i3c: dw-i3c: Enable support for dw-i3c controller NACK retry sysfs and DAT restore fix
Subsystems (2)
v7 cover i3c: dw-i3c: Enable support for dw-i3c controller NACK retry sysfs and DAT restore fix
From: Adrian Ng Ho Yin <[email protected]>
This patch series adds a controller-wide sysfs attribute dev_nack_retry_count for the DesignWare I3C controller, allowing runtime control of the automatic retry mechanism when a device NACKs. Some I3C slave devices may temporarily be busy and unable to respond immediately; automatic retries improve robustness in such cases. Writes are clamped to the hardware maximum of 3, and the value is applied to all active DAT entries.
The series also fixes dw_i3c_master_restore_addrs() to preserve existing DAT entry bits, preventing overwrites during runtime PM resume.
---
changelog:v6->v7
* Update dev_nack_retry_show to remove redundant i3cbus variable.
* Refactor dev_nack_retry_store to store dev_nack_retry val only if set_dev_nack_retry does not return error.
* Update set_dev_nack_retry in master and dw-i3c-master to take additional param which is the dev_nack_retry_cnt.
v6 patch link:
https://lore.kernel.org/all/[email protected]/
v5->v6
* Use dev_to_i3cmaster to get i3cmaster insteasd of direct assignment.
* Remove redundant set_dev_nack_retry callback function check.
* Update kernel doc for set_dev_nack_retry.
* Add macro for dev nack retry mask.
v5 patch link:
https://lore.kernel.org/all/[email protected]/
v4->v5
* Revert changes that made bus_maintenance_lock and bus_maintenance_unlock helpers public.
* Move dev_nack_retry sysfs attribute to master.c; create it only if the master implements the dev_nack_retry callback.
* Add dev_nack_retry field to i3c_master_controller; updates are applied under bus maintenance lock.
* Add optional ops to configure dev_nack_retry in the DAT entry in dw-i3c-master.
v4 patch link:
https://lore.kernel.org/all/[email protected]/
v3->v4
* Make bus_maintenance_lock and bus_maintenance_unlock helpers public.
* Replace taking spinlock during DAT update with bus_maintenance_lock.
* Add macro for static and dynamic addr for device addr table.
* Replace GENMASK calls with the appropriate macros when updating addr table.
v3 patch link:
https://lore.kernel.org/all/[email protected]/
v2->v3
* Update commit message for better clarity
* Update function name to maintain consistency.
* Update store function to return error when retry value exceeds hw limit.
* Add lock to protect DAT to avoid concurrent during transfers.
* Clear the address field in the DAT entry before setting new values to ensure correct dynamic/static address configuration
v2 patch link:
https://lore.kernel.org/all/[email protected]/
v1->v2
* Drop dev_nack_retry_cnt binding and device tree changes.
* Update commit message for better clarity.
* Update to use controller wide sysfs attribute that configures dev_nack_retry_cnt during runtime.
