ASoC: mediatek: mt2701: HDMI audio support

This series wires up on-chip HDMI audio on MT2701 and MT7623N, from the DRM bridge down through the AFE into a small machine driver that binds the AFE HDMI BE to the HDMI TX codec already exposed by the mediatek-drm-hdmi driver. Bindings, DT and a BananaPi R2 board node are included.

In order to survive vblank or late hotplug of the monitor, the fix submitted separately [1] is required as well.

Everything here was developed for and tested on a BananaPi R2 (MT7623N), which turns ten years old this year -- a nice occasion to finally land HDMI audio for a SoC which was truly ahead of its time.

[1]: https://patchwork.kernel.org/project/linux-mediatek/patch/a3e22cbae528c9a38d854a586d1736b860998d41.1776265222.git.daniel@makrotopia.org/

Changes since v2:
* allOf goes before additionalProperties
* remove now unused clk bits
* remove redundant clock un-gating via regmap access

Changes since v1:
* Restrict the four HDMI clocks to mediatek,mt2701-audio only using an allOf/if/then conditional; MT7622 is capped at 34 clocks (Krzysztof Kozlowski)
* Fix subject prefix to use schema filename (Krzysztof Kozlowski)
* Rewrite title and description to describe hardware, not driver (Krzysztof Kozlowski)
* Clarify in commit message why this is a separate binding from mediatek,mt2701-audio (Krzysztof Kozlowski)
* use named masks and explicitly set BIT_WIDTH_16 when programming AFE_HDMI_OUT_CON0 channel count (Mark Brown)
* add AUDIO_TOP_CON3, AFE_HDMI_OUT_CON0, AFE_HDMI_CONN0, AFE_8CH_I2S_OUT_CON to suspend/resume backup list (Mark Brown)

Daniel Golle (9):
ASoC: dt-bindings: mt2701-afe-pcm: add HDMI audio path clocks
ASoC: dt-bindings: mediatek,mt2701-hdmi-audio: add MT2701 HDMI audio
ASoC: mediatek: mt2701: add AFE HDMI register definitions
ASoC: mediatek: mt2701: add optional HDMI audio path clocks
ASoC: mediatek: mt2701: add HDMI audio memif, FE and BE DAIs
ASoC: mediatek: mt2701: add machine driver for on-chip HDMI codec
ARM: dts: mediatek: mt2701: wire HDMI audio path clocks into AFE
ARM: dts: mediatek: mt7623: wire HDMI audio path clocks into AFE
ARM: dts: mediatek: mt7623n-bananapi-bpi-r2: add HDMI audio machine
node

 .../bindings/sound/mediatek,mt2701-audio.yaml |  23 ++
 .../sound/mediatek,mt2701-hdmi-audio.yaml     |  48 +++
 arch/arm/boot/dts/mediatek/mt2701.dtsi        |  21 +-
 arch/arm/boot/dts/mediatek/mt7623.dtsi        |  21 +-
 .../dts/mediatek/mt7623n-bananapi-bpi-r2.dts  |   7 +
 sound/soc/mediatek/Kconfig                    |  10 +
 sound/soc/mediatek/mt2701/Makefile            |   1 +
 .../mediatek/mt2701/mt2701-afe-clock-ctrl.c   |  22 ++
 sound/soc/mediatek/mt2701/mt2701-afe-common.h |   6 +
 sound/soc/mediatek/mt2701/mt2701-afe-pcm.c    | 284 +++++++++++++++++-
 sound/soc/mediatek/mt2701/mt2701-hdmi.c       | 114 +++++++
 sound/soc/mediatek/mt2701/mt2701-reg.h        |  29 ++
 12 files changed, 575 insertions(+), 11 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/sound/mediatek,mt2701-hdmi-audio.yaml
 create mode 100644 sound/soc/mediatek/mt2701/mt2701-hdmi.c

2.54.0

Document four additional optional clocks feeding the HDMI audio output path on MT2701: the HADDS2 PLL (root of the HDMI audio clock tree), the HDMI audio and S/PDIF interface power gates, and the audio APLL root gate. Older device trees that do not wire these up remain valid via minItems. MT7622 does not have HDMI audio hardware, so its compatible is restricted to the base set of 34 clocks.

