Skip to contentSkip to conversation

iommu/arm-smmu-v3: Fix device crash on kdump kernel

PATCH Superseded Nicolin Chen 1 participant 7 messages Apr 25 – Apr 29

Subsystems (3)

v3 of 7 Superseded Latest is v7 →

lore
Share & tools
lore
#0 lore raw

v3 cover iommu/arm-smmu-v3: Fix device crash on kdump kernel

When transitioning to a kdump kernel, the primary kernel might have crashed while endpoint devices were actively bus-mastering DMA. Currently, the SMMU driver aggressively resets the hardware during probe by clearing CR0_SMMUEN and setting the Global Bypass Attribute (GBPA) to ABORT.

In a kdump scenario, this aggressive reset is highly destructive:
a) If GBPA is set to ABORT, in-flight DMA will be aborted, generating fatal PCIe AER or SErrors that may panic the kdump kernel
b) If GBPA is set to BYPASS, in-flight DMA targeting some IOVAs will bypass the SMMU and corrupt the physical memory at those 1:1 mapped IOVAs.

To safely absorb in-flight DMA, the kdump kernel must leave SMMUEN=1 intact and avoid modifying STRTAB_BASE. This allows HW to continue translating in- flight DMA using the crashed kernel's page tables until the endpoint device drivers probe and quiesce their respective hardware.

However, the ARM SMMUv3 architecture specification states that updating the SMMU_STRTAB_BASE register while SMMUEN == 1 is UNPREDICTABLE or ignored.

This leaves a kdump kernel no choice but to adopt the stream table from the crashed kernel.

In this series:
- Introduce an ARM_SMMU_OPT_KDUMP_ADOPT
- Skip SMMUEN and STRTAB_BASE resets in arm_smmu_device_reset()
- Skip EVENTQ and PRIQ setups including interrupts and their handlers
- Memremap the crashed kernel's stream tables into the kdump kernel [*]
- Defer any default domain attachment to retain STEs until device drivers explicitly request it.

[*] This only works on a coherent SMMU.

For non-ARM_SMMU_OPT_KDUMP_ADOPT cases, keep a status quo since the commit 3f54c447df34f ("iommu/arm-smmu-v3: Don't disable SMMU in kdump kernel"):
full reset followed by driver-initiated reattach, potentially rejecting any in-flight DMA.

Note that the series requires Jason's work that was merged in v6.12: commit 85196f54743d ("iommu/arm-smmu-v3: Reorganize struct arm_smmu_strtab_cfg"). I have a backported version that is verified with a v6.8 kernel. I can send if we see a strong need after this version is accepted.

This is on Github:
https://github.com/nicolinc/iommufd/commits/smmuv3_kdump-v3

Changelog
v3
* s/OPT_KDUMP/OPT_KDUMP_ADOPT
* Do not adopt if GERROR_SFM_ERR
* Retain CR0_ATSCHK beside CR0_SMMUEN
* Clear latched GERROR bits (e.g. CMDQ_ERR)
* Assert ARM_SMMU_FEAT_COHERENCY in adopt functions
* Add STE.Cfg check in arm_smmu_is_attach_deferred()
* Fix validations on return codes from devm_memremap()
* Sanitize crashed kernel register values in adopt functions
* Drop unnecessary l2ptrs guard in arm_smmu_is_attach_deferred()
* Don't enable PRIQ/EVTQ irqs and guard the irq functions for combined irq cases
v2
https://lore.kernel.org/all/[email protected]/
* Add warning in non-coherent SMMU cases
* Keep eventq/priq disabled v.s. enabling-and-disabling-later
* Check KDUMP option in the beginning of arm_smmu_device_reset()
* Validate STRTAB format matches HW capability instead of forcing flags
v1:
https://lore.kernel.org/all/[email protected]/

Nicolin Chen (5):
iommu/arm-smmu-v3: Add arm_smmu_adopt_strtab() for kdump iommu/arm-smmu-v3: Implement is_attach_deferred() for kdump iommu/arm-smmu-v3: Retain CR0_SMMUEN during kdump device reset iommu/arm-smmu-v3: Skip EVTQ/PRIQ setup in kdump kernel iommu/arm-smmu-v3: Detect ARM_SMMU_OPT_KDUMP_ADOPT in probe()

 drivers/iommu/arm/arm-smmu-v3/arm-smmu-v3.h |   1 +
 drivers/iommu/arm/arm-smmu-v3/arm-smmu-v3.c | 358 ++++++++++++++++++--
 2 files changed, 338 insertions(+), 21 deletions(-)
Signature · 1 line
2.43.0
#1 lore raw

PATCH v3 1/5 iommu/arm-smmu-v3: Add arm_smmu_adopt_strtab() for kdump

When transitioning to a kdump kernel, the primary kernel might have crashed while endpoint devices were actively bus-mastering DMA. Currently, the SMMU driver aggressively resets the hardware during probe by clearing CR0_SMMUEN and setting the Global Bypass Attribute (GBPA) to ABORT.

In a kdump scenario, this aggressive reset is highly destructive:
a) If GBPA is set to ABORT, in-flight DMA will be aborted, generating fatal PCIe AER or SErrors that may panic the kdump kernel
b) If GBPA is set to BYPASS, in-flight DMA targeting some IOVAs will bypass the SMMU and corrupt the physical memory at those 1:1 mapped IOVAs.

To safely absorb in-flight DMAs, a kdump kernel will have to leave SMMUEN=1 intact and avoid modifying STRTAB_BASE, allowing HW to continue translating in-flight DMAs reusing the crashed kernel's page tables until the endpoint device drivers probe and quiesce their respective hardware.

However, the ARM SMMUv3 architecture specification states that updating the SMMU_STRTAB_BASE register while SMMUEN == 1 is UNPREDICTABLE or ignored.

This leaves a kdump kernel no choice but to adopt the stream table from the crashed kernel.

Introduce ARM_SMMU_OPT_KDUMP_ADOPT and its pairing arm_smmu_adopt_strtab(), which does memremap on all the stream tables extracted from STRTAB_BASE and STRTAB_BASE_CFG. This new option will be set in arm_smmu_device_hw_probe() in a following change.

Note that the adoption of the crashed kernel's stream table follows certain strict rules, since the old stream table might be compromised. Thus, apply a series of validations against the values read from the registers. If any address or size doesn't pass the test, it means the stream table cannot be trusted, so toss it completely.

Fixes b63b3439b856 ("iommu/arm-smmu-v3: Abort all transactions if SMMU is enabled in kdump kernel")
Cc [email protected] # v6.12+
---
 drivers/iommu/arm/arm-smmu-v3/arm-smmu-v3.h |   1 +
 drivers/iommu/arm/arm-smmu-v3/arm-smmu-v3.c | 187 ++++++++++++++++++++
 2 files changed, 188 insertions(+)
drivers/iommu/arm/arm-smmu-v3/arm-smmu-v3.h +1 -0
index ef42df4753ec4..cd60b692c3901 100644
@@ -861,6 +861,7 @@ struct arm_smmu_device {
 #define ARM_SMMU_OPT_MSIPOLL		(1 << 2)
 #define ARM_SMMU_OPT_CMDQ_FORCE_SYNC	(1 << 3)
 #define ARM_SMMU_OPT_TEGRA241_CMDQV	(1 << 4)
+#define ARM_SMMU_OPT_KDUMP_ADOPT	(1 << 5)
 	u32				options;
 
 	struct arm_smmu_cmdq		cmdq;
drivers/iommu/arm/arm-smmu-v3/arm-smmu-v3.c +187 -0

209 lines not on this page · raw message

Signature · 1 line
2.43.0
#2 lore raw

PATCH v3 2/5 iommu/arm-smmu-v3: Implement is_attach_deferred() for kdump

In reply to Nicolin Chen

Though the kdump kernel adopts the crashed kernel's stream table, the iommu core will still try to attach each probed device to a default domain, which overwrites the adopted STE and breaks in-flight DMA from that device.

Implement an is_attach_deferred() callback to prevent this. For each device that has STE.V=1 and STE.Cfg!=Abort in the adopted table, defer the default domain attachment, until the device driver explicitly requests it.

Fixes b63b3439b856 ("iommu/arm-smmu-v3: Abort all transactions if SMMU is enabled in kdump kernel")
Cc [email protected] # v6.12+
---
 drivers/iommu/arm/arm-smmu-v3/arm-smmu-v3.c | 24 +++++++++++++++++++++
 1 file changed, 24 insertions(+)
drivers/iommu/arm/arm-smmu-v3/arm-smmu-v3.c +24 -0
index bf292e1e0c323..8423bcc4be69e 100644
@@ -4213,6 +4213,29 @@ static void arm_smmu_remove_master(struct arm_smmu_master *master)
 	kfree(master->build_invs);
 }
 
+static bool arm_smmu_is_attach_deferred(struct device *dev)
+{
+	struct arm_smmu_master *master = dev_iommu_priv_get(dev);
+	struct arm_smmu_device *smmu = master->smmu;
+	int i;
+
+	if (!(smmu->options & ARM_SMMU_OPT_KDUMP_ADOPT))
+		return false;
+
+	for (i = 0; i < master->num_streams; i++) {
+		struct arm_smmu_ste *ste =
+			arm_smmu_get_step_for_sid(smmu, master->streams[i].id);
+		u64 ent0 = le64_to_cpu(ste->data[0]);
+
+		/* Defer only when there might be in-flight DMAs */
+		if ((ent0 & STRTAB_STE_0_V) &&
+		    FIELD_GET(STRTAB_STE_0_CFG, ent0) != STRTAB_STE_0_CFG_ABORT)
+			return true;
+	}
+
+	return false;
+}
+
 static struct iommu_device *arm_smmu_probe_device(struct device *dev)
 {
 	int ret;
@@ -4375,6 +4398,7 @@ static const struct iommu_ops arm_smmu_ops = {
 	.hw_info		= arm_smmu_hw_info,
 	.domain_alloc_sva       = arm_smmu_sva_domain_alloc,
 	.domain_alloc_paging_flags = arm_smmu_domain_alloc_paging_flags,
+	.is_attach_deferred	= arm_smmu_is_attach_deferred,
 	.probe_device		= arm_smmu_probe_device,
 	.release_device		= arm_smmu_release_device,
 	.device_group		= arm_smmu_device_group,
Signature · 1 line
2.43.0
#3 lore raw

PATCH v3 3/5 iommu/arm-smmu-v3: Retain CR0_SMMUEN during kdump device reset

In reply to Nicolin Chen

When ARM_SMMU_OPT_KDUMP_ADOPT is detected, do not disable SMMUEN and skip the CR1/CR2/STRTAB_BASE update sequence in arm_smmu_device_reset(). Those register writes are all CONSTRAINED UNPREDICTABLE while CR0_SMMUEN==1, so leaving them intact lets in-flight DMAs continue to be translated by the adopted stream table.

Initialize 'enables' to 0 so it can carry CR0_SMMUEN in kdump case. Then, preserve that when enabling the command queue.

Clear latched gerror bits if necessary.

Fixes b63b3439b856 ("iommu/arm-smmu-v3: Abort all transactions if SMMU is enabled in kdump kernel")
Cc [email protected] # v6.12+
---
 drivers/iommu/arm/arm-smmu-v3/arm-smmu-v3.c | 47 +++++++++++++++++++--
 1 file changed, 44 insertions(+), 3 deletions(-)
drivers/iommu/arm/arm-smmu-v3/arm-smmu-v3.c +44 -3
index 8423bcc4be69e..b6aade469a6b6 100644
@@ -5017,11 +5017,28 @@ static void arm_smmu_write_strtab(struct arm_smmu_device *smmu)
 static int arm_smmu_device_reset(struct arm_smmu_device *smmu)
 {
 	int ret;
-	u32 reg, enables;
+	u32 reg, enables = 0;
 	struct arm_smmu_cmdq_ent cmd;
 
-	/* Clear CR0 and sync (disables SMMU and queue processing) */
 	reg = readl_relaxed(smmu->base + ARM_SMMU_CR0);
+
+	/*
+	 * In a kdump case (set when CR0_SMMUEN=1 and !GERROR_SFM_ERR), retain
+	 * CR0_SMMUEN to avoid aborting in-flight DMA, and CR0_ATSCHK to carry
+	 * on the ATS-check policy.
+	 *
+	 * According to spec, updating STRTAB_BASE/CR1/CR2 when CR0_SMMUEN=1 is
+	 * CONSTRAINED UNPREDICTABLE. So, skip those register updates and rely
+	 * on the adopted stream table from the crashed kernel.
+	 */
+	if (smmu->options & ARM_SMMU_OPT_KDUMP_ADOPT) {
+		dev_info(smmu->dev,
+			 "kdump: retaining SMMUEN for in-flight DMA\n");
+		enables = reg & (CR0_SMMUEN | CR0_ATSCHK);
+		goto reset_queues;
+	}
+
+	/* Clear CR0 and sync (disables SMMU and queue processing) */
 	if (reg & CR0_SMMUEN) {
 		dev_warn(smmu->dev, "SMMU currently enabled! Resetting...\n");
 		arm_smmu_update_gbpa(smmu, GBPA_ABORT, 0);
@@ -5051,12 +5068,36 @@ static int arm_smmu_device_reset(struct arm_smmu_device *smmu)
 	/* Stream table */
 	arm_smmu_write_strtab(smmu);
 
+reset_queues:
+	if (smmu->options & ARM_SMMU_OPT_KDUMP_ADOPT) {
+		/* Disable queues since arm_smmu_device_disable() was skipped */
+		ret = arm_smmu_write_reg_sync(smmu, enables, ARM_SMMU_CR0,
+					      ARM_SMMU_CR0ACK);
+		if (ret) {
+			dev_err(smmu->dev, "failed to disable queues\n");
+			return ret;
+		}
+	}
+
+	/*
+	 * GERROR bits are latched. Read after queue disabling so that unhandled
+	 * errors would be visible. Ack everything prior to re-enabling the CMDQ
+	 * as a stale CMDQ_ERR would halt the CMDQ and new command will timeout.
+	 */
+	if (is_kdump_kernel()) {
+		u32 gerror = readl_relaxed(smmu->base + ARM_SMMU_GERROR);
+		u32 gerrorn = readl_relaxed(smmu->base + ARM_SMMU_GERRORN);
+
+		if ((gerror ^ gerrorn) & GERROR_ERR_MASK)
+			writel(gerror, smmu->base + ARM_SMMU_GERRORN);
+	}
+
 	/* Command queue */
 	writeq_relaxed(smmu->cmdq.q.q_base, smmu->base + ARM_SMMU_CMDQ_BASE);
 	writel_relaxed(smmu->cmdq.q.llq.prod, smmu->base + ARM_SMMU_CMDQ_PROD);
 	writel_relaxed(smmu->cmdq.q.llq.cons, smmu->base + ARM_SMMU_CMDQ_CONS);
 
-	enables = CR0_CMDQEN;
+	enables |= CR0_CMDQEN;
 	ret = arm_smmu_write_reg_sync(smmu, enables, ARM_SMMU_CR0,
 				      ARM_SMMU_CR0ACK);
 	if (ret) {
Signature · 1 line
2.43.0
#4 lore raw

PATCH v3 4/5 iommu/arm-smmu-v3: Skip EVTQ/PRIQ setup in kdump kernel

In reply to Nicolin Chen

In kdump cases, the crashed kernel's CDs and page tables can be corrupted, which could trigger event spamming. Also, we cannot serve page requests.

Skip the EVTQ/PRIQ setup entirely rather than enabling then disabling them.

Skip the IRQ setup and guard their thread functions as well.

Also add some inline comments explaining that.

Fixes b63b3439b856 ("iommu/arm-smmu-v3: Abort all transactions if SMMU is enabled in kdump kernel")
Cc [email protected] # v6.12+
---
 drivers/iommu/arm/arm-smmu-v3/arm-smmu-v3.c | 66 +++++++++++++++------
 1 file changed, 48 insertions(+), 18 deletions(-)
drivers/iommu/arm/arm-smmu-v3/arm-smmu-v3.c +48 -18
index b6aade469a6b6..f0ab0b640a3bb 100644
@@ -2269,6 +2269,14 @@ static irqreturn_t arm_smmu_evtq_thread(int irq, void *dev)
 	static DEFINE_RATELIMIT_STATE(rs, DEFAULT_RATELIMIT_INTERVAL,
 				      DEFAULT_RATELIMIT_BURST);
 
+	/*
+	 * A combined IRQ might call into this function with the queue disabled.
+	 * E.g. kdump, where stale HW PROD vs SW CONS would drive a bogus drain
+	 * and a CONS write to a disabled queue.
+	 */
+	if (!(readl_relaxed(smmu->base + ARM_SMMU_CR0) & CR0_EVTQEN))
+		return IRQ_HANDLED;
+
 	do {
 		while (!queue_remove_raw(q, evt)) {
 			arm_smmu_decode_event(smmu, evt, &event);
@@ -2337,6 +2345,14 @@ static irqreturn_t arm_smmu_priq_thread(int irq, void *dev)
 	struct arm_smmu_ll_queue *llq = &q->llq;
 	u64 evt[PRIQ_ENT_DWORDS];
 
+	/*
+	 * A combined IRQ might call into this function with the queue disabled.
+	 * E.g. kdump, where stale HW PROD vs SW CONS would drive a bogus drain
+	 * and a CONS write to a disabled queue.
+	 */
+	if (!(readl_relaxed(smmu->base + ARM_SMMU_CR0) & CR0_PRIQEN))
+		return IRQ_HANDLED;
+
 	do {
 		while (!queue_remove_raw(q, evt))
 			arm_smmu_handle_ppr(smmu, evt);
@@ -4941,7 +4957,10 @@ static void arm_smmu_setup_unique_irqs(struct arm_smmu_device *smmu)
 static int arm_smmu_setup_irqs(struct arm_smmu_device *smmu)
 {
 	int ret, irq;
-	u32 irqen_flags = IRQ_CTRL_EVTQ_IRQEN | IRQ_CTRL_GERROR_IRQEN;
+	u32 irqen_flags = IRQ_CTRL_GERROR_IRQEN;
+
+	if (!is_kdump_kernel())
+		irqen_flags |= IRQ_CTRL_EVTQ_IRQEN;
 
 	/* Disable IRQs first */
 	ret = arm_smmu_write_reg_sync(smmu, 0, ARM_SMMU_IRQ_CTRL,
@@ -4967,7 +4986,7 @@ static int arm_smmu_setup_irqs(struct arm_smmu_device *smmu)
 	} else
 		arm_smmu_setup_unique_irqs(smmu);
 
-	if (smmu->features & ARM_SMMU_FEAT_PRI)
+	if (!is_kdump_kernel() && (smmu->features & ARM_SMMU_FEAT_PRI))
 		irqen_flags |= IRQ_CTRL_PRIQ_IRQEN;
 
 	/* Enable interrupt generation on the SMMU */
@@ -5118,21 +5137,35 @@ static int arm_smmu_device_reset(struct arm_smmu_device *smmu)
 	cmd.opcode = CMDQ_OP_TLBI_NSNH_ALL;
 	arm_smmu_cmdq_issue_cmd_with_sync(smmu, &cmd);
 
-	/* Event queue */
-	writeq_relaxed(smmu->evtq.q.q_base, smmu->base + ARM_SMMU_EVTQ_BASE);
-	writel_relaxed(smmu->evtq.q.llq.prod, smmu->page1 + ARM_SMMU_EVTQ_PROD);
-	writel_relaxed(smmu->evtq.q.llq.cons, smmu->page1 + ARM_SMMU_EVTQ_CONS);
-
-	enables |= CR0_EVTQEN;
-	ret = arm_smmu_write_reg_sync(smmu, enables, ARM_SMMU_CR0,
-				      ARM_SMMU_CR0ACK);
-	if (ret) {
-		dev_err(smmu->dev, "failed to enable event queue\n");
-		return ret;
+	/*
+	 * Event queue
+	 *
+	 * Do not enable in a kdump case, as the crashed kernel's CDs and page
+	 * tables might be corrupted, triggering event spamming.
+	 */
+	if (!is_kdump_kernel()) {
+		writeq_relaxed(smmu->evtq.q.q_base,
+			       smmu->base + ARM_SMMU_EVTQ_BASE);
+		writel_relaxed(smmu->evtq.q.llq.prod,
+			       smmu->page1 + ARM_SMMU_EVTQ_PROD);
+		writel_relaxed(smmu->evtq.q.llq.cons,
+			       smmu->page1 + ARM_SMMU_EVTQ_CONS);
+
+		enables |= CR0_EVTQEN;
+		ret = arm_smmu_write_reg_sync(smmu, enables, ARM_SMMU_CR0,
+					      ARM_SMMU_CR0ACK);
+		if (ret) {
+			dev_err(smmu->dev, "failed to enable event queue\n");
+			return ret;
+		}
 	}
 
-	/* PRI queue */
-	if (smmu->features & ARM_SMMU_FEAT_PRI) {
+	/*
+	 * PRI queue
+	 *
+	 * Do not enable in a kdump case, as we cannot serve page requests.
+	 */
+	if (!is_kdump_kernel() && (smmu->features & ARM_SMMU_FEAT_PRI)) {
 		writeq_relaxed(smmu->priq.q.q_base,
 			       smmu->base + ARM_SMMU_PRIQ_BASE);
 		writel_relaxed(smmu->priq.q.llq.prod,
@@ -5165,9 +5198,6 @@ static int arm_smmu_device_reset(struct arm_smmu_device *smmu)
 		return ret;
 	}
 
-	if (is_kdump_kernel())
-		enables &= ~(CR0_EVTQEN | CR0_PRIQEN);
-
 	/* Enable the SMMU interface */
 	enables |= CR0_SMMUEN;
 	ret = arm_smmu_write_reg_sync(smmu, enables, ARM_SMMU_CR0,
Signature · 1 line
2.43.0
#5 lore raw

PATCH v3 5/5 iommu/arm-smmu-v3: Detect ARM_SMMU_OPT_KDUMP_ADOPT in probe()

In reply to Nicolin Chen

arm_smmu_device_hw_probe() runs before arm_smmu_init_structures(), so it's natural to decide whether the kdump kernel must adopt the crashed kernel's stream table.

Given that memremap is used to adopt the old stream table, set this option only on a coherent SMMU.

And make sure SMMU isn't in Service Failure Mode.

Fixes b63b3439b856 ("iommu/arm-smmu-v3: Abort all transactions if SMMU is enabled in kdump kernel")
Cc [email protected] # v6.12+
---
 drivers/iommu/arm/arm-smmu-v3/arm-smmu-v3.c | 34 +++++++++++++++++++++
 1 file changed, 34 insertions(+)
drivers/iommu/arm/arm-smmu-v3/arm-smmu-v3.c +34 -0
index f0ab0b640a3bb..35aceb22d5c89 100644
@@ -5288,6 +5288,36 @@ static void arm_smmu_get_httu(struct arm_smmu_device *smmu, u32 reg)
 			  hw_features, fw_features);
 }
 
+static void arm_smmu_device_hw_probe_kdump(struct arm_smmu_device *smmu)
+{
+	u32 gerror, gerrorn, active;
+
+	/*
+	 * If SMMU is already active in kdump case, there could be in-flight DMA
+	 * from devices initiated by the crashed kernel.
+	 */
+	if (!(readl_relaxed(smmu->base + ARM_SMMU_CR0) & CR0_SMMUEN))
+		return;
+
+	/* For now, only support a coherent SMMU that works with MEMREMAP_WB */
+	if (!(smmu->features & ARM_SMMU_FEAT_COHERENCY)) {
+		dev_warn(smmu->dev,
+			 "kdump: non-coherent SMMU can't adopt stream table\n");
+		return;
+	}
+
+	gerror = readl_relaxed(smmu->base + ARM_SMMU_GERROR);
+	gerrorn = readl_relaxed(smmu->base + ARM_SMMU_GERRORN);
+	active = gerror ^ gerrorn;
+	if (active & GERROR_SFM_ERR) {
+		dev_warn(smmu->dev,
+			 "kdump: SMMU in Service Failure Mode, must reset\n");
+		return;
+	}
+
+	smmu->options |= ARM_SMMU_OPT_KDUMP_ADOPT;
+}
+
 static int arm_smmu_device_hw_probe(struct arm_smmu_device *smmu)
 {
 	u32 reg;
@@ -5502,6 +5532,10 @@ static int arm_smmu_device_hw_probe(struct arm_smmu_device *smmu)
 
 	dev_info(smmu->dev, "oas %lu-bit (features 0x%08x)\n",
 		 smmu->oas, smmu->features);
+
+	if (is_kdump_kernel())
+		arm_smmu_device_hw_probe_kdump(smmu);
+
 	return 0;
 }
 
Signature · 1 line
2.43.0
#6 lore raw
In reply to Nicolin Chen
Quoted 16 lines · Nicolin Chen

This is on Github:
https://github.com/nicolinc/iommufd/commits/smmuv3_kdump-v3

Changelog
v3
* s/OPT_KDUMP/OPT_KDUMP_ADOPT
* Do not adopt if GERROR_SFM_ERR
* Retain CR0_ATSCHK beside CR0_SMMUEN
* Clear latched GERROR bits (e.g. CMDQ_ERR)
* Assert ARM_SMMU_FEAT_COHERENCY in adopt functions
* Add STE.Cfg check in arm_smmu_is_attach_deferred()
* Fix validations on return codes from devm_memremap()
* Sanitize crashed kernel register values in adopt functions
* Drop unnecessary l2ptrs guard in arm_smmu_is_attach_deferred()
* Don't enable PRIQ/EVTQ irqs and guard the irq functions for combined irq cases

https://sashiko.dev/#/patchset/cover.1777150307.git.nicolinc%40nvidia.com

Sashiko pointed out a few more comments on v3. Most of them are interesting to address.

I have made some updates to the series and will send v4 after a final check.

Thanks
Nicolin