v1 patch link:
https://lore.kernel.org/all/[email protected]/
---
Adrian Ng Ho Yin (5):
i3c: add sysfs entry for Device NACK Retry count
i3c: add sysfs attribute for device NACK retry
i3c: dw: Add support for Device NACK Retry configuration
i3c: dw: use FIELD_PREP for device address table macros
i3c: dw: Preserve DAT entry bits when restoring addresses
Documentation/ABI/testing/sysfs-bus-i3c | 12 +++++ drivers/i3c/master.c | 38 ++++++++++++++++ drivers/i3c/master/dw-i3c-master.c | 59 ++++++++++++++++++++++--- include/linux/i3c/master.h | 6 +++ 4 files changed, 109 insertions(+), 6 deletions(-)
Signature · 1 line
2.49.GIT
PATCH v7 1/5 i3c: add sysfs entry for Device NACK Retry count
From: Adrian Ng Ho Yin <[email protected]>
Document sysfs attribute dev_nack_retry_cnt that controls the number of automatic retries performed by the I3C controller when a target device returns a NACK
--- Documentation/ABI/testing/sysfs-bus-i3c | 12 ++++++++++++ 1 file changed, 12 insertions(+)
Documentation/ABI/testing/sysfs-bus-i3c +12 -0
@@ -161,3 +161,15 @@ Contact: [email protected] Description: These directories are just symbolic links to /sys/bus/i3c/devices/i3c-<bus-id>/<bus-id>-<device-pid>. + +What: /sys/bus/i3c/devices/i3c-<bus-id>/<bus-id>-<device-pid>/dev_nack_retry_count +KernelVersion: 6.18 +Contact: [email protected] +Description: + Expose the dev_nak_retry_count which controls the number of + automatic retries that will be performed by the controller when + the target device returns a NACK response. A value of 0 disables + the automatic retries. A max value of 3 can be configured. Exist + only when I3C constroller supports this retry on nack feature. + + Valid values: 0-3
Signature · 1 line
2.49.GIT
Alexandre Belloni
maintainerRe: [PATCH v7 1/5] i3c: add sysfs entry for Device NACK Retry count
Quoted 6 lines · On 08/12/2025 15:11:16+0800, [email protected] wrote:
From: Adrian Ng Ho Yin <[email protected]>
Document sysfs attribute
dev_nack_retry_cntthat controls the number of automatic retries performed by the I3C controller when a target device returns a NACK
Quoted 6 lines
Signed-off-by Adrian Ng Ho Yin <[email protected]>Reviewed-by Frank Li <[email protected]>--- Documentation/ABI/testing/sysfs-bus-i3c | 12 ++++++++++++ 1 file changed, 12 insertions(+)
Please squash 1/5 and 2/5.
Quoted 23 lines
Documentation/ABI/testing/sysfs-bus-i3c +12
-0@@ -161,3 +161,15 @@ Contact: [email protected] Description: These directories are just symbolic links to /sys/bus/i3c/devices/i3c-<bus-id>/<bus-id>-<device-pid>. + +What: /sys/bus/i3c/devices/i3c-<bus-id>/<bus-id>-<device-pid>/dev_nack_retry_count +KernelVersion: 6.18 +Contact: [email protected] +Description: + Expose the dev_nak_retry_count which controls the number of + automatic retries that will be performed by the controller when + the target device returns a NACK response. A value of 0 disables + the automatic retries. A max value of 3 can be configured. Exist + only when I3C constroller supports this retry on nack feature. + + Valid values: 0-3Signature · 1 line
2.49.GIT
Signature · 3 lines
Alexandre Belloni, co-owner and COO, Bootlin Embedded Linux and Kernel engineering https://bootlin.com
PATCH v7 2/5 i3c: add sysfs attribute for device NACK retry
In reply to [email protected]From: Adrian Ng Ho Yin <[email protected]>
Add a dev_nack_retry sysfs attribute to allow reading and updating the device NACK retry count. A new dev_nack_retry field and an optional set_dev_nack_retry() callback are added to i3c_master_controller. The attribute is created only when the callback is implemented.
Updates are applied under the I3C bus maintenance lock to ensure safe hardware reconfiguration.
