display/drm/bridge: TC358775 DSI/LVDS driver
Subsystems (3)
PATCH v4 1/1 display/drm/bridge: TC358775 DSI/LVDS driver
---
v1:
Initial version
v2:
* Andrzej Hajda review comments incorporated SPDX identifier
development debug removed
alphabetic order headers
u32 instead of unit32_t
magic numbers to macros for CLRSI and mux registers ignored return value
* Laurent Pinchart review comments incorporated
mdelay to usleep_range
bus_formats added
v3:
* Andrzej Hajda review comments incorporated drm_connector_status removed
u32 rev removed and local variabl is used regulator enable disable with proper orders and delays as per the spec
devm_drm_panel_bridge_add method used instead of panel description modified
dual port implemented
v4:
* Sam Ravnborg review comments incorporated
panel->connector_type removed
* Reported-by: kernel test robot <[email protected]> parse_dt to static function
removed the if (endpoint), since data-lanes has to be present for dsi dts ports
--- drivers/gpu/drm/bridge/Kconfig | 10 + drivers/gpu/drm/bridge/Makefile | 1 + drivers/gpu/drm/bridge/tc358775.c | 721 ++++++++++++++++++++++++++++++ 3 files changed, 732 insertions(+) create mode 100644 drivers/gpu/drm/bridge/tc358775.c
drivers/gpu/drm/bridge/Kconfig +10 -0
@@ -181,6 +181,16 @@ config DRM_TOSHIBA_TC358768 help Toshiba TC358768AXBG/TC358778XBG DSI bridge chip driver. +config DRM_TOSHIBA_TC358775 + tristate "Toshiba TC358775 LVDS bridge" + depends on OF + select DRM_KMS_HELPER + select REGMAP_I2C + select DRM_PANEL + select DRM_MIPI_DSI + ---help--- + Toshiba TC358775 LVDS bridge chip driver. + config DRM_TI_TFP410 tristate "TI TFP410 DVI/HDMI bridge" depends on OF
drivers/gpu/drm/bridge/Makefile +1 -0
@@ -15,6 +15,7 @@ obj-$(CONFIG_DRM_THINE_THC63LVD1024) += thc63lvd1024.o obj-$(CONFIG_DRM_TOSHIBA_TC358764) += tc358764.o obj-$(CONFIG_DRM_TOSHIBA_TC358767) += tc358767.o obj-$(CONFIG_DRM_TOSHIBA_TC358768) += tc358768.o +obj-$(CONFIG_DRM_TOSHIBA_TC358775) += tc358775.o obj-$(CONFIG_DRM_I2C_ADV7511) += adv7511/ obj-$(CONFIG_DRM_TI_SN65DSI86) += ti-sn65dsi86.o obj-$(CONFIG_DRM_TI_TFP410) += ti-tfp410.o
drivers/gpu/drm/bridge/tc358775.c new file +721 -0
721 lines not on this page · raw message
Signature · 1 line
2.17.1
Hi,
Quoted 29 lines · Vinay Simha BN
Signed-off-by Vinay Simha BN <[email protected]>---
v1:
Initial versionv2:
* Andrzej Hajda review comments incorporated SPDX identifier
development debug removed
alphabetic order headers
u32 instead ofunit32_t
magic numbers to macros for CLRSI and mux registers ignored return value* Laurent Pinchart review comments incorporated
mdelay tousleep_range
bus_formatsaddedv3:
* Andrzej Hajda review comments incorporateddrm_connector_statusremoved
u32 rev removed and local variabl is used regulator enable disable with proper orders and delays as per the spec
devm_drm_panel_bridge_addmethod used instead of panel description modified
dual port implemented
Quoted 8 lines
v4:
* Sam Ravnborg review comments incorporated
panel->connector_typeremoved* Reported-by: kernel test robot <[email protected]>
parse_dtto static function
removed the if (endpoint), since data-lanes has to be present for dsi dts ports
I maybe missed something, but you should also post a YAML DT bindings file associated to the driver.
Neil
Quoted 758 lines
--- drivers/gpu/drm/bridge/Kconfig | 10 + drivers/gpu/drm/bridge/Makefile | 1 + drivers/gpu/drm/bridge/tc358775.c | 721 ++++++++++++++++++++++++++++++ 3 files changed, 732 insertions(+) create mode 100644 drivers/gpu/drm/bridge/tc358775.cdrivers/gpu/drm/bridge/Kconfig +10
-0@@ -181,6 +181,16 @@ config DRM_TOSHIBA_TC358768 help Toshiba TC358768AXBG/TC358778XBG DSI bridge chip driver. +config DRM_TOSHIBA_TC358775 + tristate "Toshiba TC358775 LVDS bridge" + depends on OF + select DRM_KMS_HELPER + select REGMAP_I2C + select DRM_PANEL + select DRM_MIPI_DSI + ---help--- + Toshiba TC358775 LVDS bridge chip driver. + config DRM_TI_TFP410 tristate "TI TFP410 DVI/HDMI bridge" depends on OFdrivers/gpu/drm/bridge/Makefile +1
-0@@ -15,6 +15,7 @@ obj-$(CONFIG_DRM_THINE_THC63LVD1024) += thc63lvd1024.o obj-$(CONFIG_DRM_TOSHIBA_TC358764) += tc358764.o obj-$(CONFIG_DRM_TOSHIBA_TC358767) += tc358767.o obj-$(CONFIG_DRM_TOSHIBA_TC358768) += tc358768.o +obj-$(CONFIG_DRM_TOSHIBA_TC358775) += tc358775.o obj-$(CONFIG_DRM_I2C_ADV7511) += adv7511/ obj-$(CONFIG_DRM_TI_SN65DSI86) += ti-sn65dsi86.o obj-$(CONFIG_DRM_TI_TFP410) += ti-tfp410.odrivers/gpu/drm/bridge/tc358775.c new file +711
-0@@ -0,0 +1,721 @@ +// SPDX-License-Identifier: GPL-2.0 +/* +* tc358775 DSI to LVDS bridge driver +* +* Copyright (C) 2020 SMART Wireless Computing +* Author: Vinay Simha BN <[email protected]> +* +*/ +//#define DEBUG +#include <linux/clk.h> +#include <linux/device.h> +#include <linux/gpio/consumer.h> +#include <linux/i2c.h> +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/regulator/consumer.h> +#include <linux/slab.h> + +#include <drm/drm_atomic_helper.h> +#include <drm/drm_bridge.h> +#include <drm/drm_crtc_helper.h> +#include <drm/drm_dp_helper.h> +#include <drm/drm_mipi_dsi.h> +#include <drm/drm_of.h> +#include <drm/drm_panel.h> +#include <drm/drm_probe_helper.h> + +#define FLD_MASK (start, end) (((1 << ((start) - (end) + 1)) - 1) << (end)) +#define FLD_VAL (val, start, end) (((val) << (end)) & FLD_MASK(start, end)) + +/* Registers */ + +/* DSI D-PHY Layer Registers */ +#define D0W_DPHYCONTTX 0x0004/* Data Lane 0 DPHY Tx Control */ +#define CLW_DPHYCONTRX 0x0020/* Clock Lane DPHY Rx Control */ +#define D0W_DPHYCONTRX 0x0024/* Data Lane 0 DPHY Rx Control */ +#define D1W_DPHYCONTRX 0x0028/* Data Lane 1 DPHY Rx Control */ +#define D2W_DPHYCONTRX 0x002C/* Data Lane 2 DPHY Rx Control */ +#define D3W_DPHYCONTRX 0x0030/* Data Lane 3 DPHY Rx Control */ +#define COM_DPHYCONTRX 0x0038/* DPHY Rx Common Control */ +#define CLW_CNTRL 0x0040/* Clock Lane Control */ +#define D0W_CNTRL 0x0044/* Data Lane 0 Control */ +#define D1W_CNTRL 0x0048/* Data Lane 1 Control */ +#define D2W_CNTRL 0x004C/* Data Lane 2 Control */ +#define D3W_CNTRL 0x0050/* Data Lane 3 Control */ +#define DFTMODE_CNTRL 0x0054/* DFT Mode Control */ + +/* DSI PPI Layer Registers */ +#define PPI_STARTPPI 0x0104/* START control bit of PPI-TX function. */ +#define PPI_START_FUNCTION 1 + +#define PPI_BUSYPPI 0x0108 +#define PPI_LINEINITCNT 0x0110/* Line Initialization Wait Counter */ +#define PPI_LPTXTIMECNT 0x0114 +#define PPI_LANEENABLE 0x0134/* Enables each lane at the PPI layer. */ +#define PPI_TX_RX_TA 0x013C/* DSI Bus Turn Around timing parameters */ + +/* Analog timer function enable */ +#define PPI_CLS_ATMR 0x0140/* Delay for Clock Lane in LPRX */ +#define PPI_D0S_ATMR 0x0144/* Delay for Data Lane 0 in LPRX */ +#define PPI_D1S_ATMR 0x0148/* Delay for Data Lane 1 in LPRX */ +#define PPI_D2S_ATMR 0x014C/* Delay for Data Lane 2 in LPRX */ +#define PPI_D3S_ATMR 0x0150/* Delay for Data Lane 3 in LPRX */ + +#define PPI_D0S_CLRSIPOCOUNT 0x0164/* For lane 0 */ +#define PPI_D1S_CLRSIPOCOUNT 0x0168/* For lane 1 */ +#define PPI_D2S_CLRSIPOCOUNT 0x016C/* For lane 2 */ +#define PPI_D3S_CLRSIPOCOUNT 0x0170/* For lane 3 */ + +#define CLS_PRE 0x0180/* Digital Counter inside of PHY IO */ +#define D0S_PRE 0x0184/* Digital Counter inside of PHY IO */ +#define D1S_PRE 0x0188/* Digital Counter inside of PHY IO */ +#define D2S_PRE 0x018C/* Digital Counter inside of PHY IO */ +#define D3S_PRE 0x0190/* Digital Counter inside of PHY IO */ +#define CLS_PREP 0x01A0/* Digital Counter inside of PHY IO */ +#define D0S_PREP 0x01A4/* Digital Counter inside of PHY IO */ +#define D1S_PREP 0x01A8/* Digital Counter inside of PHY IO */ +#define D2S_PREP 0x01AC/* Digital Counter inside of PHY IO */ +#define D3S_PREP 0x01B0/* Digital Counter inside of PHY IO */ +#define CLS_ZERO 0x01C0/* Digital Counter inside of PHY IO */ +#define D0S_ZERO 0x01C4/* Digital Counter inside of PHY IO */ +#define D1S_ZERO 0x01C8/* Digital Counter inside of PHY IO */ +#define D2S_ZERO 0x01CC/* Digital Counter inside of PHY IO */ +#define D3S_ZERO 0x01D0/* Digital Counter inside of PHY IO */ + +#define PPI_CLRFLG 0x01E0/* PRE Counters has reached set values */ +#define PPI_CLRSIPO 0x01E4/* Clear SIPO values, Slave mode use only. */ +#define HSTIMEOUT 0x01F0/* HS Rx Time Out Counter */ +#define HSTIMEOUTENABLE 0x01F4/* Enable HS Rx Time Out Counter */ +#define DSI_STARTDSI 0x0204/* START control bit of DSI-TX function */ +#define DSI_RX_START 1 + +#define DSI_BUSYDSI 0x0208 +#define DSI_LANEENABLE 0x0210/* Enables each lane at the Protocol layer. */ +#define DSI_LANESTATUS0 0x0214/* Displays lane is in HS RX mode. */ +#define DSI_LANESTATUS1 0x0218/* Displays lane is in ULPS or STOP state */ + +#define DSI_INTSTATUS 0x0220/* Interrupt Status */ +#define DSI_INTMASK 0x0224/* Interrupt Mask */ +#define DSI_INTCLR 0x0228/* Interrupt Clear */ +#define DSI_LPTXTO 0x0230/* Low Power Tx Time Out Counter */ + +#define DSIERRCNT 0x0300/* DSI Error Count */ +#define APLCTRL 0x0400/* Application Layer Control */ +#define RDPKTLN 0x0404/* Command Read Packet Length */ + +#define VPCTRL 0x0450/* Video Path Control */ +#define HTIM1 0x0454/* Horizontal Timing Control 1 */ +#define HTIM2 0x0458/* Horizontal Timing Control 2 */ +#define VTIM1 0x045C/* Vertical Timing Control 1 */ +#define VTIM2 0x0460/* Vertical Timing Control 2 */ +#define VFUEN 0x0464/* Video Frame Timing Update Enable */ +#define VFUEN_EN BIT(0)/* Upload Enable */ + +/* Mux Input Select for LVDS LINK Input */ +#define LV_MX0003 0x0480/* Bit 0 to 3 */ +#define LV_MX0407 0x0484/* Bit 4 to 7 */ +#define LV_MX0811 0x0488/* Bit 8 to 11 */ +#define LV_MX1215 0x048C/* Bit 12 to 15 */ +#define LV_MX1619 0x0490/* Bit 16 to 19 */ +#define LV_MX2023 0x0494/* Bit 20 to 23 */ +#define LV_MX2427 0x0498/* Bit 24 to 27 */ +#define LV_MX (b0, b1, b2, b3) (FLD_VAL(b0, 4, 0) | FLD_VAL(b1, 12, 8) | \ + FLD_VAL(b2, 20, 16) | FLD_VAL(b3, 28, 24)) + +/* Input bit numbers used in mux registers */ +enum { +LVI_R0 , +LVI_R1 , +LVI_R2 , +LVI_R3 , +LVI_R4 , +LVI_R5 , +LVI_R6 , +LVI_R7 , +LVI_G0 , +LVI_G1 , +LVI_G2 , +LVI_G3 , +LVI_G4 , +LVI_G5 , +LVI_G6 , +LVI_G7 , +LVI_B0 , +LVI_B1 , +LVI_B2 , +LVI_B3 , +LVI_B4 , +LVI_B5 , +LVI_B6 , +LVI_B7 , +LVI_HS , +LVI_VS , +LVI_DE , +LVI_L0 +}; + +#define LVCFG 0x049C/* LVDS Configuration */ +#define LVPHY0 0x04A0/* LVDS PHY 0 */ +#define LV_PHY0_RST (v) FLD_VAL(v, 22, 22)/* PHY reset */ +#define LV_PHY0_IS (v) FLD_VAL(v, 15, 14) +#define LV_PHY0_ND (v) FLD_VAL(v, 4, 0)/* Frequency range select */ +#define LV_PHY0_PRBS_ON (v) FLD_VAL(v, 20, 16)/* Clock/Data Flag pins */ + +#define LVPHY1 0x04A4/* LVDS PHY 1 */ +#define SYSSTAT 0x0500/* System Status */ +#define SYSRST 0x0504/* System Reset */ + +#define SYS_RST_I2CS BIT(0)/* Reset I2C-Slave controller */ +#define SYS_RST_I2CM BIT(1)/* Reset I2C-Master controller */ +#define SYS_RST_LCD BIT(2)/* Reset LCD controller */ +#define SYS_RST_BM BIT(3)/* Reset Bus Management controller */ +#define SYS_RST_DSIRX BIT(4)/* Reset DSI-RX and App controller */ +#define SYS_RST_REG BIT(5)/* Reset Register module */ + +/* GPIO Registers */ +#define GPIOC 0x0520/* GPIO Control */ +#define GPIOO 0x0524/* GPIO Output */ +#define GPIOI 0x0528/* GPIO Input */ + +/* I2C Registers */ +#define I2CTIMCTRL 0x0540/* I2C IF Timing and Enable Control */ +#define I2CMADDR 0x0544/* I2C Master Addressing */ +#define WDATAQ 0x0548/* Write Data Queue */ +#define RDATAQ 0x054C/* Read Data Queue */ + +/* Chip ID and Revision ID Register */ +#define IDREG 0x0580 + +#define LPX_PERIOD 4 +#define TTA_GET 0x40000 +#define TTA_SURE 6 + +#define TC358775XBG_ID 0x00007500 + +/* Debug Registers */ +#define DEBUG00 0x05A0/* Debug */ +#define DEBUG01 0x05A4/* LVDS Data */ + +#define DSI_CLEN_BIT BIT(0) +#define DIVIDE_BY_3 3/* PCLK=DCLK/3 */ +#define DIVIDE_BY_6 6/* PCLK=DCLK/6 */ +#define LVCFG_LVEN_BIT BIT(0) + +#define L0EN BIT(1) + +#define TC358775_VPCTRL_VSDELAY__MASK 0x3FF00000 +#define TC358775_VPCTRL_VSDELAY__SHIFT 20 +static inline u32 TC358775_VPCTRL_VSDELAY (uint32_t val) +{ +return ((val) <<TC358775_VPCTRL_VSDELAY__SHIFT ) & +TC358775_VPCTRL_VSDELAY__MASK ; +} + +#define TC358775_VPCTRL_OPXLFMT__MASK 0x00000100 +#define TC358775_VPCTRL_OPXLFMT__SHIFT 8 +static inline u32 TC358775_VPCTRL_OPXLFMT (uint32_t val) +{ +return ((val) <<TC358775_VPCTRL_OPXLFMT__SHIFT ) & +TC358775_VPCTRL_OPXLFMT__MASK ; +} + +#define TC358775_VPCTRL_MSF__MASK 0x00000001 +#define TC358775_VPCTRL_MSF__SHIFT 0 +static inline u32 TC358775_VPCTRL_MSF (uint32_t val) +{ +return ((val) <<TC358775_VPCTRL_MSF__SHIFT ) & +TC358775_VPCTRL_MSF__MASK ; +} + +#define TC358775_LVCFG_PCLKDIV__MASK 0x000000f0 +#define TC358775_LVCFG_PCLKDIV__SHIFT 4 +static inline u32 TC358775_LVCFG_PCLKDIV (uint32_t val) +{ +return ((val) <<TC358775_LVCFG_PCLKDIV__SHIFT ) & +TC358775_LVCFG_PCLKDIV__MASK ; +} + +#define TC358775_LVCFG_LVDLINK__MASK 0x00000002 +#define TC358775_LVCFG_LVDLINK__SHIFT 0 +static inline u32 TC358775_LVCFG_LVDLINK (uint32_t val) +{ +return ((val) <<TC358775_LVCFG_LVDLINK__SHIFT ) & +TC358775_LVCFG_LVDLINK__MASK ; +} + +enum tc358775_ports { +TC358775_DSI_IN , +TC358775_LVDS_OUT0 , +TC358775_LVDS_OUT1 , +}; + +struct tc_data { +struct i2c_client *i2c; +struct device *dev; + +struct drm_bridge bridge; +struct drm_bridge *panel_bridge; + +struct device_node *host_node; +struct mipi_dsi_device *dsi; +u8 num_dsi_lanes; + +struct regulator *vdd; +struct regulator *vddio; +struct gpio_desc *reset_gpio; +struct gpio_desc *stby_gpio; +bool dual_link;/* single-link or dual-link */ +}; + +static inline struct tc_data *bridge_to_tc (struct drm_bridge *b) +{ + return container_of(b, struct tc_data, bridge); +} + +static void tc_bridge_pre_enable (struct drm_bridge *bridge) +{ +struct tc_data *tc =bridge_to_tc (bridge); +struct device *dev = &tc->dsi->dev; +int ret; + + ret =regulator_enable (tc->vddio); +if (ret <0 ) +dev_err (dev,"regulator vddio enable failed, %d\n" , ret); +usleep_range (10000 ,11000 ); + + ret =regulator_enable (tc->vdd); +if (ret <0 ) +dev_err (dev,"regulator vdd enable failed, %d\n" , ret); +usleep_range (10000 ,11000 ); + +gpiod_set_value (tc->stby_gpio,0 ); +usleep_range (10000 ,11000 ); + +gpiod_set_value (tc->reset_gpio,0 ); +usleep_range (10 ,20 ); +} + +static void tc_bridge_post_disable (struct drm_bridge *bridge) +{ +struct tc_data *tc =bridge_to_tc (bridge); +struct device *dev = &tc->dsi->dev; +int ret; + + ret =regulator_disable (tc->vddio); +if (ret <0 ) +dev_err (dev,"regulator vddio disable failed, %d\n" , ret); +usleep_range (10000 ,11000 ); + + ret =regulator_disable (tc->vdd); +if (ret <0 ) +dev_err (dev,"regulator vdd disable failed, %d\n" , ret); +usleep_range (10000 ,11000 ); + +gpiod_set_value (tc->stby_gpio,1 ); +usleep_range (10000 ,11000 ); + +gpiod_set_value (tc->reset_gpio,1 ); +usleep_range (10 ,20 ); +} + +static u32 d2l_read (struct i2c_client *i2c,u16 reg) +{ +int ret; +u8 val[4 ]; +u8 addr[] = {(reg >>8 ) &0xff , reg &0xff }; +u32 value; + + ret =i2c_master_send (i2c, addr,sizeof (reg)); +if (ret <0 ) + goto fail; + + ret =i2c_master_recv (i2c, val,sizeof (value)); +if (ret <0 ) + goto fail; + + value = val[3 ] <<24 | val[2 ] <<16 | val[1 ] <<8 | val[0 ]; + +pr_debug ("d2l: I2C : reg:%04x value:%08x\n" , reg, value); + +return value; + +fail: +dev_err (&i2c->dev,"Error %d reading from subaddress 0x%x\n" , + ret, reg); +return 0 ; +} + +static void d2l_write (struct i2c_client *i2c,u16 reg,u32 val) +{ +u8 buf[6 ]; +int ret; + + buf[0 ] = reg >>8 ; + buf[1 ] = reg &0xFF ; + buf[2 ] = (val >>0 ) &0xFF ; + buf[3 ] = (val >>8 ) &0xFF ; + buf[4 ] = (val >>16 ) &0xFF ; + buf[5 ] = (val >>24 ) &0xFF ; + + ret =i2c_master_send (i2c, buf,ARRAY_SIZE (buf)); +if (ret <0 ) +dev_err (&i2c->dev,"Error %d writing to subaddress 0x%x\n" , + ret, reg); +} + +/* helper function to access bus_formats */ +static struct drm_connector *get_connector (struct drm_encoder *encoder) +{ +struct drm_device *dev = encoder->dev; +struct drm_connector *connector; + +list_for_each_entry (connector, &dev->mode_config.connector_list, head) +if (connector->encoder == encoder) +return connector; + +return NULL ; +} + +static void tc_bridge_enable (struct drm_bridge *bridge) +{ +struct tc_data *tc =bridge_to_tc (bridge); +u32 hbpr, hpw, htime1, hfpr, hsize, htime2; +u32 vbpr, vpw, vtime1, vfpr, vsize, vtime2; +u32 val =0 ; +u16 bus_formats; +struct drm_display_mode *mode; +struct drm_connector *connector =get_connector (bridge->encoder); + + mode = &bridge->encoder->crtc->state->adjusted_mode; + + hbpr = mode->htotal - mode->hsync_end; + hpw = mode->hsync_end - mode->hsync_start; + vbpr = mode->vtotal - mode->vsync_end; + vpw = mode->vsync_end - mode->vsync_start; + + htime1 = (hbpr <<16 ) + hpw; + vtime1 = (vbpr <<16 ) + vpw; + + hfpr = mode->hsync_start - mode->hdisplay; + hsize = mode->hdisplay; + vfpr = mode->vsync_start - mode->vdisplay; + vsize = mode->vdisplay; + + htime2 = (hfpr <<16 ) + hsize; + vtime2 = (vfpr <<16 ) + vsize; + + val =d2l_read (tc->i2c,IDREG ); + +dev_info (tc->dev,"DSI2LVDS Chip ID.