---
v3: allOf goes before additionalProperties
v2:
* Restrict the four HDMI clocks to mediatek,mt2701-audio only using an allOf/if/then conditional; MT7622 is capped at 34 clocks (Krzysztof Kozlowski)

 .../bindings/sound/mediatek,mt2701-audio.yaml | 23 +++++++++++++++++++
 1 file changed, 23 insertions(+)

index 45382c4d86aa..30f331366566 100644
@@ -32,6 +32,7 @@ properties:
     maxItems: 1
 
   clocks:
+    minItems: 34
     items:
       - description: audio infra sys clock
       - description: top audio mux 1

@@ -67,8 +68,13 @@ properties:
       - description: top audio a1 sys pd
       - description: top audio a2 sys pd
       - description: audio merge interface pd
+      - description: HADDS2 PLL 294 MHz (HDMI audio path root)
+      - description: HDMI audio interface pd
+      - description: S/PDIF interface pd
+      - description: audio APLL root pd
 
   clock-names:
+    minItems: 34
     items:
       - const: infra_sys_audio_clk
       - const: top_audio_mux1_sel

@@ -104,6 +110,10 @@ properties:
       - const: audio_a1sys_pd
       - const: audio_a2sys_pd
       - const: audio_mrgif_pd
+      - const: hadds2pll_294m
+      - const: audio_hdmi_pd
+      - const: audio_spdf_pd
+      - const: audio_apll_pd
 
 required:
   - compatible

@@ -113,4 +123,17 @@ required:
   - clocks
   - clock-names
 
+allOf:
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: mediatek,mt7622-audio
+    then:
+      properties:
+        clocks:
+          maxItems: 34
+        clock-names:
+          maxItems: 34
+
 additionalProperties: false

2.54.0

Describe the sound card node that routes the MT2701/MT7623N AFE HDMI playback path to the on-chip HDMI transmitter. This is separate from the AFE platform binding (mediatek,mt2701-audio) because it represents board-level audio routing between the AFE and the HDMI codec, not an additional IP block. MT7623N boards carry the same IP and use the mt7623n- compatible as a fallback to mt2701-.

---
v3: no changes
v2:
* Fix subject prefix to use schema filename (Krzysztof Kozlowski)
* Rewrite title and description to describe hardware, not driver (Krzysztof Kozlowski)
* Clarify in commit message why this is a separate binding from mediatek,mt2701-audio (Krzysztof Kozlowski)

 .../sound/mediatek,mt2701-hdmi-audio.yaml     | 48 +++++++++++++++++++
 1 file changed, 48 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/sound/mediatek,mt2701-hdmi-audio.yaml

new file mode 100644
index 000000000000..9d5a8166e51f
@@ -0,0 +1,48 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/sound/mediatek,mt2701-hdmi-audio.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: MediaTek MT2701/MT7623N HDMI audio output
+
+maintainers:
+  - Daniel Golle <[email protected]>
+
+description:
+  Sound card routing the MT2701/MT7623N Audio Front End HDMI
+  playback path to the on-chip HDMI transmitter. The AFE
+  provides the DMA memif and internal I2S engine; the HDMI
+  transmitter acts as the audio codec on the serialised link.
+
+properties:
+  compatible:
+    oneOf:
+      - const: mediatek,mt2701-hdmi-audio
+      - items:
+          - const: mediatek,mt7623n-hdmi-audio
+          - const: mediatek,mt2701-hdmi-audio
+
+  mediatek,platform:
+    $ref: /schemas/types.yaml#/definitions/phandle
+    description: Phandle of the MT2701/MT7623N AFE platform node.
+
+  mediatek,audio-codec:
+    $ref: /schemas/types.yaml#/definitions/phandle
+    description: Phandle of the HDMI transmitter acting as audio codec.
+
+required:
+  - compatible
+  - mediatek,platform
+  - mediatek,audio-codec
+
+additionalProperties: false
+
+examples:
+  - |
+    sound-hdmi {
+        compatible = "mediatek,mt7623n-hdmi-audio",
+                     "mediatek,mt2701-hdmi-audio";
+        mediatek,platform = <&afe>;
+        mediatek,audio-codec = <&hdmi0>;
+    };

2.54.0

Add register offsets and bit defines for the MT2701/MT7623N AFE HDMI audio output path: the HDMI BCK divider in AUDIO_TOP_CON3, the HDMI output memif control and descriptor registers, the 8-bit AFE_HDMI_CONN0 interconnect, and the AFE_8CH_I2S_OUT_CON engine that drives the HDMI TX serial link. These are a prerequisite for adding an HDMI playback path to the mt2701 AFE driver and have no behavioural effect on their own.