--- drivers/i3c/master.c | 38 ++++++++++++++++++++++++++++++++++++++ include/linux/i3c/master.h | 6 ++++++ 2 files changed, 44 insertions(+)
drivers/i3c/master.c +38 -0
@@ -685,6 +685,38 @@ static ssize_t hotjoin_show(struct device *dev, struct device_attribute *da, chastatic DEVICE_ATTR_RW (hotjoin); +static ssize_t dev_nack_retry_show (struct device *dev,struct device_attribute *attr, +char *buf) +{ +return sysfs_emit (buf,"%u\n" ,dev_to_i3cmaster (dev)->dev_nack_retry); +} + +static ssize_t dev_nack_retry_store (struct device *dev,struct device_attribute *attr, +const char *buf,size_t count) +{ +struct i3c_bus *i3cbus =dev_to_i3cbus (dev); +struct i3c_master_controller *master =dev_to_i3cmaster (dev); +unsigned long val; +int ret; + + ret =kstrtoul (buf,0 , &val); +if (ret) +return ret; + +i3c_bus_maintenance_lock (i3cbus); + ret = master->ops->set_dev_nack_retry (master, val); +i3c_bus_maintenance_unlock (i3cbus); + +if (ret) +return ret; + + master->dev_nack_retry = val; + +return count; +} + +static DEVICE_ATTR_RW (dev_nack_retry); +static struct attribute *i3c_masterdev_attrs[] = { &dev_attr_mode.attr, &dev_attr_current_master.attr,
@@ -2962,6 +2994,9 @@ int i3c_master_register(struct i3c_master_controller *master,i3c_master_register_new_i3c_devs (master);i3c_bus_normaluse_unlock (&master->bus); +if (master->ops->set_dev_nack_retry) +device_create_file (&master->dev, &dev_attr_dev_nack_retry); +return 0 ; err_del_dev:
@@ -2987,6 +3022,9 @@ void i3c_master_unregister(struct i3c_master_controller *master) {i3c_bus_notify (&master->bus,I3C_NOTIFY_BUS_REMOVE ); +if (master->ops->set_dev_nack_retry) +device_remove_file (&master->dev, &dev_attr_dev_nack_retry); +i3c_master_i2c_adapter_cleanup (master);i3c_master_unregister_i3c_devs (master);i3c_master_bus_cleanup (master);
include/linux/i3c/master.h +6 -0
@@ -462,6 +462,8 @@ struct i3c_bus {* @enable_hotjoin: enable hot join event detect. * @disable_hotjoin: disable hot join event detect. * @set_speed: adjust I3C open drain mode timing. +* @set_dev_nack_retry: configure device NACK retry count for the master +* controller. */ struct i3c_master_controller_ops {int (*bus_init)(struct i3c_master_controller *master);
@@ -491,6 +493,8 @@ struct i3c_master_controller_ops {int (*enable_hotjoin)(struct i3c_master_controller *master);int (*disable_hotjoin)(struct i3c_master_controller *master);int (*set_speed)(struct i3c_master_controller *master,enum i3c_open_drain_speed speed); +int (*set_dev_nack_retry)(struct i3c_master_controller *master, +unsigned long dev_nack_retry_cnt); };/**
@@ -510,6 +514,7 @@ struct i3c_master_controller_ops {* @boardinfo: board-level information attached to devices connected on the bus * @bus: I3C bus exposed by this master * @wq: workqueue which can be used by master +* @dev_nack_retry: retry count when slave device nack * drivers if they need to postpone operations that need to take place * in a thread context. Typical examples are Hot Join processing which * requires taking the bus lock in maintenance, which in turn, can only
@@ -534,6 +539,7 @@ struct i3c_master_controller { } boardinfo;struct i3c_bus bus;struct workqueue_struct *wq; +unsigned int dev_nack_retry; };/**
Signature · 1 line
2.49.GIT
Re: [PATCH v7 2/5] i3c: add sysfs attribute for device NACK retry
Quoted 7 lines · On Mon, Dec 08, 2025 at 03:11:17PM +0800, [email protected] wrote:
From: Adrian Ng Ho Yin <[email protected]>
Add a
dev_nack_retrysysfs attribute to allow reading and updating the device NACK retry count. A newdev_nack_retryfield and an optionalset_dev_nack_retry()callback are added toi3c_master_controller. The attribute is created only when the callback is implemented.
Quoted 5 lines
Updates are applied under the I3C bus maintenance lock to ensure safe hardware reconfiguration.