%02x Revision ID. %02x **\n" , + (val >>8 ) &0xFF , val &0xFF ); + +d2l_write (tc->i2c,SYSRST ,SYS_RST_REG |SYS_RST_DSIRX |SYS_RST_BM | +SYS_RST_LCD |SYS_RST_I2CM |SYS_RST_I2CS ); +usleep_range (30000 ,40000 ); + +d2l_write (tc->i2c,PPI_TX_RX_TA ,TTA_GET |TTA_SURE ); +d2l_write (tc->i2c,PPI_LPTXTIMECNT ,LPX_PERIOD ); +d2l_write (tc->i2c,PPI_D0S_CLRSIPOCOUNT ,3 ); +d2l_write (tc->i2c,PPI_D1S_CLRSIPOCOUNT ,3 ); +d2l_write (tc->i2c,PPI_D2S_CLRSIPOCOUNT ,3 ); +d2l_write (tc->i2c,PPI_D3S_CLRSIPOCOUNT ,3 ); + + val = ((L0EN << tc->num_dsi_lanes) -L0EN ) |DSI_CLEN_BIT ; +d2l_write (tc->i2c,PPI_LANEENABLE , val); +d2l_write (tc->i2c,DSI_LANEENABLE , val); + +d2l_write (tc->i2c,PPI_STARTPPI ,PPI_START_FUNCTION ); +d2l_write (tc->i2c,DSI_STARTDSI ,DSI_RX_START ); + + val =TC358775_VPCTRL_VSDELAY (21 ); + + bus_formats = connector->display_info.bus_formats[0 ]; +dev_dbg (tc->dev,"bus_formats : %04x\n" , bus_formats); + +if (bus_formats ==MEDIA_BUS_FMT_RGB888_1X7X4_SPWG || + bus_formats ==MEDIA_BUS_FMT_RGB888_1X7X4_JEIDA ) { +/* RGB888 */ + val |=TC358775_VPCTRL_OPXLFMT (1 ); +d2l_write (tc->i2c,VPCTRL , val); + }else { +/* RGB666 */ + val |=TC358775_VPCTRL_MSF (1 ); +d2l_write (tc->i2c,VPCTRL , val); + } + +d2l_write (tc->i2c,HTIM1 , htime1); +d2l_write (tc->i2c,VTIM1 , vtime1); +d2l_write (tc->i2c,HTIM2 , htime2); +d2l_write (tc->i2c,VTIM2 , vtime2); + +d2l_write (tc->i2c,VFUEN ,VFUEN_EN ); +d2l_write (tc->i2c,SYSRST ,SYS_RST_LCD ); +d2l_write (tc->i2c,LVPHY0 ,LV_PHY0_PRBS_ON (4 ) |LV_PHY0_ND (6 )); + +/* default jeida-24 */ +if (bus_formats ==MEDIA_BUS_FMT_RGB888_1X7X4_SPWG ) { +/* vesa-24 */ +d2l_write (tc->i2c,LV_MX0003 ,LV_MX (LVI_R0 ,LVI_R1 ,LVI_R2 ,LVI_R3 )); +d2l_write (tc->i2c,LV_MX0407 ,LV_MX (LVI_R4 ,LVI_R7 ,LVI_R5 ,LVI_G0 )); +d2l_write (tc->i2c,LV_MX0811 ,LV_MX (LVI_G1 ,LVI_G2 ,LVI_G6 ,LVI_G7 )); +d2l_write (tc->i2c,LV_MX1215 ,LV_MX (LVI_G3 ,LVI_G4 ,LVI_G5 ,LVI_B0 )); +d2l_write (tc->i2c,LV_MX1619 ,LV_MX (LVI_B6 ,LVI_B7 ,LVI_B1 ,LVI_B2 )); +d2l_write (tc->i2c,LV_MX2023 ,LV_MX (LVI_B3 ,LVI_B4 ,LVI_B5 ,LVI_L0 )); +d2l_write (tc->i2c,LV_MX2427 ,LV_MX (LVI_HS ,LVI_VS ,LVI_DE ,LVI_R6 )); + } + +if (bus_formats ==MEDIA_BUS_FMT_RGB666_1X7X3_SPWG ) { +/* jeida-18 */ +d2l_write (tc->i2c,LV_MX0003 ,LV_MX (LVI_R0 ,LVI_R1 ,LVI_R2 ,LVI_R3 )); +d2l_write (tc->i2c,LV_MX0407 ,LV_MX (LVI_R4 ,LVI_L0 ,LVI_R5 ,LVI_G0 )); +d2l_write (tc->i2c,LV_MX0811 ,LV_MX (LVI_G1 ,LVI_G2 ,LVI_L0 ,LVI_L0 )); +d2l_write (tc->i2c,LV_MX1215 ,LV_MX (LVI_G3 ,LVI_G4 ,LVI_G5 ,LVI_B0 )); +d2l_write (tc->i2c,LV_MX1619 ,LV_MX (LVI_L0 ,LVI_L0 ,LVI_B1 ,LVI_B2 )); +d2l_write (tc->i2c,LV_MX2023 ,LV_MX (LVI_B3 ,LVI_B4 ,LVI_B5 ,LVI_L0 )); +d2l_write (tc->i2c,LV_MX2427 ,LV_MX (LVI_HS ,LVI_VS ,LVI_DE ,LVI_L0 )); + } + +d2l_write (tc->i2c,VFUEN ,VFUEN_EN ); + + val =LVCFG_LVEN_BIT ; +if (tc->dual_link) { + val |=TC358775_LVCFG_LVDLINK (1 ); + val |=TC358775_LVCFG_PCLKDIV (DIVIDE_BY_6 ); + }else { + val |=TC358775_LVCFG_PCLKDIV (DIVIDE_BY_3 ); + } + +d2l_write (tc->i2c,LVCFG , val); +} + +static int tc_mode_valid (struct drm_bridge *bridge, +const struct drm_display_mode *mode) +{ +struct tc_data *tc =bridge_to_tc (bridge); + +/* Maximum pixel clock speed 135MHz-single-link/270MHz-dual-link */ +if ((mode->clock >135000 && tc->dual_link) || + (mode->clock >270000 && tc->dual_link)) +return MODE_CLOCK_HIGH ; + +return MODE_OK ; +} + +static int tc358775_parse_dt (struct device_node *np,struct tc_data *tc) +{ +struct device_node *endpoint; +struct device_node *parent; +struct device_node *remote; +struct property *prop; +int len; + + endpoint =of_graph_get_endpoint_by_regs (tc->dev->of_node, +TC358775_DSI_IN ,-1 ); +if (endpoint) { +/* dsi0_out node */ + parent =of_graph_get_remote_port_parent (endpoint); +of_node_put (endpoint); +if (parent) { +/* dsi0 port 1 */ + endpoint =of_graph_get_endpoint_by_regs (parent,1 ,-1 ); +of_node_put (parent); + prop =of_find_property (endpoint,"data-lanes" , + &len); +of_node_put (endpoint); +if (!prop) { +dev_err (tc->dev, +"failed to find data lane\n" ); +return -EPROBE_DEFER ; + } + } + } + + tc->num_dsi_lanes = len /sizeof (u32); + +if (tc->num_dsi_lanes <1 || tc->num_dsi_lanes >4 ) +return -EINVAL ; + + tc->host_node =of_graph_get_remote_node (np,0 ,0 ); +if (!tc->host_node) +return -ENODEV ; + +of_node_put (tc->host_node); + + endpoint =of_graph_get_endpoint_by_regs (tc->dev->of_node, +TC358775_LVDS_OUT1 ,-1 ); +if (endpoint) { + remote =of_graph_get_remote_port_parent (endpoint); +of_node_put (endpoint); + +if (remote) { +if (of_device_is_available (remote)) + tc->dual_link = true; +of_node_put (remote); + } + } + +dev_dbg (tc->dev,"no.of dsi lanes: %d\n" , tc->num_dsi_lanes); +dev_dbg (tc->dev,"operating in %s-link mode\n" , + tc->dual_link ?"dual" :"single" ); + +return 0 ; +} + +static int tc_bridge_attach (struct drm_bridge *bridge, +enum drm_bridge_attach_flags flags) +{ +struct tc_data *tc =bridge_to_tc (bridge); +struct device *dev = &tc->i2c->dev; +struct mipi_dsi_host *host; +struct mipi_dsi_device *dsi; +int ret; + +const struct mipi_dsi_device_info info = { .type ="tc358775" , + .channel =0 , + .node =NULL , + }; + + host =of_find_mipi_dsi_host_by_node (tc->host_node); +if (!host) { +dev_err (dev,"failed to find dsi host\n" ); +return -EPROBE_DEFER ; + } + + dsi =mipi_dsi_device_register_full (host, &info); +if (IS_ERR (dsi)) { +dev_err (dev,"failed to create dsi device\n" ); + ret =PTR_ERR (dsi); + goto err_dsi_device; + } + + tc->dsi = dsi; + + dsi->lanes = tc->num_dsi_lanes; + dsi->format =MIPI_DSI_FMT_RGB888 ; + dsi->mode_flags =MIPI_DSI_MODE_VIDEO ; + + ret =mipi_dsi_attach (dsi); +if (ret <0 ) { +dev_err (dev,"failed to attach dsi to host\n" ); + goto err_dsi_attach; + } + +/* Attach the panel-bridge to the dsi bridge */ +return drm_bridge_attach (bridge->encoder, tc->panel_bridge, + &tc->bridge, flags); +err_dsi_attach: +mipi_dsi_device_unregister (dsi); +err_dsi_device: +return ret; +} + +static const struct drm_bridge_funcs tc_bridge_funcs = { + .attach = tc_bridge_attach, + .pre_enable = tc_bridge_pre_enable, + .enable = tc_bridge_enable, + .mode_valid = tc_mode_valid, + .post_disable = tc_bridge_post_disable, +}; + +static int tc_probe (struct i2c_client *client,const struct i2c_device_id *id) +{ +struct device *dev = &client->dev; +struct drm_panel *panel; +struct tc_data *tc; +int ret; + + tc =devm_kzalloc (dev,sizeof (*tc),GFP_KERNEL ); +if (!tc) +return -ENOMEM ; + + tc->dev = dev; + tc->i2c = client; + + ret =drm_of_find_panel_or_bridge (dev->of_node,TC358775_LVDS_OUT0 , +0 , &panel,NULL ); +if (ret <0 ) +return ret; +if (!panel) +return -ENODEV ; + + tc->panel_bridge =devm_drm_panel_bridge_add (dev, panel); +if (IS_ERR (tc->panel_bridge)) +return PTR_ERR (tc->panel_bridge); + + ret =tc358775_parse_dt (dev->of_node, tc); +if (ret) +return ret; + + tc->vddio =devm_regulator_get (dev,"vddio-supply" ); +if (IS_ERR (tc->vddio)) { + ret =PTR_ERR (tc->vddio); +dev_err (dev,"vddio-supply not found\n" ); +return ret; + } + + tc->vdd =devm_regulator_get (dev,"vdd-supply" ); +if (IS_ERR (tc->vdd)) { + ret =PTR_ERR (tc->vddio); +dev_err (dev,"vdd-supply not found\n" ); +return ret; + } + + tc->stby_gpio =devm_gpiod_get (dev,"stby" ,GPIOD_OUT_HIGH ); +if (IS_ERR (tc->stby_gpio)) { + ret =PTR_ERR (tc->stby_gpio); +dev_err (dev,"cannot get stby-gpio %d\n" , ret); +return ret; + } + + tc->reset_gpio =devm_gpiod_get (dev,"reset" ,GPIOD_OUT_HIGH ); +if (IS_ERR (tc->reset_gpio)) { + ret =PTR_ERR (tc->reset_gpio); +dev_err (dev,"cannot get reset-gpios %d\n" , ret); +return ret; + } + + tc->bridge.funcs = &tc_bridge_funcs; + tc->bridge.of_node = dev->of_node; +drm_bridge_add (&tc->bridge); + +i2c_set_clientdata (client, tc); + +return 0 ; +} + +static int tc_remove (struct i2c_client *client) +{ +struct tc_data *tc =i2c_get_clientdata (client); + +drm_bridge_remove (&tc->bridge); + +return 0 ; +} + +static const struct i2c_device_id tc358775_i2c_ids[] = { + {"tc358775" ,0 }, + { } +}; +MODULE_DEVICE_TABLE (i2c, tc358775_i2c_ids); + +static const struct of_device_id tc358775_of_ids[] = { + { .compatible ="toshiba,tc358775" , }, + { } +}; +MODULE_DEVICE_TABLE (of, tc358775_of_ids); + +static struct i2c_driver tc358775_driver = { + .driver = { + .name ="tc358775" , + .of_match_table = tc358775_of_ids,
drivers/gpu/drm/bridge/tc358775.c line 721
Quoted 10 lines
drivers/gpu/drm/bridge/tc358775.c new file +10
-0+ }, + .id_table = tc358775_i2c_ids, + .probe = tc_probe, + .remove = tc_remove, +}; +module_i2c_driver (tc358775_driver); + +MODULE_AUTHOR ("Vinay Simha BN <[email protected]>" ); +MODULE_DESCRIPTION ("TC358775 DSI/LVDS bridge driver" ); +MODULE_LICENSE ("GPL v2" );
_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
Neil,
yaml is the v3 version, there was no change , so i had not created v4 for yaml [PATCH v3 2/2] display/drm/bridge: TC358775 DSI/LVDS driver
Quoted 817 lines · Neil Armstrong
Hi,
Quoted 29 lines · Vinay Simha BN
Signed-off-by Vinay Simha BN <[email protected]>---
v1:
Initial versionv2:
* Andrzej Hajda review comments incorporated SPDX identifier
development debug removed
alphabetic order headers
u32 instead ofunit32_t
magic numbers to macros for CLRSI and mux registers ignored return value* Laurent Pinchart review comments incorporated
mdelay tousleep_range
bus_formatsaddedv3:
* Andrzej Hajda review comments incorporateddrm_connector_statusremoved
u32 rev removed and local variabl is used regulator enable disable with proper orders and delays as per the spec
devm_drm_panel_bridge_addmethod used instead of panel description modified
dual port implementedQuoted 8 lines
v4:
* Sam Ravnborg review comments incorporated
panel->connector_typeremoved* Reported-by: kernel test robot <[email protected]>
parse_dtto static function
removed the if (endpoint), since data-lanes has to be present for dsi dts portsI maybe missed something, but you should also post a YAML DT bindings file associated to the driver.
