PCI: mediatek-gen3: Add support for disable dvfsrc
Subsystems (5)
v3 cover PCI: mediatek-gen3: Add support for disable dvfsrc
These series patches add support for disable dvfsrc voltage request.
Changes in v3:
Fix typo.
Changes in v2:
Fix typo.
Jianjun Wang (2):
dt-bindings: PCI: mediatek-gen3: Add property to disable dvfsrc
voltage request
PCI: mediatek-gen3: Add support for disable dvfsrc voltage request
.../bindings/pci/mediatek-pcie-gen3.yaml | 8 +++++ drivers/pci/controller/pcie-mediatek-gen3.c | 31 +++++++++++++++++++ 2 files changed, 39 insertions(+)
Signature · 1 line
2.18.0
PATCH v3 1/2 dt-bindings: PCI: mediatek-gen3: Add property to disable dvfsrc voltage request
Add property to disable dvfsrc voltage request, if this property is presented, we assume that the requested voltage is always higher enough to keep the PCIe controller active.
--- .../devicetree/bindings/pci/mediatek-pcie-gen3.yaml | 8 ++++++++ 1 file changed, 8 insertions(+)
Documentation/devicetree/bindings/pci/mediatek-pcie-gen3.yaml +8 -0
@@ -96,6 +96,12 @@ properties: phys: maxItems: 1 + disable-dvfsrc-vlt-req: + description: Disable dvfsrc voltage request, if this property is presented, + we assume that the requested voltage is always higher enough to keep + the PCIe controller active. + type: boolean + '#interrupt-cells': const: 1
@@ -166,6 +172,8 @@ examples: <&infracfg_rst 3>; reset-names = "phy", "mac"; + disable-dvfsrc-vlt-req; + #interrupt-cells = <1>; interrupt-map-mask = <0 0 0 0x7>; interrupt-map = <0 0 0 1 &pcie_intc 0>,
Signature · 1 line
2.18.0
Re: [PATCH v3 1/2] dt-bindings: PCI: mediatek-gen3: Add property to disable dvfsrc voltage request
Quoted 35 lines · Jianjun Wang
Add property to disable dvfsrc voltage request, if this property is presented, we assume that the requested voltage is always higher enough to keep the PCIe controller active.
Signed-off-by Jianjun Wang <[email protected]>--- .../devicetree/bindings/pci/mediatek-pcie-gen3.yaml | 8 ++++++++ 1 file changed, 8 insertions(+)Documentation/devicetree/bindings/pci/mediatek-pcie-gen3.yaml +8
-0@@ -96,6 +96,12 @@ properties: phys: maxItems: 1 + disable-dvfsrc-vlt-req: + description: Disable dvfsrc voltage request, if this property is presented, + we assume that the requested voltage is always higher enough to keep + the PCIe controller active. + type: boolean + '#interrupt-cells': const: 1@@ -166,6 +172,8 @@ examples: <&infracfg_rst 3>; reset-names = "phy", "mac"; + disable-dvfsrc-vlt-req; + #interrupt-cells = <1>; interrupt-map-mask = <0 0 0 0x7>; interrupt-map = <0 0 0 1 &pcie_intc 0>,
Re: [PATCH v3 1/2] dt-bindings: PCI: mediatek-gen3: Add property to disable dvfsrc voltage request
Hi,
Just gentle ping for this patch set, please kindly let me know your comments about this patch set.
Thanks.
Quoted 41 lines · Qizhong Cheng
Reviewed-by Qizhong Cheng <[email protected]>Tested-by Qizhong Cheng <[email protected]>Quoted 35 lines · Jianjun Wang
Add property to disable dvfsrc voltage request, if this property is presented, we assume that the requested voltage is always higher enough to keep the PCIe controller active.
Signed-off-by Jianjun Wang <[email protected]>--- .../devicetree/bindings/pci/mediatek-pcie-gen3.yaml | 8 ++++++++ 1 file changed, 8 insertions(+)Documentation/devicetree/bindings/pci/mediatek-pcie-gen3.yaml +8
-0@@ -96,6 +96,12 @@ properties: phys: maxItems: 1 + disable-dvfsrc-vlt-req: + description: Disable dvfsrc voltage request, if this property is presented, + we assume that the requested voltage is always higher enough to keep + the PCIe controller active. + type: boolean + '#interrupt-cells': const: 1@@ -166,6 +172,8 @@ examples: <&infracfg_rst 3>; reset-names = "phy", "mac"; + disable-dvfsrc-vlt-req; + #interrupt-cells = <1>; interrupt-map-mask = <0 0 0 0x7>; interrupt-map = <0 0 0 1 &pcie_intc 0>,
Rob Herring
maintainerRe: [PATCH v3 1/2] dt-bindings: PCI: mediatek-gen3: Add property to disable dvfsrc voltage request
In reply to Jianjun WangQuoted 14 lines · Jianjun Wang
Add property to disable dvfsrc voltage request, if this property is presented, we assume that the requested voltage is always higher enough to keep the PCIe controller active.
Signed-off-by Jianjun Wang <[email protected]>--- .../devicetree/bindings/pci/mediatek-pcie-gen3.yaml | 8 ++++++++ 1 file changed, 8 insertions(+)Documentation/devicetree/bindings/pci/mediatek-pcie-gen3.yaml +0
-0
Documentation/devicetree/bindings/pci/mediatek-pcie-gen3.yaml properties: · line 103
Quoted 8 lines
Documentation/devicetree/bindings/pci/mediatek-pcie-gen3.yaml +5
-0@@ -96,6 +96,12 @@ properties: phys: maxItems: 1 + disable-dvfsrc-vlt-req: + description: Disable dvfsrc voltage request, if this property is presented, + we assume that the requested voltage is always higher enough to keep + the PCIe controller active. + type: boolean
What determines setting this property? Can it be implied by the compatible (which should be SoC specific).
Is this property specific to PCIe controller?
Wouldn't the request be harmless to make the voltage request even if not needed?
I think this probably should be addressed in a common way as part of other QoS, devfreq, etc. requirements for devices.
Rob
Re: [PATCH v3 1/2] dt-bindings: PCI: mediatek-gen3: Add property to disable dvfsrc voltage request
Quoted 33 lines · Rob Herring
Quoted 25 lines · Jianjun Wang
Add property to disable dvfsrc voltage request, if this property is presented, we assume that the requested voltage is always higher enough to keep the PCIe controller active.
Signed-off-by Jianjun Wang <[email protected]>--- .../devicetree/bindings/pci/mediatek-pcie-gen3.yaml | 8 ++++++++ 1 file changed, 8 insertions(+)(quoted diff) +0
-0
gen3.yamlb/Documentation/devicetree/bindings/pci/mediatek-pcie-gen3.yaml
indexe7b1f9892da4..3e26c032cea9100644Documentation/devicetree/bindings/pci/mediatek-pcie-gen3.yaml +3
-0@@ -96,6 +96,12 @@ properties: phys: maxItems: 1 + disable-dvfsrc-vlt-req: + description: Disable dvfsrc voltage request, if this property is presented, + we assume that the requested voltage is always higher enoughto keep
Documentation/devicetree/bindings/pci/mediatek-pcie-gen3.yaml properties: · line 103
Quoted 2 lines
Documentation/devicetree/bindings/pci/mediatek-pcie-gen3.yaml +2
-0+ the PCIe controller active. + type: booleanWhat determines setting this property? Can it be implied by the compatible (which should be SoC specific).
Is this property specific to PCIe controller?
Quoted 8 lines
Wouldn't the request be harmless to make the voltage request even if not
needed?I think this probably should be addressed in a common way as part of other QoS, devfreq, etc. requirements for devices.
Rob
Hi Rob,
Thanks for your review and sorry for the late response.
We have internal discussion and we agree with that this feature should not be specific to the PCIe controller, we need to find a common way to do this.
But as the driver of dvfsrc is not finished the upstream, we don't have a better solution for now, so we would like to pull back this patch and will send another patch to disable dvfsrc by default until we find a common solution to enable it.
Thanks.
PATCH v3 2/2 PCI: mediatek-gen3: Add support for disable dvfsrc voltage request
In reply to Jianjun WangPCIe Gen3 PHY layer cannot work properly when the requested voltage is lower than a specific level(e.g. 0.55V, it's depends on the chip manufacturing process).
When the dvfsrc feature is implemented, the requested voltage may be reduced to a lower level in suspend mode, hence that the MAC layer will assert a HW signal to request the dvfsrc to raise voltage to normal mode, and it will wait the voltage ready signal from dvfsrc to decide if the LTSSM can start normally.
When the dvfsrc feature is not implemented, the MAC layer still assert the voltage request to dvfsrc when exit suspend mode, but will not receive the voltage ready signal, in this case, the LTSSM cannot start normally, and the PCIe link will be failed.
Add support for disable dvfsrc voltage request, if the property of "disable-dvfsrc-vlt-req" is presented in device node, we assume that the requested voltage is always higher enough to keep the PCIe Gen3 PHY active, and the voltage request to dvfsrc should be disabled.
--- drivers/pci/controller/pcie-mediatek-gen3.c | 31 +++++++++++++++++++++ 1 file changed, 31 insertions(+)
drivers/pci/controller/pcie-mediatek-gen3.c +31 -0
@@ -79,6 +79,9 @@#define PCIE_ICMD_PM_REG 0x198#define PCIE_TURN_OFF_LINK BIT(4) +#define PCIE_MISC_CTRL_REG 0x348 +#define PCIE_DISABLE_DVFSRC_VLT_REQ BIT(1) +#define PCIE_TRANS_TABLE_BASE_REG 0x800#define PCIE_ATR_SRC_ADDR_MSB_OFFSET 0x4#define PCIE_ATR_TRSL_ADDR_LSB_OFFSET 0x8
@@ -297,6 +300,34 @@ static int mtk_pcie_startup_port(struct mtk_pcie_port *port) val &= ~PCIE_INTX_ENABLE ;writel_relaxed (val, port->base +PCIE_INT_ENABLE_REG ); +/* +* PCIe Gen3 PHY layer can not work properly when the requested voltage +* is lower than a specific level(e.g. 0.55V, it's depends on +* the chip manufacturing process). +* +* When the dvfsrc feature is implemented, the requested voltage +* might be reduced to a lower level in suspend mode, hence that +* the MAC layer will assert a HW signal to request the dvfsrc +* to raise voltage to normal mode, and it will wait the voltage +* ready signal from dvfsrc to start the LTSSM normally. +* +* When the dvfsrc feature is not implemented, the MAC layer still +* assert the voltage request to dvfsrc when exit suspend mode, +* but will not get the voltage ready signal, in this case, the LTSSM +* cannot start normally, and the PCIe link will be failed. +* +* If the property of "disable-dvfsrc-vlt-req" is presented +* in device node, we assume that the requested voltage is always +* higher enough to keep the PCIe Gen3 PHY active, and the voltage +* request to dvfsrc should be disabled. +*/ + val =readl_relaxed (port->base +PCIE_MISC_CTRL_REG ); + val &= ~PCIE_DISABLE_DVFSRC_VLT_REQ ; +if (of_property_read_bool (port->dev->of_node,"disable-dvfsrc-vlt-req" )) + val |=PCIE_DISABLE_DVFSRC_VLT_REQ ; + +writel_relaxed (val, port->base +PCIE_MISC_CTRL_REG ); +/* Assert all reset signals */ val =readl_relaxed (port->base +PCIE_RST_CTRL_REG ); val |=PCIE_MAC_RSTB |PCIE_PHY_RSTB |PCIE_BRG_RSTB |PCIE_PE_RSTB ;
Signature · 1 line
2.18.0
Re: [PATCH v3 2/2] PCI: mediatek-gen3: Add support for disable dvfsrc voltage request
Quoted 74 lines · Jianjun Wang
PCIe Gen3 PHY layer cannot work properly when the requested voltage is lower than a specific level(e.g. 0.55V, it's depends on the chip manufacturing process).
When the dvfsrc feature is implemented, the requested voltage may be reduced to a lower level in suspend mode, hence that the MAC layer will assert a HW signal to request the dvfsrc to raise voltage to normal mode, and it will wait the voltage ready signal from dvfsrc to decide if the LTSSM can start normally.
When the dvfsrc feature is not implemented, the MAC layer still assert the voltage request to dvfsrc when exit suspend mode, but will not receive the voltage ready signal, in this case, the LTSSM cannot start normally, and the PCIe link will be failed.
Add support for disable dvfsrc voltage request, if the property of "disable-dvfsrc-vlt-req" is presented in device node, we assume that the requested voltage is always higher enough to keep the PCIe Gen3 PHY active, and the voltage request to dvfsrc should be disabled.
Signed-off-by Jianjun Wang <[email protected]>--- drivers/pci/controller/pcie-mediatek-gen3.c | 31 +++++++++++++++++++++ 1 file changed, 31 insertions(+)drivers/pci/controller/pcie-mediatek-gen3.c +31
-0@@ -79,6 +79,9 @@#define PCIE_ICMD_PM_REG 0x198#define PCIE_TURN_OFF_LINK BIT(4) +#define PCIE_MISC_CTRL_REG 0x348 +#define PCIE_DISABLE_DVFSRC_VLT_REQ BIT(1) +#define PCIE_TRANS_TABLE_BASE_REG 0x800#define PCIE_ATR_SRC_ADDR_MSB_OFFSET 0x4#define PCIE_ATR_TRSL_ADDR_LSB_OFFSET 0x8@@ -297,6 +300,34 @@ static int mtk_pcie_startup_port(struct mtk_pcie_port *port) val &= ~PCIE_INTX_ENABLE ;writel_relaxed (val, port->base +PCIE_INT_ENABLE_REG ); +/* +* PCIe Gen3 PHY layer can not work properly when the requested voltage +* is lower than a specific level(e.g. 0.55V, it's depends on +* the chip manufacturing process). +* +* When the dvfsrc feature is implemented, the requested voltage +* might be reduced to a lower level in suspend mode, hence that +* the MAC layer will assert a HW signal to request the dvfsrc +* to raise voltage to normal mode, and it will wait the voltage +* ready signal from dvfsrc to start the LTSSM normally. +* +* When the dvfsrc feature is not implemented, the MAC layer still +* assert the voltage request to dvfsrc when exit suspend mode, +* but will not get the voltage ready signal, in this case, the LTSSM +* cannot start normally, and the PCIe link will be failed. +* +* If the property of "disable-dvfsrc-vlt-req" is presented +* in device node, we assume that the requested voltage is always +* higher enough to keep the PCIe Gen3 PHY active, and the voltage +* request to dvfsrc should be disabled. +*/ + val =readl_relaxed (port->base +PCIE_MISC_CTRL_REG ); + val &= ~PCIE_DISABLE_DVFSRC_VLT_REQ ; +if (of_property_read_bool (port->dev->of_node,"disable-dvfsrc-vlt-req" )) + val |=PCIE_DISABLE_DVFSRC_VLT_REQ ; + +writel_relaxed (val, port->base +PCIE_MISC_CTRL_REG ); +/* Assert all reset signals */ val =readl_relaxed (port->base +PCIE_RST_CTRL_REG ); val |=PCIE_MAC_RSTB |PCIE_PHY_RSTB |PCIE_BRG_RSTB |PCIE_PE_RSTB ;