net: dsa: initial support for MaxLinear MxL862xx switches
Subsystems (6)
Daniel Golle
maintainerv4 cover net: dsa: initial support for MaxLinear MxL862xx switches
Hi,
This series adds very basic DSA support for the MaxLinear MxL86252 (5 PHY ports) and MxL86282 (8 PHY ports) switches. The intent is to validate and get feedback on the overall approach and driver structure, especially the firmware-mediated host interface.
MxL862xx integrates a firmware running on an embedded processor (Zephyr RTOS). Host interaction uses a simple API transported over MDIO/MMD. This series includes only what's needed to pass traffic between user ports and the CPU port: relayed MDIO to internal PHYs, basic port enable/disable, and CPU-port special tagging.
At this point the driver does NOT configure any bridges and bridge ports, so isolation of the userports depends on the pre-configuration stored on the flash chip attached to the switch IC. There is an ongoing debate with MaxLinear on how to improve this and make sure the switch is always in a well-defined condition (ie. all ports isolated in individual bridges, learning disabled, and not depending on attached pre-configuration) after reset.
As meanwhile a lot has been improved since RFC v3 it'd still be nice to have some eyes look at this.
Changes since RFC v3
1/4 dt-bindings: net: dsa: add MaxLinear MxL862xx
* remove labels from example
* remove 'bindings for' from commit title
2/4 net: dsa: add tag format for MxL862xx switches
* describe fields and variables with comments
* sub-interface is only 5 bits
* harmonize Kconfig symbol name
* maintain alphabetic order in Kconfig
* fix typo s/beginnig/beginning/
* fix typo s/swtiches/switches/
* arrange local variables in reverse xmas tree order
3/4 net: mdio: add unlocked mdiodev C45 bus accessors
* unchanged
4/4 net: dsa: add basic initial driver for MxL862xx switches
* poll switch readiness after reset
* implement driver shutdown
* added port_fast_aging API call and driver op
* unified port setup in new .port_setup op
* improve comment explaining special handlign for unaligned API read
* various typos and formatting improvements
Changes since RFC v2
1/4, 2/4, 3/4: unchanged
4/4 net: dsa: add basic initial driver for MxL862xx switches
* fix return value being uninitialized on error in mxl862xx_api_wrap()
* add missing description in kerneldoc comment of
struct mxl862xx_ss_sp_tag
Changes since initial RFC
1/4 dt-bindings: net: dsa: add bindings for MaxLinear MxL862xx
* better description in dt-bindings doc
2/4 net: dsa: add tag formats for MxL862xx switches
* make sure all tag fields are initialized
3/4 net: mdio: add unlocked mdiodev C45 bus accessors
* new patch
4/4 net: dsa: add basic initial driver for MxL862xx switches
* make use of struct mdio_device
* add phylink_mac_ops stubs
* drop leftover nonsense from mxl862xx_phylink_get_caps()
* fix endian conversions
* use __le32 instead of enum types in over-the-wire structs
* use existing MDIO_* macros whenever possible
* simplify API constants to be more readable
* use readx_poll_timeout instead of open-coding poll timeout loop
* add mxl862xx_reg_read() and mxl862xx_reg_write() helpers