Neil
Quoted 768 lines
--- drivers/gpu/drm/bridge/Kconfig | 10 + drivers/gpu/drm/bridge/Makefile | 1 + drivers/gpu/drm/bridge/tc358775.c | 721 ++++++++++++++++++++++++++++++ 3 files changed, 732 insertions(+) create mode 100644 drivers/gpu/drm/bridge/tc358775.cdrivers/gpu/drm/bridge/Kconfig +10
-0@@ -181,6 +181,16 @@ config DRM_TOSHIBA_TC358768 help Toshiba TC358768AXBG/TC358778XBG DSI bridge chip driver. +config DRM_TOSHIBA_TC358775 + tristate "Toshiba TC358775 LVDS bridge" + depends on OF + select DRM_KMS_HELPER + select REGMAP_I2C + select DRM_PANEL + select DRM_MIPI_DSI + ---help--- + Toshiba TC358775 LVDS bridge chip driver. + config DRM_TI_TFP410 tristate "TI TFP410 DVI/HDMI bridge" depends on OFdrivers/gpu/drm/bridge/Makefile +1
-0@@ -15,6 +15,7 @@ obj-$(CONFIG_DRM_THINE_THC63LVD1024) += thc63lvd1024.o obj-$(CONFIG_DRM_TOSHIBA_TC358764) += tc358764.o obj-$(CONFIG_DRM_TOSHIBA_TC358767) += tc358767.o obj-$(CONFIG_DRM_TOSHIBA_TC358768) += tc358768.o +obj-$(CONFIG_DRM_TOSHIBA_TC358775) += tc358775.o obj-$(CONFIG_DRM_I2C_ADV7511) += adv7511/ obj-$(CONFIG_DRM_TI_SN65DSI86) += ti-sn65dsi86.o obj-$(CONFIG_DRM_TI_TFP410) += ti-tfp410.odrivers/gpu/drm/bridge/tc358775.c new file +721
-0@@ -0,0 +1,721 @@ +// SPDX-License-Identifier: GPL-2.0 +/* +* tc358775 DSI to LVDS bridge driver +* +* Copyright (C) 2020 SMART Wireless Computing +* Author: Vinay Simha BN <[email protected]> +* +*/ +//#define DEBUG +#include <linux/clk.h> +#include <linux/device.h> +#include <linux/gpio/consumer.h> +#include <linux/i2c.h> +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/regulator/consumer.h> +#include <linux/slab.h> + +#include <drm/drm_atomic_helper.h> +#include <drm/drm_bridge.h> +#include <drm/drm_crtc_helper.h> +#include <drm/drm_dp_helper.h> +#include <drm/drm_mipi_dsi.h> +#include <drm/drm_of.h> +#include <drm/drm_panel.h> +#include <drm/drm_probe_helper.h> + +#define FLD_MASK (start, end) (((1 << ((start) - (end) + 1)) - 1) << (end)) +#define FLD_VAL (val, start, end) (((val) << (end)) & FLD_MASK(start, end)) + +/* Registers */ + +/* DSI D-PHY Layer Registers */ +#define D0W_DPHYCONTTX 0x0004/* Data Lane 0 DPHY Tx Control */ +#define CLW_DPHYCONTRX 0x0020/* Clock Lane DPHY Rx Control */ +#define D0W_DPHYCONTRX 0x0024/* Data Lane 0 DPHY Rx Control */ +#define D1W_DPHYCONTRX 0x0028/* Data Lane 1 DPHY Rx Control */ +#define D2W_DPHYCONTRX 0x002C/* Data Lane 2 DPHY Rx Control */ +#define D3W_DPHYCONTRX 0x0030/* Data Lane 3 DPHY Rx Control */ +#define COM_DPHYCONTRX 0x0038/* DPHY Rx Common Control */ +#define CLW_CNTRL 0x0040/* Clock Lane Control */ +#define D0W_CNTRL 0x0044/* Data Lane 0 Control */ +#define D1W_CNTRL 0x0048/* Data Lane 1 Control */ +#define D2W_CNTRL 0x004C/* Data Lane 2 Control */ +#define D3W_CNTRL 0x0050/* Data Lane 3 Control */ +#define DFTMODE_CNTRL 0x0054/* DFT Mode Control */ + +/* DSI PPI Layer Registers */ +#define PPI_STARTPPI 0x0104/* START control bit of PPI-TX function. */ +#define PPI_START_FUNCTION 1 + +#define PPI_BUSYPPI 0x0108 +#define PPI_LINEINITCNT 0x0110/* Line Initialization Wait Counter */ +#define PPI_LPTXTIMECNT 0x0114 +#define PPI_LANEENABLE 0x0134/* Enables each lane at the PPI layer. */ +#define PPI_TX_RX_TA 0x013C/* DSI Bus Turn Around timing parameters */ + +/* Analog timer function enable */ +#define PPI_CLS_ATMR 0x0140/* Delay for Clock Lane in LPRX */ +#define PPI_D0S_ATMR 0x0144/* Delay for Data Lane 0 in LPRX */ +#define PPI_D1S_ATMR 0x0148/* Delay for Data Lane 1 in LPRX */ +#define PPI_D2S_ATMR 0x014C/* Delay for Data Lane 2 in LPRX */ +#define PPI_D3S_ATMR 0x0150/* Delay for Data Lane 3 in LPRX */ + +#define PPI_D0S_CLRSIPOCOUNT 0x0164/* For lane 0 */ +#define PPI_D1S_CLRSIPOCOUNT 0x0168/* For lane 1 */ +#define PPI_D2S_CLRSIPOCOUNT 0x016C/* For lane 2 */ +#define PPI_D3S_CLRSIPOCOUNT 0x0170/* For lane 3 */ + +#define CLS_PRE 0x0180/* Digital Counter inside of PHY IO */ +#define D0S_PRE 0x0184/* Digital Counter inside of PHY IO */ +#define D1S_PRE 0x0188/* Digital Counter inside of PHY IO */ +#define D2S_PRE 0x018C/* Digital Counter inside of PHY IO */ +#define D3S_PRE 0x0190/* Digital Counter inside of PHY IO */ +#define CLS_PREP 0x01A0/* Digital Counter inside of PHY IO */ +#define D0S_PREP 0x01A4/* Digital Counter inside of PHY IO */ +#define D1S_PREP 0x01A8/* Digital Counter inside of PHY IO */ +#define D2S_PREP 0x01AC/* Digital Counter inside of PHY IO */ +#define D3S_PREP 0x01B0/* Digital Counter inside of PHY IO */ +#define CLS_ZERO 0x01C0/* Digital Counter inside of PHY IO */ +#define D0S_ZERO 0x01C4/* Digital Counter inside of PHY IO */ +#define D1S_ZERO 0x01C8/* Digital Counter inside of PHY IO */ +#define D2S_ZERO 0x01CC/* Digital Counter inside of PHY IO */ +#define D3S_ZERO 0x01D0/* Digital Counter inside of PHY IO */ + +#define PPI_CLRFLG 0x01E0/* PRE Counters has reached set values */ +#define PPI_CLRSIPO 0x01E4/* Clear SIPO values, Slave mode use only. */ +#define HSTIMEOUT 0x01F0/* HS Rx Time Out Counter */ +#define HSTIMEOUTENABLE 0x01F4/* Enable HS Rx Time Out Counter */ +#define DSI_STARTDSI 0x0204/* START control bit of DSI-TX function */ +#define DSI_RX_START 1 + +#define DSI_BUSYDSI 0x0208 +#define DSI_LANEENABLE 0x0210/* Enables each lane at the Protocol layer. */ +#define DSI_LANESTATUS0 0x0214/* Displays lane is in HS RX mode. */ +#define DSI_LANESTATUS1 0x0218/* Displays lane is in ULPS or STOP state */ + +#define DSI_INTSTATUS 0x0220/* Interrupt Status */ +#define DSI_INTMASK 0x0224/* Interrupt Mask */ +#define DSI_INTCLR 0x0228/* Interrupt Clear */ +#define DSI_LPTXTO 0x0230/* Low Power Tx Time Out Counter */ + +#define DSIERRCNT 0x0300/* DSI Error Count */ +#define APLCTRL 0x0400/* Application Layer Control */ +#define RDPKTLN 0x0404/* Command Read Packet Length */ + +#define VPCTRL 0x0450/* Video Path Control */ +#define HTIM1 0x0454/* Horizontal Timing Control 1 */ +#define HTIM2 0x0458/* Horizontal Timing Control 2 */ +#define VTIM1 0x045C/* Vertical Timing Control 1 */ +#define VTIM2 0x0460/* Vertical Timing Control 2 */ +#define VFUEN 0x0464/* Video Frame Timing Update Enable */ +#define VFUEN_EN BIT(0)/* Upload Enable */ + +/* Mux Input Select for LVDS LINK Input */ +#define LV_MX0003 0x0480/* Bit 0 to 3 */ +#define LV_MX0407 0x0484/* Bit 4 to 7 */ +#define LV_MX0811 0x0488/* Bit 8 to 11 */ +#define LV_MX1215 0x048C/* Bit 12 to 15 */ +#define LV_MX1619 0x0490/* Bit 16 to 19 */ +#define LV_MX2023 0x0494/* Bit 20 to 23 */ +#define LV_MX2427 0x0498/* Bit 24 to 27 */ +#define LV_MX (b0, b1, b2, b3) (FLD_VAL(b0, 4, 0) | FLD_VAL(b1, 12, 8) | \ + FLD_VAL(b2, 20, 16) | FLD_VAL(b3, 28, 24)) + +/* Input bit numbers used in mux registers */ +enum { +LVI_R0 , +LVI_R1 , +LVI_R2 , +LVI_R3 , +LVI_R4 , +LVI_R5 , +LVI_R6 , +LVI_R7 , +LVI_G0 , +LVI_G1 , +LVI_G2 , +LVI_G3 , +LVI_G4 , +LVI_G5 , +LVI_G6 , +LVI_G7 , +LVI_B0 , +LVI_B1 , +LVI_B2 , +LVI_B3 , +LVI_B4 , +LVI_B5 , +LVI_B6 , +LVI_B7 , +LVI_HS , +LVI_VS , +LVI_DE , +LVI_L0 +}; + +#define LVCFG 0x049C/* LVDS Configuration */ +#define LVPHY0 0x04A0/* LVDS PHY 0 */ +#define LV_PHY0_RST (v) FLD_VAL(v, 22, 22)/* PHY reset */ +#define LV_PHY0_IS (v) FLD_VAL(v, 15, 14) +#define LV_PHY0_ND (v) FLD_VAL(v, 4, 0)/* Frequency range select */ +#define LV_PHY0_PRBS_ON (v) FLD_VAL(v, 20, 16)/* Clock/Data Flag pins */ + +#define LVPHY1 0x04A4/* LVDS PHY 1 */ +#define SYSSTAT 0x0500/* System Status */ +#define SYSRST 0x0504/* System Reset */ + +#define SYS_RST_I2CS BIT(0)/* Reset I2C-Slave controller */ +#define SYS_RST_I2CM BIT(1)/* Reset I2C-Master controller */ +#define SYS_RST_LCD BIT(2)/* Reset LCD controller */ +#define SYS_RST_BM BIT(3)/* Reset Bus Management controller */ +#define SYS_RST_DSIRX BIT(4)/* Reset DSI-RX and App controller */ +#define SYS_RST_REG BIT(5)/* Reset Register module */ + +/* GPIO Registers */ +#define GPIOC 0x0520/* GPIO Control */ +#define GPIOO 0x0524/* GPIO Output */ +#define GPIOI 0x0528/* GPIO Input */ + +/* I2C Registers */ +#define I2CTIMCTRL 0x0540/* I2C IF Timing and Enable Control */ +#define I2CMADDR 0x0544/* I2C Master Addressing */ +#define WDATAQ 0x0548/* Write Data Queue */ +#define RDATAQ 0x054C/* Read Data Queue */ + +/* Chip ID and Revision ID Register */ +#define IDREG 0x0580 + +#define LPX_PERIOD 4 +#define TTA_GET 0x40000 +#define TTA_SURE 6 + +#define TC358775XBG_ID 0x00007500 + +/* Debug Registers */ +#define DEBUG00 0x05A0/* Debug */ +#define DEBUG01 0x05A4/* LVDS Data */ + +#define DSI_CLEN_BIT BIT(0) +#define DIVIDE_BY_3 3/* PCLK=DCLK/3 */ +#define DIVIDE_BY_6 6/* PCLK=DCLK/6 */ +#define LVCFG_LVEN_BIT BIT(0) + +#define L0EN BIT(1) + +#define TC358775_VPCTRL_VSDELAY__MASK 0x3FF00000 +#define TC358775_VPCTRL_VSDELAY__SHIFT 20 +static inline u32 TC358775_VPCTRL_VSDELAY (uint32_t val) +{ +return ((val) <<TC358775_VPCTRL_VSDELAY__SHIFT ) & +TC358775_VPCTRL_VSDELAY__MASK ; +} + +#define TC358775_VPCTRL_OPXLFMT__MASK 0x00000100 +#define TC358775_VPCTRL_OPXLFMT__SHIFT 8 +static inline u32 TC358775_VPCTRL_OPXLFMT (uint32_t val) +{ +return ((val) <<TC358775_VPCTRL_OPXLFMT__SHIFT ) & +TC358775_VPCTRL_OPXLFMT__MASK ; +} + +#define TC358775_VPCTRL_MSF__MASK 0x00000001 +#define TC358775_VPCTRL_MSF__SHIFT 0 +static inline u32 TC358775_VPCTRL_MSF (uint32_t val) +{ +return ((val) <<TC358775_VPCTRL_MSF__SHIFT ) & +TC358775_VPCTRL_MSF__MASK ; +} + +#define TC358775_LVCFG_PCLKDIV__MASK 0x000000f0 +#define TC358775_LVCFG_PCLKDIV__SHIFT 4 +static inline u32 TC358775_LVCFG_PCLKDIV (uint32_t val) +{ +return ((val) <<TC358775_LVCFG_PCLKDIV__SHIFT ) & +TC358775_LVCFG_PCLKDIV__MASK ; +} + +#define TC358775_LVCFG_LVDLINK__MASK 0x00000002 +#define TC358775_LVCFG_LVDLINK__SHIFT 0 +static inline u32 TC358775_LVCFG_LVDLINK (uint32_t val) +{ +return ((val) <<TC358775_LVCFG_LVDLINK__SHIFT ) & +TC358775_LVCFG_LVDLINK__MASK ; +} + +enum tc358775_ports { +TC358775_DSI_IN , +TC358775_LVDS_OUT0 , +TC358775_LVDS_OUT1 , +}; + +struct tc_data { +struct i2c_client *i2c; +struct device *dev; + +struct drm_bridge bridge; +struct drm_bridge *panel_bridge; + +struct device_node *host_node; +struct mipi_dsi_device *dsi; +u8 num_dsi_lanes; + +struct regulator *vdd; +struct regulator *vddio; +struct gpio_desc *reset_gpio; +struct gpio_desc *stby_gpio; +bool dual_link;/* single-link or dual-link */ +}; + +static inline struct tc_data *bridge_to_tc (struct drm_bridge *b) +{ + return container_of(b, struct tc_data, bridge); +} + +static void tc_bridge_pre_enable (struct drm_bridge *bridge) +{ +struct tc_data *tc =bridge_to_tc (bridge); +struct device *dev = &tc->dsi->dev; +int ret; + + ret =regulator_enable (tc->vddio); +if (ret <0 ) +dev_err (dev,"regulator vddio enable failed, %d\n" , ret); +usleep_range (10000 ,11000 ); + + ret =regulator_enable (tc->vdd); +if (ret <0 ) +dev_err (dev,"regulator vdd enable failed, %d\n" , ret); +usleep_range (10000 ,11000 ); + +gpiod_set_value (tc->stby_gpio,0 ); +usleep_range (10000 ,11000 ); + +gpiod_set_value (tc->reset_gpio,0 ); +usleep_range (10 ,20 ); +} + +static void tc_bridge_post_disable (struct drm_bridge *bridge) +{ +struct tc_data *tc =bridge_to_tc (bridge); +struct device *dev = &tc->dsi->dev; +int ret; + + ret =regulator_disable (tc->vddio); +if (ret <0 ) +dev_err (dev,"regulator vddio disable failed, %d\n" , ret); +usleep_range (10000 ,11000 ); + + ret =regulator_disable (tc->vdd); +if (ret <0 ) +dev_err (dev,"regulator vdd disable failed, %d\n" , ret); +usleep_range (10000 ,11000 ); + +gpiod_set_value (tc->stby_gpio,1 ); +usleep_range (10000 ,11000 ); + +gpiod_set_value (tc->reset_gpio,1 ); +usleep_range (10 ,20 ); +} + +static u32 d2l_read (struct i2c_client *i2c,u16 reg) +{ +int ret; +u8 val[4 ]; +u8 addr[] = {(reg >>8 ) &0xff , reg &0xff }; +u32 value; + + ret =i2c_master_send (i2c, addr,sizeof (reg)); +if (ret <0 ) + goto fail; + + ret =i2c_master_recv (i2c, val,sizeof (value)); +if (ret <0 ) + goto fail; + + value = val[3 ] <<24 | val[2 ] <<16 | val[1 ] <<8 | val[0 ]; + +pr_debug ("d2l: I2C : reg:%04x value:%08x\n" , reg, value); + +return value; + +fail: +dev_err (&i2c->dev,"Error %d reading from subaddress 0x%x\n" , + ret, reg); +return 0 ; +} + +static void d2l_write (struct i2c_client *i2c,u16 reg,u32 val) +{ +u8 buf[6 ]; +int ret; + + buf[0 ] = reg >>8 ; + buf[1 ] = reg &0xFF ; + buf[2 ] = (val >>0 ) &0xFF ; + buf[3 ] = (val >>8 ) &0xFF ; + buf[4 ] = (val >>16 ) &0xFF ; + buf[5 ] = (val >>24 ) &0xFF ; + + ret =i2c_master_send (i2c, buf,ARRAY_SIZE (buf)); +if (ret <0 ) +dev_err (&i2c->dev,"Error %d writing to subaddress 0x%x\n" , + ret, reg); +} + +/* helper function to access bus_formats */ +static struct drm_connector *get_connector (struct drm_encoder *encoder) +{ +struct drm_device *dev = encoder->dev; +struct drm_connector *connector; + +list_for_each_entry (connector, &dev->mode_config.connector_list, head) +if (connector->encoder == encoder) +return connector; + +return NULL ; +} + +static void tc_bridge_enable (struct drm_bridge *bridge) +{ +struct tc_data *tc =bridge_to_tc (bridge); +u32 hbpr, hpw, htime1, hfpr, hsize, htime2; +u32 vbpr, vpw, vtime1, vfpr, vsize, vtime2; +u32 val =0 ; +u16 bus_formats; +struct drm_display_mode *mode; +struct drm_connector *connector =get_connector (bridge->encoder); + + mode = &bridge->encoder->crtc->state->adjusted_mode; + + hbpr = mode->htotal - mode->hsync_end; + hpw = mode->hsync_end - mode->hsync_start; + vbpr = mode->vtotal - mode->vsync_end; + vpw = mode->vsync_end - mode->vsync_start; + + htime1 = (hbpr <<16 ) + hpw; + vtime1 = (vbpr <<16 ) + vpw; + + hfpr = mode->hsync_start - mode->hdisplay; + hsize = mode->hdisplay; + vfpr = mode->vsync_start - mode->vdisplay; + vsize = mode->vdisplay; + + htime2 = (hfpr <<16 ) + hsize; + vtime2 = (vfpr <<16 ) + vsize; + + val =d2l_read (tc->i2c,IDREG ); + +dev_info (tc->dev,"DSI2LVDS Chip ID.%02x Revision ID. %02x **\n" , + (val >>8 ) &0xFF , val &0xFF ); + +d2l_write (tc->i2c,SYSRST ,SYS_RST_REG |SYS_RST_DSIRX |SYS_RST_BM | +SYS_RST_LCD |SYS_RST_I2CM |SYS_RST_I2CS ); +usleep_range (30000 ,40000 ); + +d2l_write (tc->i2c,PPI_TX_RX_TA ,TTA_GET |TTA_SURE ); +d2l_write (tc->i2c,PPI_LPTXTIMECNT ,LPX_PERIOD ); +d2l_write (tc->i2c,PPI_D0S_CLRSIPOCOUNT ,3 ); +d2l_write (tc->i2c,PPI_D1S_CLRSIPOCOUNT ,3 ); +d2l_write (tc->i2c,PPI_D2S_CLRSIPOCOUNT ,3 ); +d2l_write (tc->i2c,PPI_D3S_CLRSIPOCOUNT ,3 ); + + val = ((L0EN << tc->num_dsi_lanes) -L0EN ) |DSI_CLEN_BIT ; +d2l_write (tc->i2c,PPI_LANEENABLE , val); +d2l_write (tc->i2c,DSI_LANEENABLE , val); + +d2l_write (tc->i2c,PPI_STARTPPI ,PPI_START_FUNCTION ); +d2l_write (tc->i2c,DSI_STARTDSI ,DSI_RX_START ); + + val =TC358775_VPCTRL_VSDELAY (21 ); + + bus_formats = connector->display_info.bus_formats[0 ]; +dev_dbg (tc->dev,"bus_formats : %04x\n" , bus_formats); + +if (bus_formats ==MEDIA_BUS_FMT_RGB888_1X7X4_SPWG || + bus_formats ==MEDIA_BUS_FMT_RGB888_1X7X4_JEIDA ) { +/* RGB888 */ + val |=TC358775_VPCTRL_OPXLFMT (1 ); +d2l_write (tc->i2c,VPCTRL , val); + }else { +/* RGB666 */ + val |=TC358775_VPCTRL_MSF (1 ); +d2l_write (tc->i2c,VPCTRL , val); + } + +d2l_write (tc->i2c,HTIM1 , htime1); +d2l_write (tc->i2c,VTIM1 , vtime1); +d2l_write (tc->i2c,HTIM2 , htime2); +d2l_write (tc->i2c,VTIM2 , vtime2); + +d2l_write (tc->i2c,VFUEN ,VFUEN_EN ); +d2l_write (tc->i2c,SYSRST ,SYS_RST_LCD ); +d2l_write (tc->i2c,LVPHY0 ,LV_PHY0_PRBS_ON (4 ) |LV_PHY0_ND (6 )); + +/* default jeida-24 */ +if (bus_formats ==MEDIA_BUS_FMT_RGB888_1X7X4_SPWG ) { +/* vesa-24 */ +d2l_write (tc->i2c,LV_MX0003 ,LV_MX (LVI_R0 ,LVI_R1 ,LVI_R2 ,LVI_R3 )); +d2l_write (tc->i2c,LV_MX0407 ,LV_MX (LVI_R4 ,LVI_R7 ,LVI_R5 ,LVI_G0 )); +d2l_write (tc->i2c,LV_MX0811 ,LV_MX (LVI_G1 ,LVI_G2 ,LVI_G6 ,LVI_G7 )); +d2l_write (tc->i2c,LV_MX1215 ,LV_MX (LVI_G3 ,LVI_G4 ,LVI_G5 ,LVI_B0 )); +d2l_write (tc->i2c,LV_MX1619 ,LV_MX (LVI_B6 ,LVI_B7 ,LVI_B1 ,LVI_B2 )); +d2l_write (tc->i2c,LV_MX2023 ,LV_MX (LVI_B3 ,LVI_B4 ,LVI_B5 ,LVI_L0 )); +d2l_write (tc->i2c,LV_MX2427 ,LV_MX (LVI_HS ,LVI_VS ,LVI_DE ,LVI_R6 )); + } + +if (bus_formats ==MEDIA_BUS_FMT_RGB666_1X7X3_SPWG ) { +/* jeida-18 */ +d2l_write (tc->i2c,LV_MX0003 ,LV_MX (LVI_R0 ,LVI_R1 ,LVI_R2 ,LVI_R3 )); +d2l_write (tc->i2c,LV_MX0407 ,LV_MX (LVI_R4 ,LVI_L0 ,LVI_R5 ,LVI_G0 )); +d2l_write (tc->i2c,LV_MX0811 ,LV_MX (LVI_G1 ,LVI_G2 ,LVI_L0 ,LVI_L0 )); +d2l_write (tc->i2c,LV_MX1215 ,LV_MX (LVI_G3 ,LVI_G4 ,LVI_G5 ,LVI_B0 )); +d2l_write (tc->i2c,LV_MX1619 ,LV_MX (LVI_L0 ,LVI_L0 ,LVI_B1 ,LVI_B2 )); +d2l_write (tc->i2c,LV_MX2023 ,LV_MX (LVI_B3 ,LVI_B4 ,LVI_B5 ,LVI_L0 )); +d2l_write (tc->i2c,LV_MX2427 ,LV_MX (LVI_HS ,LVI_VS ,LVI_DE ,LVI_L0 )); + } + +d2l_write (tc->i2c,VFUEN ,VFUEN_EN ); + + val =LVCFG_LVEN_BIT ; +if (tc->dual_link) { + val |=TC358775_LVCFG_LVDLINK (1 ); + val |=TC358775_LVCFG_PCLKDIV (DIVIDE_BY_6 ); + }else { + val |=TC358775_LVCFG_PCLKDIV (DIVIDE_BY_3 ); + } + +d2l_write (tc->i2c,LVCFG , val); +} + +static int tc_mode_valid (struct drm_bridge *bridge, +const struct drm_display_mode *mode) +{ +struct tc_data *tc =bridge_to_tc (bridge); + +/* Maximum pixel clock speed 135MHz-single-link/270MHz-dual-link */ +if ((mode->clock >135000 && tc->dual_link) || + (mode->clock >270000 && tc->dual_link)) +return MODE_CLOCK_HIGH ; + +return MODE_OK ; +} + +static int tc358775_parse_dt (struct device_node *np,struct tc_data *tc) +{ +struct device_node *endpoint; +struct device_node *parent; +struct device_node *remote; +struct property *prop; +int len; + + endpoint =of_graph_get_endpoint_by_regs (tc->dev->of_node, +TC358775_DSI_IN ,-1 ); +if (endpoint) { +/* dsi0_out node */ + parent =of_graph_get_remote_port_parent (endpoint); +of_node_put (endpoint); +if (parent) { +/* dsi0 port 1 */ + endpoint =of_graph_get_endpoint_by_regs (parent,1 ,-1 ); +of_node_put (parent); + prop =of_find_property (endpoint,"data-lanes" , + &len); +of_node_put (endpoint); +if (!prop) { +dev_err (tc->dev, +"failed to find data lane\n" ); +return -EPROBE_DEFER ; + } + } + } + + tc->num_dsi_lanes = len /sizeof (u32); + +if (tc->num_dsi_lanes <1 || tc->num_dsi_lanes >4 ) +return -EINVAL ; + + tc->host_node =of_graph_get_remote_node (np,0 ,0 ); +if (!tc->host_node) +return -ENODEV ; + +of_node_put (tc->host_node); + + endpoint =of_graph_get_endpoint_by_regs (tc->dev->of_node, +TC358775_LVDS_OUT1 ,-1 ); +if (endpoint) { + remote =of_graph_get_remote_port_parent (endpoint); +of_node_put (endpoint); + +if (remote) { +if (of_device_is_available (remote)) + tc->dual_link = true; +of_node_put (remote); + } + } + +dev_dbg (tc->dev,"no.of dsi lanes: %d\n" , tc->num_dsi_lanes); +dev_dbg (tc->dev,"operating in %s-link mode\n" , + tc->dual_link ?"dual" :"single" ); + +return 0 ; +} + +static int tc_bridge_attach (struct drm_bridge *bridge, +enum drm_bridge_attach_flags flags) +{ +struct tc_data *tc =bridge_to_tc (bridge); +struct device *dev = &tc->i2c->dev; +struct mipi_dsi_host *host; +struct mipi_dsi_device *dsi; +int ret; + +const struct mipi_dsi_device_info info = { .type ="tc358775" , + .channel =0 , + .node =NULL , + }; + + host =of_find_mipi_dsi_host_by_node (tc->host_node); +if (!host) { +dev_err (dev,"failed to find dsi host\n" ); +return -EPROBE_DEFER ; + } + + dsi =mipi_dsi_device_register_full (host, &info); +if (IS_ERR (dsi)) { +dev_err (dev,"failed to create dsi device\n" ); + ret =PTR_ERR (dsi); + goto err_dsi_device; + } + + tc->dsi = dsi; + + dsi->lanes = tc->num_dsi_lanes; + dsi->format =MIPI_DSI_FMT_RGB888 ; + dsi->mode_flags =MIPI_DSI_MODE_VIDEO ; + + ret =mipi_dsi_attach (dsi); +if (ret <0 ) { +dev_err (dev,"failed to attach dsi to host\n" ); + goto err_dsi_attach; + } + +/* Attach the panel-bridge to the dsi bridge */ +return drm_bridge_attach (bridge->encoder, tc->panel_bridge, + &tc->bridge, flags); +err_dsi_attach: +mipi_dsi_device_unregister (dsi); +err_dsi_device: +return ret; +} + +static const struct drm_bridge_funcs tc_bridge_funcs = { + .attach = tc_bridge_attach, + .pre_enable = tc_bridge_pre_enable, + .enable = tc_bridge_enable, + .mode_valid = tc_mode_valid, + .post_disable = tc_bridge_post_disable, +}; + +static int tc_probe (struct i2c_client *client,const struct i2c_device_id *id) +{ +struct device *dev = &client->dev; +struct drm_panel *panel; +struct tc_data *tc; +int ret; + + tc =devm_kzalloc (dev,sizeof (*tc),GFP_KERNEL ); +if (!tc) +return -ENOMEM ; + + tc->dev = dev; + tc->i2c = client; + + ret =drm_of_find_panel_or_bridge (dev->of_node,TC358775_LVDS_OUT0 , +0 , &panel,NULL ); +if (ret <0 ) +return ret; +if (!panel) +return -ENODEV ; + + tc->panel_bridge =devm_drm_panel_bridge_add (dev, panel); +if (IS_ERR (tc->panel_bridge)) +return PTR_ERR (tc->panel_bridge); + + ret =tc358775_parse_dt (dev->of_node, tc); +if (ret) +return ret; + + tc->vddio =devm_regulator_get (dev,"vddio-supply" ); +if (IS_ERR (tc->vddio)) { + ret =PTR_ERR (tc->vddio); +dev_err (dev,"vddio-supply not found\n" ); +return ret; + } + + tc->vdd =devm_regulator_get (dev,"vdd-supply" ); +if (IS_ERR (tc->vdd)) { + ret =PTR_ERR (tc->vddio); +dev_err (dev,"vdd-supply not found\n" ); +return ret; + } + + tc->stby_gpio =devm_gpiod_get (dev,"stby" ,GPIOD_OUT_HIGH ); +if (IS_ERR (tc->stby_gpio)) { + ret =PTR_ERR (tc->stby_gpio); +dev_err (dev,"cannot get stby-gpio %d\n" , ret); +return ret; + } + + tc->reset_gpio =devm_gpiod_get (dev,"reset" ,GPIOD_OUT_HIGH ); +if (IS_ERR (tc->reset_gpio)) { + ret =PTR_ERR (tc->reset_gpio); +dev_err (dev,"cannot get reset-gpios %d\n" , ret); +return ret; + } + + tc->bridge.funcs = &tc_bridge_funcs; + tc->bridge.of_node = dev->of_node; +drm_bridge_add (&tc->bridge); + +i2c_set_clientdata (client, tc); + +return 0 ; +} + +static int tc_remove (struct i2c_client *client) +{ +struct tc_data *tc =i2c_get_clientdata (client); + +drm_bridge_remove (&tc->bridge); + +return 0 ; +} + +static const struct i2c_device_id tc358775_i2c_ids[] = { + {"tc358775" ,0 }, + { } +}; +MODULE_DEVICE_TABLE (i2c, tc358775_i2c_ids); + +static const struct of_device_id tc358775_of_ids[] = { + { .compatible ="toshiba,tc358775" , }, + { } +}; +MODULE_DEVICE_TABLE (of, tc358775_of_ids); + +static struct i2c_driver tc358775_driver = { + .driver = { + .name ="tc358775" , + .of_match_table = tc358775_of_ids, + }, + .id_table = tc358775_i2c_ids, + .probe = tc_probe, + .remove = tc_remove, +}; +module_i2c_driver (tc358775_driver); + +MODULE_AUTHOR ("Vinay Simha BN <[email protected]>" ); +MODULE_DESCRIPTION ("TC358775 DSI/LVDS bridge driver" ); +MODULE_LICENSE ("GPL v2" );
Signature · 2 lines
regards, vinaysimha
Hi,
Quoted 5 lines · Vinay Simha B N
Neil,
yaml is the v3 version, there was no change , so i had not created v4 for yaml [PATCH v3 2/2] display/drm/bridge: TC358775 DSI/LVDS driver
OK, please resend the whole patchset even with unchanged patches, you can explain which patches were not changed on the cover letter.
Neil
Quoted 811 lines · Neil Armstrong
Quoted 809 lines
Hi,
Quoted 29 lines · Vinay Simha BN
Signed-off-by Vinay Simha BN <[email protected]>---
v1:
Initial versionv2:
* Andrzej Hajda review comments incorporated SPDX identifier
development debug removed
alphabetic order headers
u32 instead ofunit32_t
magic numbers to macros for CLRSI and mux registers ignored return value* Laurent Pinchart review comments incorporated
mdelay tousleep_range
bus_formatsaddedv3:
* Andrzej Hajda review comments incorporateddrm_connector_statusremoved
u32 rev removed and local variabl is used regulator enable disable with proper orders and delays as per the spec
devm_drm_panel_bridge_addmethod used instead of panel description modified
dual port implementedQuoted 8 lines
v4:
* Sam Ravnborg review comments incorporated
panel->connector_typeremoved* Reported-by: kernel test robot <[email protected]>
parse_dtto static function
removed the if (endpoint), since data-lanes has to be present for dsi dts portsI maybe missed something, but you should also post a YAML DT bindings file associated to the driver.
Neil
Quoted 761 lines
--- drivers/gpu/drm/bridge/Kconfig | 10 + drivers/gpu/drm/bridge/Makefile | 1 + drivers/gpu/drm/bridge/tc358775.c | 721 ++++++++++++++++++++++++++++++ 3 files changed, 732 insertions(+) create mode 100644 drivers/gpu/drm/bridge/tc358775.cdrivers/gpu/drm/bridge/Kconfig +10
-0@@ -181,6 +181,16 @@ config DRM_TOSHIBA_TC358768 help Toshiba TC358768AXBG/TC358778XBG DSI bridge chip driver. +config DRM_TOSHIBA_TC358775 + tristate "Toshiba TC358775 LVDS bridge" + depends on OF + select DRM_KMS_HELPER + select REGMAP_I2C + select DRM_PANEL + select DRM_MIPI_DSI + ---help--- + Toshiba TC358775 LVDS bridge chip driver. + config DRM_TI_TFP410 tristate "TI TFP410 DVI/HDMI bridge" depends on OFdrivers/gpu/drm/bridge/Makefile +1
-0@@ -15,6 +15,7 @@ obj-$(CONFIG_DRM_THINE_THC63LVD1024) += thc63lvd1024.o obj-$(CONFIG_DRM_TOSHIBA_TC358764) += tc358764.o obj-$(CONFIG_DRM_TOSHIBA_TC358767) += tc358767.o obj-$(CONFIG_DRM_TOSHIBA_TC358768) += tc358768.o +obj-$(CONFIG_DRM_TOSHIBA_TC358775) += tc358775.o obj-$(CONFIG_DRM_I2C_ADV7511) += adv7511/ obj-$(CONFIG_DRM_TI_SN65DSI86) += ti-sn65dsi86.o obj-$(CONFIG_DRM_TI_TFP410) += ti-tfp410.odrivers/gpu/drm/bridge/tc358775.c new file +715
-0@@ -0,0 +1,721 @@ +// SPDX-License-Identifier: GPL-2.0 +/* +* tc358775 DSI to LVDS bridge driver +* +* Copyright (C) 2020 SMART Wireless Computing +* Author: Vinay Simha BN <[email protected]> +* +*/ +//#define DEBUG +#include <linux/clk.h> +#include <linux/device.h> +#include <linux/gpio/consumer.h> +#include <linux/i2c.h> +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/regulator/consumer.h> +#include <linux/slab.h> + +#include <drm/drm_atomic_helper.h> +#include <drm/drm_bridge.h> +#include <drm/drm_crtc_helper.h> +#include <drm/drm_dp_helper.h> +#include <drm/drm_mipi_dsi.h> +#include <drm/drm_of.h> +#include <drm/drm_panel.h> +#include <drm/drm_probe_helper.h> + +#define FLD_MASK (start, end) (((1 << ((start) - (end) + 1)) - 1) << (end)) +#define FLD_VAL (val, start, end) (((val) << (end)) & FLD_MASK(start, end)) + +/* Registers */ + +/* DSI D-PHY Layer Registers */ +#define D0W_DPHYCONTTX 0x0004/* Data Lane 0 DPHY Tx Control */ +#define CLW_DPHYCONTRX 0x0020/* Clock Lane DPHY Rx Control */ +#define D0W_DPHYCONTRX 0x0024/* Data Lane 0 DPHY Rx Control */ +#define D1W_DPHYCONTRX 0x0028/* Data Lane 1 DPHY Rx Control */ +#define D2W_DPHYCONTRX 0x002C/* Data Lane 2 DPHY Rx Control */ +#define D3W_DPHYCONTRX 0x0030/* Data Lane 3 DPHY Rx Control */ +#define COM_DPHYCONTRX 0x0038/* DPHY Rx Common Control */ +#define CLW_CNTRL 0x0040/* Clock Lane Control */ +#define D0W_CNTRL 0x0044/* Data Lane 0 Control */ +#define D1W_CNTRL 0x0048/* Data Lane 1 Control */ +#define D2W_CNTRL 0x004C/* Data Lane 2 Control */ +#define D3W_CNTRL 0x0050/* Data Lane 3 Control */ +#define DFTMODE_CNTRL 0x0054/* DFT Mode Control */ + +/* DSI PPI Layer Registers */ +#define PPI_STARTPPI 0x0104/* START control bit of PPI-TX function. */ +#define PPI_START_FUNCTION 1 + +#define PPI_BUSYPPI 0x0108 +#define PPI_LINEINITCNT 0x0110/* Line Initialization Wait Counter */ +#define PPI_LPTXTIMECNT 0x0114 +#define PPI_LANEENABLE 0x0134/* Enables each lane at the PPI layer. */ +#define PPI_TX_RX_TA 0x013C/* DSI Bus Turn Around timing parameters */ + +/* Analog timer function enable */ +#define PPI_CLS_ATMR 0x0140/* Delay for Clock Lane in LPRX */ +#define PPI_D0S_ATMR 0x0144/* Delay for Data Lane 0 in LPRX */ +#define PPI_D1S_ATMR 0x0148/* Delay for Data Lane 1 in LPRX */ +#define PPI_D2S_ATMR 0x014C/* Delay for Data Lane 2 in LPRX */ +#define PPI_D3S_ATMR 0x0150/* Delay for Data Lane 3 in LPRX */ + +#define PPI_D0S_CLRSIPOCOUNT 0x0164/* For lane 0 */ +#define PPI_D1S_CLRSIPOCOUNT 0x0168/* For lane 1 */ +#define PPI_D2S_CLRSIPOCOUNT 0x016C/* For lane 2 */ +#define PPI_D3S_CLRSIPOCOUNT 0x0170/* For lane 3 */ + +#define CLS_PRE 0x0180/* Digital Counter inside of PHY IO */ +#define D0S_PRE 0x0184/* Digital Counter inside of PHY IO */ +#define D1S_PRE 0x0188/* Digital