Signed-off-by Adrian Ng Ho Yin <[email protected]>---
Quoted 108 lines
drivers/i3c/master.c | 38 ++++++++++++++++++++++++++++++++++++++ include/linux/i3c/master.h | 6 ++++++ 2 files changed, 44 insertions(+)drivers/i3c/master.c +38
-0@@ -685,6 +685,38 @@ static ssize_t hotjoin_show(struct device *dev, struct device_attribute *da, chastatic DEVICE_ATTR_RW (hotjoin); +static ssize_t dev_nack_retry_show (struct device *dev,struct device_attribute *attr, +char *buf) +{ +return sysfs_emit (buf,"%u\n" ,dev_to_i3cmaster (dev)->dev_nack_retry); +} + +static ssize_t dev_nack_retry_store (struct device *dev,struct device_attribute *attr, +const char *buf,size_t count) +{ +struct i3c_bus *i3cbus =dev_to_i3cbus (dev); +struct i3c_master_controller *master =dev_to_i3cmaster (dev); +unsigned long val; +int ret; + + ret =kstrtoul (buf,0 , &val); +if (ret) +return ret; + +i3c_bus_maintenance_lock (i3cbus); + ret = master->ops->set_dev_nack_retry (master, val); +i3c_bus_maintenance_unlock (i3cbus); + +if (ret) +return ret; + + master->dev_nack_retry = val; + +return count; +} + +static DEVICE_ATTR_RW (dev_nack_retry); +static struct attribute *i3c_masterdev_attrs[] = { &dev_attr_mode.attr, &dev_attr_current_master.attr,@@ -2962,6 +2994,9 @@ int i3c_master_register(struct i3c_master_controller *master,i3c_master_register_new_i3c_devs (master);i3c_bus_normaluse_unlock (&master->bus); +if (master->ops->set_dev_nack_retry) +device_create_file (&master->dev, &dev_attr_dev_nack_retry); +return 0 ; err_del_dev:@@ -2987,6 +3022,9 @@ void i3c_master_unregister(struct i3c_master_controller *master) {i3c_bus_notify (&master->bus,I3C_NOTIFY_BUS_REMOVE ); +if (master->ops->set_dev_nack_retry) +device_remove_file (&master->dev, &dev_attr_dev_nack_retry); +i3c_master_i2c_adapter_cleanup (master);i3c_master_unregister_i3c_devs (master);i3c_master_bus_cleanup (master);include/linux/i3c/master.h +6
-1@@ -462,6 +462,8 @@ struct i3c_bus {* @enable_hotjoin: enable hot join event detect. * @disable_hotjoin: disable hot join event detect. * @set_speed: adjust I3C open drain mode timing. +* @set_dev_nack_retry: configure device NACK retry count for the master +* controller. */ struct i3c_master_controller_ops {int (*bus_init)(struct i3c_master_controller *master);@@ -491,6 +493,8 @@ struct i3c_master_controller_ops {int (*enable_hotjoin)(struct i3c_master_controller *master);int (*disable_hotjoin)(struct i3c_master_controller *master);int (*set_speed)(struct i3c_master_controller *master,enum i3c_open_drain_speed speed); +int (*set_dev_nack_retry)(struct i3c_master_controller *master, +unsigned long dev_nack_retry_cnt); };/** @@ -510,6 +514,7 @@ struct i3c_master_controller_ops {* @boardinfo: board-level information attached to devices connected on the bus * @bus: I3C bus exposed by this master * @wq: workqueue which can be used by master +* @dev_nack_retry: retry count when slave device nack * drivers if they need to postpone operations that need to take place * in a thread context. Typical examples are Hot Join processing which * requires taking the bus lock in maintenance, which in turn, can only @@ -534,6 +539,7 @@ struct i3c_master_controller { } boardinfo;struct i3c_bus bus;struct workqueue_struct *wq; +unsigned int dev_nack_retry; };/** -- 2.49.GIT
Alexandre Belloni
maintainerRe: [PATCH v7 2/5] i3c: add sysfs attribute for device NACK retry
In reply to [email protected]Quoted 45 lines · On 08/12/2025 15:11:17+0800, [email protected] wrote:
From: Adrian Ng Ho Yin <[email protected]>
Add a
dev_nack_retrysysfs attribute to allow reading and updating the device NACK retry count. A newdev_nack_retryfield and an optionalset_dev_nack_retry()callback are added toi3c_master_controller. The attribute is created only when the callback is implemented.Updates are applied under the I3C bus maintenance lock to ensure safe hardware reconfiguration.