* demystify error codes returned by the firmware
* add #defines for mxl862xx_ss_sp_tag member values
* move reset to dedicated function, clarify magic number being the reset command ID
Daniel Golle (4):
dt-bindings: net: dsa: add MaxLinear MxL862xx
net: dsa: add tag format for MxL862xx switches
net: mdio: add unlocked mdiodev C45 bus accessors
net: dsa: add basic initial driver for MxL862xx switches
.../bindings/net/dsa/maxlinear,mxl862xx.yaml | 154 +++++++ MAINTAINERS | 8 + drivers/net/dsa/Kconfig | 2 + drivers/net/dsa/Makefile | 1 + drivers/net/dsa/mxl862xx/Kconfig | 12 + drivers/net/dsa/mxl862xx/Makefile | 3 + drivers/net/dsa/mxl862xx/mxl862xx-api.h | 177 ++++++++ drivers/net/dsa/mxl862xx/mxl862xx-cmd.h | 32 ++ drivers/net/dsa/mxl862xx/mxl862xx-host.c | 230 ++++++++++ drivers/net/dsa/mxl862xx/mxl862xx-host.h | 5 + drivers/net/dsa/mxl862xx/mxl862xx.c | 428 ++++++++++++++++++ drivers/net/dsa/mxl862xx/mxl862xx.h | 24 + include/linux/mdio.h | 13 + include/net/dsa.h | 2 + net/dsa/Kconfig | 7 + net/dsa/Makefile | 1 + net/dsa/tag_mxl862xx.c | 128 ++++++ 17 files changed, 1227 insertions(+) create mode 100644 Documentation/devicetree/bindings/net/dsa/maxlinear,mxl862xx.yaml create mode 100644 drivers/net/dsa/mxl862xx/Kconfig create mode 100644 drivers/net/dsa/mxl862xx/Makefile create mode 100644 drivers/net/dsa/mxl862xx/mxl862xx-api.h create mode 100644 drivers/net/dsa/mxl862xx/mxl862xx-cmd.h create mode 100644 drivers/net/dsa/mxl862xx/mxl862xx-host.c create mode 100644 drivers/net/dsa/mxl862xx/mxl862xx-host.h create mode 100644 drivers/net/dsa/mxl862xx/mxl862xx.c create mode 100644 drivers/net/dsa/mxl862xx/mxl862xx.h create mode 100644 net/dsa/tag_mxl862xx.c
Signature · 1 line
2.52.0
Daniel Golle
maintainerRFC PATCH v4 1/4 dt-bindings: net: dsa: add MaxLinear MxL862xx
Add documentation and an example for MaxLinear MxL86282 and MxL86252 switches.
---
RFC v4:
* remove labels from example
* remove 'bindings for' from commit title
RFC v3: no changes
RFC v2: better description in dt-bindings doc
--- .../bindings/net/dsa/maxlinear,mxl862xx.yaml | 154 ++++++++++++++++++ MAINTAINERS | 6 + 2 files changed, 160 insertions(+) create mode 100644 Documentation/devicetree/bindings/net/dsa/maxlinear,mxl862xx.yaml
Documentation/devicetree/bindings/net/dsa/maxlinear,mxl862xx.yaml new file +154 -0
@@ -0,0 +1,154 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/dsa/maxlinear,mxl862xx.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: MaxLinear MxL862xx Ethernet Switch Family + +maintainers: + - Daniel Golle <[email protected]> + +description: + The MaxLinear MxL862xx switch family are multi-port Ethernet switches with + integrated 2.5GE PHYs. The MxL86252 has five PHY ports and the MxL86282 + has eight PHY ports. Both models come with two 10 Gigabit/s SerDes + interfaces to be used to connect external PHYs or SFP cages, or as CPU + port. + +allOf: + - $ref: dsa.yaml#/$defs/ethernet-ports + +properties: + compatible: + enum: + - maxlinear,mxl86252 + - maxlinear,mxl86282 + + reg: + maxItems: 1 + description: MDIO address of the switch + + mdio: + $ref: /schemas/net/mdio.yaml# + unevaluatedProperties: false + +required: + - compatible + - reg + +unevaluatedProperties: false + +examples: + - | + mdio { + #address-cells = <1>; + #size-cells = <0>; + + switch@0 { + compatible = "maxlinear,mxl86282"; + reg = <0>; + + ethernet-ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + phy-handle = <&phy0>; + phy-mode = "internal"; + }; + + port@1 { + reg = <1>; + phy-handle = <&phy1>; + phy-mode = "internal"; + }; + + port@2 { + reg = <2>; + phy-handle = <&phy2>; + phy-mode = "internal"; + }; + + port@3 { + reg = <3>; + phy-handle = <&phy3>; + phy-mode = "internal"; + }; + + port@4 { + reg = <4>; + phy-handle = <&phy4>; + phy-mode = "internal"; + }; + + port@5 { + reg = <5>; + phy-handle = <&phy5>; + phy-mode = "internal"; + }; + + port@6 { + reg = <6>; + phy-handle = <&phy6>; + phy-mode = "internal"; + }; + + port@7 { + reg = <7>; + phy-handle = <&phy7>; + phy-mode = "internal"; + }; + + port@8 { + reg = <8>; + label = "cpu"; + ethernet = <&gmac0>; + phy-mode = "usxgmii"; + + fixed-link { + speed = <10000>; + full-duplex; + }; + }; + }; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + phy0: ethernet-phy@0 { + reg = <0>; + }; + + phy1: ethernet-phy@1 { + reg = <1>; + }; + + phy2: ethernet-phy@2 { + reg = <2>; + }; + + phy3: ethernet-phy@3 { + reg = <3>; + }; + + phy4: ethernet-phy@4 { + reg = <4>; + }; + + phy5: ethernet-phy@5 { + reg = <5>; + }; + + phy6: ethernet-phy@6 { + reg = <6>; + }; + + phy7: ethernet-phy@7 { + reg = <7>; + }; + }; + }; + };
MAINTAINERS +6 -0
@@ -15613,6 +15613,12 @@ S: Supported F: drivers/net/phy/mxl-86110.c F: drivers/net/phy/mxl-gpy.c +MAXLINEAR MXL862XX SWITCH DRIVER +M: Daniel Golle <[email protected]> +L: [email protected] +S: Maintained +F: Documentation/devicetree/bindings/net/dsa/maxlinear,mxl862xx.yaml + MCAN DEVICE DRIVER M: Markus Schneider-Pargmann <[email protected]> L: [email protected]
Signature · 1 line
2.52.0
Daniel Golle
maintainerRFC PATCH v4 2/4 net: dsa: add tag format for MxL862xx switches
In reply to Daniel GolleAdd proprietary special tag format for the MaxLinear MXL862xx family of switches. While using the same Ethertype as MaxLinear's GSW1xx switches, the actual tag format differs significantly, hence we need a dedicated tag driver for that.
---
RFC v4:
* describe fields and variables with comments
* sub-interface is only 5 bits
* harmonize Kconfig symbol name
* maintain alphabetic order in Kconfig
* fix typo s/beginnig/beginning/
* fix typo s/swtiches/switches/
* arrange local variables in reverse xmas tree order
RFC v3: no changes
RFC v2: make sure all tag fields are initialized
--- MAINTAINERS | 1 + include/net/dsa.h | 2 + net/dsa/Kconfig | 7 +++ net/dsa/Makefile | 1 + net/dsa/tag_mxl862xx.c | 128 +++++++++++++++++++++++++++++++++++++++++ 5 files changed, 139 insertions(+) create mode 100644 net/dsa/tag_mxl862xx.c
MAINTAINERS +1 -0
@@ -15618,6 +15618,7 @@ M: Daniel Golle <[email protected]> L: [email protected] S: Maintained F: Documentation/devicetree/bindings/net/dsa/maxlinear,mxl862xx.yaml +F: net/dsa/tag_mxl862xx.c MCAN DEVICE DRIVER M: Markus Schneider-Pargmann <[email protected]>
include/net/dsa.h +2 -0