---
v3: remove now unused clk bits
v2: no changes

 sound/soc/mediatek/mt2701/mt2701-reg.h | 29 ++++++++++++++++++++++++++
 1 file changed, 29 insertions(+)

index c84d14cdd7ae..ca914df02c96 100644
@@ -10,10 +10,17 @@
 #define _MT2701_REG_H_
 
 #define AUDIO_TOP_CON0 0x0000
+#define AUDIO_TOP_CON3 0x000c
 #define AUDIO_TOP_CON4 0x0010
 #define AUDIO_TOP_CON5 0x0014
 #define AFE_DAIBT_CON0 0x001c
 #define AFE_MRGIF_CON 0x003c
+#define AFE_HDMI_OUT_CON0 0x0370
+#define AFE_HDMI_OUT_BASE 0x0374
+#define AFE_HDMI_OUT_CUR  0x0378
+#define AFE_HDMI_OUT_END  0x037c
+#define AFE_HDMI_CONN0    0x0390
+#define AFE_8CH_I2S_OUT_CON 0x0394
 #define ASMI_TIMING_CON1 0x0100
 #define ASMO_TIMING_CON1 0x0104
 #define PWR1_ASM_CON1 0x0108

@@ -125,6 +132,28 @@
 #define AFE_MEMIF_PBUF_SIZE_DLM_BYTE_MASK	(0x3 << 12)
 #define AFE_MEMIF_PBUF_SIZE_DLM_32BYTES		(0x1 << 12)
 
+/* AUDIO_TOP_CON3 (0x000c) -- HDMI BCK divider */
+#define AUDIO_TOP_CON3_HDMI_BCK_DIV_MASK	(0x3f << 8)
+#define AUDIO_TOP_CON3_HDMI_BCK_DIV(x)		(((x) & 0x3f) << 8)
+
+/* AFE_HDMI_OUT_CON0 (0x0370) */
+#define AFE_HDMI_OUT_CON0_OUT_ON		(0x1 << 0)
+#define AFE_HDMI_OUT_CON0_BIT_WIDTH_MASK	(0x1 << 1)
+#define AFE_HDMI_OUT_CON0_BIT_WIDTH_16		(0x0 << 1)
+#define AFE_HDMI_OUT_CON0_BIT_WIDTH_32		(0x1 << 1)
+#define AFE_HDMI_OUT_CON0_CH_NUM_MASK		(0xf << 4)
+#define AFE_HDMI_OUT_CON0_CH_NUM(x)		(((x) & 0xf) << 4)
+
+/* AFE_8CH_I2S_OUT_CON (0x0394) -- on-SoC 8-channel I2S that feeds HDMI TX */
+#define AFE_8CH_I2S_OUT_CON_EN			(0x1 << 0)
+#define AFE_8CH_I2S_OUT_CON_BCK_INV		(0x1 << 1)
+#define AFE_8CH_I2S_OUT_CON_LRCK_INV		(0x1 << 2)
+#define AFE_8CH_I2S_OUT_CON_I2S_DELAY		(0x1 << 3)
+#define AFE_8CH_I2S_OUT_CON_WLEN_MASK		(0x3 << 4)
+#define AFE_8CH_I2S_OUT_CON_WLEN_16BIT		(0x1 << 4)
+#define AFE_8CH_I2S_OUT_CON_WLEN_24BIT		(0x2 << 4)
+#define AFE_8CH_I2S_OUT_CON_WLEN_32BIT		(0x3 << 4)
+
 /* I2S in/out register bit control */
 #define ASYS_I2S_CON_FS			(0x1f << 8)
 #define ASYS_I2S_CON_FS_SET(x)		((x) << 8)

2.54.0

The HDMI audio output path on MT2701/MT7623N is rooted in HADDS2PLL and gated by the audio_hdmi, audio_spdf and audio_apll power gates. Acquire these four clocks from device tree using devm_clk_get_optional so that existing platforms which do not wire up HDMI audio keep probing unchanged. Actual clock enable/prepare is deferred to the upcoming HDMI DAI startup path.