Signed-off-by Adrian Ng Ho Yin <[email protected]>--- drivers/i3c/master.c | 38 ++++++++++++++++++++++++++++++++++++++ include/linux/i3c/master.h | 6 ++++++ 2 files changed, 44 insertions(+)drivers/i3c/master.c +21
-0@@ -685,6 +685,38 @@ static ssize_t hotjoin_show(struct device *dev, struct device_attribute *da, chastatic DEVICE_ATTR_RW (hotjoin); +static ssize_t dev_nack_retry_show (struct device *dev,struct device_attribute *attr, +char *buf) +{ +return sysfs_emit (buf,"%u\n" ,dev_to_i3cmaster (dev)->dev_nack_retry); +} + +static ssize_t dev_nack_retry_store (struct device *dev,struct device_attribute *attr, +const char *buf,size_t count) +{ +struct i3c_bus *i3cbus =dev_to_i3cbus (dev); +struct i3c_master_controller *master =dev_to_i3cmaster (dev); +unsigned long val; +int ret; + + ret =kstrtoul (buf,0 , &val); +if (ret) +return ret; + +i3c_bus_maintenance_lock (i3cbus); + ret = master->ops->set_dev_nack_retry (master, val); +i3c_bus_maintenance_unlock (i3cbus);
drivers/i3c/master.c static ssize_t hotjoin_show(struct device *dev, struct device_attribute *da, cha · line 718
Quoted 10 lines
drivers/i3c/master.c +10
-0+ +if (ret) +return ret; + + master->dev_nack_retry = val; + +return count; +} + +static DEVICE_ATTR_RW (dev_nack_retry);
Shouldn't that be dev_nack_retry_count ?
Quoted 65 lines
drivers/i3c/master.c +7
-0+static struct attribute *i3c_masterdev_attrs[] = { &dev_attr_mode.attr, &dev_attr_current_master.attr,@@ -2962,6 +2994,9 @@ int i3c_master_register(struct i3c_master_controller *master,i3c_master_register_new_i3c_devs (master);i3c_bus_normaluse_unlock (&master->bus); +if (master->ops->set_dev_nack_retry) +device_create_file (&master->dev, &dev_attr_dev_nack_retry); +return 0 ; err_del_dev:@@ -2987,6 +3022,9 @@ void i3c_master_unregister(struct i3c_master_controller *master) {i3c_bus_notify (&master->bus,I3C_NOTIFY_BUS_REMOVE ); +if (master->ops->set_dev_nack_retry) +device_remove_file (&master->dev, &dev_attr_dev_nack_retry); +i3c_master_i2c_adapter_cleanup (master);i3c_master_unregister_i3c_devs (master);i3c_master_bus_cleanup (master);include/linux/i3c/master.h +6
-0@@ -462,6 +462,8 @@ struct i3c_bus {* @enable_hotjoin: enable hot join event detect. * @disable_hotjoin: disable hot join event detect. * @set_speed: adjust I3C open drain mode timing. +* @set_dev_nack_retry: configure device NACK retry count for the master +* controller. */ struct i3c_master_controller_ops {int (*bus_init)(struct i3c_master_controller *master);@@ -491,6 +493,8 @@ struct i3c_master_controller_ops {int (*enable_hotjoin)(struct i3c_master_controller *master);int (*disable_hotjoin)(struct i3c_master_controller *master);int (*set_speed)(struct i3c_master_controller *master,enum i3c_open_drain_speed speed); +int (*set_dev_nack_retry)(struct i3c_master_controller *master, +unsigned long dev_nack_retry_cnt); };/** @@ -510,6 +514,7 @@ struct i3c_master_controller_ops {* @boardinfo: board-level information attached to devices connected on the bus * @bus: I3C bus exposed by this master * @wq: workqueue which can be used by master +* @dev_nack_retry: retry count when slave device nack * drivers if they need to postpone operations that need to take place * in a thread context. Typical examples are Hot Join processing which * requires taking the bus lock in maintenance, which in turn, can only @@ -534,6 +539,7 @@ struct i3c_master_controller { } boardinfo;struct i3c_bus bus;struct workqueue_struct *wq; +unsigned int dev_nack_retry; };/** Signature · 1 line
2.49.GIT
Signature · 3 lines
Alexandre Belloni, co-owner and COO, Bootlin Embedded Linux and Kernel engineering https://bootlin.com
PATCH v7 3/5 i3c: dw: Add support for Device NACK Retry configuration
In reply to [email protected]From: Adrian Ng Ho Yin <[email protected]>
The DesignWare I3C controller supports automatically retrying transactions when a device NACKs. This is useful for slave devices that may be temporarily busy and not ready to respond immediately.