@@ -57,6 +57,7 @@ struct tc_action;#define DSA_TAG_PROTO_BRCM_LEGACY_FCS_VALUE 29#define DSA_TAG_PROTO_YT921X_VALUE 30#define DSA_TAG_PROTO_MXL_GSW1XX_VALUE 31 +#define DSA_TAG_PROTO_MXL862_VALUE 32enum dsa_tag_protocol {DSA_TAG_PROTO_NONE =DSA_TAG_PROTO_NONE_VALUE ,
@@ -91,6 +92,7 @@ enum dsa_tag_protocol {DSA_TAG_PROTO_VSC73XX_8021Q =DSA_TAG_PROTO_VSC73XX_8021Q_VALUE ,DSA_TAG_PROTO_YT921X =DSA_TAG_PROTO_YT921X_VALUE ,DSA_TAG_PROTO_MXL_GSW1XX =DSA_TAG_PROTO_MXL_GSW1XX_VALUE , + DSA_TAG_PROTO_MXL862 = DSA_TAG_PROTO_MXL862_VALUE, };struct dsa_switch ;
net/dsa/Kconfig +7 -0
@@ -104,6 +104,13 @@ config NET_DSA_TAG_MTK Say Y or M if you want to enable support for tagging frames for Mediatek switches. +config NET_DSA_TAG_MXL_862XX + tristate "Tag driver for MxL862xx switches" + help + Say Y or M if you want to enable support for tagging frames for the + Maxlinear MxL86252 and MxL86282 switches using their native 8-byte + tagging protocol. + config NET_DSA_TAG_MXL_GSW1XX tristate "Tag driver for MaxLinear GSW1xx switches" help
net/dsa/Makefile +1 -0
@@ -28,6 +28,7 @@ obj-$(CONFIG_NET_DSA_TAG_HELLCREEK) += tag_hellcreek.o obj-$(CONFIG_NET_DSA_TAG_KSZ) += tag_ksz.o obj-$(CONFIG_NET_DSA_TAG_LAN9303) += tag_lan9303.o obj-$(CONFIG_NET_DSA_TAG_MTK) += tag_mtk.o +obj-$(CONFIG_NET_DSA_TAG_MXL_862XX) += tag_mxl862xx.o obj-$(CONFIG_NET_DSA_TAG_MXL_GSW1XX) += tag_mxl-gsw1xx.o obj-$(CONFIG_NET_DSA_TAG_NONE) += tag_none.o obj-$(CONFIG_NET_DSA_TAG_OCELOT) += tag_ocelot.o
net/dsa/tag_mxl862xx.c new file +128 -0
128 lines not on this page · raw message
Signature · 1 line
2.52.0
Daniel Golle
maintainerRFC PATCH v4 3/4 net: mdio: add unlocked mdiodev C45 bus accessors
In reply to Daniel GolleAdd helper inline functions __mdiodev_c45_read() and __mdiodev_c45_write(), which are the C45 equivalents of the existing __mdiodev_read() and __mdiodev_write() added by commit e6a45700e7e1 ("net: mdio: add unlocked mdiobus and mdiodev bus accessors")
---
RFC v4: no changes
RFC v3: no changes
RFC v2: add this patch, initial submission
--- include/linux/mdio.h | 13 +++++++++++++ 1 file changed, 13 insertions(+)
include/linux/mdio.h +13 -0
@@ -648,6 +648,19 @@ static inline int mdiodev_modify_changed(struct mdio_device *mdiodev, mask, set); } +static inline int __mdiodev_c45_read (struct mdio_device *mdiodev,int devad, +u16 regnum) +{ +return __mdiobus_c45_read (mdiodev->bus, mdiodev->addr, devad, regnum); +} + +static inline int __mdiodev_c45_write (struct mdio_device *mdiodev,u32 devad, +u16 regnum,u16 val) +{ +return __mdiobus_c45_write (mdiodev->bus, mdiodev->addr, devad, regnum, + val); +} +static inline int mdiodev_c45_modify (struct mdio_device *mdiodev,int devad,u32 regnum,u16 mask,u16 set) {
Signature · 1 line
2.52.0
Russell King (Oracle)
reviewerRe: [PATCH RFC net-next v4 3/4] net: mdio: add unlocked mdiodev C45 bus accessors
include/linux/mdio.h static inline int mdiodev_modify_changed(struct mdio_device *mdiodev, · line 661
Quoted 5 lines · Daniel Golle
include/linux/mdio.h +5
-0+static inline int __mdiodev_c45_write (struct mdio_device *mdiodev,u32 devad, +u16 regnum,u16 val) +{ +return __mdiobus_c45_write (mdiodev->bus, mdiodev->addr, devad, regnum, + val);
Something doesn't look right here - missing a couple of spaces to correctly align? I suspect checkpatch would spot it?
