - kill_mcd + defer_scopes_cleanup } create_mcast_sg()
@@ -214,9 +191,9 @@ create_mcast_sg() local if_name=$1; shift local s_addr=$1; shift local mcast=$1; shift - local dest_ifs=${@} + local dest_ifs=("${@}") - $MC_CLI -I $table_name add $if_name $s_addr $mcast $dest_ifs + mc_cli add "$if_name" "$s_addr" "$mcast" "${dest_ifs[@]}" } delete_mcast_sg()
@@ -224,9 +201,9 @@ delete_mcast_sg() local if_name=$1; shift local s_addr=$1; shift local mcast=$1; shift - local dest_ifs=${@} + local dest_ifs=("${@}") - $MC_CLI -I $table_name remove $if_name $s_addr $mcast $dest_ifs + mc_cli remove "$if_name" "$s_addr" "$mcast" "${dest_ifs[@]}" } mcast_v4()
Signature · 1 line
2.49.0
PATCH v3 13/15 selftests: net: lib: Add ip_link_has_flag()
In reply to Petr MachataAdd a helper to determine whether a given netdevice has a given flag.
Rewrite ip_link_is_up() in terms of the new helper.
---
Notes:
CC: Shuah Khan <[email protected]>
CC: [email protected]
tools/testing/selftests/net/lib.sh | 12 +++++++++--- 1 file changed, 9 insertions(+), 3 deletions(-)
tools/testing/selftests/net/lib.sh +9 -3
@@ -547,13 +547,19 @@ ip_link_set_addr() defer ip link set dev "$name" address "$old_addr" } -ip_link_is_up() +ip_link_has_flag() { local name=$1; shift + local flag=$1; shift local state=$(ip -j link show "$name" | - jq -r '(.[].flags[] | select(. == "UP")) // "DOWN"') - [[ $state == "UP" ]] + jq --arg flag "$flag" 'any(.[].flags.[]; . == $flag)') + [[ $state == true ]] +} + +ip_link_is_up() +{ + ip_link_has_flag "$1" UP } ip_link_set_up()
Signature · 1 line
2.49.0
PATCH v3 14/15 selftests: forwarding: adf_mcd_start(): Allow configuring custom interfaces
In reply to Petr MachataTests may wish to add other interfaces to listen on. Notably locally generated traffic uses dummy interfaces. The multicast daemon needs to know about these so that it allows forming rules that involve these interfaces, and so that net.ipv4.conf.X.mc_forwarding is set for the interfaces.
To that end, allow passing in a list of interfaces to configure in addition to all the physical ones.
---
Notes:
v2:
- Adjust as per shellcheck citations
- Retain Nik's R-b, the changes were very minor.
---
CC: Shuah Khan <[email protected]>
CC: [email protected]
tools/testing/selftests/net/forwarding/lib.sh | 13 +++++++++++++ 1 file changed, 13 insertions(+)
tools/testing/selftests/net/forwarding/lib.sh +13 -0
@@ -1760,9 +1760,12 @@ mc_send() adf_mcd_start() { + local ifs=("$@") + local table_name="$MCD_TABLE_NAME" local smcroutedir local pid + local if local i check_command "$MCD" || return 1
@@ -1776,6 +1779,16 @@ adf_mcd_start() "$smcroutedir/$table_name.conf" done + for if in "${ifs[@]}"; do + if ! ip_link_has_flag "$if" MULTICAST; then + ip link set dev "$if" multicast on + defer ip link set dev "$if" multicast off + fi + + echo "phyint $if enable" >> \ + "$smcroutedir/$table_name.conf" + done + "$MCD" -N -I "$table_name" -f "$smcroutedir/$table_name.conf" \ -P "$smcroutedir/$table_name.pid" busywait "$BUSYWAIT_TIMEOUT" test -e "$smcroutedir/$table_name.pid"
Signature · 1 line
2.49.0
PATCH v3 15/15 selftests: forwarding: Add a test for verifying VXLAN MC underlay
In reply to Petr MachataAdd tests for MC-routing underlay VXLAN traffic.
---
Notes:
v3:
- Disable shellchecking apparently-unreachable commands. They are actually reachable through tests_run, in_ns, etc.
