m68k: Remove astro_mcf5373l board
PATCH 1/1 m68k: Remove astro_mcf5373l board
This board is currently unmaintained. Remove it.
---
Cc: Huan Wang <[email protected]>
Cc: Angelo Dureghello <[email protected]>
Cc: Wolfgang Wegner <[email protected]>
--- arch/m68k/Kconfig | 5 - arch/m68k/dts/Makefile | 1 - arch/m68k/dts/astro_mcf5373l.dts | 27 -- board/astro/mcf5373l/Kconfig | 15 -- board/astro/mcf5373l/MAINTAINERS | 6 - board/astro/mcf5373l/Makefile | 6 - board/astro/mcf5373l/astro.h | 44 ---- board/astro/mcf5373l/fpga.c | 407 ------------------------------- board/astro/mcf5373l/mcf5373l.c | 201 --------------- configs/astro_mcf5373l_defconfig | 51 ---- include/configs/astro_mcf5373l.h | 187 -------------- 11 files changed, 950 deletions(-) delete mode 100644 arch/m68k/dts/astro_mcf5373l.dts delete mode 100644 board/astro/mcf5373l/Kconfig delete mode 100644 board/astro/mcf5373l/MAINTAINERS delete mode 100644 board/astro/mcf5373l/Makefile delete mode 100644 board/astro/mcf5373l/astro.h delete mode 100644 board/astro/mcf5373l/fpga.c delete mode 100644 board/astro/mcf5373l/mcf5373l.c delete mode 100644 configs/astro_mcf5373l_defconfig delete mode 100644 include/configs/astro_mcf5373l.h
arch/m68k/Kconfig +0 -5
@@ -155,10 +155,6 @@ config TARGET_M5282EVB bool "Support M5282EVB" select M5282 -config TARGET_ASTRO_MCF5373L - bool "Support astro_mcf5373l" - select M5373 - config TARGET_M53017EVB bool "Support M53017EVB" select M53015
@@ -183,7 +179,6 @@ config TARGET_STMARK2 endchoice source "board/BuS/eb_cpu5282/Kconfig" -source "board/astro/mcf5373l/Kconfig" source "board/cobra5272/Kconfig" source "board/freescale/m5208evbe/Kconfig" source "board/freescale/m5235evb/Kconfig"
arch/m68k/dts/Makefile +0 -1
@@ -11,7 +11,6 @@ dtb-$(CONFIG_TARGET_M5253DEMO) += M5253DEMO.dtb dtb-$(CONFIG_TARGET_M5272C3) += M5272C3.dtb dtb-$(CONFIG_TARGET_M5275EVB) += M5275EVB.dtb dtb-$(CONFIG_TARGET_M5282EVB) += M5282EVB.dtb -dtb-$(CONFIG_TARGET_ASTRO_MCF5373L) += astro_mcf5373l.dtb dtb-$(CONFIG_TARGET_M53017EVB) += M53017EVB.dtb dtb-$(CONFIG_TARGET_M5329EVB) += M5329AFEE.dtb M5329BFEE.dtb dtb-$(CONFIG_TARGET_M5373EVB) += M5373EVB.dtb
arch/m68k/dts/astro_mcf5373l.dts deleted +0 -27
@@ -1,27 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * Copyright (C) 2018 Angelo Dureghello <[email protected]> - */ - -/dts-v1/; -/include/ "mcf537x.dtsi" - -/ { - model = "Astro mcf5373l"; - compatible = "astro,mcf5373l"; - - chosen { - stdout-path = "serial0:115200n8"; - }; -}; - -&uart0 { - bootph-all; - status = "okay"; -}; - -&i2c0 { - clock-frequency = <80000>; - u-boot,i2c-slave-addr = <0x7f>; - status = "okay"; -};
board/astro/mcf5373l/Kconfig deleted +0 -15
@@ -1,15 +0,0 @@ -if TARGET_ASTRO_MCF5373L - -config SYS_CPU - default "mcf532x" - -config SYS_BOARD - default "mcf5373l" - -config SYS_VENDOR - default "astro" - -config SYS_CONFIG_NAME - default "astro_mcf5373l" - -endif
board/astro/mcf5373l/MAINTAINERS deleted +0 -6
@@ -1,6 +0,0 @@ -MCF5373L BOARD -M: Wolfgang Wegner <[email protected]> -S: Maintained -F: board/astro/mcf5373l/ -F: include/configs/astro_mcf5373l.h -F: configs/astro_mcf5373l_defconfig
board/astro/mcf5373l/Makefile deleted +0 -6
@@ -1,6 +0,0 @@ -# SPDX-License-Identifier: GPL-2.0+ -# -# (C) Copyright 2000-2006 -# Wolfgang Denk, DENX Software Engineering, [email protected]. - -obj-y = mcf5373l.o fpga.o
board/astro/mcf5373l/astro.h deleted +0 -44
44 lines not on this page · raw message
board/astro/mcf5373l/fpga.c deleted +0 -407
407 lines not on this page · raw message
board/astro/mcf5373l/mcf5373l.c deleted +0 -201
201 lines not on this page · raw message
configs/astro_mcf5373l_defconfig deleted +0 -51
51 lines not on this page · raw message
include/configs/astro_mcf5373l.h deleted +0 -187
187 lines not on this page · raw message
Signature · 1 line
2.43.0
Quoted 1,063 lines · Tom Rini
This board is currently unmaintained. Remove it.
