Skip to contentSkip to conversation

xen/arm: add i.MX8M platform and UART support

PATCH Superseded Wig Cheng 2 participants 12 messages Aug 18 Arm i.MX and Layerscape

v2 of 4 Superseded Latest is v4 →

lore
Share & tools
lore

Wig Cheng

author
#0 lore raw

v2 cover xen/arm: add i.MX8M platform and UART support

Following Michal Orzel's review of v1, this series adds Xen support for the NXP i.MX8M family (i.MX8MP / MQ / MM / MN). It provides the console UART driver, its early printk, the platform glue (SiP SMC whitelist for the calls the dom0 kernel issues to TF-A), and a MAINTAINERS entry.

Tested on i.MX8MP (4x Cortex-A53, GICv3) with the vendor kernel 6.18:
dom0 boots to login on the hypervisor console, and a domU starts with a PV disk and virtio devices running a full Wayland distro.

Notes for reviewers:

- Unlike i.MX8MQ, the i.MX8MP device tree uses the GIC as the root interrupt controller (interrupt-parent = <&gic>), so no device-tree workaround is needed and power domains keep working.

- The i.MX8M family has no SMMU, so device passthrough relies on the 1:1 direct-mapped hardware domain.

- The SiP SMC whitelist forwards only the specific subfunctions the dom0 kernel issues, extracted from the vendor kernel call sites. DDR DVFS is left at service level because its reg1 is a frequency setpoint rather than a fixed subfunction id. No call was denied at runtime.

Changes since v1:

Patch 1 (UART driver):
- Documentation narrowed to the i.MX8M family (dropped i.MX6/7).
- Relicensed the new files as GPL-2.0-only.
- Dropped the stale file-path lines from the file headers.
- Renamed the header guard to ASM_IMX_UART_H.
- Removed unused register/bit macros; header is now asm-safe (BIT(n, U)).
- Also clear UCR1_TXMPTYEN on init; documented that the console is driven entirely through UCR1.

Patch 2 (early printk):
- bne -> b.ne.

Patch 3 (platform):
- Build the SiP function IDs with ARM_SMCCC_CALL_VAL (IMX_SIP_FID), matching the i.MX8QM platform.
- Whitelist per subfunction (GPC, SRC, NoC) instead of whole services; DDR DVFS and SoC info kept at service level with a comment on why.
- Dropped the BBSM call, which is not issued on i.MX8M.
- Fixed the misleading "secure RTC" comment and a stray space.

Patch 4 (new):
- MAINTAINERS entry, as a separate patch.

v1: https://lore.kernel.org/xen-devel/[email protected]/

Wig Cheng (4):
xen/char: add classic i.MX UART driver
xen/arm64: add early printk for the classic i.MX UART xen/arm: add i.MX8M platform support
MAINTAINERS: add myself as reviewer of i.MX8M related patches

 MAINTAINERS                           |   7 +
 xen/arch/arm/Kconfig.debug            |  12 ++
 xen/arch/arm/arm64/debug-imx-uart.inc |  37 +++++
 xen/arch/arm/include/asm/imx-uart.h   |  57 +++++++
 xen/arch/arm/platforms/Makefile       |   1 +
 xen/arch/arm/platforms/imx8m.c        | 152 +++++++++++++++++
 xen/drivers/char/Kconfig              |   8 +
 xen/drivers/char/Makefile             |   1 +
 xen/drivers/char/imx-uart.c           | 226 ++++++++++++++++++++++++++
 9 files changed, 501 insertions(+)
 create mode 100644 xen/arch/arm/arm64/debug-imx-uart.inc
 create mode 100644 xen/arch/arm/include/asm/imx-uart.h
 create mode 100644 xen/arch/arm/platforms/imx8m.c
 create mode 100644 xen/drivers/char/imx-uart.c
Signature · 1 line
2.43.0
author
#1 lore raw

PATCH v2 1/4 xen/char: add classic i.MX UART driver

Add a console driver for the classic i.MX UART IP ("fsl,imx6q-uart" compatible), used as the console UART on the i.MX8M family. Baudrate and pin configuration are inherited from the bootloader; the driver only enables the transmitter/receiver and wires up the RX/TX interrupts, mirroring the existing imx-lpuart driver.

The i.MX8M family's UART IP differs from the LPUART used on i.MX8QM/8QXP, so a separate driver is needed.

---
 xen/arch/arm/include/asm/imx-uart.h |  57 +++++++
 xen/drivers/char/Kconfig            |   8 +
 xen/drivers/char/Makefile           |   1 +
 xen/drivers/char/imx-uart.c         | 226 ++++++++++++++++++++++++++++
 4 files changed, 292 insertions(+)
 create mode 100644 xen/arch/arm/include/asm/imx-uart.h
 create mode 100644 xen/drivers/char/imx-uart.c
xen/arch/arm/include/asm/imx-uart.h new file +57 -0
new file mode 100644
index 0000000000..a3892020e6
@@ -0,0 +1,57 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Register definitions for the classic i.MX UART IP
+ * ("fsl,imx6q-uart" compatible), used as the console UART on the
+ * i.MX8M family.
+ *
+ * Register layout taken from Linux drivers/tty/serial/imx.c.
+ *
+ * Copyright 2026 Open-EP (E-Paper) Community
+ */
+
+#ifndef ASM_IMX_UART_H
+#define ASM_IMX_UART_H
+
+#include <xen/const.h>
+
+#define URXD0           0x00   /* Receiver Register */
+#define URTX0           0x40   /* Transmitter Register */
+#define UCR1            0x80   /* Control Register 1 */
+#define UCR2            0x84   /* Control Register 2 */
+#define USR1            0x94   /* Status Register 1 */
+#define USR2            0x98   /* Status Register 2 */
+#define UTS             0xb4   /* Test Register */
+
+#define URXD_RX_DATA    0xff
+
+#define UCR1_UARTEN     BIT(0, U)   /* UART enable */
+#define UCR1_ATDMAEN    BIT(2, U)   /* Aging DMA timer enable */
+#define UCR1_TXDMAEN    BIT(3, U)   /* Transmitter ready DMA enable */
+#define UCR1_TXMPTYEN   BIT(6, U)   /* Transmitter empty interrupt enable */
+#define UCR1_RXDMAEN    BIT(8, U)   /* Receiver ready DMA enable */
+#define UCR1_RRDYEN     BIT(9, U)   /* Receiver ready interrupt enable */
+#define UCR1_TRDYEN     BIT(13, U)  /* Transmitter ready interrupt enable */
+
+#define UCR2_SRST       BIT(0, U)   /* 0 = issue software reset */
+#define UCR2_RXEN       BIT(1, U)   /* Receiver enable */
+#define UCR2_TXEN       BIT(2, U)   /* Transmitter enable */
+
+#define USR1_TRDY       BIT(13, U)  /* Transmitter ready */
+
+#define USR2_RDR        BIT(0, U)   /* Receive data ready */
+#define USR2_ORE        BIT(1, U)   /* Overrun error */
+
+#define UTS_TXFULL      BIT(4, U)   /* TX FIFO full */
+#define UTS_RXEMPTY     BIT(5, U)   /* RX FIFO empty */
+#define UTS_TXEMPTY     BIT(6, U)   /* TX FIFO empty */
+
+#endif /* ASM_IMX_UART_H */
+
+/*
+ * Local variables:
+ * mode: C
+ * c-file-style: "BSD"
+ * c-basic-offset: 4
+ * indent-tabs-mode: nil
+ * End:
+ */
xen/drivers/char/Kconfig +8 -0
index 8e49a52c73..f237c0220d 100644
@@ -30,6 +30,14 @@ config HAS_IMX_LPUART
 	help
 	  This selects the i.MX LPUART. If you have i.MX8QM based board, say Y.
 