Add new ops to configure all active DAT entry with dev_nack_retry during runtime. Returns error when value exceeds hw specified limit.
--- drivers/i3c/master/dw-i3c-master.c | 40 ++++++++++++++++++++++++++++++ 1 file changed, 40 insertions(+)
drivers/i3c/master/dw-i3c-master.c +40 -0
@@ -5,6 +5,7 @@* Author: Vitor Soares <[email protected]> */ +#include <linux/bitfield.h> #include <linux/bitops.h> #include <linux/clk.h> #include <linux/completion.h>
@@ -204,8 +205,12 @@#define EXTENDED_CAPABILITY 0xe8#define SLAVE_CONFIG 0xec +#define DW_I3C_DEV_NACK_RETRY_CNT_MAX 0x3 +#define DEV_ADDR_TABLE_DEV_NACK_RETRY_MASK GENMASK(30, 29)#define DEV_ADDR_TABLE_IBI_MDB BIT(12)#define DEV_ADDR_TABLE_SIR_REJECT BIT(13) +#define DEV_ADDR_TABLE_DEV_NACK_RETRY_CNT (x) \ + FIELD_PREP(DEV_ADDR_TABLE_DEV_NACK_RETRY_MASK, (x))#define DEV_ADDR_TABLE_LEGACY_I2C_DEV BIT(31)#define DEV_ADDR_TABLE_DYNAMIC_ADDR (x) (((x) << 16) & GENMASK(23, 16))#define DEV_ADDR_TABLE_STATIC_ADDR (x) ((x) & GENMASK(6, 0))
@@ -1484,6 +1489,40 @@ static irqreturn_t dw_i3c_master_irq_handler(int irq, void *dev_id)return IRQ_HANDLED ; } +static int dw_i3c_master_set_dev_nack_retry (struct i3c_master_controller *m, +unsigned long dev_nack_retry_cnt) +{ +struct dw_i3c_master *master =to_dw_i3c_master (m); +u32 reg; +int i; + +if (dev_nack_retry_cnt >DW_I3C_DEV_NACK_RETRY_CNT_MAX ) { +dev_err (&master->base.dev, +"Value %ld exceeds maximum %d\n" , + dev_nack_retry_cnt,DW_I3C_DEV_NACK_RETRY_CNT_MAX ); +return -ERANGE ; + } + +/* +* Update DAT entries for all currently attached devices. +* We directly iterate through the master's device array. +*/ +for (i =0 ; i < master->maxdevs; i++) { +/* Skip free/empty slots */ +if (master->free_pos &BIT (i)) +continue ; + + reg =readl (master->regs + +DEV_ADDR_TABLE_LOC (master->datstartaddr, i)); + reg &= ~DEV_ADDR_TABLE_DEV_NACK_RETRY_MASK ; + reg |=DEV_ADDR_TABLE_DEV_NACK_RETRY_CNT (dev_nack_retry_cnt); +writel (reg, master->regs + +DEV_ADDR_TABLE_LOC (master->datstartaddr, i)); + } + +return 0 ; +} +static const struct i3c_master_controller_ops dw_mipi_i3c_ops = { .bus_init = dw_i3c_master_bus_init, .bus_cleanup = dw_i3c_master_bus_cleanup,
@@ -1504,6 +1543,7 @@ static const struct i3c_master_controller_ops dw_mipi_i3c_ops = { .recycle_ibi_slot = dw_i3c_master_recycle_ibi_slot, .enable_hotjoin = dw_i3c_master_enable_hotjoin, .disable_hotjoin = dw_i3c_master_disable_hotjoin, + .set_dev_nack_retry = dw_i3c_master_set_dev_nack_retry, };/* default platform ops implementations */
Signature · 1 line
2.49.GIT
Re: [PATCH v7 3/5] i3c: dw: Add support for Device NACK Retry configuration
Quoted 6 lines · On Mon, Dec 08, 2025 at 03:11:18PM +0800, [email protected] wrote:
From: Adrian Ng Ho Yin <[email protected]>
The DesignWare I3C controller supports automatically retrying transactions when a device NACKs. This is useful for slave devices that may be temporarily busy and not ready to respond immediately.