---
v3: no changes
v2: no changes

 .../mediatek/mt2701/mt2701-afe-clock-ctrl.c   | 22 +++++++++++++++++++
 sound/soc/mediatek/mt2701/mt2701-afe-common.h |  4 ++++
 2 files changed, 26 insertions(+)

index ae620890bb3a..5a2bcf027b4f 100644
@@ -95,6 +95,28 @@ int mt2701_init_clock(struct mtk_base_afe *afe)
 		afe_priv->mrgif_ck = NULL;
 	}
 
+	/*
+	 * Optional HDMI audio clocks. Platforms that do not wire up the
+	 * HDMI output (e.g. MT2701 devkits using only the I2S BE DAIs)
+	 * may omit these; in that case the HDMI BE DAI simply cannot be
+	 * enabled, but the rest of the AFE still probes.
+	 */
+	afe_priv->hadds2pll_ck = devm_clk_get_optional(afe->dev, "hadds2pll_294m");
+	if (IS_ERR(afe_priv->hadds2pll_ck))
+		return PTR_ERR(afe_priv->hadds2pll_ck);
+
+	afe_priv->audio_hdmi_ck = devm_clk_get_optional(afe->dev, "audio_hdmi_pd");
+	if (IS_ERR(afe_priv->audio_hdmi_ck))
+		return PTR_ERR(afe_priv->audio_hdmi_ck);
+
+	afe_priv->audio_spdf_ck = devm_clk_get_optional(afe->dev, "audio_spdf_pd");
+	if (IS_ERR(afe_priv->audio_spdf_ck))
+		return PTR_ERR(afe_priv->audio_spdf_ck);
+
+	afe_priv->audio_apll_ck = devm_clk_get_optional(afe->dev, "audio_apll_pd");
+	if (IS_ERR(afe_priv->audio_apll_ck))
+		return PTR_ERR(afe_priv->audio_apll_ck);
+
 	return 0;
 }
 

index 32bef5e2a56d..7b15283d6351 100644
@@ -90,6 +90,10 @@ struct mt2701_afe_private {
 	struct mt2701_i2s_path *i2s_path;
 	struct clk *base_ck[MT2701_BASE_CLK_NUM];
 	struct clk *mrgif_ck;
+	struct clk *hadds2pll_ck;
+	struct clk *audio_hdmi_ck;
+	struct clk *audio_spdf_ck;
+	struct clk *audio_apll_ck;
 	bool mrg_enable[MTK_STREAM_NUM];
 
 	const struct mt2701_soc_variants *soc;

2.54.0

Extend the MT2701/MT7623N AFE driver with the HDMI playback path:

- a new HDMI DMA memif (MT2701_MEMIF_HDMI) mapped to the

    AFE_HDMI_OUT_{CON0,BASE,CUR,END} registers;
  - a PCM_HDMI front-end DAI (S16_LE only, 44.1k/48k) which feeds
    the memif via DPCM;

- an HDMI BE DAI wrapping the AFE_8CH_I2S_OUT_CON engine that serialises L/R samples towards the on-chip HDMI transmitter.

Sample-rate programming uses the empirically determined HDMI_BCK_DIV = 45 * 48000 / rate - 1 formula in AUDIO_TOP_CON3, which covers 44.1 kHz and 48 kHz within the 6-bit divider range. The AFE_HDMI_CONN0 interconnect is programmed to route memif output pairs to the serializer inputs with L/R in the right order for hdmi-audio-codec.

The existing I2S engine helpers (mt2701_mclk_configuration, mt2701_i2s_path_enable, mt2701_afe_i2s_path_disable) are reused for the HDMI BE so that MCLK at 128*fs and the ASYS I2S3 FS field are programmed and cleanly released across open/close cycles.