Signed-off-by Tom Rini <[email protected]>---
Cc: Huan Wang <[email protected]>
Cc: Angelo Dureghello <[email protected]>
Cc: Wolfgang Wegner <[email protected]>--- arch/m68k/Kconfig | 5 - arch/m68k/dts/Makefile | 1 - arch/m68k/dts/astro_mcf5373l.dts | 27 -- board/astro/mcf5373l/Kconfig | 15 -- board/astro/mcf5373l/MAINTAINERS | 6 - board/astro/mcf5373l/Makefile | 6 - board/astro/mcf5373l/astro.h | 44 ---- board/astro/mcf5373l/fpga.c | 407 ------------------------------- board/astro/mcf5373l/mcf5373l.c | 201 --------------- configs/astro_mcf5373l_defconfig | 51 ---- include/configs/astro_mcf5373l.h | 187 -------------- 11 files changed, 950 deletions(-)delete mode 100644
arch/m68k/dts/astro_mcf5373l.dtsdelete mode 100644 board/astro/mcf5373l/Kconfig delete mode 100644 board/astro/mcf5373l/MAINTAINERS delete mode 100644 board/astro/mcf5373l/Makefile delete mode 100644board/astro/mcf5373l/astro.hdelete mode 100644board/astro/mcf5373l/fpga.cdelete mode 100644board/astro/mcf5373l/mcf5373l.cdelete mode 100644 configs/astro_mcf5373l_defconfig delete mode 100644include/configs/astro_mcf5373l.harch/m68k/Kconfig +0
-5@@ -155,10 +155,6 @@ config TARGET_M5282EVB bool "Support M5282EVB" select M5282 -config TARGET_ASTRO_MCF5373L - bool "Support astro_mcf5373l" - select M5373 - config TARGET_M53017EVB bool "Support M53017EVB" select M53015@@ -183,7 +179,6 @@ config TARGET_STMARK2 endchoice source "board/BuS/eb_cpu5282/Kconfig" -source "board/astro/mcf5373l/Kconfig" source "board/cobra5272/Kconfig" source "board/freescale/m5208evbe/Kconfig" source "board/freescale/m5235evb/Kconfig"arch/m68k/dts/Makefile +0
-1@@ -11,7 +11,6 @@ dtb-$(CONFIG_TARGET_M5253DEMO) += M5253DEMO.dtb dtb-$(CONFIG_TARGET_M5272C3) += M5272C3.dtb dtb-$(CONFIG_TARGET_M5275EVB) += M5275EVB.dtb dtb-$(CONFIG_TARGET_M5282EVB) += M5282EVB.dtb -dtb-$(CONFIG_TARGET_ASTRO_MCF5373L) += astro_mcf5373l.dtb dtb-$(CONFIG_TARGET_M53017EVB) += M53017EVB.dtb dtb-$(CONFIG_TARGET_M5329EVB) += M5329AFEE.dtb M5329BFEE.dtb dtb-$(CONFIG_TARGET_M5373EVB) += M5373EVB.dtbarch/m68k/dts/astro_mcf5373l.dts deleted +0
-27@@ -1,27 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * Copyright (C) 2018 Angelo Dureghello <[email protected]> - */ - -/dts-v1/; -/include/ "mcf537x.dtsi" - -/ { - model = "Astro mcf5373l"; - compatible = "astro,mcf5373l"; - - chosen { - stdout-path = "serial0:115200n8"; - }; -}; - -&uart0 { - bootph-all; - status = "okay"; -}; - -&i2c0 { - clock-frequency = <80000>; - u-boot,i2c-slave-addr = <0x7f>; - status = "okay"; -};board/astro/mcf5373l/Kconfig deleted +0
-15@@ -1,15 +0,0 @@ -if TARGET_ASTRO_MCF5373L - -config SYS_CPU - default "mcf532x" - -config SYS_BOARD - default "mcf5373l" - -config SYS_VENDOR - default "astro" - -config SYS_CONFIG_NAME - default "astro_mcf5373l" - -endifboard/astro/mcf5373l/MAINTAINERS deleted +0
-6@@ -1,6 +0,0 @@ -MCF5373L BOARD -M: Wolfgang Wegner <[email protected]> -S: Maintained -F: board/astro/mcf5373l/ -F: include/configs/astro_mcf5373l.h -F: configs/astro_mcf5373l_defconfigboard/astro/mcf5373l/Makefile deleted +0
-6@@ -1,6 +0,0 @@ -# SPDX-License-Identifier: GPL-2.0+ -# -# (C) Copyright 2000-2006 -# Wolfgang Denk, DENX Software Engineering, [email protected]. - -obj-y = mcf5373l.o fpga.oboard/astro/mcf5373l/astro.h deleted +0