- Run setup_wait with an explicit argument to avoid shellcheck citation.
v2:
- Adjust as per shellcheck citations
---
CC: Shuah Khan <[email protected]>
CC: [email protected]
.../testing/selftests/net/forwarding/Makefile | 1 + .../net/forwarding/vxlan_bridge_1q_mc_ul.sh | 771 ++++++++++++++++++ 2 files changed, 772 insertions(+) create mode 100755 tools/testing/selftests/net/forwarding/vxlan_bridge_1q_mc_ul.sh
tools/testing/selftests/net/forwarding/Makefile +1 -0
@@ -102,6 +102,7 @@ TEST_PROGS = bridge_fdb_learning_limit.sh \ vxlan_bridge_1d_port_8472.sh \ vxlan_bridge_1d.sh \ vxlan_bridge_1q_ipv6.sh \ + vxlan_bridge_1q_mc_ul.sh \ vxlan_bridge_1q_port_8472_ipv6.sh \ vxlan_bridge_1q_port_8472.sh \ vxlan_bridge_1q.sh \
tools/testing/selftests/net/forwarding/vxlan_bridge_1q_mc_ul.sh new file +771 -0
771 lines not on this page · raw message
Signature · 1 line
2.49.0
This series was applied to netdev/net-next.git (main) by Jakub Kicinski <[email protected]>:
Hello:
This series was applied to netdev/net-next.git (main) by Jakub Kicinski <[email protected]>:
Quoted 8 lines · On Tue, 17 Jun 2025 00:44:08 +0200 you wrote:
Multicast routing is today handled in the input path. Locally generated MC packets don't hit the IPMR code. Thus if a VXLAN remote address is multicast, the driver needs to set an OIF during route lookup. In practice that means that MC routing configuration needs to be kept in sync with the VXLAN FDB and MDB. Ideally, the VXLAN packets would be routed by the MC routing code instead.
[...]
Here is the summary with links:
- [net-next,v3,01/15] net: ipv4: Add a flags argument to iptunnel_xmit(), udp_tunnel_xmit_skb()
https://git.kernel.org/netdev/net-next/c/e3411e326fa4 - [net-next,v3,02/15] net: ipv4: ipmr: ipmr_queue_xmit(): Drop local variable `dev' https://git.kernel.org/netdev/net-next/c/3b7bc938e0ad - [net-next,v3,03/15] net: ipv4: ipmr: Split ipmr_queue_xmit() in two https://git.kernel.org/netdev/net-next/c/b2e653bcff0f - [net-next,v3,04/15] net: ipv4: Add ip_mr_output() https://git.kernel.org/netdev/net-next/c/35bec72a24ac - [net-next,v3,05/15] net: ipv6: Make udp_tunnel6_xmit_skb() void https://git.kernel.org/netdev/net-next/c/6a7d88ca15f7 - [net-next,v3,06/15] net: ipv6: Add a flags argument to ip6tunnel_xmit(), udp_tunnel6_xmit_skb() https://git.kernel.org/netdev/net-next/c/f78c75d84fe8 - [net-next,v3,07/15] net: ipv6: ip6mr: Fix in/out netdev to pass to the FORWARD chain https://git.kernel.org/netdev/net-next/c/3365afd3abda - [net-next,v3,08/15] net: ipv6: ip6mr: Make ip6mr_forward2() void https://git.kernel.org/netdev/net-next/c/094f39d5e84d - [net-next,v3,09/15] net: ipv6: ip6mr: Split ip6mr_forward2() in two https://git.kernel.org/netdev/net-next/c/1b02f4475d29 - [net-next,v3,10/15] net: ipv6: Add ip6_mr_output() https://git.kernel.org/netdev/net-next/c/96e8f5a9fe2d - [net-next,v3,11/15] vxlan: Support MC routing in the underlay https://git.kernel.org/netdev/net-next/c/f8337efa4ff5 - [net-next,v3,12/15] selftests: forwarding: lib: Move smcrouted helpers here https://git.kernel.org/netdev/net-next/c/2a719b7bacc7 - [net-next,v3,13/15] selftests: net: lib: Add ip_link_has_flag() https://git.kernel.org/netdev/net-next/c/4baa1d3a5080 - [net-next,v3,14/15] selftests: forwarding: adf_mcd_start(): Allow configuring custom interfaces https://git.kernel.org/netdev/net-next/c/237f84a6d24a - [net-next,v3,15/15] selftests: forwarding: Add a test for verifying VXLAN MC underlay https://git.kernel.org/netdev/net-next/c/e3180379e2df
You are awesome, thank you!
Signature · 2 lines
Deet-doot-dot, I am a bot. https://korg.docs.kernel.org/patchwork/pwbot.html