Only S16_LE and 44.1k/48k are exposed to userspace. Other rates fall outside the 6-bit BCK divider range, and wider sample formats require DMA BIT_WIDTH programming that the current memif setup does not handle. These limits match what the MT8173 AFE driver exposes for its HDMI path.

The HDMI-related AFE registers (AUDIO_TOP_CON3, AFE_HDMI_OUT_CON0, AFE_HDMI_CONN0, AFE_8CH_I2S_OUT_CON) are added to the suspend backup list so that the existing mtk_afe_suspend/resume framework saves and restores them across system sleep cycles.

---
v3:
* remove redundant clock un-gating via regmap access
v2:
* use named masks and explicitly set BIT_WIDTH_16 when programming AFE_HDMI_OUT_CON0 channel count (Mark Brown)
* add AUDIO_TOP_CON3, AFE_HDMI_OUT_CON0, AFE_HDMI_CONN0, AFE_8CH_I2S_OUT_CON to suspend/resume backup list (Mark Brown)

 sound/soc/mediatek/mt2701/mt2701-afe-common.h |   2 +
 sound/soc/mediatek/mt2701/mt2701-afe-pcm.c    | 284 +++++++++++++++++-
 2 files changed, 285 insertions(+), 1 deletion(-)

index 7b15283d6351..8b6f3a200048 100644
@@ -33,6 +33,7 @@ enum {
 	MT2701_MEMIF_UL5,
 	MT2701_MEMIF_DLBT,
 	MT2701_MEMIF_ULBT,
+	MT2701_MEMIF_HDMI,
 	MT2701_MEMIF_NUM,
 	MT2701_IO_I2S = MT2701_MEMIF_NUM,
 	MT2701_IO_2ND_I2S,

@@ -41,6 +42,7 @@ enum {
 	MT2701_IO_5TH_I2S,
 	MT2701_IO_6TH_I2S,
 	MT2701_IO_MRG,
+	MT2701_IO_HDMI,
 };
 
 enum {

2.54.0

Add a simple ASoC machine driver that wires the MT2701/MT7623N AFE HDMI playback path to the on-chip HDMI transmitter exposed as a generic hdmi-audio-codec "i2s-hifi" DAI.

The driver binds to "mediatek,mt2701-hdmi-audio". MT7623N device trees carry "mediatek,mt7623n-hdmi-audio" as a board-specific fallback, matching the dt-binding.

---
v3: no changes
v2: no changes

 sound/soc/mediatek/Kconfig              |  10 +++
 sound/soc/mediatek/mt2701/Makefile      |   1 +
 sound/soc/mediatek/mt2701/mt2701-hdmi.c | 114 ++++++++++++++++++++++++
 3 files changed, 125 insertions(+)
 create mode 100644 sound/soc/mediatek/mt2701/mt2701-hdmi.c

index 3a1e1fa3fe5c..fa076e7854ad 100644
@@ -26,6 +26,16 @@ config SND_SOC_MT2701_CS42448
 	  Select Y if you have such device.
 	  If unsure select "N".
 
+config SND_SOC_MT2701_HDMI
+	tristate "ASoC Audio driver for MT2701 with on-chip HDMI codec"
+	depends on SND_SOC_MT2701
+	select SND_SOC_HDMI_CODEC
+	help
+	  This adds the ASoC machine driver for MediaTek MT2701 and
+	  MT7623N boards routing the AFE I2S back-end to the on-chip
+	  HDMI transmitter via the generic HDMI codec.
+	  If unsure select "N".
+
 config SND_SOC_MT2701_WM8960
 	tristate "ASoc Audio driver for MT2701 with WM8960 codec"
 	depends on SND_SOC_MT2701 && I2C

index 507fa26c3945..59623d3d3a03 100644
@@ -5,4 +5,5 @@ obj-$(CONFIG_SND_SOC_MT2701) += snd-soc-mt2701-afe.o
 
 # machine driver
 obj-$(CONFIG_SND_SOC_MT2701_CS42448) += mt2701-cs42448.o
+obj-$(CONFIG_SND_SOC_MT2701_HDMI) += mt2701-hdmi.o
 obj-$(CONFIG_SND_SOC_MT2701_WM8960) += mt2701-wm8960.o

2.54.0

Add the HADDS2 PLL 294 MHz root, the audio_hdmi and audio_spdf interface gates and the audio_apll gate to the MT2701 AFE node, and reparent the AUDPLL mux to HADDS2PLL_98M so the HDMI audio serial clock path has a stable 294.912 MHz source. The clock names match the updated mediatek,mt2701-audio binding.