-44@@ -1,44 +0,0 @@ -#ifndef __ASTRO_H__ -#define __ASTRO_H__ - -/* in mcf5373l.c */ -int rs_serial_init (int port,int baud); -void astro_put_char (char ch); -int astro_is_char (void ); -int astro_get_char (void ); - -/* in fpga.c */ -int astro5373l_altera_load (void ); -int astro5373l_xilinx_load (void ); - -/* data structures used for communication (update.c) */ -typedef struct card_id { -char card_type; -char hardware_version; -char software_version; -char software_subversion;/* " ","a".."z" */ -char fpga_version_altera; -char fpga_version_xilinx; -}card_id_t ; - -typedef struct { -unsigned char mode; -unsigned char deviation; -unsigned short freq; -} __attribute__ ((packed))output_params_t ; - -typedef struct { -unsigned short satfreq; -unsigned char satdatallg; -unsigned short symbolrate; -unsigned char viterbirate; -unsigned char symbolrate_l; -output_params_t output_params; -unsigned char reserve; -unsigned char card_error; -unsigned short dummy_ts_id; -unsigned char dummy_pat_ver; -unsigned char dummy_sdt_ver; -} __attribute__ ((packed))parameters_t ; - -#endif /* __ASTRO_H__ */ board/astro/mcf5373l/fpga.c deleted +0
-407@@ -1,407 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* -* (C) Copyright 2006 -* Wolfgang Wegner, ASTRO Strobel Kommunikationssysteme GmbH, -* [email protected] -* -* based on the files by -* Heiko Schocher, DENX Software Engineering, [email protected] -* and -* Rich Ireland, Enterasys Networks, [email protected]. -* Keith Outwater, [email protected]. -*/ - -/* Altera/Xilinx FPGA configuration support for the ASTRO "URMEL" board */ - -#include <console.h> -#include <watchdog.h> -#include <altera.h> -#include <ACEX1K.h> -#include <spartan3.h> -#include <command.h> -#include <asm/immap_5329.h> -#include <asm/io.h> -#include "fpga.h" - -int altera_pre_fn (int cookie) -{ -gpio_t *gpiop = (gpio_t *)MMAP_GPIO ; -unsigned char tmp_char; -unsigned short tmp_short; - -/* first, set the required pins to GPIO function */ -/* PAR_T0IN -> GPIO */ - tmp_char =readb (&gpiop->par_timer); - tmp_char &=0xfc ; -writeb (tmp_char, &gpiop->par_timer); -/* all QSPI pins -> GPIO */ -writew (0x0000 , &gpiop->par_qspi); -/* U0RTS, U0CTS -> GPIO */ - tmp_short =__raw_readw (&gpiop->par_uart); - tmp_short &=0xfff3 ; -__raw_writew (tmp_short, &gpiop->par_uart); -/* all PWM pins -> GPIO */ -writeb (0x00 , &gpiop->par_pwm); -/* next, set data direction registers */ -writeb (0x01 , &gpiop->pddr_timer); -writeb (0x25 , &gpiop->pddr_qspi); -writeb (0x0c , &gpiop->pddr_uart); -writeb (0x04 , &gpiop->pddr_pwm); - -/* ensure other SPI peripherals are deselected */ -writeb (0x08 , &gpiop->ppd_uart); -writeb (0x38 , &gpiop->ppd_qspi); - -/* CONFIG = 0 STATUS = 0 -> FPGA in reset state */ -writeb (0xFB , &gpiop->pclrr_uart); -/* enable Altera configuration by clearing QSPI_CS2 and DT0IN */ -writeb (0xFE , &gpiop->pclrr_timer); -writeb (0xDF , &gpiop->pclrr_qspi); -return FPGA_SUCCESS ; -} - -/* Set the state of CONFIG Pin */ -int altera_config_fn (int assert_config,int flush,int cookie) -{ -gpio_t *gpiop = (gpio_t *)MMAP_GPIO ; - -if (assert_config) -writeb (0x04 , &gpiop->ppd_uart); -else -writeb (0xFB , &gpiop->pclrr_uart); -return FPGA_SUCCESS ; -} - -/* Returns the state of STATUS Pin */ -int altera_status_fn (int cookie) -{ -gpio_t *gpiop = (gpio_t *)MMAP_GPIO ; - -if (readb (&gpiop->ppd_pwm) &0x08 ) -return FPGA_FAIL ; -return FPGA_SUCCESS ; -} - -/* Returns the state of CONF_DONE Pin */ -int altera_done_fn (int cookie) -{ -gpio_t *gpiop = (gpio_t *)MMAP_GPIO ; - -if (readb (&gpiop->ppd_pwm) &0x20 ) -return FPGA_FAIL ; -return FPGA_SUCCESS ; -} - -/* -* writes the complete buffer to the FPGA -* writing the complete buffer in one function is much faster, -* then calling it for every bit -*/ -int altera_write_fn (const void *buf,size_t len,int flush,int cookie) -{ -size_t bytecount =0 ; -gpio_t *gpiop = (gpio_t *)MMAP_GPIO ; -unsigned char *data = (unsigned char *)buf; -unsigned char val =0 ; -int i; -int len_40 = len /40 ; - -while (bytecount < len) { - val = data[bytecount++]; - i =8 ; -do { -writeb (0xFB , &gpiop->pclrr_qspi); -if (val &0x01 ) -writeb (0x01 , &gpiop->ppd_qspi); -else -writeb (0xFE , &gpiop->pclrr_qspi); -writeb (0x04 , &gpiop->ppd_qspi); - val >>=1 ; - i--; - }while (i >0 ); - -if (bytecount % len_40 ==0 ) { -#if defined(CONFIG_HW_WATCHDOG ) || defined(CONFIG_WATCHDOG ) -schedule (); -#endif -#ifdef CONFIG_SYS_FPGA_PROG_FEEDBACK -putc ('.' );/* let them know we are alive */ -#endif -#ifdef CONFIG_SYS_FPGA_CHECK_CTRLC -if (ctrlc ()) -return FPGA_FAIL ; -#endif - } - } -return FPGA_SUCCESS ; -} - -/* called, when programming is aborted */ -int altera_abort_fn (int cookie) -{ -gpio_t *gpiop = (gpio_t *)MMAP_GPIO ; - -writeb (0x20 , &gpiop->ppd_qspi); -writeb (0x08 , &gpiop->ppd_uart); -return FPGA_SUCCESS ; -} - -/* called, when programming was succesful */ -int altera_post_fn (int cookie) -{ -return altera_abort_fn (cookie); -} - -/* -* Note that these are pointers to code that is in Flash. They will be -* relocated at runtime. -* FIXME: relocation not yet working for coldfire, see below! -*/ -Altera_CYC2_Passive_Serial_fns altera_fns = { - altera_pre_fn, - altera_config_fn, - altera_status_fn, - altera_done_fn, - altera_write_fn, - altera_abort_fn, - altera_post_fn -}; - -#define FPGA_COUNT 1 -Altera_desc altera_fpga[FPGA_COUNT ] = { - {Altera_CYC2, - passive_serial, -85903 , - (void *)&altera_fns, -NULL , -0 } -}; - -/* Initialize the fpga. Return 1 on success, 0 on failure. */ -int astro5373l_altera_load (void ) -{ -int i; - -for (i =0 ; i <FPGA_COUNT ; i++) { -/* -* I did not yet manage to get relocation work properly, -* so set stuff here instead of static initialisation: -*/ - altera_fns.pre = altera_pre_fn; - altera_fns.config = altera_config_fn; - altera_fns.status = altera_status_fn; - altera_fns.done = altera_done_fn; - altera_fns.write = altera_write_fn; - altera_fns.abort = altera_abort_fn; - altera_fns.post = altera_post_fn; - altera_fpga[i].iface_fns = (void *)&altera_fns; -fpga_add (fpga_altera, &altera_fpga[i]); - } -return 1 ; -} - -/* Set the FPGA's PROG_B line to the specified level */ -int xilinx_pgm_config_fn (int assert,int flush,int cookie) -{ -gpio_t *gpiop = (gpio_t *)MMAP_GPIO ; - -if (assert) -writeb (0xFB , &gpiop->pclrr_uart); -else -writeb (0x04 , &gpiop->ppd_uart); -return assert; -} - -/* -* Test the state of the active-low FPGA INIT line. Return 1 on INIT -* asserted (low). -*/ -int xilinx_init_config_fn (int cookie) -{ -gpio_t *gpiop = (gpio_t *)MMAP_GPIO ; - -return (readb (&gpiop->ppd_pwm) &0x08 ) ==0 ; -} - -/* Test the state of the active-high FPGA DONE pin */ -int xilinx_done_config_fn (int cookie) -{ -gpio_t *gpiop = (gpio_t *)MMAP_GPIO ; - -return (readb (&gpiop->ppd_pwm) &0x20 ) >>5 ; -} - -/* Abort an FPGA operation */ -int xilinx_abort_config_fn (int cookie) -{ -gpio_t *gpiop = (gpio_t *)MMAP_GPIO ; -/* ensure all SPI peripherals and FPGAs are deselected */ -writeb (0x08 , &gpiop->ppd_uart); -writeb (0x01 , &gpiop->ppd_timer); -writeb (0x38 , &gpiop->ppd_qspi); -return FPGA_FAIL ; -} - -/* -* FPGA pre-configuration function. Just make sure that -* FPGA reset is asserted to keep the FPGA from starting up after -* configuration. -*/ -int xilinx_pre_config_fn (int cookie) -{ -gpio_t *gpiop = (gpio_t *)MMAP_GPIO ; -unsigned char tmp_char; -unsigned short tmp_short; - -/* first, set the required pins to GPIO function */ -/* PAR_T0IN -> GPIO */ - tmp_char =readb (&gpiop->par_timer); - tmp_char &=0xfc ; -writeb (tmp_char, &gpiop->par_timer); -/* all QSPI pins -> GPIO */ -writew (0x0000 , &gpiop->par_qspi); -/* U0RTS, U0CTS -> GPIO */ - tmp_short =__raw_readw (&gpiop->par_uart); - tmp_short &=0xfff3 ; -__raw_writew (tmp_short, &gpiop->par_uart); -/* all PWM pins -> GPIO */ -writeb (0x00 , &gpiop->par_pwm); -/* next, set data direction registers */ -writeb (0x01 , &gpiop->pddr_timer); -writeb (0x25 , &gpiop->pddr_qspi); -writeb (0x0c , &gpiop->pddr_uart); -writeb (0x04 , &gpiop->pddr_pwm); - -/* ensure other SPI peripherals are deselected */ -writeb (0x08 , &gpiop->ppd_uart); -writeb (0x38 , &gpiop->ppd_qspi); -writeb (0x01 , &gpiop->ppd_timer); - -/* CONFIG = 0, STATUS = 0 -> FPGA in reset state */ -writeb (0xFB , &gpiop->pclrr_uart); -/* enable Xilinx configuration by clearing QSPI_CS2 and U0CTS */ -writeb (0xF7 , &gpiop->pclrr_uart); -writeb (0xDF , &gpiop->pclrr_qspi); -return 0 ; -} - -/* -* FPGA post configuration function. Should perform a test if FPGA is running. -*/ -int xilinx_post_config_fn (int cookie) -{ -int rc =0 ; - -/* -* no test yet -*/ -return rc; -} - -int xilinx_clk_config_fn (int assert_clk,int flush,int cookie) -{ -gpio_t *gpiop = (gpio_t *)MMAP_GPIO ; - -if (assert_clk) -writeb (0x04 , &gpiop->ppd_qspi); -else -writeb (0xFB , &gpiop->pclrr_qspi); -return assert_clk; -} - -int xilinx_wr_config_fn (int assert_write,int flush,int cookie) -{ -gpio_t *gpiop = (gpio_t *)MMAP_GPIO ; - -if (assert_write) -writeb (0x01 , &gpiop->ppd_qspi); -else -writeb (0xFE , &gpiop->pclrr_qspi); -return assert_write; -} - -int xilinx_fastwr_config_fn (void *buf,size_t len,int flush,int cookie) -{ -size_t bytecount =0 ; -gpio_t *gpiop = (gpio_t *)MMAP_GPIO ; -unsigned char *data = (unsigned char *)buf; -unsigned char val =0 ; -int i; -int len_40 = len /40 ; - -for (bytecount =0 ; bytecount < len; bytecount++) { - val = *(data++); -for (i =8 ; i >0 ; i--) { -writeb (0xFB , &gpiop->pclrr_qspi); -if (val &0x80 ) -writeb (0x01 , &gpiop->ppd_qspi); -else -writeb (0xFE , &gpiop->pclrr_qspi); -writeb (0x04 , &gpiop->ppd_qspi); - val <<=1 ; - } -if (bytecount % len_40 ==0 ) { -#if defined(CONFIG_HW_WATCHDOG ) || defined(CONFIG_WATCHDOG ) -schedule (); -#endif -#ifdef CONFIG_SYS_FPGA_PROG_FEEDBACK -putc ('.' );/* let them know we are alive */ -#endif -#ifdef CONFIG_SYS_FPGA_CHECK_CTRLC -if (ctrlc ()) -return FPGA_FAIL ; -#endif - } - } -return FPGA_SUCCESS ; -} - -/* -* Note that these are pointers to code that is in Flash. They will be -* relocated at runtime. -* FIXME: relocation not yet working for coldfire, see below! -*/ -xilinx_spartan3_slave_serial_fns xilinx_fns = { - xilinx_pre_config_fn, - xilinx_pgm_config_fn, - xilinx_clk_config_fn, - xilinx_init_config_fn, - xilinx_done_config_fn, - xilinx_wr_config_fn, -0 , - xilinx_fastwr_config_fn -}; - -xilinx_desc xilinx_fpga[FPGA_COUNT ] = { - {xilinx_spartan3, - slave_serial, -XILINX_XC3S4000_SIZE , - (void *)&xilinx_fns, -0 , - &spartan3_op} -}; - -/* Initialize the fpga. Return 1 on success, 0 on failure. */ -int astro5373l_xilinx_load (void ) -{ -int i; - -fpga_init (); - -for (i =0 ; i <FPGA_COUNT ; i++) { -/* -* I did not yet manage to get relocation work properly, -* so set stuff here instead of static initialisation: -*/ - xilinx_fns.pre = xilinx_pre_config_fn; - xilinx_fns.pgm = xilinx_pgm_config_fn; - xilinx_fns.clk = xilinx_clk_config_fn; - xilinx_fns.init = xilinx_init_config_fn; - xilinx_fns.done = xilinx_done_config_fn; - xilinx_fns.wr = xilinx_wr_config_fn; - xilinx_fns.bwr = xilinx_fastwr_config_fn; - xilinx_fpga[i].iface_fns = (void *)&xilinx_fns; -fpga_add (fpga_xilinx, &xilinx_fpga[i]); - } -return 1 ; -}board/astro/mcf5373l/mcf5373l.c deleted +0