Signature · 2 lines
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/ FTTP is here! 80Mbps down 10Mbps up. Decent connectivity at last!
Daniel Golle
maintainerRe: [PATCH RFC net-next v4 3/4] net: mdio: add unlocked mdiodev C45 bus accessors
Quoted 9 lines · Russell King (Oracle)
include/linux/mdio.h static inline int mdiodev_modify_changed(struct mdio_device *mdiodev, · line 661
Quoted 5 lines · Daniel Golle
include/linux/mdio.h +5
-0+static inline int __mdiodev_c45_write (struct mdio_device *mdiodev,u32 devad, +u16 regnum,u16 val) +{ +return __mdiobus_c45_write (mdiodev->bus, mdiodev->addr, devad, regnum, + val);Something doesn't look right here - missing a couple of spaces to correctly align? I suspect checkpatch would spot it?
Somehow those two spaces got dropped somewhere on the way. Strangely neither checkpatch.pl locally nor on patchwork[1] caught that -- maybe because 'return' statements are somehow treated differently?
Anyway, fixed in my local tree now and going to be fixed in v5.
Are you otherwise fine with adding those unlocked mdiodev c45 helpers?
RE: [PATCH RFC net-next v4 3/4] net: mdio: add unlocked mdiodev C45 bus accessors
Hi Daniel,
I attached the tools usually included in the FW release for both version 1.0.59.59 v003F and 1.0.76.76 v0061. Here is briefing of the tools:
fullimage_update - update the configuration in the fullimage
start_cfg - compile the start config (pre-configuration)
In start_cfg, you can check the file cfg_in_seq_attached.c.
All the host API described in the CHM files (I sent last time) can be used in this file.
They are invoked in sequence during system boot up.
Run "mk.sh" to compile it into a binary file - start_cfg.bin.
Then use command " ./fullimage_update --start-cfg start_cfg.bin 16384 f48x_full_image.bin" to generate a new fullimage file.
You can play with it and let me know if you have questions.
Thanks & Regards,
Xu Liang
-----Original Message-----
From: Daniel Golle <[email protected]>
Sent: Wednesday, January 7, 2026 6:36 AM
To: Russell King (Oracle) <[email protected]>
Cc: Andrew Lunn <[email protected]>; Vladimir Oltean <[email protected]>; David S. Miller <[email protected]>; Eric Dumazet <[email protected]>; Jakub Kicinski <[email protected]>; Paolo Abeni <[email protected]>; Rob Herring <[email protected]>; Krzysztof Kozlowski <[email protected]>; Conor Dooley <[email protected]>; Heiner Kallweit <[email protected]>; Simon Horman <[email protected]>; [email protected]; [email protected]; [email protected]; Frank Wunderlich <[email protected]>; Chad Monroe <[email protected]>; Cezary Wilmanski <[email protected]>; Avinash Jayaraman <[email protected]>; Bing tao Xu <[email protected]>; Liang Xu <[email protected]>; Juraj Povazanec <[email protected]>; Fanni (Fang-Yi) Chan <[email protected]>; Benny (Ying-Tsan) Weng <[email protected]>; Livia M. Rosu <[email protected]>; John Crispin <[email protected]>
Subject: Re: [PATCH RFC net-next v4 3/4] net: mdio: add unlocked mdiodev C45 bus accessors
This email was sent from outside of MaxLinear.
