arm: dts: sc5xx: device tree updates and fixes
cover arm: dts: sc5xx: device tree updates and fixes
From: Ozan Durgut <[email protected]>
This series introduces updates for Analog Devices SC5xx boards.
It cleans up device trees by renaming GPIO expanders and removing incorrect SPI flash definitions from the common include file.
For the SC598, this series updates the EZLITE board to the latest Revision E hardware. It also adds missing GPIO hogs and enables additional commands for the EZKIT configuration.
Ozan Durgut (4):
configs: sc598-ezkit: enable additional commands
arm: dts: sc598: add missing GPIO hogs for Rev D
arm: dts: adi: rename GPIO expanders
arm: dts: sc598: update EZLITE to latest revision
Philip Molloy (1):
arm: dts: sc5xx: drop SPI flash from common dtsi
arch/arm/dts/sc573-ezkit.dts | 4 ++-- arch/arm/dts/sc584-ezkit.dts | 4 ++-- arch/arm/dts/sc589-ezkit.dts | 4 ++-- arch/arm/dts/sc594-som-ezkit.dts | 2 +- arch/arm/dts/sc594-som-ezlite.dts | 2 +- arch/arm/dts/sc598-som-ezkit.dts | 2 +- arch/arm/dts/sc598-som-ezlite.dts | 4 ++-- arch/arm/dts/sc598-som-revD.dtsi | 32 +++++++++++++++++++++++++++ arch/arm/dts/sc5xx.dtsi | 11 --------- configs/sc598-som-ezkit-spl_defconfig | 4 ++++ 10 files changed, 47 insertions(+), 22 deletions(-)
Signature · 1 line
2.43.0
PATCH 1/5 configs: sc598-ezkit: enable additional commands
From: Ozan Durgut <[email protected]>
Enable FAT and GPT support, as well as mtd and wget commands
--- configs/sc598-som-ezkit-spl_defconfig | 4 ++++ 1 file changed, 4 insertions(+)
configs/sc598-som-ezkit-spl_defconfig +4 -0
@@ -109,3 +109,7 @@ CONFIG_USB_DWC2=y CONFIG_USB_STORAGE=y # CONFIG_SPL_CRC8 is not set # CONFIG_TOOLS_MKEFICAPSULE is not set +CONFIG_CMD_FAT=y +CONFIG_CMD_GPT=y +CONFIG_CMD_MTD=y +CONFIG_CMD_WGET=y
Signature · 1 line
2.43.0
PATCH 2/5 arm: dts: sc598: add missing GPIO hogs for Rev D
In reply to [email protected]From: Ozan Durgut <[email protected]>
Add missing GPIO hogs for UART0 enable, UART0 flow control, SD Card and eMMC control signals.
--- arch/arm/dts/sc598-som-revD.dtsi | 32 ++++++++++++++++++++++++++++++++ 1 file changed, 32 insertions(+)
arch/arm/dts/sc598-som-revD.dtsi +32 -0
@@ -55,6 +55,38 @@ line-name = "spi2flash-cs"; bootph-pre-ram; }; + + uart0 { + gpio-hog; + gpios = <5 GPIO_ACTIVE_LOW>; + output-high; + line-name = "uart0-en"; + bootph-pre-ram; + }; + + uart0-flow-en { + gpio-hog; + gpios = <6 GPIO_ACTIVE_LOW>; + output-low; + line-name = "uart0-flow-en"; + bootph-pre-ram; + }; + + som-emmc { + gpio-hog; + gpios = <8 GPIO_ACTIVE_LOW>; + output-high; + line-name = "som-emmc-en"; + bootph-pre-ram; + }; + + crr-sdcard { + gpio-hog; + gpios = <9 GPIO_ACTIVE_LOW>; + output-low; + line-name = "crr-sdcard-en"; + bootph-pre-ram; + }; }; };
Signature · 1 line
2.43.0
PATCH 3/5 arm: dts: sc5xx: drop SPI flash from common dtsi
In reply to [email protected]From: Philip Molloy <[email protected]>
SPI flash devices are not common across all SC5xx boards. They already defined in the SoM-specific dtsi files. Keeping the definition in the common dtsi is therefore incorrect.
--- arch/arm/dts/sc5xx.dtsi | 11 ----------- 1 file changed, 11 deletions(-)
arch/arm/dts/sc5xx.dtsi +0 -11
@@ -154,17 +154,6 @@ clock-names = "spi"; status = "okay"; bootph-pre-ram; - - flash1: is25lp512@1 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "jedec,spi-nor", "is25lp512"; - reg = <1>; - spi-tx-bus-width = <4>; - spi-rx-bus-width = <4>; - spi-max-frequency = <10000000>; - bootph-pre-ram; - }; }; wdog: watchdog@31008000 {
Signature · 1 line
2.43.0
PATCH 4/5 arm: dts: adi: rename GPIO expanders
In reply to [email protected]From: Ozan Durgut <[email protected]>
The current naming convention for GPIO expanders across ADI SC5xx device trees is inconsistent. This patch updates the node names to correct indexing and clarify hardware location.
For SC573, SC584, and SC589 evaluation SBCs, switch to zero-based indexing to align with standard conventions.
For SC594 and SC598 SoM + carrier evaluation kits, rename the nodes to crr_gpio_expander. This prefix indicates which board the expander is on.
--- arch/arm/dts/sc573-ezkit.dts | 4 ++-- arch/arm/dts/sc584-ezkit.dts | 4 ++-- arch/arm/dts/sc589-ezkit.dts | 4 ++-- arch/arm/dts/sc594-som-ezkit.dts | 2 +- arch/arm/dts/sc594-som-ezlite.dts | 2 +- arch/arm/dts/sc598-som-ezkit.dts | 2 +- arch/arm/dts/sc598-som-ezlite.dts | 2 +- 7 files changed, 10 insertions(+), 10 deletions(-)
arch/arm/dts/sc573-ezkit.dts +2 -2
@@ -14,7 +14,7 @@ }; &i2c0 { - gpio_expander1: mcp23017@21 { + gpio_expander0: mcp23017@21 { compatible = "microchip,mcp23017"; reg = <0x21>; gpio-controller;
@@ -118,7 +118,7 @@ }; }; - gpio_expander2: mcp23017@22 { + gpio_expander1: mcp23017@22 { compatible = "microchip,mcp23017"; reg = <0x22>; gpio-controller;
arch/arm/dts/sc584-ezkit.dts +2 -2
@@ -13,7 +13,7 @@ }; &i2c2 { - gpio_expander1: mcp23017@21 { + gpio_expander0: mcp23017@21 { compatible = "microchip,mcp23017"; reg = <0x21>; gpio-controller;
@@ -125,7 +125,7 @@ }; }; - gpio_expander2: mcp23017@22 { + gpio_expander1: mcp23017@22 { compatible = "microchip,mcp23017"; reg = <0x22>; gpio-controller;
arch/arm/dts/sc589-ezkit.dts +2 -2
@@ -17,7 +17,7 @@ &i2c0 { #address-cells = <1>; #size-cells = <0>; - gpio_expander1: mcp23017@21 { + gpio_expander0: mcp23017@21 { compatible = "microchip,mcp23017"; reg = <0x21>; gpio-controller;
@@ -145,7 +145,7 @@ }; }; - gpio_expander2: mcp23017@22 { + gpio_expander1: mcp23017@22 { compatible = "microchip,mcp23017"; reg = <0x22>; gpio-controller;
arch/arm/dts/sc594-som-ezkit.dts +1 -1
@@ -13,7 +13,7 @@ }; &i2c2 { - gpio_expander2: mcp23017@22 { + crr_gpio_expander: mcp23017@22 { compatible = "microchip,mcp23017"; reg = <0x22>; gpio-controller;
arch/arm/dts/sc594-som-ezlite.dts +1 -1
@@ -13,7 +13,7 @@ }; &i2c2 { - gpio_expander: adp5588@30 { + crr_gpio_expander: adp5588@30 { compatible = "adi,adp5588"; reg = <0x30>; gpio-controller;
arch/arm/dts/sc598-som-ezkit.dts +1 -1
@@ -13,7 +13,7 @@ }; &i2c2 { - gpio_expander2: mcp23017@22 { + crr_gpio_expander: mcp23017@22 { compatible = "microchip,mcp23017"; reg = <0x22>; gpio-controller;
arch/arm/dts/sc598-som-ezlite.dts +1 -1
@@ -13,7 +13,7 @@ }; &i2c2 { - gpio_expander: adp5588@30 { + crr_gpio_expander: adp5588@30 { compatible = "adi,adp5588"; reg = <0x30>; gpio-controller;
Signature · 1 line
2.43.0
PATCH 5/5 arm: dts: sc598: update EZLITE to latest revision
In reply to [email protected]From: Ozan Durgut <[email protected]>
Update the SC598 SOM EZLITE device tree to use the latest revision of the System on Module (Rev E).
--- arch/arm/dts/sc598-som-ezlite.dts | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
arch/arm/dts/sc598-som-ezlite.dts +1 -1
@@ -5,7 +5,7 @@ /dts-v1/; -#include "sc598-som-revD.dtsi" +#include "sc598-som-revE.dtsi" / { model = "ADI SC598-SOM-EZLITE";
Signature · 1 line
2.43.0
Hi Ozan and Tom,
Quoted 33 lines · On Mon, Jan 26, 2026 at 11:15 AM <[email protected]> wrote:
From: Ozan Durgut <[email protected]>
This series introduces updates for Analog Devices SC5xx boards.
It cleans up device trees by renaming GPIO expanders and removing incorrect SPI flash definitions from the common include file.
For the SC598, this series updates the EZLITE board to the latest Revision E hardware. It also adds missing GPIO hogs and enables additional commands for the EZKIT configuration.
Ozan Durgut (4):
configs: sc598-ezkit: enable additional commands
arm: dts: sc598: add missing GPIO hogs for Rev D
arm: dts: adi: rename GPIO expanders
arm: dts: sc598: update EZLITE to latest revisionPhilip Molloy (1):
arm: dts: sc5xx: drop SPI flash from common dtsiarch/arm/dts/sc573-ezkit.dts | 4 ++-- arch/arm/dts/sc584-ezkit.dts | 4 ++-- arch/arm/dts/sc589-ezkit.dts | 4 ++-- arch/arm/dts/sc594-som-ezkit.dts | 2 +- arch/arm/dts/sc594-som-ezlite.dts | 2 +- arch/arm/dts/sc598-som-ezkit.dts | 2 +- arch/arm/dts/sc598-som-ezlite.dts | 4 ++-- arch/arm/dts/sc598-som-revD.dtsi | 32 +++++++++++++++++++++++++++ arch/arm/dts/sc5xx.dtsi | 11 --------- configs/sc598-som-ezkit-spl_defconfig | 4 ++++ 10 files changed, 47 insertions(+), 22 deletions(-)
Quoted 3 lines
--
2.43.0
I tried this series on top of 2026.04-rc1 and ran my usual tests against an sc573 ezkit and an sc598 rev D som + ezkit carrier board. Note that to test the rev D board I have to omit dtsi switch to rev E, but other than that everything looks good to me functionality-wise. Some commit messages could be expanded (such as adding info about why wget/fat/gpt/mtd are being enabled), but I don't see a need to resubmit just for that.
For the series,
Thanks,
Greg
Quoted 8 lines · On Mon, 26 Jan 2026 17:15:00 +0100, [email protected] wrote:
From: Ozan Durgut <[email protected]>
This series introduces updates for Analog Devices SC5xx boards.
It cleans up device trees by renaming GPIO expanders and removing incorrect SPI flash definitions from the common include file.
[...]
Applied to u-boot/master, thanks!
[1/5] configs: sc598-ezkit: enable additional commands
commit: d9f1fcb304839a1e1c3cec91b9ec91d01e02c9c7
[2/5] arm: dts: sc598: add missing GPIO hogs for Rev D
commit: fb4a6389314333a302b85b245eb71feb0bcbb9af
[3/5] arm: dts: sc5xx: drop SPI flash from common dtsi
commit: 89a197e7e34d7148ed3f9eda5d684d7e5e673c69
[4/5] arm: dts: adi: rename GPIO expanders
commit: 9a49dcf6ab71b5fffa106554ca22a73122cdd275
[5/5] arm: dts: sc598: update EZLITE to latest revision
commit: d047a99d08d83535020173268439b7793c2f3f27Signature · 1 line
Tom