+config HAS_IMX_UART
+	bool "i.MX UART driver"
+	default y
+	depends on ARM_64
+	help
+	  This selects the classic i.MX UART. If you have an i.MX8M family
+	  based board, say Y.
+
 config HAS_MVEBU
 	bool "Marvell MVEBU UART driver"
 	default y
xen/drivers/char/Makefile +1 -0
index 8cbbffdca8..039f566926 100644
@@ -10,6 +10,7 @@ obj-$(CONFIG_HAS_SCIF) += scif-uart.o
 obj-$(CONFIG_HAS_EHCI) += ehci-dbgp.o
 obj-$(CONFIG_XHCI) += xhci-dbc.o
 obj-$(CONFIG_HAS_IMX_LPUART) += imx-lpuart.o
+obj-$(CONFIG_HAS_IMX_UART) += imx-uart.o
 obj-$(CONFIG_HAS_LINFLEX) += linflex-uart.o
 obj-$(CONFIG_GENERIC_UART_INIT) += uart-init.o
 obj-y += serial.o
xen/drivers/char/imx-uart.c new file +226 -0

226 lines not on this page · raw message

Signature · 1 line
2.43.0
#2 lore raw

Re: [PATCH v2 1/4] xen/char: add classic i.MX UART driver

Quoted 9 lines · Wig Cheng

Add a console driver for the classic i.MX UART IP ("fsl,imx6q-uart" compatible), used as the console UART on the i.MX8M family. Baudrate and pin configuration are inherited from the bootloader; the driver only enables the transmitter/receiver and wires up the RX/TX interrupts, mirroring the existing imx-lpuart driver.

The i.MX8M family's UART IP differs from the LPUART used on i.MX8QM/8QXP, so a separate driver is needed.

Quoted 6 lines
---
 xen/arch/arm/include/asm/imx-uart.h |  57 +++++++
 xen/drivers/char/Kconfig            |   8 +
 xen/drivers/char/Makefile           |   1 +
 xen/drivers/char/imx-uart.c         | 226 ++++++++++++++++++++++++++++

You should add an entry to the MAINTAINERS file for imx-uart.c so that it falls down under ARM maintainership. Your last patch makes you a reviewer but we still need to be maintainers of it. See how it was done for IMX8QM.

Quoted 132 lines
 4 files changed, 292 insertions(+)
 create mode 100644 xen/arch/arm/include/asm/imx-uart.h
 create mode 100644 xen/drivers/char/imx-uart.c
xen/arch/arm/include/asm/imx-uart.h new file +57 -0
new file mode 100644
index 0000000000..a3892020e6
@@ -0,0 +1,57 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Register definitions for the classic i.MX UART IP
+ * ("fsl,imx6q-uart" compatible), used as the console UART on the
+ * i.MX8M family.
+ *
+ * Register layout taken from Linux drivers/tty/serial/imx.c.
+ *
+ * Copyright 2026 Open-EP (E-Paper) Community
+ */
+
+#ifndef ASM_IMX_UART_H
+#define ASM_IMX_UART_H
+
+#include <xen/const.h>
+
+#define URXD0           0x00   /* Receiver Register */
+#define URTX0           0x40   /* Transmitter Register */
+#define UCR1            0x80   /* Control Register 1 */
+#define UCR2            0x84   /* Control Register 2 */
+#define USR1            0x94   /* Status Register 1 */
+#define USR2            0x98   /* Status Register 2 */
+#define UTS             0xb4   /* Test Register */
+
+#define URXD_RX_DATA    0xff
+
+#define UCR1_UARTEN     BIT(0, U)   /* UART enable */
+#define UCR1_ATDMAEN    BIT(2, U)   /* Aging DMA timer enable */
+#define UCR1_TXDMAEN    BIT(3, U)   /* Transmitter ready DMA enable */
+#define UCR1_TXMPTYEN   BIT(6, U)   /* Transmitter empty interrupt enable */
+#define UCR1_RXDMAEN    BIT(8, U)   /* Receiver ready DMA enable */
+#define UCR1_RRDYEN     BIT(9, U)   /* Receiver ready interrupt enable */
+#define UCR1_TRDYEN     BIT(13, U)  /* Transmitter ready interrupt enable */
+
+#define UCR2_SRST       BIT(0, U)   /* 0 = issue software reset */
+#define UCR2_RXEN       BIT(1, U)   /* Receiver enable */
+#define UCR2_TXEN       BIT(2, U)   /* Transmitter enable */
+
+#define USR1_TRDY       BIT(13, U)  /* Transmitter ready */
+
+#define USR2_RDR        BIT(0, U)   /* Receive data ready */
+#define USR2_ORE        BIT(1, U)   /* Overrun error */
+
+#define UTS_TXFULL      BIT(4, U)   /* TX FIFO full */
+#define UTS_RXEMPTY     BIT(5, U)   /* RX FIFO empty */
+#define UTS_TXEMPTY     BIT(6, U)   /* TX FIFO empty */
+
+#endif /* ASM_IMX_UART_H */
+
+/*
+ * Local variables:
+ * mode: C
+ * c-file-style: "BSD"
+ * c-basic-offset: 4
+ * indent-tabs-mode: nil
+ * End:
+ */
xen/drivers/char/Kconfig +8 -0
index 8e49a52c73..f237c0220d 100644
@@ -30,6 +30,14 @@ config HAS_IMX_LPUART
 	help
 	  This selects the i.MX LPUART. If you have i.MX8QM based board, say Y.
 
+config HAS_IMX_UART
+	bool "i.MX UART driver"
+	default y
+	depends on ARM_64
+	help
+	  This selects the classic i.MX UART. If you have an i.MX8M family
+	  based board, say Y.
+
 config HAS_MVEBU
 	bool "Marvell MVEBU UART driver"
 	default y
xen/drivers/char/Makefile +1 -0
index 8cbbffdca8..039f566926 100644
@@ -10,6 +10,7 @@ obj-$(CONFIG_HAS_SCIF) += scif-uart.o
 obj-$(CONFIG_HAS_EHCI) += ehci-dbgp.o
 obj-$(CONFIG_XHCI) += xhci-dbc.o
 obj-$(CONFIG_HAS_IMX_LPUART) += imx-lpuart.o
+obj-$(CONFIG_HAS_IMX_UART) += imx-uart.o
 obj-$(CONFIG_HAS_LINFLEX) += linflex-uart.o
 obj-$(CONFIG_GENERIC_UART_INIT) += uart-init.o
 obj-y += serial.o
xen/drivers/char/imx-uart.c new file +28 -0
new file mode 100644
index 0000000000..fd34b0cd11
@@ -0,0 +1,226 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Driver for the classic i.MX UART IP ("fsl,imx6q-uart"), used as the
+ * console UART on the i.MX8M family (e.g. i.MX8MP).
+ *
+ * Baudrate and pin configuration are inherited from the bootloader.
+ *
+ * Copyright 2026 Open-EP (E-Paper) Community
+ */
+
+#include <xen/errno.h>
+#include <xen/init.h>
+#include <xen/irq.h>
+#include <xen/mm.h>
+#include <xen/serial.h>
+#include <asm/device.h>
+#include <asm/imx-uart.h>
+#include <asm/io.h>
+
+#define imx_uart_read(uart, off)       readl((uart)->regs + (off))
+#define imx_uart_write(uart, off, val) writel((val), (uart)->regs + (off))
+
+static struct imx_uart {
+    uint32_t irq;
+    char __iomem *regs;
+    struct irqaction irqaction;
+    struct vuart_info vuart;
+} imx8m_com;

xen/drivers/char/imx-uart.c line 38

Quoted 10 lines
xen/drivers/char/imx-uart.c new file +10 -0
+
+static void imx_uart_interrupt(int irq, void *data)
+{
+    struct serial_port *port = data;
+    struct imx_uart *uart = port->uart;
+
+    if ( imx_uart_read(uart, USR2) & USR2_RDR )
+        serial_rx_interrupt(port);
+
+    if ( imx_uart_read(uart, USR1) & USR1_TRDY )

Looking at Linux's imx.c you should clear TRDY if TRDEN is not enabled to prevent RX interrupt entering serial_tx_interrupt as TRDY is a raw status register.

Quoted 26 lines
xen/drivers/char/imx-uart.c new file +26 -0
+        serial_tx_interrupt(port);
+}
+
+static void __init imx_uart_init_preirq(struct serial_port *port)
+{
+    struct imx_uart *uart = port->uart;
+    uint32_t ucr1, ucr2;
+
+    /*
+     * Reuse the bootloader settings; only enable the UART and both
+     * directions.  The console uses UCR1 interrupts (RRDYEN/TRDYEN)
+     * exclusively, so just clear UCR1's interrupt and DMA enables.
+     */
+    ucr1 = imx_uart_read(uart, UCR1);
+    ucr1 &= ~(UCR1_RRDYEN | UCR1_TRDYEN | UCR1_TXMPTYEN | UCR1_RXDMAEN |
+              UCR1_TXDMAEN | UCR1_ATDMAEN);
+    ucr1 |= UCR1_UARTEN;
+    imx_uart_write(uart, UCR1, ucr1);
+
+    ucr2 = imx_uart_read(uart, UCR2);
+    ucr2 |= UCR2_SRST | UCR2_RXEN | UCR2_TXEN;
+    imx_uart_write(uart, UCR2, ucr2);
+}
+
+static void __init imx_uart_init_postirq(struct serial_port *port)
+{

xen/drivers/char/imx-uart.c line 74

Quoted 10 lines
xen/drivers/char/imx-uart.c new file +10 -0
+    struct imx_uart *uart = port->uart;
+    uint32_t ucr1;
+
+    uart->irqaction.handler = imx_uart_interrupt;
+    uart->irqaction.name = "imx_uart";
+    uart->irqaction.dev_id = port;
+
+    if ( setup_irq(uart->irq, 0, &uart->irqaction) != 0 )
+    {
+        dprintk(XENLOG_ERR, "Failed to allocate imx_uart IRQ %d\n", uart->irq);

uart->irq is unsigned, so s/%d/%u.

~Michal

#3 lore raw

Re: [PATCH v2 1/4] xen/char: add classic i.MX UART driver

In reply to Wig Cheng
Quoted 9 lines · Wig Cheng

Add a console driver for the classic i.MX UART IP ("fsl,imx6q-uart" compatible), used as the console UART on the i.MX8M family. Baudrate and pin configuration are inherited from the bootloader; the driver only enables the transmitter/receiver and wires up the RX/TX interrupts, mirroring the existing imx-lpuart driver.

The i.MX8M family's UART IP differs from the LPUART used on i.MX8QM/8QXP, so a separate driver is needed.

Quoted 6 lines
---
 xen/arch/arm/include/asm/imx-uart.h |  57 +++++++
 xen/drivers/char/Kconfig            |   8 +
 xen/drivers/char/Makefile           |   1 +
 xen/drivers/char/imx-uart.c         | 226 ++++++++++++++++++++++++++++

You should add an entry to the MAINTAINERS file for imx-uart.c so that it falls down under ARM maintainership. Your last patch makes you a reviewer but we still need to be maintainers of it. See how it was done for IMX8QM.

Quoted 132 lines
 4 files changed, 292 insertions(+)
 create mode 100644 xen/arch/arm/include/asm/imx-uart.h
 create mode 100644 xen/drivers/char/imx-uart.c
xen/arch/arm/include/asm/imx-uart.h new file +57 -0
new file mode 100644
index 0000000000..a3892020e6
@@ -0,0 +1,57 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Register definitions for the classic i.MX UART IP
+ * ("fsl,imx6q-uart" compatible), used as the console UART on the
+ * i.MX8M family.
+ *
+ * Register layout taken from Linux drivers/tty/serial/imx.c.
+ *
+ * Copyright 2026 Open-EP (E-Paper) Community
+ */
+
+#ifndef ASM_IMX_UART_H
+#define ASM_IMX_UART_H
+
+#include <xen/const.h>
+
+#define URXD0           0x00   /* Receiver Register */
+#define URTX0           0x40   /* Transmitter Register */
+#define UCR1            0x80   /* Control Register 1 */
+#define UCR2            0x84   /* Control Register 2 */
+#define USR1            0x94   /* Status Register 1 */
+#define USR2            0x98   /* Status Register 2 */
+#define UTS             0xb4   /* Test Register */
+
+#define URXD_RX_DATA    0xff
+
+#define UCR1_UARTEN     BIT(0, U)   /* UART enable */
+#define UCR1_ATDMAEN    BIT(2, U)   /* Aging DMA timer enable */
+#define UCR1_TXDMAEN    BIT(3, U)   /* Transmitter ready DMA enable */
+#define UCR1_TXMPTYEN   BIT(6, U)   /* Transmitter empty interrupt enable */
+#define UCR1_RXDMAEN    BIT(8, U)   /* Receiver ready DMA enable */
+#define UCR1_RRDYEN     BIT(9, U)   /* Receiver ready interrupt enable */
+#define UCR1_TRDYEN     BIT(13, U)  /* Transmitter ready interrupt enable */
+
+#define UCR2_SRST       BIT(0, U)   /* 0 = issue software reset */
+#define UCR2_RXEN       BIT(1, U)   /* Receiver enable */
+#define UCR2_TXEN       BIT(2, U)   /* Transmitter enable */
+
+#define USR1_TRDY       BIT(13, U)  /* Transmitter ready */
+
+#define USR2_RDR        BIT(0, U)   /* Receive data ready */
+#define USR2_ORE        BIT(1, U)   /* Overrun error */
+
+#define UTS_TXFULL      BIT(4, U)   /* TX FIFO full */
+#define UTS_RXEMPTY     BIT(5, U)   /* RX FIFO empty */
+#define UTS_TXEMPTY     BIT(6, U)   /* TX FIFO empty */
+
+#endif /* ASM_IMX_UART_H */
+
+/*
+ * Local variables:
+ * mode: C
+ * c-file-style: "BSD"
+ * c-basic-offset: 4
+ * indent-tabs-mode: nil
+ * End:
+ */
xen/drivers/char/Kconfig +8 -0
index 8e49a52c73..f237c0220d 100644
@@ -30,6 +30,14 @@ config HAS_IMX_LPUART
 	help
 	  This selects the i.MX LPUART. If you have i.MX8QM based board, say Y.
 
+config HAS_IMX_UART
+	bool "i.MX UART driver"
+	default y
+	depends on ARM_64
+	help
+	  This selects the classic i.MX UART. If you have an i.MX8M family
+	  based board, say Y.
+
 config HAS_MVEBU
 	bool "Marvell MVEBU UART driver"
 	default y
xen/drivers/char/Makefile +1 -0
index 8cbbffdca8..039f566926 100644
@@ -10,6 +10,7 @@ obj-$(CONFIG_HAS_SCIF) += scif-uart.o
 obj-$(CONFIG_HAS_EHCI) += ehci-dbgp.o
 obj-$(CONFIG_XHCI) += xhci-dbc.o
 obj-$(CONFIG_HAS_IMX_LPUART) += imx-lpuart.o
+obj-$(CONFIG_HAS_IMX_UART) += imx-uart.o
 obj-$(CONFIG_HAS_LINFLEX) += linflex-uart.o
 obj-$(CONFIG_GENERIC_UART_INIT) += uart-init.o
 obj-y += serial.o
xen/drivers/char/imx-uart.c new file +28 -0
new file mode 100644
index 0000000000..fd34b0cd11
@@ -0,0 +1,226 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Driver for the classic i.MX UART IP ("fsl,imx6q-uart"), used as the
+ * console UART on the i.MX8M family (e.g. i.MX8MP).
+ *
+ * Baudrate and pin configuration are inherited from the bootloader.
+ *
+ * Copyright 2026 Open-EP (E-Paper) Community
+ */
+
+#include <xen/errno.h>
+#include <xen/init.h>
+#include <xen/irq.h>
+#include <xen/mm.h>
+#include <xen/serial.h>
+#include <asm/device.h>
+#include <asm/imx-uart.h>
+#include <asm/io.h>
+
+#define imx_uart_read(uart, off)       readl((uart)->regs + (off))
+#define imx_uart_write(uart, off, val) writel((val), (uart)->regs + (off))
+
+static struct imx_uart {
+    uint32_t irq;
+    char __iomem *regs;
+    struct irqaction irqaction;
+    struct vuart_info vuart;
+} imx8m_com;

xen/drivers/char/imx-uart.c line 38

Quoted 10 lines
xen/drivers/char/imx-uart.c new file +10 -0
+
+static void imx_uart_interrupt(int irq, void *data)
+{
+    struct serial_port *port = data;
+    struct imx_uart *uart = port->uart;
+
+    if ( imx_uart_read(uart, USR2) & USR2_RDR )
+        serial_rx_interrupt(port);
+
+    if ( imx_uart_read(uart, USR1) & USR1_TRDY )

Looking at Linux's imx.c you should clear TRDY if TRDEN is not enabled to prevent RX interrupt entering serial_tx_interrupt as TRDY is a raw status register.

Quoted 26 lines
xen/drivers/char/imx-uart.c new file +26 -0
+        serial_tx_interrupt(port);
+}
+
+static void __init imx_uart_init_preirq(struct serial_port *port)
+{
+    struct imx_uart *uart = port->uart;
+    uint32_t ucr1, ucr2;
+
+    /*
+     * Reuse the bootloader settings; only enable the UART and both
+     * directions.  The console uses UCR1 interrupts (RRDYEN/TRDYEN)
+     * exclusively, so just clear UCR1's interrupt and DMA enables.
+     */
+    ucr1 = imx_uart_read(uart, UCR1);
+    ucr1 &= ~(UCR1_RRDYEN | UCR1_TRDYEN | UCR1_TXMPTYEN | UCR1_RXDMAEN |
+              UCR1_TXDMAEN | UCR1_ATDMAEN);
+    ucr1 |= UCR1_UARTEN;
+    imx_uart_write(uart, UCR1, ucr1);
+
+    ucr2 = imx_uart_read(uart, UCR2);
+    ucr2 |= UCR2_SRST | UCR2_RXEN | UCR2_TXEN;
+    imx_uart_write(uart, UCR2, ucr2);
+}
+
+static void __init imx_uart_init_postirq(struct serial_port *port)
+{

xen/drivers/char/imx-uart.c line 74

Quoted 10 lines
xen/drivers/char/imx-uart.c new file +10 -0
+    struct imx_uart *uart = port->uart;
+    uint32_t ucr1;
+
+    uart->irqaction.handler = imx_uart_interrupt;
+    uart->irqaction.name = "imx_uart";
+    uart->irqaction.dev_id = port;
+
+    if ( setup_irq(uart->irq, 0, &uart->irqaction) != 0 )
+    {
+        dprintk(XENLOG_ERR, "Failed to allocate imx_uart IRQ %d\n", uart->irq);

uart->irq is unsigned, so s/%d/%u.

~Michal

#4 lore raw

Re: [PATCH v2 1/4] xen/char: add classic i.MX UART driver

In reply to Wig Cheng
Quoted 9 lines · Wig Cheng

Add a console driver for the classic i.MX UART IP ("fsl,imx6q-uart" compatible), used as the console UART on the i.MX8M family. Baudrate and pin configuration are inherited from the bootloader; the driver only enables the transmitter/receiver and wires up the RX/TX interrupts, mirroring the existing imx-lpuart driver.

The i.MX8M family's UART IP differs from the LPUART used on i.MX8QM/8QXP, so a separate driver is needed.

Quoted 6 lines
---
 xen/arch/arm/include/asm/imx-uart.h |  57 +++++++
 xen/drivers/char/Kconfig            |   8 +
 xen/drivers/char/Makefile           |   1 +
 xen/drivers/char/imx-uart.c         | 226 ++++++++++++++++++++++++++++

You should add an entry to the MAINTAINERS file for imx-uart.c so that it falls down under ARM maintainership. Your last patch makes you a reviewer but we still need to be maintainers of it. See how it was done for IMX8QM.

Quoted 132 lines
 4 files changed, 292 insertions(+)
 create mode 100644 xen/arch/arm/include/asm/imx-uart.h
 create mode 100644 xen/drivers/char/imx-uart.c
xen/arch/arm/include/asm/imx-uart.h new file +57 -0
new file mode 100644
index 0000000000..a3892020e6
@@ -0,0 +1,57 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Register definitions for the classic i.MX UART IP
+ * ("fsl,imx6q-uart" compatible), used as the console UART on the
+ * i.MX8M family.
+ *
+ * Register layout taken from Linux drivers/tty/serial/imx.c.
+ *
+ * Copyright 2026 Open-EP (E-Paper) Community
+ */
+
+#ifndef ASM_IMX_UART_H
+#define ASM_IMX_UART_H
+
+#include <xen/const.h>
+
+#define URXD0           0x00   /* Receiver Register */
+#define URTX0           0x40   /* Transmitter Register */
+#define UCR1            0x80   /* Control Register 1 */
+#define UCR2            0x84   /* Control Register 2 */
+#define USR1            0x94   /* Status Register 1 */
+#define USR2            0x98   /* Status Register 2 */
+#define UTS             0xb4   /* Test Register */
+
+#define URXD_RX_DATA    0xff
+
+#define UCR1_UARTEN     BIT(0, U)   /* UART enable */
+#define UCR1_ATDMAEN    BIT(2, U)   /* Aging DMA timer enable */
+#define UCR1_TXDMAEN    BIT(3, U)   /* Transmitter ready DMA enable */
+#define UCR1_TXMPTYEN   BIT(6, U)   /* Transmitter empty interrupt enable */
+#define UCR1_RXDMAEN    BIT(8, U)   /* Receiver ready DMA enable */
+#define UCR1_RRDYEN     BIT(9, U)   /* Receiver ready interrupt enable */
+#define UCR1_TRDYEN     BIT(13, U)  /* Transmitter ready interrupt enable */
+
+#define UCR2_SRST       BIT(0, U)   /* 0 = issue software reset */
+#define UCR2_RXEN       BIT(1, U)   /* Receiver enable */
+#define UCR2_TXEN       BIT(2, U)   /* Transmitter enable */
+
+#define USR1_TRDY       BIT(13, U)  /* Transmitter ready */
+
+#define USR2_RDR        BIT(0, U)   /* Receive data ready */
+#define USR2_ORE        BIT(1, U)   /* Overrun error */
+
+#define UTS_TXFULL      BIT(4, U)   /* TX FIFO full */
+#define UTS_RXEMPTY     BIT(5, U)   /* RX FIFO empty */
+#define UTS_TXEMPTY     BIT(6, U)   /* TX FIFO empty */
+
+#endif /* ASM_IMX_UART_H */
+
+/*
+ * Local variables:
+ * mode: C
+ * c-file-style: "BSD"
+ * c-basic-offset: 4
+ * indent-tabs-mode: nil
+ * End:
+ */
xen/drivers/char/Kconfig +8 -0
index 8e49a52c73..f237c0220d 100644
@@ -30,6 +30,14 @@ config HAS_IMX_LPUART
 	help
 	  This selects the i.MX LPUART. If you have i.MX8QM based board, say Y.
 
+config HAS_IMX_UART
+	bool "i.MX UART driver"
+	default y
+	depends on ARM_64
+	help
+	  This selects the classic i.MX UART. If you have an i.MX8M family
+	  based board, say Y.
+
 config HAS_MVEBU
 	bool "Marvell MVEBU UART driver"
 	default y
xen/drivers/char/Makefile +1 -0
index 8cbbffdca8..039f566926 100644
@@ -10,6 +10,7 @@ obj-$(CONFIG_HAS_SCIF) += scif-uart.o
 obj-$(CONFIG_HAS_EHCI) += ehci-dbgp.o
 obj-$(CONFIG_XHCI) += xhci-dbc.o
 obj-$(CONFIG_HAS_IMX_LPUART) += imx-lpuart.o
+obj-$(CONFIG_HAS_IMX_UART) += imx-uart.o
 obj-$(CONFIG_HAS_LINFLEX) += linflex-uart.o
 obj-$(CONFIG_GENERIC_UART_INIT) += uart-init.o
 obj-y += serial.o
xen/drivers/char/imx-uart.c new file +28 -0
new file mode 100644
index 0000000000..fd34b0cd11
@@ -0,0 +1,226 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Driver for the classic i.MX UART IP ("fsl,imx6q-uart"), used as the
+ * console UART on the i.MX8M family (e.g. i.MX8MP).
+ *
+ * Baudrate and pin configuration are inherited from the bootloader.
+ *
+ * Copyright 2026 Open-EP (E-Paper) Community
+ */
+
+#include <xen/errno.h>
+#include <xen/init.h>
+#include <xen/irq.h>
+#include <xen/mm.h>
+#include <xen/serial.h>
+#include <asm/device.h>
+#include <asm/imx-uart.h>
+#include <asm/io.h>
+
+#define imx_uart_read(uart, off)       readl((uart)->regs + (off))
+#define imx_uart_write(uart, off, val) writel((val), (uart)->regs + (off))
+
+static struct imx_uart {
+    uint32_t irq;
+    char __iomem *regs;
+    struct irqaction irqaction;
+    struct vuart_info vuart;
+} imx8m_com;

xen/drivers/char/imx-uart.c line 38

Quoted 10 lines
xen/drivers/char/imx-uart.c new file +10 -0
+
+static void imx_uart_interrupt(int irq, void *data)
+{
+    struct serial_port *port = data;
+    struct imx_uart *uart = port->uart;
+
+    if ( imx_uart_read(uart, USR2) & USR2_RDR )
+        serial_rx_interrupt(port);
+
+    if ( imx_uart_read(uart, USR1) & USR1_TRDY )

Looking at Linux's imx.c you should clear TRDY if TRDEN is not enabled to prevent RX interrupt entering serial_tx_interrupt as TRDY is a raw status register.

Quoted 26 lines
xen/drivers/char/imx-uart.c new file +26 -0
+        serial_tx_interrupt(port);
+}
+
+static void __init imx_uart_init_preirq(struct serial_port *port)
+{
+    struct imx_uart *uart = port->uart;
+    uint32_t ucr1, ucr2;
+
+    /*
+     * Reuse the bootloader settings; only enable the UART and both
+     * directions.  The console uses UCR1 interrupts (RRDYEN/TRDYEN)
+     * exclusively, so just clear UCR1's interrupt and DMA enables.
+     */
+    ucr1 = imx_uart_read(uart, UCR1);
+    ucr1 &= ~(UCR1_RRDYEN | UCR1_TRDYEN | UCR1_TXMPTYEN | UCR1_RXDMAEN |
+              UCR1_TXDMAEN | UCR1_ATDMAEN);
+    ucr1 |= UCR1_UARTEN;
+    imx_uart_write(uart, UCR1, ucr1);
+
+    ucr2 = imx_uart_read(uart, UCR2);
+    ucr2 |= UCR2_SRST | UCR2_RXEN | UCR2_TXEN;
+    imx_uart_write(uart, UCR2, ucr2);
+}
+
+static void __init imx_uart_init_postirq(struct serial_port *port)
+{

xen/drivers/char/imx-uart.c line 74

Quoted 10 lines
xen/drivers/char/imx-uart.c new file +10 -0
+    struct imx_uart *uart = port->uart;
+    uint32_t ucr1;
+
+    uart->irqaction.handler = imx_uart_interrupt;
+    uart->irqaction.name = "imx_uart";
+    uart->irqaction.dev_id = port;
+
+    if ( setup_irq(uart->irq, 0, &uart->irqaction) != 0 )
+    {
+        dprintk(XENLOG_ERR, "Failed to allocate imx_uart IRQ %d\n", uart->irq);

uart->irq is unsigned, so s/%d/%u.

~Michal

author
#5 lore raw

PATCH v2 2/4 xen/arm64: add early printk for the classic i.MX UART

In reply to Wig Cheng

Add an early printk implementation for the classic i.MX UART IP, selectable via EARLY_UART_CHOICE_IMX_UART. The UART is expected to be fully initialized by the bootloader.

---
 xen/arch/arm/Kconfig.debug            | 12 +++++++++
 xen/arch/arm/arm64/debug-imx-uart.inc | 37 +++++++++++++++++++++++++++
 2 files changed, 49 insertions(+)
 create mode 100644 xen/arch/arm/arm64/debug-imx-uart.inc
xen/arch/arm/Kconfig.debug +12 -0
index 5a03b220ac..63a34b813a 100644
@@ -44,6 +44,14 @@ choice
 		  Say Y here if you wish the early printk to direct their
 		  output to a i.MX LPUART.
 
+	config EARLY_UART_CHOICE_IMX_UART
+		select EARLY_UART_IMX_UART
+		depends on ARM_64
+		bool "Early printk via i.MX UART"
+		help
+		  Say Y here if you wish the early printk to direct their
+		  output to the classic i.MX UART (i.MX8M family).
+
 	config EARLY_UART_CHOICE_LINFLEX
 		select EARLY_UART_LINFLEX
 		depends on ARM_64
@@ -97,6 +105,9 @@ config EARLY_UART_EXYNOS4210
 config EARLY_UART_IMX_LPUART
 	select EARLY_PRINTK
 	bool
+config EARLY_UART_IMX_UART
+	select EARLY_PRINTK
+	bool
 config EARLY_UART_LINFLEX
 	select EARLY_PRINTK
 	bool
@@ -185,6 +196,7 @@ config EARLY_PRINTK_INC
 	default "debug-cadence.inc" if EARLY_UART_CADENCE
 	default "debug-exynos4210.inc" if EARLY_UART_EXYNOS4210
 	default "debug-imx-lpuart.inc" if EARLY_UART_IMX_LPUART
+	default "debug-imx-uart.inc" if EARLY_UART_IMX_UART
 	default "debug-linflex.inc" if EARLY_UART_LINFLEX
 	default "debug-meson.inc" if EARLY_UART_MESON
 	default "debug-mvebu.inc" if EARLY_UART_MVEBU
xen/arch/arm/arm64/debug-imx-uart.inc new file +37 -0
new file mode 100644
index 0000000000..19b1679020
@@ -0,0 +1,37 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Early printk for the classic i.MX UART IP (i.MX8M family).
+ * The UART is expected to be fully initialized by the bootloader.
+ *
+ * Copyright 2026 Open-EP (E-Paper) Community
+ */
+
+#include <asm/imx-uart.h>
+
+/*
+ * Wait for the UART to be ready to transmit
+ * xb: register which contains the UART base address
+ * c: scratch register
+ */
+.macro early_uart_ready xb, c
+1:
+        ldr   w\c, [\xb, #UTS]        /* <- Test register */
+        tst   w\c, #UTS_TXFULL        /* Check TX FIFO full bit */
+        b.ne  1b                      /* Wait until there is room */
+.endm
+
+/*
+ * UART transmit character
+ * xb: register which contains the UART base address
+ * wt: register which contains the character to transmit
+ */
+.macro early_uart_transmit xb, wt
+        str   \wt, [\xb, #URTX0]      /* -> Transmitter register */
+.endm
+
+/*
+ * Local variables:
+ * mode: ASM
+ * indent-tabs-mode: nil
+ * End:
+ */
Signature · 1 line
2.43.0
Reviewed-by on v2 2/4
#6 lore raw

Re: [PATCH v2 2/4] xen/arm64: add early printk for the classic i.MX UART

Quoted 5 lines · Wig Cheng

Add an early printk implementation for the classic i.MX UART IP, selectable via EARLY_UART_CHOICE_IMX_UART. The UART is expected to be fully initialized by the bootloader.

~Michal

author
#7 lore raw

PATCH v2 3/4 xen/arm: add i.MX8M platform support

In reply to Wig Cheng

Add platform glue for the NXP i.MX8M family (i.MX8MP/MQ/MM/MN).

When Linux is used as dom0 a number of drivers make SiP SMC calls into TF-A to manage hardware: GPC power domains, DDR frequency scaling, SRC (M-core remoteproc), SoC info and NoC QoS. There is no public specification for these calls; the function IDs and their subfunctions are taken from the vendor kernel call sites.

Forward only the specific subfunctions the hardware domain issues, following the whitelist model of the i.MX8QM platform. Where a service has a fixed set of subfunctions (GPC, SRC, NoC) they are filtered; DDR DVFS is left at service level because its reg1 is a frequency setpoint rather than a fixed subfunction id, and the SoC info call is a read-only query. CPU frequency scaling is denied because the hardware domain cannot make an informed decision, and any unknown function ID is rejected.

---
 xen/arch/arm/platforms/Makefile |   1 +
 xen/arch/arm/platforms/imx8m.c  | 152 ++++++++++++++++++++++++++++++++
 2 files changed, 153 insertions(+)
 create mode 100644 xen/arch/arm/platforms/imx8m.c
xen/arch/arm/platforms/Makefile +1 -0
index bec6e55d1f..cdf936c50d 100644
@@ -9,6 +9,7 @@ obj-$(CONFIG_ALL_PLAT)   += sunxi.o
 obj-$(CONFIG_ALL64_PLAT) += thunderx.o
 obj-$(CONFIG_ALL64_PLAT) += xgene-storm.o
 obj-$(CONFIG_ALL64_PLAT) += brcm-raspberry-pi.o
+obj-$(CONFIG_ALL64_PLAT) += imx8m.o
 obj-$(CONFIG_ALL64_PLAT) += imx8qm.o
 obj-$(CONFIG_MPSOC_PLATFORM)  += xilinx-zynqmp.o
 obj-$(CONFIG_MPSOC_PLATFORM)  += xilinx-zynqmp-eemi.o
xen/arch/arm/platforms/imx8m.c new file +152 -0

152 lines not on this page · raw message

Signature · 1 line
2.43.0
#8 lore raw

Re: [PATCH v2 3/4] xen/arm: add i.MX8M platform support

Quoted 42 lines · Wig Cheng

Add platform glue for the NXP i.MX8M family (i.MX8MP/MQ/MM/MN).

When Linux is used as dom0 a number of drivers make SiP SMC calls into TF-A to manage hardware: GPC power domains, DDR frequency scaling, SRC (M-core remoteproc), SoC info and NoC QoS. There is no public specification for these calls; the function IDs and their subfunctions are taken from the vendor kernel call sites.

Forward only the specific subfunctions the hardware domain issues, following the whitelist model of the i.MX8QM platform. Where a service has a fixed set of subfunctions (GPC, SRC, NoC) they are filtered; DDR DVFS is left at service level because its reg1 is a frequency setpoint rather than a fixed subfunction id, and the SoC info call is a read-only query. CPU frequency scaling is denied because the hardware domain cannot make an informed decision, and any unknown function ID is rejected.

---
 xen/arch/arm/platforms/Makefile |   1 +
 xen/arch/arm/platforms/imx8m.c  | 152 ++++++++++++++++++++++++++++++++
 2 files changed, 153 insertions(+)
 create mode 100644 xen/arch/arm/platforms/imx8m.c
xen/arch/arm/platforms/Makefile +1 -0
index bec6e55d1f..cdf936c50d 100644
@@ -9,6 +9,7 @@ obj-$(CONFIG_ALL_PLAT)   += sunxi.o
 obj-$(CONFIG_ALL64_PLAT) += thunderx.o
 obj-$(CONFIG_ALL64_PLAT) += xgene-storm.o
 obj-$(CONFIG_ALL64_PLAT) += brcm-raspberry-pi.o
+obj-$(CONFIG_ALL64_PLAT) += imx8m.o
 obj-$(CONFIG_ALL64_PLAT) += imx8qm.o
 obj-$(CONFIG_MPSOC_PLATFORM)  += xilinx-zynqmp.o
 obj-$(CONFIG_MPSOC_PLATFORM)  += xilinx-zynqmp-eemi.o
xen/arch/arm/platforms/imx8m.c new file +0 -0
new file mode 100644
index 0000000000..fcf01298d8

xen/arch/arm/platforms/imx8m.c line 10

Quoted 10 lines
xen/arch/arm/platforms/imx8m.c new file +10 -0
@@ -0,0 +1,152 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * i.MX 8M family setup
+ *
+ * Copyright 2026 Open-EP (E-Paper) Community
+ */
+
+#include <xen/sched.h>
+#include <asm/platform.h>
+#include <asm/smccc.h>

You should also include asm/regs.h for get/set_user_regs()

Quoted 14 lines
xen/arch/arm/platforms/imx8m.c new file +14 -0
+
+static const char * const imx8m_dt_compat[] __initconst =
+{
+    "fsl,imx8mp",
+    "fsl,imx8mq",
+    "fsl,imx8mm",
+    "fsl,imx8mn",
+    NULL
+};
+
+#define IMX_SIP_FID(fid) \
+    ARM_SMCCC_CALL_VAL(ARM_SMCCC_FAST_CALL, \
+                       ARM_SMCCC_CONV_64, \
+                       ARM_SMCCC_OWNER_SIP, \

xen/arch/arm/platforms/imx8m.c line 34

Quoted 10 lines
xen/arch/arm/platforms/imx8m.c new file +10 -0
+                       (fid))
+
+/*
+ * SiP SMC function IDs used by the i.MX8M Linux drivers.  There is no
+ * public specification for these; the IDs and their subfunctions are
+ * extracted from the vendor kernel call sites (see drivers/soc/imx,
+ * drivers/devfreq, drivers/remoteproc).
+ */
+#define IMX_SIP_F_GPC       0x0   /* GPC power-domain control */
+#define IMX_SIP_F_CPUFREQ   0x1

Why no description?

xen/arch/arm/platforms/imx8m.c line 42

Quoted 8 lines
xen/arch/arm/platforms/imx8m.c new file +8 -0
+#define IMX_SIP_F_DDR_DVFS  0x4   /* DRAM frequency scaling */
+#define IMX_SIP_F_SRC       0x5   /* SRC: M-core remoteproc start/stop */
+#define IMX_SIP_F_SOC_INFO  0x6   /* read-only SoC info query */
+#define IMX_SIP_F_NOC       0x8   /* NoC QoS priority setup */
+
+#define IMX_SIP_GPC_SF_PM_DOMAIN    0x03
+
+#define IMX_SIP_SRC_SF_M4_START     0x00

This seems to be unused. Why?

xen/arch/arm/platforms/imx8m.c line 45

Quoted 3 lines
xen/arch/arm/platforms/imx8m.c new file +3 -0
+#define IMX_SIP_SRC_SF_M4_STOP      0x02
+
+#define IMX_SIP_NOC_SF_LCDIF        0x00

This seems to be unused. Why?

Quoted 26 lines
xen/arch/arm/platforms/imx8m.c new file +26 -0
+#define IMX_SIP_NOC_SF_PRIORITY     0x01
+
+static bool imx8m_smc(struct cpu_user_regs *regs)
+{
+    uint32_t function_id = get_user_reg(regs, 0);
+    uint32_t subfunction_id = get_user_reg(regs, 1);
+    struct arm_smccc_res res;
+
+    if ( !cpus_have_const_cap(ARM_SMCCC_1_1) )
+    {
+        printk_once(XENLOG_WARNING
+                    "imx8m: smc: no SMCCC 1.1 support. Disabling firmware calls\n");
+
+        return false;
+    }
+
+    /* Only the hardware domain may use the SiP calls */
+    if ( !is_hardware_domain(current->domain) )
+    {
+        gprintk(XENLOG_WARNING, "imx8m: smc: No access\n");
+        return false;
+    }
+
+    /*
+     * Forward only the subfunctions the dom0 kernel actually issues.  All
+     * of these manage hardware that belongs to the hardware domain (power

xen/arch/arm/platforms/imx8m.c line 81

Quoted 10 lines
xen/arch/arm/platforms/imx8m.c new file +10 -0
+     * domains, DRAM controller, M-core, NoC) or are read-only queries.
+     */
+    switch ( function_id )
+    {
+    case IMX_SIP_FID(IMX_SIP_F_GPC):
+        if ( subfunction_id != IMX_SIP_GPC_SF_PM_DOMAIN )
+            goto deny_subfunction;
+        break;
+
+    case IMX_SIP_FID(IMX_SIP_F_SRC):

Please list the cases in an order (GPC, CPUFREQ ...)

xen/arch/arm/platforms/imx8m.c line 91

Quoted 10 lines
xen/arch/arm/platforms/imx8m.c new file +10 -0
+        if ( subfunction_id > IMX_SIP_SRC_SF_M4_STOP )
+            goto deny_subfunction;
+        break;
+
+    case IMX_SIP_FID(IMX_SIP_F_NOC):
+        if ( subfunction_id > IMX_SIP_NOC_SF_PRIORITY )
+            goto deny_subfunction;
+        break;
+
+    case IMX_SIP_FID(IMX_SIP_F_DDR_DVFS):

IMO the stated reason for CPUFREQ applies here as well and we should rather deny this call. What makes it safe in your opinion to allow this call?

Quoted 35 lines
xen/arch/arm/platforms/imx8m.c new file +35 -0
+        /*
+         * For DDR DVFS reg1 is a frequency setpoint index (or the
+         * GET_FREQ_COUNT / GET_FREQ_INFO query), not a fixed subfunction
+         * id, so it is not filtered here.
+         */
+        break;
+
+    case IMX_SIP_FID(IMX_SIP_F_SOC_INFO):
+        break;
+
+    /*
+     * CPU frequency scaling: the hardware domain does not see the whole
+     * system and cannot make an informed decision, so deny it (matches
+     * the i.MX8QM platform).
+     */
+    case IMX_SIP_FID(IMX_SIP_F_CPUFREQ):
+        return false;
+
+    default:
+        gprintk(XENLOG_WARNING, "imx8m: smc: Unknown function id %x\n",
+                function_id);
+        return false;
+    }
+
+    arm_smccc_1_1_smc(function_id,
+                      subfunction_id,
+                      get_user_reg(regs, 2),
+                      get_user_reg(regs, 3),
+                      get_user_reg(regs, 4),
+                      get_user_reg(regs, 5),
+                      get_user_reg(regs, 6),
+                      get_user_reg(regs, 7),
+                      &res);
+
+    set_user_reg(regs, 0, res.a0);

xen/arch/arm/platforms/imx8m.c line 136

Quoted 10 lines
xen/arch/arm/platforms/imx8m.c new file +10 -0
+    set_user_reg(regs, 1, res.a1);
+    set_user_reg(regs, 2, res.a2);
+    set_user_reg(regs, 3, res.a3);
+
+    return true;
+
+ deny_subfunction:
+    gprintk(XENLOG_WARNING,
+            "imx8m: smc: function %x: denied subfunction %x\n",
+            function_id, subfunction_id);

IMO just return false directly on deny, no need for goto and printk, given that Xen will also print Unhandled SMC/HVC from vsmccc_handle_call().

Quoted 16 lines
xen/arch/arm/platforms/imx8m.c new file +16 -0
+    return false;
+}
+
+PLATFORM_START(imx8m, "i.MX 8M")
+    .compatible = imx8m_dt_compat,
+    .smc = imx8m_smc,
+PLATFORM_END
+
+/*
+ * Local variables:
+ * mode: C
+ * c-file-style: "BSD"
+ * c-basic-offset: 4
+ * indent-tabs-mode: nil
+ * End:
+ */
author
#9 lore raw

PATCH v2 4/4 MAINTAINERS: add myself as reviewer of i.MX8M related patches

In reply to Wig Cheng

I wrote the i.MX8M platform and UART support and can help review patches touching these areas.

---
 MAINTAINERS | 7 +++++++
 1 file changed, 7 insertions(+)
MAINTAINERS +7 -0
index ed0ffa608f..0434377fe1 100644
@@ -364,6 +364,13 @@ F:	tools/misc/xenhypfs.c
 F:	xen/common/hypfs.c
 F:	xen/include/xen/hypfs.h
 
+IMX8M SUPPORT
+R:	Wig Cheng <[email protected]>
+F:	xen/arch/arm/arm64/debug-imx-uart.inc
+F:	xen/arch/arm/include/asm/imx-uart.h
+F:	xen/arch/arm/platforms/imx8m.c
+F:	xen/drivers/char/imx-uart.c
+
 IMX8QM/QXP SUPPORT
 R:	John Ernberg <[email protected]>
 F:	xen/arch/arm/platforms/imx8qm.c
Signature · 1 line
2.43.0
#11 lore raw
In reply to Wig Cheng
Quoted 26 lines · Wig Cheng

Following Michal Orzel's review of v1, this series adds Xen support for the NXP i.MX8M family (i.MX8MP / MQ / MM / MN). It provides the console UART driver, its early printk, the platform glue (SiP SMC whitelist for the calls the dom0 kernel issues to TF-A), and a MAINTAINERS entry.

Tested on i.MX8MP (4x Cortex-A53, GICv3) with the vendor kernel 6.18:
dom0 boots to login on the hypervisor console, and a domU starts with a PV disk and virtio devices running a full Wayland distro.

Notes for reviewers:

- Unlike i.MX8MQ, the i.MX8MP device tree uses the GIC as the root interrupt controller (interrupt-parent = <&gic>), so no device-tree workaround is needed and power domains keep working.

- The i.MX8M family has no SMMU, so device passthrough relies on the 1:1 direct-mapped hardware domain.

- The SiP SMC whitelist forwards only the specific subfunctions the dom0 kernel issues, extracted from the vendor kernel call sites. DDR DVFS is left at service level because its reg1 is a frequency setpoint rather than a fixed subfunction id. No call was denied at runtime.

Changes since v1:

Quoted 8 lines

Patch 1 (UART driver):
- Documentation narrowed to the i.MX8M family (dropped i.MX6/7).
- Relicensed the new files as GPL-2.0-only.
- Dropped the stale file-path lines from the file headers.
- Renamed the header guard to ASM_IMX_UART_H.
- Removed unused register/bit macros; header is now asm-safe (BIT(n, U)).
- Also clear UCR1_TXMPTYEN on init; documented that the console is driven entirely through UCR1.

For the future, please include the changeset in the individual patches. This way it's easier for us to review without having to switch between e-mails.

~Michal

Quoted 39 lines

Patch 2 (early printk):
- bne -> b.ne.

Patch 3 (platform):
- Build the SiP function IDs with ARM_SMCCC_CALL_VAL (IMX_SIP_FID), matching the i.MX8QM platform.
- Whitelist per subfunction (GPC, SRC, NoC) instead of whole services; DDR DVFS and SoC info kept at service level with a comment on why.
- Dropped the BBSM call, which is not issued on i.MX8M.
- Fixed the misleading "secure RTC" comment and a stray space.

Patch 4 (new):
- MAINTAINERS entry, as a separate patch.

v1: https://lore.kernel.org/xen-devel/[email protected]/

Wig Cheng (4):
xen/char: add classic i.MX UART driver
xen/arm64: add early printk for the classic i.MX UART xen/arm: add i.MX8M platform support
MAINTAINERS: add myself as reviewer of i.MX8M related patches

 MAINTAINERS                           |   7 +
 xen/arch/arm/Kconfig.debug            |  12 ++
 xen/arch/arm/arm64/debug-imx-uart.inc |  37 +++++
 xen/arch/arm/include/asm/imx-uart.h   |  57 +++++++
 xen/arch/arm/platforms/Makefile       |   1 +
 xen/arch/arm/platforms/imx8m.c        | 152 +++++++++++++++++
 xen/drivers/char/Kconfig              |   8 +
 xen/drivers/char/Makefile             |   1 +
 xen/drivers/char/imx-uart.c           | 226 ++++++++++++++++++++++++++
 9 files changed, 501 insertions(+)
 create mode 100644 xen/arch/arm/arm64/debug-imx-uart.inc
 create mode 100644 xen/arch/arm/include/asm/imx-uart.h
 create mode 100644 xen/arch/arm/platforms/imx8m.c
 create mode 100644 xen/drivers/char/imx-uart.c