Counter inside of PHY IO */ +#define D2S_PRE 0x018C/* Digital Counter inside of PHY IO */ +#define D3S_PRE 0x0190/* Digital Counter inside of PHY IO */ +#define CLS_PREP 0x01A0/* Digital Counter inside of PHY IO */ +#define D0S_PREP 0x01A4/* Digital Counter inside of PHY IO */ +#define D1S_PREP 0x01A8/* Digital Counter inside of PHY IO */ +#define D2S_PREP 0x01AC/* Digital Counter inside of PHY IO */ +#define D3S_PREP 0x01B0/* Digital Counter inside of PHY IO */ +#define CLS_ZERO 0x01C0/* Digital Counter inside of PHY IO */ +#define D0S_ZERO 0x01C4/* Digital Counter inside of PHY IO */ +#define D1S_ZERO 0x01C8/* Digital Counter inside of PHY IO */ +#define D2S_ZERO 0x01CC/* Digital Counter inside of PHY IO */ +#define D3S_ZERO 0x01D0/* Digital Counter inside of PHY IO */ + +#define PPI_CLRFLG 0x01E0/* PRE Counters has reached set values */ +#define PPI_CLRSIPO 0x01E4/* Clear SIPO values, Slave mode use only. */ +#define HSTIMEOUT 0x01F0/* HS Rx Time Out Counter */ +#define HSTIMEOUTENABLE 0x01F4/* Enable HS Rx Time Out Counter */ +#define DSI_STARTDSI 0x0204/* START control bit of DSI-TX function */ +#define DSI_RX_START 1 + +#define DSI_BUSYDSI 0x0208 +#define DSI_LANEENABLE 0x0210/* Enables each lane at the Protocol layer. */ +#define DSI_LANESTATUS0 0x0214/* Displays lane is in HS RX mode. */ +#define DSI_LANESTATUS1 0x0218/* Displays lane is in ULPS or STOP state */ + +#define DSI_INTSTATUS 0x0220/* Interrupt Status */ +#define DSI_INTMASK 0x0224/* Interrupt Mask */ +#define DSI_INTCLR 0x0228/* Interrupt Clear */ +#define DSI_LPTXTO 0x0230/* Low Power Tx Time Out Counter */ + +#define DSIERRCNT 0x0300/* DSI Error Count */ +#define APLCTRL 0x0400/* Application Layer Control */ +#define RDPKTLN 0x0404/* Command Read Packet Length */ + +#define VPCTRL 0x0450/* Video Path Control */ +#define HTIM1 0x0454/* Horizontal Timing Control 1 */ +#define HTIM2 0x0458/* Horizontal Timing Control 2 */ +#define VTIM1 0x045C/* Vertical Timing Control 1 */ +#define VTIM2 0x0460/* Vertical Timing Control 2 */ +#define VFUEN 0x0464/* Video Frame Timing Update Enable */ +#define VFUEN_EN BIT(0)/* Upload Enable */ + +/* Mux Input Select for LVDS LINK Input */ +#define LV_MX0003 0x0480/* Bit 0 to 3 */ +#define LV_MX0407 0x0484/* Bit 4 to 7 */ +#define LV_MX0811 0x0488/* Bit 8 to 11 */ +#define LV_MX1215 0x048C/* Bit 12 to 15 */ +#define LV_MX1619 0x0490/* Bit 16 to 19 */ +#define LV_MX2023 0x0494/* Bit 20 to 23 */ +#define LV_MX2427 0x0498/* Bit 24 to 27 */ +#define LV_MX (b0, b1, b2, b3) (FLD_VAL(b0, 4, 0) | FLD_VAL(b1, 12, 8) | \ + FLD_VAL(b2, 20, 16) | FLD_VAL(b3, 28, 24)) + +/* Input bit numbers used in mux registers */ +enum { +LVI_R0 , +LVI_R1 , +LVI_R2 , +LVI_R3 , +LVI_R4 , +LVI_R5 , +LVI_R6 , +LVI_R7 , +LVI_G0 , +LVI_G1 , +LVI_G2 , +LVI_G3 , +LVI_G4 , +LVI_G5 , +LVI_G6 , +LVI_G7 , +LVI_B0 , +LVI_B1 , +LVI_B2 , +LVI_B3 , +LVI_B4 , +LVI_B5 , +LVI_B6 , +LVI_B7 , +LVI_HS , +LVI_VS , +LVI_DE , +LVI_L0 +}; + +#define LVCFG 0x049C/* LVDS Configuration */ +#define LVPHY0 0x04A0/* LVDS PHY 0 */ +#define LV_PHY0_RST (v) FLD_VAL(v, 22, 22)/* PHY reset */ +#define LV_PHY0_IS (v) FLD_VAL(v, 15, 14) +#define LV_PHY0_ND (v) FLD_VAL(v, 4, 0)/* Frequency range select */ +#define LV_PHY0_PRBS_ON (v) FLD_VAL(v, 20, 16)/* Clock/Data Flag pins */ + +#define LVPHY1 0x04A4/* LVDS PHY 1 */ +#define SYSSTAT 0x0500/* System Status */ +#define SYSRST 0x0504/* System Reset */ + +#define SYS_RST_I2CS BIT(0)/* Reset I2C-Slave controller */ +#define SYS_RST_I2CM BIT(1)/* Reset I2C-Master controller */ +#define SYS_RST_LCD BIT(2)/* Reset LCD controller */ +#define SYS_RST_BM BIT(3)/* Reset Bus Management controller */ +#define SYS_RST_DSIRX BIT(4)/* Reset DSI-RX and App controller */ +#define SYS_RST_REG BIT(5)/* Reset Register module */ + +/* GPIO Registers */ +#define GPIOC 0x0520/* GPIO Control */ +#define GPIOO 0x0524/* GPIO Output */ +#define GPIOI 0x0528/* GPIO Input */ + +/* I2C Registers */ +#define I2CTIMCTRL 0x0540/* I2C IF Timing and Enable Control */ +#define I2CMADDR 0x0544/* I2C Master Addressing */ +#define WDATAQ 0x0548/* Write Data Queue */ +#define RDATAQ 0x054C/* Read Data Queue */ + +/* Chip ID and Revision ID Register */ +#define IDREG 0x0580 + +#define LPX_PERIOD 4 +#define TTA_GET 0x40000 +#define TTA_SURE 6 + +#define TC358775XBG_ID 0x00007500 + +/* Debug Registers */ +#define DEBUG00 0x05A0/* Debug */ +#define DEBUG01 0x05A4/* LVDS Data */ + +#define DSI_CLEN_BIT BIT(0) +#define DIVIDE_BY_3 3/* PCLK=DCLK/3 */ +#define DIVIDE_BY_6 6/* PCLK=DCLK/6 */ +#define LVCFG_LVEN_BIT BIT(0) + +#define L0EN BIT(1) + +#define TC358775_VPCTRL_VSDELAY__MASK 0x3FF00000 +#define TC358775_VPCTRL_VSDELAY__SHIFT 20 +static inline u32 TC358775_VPCTRL_VSDELAY (uint32_t val) +{ +return ((val) <<TC358775_VPCTRL_VSDELAY__SHIFT ) & +TC358775_VPCTRL_VSDELAY__MASK ; +} + +#define TC358775_VPCTRL_OPXLFMT__MASK 0x00000100 +#define TC358775_VPCTRL_OPXLFMT__SHIFT 8 +static inline u32 TC358775_VPCTRL_OPXLFMT (uint32_t val) +{ +return ((val) <<TC358775_VPCTRL_OPXLFMT__SHIFT ) & +TC358775_VPCTRL_OPXLFMT__MASK ; +} + +#define TC358775_VPCTRL_MSF__MASK 0x00000001 +#define TC358775_VPCTRL_MSF__SHIFT 0 +static inline u32 TC358775_VPCTRL_MSF (uint32_t val) +{ +return ((val) <<TC358775_VPCTRL_MSF__SHIFT ) & +TC358775_VPCTRL_MSF__MASK ; +} + +#define TC358775_LVCFG_PCLKDIV__MASK 0x000000f0 +#define TC358775_LVCFG_PCLKDIV__SHIFT 4 +static inline u32 TC358775_LVCFG_PCLKDIV (uint32_t val) +{ +return ((val) <<TC358775_LVCFG_PCLKDIV__SHIFT ) & +TC358775_LVCFG_PCLKDIV__MASK ; +} + +#define TC358775_LVCFG_LVDLINK__MASK 0x00000002 +#define TC358775_LVCFG_LVDLINK__SHIFT 0 +static inline u32 TC358775_LVCFG_LVDLINK (uint32_t val) +{ +return ((val) <<TC358775_LVCFG_LVDLINK__SHIFT ) & +TC358775_LVCFG_LVDLINK__MASK ; +} + +enum tc358775_ports { +TC358775_DSI_IN , +TC358775_LVDS_OUT0 , +TC358775_LVDS_OUT1 , +}; + +struct tc_data { +struct i2c_client *i2c; +struct device *dev; + +struct drm_bridge bridge; +struct drm_bridge *panel_bridge; + +struct device_node *host_node; +struct mipi_dsi_device *dsi; +u8 num_dsi_lanes; + +struct regulator *vdd; +struct regulator *vddio; +struct gpio_desc *reset_gpio; +struct gpio_desc *stby_gpio; +bool dual_link;/* single-link or dual-link */ +}; + +static inline struct tc_data *bridge_to_tc (struct drm_bridge *b) +{ + return container_of(b, struct tc_data, bridge); +} + +static void tc_bridge_pre_enable (struct drm_bridge *bridge) +{ +struct tc_data *tc =bridge_to_tc (bridge); +struct device *dev = &tc->dsi->dev; +int ret; + + ret =regulator_enable (tc->vddio); +if (ret <0 ) +dev_err (dev,"regulator vddio enable failed, %d\n" , ret); +usleep_range (10000 ,11000 ); + + ret =regulator_enable (tc->vdd); +if (ret <0 ) +dev_err (dev,"regulator vdd enable failed, %d\n" , ret); +usleep_range (10000 ,11000 ); + +gpiod_set_value (tc->stby_gpio,0 ); +usleep_range (10000 ,11000 ); + +gpiod_set_value (tc->reset_gpio,0 ); +usleep_range (10 ,20 ); +} + +static void tc_bridge_post_disable (struct drm_bridge *bridge) +{ +struct tc_data *tc =bridge_to_tc (bridge); +struct device *dev = &tc->dsi->dev; +int ret; + + ret =regulator_disable (tc->vddio); +if (ret <0 ) +dev_err (dev,"regulator vddio disable failed, %d\n" , ret); +usleep_range (10000 ,11000 ); + + ret =regulator_disable (tc->vdd); +if (ret <0 ) +dev_err (dev,"regulator vdd disable failed, %d\n" , ret); +usleep_range (10000 ,11000 ); + +gpiod_set_value (tc->stby_gpio,1 ); +usleep_range (10000 ,11000 ); + +gpiod_set_value (tc->reset_gpio,1 ); +usleep_range (10 ,20 ); +} + +static u32 d2l_read (struct i2c_client *i2c,u16 reg) +{ +int ret; +u8 val[4 ]; +u8 addr[] = {(reg >>8 ) &0xff , reg &0xff }; +u32 value; + + ret =i2c_master_send (i2c, addr,sizeof (reg)); +if (ret <0 ) + goto fail; + + ret =i2c_master_recv (i2c, val,sizeof (value)); +if (ret <0 ) + goto fail; + + value = val[3 ] <<24 | val[2 ] <<16 | val[1 ] <<8 | val[0 ]; + +pr_debug ("d2l: I2C : reg:%04x value:%08x\n" , reg, value); + +return value; + +fail: +dev_err (&i2c->dev,"Error %d reading from subaddress 0x%x\n" , + ret, reg); +return 0 ; +} + +static void d2l_write (struct i2c_client *i2c,u16 reg,u32 val) +{ +u8 buf[6 ]; +int ret; + + buf[0 ] = reg >>8 ; + buf[1 ] = reg &0xFF ; + buf[2 ] = (val >>0 ) &0xFF ; + buf[3 ] = (val >>8 ) &0xFF ; + buf[4 ] = (val >>16 ) &0xFF ; + buf[5 ] = (val >>24 ) &0xFF ; + + ret =i2c_master_send (i2c, buf,ARRAY_SIZE (buf)); +if (ret <0 ) +dev_err (&i2c->dev,"Error %d writing to subaddress 0x%x\n" , + ret, reg); +} + +/* helper function to access bus_formats */ +static struct drm_connector *get_connector (struct drm_encoder *encoder) +{ +struct drm_device *dev = encoder->dev; +struct drm_connector *connector; + +list_for_each_entry (connector, &dev->mode_config.connector_list, head) +if (connector->encoder == encoder) +return connector; + +return NULL ; +} + +static void tc_bridge_enable (struct drm_bridge *bridge) +{ +struct tc_data *tc =bridge_to_tc (bridge); +u32 hbpr, hpw, htime1, hfpr, hsize, htime2; +u32 vbpr, vpw, vtime1, vfpr, vsize, vtime2; +u32 val =0 ; +u16 bus_formats; +struct drm_display_mode *mode; +struct drm_connector *connector =get_connector (bridge->encoder); + + mode = &bridge->encoder->crtc->state->adjusted_mode; + + hbpr = mode->htotal - mode->hsync_end; + hpw = mode->hsync_end - mode->hsync_start; + vbpr = mode->vtotal - mode->vsync_end; + vpw = mode->vsync_end - mode->vsync_start; + + htime1 = (hbpr <<16 ) + hpw; + vtime1 = (vbpr <<16 ) + vpw; + + hfpr = mode->hsync_start - mode->hdisplay; + hsize = mode->hdisplay; + vfpr = mode->vsync_start - mode->vdisplay; + vsize = mode->vdisplay; + + htime2 = (hfpr <<16 ) + hsize; + vtime2 = (vfpr <<16 ) + vsize; + + val =d2l_read (tc->i2c,IDREG ); + +dev_info (tc->dev,"DSI2LVDS Chip ID.