-201@@ -1,201 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* -* (C) Copyright 2000-2003 -* Wolfgang Denk, DENX Software Engineering, [email protected]. -* modified by Wolfgang Wegner <[email protected]> for ASTRO 5373l -*/ - -#include <config.h> -#include <init.h> -#include <serial.h> -#include <time.h> -#include <watchdog.h> -#include <command.h> -#include <asm/global_data.h> -#include <asm/m5329.h> -#include <asm/immap_5329.h> -#include <asm/io.h> -#include <linux/delay.h> - -/* needed for astro bus: */ -#include <asm/uart.h> -#include "astro.h" - -DECLARE_GLOBAL_DATA_PTR ; -extern void uart_port_conf (void ); - -int checkboard (void ) -{ -puts ("Board: " ); -puts ("ASTRO MCF5373L (Urmel) Board\n" ); -return 0 ; -} - -int dram_init (void ) -{ -#if !defined(CONFIG_MONITOR_IS_IN_RAM ) -sdram_t *sdp = (sdram_t *)(MMAP_SDRAM ); - -/* -* GPIO configuration for bus should be set correctly from reset, -* so we do not care! First, set up address space: at this point, -* we should be running from internal SRAM; -* so use CFG_SYS_SDRAM_BASE as the base address for SDRAM, -* and do not care where it is -*/ -__raw_writel ((CFG_SYS_SDRAM_BASE &0xFFF00000 ) |0x00000018 , - &sdp->cs0); -__raw_writel ((CFG_SYS_SDRAM_BASE &0xFFF00000 ) |0x00000000 , - &sdp->cs1); -/* -* I am not sure from the data sheet, but it seems burst length -* has to be 8 for the 16 bit data bus we use; -* so these values are for BL = 8 -*/ -__raw_writel (0x33211530 , &sdp->cfg1); -__raw_writel (0x56570000 , &sdp->cfg2); -/* send PrechargeALL, REF and IREF remain cleared! */ -__raw_writel (0xE1462C02 , &sdp->ctrl); -udelay (1 ); -/* refresh SDRAM twice */ -__raw_writel (0xE1462C04 , &sdp->ctrl); -udelay (1 ); -__raw_writel (0xE1462C04 , &sdp->ctrl); -/* init MR */ -__raw_writel (0x008D0000 , &sdp->mode); -/* initialize EMR */ -__raw_writel (0x80010000 , &sdp->mode); -/* wait until DLL is locked */ -udelay (1 ); -/* -* enable automatic refresh, lock mode register, -* clear iref and ipall -*/ -__raw_writel (0x71462C00 , &sdp->ctrl); -/* Dummy write to start SDRAM */ -writel (0 ,CFG_SYS_SDRAM_BASE ); -#endif - -/* -* for get_ram_size() to work, both CS areas have to be -* configured, i.e. CS1 has to be explicitely disabled, else -* probing for memory will cause the SDRAM bus to hang! -* (Do not rely on the SDCS register(s) being set to 0x00000000 -* during reset as stated in the data sheet.) -*/ - gd->ram_size =get_ram_size ((long *)CFG_SYS_SDRAM_BASE , -0x80000000 -CFG_SYS_SDRAM_BASE ); - -return 0 ; -} - -#define UART_BASE MMAP_UART0 -int rs_serial_init (int port,int baud) -{ -uart_t *uart; -u32 counter; - -switch (port) { -case 0 : - uart = (uart_t *)(MMAP_UART0 ); -break ; -case 1 : - uart = (uart_t *)(MMAP_UART1 ); -break ; -case 2 : - uart = (uart_t *)(MMAP_UART2 ); -break ; -default : - uart = (uart_t *)(MMAP_UART0 ); - } - -uart_port_conf (); - -/* write to SICR: SIM2 = uart mode,dcd does not affect rx */ -writeb (UART_UCR_RESET_RX , &uart->ucr); -writeb (UART_UCR_RESET_TX , &uart->ucr); -writeb (UART_UCR_RESET_ERROR , &uart->ucr); -writeb (UART_UCR_RESET_MR , &uart->ucr); - __asm__ ("nop" ); - -writeb (0 , &uart->uimr); - -/* write to CSR: RX/TX baud rate from timers */ -writeb (UART_UCSR_RCS_SYS_CLK |UART_UCSR_TCS_SYS_CLK , &uart->ucsr); - -writeb (UART_UMR_BC_8 |UART_UMR_PM_NONE , &uart->umr); -writeb (UART_UMR_SB_STOP_BITS_1 , &uart->umr); - -/* Setting up BaudRate */ - counter = (u32) (gd->bus_clk / (baud)); - counter >>=5 ; - -/* write to CTUR: divide counter upper byte */ -writeb ((u8) ((counter &0xff00 ) >>8 ), &uart->ubg1); -/* write to CTLR: divide counter lower byte */ -writeb ((u8) (counter &0x00ff ), &uart->ubg2); - -writeb (UART_UCR_RX_ENABLED |UART_UCR_TX_ENABLED , &uart->ucr); - -return 0 ; -} - -void astro_put_char (char ch) -{ -uart_t *uart; -unsigned long timer; - - uart = (uart_t *)(MMAP_UART0 ); -/* -* Wait for last character to go. Timeout of 6ms should -* be enough for our lowest baud rate of 2400. -*/ - timer =get_timer (0 ); -while (get_timer (timer) <6 ) { -if (readb (&uart->usr) &UART_USR_TXRDY ) -break ; - } -writeb (ch, &uart->utb); - -return ; -} - -int astro_is_char (void ) -{ -uart_t *uart; - - uart = (uart_t *)(MMAP_UART0 ); -return readb (&uart->usr) &UART_USR_RXRDY ; -} - -int astro_get_char (void ) -{ -uart_t *uart; - - uart = (uart_t *)(MMAP_UART0 ); -while (!(readb (&uart->usr) &UART_USR_RXRDY )) ; -return readb (&uart->urb); -} - -int misc_init_r (void ) -{ -int retval =0 ; - -puts ("Configure Xilinx FPGA..." ); - retval =astro5373l_xilinx_load (); -if (!retval) { -puts ("failed!\n" ); -return retval; - } -puts ("done\n" ); - -puts ("Configure Altera FPGA..." ); - retval =astro5373l_altera_load (); -if (!retval) { -puts ("failed!\n" ); -return retval; - } -puts ("done\n" ); - -return retval; -}configs/astro_mcf5373l_defconfig deleted +0
-51@@ -1,51 +0,0 @@ -CONFIG_M68K=y -CONFIG_TEXT_BASE=0x00000000 -CONFIG_SYS_MALLOC_LEN=0x20000 -CONFIG_ENV_SIZE=0x8000 -CONFIG_ENV_SECT_SIZE=0x8000 -CONFIG_DEFAULT_DEVICE_TREE="astro_mcf5373l" -CONFIG_SYS_MONITOR_LEN=262144 -CONFIG_SYS_LOAD_ADDR=0x20000 -CONFIG_ENV_ADDR=0x1FF8000 -CONFIG_TARGET_ASTRO_MCF5373L=y -CONFIG_SYS_MONITOR_BASE=0x00000400 -CONFIG_BOOTDELAY=1 -CONFIG_USE_BOOTARGS=y -CONFIG_BOOTARGS=" console=ttyS2,115200 rootfstype=romfs loaderversion=$loaderversion" -CONFIG_USE_BOOTCOMMAND=y -CONFIG_BOOTCOMMAND="protect off 0x80000 0x1ffffff;run env_check;run xilinxload&&run alteraload&&bootm 0x80000;update;reset" -CONFIG_SYS_PBSIZE=281 -# CONFIG_DISPLAY_BOARDINFO is not set -CONFIG_MISC_INIT_R=y -CONFIG_SYS_MALLOC_BOOTPARAMS=y -CONFIG_HUSH_PARSER=y -# CONFIG_AUTO_COMPLETE is not set -CONFIG_SYS_PROMPT="URMEL > " -CONFIG_CMD_IMLS=y -CONFIG_CMD_FPGA_LOADMK=y -CONFIG_CMD_I2C=y -# CONFIG_CMD_SETEXPR is not set -CONFIG_CMD_CACHE=y -CONFIG_CMD_JFFS2=y -CONFIG_NO_NET=y -CONFIG_FPGA_ALTERA=y -CONFIG_FPGA_CYCLON2=y -CONFIG_FPGA_XILINX=y -CONFIG_FPGA_SPARTAN3=y -CONFIG_SYS_FPGA_PROG_FEEDBACK=y -CONFIG_DM_I2C=y -CONFIG_SYS_I2C_FSL=y -CONFIG_MTD=y -CONFIG_MTD_NOR_FLASH=y -CONFIG_FLASH_CFI_DRIVER=y -CONFIG_FLASH_SHOW_PROGRESS=0 -CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y -CONFIG_SYS_FLASH_PROTECTION=y -CONFIG_SYS_FLASH_CFI=y -CONFIG_SYS_MAX_FLASH_SECT=259 -CONFIG_DM_RTC=y -CONFIG_MCFRTC=y -CONFIG_SYS_MCFRTC_BASE=0xFC0A8000 -CONFIG_MCFUART=y -CONFIG_WDT=y -CONFIG_WDT_MCF=yinclude/configs/astro_mcf5373l.h deleted +0
-187@@ -1,187 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* -* Configuration settings for the Sentec Cobra Board. -* -* (C) Copyright 2003 Josef Baumgartner <[email protected]> -*/ - -/* -* configuration for ASTRO "Urmel" board. -* Originating from Cobra5272 configuration, messed up by -* Wolfgang Wegner <[email protected]> -* Please do not bother the original author with bug reports -* concerning this file. -*/ - -#ifndef _CONFIG_ASTRO_MCF5373L_H -#define _CONFIG_ASTRO_MCF5373L_H - -#include <linux/stringify.h> - -/* -* set the card type to actually compile for; either of -* the possibilities listed below has to be used! -*/ -#define ASTRO_V532 1 - -#if ASTRO_V532 -#define ASTRO_ID 0xF8 -#elif ASTRO_V512 -#define ASTRO_ID 0xFA -#elif ASTRO_TWIN7S2 -#define ASTRO_ID 0xF9 -#elif ASTRO_V912 -#define ASTRO_ID 0xFC -#elif ASTRO_COFDMDUOS2 -#define ASTRO_ID 0xFB -#else -#error No card type defined! -#endif - -/* I2C */ - -/* -* Defines processor clock - important for correct timings concerning serial -* interface etc. -*/ - -#define CFG_SYS_CLK 80000000 -#define CFG_SYS_CPU_CLK (CFG_SYS_CLK * 3) -#define CFG_SYS_SDRAM_SIZE 32/* SDRAM size in MB */ - -/* -* Define baudrate for UART1 (console output, tftp, ...) -* default value of CONFIG_BAUDRATE for Sentec board: 19200 baud -* CFG_SYS_BAUDRATE_TABLE defines values that can be selected -* in u-boot command interface -*/ - -#define CFG_SYS_UART_PORT (2) -#define CFG_SYS_UART2_ALT3_GPIO - -/* here