---
v3: no changes
v2: no changes

 arch/arm/boot/dts/mediatek/mt2701.dtsi | 21 ++++++++++++++++-----
 1 file changed, 16 insertions(+), 5 deletions(-)

index 128b87229f3d..80c8c7e6a422 100644
@@ -464,7 +464,11 @@ afe: audio-controller {
 				 <&audsys CLK_AUD_AFE_CONN>,
 				 <&audsys CLK_AUD_A1SYS>,
 				 <&audsys CLK_AUD_A2SYS>,
-				 <&audsys CLK_AUD_AFE_MRGIF>;
+				 <&audsys CLK_AUD_AFE_MRGIF>,
+				 <&topckgen CLK_TOP_HADDS2PLL_294M>,
+				 <&audsys CLK_AUD_HDMI>,
+				 <&audsys CLK_AUD_SPDF>,
+				 <&audsys CLK_AUD_APLL>;
 
 			clock-names = "infra_sys_audio_clk",
 				      "top_audio_mux1_sel",

@@ -499,15 +503,22 @@ afe: audio-controller {
 				      "audio_afe_conn_pd",
 				      "audio_a1sys_pd",
 				      "audio_a2sys_pd",
-				      "audio_mrgif_pd";
+				      "audio_mrgif_pd",
+				      "hadds2pll_294m",
+				      "audio_hdmi_pd",
+				      "audio_spdf_pd",
+				      "audio_apll_pd";
 
 			assigned-clocks = <&topckgen CLK_TOP_AUD_MUX1_SEL>,
 					  <&topckgen CLK_TOP_AUD_MUX2_SEL>,
 					  <&topckgen CLK_TOP_AUD_MUX1_DIV>,
-					  <&topckgen CLK_TOP_AUD_MUX2_DIV>;
+					  <&topckgen CLK_TOP_AUD_MUX2_DIV>,
+					  <&topckgen CLK_TOP_AUDPLL_MUX_SEL>;
 			assigned-clock-parents = <&topckgen CLK_TOP_AUD1PLL_98M>,
-						 <&topckgen CLK_TOP_AUD2PLL_90M>;
-			assigned-clock-rates = <0>, <0>, <49152000>, <45158400>;
+						 <&topckgen CLK_TOP_AUD2PLL_90M>,
+						 <0>, <0>,
+						 <&topckgen CLK_TOP_HADDS2PLL_98M>;
+			assigned-clock-rates = <0>, <0>, <49152000>, <45158400>, <0>;
 		};
 	};
 

2.54.0

Mirror the MT2701 change for the MT7623 SoC dtsi: add HADDS2PLL, audio_hdmi, audio_spdf and audio_apll to the AFE clocks list and reparent the AUDPLL mux to HADDS2PLL_98M. Required for HDMI audio on MT7623N boards via the shared mt2701 AFE driver.

---
v3: no changes
v2: no changes

 arch/arm/boot/dts/mediatek/mt7623.dtsi | 21 ++++++++++++++++-----
 1 file changed, 16 insertions(+), 5 deletions(-)

index 71ac2b94c6ba..4eb028ffee6f 100644
@@ -665,7 +665,11 @@ afe: audio-controller {
 				 <&audsys CLK_AUD_AFE_CONN>,
 				 <&audsys CLK_AUD_A1SYS>,
 				 <&audsys CLK_AUD_A2SYS>,
-				 <&audsys CLK_AUD_AFE_MRGIF>;
+				 <&audsys CLK_AUD_AFE_MRGIF>,
+				 <&topckgen CLK_TOP_HADDS2PLL_294M>,
+				 <&audsys CLK_AUD_HDMI>,
+				 <&audsys CLK_AUD_SPDF>,
+				 <&audsys CLK_AUD_APLL>;
 