Quoted 6 lines
Add new ops to configure all active DAT entry with
dev_nack_retryduring runtime. Returns error when value exceeds hw specified limit.Signed-off-by Adrian Ng Ho Yin <[email protected]>--- drivers/i3c/master/dw-i3c-master.c | 40 ++++++++++++++++++++++++++++++
Quoted 79 lines
1 file changed, 40 insertions(+)drivers/i3c/master/dw-i3c-master.c +40
-1@@ -5,6 +5,7 @@* Author: Vitor Soares <[email protected]> */ +#include <linux/bitfield.h> #include <linux/bitops.h> #include <linux/clk.h> #include <linux/completion.h> @@ -204,8 +205,12 @@#define EXTENDED_CAPABILITY 0xe8#define SLAVE_CONFIG 0xec +#define DW_I3C_DEV_NACK_RETRY_CNT_MAX 0x3 +#define DEV_ADDR_TABLE_DEV_NACK_RETRY_MASK GENMASK(30, 29)#define DEV_ADDR_TABLE_IBI_MDB BIT(12)#define DEV_ADDR_TABLE_SIR_REJECT BIT(13) +#define DEV_ADDR_TABLE_DEV_NACK_RETRY_CNT (x) \ + FIELD_PREP(DEV_ADDR_TABLE_DEV_NACK_RETRY_MASK, (x))#define DEV_ADDR_TABLE_LEGACY_I2C_DEV BIT(31)#define DEV_ADDR_TABLE_DYNAMIC_ADDR (x) (((x) << 16) & GENMASK(23, 16))#define DEV_ADDR_TABLE_STATIC_ADDR (x) ((x) & GENMASK(6, 0))@@ -1484,6 +1489,40 @@ static irqreturn_t dw_i3c_master_irq_handler(int irq, void *dev_id)return IRQ_HANDLED ; } +static int dw_i3c_master_set_dev_nack_retry (struct i3c_master_controller *m, +unsigned long dev_nack_retry_cnt) +{ +struct dw_i3c_master *master =to_dw_i3c_master (m); +u32 reg; +int i; + +if (dev_nack_retry_cnt >DW_I3C_DEV_NACK_RETRY_CNT_MAX ) { +dev_err (&master->base.dev, +"Value %ld exceeds maximum %d\n" , + dev_nack_retry_cnt,DW_I3C_DEV_NACK_RETRY_CNT_MAX ); +return -ERANGE ; + } + +/* +* Update DAT entries for all currently attached devices. +* We directly iterate through the master's device array. +*/ +for (i =0 ; i < master->maxdevs; i++) { +/* Skip free/empty slots */ +if (master->free_pos &BIT (i)) +continue ; + + reg =readl (master->regs + +DEV_ADDR_TABLE_LOC (master->datstartaddr, i)); + reg &= ~DEV_ADDR_TABLE_DEV_NACK_RETRY_MASK ; + reg |=DEV_ADDR_TABLE_DEV_NACK_RETRY_CNT (dev_nack_retry_cnt); +writel (reg, master->regs + +DEV_ADDR_TABLE_LOC (master->datstartaddr, i)); + } + +return 0 ; +} +static const struct i3c_master_controller_ops dw_mipi_i3c_ops = { .bus_init = dw_i3c_master_bus_init, .bus_cleanup = dw_i3c_master_bus_cleanup,@@ -1504,6 +1543,7 @@ static const struct i3c_master_controller_ops dw_mipi_i3c_ops = { .recycle_ibi_slot = dw_i3c_master_recycle_ibi_slot, .enable_hotjoin = dw_i3c_master_enable_hotjoin, .disable_hotjoin = dw_i3c_master_disable_hotjoin, + .set_dev_nack_retry = dw_i3c_master_set_dev_nack_retry, };/* default platform ops implementations */ --2.49.GIT
PATCH v7 4/5 i3c: dw: use FIELD_PREP for device address table macros
In reply to [email protected]From: Adrian Ng Ho Yin <[email protected]>
Add DEV_ADDR_TABLE_DYNAMIC_MASK / DEV_ADDR_TABLE_DYNAMIC_ADDR(x) for dynamic device addresses and DEV_ADDR_TABLE_STATIC_MASK / DEV_ADDR_TABLE_STATIC_ADDR(x) for static device addresses in the I3C address table. Replace manual shift-and-mask with FIELD_PREP() for both dynamic and static addresses for clarity and maintainability.