Quoted 8 lines · Russell King (Oracle)
include/linux/mdio.h static inline int mdiodev_modify_changed(struct mdio_device *mdiodev, · line 661
Quoted 4 lines · Daniel Golle
include/linux/mdio.h +4
-0+static inline int __mdiodev_c45_write (struct mdio_device *mdiodev,u32 devad, +u16 regnum,u16 val) { +return __mdiobus_c45_write (mdiodev->bus, mdiodev->addr, devad, regnum, + val);Something doesn't look right here - missing a couple of spaces to correctly align? I suspect checkpatch would spot it?
Somehow those two spaces got dropped somewhere on the way. Strangely neither checkpatch.pl locally nor on patchwork[1] caught that -- maybe because 'return' statements are somehow treated differently?
Anyway, fixed in my local tree now and going to be fixed in v5.
Are you otherwise fine with adding those unlocked mdiodev c45 helpers?
Russell King (Oracle)
reviewerRe: [PATCH RFC net-next v4 3/4] net: mdio: add unlocked mdiodev C45 bus accessors
In reply to Daniel GolleQuoted 11 lines · Daniel Golle
Quoted 9 lines · Russell King (Oracle)
include/linux/mdio.h static inline int mdiodev_modify_changed(struct mdio_device *mdiodev, · line 661
Quoted 5 lines · Daniel Golle
include/linux/mdio.h +5
-0+static inline int __mdiodev_c45_write (struct mdio_device *mdiodev,u32 devad, +u16 regnum,u16 val) +{ +return __mdiobus_c45_write (mdiodev->bus, mdiodev->addr, devad, regnum, + val);Something doesn't look right here - missing a couple of spaces to correctly align? I suspect checkpatch would spot it?
Quoted 7 lines
Somehow those two spaces got dropped somewhere on the way. Strangely neither checkpatch.pl locally nor on patchwork[1] caught that -- maybe because 'return' statements are somehow treated differently?
Anyway, fixed in my local tree now and going to be fixed in v5.
Are you otherwise fine with adding those unlocked mdiodev c45 helpers?
Yes.
Signature · 2 lines
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/ FTTP is here! 80Mbps down 10Mbps up. Decent connectivity at last!
Daniel Golle
maintainerRFC PATCH v4 4/4 net: dsa: add basic initial driver for MxL862xx switches
In reply to Daniel GolleAdd very basic DSA driver for MaxLinear's MxL862xx switches.
In contrast to previous MaxLinear switches the MxL862xx has a built-in processor that runs a sophisticated firmware based on Zephyr RTOS. Interaction between the host and the switch hence is organized using a software API of that firmware rather than accessing hardware registers directly.
Add descriptions of the most basic firmware API calls to access the built-in MDIO bus hosting the 2.5GE PHYs, basic port control as well as setting up the CPU port.
Implement a very basic DSA driver using that API which is sufficient to get packets flowing between the user ports and the CPU port.
The firmware offers all features one would expect from a modern switch hardware, they will be added one by one in follow-up patch series.
---
RFC v4:
* poll switch readiness after reset
* implement driver shutdown
* added port_fast_aging API call and driver op
* unified port setup in new .port_setup op
* improve comment explaining special handlign for unaligned API read
* various typos
RFC v3:
* fix return value being uninitialized on error in mxl862xx_api_wrap()
* add missing descrition in kerneldoc comment of
struct mxl862xx_ss_sp_tag
RFC v2:
* make use of struct mdio_device
* add phylink_mac_ops stubs
* drop leftover nonsense from mxl862xx_phylink_get_caps()
* use __le32 instead of enum types in over-the-wire structs
* use existing MDIO_* macros whenever possible
* simplify API constants to be more readable
* use readx_poll_timeout instead of open-coding poll timeout loop
* add mxl862xx_reg_read() and mxl862xx_reg_write() helpers
* demystify error codes returned by the firmware
* add #defines for mxl862xx_ss_sp_tag member values
* move reset to dedicated function, clarify magic number being the reset command ID
--- MAINTAINERS | 1 + drivers/net/dsa/Kconfig | 2 + drivers/net/dsa/Makefile | 1 + drivers/net/dsa/mxl862xx/Kconfig | 12 + drivers/net/dsa/mxl862xx/Makefile | 3 + drivers/net/dsa/mxl862xx/mxl862xx-api.h | 177 ++++++++++ drivers/net/dsa/mxl862xx/mxl862xx-cmd.h | 32 ++ drivers/net/dsa/mxl862xx/mxl862xx-host.c | 230 ++++++++++++ drivers/net/dsa/mxl862xx/mxl862xx-host.h | 5 + drivers/net/dsa/mxl862xx/mxl862xx.c | 428 +++++++++++++++++++++++ drivers/net/dsa/mxl862xx/mxl862xx.h | 24 ++ 11 files changed, 915 insertions(+) create mode 100644 drivers/net/dsa/mxl862xx/Kconfig create mode 100644 drivers/net/dsa/mxl862xx/Makefile create mode 100644 drivers/net/dsa/mxl862xx/mxl862xx-api.h create mode 100644 drivers/net/dsa/mxl862xx/mxl862xx-cmd.h create mode 100644 drivers/net/dsa/mxl862xx/mxl862xx-host.c create mode 100644 drivers/net/dsa/mxl862xx/mxl862xx-host.h create mode 100644 drivers/net/dsa/mxl862xx/mxl862xx.c create mode 100644 drivers/net/dsa/mxl862xx/mxl862xx.h
MAINTAINERS +1 -0
@@ -15618,6 +15618,7 @@ M: Daniel Golle <[email protected]> L: [email protected] S: Maintained F: Documentation/devicetree/bindings/net/dsa/maxlinear,mxl862xx.yaml +F: drivers/net/dsa/mxl862xx/ F: net/dsa/tag_mxl862xx.c MCAN DEVICE DRIVER
drivers/net/dsa/Kconfig +2 -0
@@ -74,6 +74,8 @@ source "drivers/net/dsa/microchip/Kconfig" source "drivers/net/dsa/mv88e6xxx/Kconfig" +source "drivers/net/dsa/mxl862xx/Kconfig" + source "drivers/net/dsa/ocelot/Kconfig" source "drivers/net/dsa/qca/Kconfig"
drivers/net/dsa/Makefile +1 -0
@@ -20,6 +20,7 @@ obj-y += hirschmann/ obj-y += lantiq/ obj-y += microchip/ obj-y += mv88e6xxx/ +obj-y += mxl862xx/ obj-y += ocelot/ obj-y += qca/ obj-y += realtek/
drivers/net/dsa/mxl862xx/Kconfig new file +12 -0