%02x Revision ID. %02x **\n" , + (val >>8 ) &0xFF , val &0xFF ); + +d2l_write (tc->i2c,SYSRST ,SYS_RST_REG |SYS_RST_DSIRX |SYS_RST_BM | +SYS_RST_LCD |SYS_RST_I2CM |SYS_RST_I2CS ); +usleep_range (30000 ,40000 ); + +d2l_write (tc->i2c,PPI_TX_RX_TA ,TTA_GET |TTA_SURE ); +d2l_write (tc->i2c,PPI_LPTXTIMECNT ,LPX_PERIOD ); +d2l_write (tc->i2c,PPI_D0S_CLRSIPOCOUNT ,3 ); +d2l_write (tc->i2c,PPI_D1S_CLRSIPOCOUNT ,3 ); +d2l_write (tc->i2c,PPI_D2S_CLRSIPOCOUNT ,3 ); +d2l_write (tc->i2c,PPI_D3S_CLRSIPOCOUNT ,3 ); + + val = ((L0EN << tc->num_dsi_lanes) -L0EN ) |DSI_CLEN_BIT ; +d2l_write (tc->i2c,PPI_LANEENABLE , val); +d2l_write (tc->i2c,DSI_LANEENABLE , val); + +d2l_write (tc->i2c,PPI_STARTPPI ,PPI_START_FUNCTION ); +d2l_write (tc->i2c,DSI_STARTDSI ,DSI_RX_START ); + + val =TC358775_VPCTRL_VSDELAY (21 ); + + bus_formats = connector->display_info.bus_formats[0 ]; +dev_dbg (tc->dev,"bus_formats : %04x\n" , bus_formats); + +if (bus_formats ==MEDIA_BUS_FMT_RGB888_1X7X4_SPWG || + bus_formats ==MEDIA_BUS_FMT_RGB888_1X7X4_JEIDA ) { +/* RGB888 */ + val |=TC358775_VPCTRL_OPXLFMT (1 ); +d2l_write (tc->i2c,VPCTRL , val); + }else { +/* RGB666 */ + val |=TC358775_VPCTRL_MSF (1 ); +d2l_write (tc->i2c,VPCTRL , val); + } + +d2l_write (tc->i2c,HTIM1 , htime1); +d2l_write (tc->i2c,VTIM1 , vtime1); +d2l_write (tc->i2c,HTIM2 , htime2); +d2l_write (tc->i2c,VTIM2 , vtime2); + +d2l_write (tc->i2c,VFUEN ,VFUEN_EN ); +d2l_write (tc->i2c,SYSRST ,SYS_RST_LCD ); +d2l_write (tc->i2c,LVPHY0 ,LV_PHY0_PRBS_ON (4 ) |LV_PHY0_ND (6 )); + +/* default jeida-24 */ +if (bus_formats ==MEDIA_BUS_FMT_RGB888_1X7X4_SPWG ) { +/* vesa-24 */ +d2l_write (tc->i2c,LV_MX0003 ,LV_MX (LVI_R0 ,LVI_R1 ,LVI_R2 ,LVI_R3 )); +d2l_write (tc->i2c,LV_MX0407 ,LV_MX (LVI_R4 ,LVI_R7 ,LVI_R5 ,LVI_G0 )); +d2l_write (tc->i2c,LV_MX0811 ,LV_MX (LVI_G1 ,LVI_G2 ,LVI_G6 ,LVI_G7 )); +d2l_write (tc->i2c,LV_MX1215 ,LV_MX (LVI_G3 ,LVI_G4 ,LVI_G5 ,LVI_B0 )); +d2l_write (tc->i2c,LV_MX1619 ,LV_MX (LVI_B6 ,LVI_B7 ,LVI_B1 ,LVI_B2 )); +d2l_write (tc->i2c,LV_MX2023 ,LV_MX (LVI_B3 ,LVI_B4 ,LVI_B5 ,LVI_L0 )); +d2l_write (tc->i2c,LV_MX2427 ,LV_MX (LVI_HS ,LVI_VS ,LVI_DE ,LVI_R6 )); + } + +if (bus_formats ==MEDIA_BUS_FMT_RGB666_1X7X3_SPWG ) { +/* jeida-18 */ +d2l_write (tc->i2c,LV_MX0003 ,LV_MX (LVI_R0 ,LVI_R1 ,LVI_R2 ,LVI_R3 )); +d2l_write (tc->i2c,LV_MX0407 ,LV_MX (LVI_R4 ,LVI_L0 ,LVI_R5 ,LVI_G0 )); +d2l_write (tc->i2c,LV_MX0811 ,LV_MX (LVI_G1 ,LVI_G2 ,LVI_L0 ,LVI_L0 )); +d2l_write (tc->i2c,LV_MX1215 ,LV_MX (LVI_G3 ,LVI_G4 ,LVI_G5 ,LVI_B0 )); +d2l_write (tc->i2c,LV_MX1619 ,LV_MX (LVI_L0 ,LVI_L0 ,LVI_B1 ,LVI_B2 )); +d2l_write (tc->i2c,LV_MX2023 ,LV_MX (LVI_B3 ,LVI_B4 ,LVI_B5 ,LVI_L0 )); +d2l_write (tc->i2c,LV_MX2427 ,LV_MX (LVI_HS ,LVI_VS ,LVI_DE ,LVI_L0 )); + } + +d2l_write (tc->i2c,VFUEN ,VFUEN_EN ); + + val =LVCFG_LVEN_BIT ; +if (tc->dual_link) { + val |=TC358775_LVCFG_LVDLINK (1 ); + val |=TC358775_LVCFG_PCLKDIV (DIVIDE_BY_6 ); + }else { + val |=TC358775_LVCFG_PCLKDIV (DIVIDE_BY_3 ); + } + +d2l_write (tc->i2c,LVCFG , val); +} + +static int tc_mode_valid (struct drm_bridge *bridge, +const struct drm_display_mode *mode) +{ +struct tc_data *tc =bridge_to_tc (bridge); + +/* Maximum pixel clock speed 135MHz-single-link/270MHz-dual-link */ +if ((mode->clock >135000 && tc->dual_link) || + (mode->clock >270000 && tc->dual_link)) +return MODE_CLOCK_HIGH ; + +return MODE_OK ; +} + +static int tc358775_parse_dt (struct device_node *np,struct tc_data *tc) +{ +struct device_node *endpoint; +struct device_node *parent; +struct device_node *remote; +struct property *prop; +int len; + + endpoint =of_graph_get_endpoint_by_regs (tc->dev->of_node, +TC358775_DSI_IN ,-1 ); +if (endpoint) { +/* dsi0_out node */ + parent =of_graph_get_remote_port_parent (endpoint); +of_node_put (endpoint); +if (parent) { +/* dsi0 port 1 */ + endpoint =of_graph_get_endpoint_by_regs (parent,1 ,-1 ); +of_node_put (parent); + prop =of_find_property (endpoint,"data-lanes" , + &len); +of_node_put (endpoint); +if (!prop) { +dev_err (tc->dev, +"failed to find data lane\n" ); +return -EPROBE_DEFER ; + } + } + } + + tc->num_dsi_lanes = len /sizeof (u32); + +if (tc->num_dsi_lanes <1 || tc->num_dsi_lanes >4 ) +return -EINVAL ; + + tc->host_node =of_graph_get_remote_node (np,0 ,0 ); +if (!tc->host_node) +return -ENODEV ; + +of_node_put (tc->host_node); + + endpoint =of_graph_get_endpoint_by_regs (tc->dev->of_node, +TC358775_LVDS_OUT1 ,-1 ); +if (endpoint) { + remote =of_graph_get_remote_port_parent (endpoint); +of_node_put (endpoint); + +if (remote) { +if (of_device_is_available (remote)) + tc->dual_link = true; +of_node_put (remote); + } + } + +dev_dbg (tc->dev,"no.of dsi lanes: %d\n" , tc->num_dsi_lanes); +dev_dbg (tc->dev,"operating in %s-link mode\n" , + tc->dual_link ?"dual" :"single" ); + +return 0 ; +} + +static int tc_bridge_attach (struct drm_bridge *bridge, +enum drm_bridge_attach_flags flags) +{ +struct tc_data *tc =bridge_to_tc (bridge); +struct device *dev = &tc->i2c->dev; +struct mipi_dsi_host *host; +struct mipi_dsi_device *dsi; +int ret; + +const struct mipi_dsi_device_info info = { .type ="tc358775" , + .channel =0 , + .node =NULL , + }; + + host =of_find_mipi_dsi_host_by_node (tc->host_node); +if (!host) { +dev_err (dev,"failed to find dsi host\n" ); +return -EPROBE_DEFER ; + } + + dsi =mipi_dsi_device_register_full (host, &info); +if (IS_ERR (dsi)) { +dev_err (dev,"failed to create dsi device\n" ); + ret =PTR_ERR (dsi); + goto err_dsi_device; + } + + tc->dsi = dsi; + + dsi->lanes = tc->num_dsi_lanes; + dsi->format =MIPI_DSI_FMT_RGB888 ; + dsi->mode_flags =MIPI_DSI_MODE_VIDEO ; + + ret =mipi_dsi_attach (dsi); +if (ret <0 ) { +dev_err (dev,"failed to attach dsi to host\n" ); + goto err_dsi_attach; + } + +/* Attach the panel-bridge to the dsi bridge */ +return drm_bridge_attach (bridge->encoder, tc->panel_bridge, + &tc->bridge, flags); +err_dsi_attach: +mipi_dsi_device_unregister (dsi); +err_dsi_device: +return ret; +} + +static const struct drm_bridge_funcs tc_bridge_funcs = { + .attach = tc_bridge_attach, + .pre_enable = tc_bridge_pre_enable, + .enable = tc_bridge_enable, + .mode_valid = tc_mode_valid, + .post_disable = tc_bridge_post_disable, +}; + +static int tc_probe (struct i2c_client *client,const struct i2c_device_id *id) +{ +struct device *dev = &client->dev; +struct drm_panel *panel; +struct tc_data *tc; +int ret; + + tc =devm_kzalloc (dev,sizeof (*tc),GFP_KERNEL ); +if (!tc) +return -ENOMEM ; + + tc->dev = dev; + tc->i2c = client; + + ret =drm_of_find_panel_or_bridge (dev->of_node,TC358775_LVDS_OUT0 , +0 , &panel,NULL ); +if (ret <0 ) +return ret; +if (!panel) +return -ENODEV ; + + tc->panel_bridge =devm_drm_panel_bridge_add (dev, panel); +if (IS_ERR (tc->panel_bridge)) +return PTR_ERR (tc->panel_bridge); + + ret =tc358775_parse_dt (dev->of_node, tc); +if (ret) +return ret; + + tc->vddio =devm_regulator_get (dev,"vddio-supply" ); +if (IS_ERR (tc->vddio)) { + ret =PTR_ERR (tc->vddio); +dev_err (dev,"vddio-supply not found\n" ); +return ret; + } + + tc->vdd =devm_regulator_get (dev,"vdd-supply" ); +if (IS_ERR (tc->vdd)) { + ret =PTR_ERR (tc->vddio); +dev_err (dev,"vdd-supply not found\n" ); +return ret; + } + + tc->stby_gpio =devm_gpiod_get (dev,"stby" ,GPIOD_OUT_HIGH ); +if (IS_ERR (tc->stby_gpio)) { + ret =PTR_ERR (tc->stby_gpio); +dev_err (dev,"cannot get stby-gpio %d\n" , ret); +return ret; + } + + tc->reset_gpio =devm_gpiod_get (dev,"reset" ,GPIOD_OUT_HIGH ); +if (IS_ERR (tc->reset_gpio)) { + ret =PTR_ERR (tc->reset_gpio); +dev_err (dev,"cannot get reset-gpios %d\n" , ret); +return ret; + } + + tc->bridge.funcs = &tc_bridge_funcs; + tc->bridge.of_node = dev->of_node; +drm_bridge_add (&tc->bridge); + +i2c_set_clientdata (client, tc); + +return 0 ; +} + +static int tc_remove (struct i2c_client *client) +{ +struct tc_data *tc =i2c_get_clientdata (client); + +drm_bridge_remove (&tc->bridge); + +return 0 ; +} + +static const struct i2c_device_id tc358775_i2c_ids[] = { + {"tc358775" ,0 }, + { } +}; +MODULE_DEVICE_TABLE (i2c, tc358775_i2c_ids); + +static const struct of_device_id tc358775_of_ids[] = { + { .compatible ="toshiba,tc358775" , }, + { } +}; +MODULE_DEVICE_TABLE (of, tc358775_of_ids); + +static struct i2c_driver tc358775_driver = { + .driver = { + .name ="tc358775" , + .of_match_table = tc358775_of_ids, + }, + .id_table = tc358775_i2c_ids, + .probe = tc_probe, + .remove = tc_remove,
Quoted 10 lines
Quoted 8 lines
drivers/gpu/drm/bridge/tc358775.c line 721
Quoted 7 lines
drivers/gpu/drm/bridge/tc358775.c new file +6
-0+}; +module_i2c_driver (tc358775_driver); + +MODULE_AUTHOR ("Vinay Simha BN <[email protected]>" ); +MODULE_DESCRIPTION ("TC358775 DSI/LVDS bridge driver" ); +MODULE_LICENSE ("GPL v2" );
_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel