Toshiba PS/2 touchpad on 2.6.X not working along bottom and right sides
Hello.
I recently installed Linux 2.6.10 on my Gateway Solo 2500 notebook after using it happily with 2.4.27 (aside from some ACPI sleeping issues). Since installing the new kernel, I've noticed an odd problem with the Toshiba PS/2 touchpad which is used as a cursor. If I move my finger left and right along the 'bottom' portion of the touchpad or up and down along the right side, there is no movement from the mouse cursor at all. This behavior shows up using gdm and XFree86. Running 'xev' produces no output when these sides are used. However, if I move my finger left-right along the top side or up-down along the left side, the cursor moves just fine. Tapping the pad to click in the non-working areas and moving the finger from outside of these areas and then into them, however, works fine.
It's almost as if the portion of the pad that is sensitive to movement has been shifted up and to the left (except that clicking in and dragging into this area works).
I think this might have something to do with the drag-lock function because if I move the cursor from, say, the center of the pad and down to the lower side, the cursor will begin to move downward when my finger gets into the portion of the pad that does not function 100%. (This is really only a wild-ass guess, though.)
I've tried killing gdm and loading up my old 2.4 kernels to be sure it's not something else. I've also tried kernels 2.6.5.and 2.6.0 and a clean 2.6.10 tree (without the acpi and swsusp2 patches that I want) to be sure that this isn't likely to be something that just cropped up recently. The old (good, working) behavior is found in a 2.4 kernel and some new (bad, faulty) behavior is found in the 2.6 kernels that I've tried. I've also tried booting with acpi=off to no avail.
I realize this problem may seem odd, but I've described it as best I can. I also realize that other people are having issues with pointing devices and keyboards, so this could just be a related problem that will be fixed when those others are fixed as well.
Thanks.
Signature · 1 line
-Andy
Quoted 14 lines · Andrew Haninger
Hello.
I recently installed Linux 2.6.10 on my Gateway Solo 2500 notebook after using it happily with 2.4.27 (aside from some ACPI sleeping issues). Since installing the new kernel, I've noticed an odd problem with the Toshiba PS/2 touchpad which is used as a cursor. If I move my finger left and right along the 'bottom' portion of the touchpad or up and down along the right side, there is no movement from the mouse cursor at all. This behavior shows up using gdm and XFree86. Running 'xev' produces no output when these sides are used. However, if I move my finger left-right along the top side or up-down along the left side, the cursor moves just fine. Tapping the pad to click in the non-working areas and moving the finger from outside of these areas and then into them, however, works fine
What does dmesg and /proc/bus/input/devices say about your touchpad?
Signature · 1 line
Dmitry
A message that is not in the archive (sent off-list or not yet received): [email protected]
I forgot to CC the list in case anyone else was interested in this information as well.
Sorry about the dupe, Dmitry.
-Andy
---------- Forwarded message ----------
From: Andrew Haninger <[email protected]>
Date: Thu, 30 Dec 2004 09:53:33 -0500
Subject: Re: Toshiba PS/2 touchpad on 2.6.X not working along bottom and right sides
To: Dmitry Torokhov <[email protected]>
Quoted 13 lines
Quoted 4 lines
I recently installed Linux 2.6.10 on my Gateway Solo 2500 notebook after using it happily with 2.4.27 (aside from some ACPI sleeping issues). Since installing the new kernel, I've noticed an odd problem with the Toshiba PS/2 touchpad which is used as a cursor. If I move my
Quoted 8 lines
finger left and right along the 'bottom' portion of the touchpad or up and down along the right side, there is no movement from the mouse cursor at all. This behavior shows up using gdm and XFree86. Running 'xev' produces no output when these sides are used. However, if I move my finger left-right along the top side or up-down along the left side, the cursor moves just fine. Tapping the pad to click in the non-working areas and moving the finger from outside of these areas and then into them, however, works fine
Quoted 1 line
What does dmesg and
/proc/bus/input/devicessay about your touchpad?
root@laptop:~# dmesg | grep "PS" mice: PS/2 mouse device common for all mice input: PS2T++ Logitech TouchPad 3 on isa0060/serio1
root@laptop:~# cat /proc/bus/input/devices I: Bus=0011 Vendor=0002 Product=0003 Version=0061 N: Name="PS2T++ Logitech TouchPad 3" P: Phys=isa0060/serio1/input0 H: Handlers=mouse0 B: EV=7 B: KEY=70000 0 0 0 0 0 0 0 0 B: REL=143
Actually, this was more information than I was able to find earlier. I'll be able to do some more useful searches now.
Thanks.
--
Andy
Andrew Haninger <[email protected]> writes:
This might be a touchpad that simulates the scroll wheel on the right side and horizontal scrolling on the bottom.
Does your touchpad emit mouse button events when touching on the right / bottom side?
I have a Toshiba Satellite with another touchpad (a Synaptics) and this can be programmed to do so. I'd think that Toshiba noadays uses touchpads that have this hard-coded (maybe there is a command to turn this on/off).
Regards
Henning
Quoted 53 lines
I forgot to CC the list in case anyone else was interested in this information as well.
Sorry about the dupe, Dmitry.
-Andy
---------- Forwarded message ----------
From: Andrew Haninger <[email protected]>
Date: Thu, 30 Dec 2004 09:53:33 -0500
Subject: Re: Toshiba PS/2 touchpad on 2.6.X not working along bottom and right sides
To: Dmitry Torokhov <[email protected]>Quoted 13 lines
Quoted 4 lines
I recently installed Linux 2.6.10 on my Gateway Solo 2500 notebook after using it happily with 2.4.27 (aside from some ACPI sleeping issues). Since installing the new kernel, I've noticed an odd problem with the Toshiba PS/2 touchpad which is used as a cursor. If I move my
Quoted 8 lines
finger left and right along the 'bottom' portion of the touchpad or up and down along the right side, there is no movement from the mouse cursor at all. This behavior shows up using gdm and XFree86. Running 'xev' produces no output when these sides are used. However, if I move my finger left-right along the top side or up-down along the left side, the cursor moves just fine. Tapping the pad to click in the non-working areas and moving the finger from outside of these areas and then into them, however, works fine
Quoted 1 line
What does dmesg and
/proc/bus/input/devicessay about your touchpad?root@laptop:~# dmesg | grep "PS" mice: PS/2 mouse device common for all mice input: PS2T++ Logitech TouchPad 3 on isa0060/serio1root@laptop:~# cat /proc/bus/input/devices I: Bus=0011 Vendor=0002 Product=0003 Version=0061 N: Name="PS2T++ Logitech TouchPad 3" P: Phys=isa0060/serio1/input0 H: Handlers=mouse0 B: EV=7 B: KEY=70000 0 0 0 0 0 0 0 0 B: REL=143Actually, this was more information than I was able to find earlier. I'll be able to do some more useful searches now.
Thanks.
--
Andy
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Signature · 10 lines
Dipl.-Inf. (Univ.) Henning P. Schmiedehausen INTERMETA GmbH [email protected] +49 9131 50 654 0 http://www.intermeta.de/ RedHat Certified Engineer -- Jakarta Turbine Development -- hero for hire Linux, Java, perl, Solaris -- Consulting, Training, Development What is more important to you... [ ] Product Security or [ ] Quality of Sales and Marketing Support -- actual question from a Microsoft customer survey
Quoted 10 lines · Henning P. Schmiedehausen
This might be a touchpad that simulates the scroll wheel on the right side and horizontal scrolling on the bottom.
Does your touchpad emit mouse button events when touching on the right / bottom side?
I have a Toshiba Satellite with another touchpad (a Synaptics) and this can be programmed to do so. I'd think that Toshiba noadays uses touchpads that have this hard-coded (maybe there is a command to turn this on/off).
I have a ThinkPad T42 that can do this, as well, and this is what I thought when I first encountered this problem. However, I've had this Gateway laptop since about 1999 and it hasn't done this since. Not in 2.2 or 2.4.
Also, like I said, xev produced no output when I touched and dragged in the offending areas.
If this really is an added feature and there's a way to turn it off, that would be okay. Having it off by default would be best since it's seemingly a changed behavior between one kernel version and another (also, I hate that feature :) ).
--
Andy
Quoted 17 lines · Andrew Haninger
Quoted 10 lines · Henning P. Schmiedehausen
This might be a touchpad that simulates the scroll wheel on the right side and horizontal scrolling on the bottom.
Does your touchpad emit mouse button events when touching on the right / bottom side?
I have a Toshiba Satellite with another touchpad (a Synaptics) and this can be programmed to do so. I'd think that Toshiba noadays uses touchpads that have this hard-coded (maybe there is a command to turn this on/off).
I have a ThinkPad T42 that can do this, as well, and this is what I thought when I first encountered this problem. However, I've had this Gateway laptop since about 1999 and it hasn't done this since. Not in 2.2 or 2.4.
Quoted 8 lines
Also, like I said, xev produced no output when I touched and dragged in the offending areas.
If this really is an added feature and there's a way to turn it off, that would be okay. Having it off by default would be best since it's seemingly a changed behavior between one kernel version and another (also, I hate that feature :) ).
Yes, you can. Booting with psmouse.proto=bare will force the touchpad into standard PS/2 mode. You may also try booting with psmouse.proto=imps and psmouse.proto=exps - maybe one of these 2 will give you virtual scrolling.
If psmouse is compiled as a module you will have to add
options psmouse proto=bare
to your /etc/modprobe.conf
Btw, what device/protocol are you using in X? I'd advise setting it to "dev/input/mice" and "ExplorerPS/2" so if your touchad is indeed sending scroll events X would use them. Could you post your config, please?
Thanks!
Signature · 1 line
Dmitry
A message that is not in the archive (sent off-list or not yet received): [email protected]
Logitech PS/2 touchpad on 2.6.X not working along bottom and right sides.
And again, the previously-unforwarded-to-the-list bit.
-Andy
Quoted 7 lines
Yes, you can. Booting with psmouse.proto=bare will force the touchpad into standard PS/2 mode. You may also try booting with psmouse.proto=imps and psmouse.proto=exps - maybe one of these 2 will give you virtual scrolling.
If psmouse is compiled as a module you will have to add
Quoted 8 lines
options psmouse proto=bare
to your
/etc/modprobe.confBtw, what device/protocol are you using in X? I'd advise setting it to "dev/input/mice" and "ExplorerPS/2" so if your touchad is indeed sending scroll events X would use them. Could you post your config, please?
I'm using the /dev/mouse device for X with protocol 'auto'.
Here's the relevant portion of my XF86Config:
Section "InputDevice"
Identifier "Mouse0"
Driver "mouse"
Option "Protocol" "auto"
Option "Device" "/dev/mouse"EndSection
Unfortunately, I'm not currently physically at the machine (I only have ssh access currently), so I can't try this stuff right away. However, I will try your suggestions when I'm next at the machine later today.
(Also, I'm now realizing that my subject for this thread was wrong, so I've edited it a bit.)
(I'm replying to this message to keep it inside the original thread. It should be noted that the subject is wrong and that it turns out that the mouse is actually from Logitech and not Toshiba. Duh.)
Quoted 7 lines
Yes, you can. Booting with psmouse.proto=bare will force the touchpad into standard PS/2 mode. You may also try booting with psmouse.proto=imps and psmouse.proto=exps - maybe one of these 2 will give you virtual scrolling.
If psmouse is compiled as a module you will have to add
Quoted 8 lines
options psmouse proto=bare
to your
/etc/modprobe.confBtw, what device/protocol are you using in X? I'd advise setting it to "dev/input/mice" and "ExplorerPS/2" so if your touchad is indeed sending scroll events X would use them. Could you post your config, please?
Thanks, Dmitry. Setting proto=bare has returned the touchpad to it's original behavior.
Just to be clear, here's what I've done:
If I compiled the psmouse driver into the kernel, I added a line to my /etc/lilo.conf that looks like:
append="other_driver=option psmouse.proto=bare"
(the psmouse.proto=bare part is the only part really needed).