@@ -0,0 +1,12 @@ +# SPDX-License-Identifier: GPL-2.0-only +config NET_DSA_MXL862 + tristate "MaxLinear MxL862xx" + depends on NET_DSA + select MAXLINEAR_GPHY + select NET_DSA_TAG_MXL_862XX + help + This enables support for the MaxLinear MxL862xx switch family. + These switches have two 10GE SerDes interfaces, one typically + used as CPU port. + MxL86282 has eight 2.5 Gigabit PHYs + MxL86252 has five 2.5 Gigabit PHYs
drivers/net/dsa/mxl862xx/Makefile new file +3 -0
@@ -0,0 +1,3 @@ +# SPDX-License-Identifier: GPL-2.0 +obj-$(CONFIG_NET_DSA_MXL862) += mxl862xx_dsa.o +mxl862xx_dsa-y := mxl862xx.o mxl862xx-host.o
drivers/net/dsa/mxl862xx/mxl862xx-api.h new file +177 -0
177 lines not on this page · raw message
drivers/net/dsa/mxl862xx/mxl862xx-cmd.h new file +32 -0
@@ -0,0 +1,32 @@ +/* SPDX-License-Identifier: GPL-2.0-or-later */ + +#define MXL862XX_MMD_DEV 30 +#define MXL862XX_MMD_REG_CTRL 0 +#define MXL862XX_MMD_REG_LEN_RET 1 +#define MXL862XX_MMD_REG_DATA_FIRST 2 +#define MXL862XX_MMD_REG_DATA_LAST 95 +#define MXL862XX_MMD_REG_DATA_MAX_SIZE \ + (MXL862XX_MMD_REG_DATA_LAST - MXL862XX_MMD_REG_DATA_FIRST + 1) + +#define MXL862XX_COMMON_MAGIC 0x100 +#define MXL862XX_CTP_MAGIC 0x500 +#define MXL862XX_SWMAC_MAGIC 0xa00 +#define MXL862XX_SS_MAGIC 0x1600 +#define GPY_GPY2XX_MAGIC 0x1800 +#define SYS_MISC_MAGIC 0x1900 + +#define MXL862XX_COMMON_CFGGET (MXL862XX_COMMON_MAGIC + 0x9) +#define MXL862XX_COMMON_REGISTERMOD (MXL862XX_COMMON_MAGIC + 0x11) + +#define MXL862XX_CTP_PORTASSIGNMENTSET (MXL862XX_CTP_MAGIC + 0x3) + +#define MXL862XX_MAC_TABLECLEARCOND (MXL862XX_SWMAC_MAGIC + 0x8) + +#define MXL862XX_SS_SPTAG_SET (MXL862XX_SS_MAGIC + 0x02) + +#define INT_GPHY_READ (GPY_GPY2XX_MAGIC + 0x01) +#define INT_GPHY_WRITE (GPY_GPY2XX_MAGIC + 0x02) + +#define SYS_MISC_FW_VERSION (SYS_MISC_MAGIC + 0x02) + +#define MMD_API_MAXIMUM_ID 0x7fff
drivers/net/dsa/mxl862xx/mxl862xx-host.c new file +230 -0
230 lines not on this page · raw message
drivers/net/dsa/mxl862xx/mxl862xx-host.h new file +5 -0
@@ -0,0 +1,5 @@ +/* SPDX-License-Identifier: GPL-2.0-or-later */ + +int mxl862xx_api_wrap (struct mxl862xx_priv *priv,u16 cmd,void *data,u16 size, +bool read,bool quiet); +int mxl862xx_reset (struct mxl862xx_priv *priv);
drivers/net/dsa/mxl862xx/mxl862xx.c new file +428 -0
428 lines not on this page · raw message
drivers/net/dsa/mxl862xx/mxl862xx.h new file +24 -0
@@ -0,0 +1,24 @@ +/* SPDX-License-Identifier: GPL-2.0-or-later */ + +#define MXL862XX_MAX_PHY_PORT_NUM 8 +#define MXL862XX_MAX_EXT_PORT_NUM 7 +#define MXL862XX_MAX_PORT_NUM (MXL862XX_MAX_PHY_PORT_NUM + \ + MXL862XX_MAX_EXT_PORT_NUM) + +#define MXL86252_PHY_PORT_NUM 5 +#define MXL86282_PHY_PORT_NUM 8 + +#define MXL86252_EXT_PORT_NUM 2 +#define MXL86282_EXT_PORT_NUM 2 + +struct mxl862xx_hw_info { +u8 max_ports; +u8 phy_ports; +u8 ext_ports; +}; + +struct mxl862xx_priv { +struct dsa_switch *ds; +struct mdio_device *mdiodev; +const struct mxl862xx_hw_info *hw_info; +};
Signature · 1 line
2.52.0