we put our FPGA configuration... */ - -/* Define user parameters that have to be customized most likely */ - -/* AUTOBOOT settings - booting images automatically by u-boot after power on */ - -/* -* The following settings will be contained in the environment block ; if you -* want to use a neutral environment all those settings can be manually set in -* u-boot: 'set' command -*/ - -#define CFG_EXTRA_ENV_SETTINGS \ - "loaderversion=11\0" \ - "card_id="__stringify(ASTRO_ID)"\0" \ - "alterafile=0\0" \ - "xilinxfile=0\0" \ - "xilinxload=imxtract 0x540000 $xilinxfile 0x41000000&&"\ - "fpga load 0 0x41000000 $filesize\0" \ - "alteraload=imxtract 0x6c0000 $alterafile 0x41000000&&"\ - "fpga load 1 0x41000000 $filesize\0" \ - "env_default=1\0" \ - "env_check=if test $env_default -eq 1;"\ - " then setenv env_default 0;saveenv;fi\0" - -/* -* "update" is a non-standard command that has to be supplied -* by external update.c; This is not included in mainline because -* it needs non-blocking CFI routines. -*/ - -#define CFG_SYS_FPGA_WAIT 1000 - -/* End of user parameters to be customized */ - -/* Defines memory range for test */ - -/* -* Low Level Configuration Settings -* (address mappings, register initial values, etc.) -* You should know what you are doing if you make changes here. -*/ - -/* Base register address */ - -#define CFG_SYS_MBAR 0xFC000000/* Register Base Addrs */ - -/* System Conf. Reg. & System Protection Reg. */ - -#define CFG_SYS_SCR 0x0003; -#define CFG_SYS_SPR 0xffff; - -/* -* Definitions for initial stack pointer and data area (in internal SRAM) -*/ -#define CFG_SYS_INIT_RAM_ADDR 0x80000000 -#define CFG_SYS_INIT_RAM_SIZE 0x8000 -#define CFG_SYS_INIT_RAM_CTRL 0x221 - -/* -* Start addresses for the final memory configuration -* (Set up by the startup code) -* for MCF5373, the allowable range is 0x40000000 to 0x7FF00000 -*/ -#define CFG_SYS_SDRAM_BASE 0x40000000 - -/* -* Chipselect bank definitions -* -* CS0 - Flash 32MB (first 16MB) -* CS1 - Flash 32MB (second half) -* CS2 - FPGA -* CS3 - FPGA -* CS4 - unused -* CS5 - unused -*/ -#define CFG_SYS_CS0_BASE 0 -#define CFG_SYS_CS0_MASK 0x00ff0001 -#define CFG_SYS_CS0_CTRL 0x00001fc0 - -#define CFG_SYS_CS1_BASE 0x01000000 -#define CFG_SYS_CS1_MASK 0x00ff0001 -#define CFG_SYS_CS1_CTRL 0x00001fc0 - -#define CFG_SYS_CS2_BASE 0x20000000 -#define CFG_SYS_CS2_MASK 0x00ff0001 -#define CFG_SYS_CS2_CTRL 0x0000fec0 - -#define CFG_SYS_CS3_BASE 0x21000000 -#define CFG_SYS_CS3_MASK 0x00ff0001 -#define CFG_SYS_CS3_CTRL 0x0000fec0 - -#define CFG_SYS_FLASH_BASE 0x00000000 - -/* Reserve 256 kB for Monitor */ - -/* -* For booting Linux, the board info and command line data -* have to be in the first 8 MB of memory, since this is -* the maximum mapped by the Linux kernel during initialization ?? -*/ -#define CFG_SYS_BOOTMAPSZ (CFG_SYS_SDRAM_BASE + \ - (CFG_SYS_SDRAM_SIZE << 20)) - -/* FLASH organization */ - -#define CFG_SYS_FLASH_SIZE 0x2000000 - -#define LDS_BOARD_TEXT \ - . = DEFINED(env_offset) ? env_offset : .; \ - env/embedded.o(.text*) - -/* Cache Configuration */ - -#define ICACHE_STATUS (CFG_SYS_INIT_RAM_ADDR + \ - CFG_SYS_INIT_RAM_SIZE - 8) -#define DCACHE_STATUS (CFG_SYS_INIT_RAM_ADDR + \ - CFG_SYS_INIT_RAM_SIZE - 4) -#define CFG_SYS_ICACHE_INV (CF_CACR_CINVA) -#define CFG_SYS_CACHE_ACR0 (CFG_SYS_SDRAM_BASE | \ - CF_ADDRMASK(CFG_SYS_SDRAM_SIZE) | \ - CF_ACR_EN | CF_ACR_SM_ALL) -#define CFG_SYS_CACHE_ICACR (CF_CACR_EC | CF_CACR_CINVA | \ - CF_CACR_DCM_P) - -#endif /* _CONFIG_ASTRO_MCF5373L_H */
Quoted 3 lines · Tom Rini
This board is currently unmaintained. Remove it.
Applied to u-boot/next, thanks!
[1/1] m68k: Remove astro_mcf5373l board
commit: e5d4733c2e1937eb7b622771bfea9f1fda0425c6
Signature · 1 line
Tom