If I compiled the psmouse driver as a module (psmouse.o), then I added the following to my /etc/modprobe.conf:
options psmouse proto=bare
then I can just 'modprobe psmouse' and the driver is installed.
Using the other options (imps and exps) didn't change the behavior much. I had some strange issues with the cursor being occasionally moved to the upper-right corner of the screen very quickly when I dragged in the lower and the right sides of the touchpad. This behavior, however, was not (yet) reproducible. If I can figure out how to reproduce it reliably, I'll note it later.
Thanks.
-Andy
Quoted 6 lines
Using the other options (imps and exps) didn't change the behavior much. I had some strange issues with the cursor being occasionally moved to the upper-right corner of the screen very quickly when I dragged in the lower and the right sides of the touchpad. This behavior, however, was not (yet) reproducible. If I can figure out how to reproduce it reliably, I'll note it later.
For what it's worth, I still haven't found exactly what is causing this problem, but it has shown up more than once. It seems that it might have something to do with repeatedly loading and unloading the psmouse driver using different protocol options (proto=bare|imps|exps) and loading and unloading gpm (I said gdm previously, which was a mistake) using different -t (type) options (ps2|imps2|auto) and/or different mouse devices (/dev/mouse or /dev/input/mice). I've done lots of things to try to reproduce this behavior, but nothing yet seems to make it happen every time.
I haven't used the laptop 'normally' very much yet, so I don't know if this problem shows up in normal use or just under strange circumstances like setup and testing.
When it does show up, the mouse cursor moves quickly up to the upper-right corner of the display - be it the X display or on the console with gpm - when the lower or right sides of the touchpad are used. Using the other areas of the touchpad produces normal curser movement.
I'll continue to test things to see what might be causing problems. One thing I can contribute which showed up after this problem is an Oops during a boot. It could be totally unrelated and it's only happened once (a reboot produced no such Oops), but here it is:
Software Suspend 2.1.5.10: Suspending enabled.
Unable to handle kernel NULL pointer dereference at virtual address 00000004 printing eip: c01266e6 *pde = 00000000 Oops: 0001 [#1] PREEMPT Modules linked in: CPU: 0 EIP: 0060:[<c01226e6>] Not tainted VLI EFLAGS: 00010083 (2.6.10)
EIP is at worker_thread+0x1e6/0x310
eax: 00000000 ebx: cbd0f04c ecx: cbfe77b0 edx: 00000000
esi: cbd0f048 edi: cbfc9000 ebp: 00000283 esp: cbfc9f44
ds: 007b es: 007b ss: 0068
Process events/0 (pid: 3, threadinfo=cbf9000 task=cbfc3020)
Stack: 00000000 cbfc9f74 00000000 cbfe77b8 cbfc9000 cbfc9000 00000000 00000000
cbfc9000 cbfe77a8 ffffffff ffffffff 00000001 00000000 c0112d10 00010000
00000000 00000000 00000000 cbfc9000 00000000 cbfc3020 c0112d10 00100100
Call Trace:
[<c0112d10>] default_wake_function+0x0/0x20
[<c0112d10>] default_wake_function+0x0/0x20
[<c0126500>] worker_thread+0x0/0x310
[<c012ab0a>] kthread+0xba/0xc0
[<c01012e5>] kernel_thread_helper+0x5/0x10
Code: 50 18 89 54 24 0c eb 0d 90 90 90 90 90 90 90 90 90 90 90 90 908d 73 fc 8b 46 0c 89 44 24 1c 8b 56 10 89 54 24 18 8b 53 04
8b 03 <89> 50 04 89 02 89 5b 04 89 1b 55 9d ff 4f 14 8b 47 08 83 e0 08 <6>note: events/0[3] exited with preempt_count 1
Software Suspend 2.1.5.10: This is normal swap space.
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory 160k freed
_
If anything looks odd or unlike normal Oops output, I was unable to capture it digitally and so had to type it out longhand, which could contribute to typos :-/ . Also, since it seems to have occured between the swsusp code loading, I may need to submit it to those guys instead.
HTH. Thanks.
-Andy