 			clock-names = "infra_sys_audio_clk",
 				      "top_audio_mux1_sel",

@@ -700,15 +704,22 @@ afe: audio-controller {
 				      "audio_afe_conn_pd",
 				      "audio_a1sys_pd",
 				      "audio_a2sys_pd",
-				      "audio_mrgif_pd";
+				      "audio_mrgif_pd",
+				      "hadds2pll_294m",
+				      "audio_hdmi_pd",
+				      "audio_spdf_pd",
+				      "audio_apll_pd";
 
 			assigned-clocks = <&topckgen CLK_TOP_AUD_MUX1_SEL>,
 					  <&topckgen CLK_TOP_AUD_MUX2_SEL>,
 					  <&topckgen CLK_TOP_AUD_MUX1_DIV>,
-					  <&topckgen CLK_TOP_AUD_MUX2_DIV>;
+					  <&topckgen CLK_TOP_AUD_MUX2_DIV>,
+					  <&topckgen CLK_TOP_AUDPLL_MUX_SEL>;
 			assigned-clock-parents = <&topckgen CLK_TOP_AUD1PLL_98M>,
-						 <&topckgen CLK_TOP_AUD2PLL_90M>;
-			assigned-clock-rates = <0>, <0>, <49152000>, <45158400>;
+						 <&topckgen CLK_TOP_AUD2PLL_90M>,
+						 <0>, <0>,
+						 <&topckgen CLK_TOP_HADDS2PLL_98M>;
+			assigned-clock-rates = <0>, <0>, <49152000>, <45158400>, <0>;
 		};
 	};
 

2.54.0

Instantiate the mediatek,mt2701-hdmi-audio machine on the BananaPi BPI-R2, binding the AFE HDMI playback path to the on-chip HDMI transmitter acting as the generic HDMI codec.

---
v3: no changes
v2: no changes

 arch/arm/boot/dts/mediatek/mt7623n-bananapi-bpi-r2.dts | 7 +++++++
 1 file changed, 7 insertions(+)

index a37f3fa223c7..139a76764faa 100644
@@ -132,6 +132,13 @@ memory@80000000 {
 		device_type = "memory";
 		reg = <0 0x80000000 0 0x80000000>;
 	};
+
+	sound-hdmi {
+		compatible = "mediatek,mt7623n-hdmi-audio",
+			     "mediatek,mt2701-hdmi-audio";
+		mediatek,platform = <&afe>;
+		mediatek,audio-codec = <&hdmi0>;
+	};
 };
 
 &bls {

2.54.0

Applied to

https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound.git for-7.2

Thanks!

[1/9] ASoC: dt-bindings: mt2701-afe-pcm: add HDMI audio path clocks

      https://git.kernel.org/broonie/sound/c/7139d75a1ac1
[2/9] ASoC: dt-bindings: mediatek,mt2701-hdmi-audio: add MT2701 HDMI audio
      https://git.kernel.org/broonie/sound/c/069ac057ddaf
[3/9] ASoC: mediatek: mt2701: add AFE HDMI register definitions
      https://git.kernel.org/broonie/sound/c/3401cff9a9ef
[4/9] ASoC: mediatek: mt2701: add optional HDMI audio path clocks
      https://git.kernel.org/broonie/sound/c/06efb5f1b777
[5/9] ASoC: mediatek: mt2701: add HDMI audio memif, FE and BE DAIs
      https://git.kernel.org/broonie/sound/c/0e2f1d39c2bf
[6/9] ASoC: mediatek: mt2701: add machine driver for on-chip HDMI codec
      https://git.kernel.org/broonie/sound/c/4d9c6bbfed7d

All being well this means that it will be integrated into the linux-next tree (usually sometime in the next 24 hours) and sent to Linus during the next merge window (or sooner if it is a bug fix), however if problems are discovered then the patch may be dropped or reverted.

You may get further e-mails resulting from automated or manual testing and review of the tree, please engage with people reporting problems and send followup patches addressing any issues that are reported if needed.

If any updates are required or you are submitting further changes they should be sent as incremental updates against current git, existing patches will not be replaced.

Please add any relevant lists and maintainers to the CCs when replying to this mail.

Thanks,
Mark

Whole series is

I'll pick the devicetree bits after the ASoC and bindings bits get picked.

Cheers,
Angelo