--- drivers/i3c/master/dw-i3c-master.c | 6 ++++-- 1 file changed, 4 insertions(+), 2 deletions(-)
drivers/i3c/master/dw-i3c-master.c +4 -2
@@ -207,13 +207,15 @@#define DW_I3C_DEV_NACK_RETRY_CNT_MAX 0x3#define DEV_ADDR_TABLE_DEV_NACK_RETRY_MASK GENMASK(30, 29) +#define DEV_ADDR_TABLE_DYNAMIC_MASK GENMASK(23, 16) +#define DEV_ADDR_TABLE_STATIC_MASK GENMASK(6, 0)#define DEV_ADDR_TABLE_IBI_MDB BIT(12)#define DEV_ADDR_TABLE_SIR_REJECT BIT(13)#define DEV_ADDR_TABLE_DEV_NACK_RETRY_CNT (x) \ FIELD_PREP(DEV_ADDR_TABLE_DEV_NACK_RETRY_MASK, (x))#define DEV_ADDR_TABLE_LEGACY_I2C_DEV BIT(31) -#define DEV_ADDR_TABLE_DYNAMIC_ADDR (x) (((x) << 16) & GENMASK(23, 16)) -#define DEV_ADDR_TABLE_STATIC_ADDR (x) ((x) & GENMASK(6, 0)) +#define DEV_ADDR_TABLE_DYNAMIC_ADDR (x) FIELD_PREP(DEV_ADDR_TABLE_DYNAMIC_MASK, x) +#define DEV_ADDR_TABLE_STATIC_ADDR (x) FIELD_PREP(DEV_ADDR_TABLE_STATIC_MASK, x)#define DEV_ADDR_TABLE_LOC (start, idx) ((start) + ((idx) << 2))#define I3C_BUS_SDR1_SCL_RATE 8000000
Signature · 1 line
2.49.GIT
PATCH v7 5/5 i3c: dw: Preserve DAT entry bits when restoring addresses
In reply to [email protected]From: Adrian Ng Ho Yin <[email protected]>
Update dw_i3c_master_restore_addrs() to preserve existing bits in each Device Address Table (DAT) entry when restoring addresses. This prevents overwriting configuration bits during PM runtime resumes.
--- drivers/i3c/master/dw-i3c-master.c | 13 +++++++++---- 1 file changed, 9 insertions(+), 4 deletions(-)
drivers/i3c/master/dw-i3c-master.c +9 -4
@@ -1696,11 +1696,16 @@ static void dw_i3c_master_restore_addrs(struct dw_i3c_master *master)if (master->free_pos &BIT (pos))continue ; -if (master->devs[pos].is_i2c_addr) - reg_val =DEV_ADDR_TABLE_LEGACY_I2C_DEV | + reg_val =readl (master->regs +DEV_ADDR_TABLE_LOC (master->datstartaddr, pos)); + +if (master->devs[pos].is_i2c_addr) { + reg_val &= ~DEV_ADDR_TABLE_STATIC_MASK ; + reg_val |=DEV_ADDR_TABLE_LEGACY_I2C_DEV |DEV_ADDR_TABLE_STATIC_ADDR (master->devs[pos].addr); -else - reg_val =DEV_ADDR_TABLE_DYNAMIC_ADDR (master->devs[pos].addr); + }else { + reg_val &= ~DEV_ADDR_TABLE_DYNAMIC_MASK ; + reg_val |=DEV_ADDR_TABLE_DYNAMIC_ADDR (master->devs[pos].addr); + }writel (reg_val, master->regs +DEV_ADDR_TABLE_LOC (master->datstartaddr, pos)); }
Signature · 1 line
2.49.GIT