Skip to contentSkip to conversation

dmaengine: add support for sama7g5 based at_xdmac

PATCH In review Eugen Hristev 4 participants 19 messages Sep 14, 2020 – Oct 16, 2020

Subsystems (4)
lore
Share & tools
lore
#0 lore raw

cover dmaengine: add support for sama7g5 based at_xdmac

This series adds support for sama7g5-based at_xdmac.

In sama7g5, the XDMAC is present in a slightly modified form. This series tries to adapt the existing driver to the differences. According to the compatible string, we select one of two possible layouts, which hold the differences in registermap and supported features.

Thanks!

Eugen Hristev (7):
dmaengine: at_xdmac: separate register defines into header file
MAINTAINERS: add dma/at_xdmac_regs.h to XDMAC driver entry
dt-bindings: dmaengine: at_xdmac: add compatible with
microchip,sama7g5
dmaengine: at_xdmac: adapt perid for mem2mem operations
dmaengine: at_xdmac: add support for sama7g5 based at_xdmac
dt-bindings: dmaengine: at_xdmac: add optional microchip,m2m property
dmaengine: at_xdmac: add AXI priority support and recommended settings

 .../devicetree/bindings/dma/atmel-xdma.txt    |   9 +-
 MAINTAINERS                                   |   1 +
 drivers/dma/at_xdmac.c                        | 273 +++++++-----------
 drivers/dma/at_xdmac_regs.h                   | 161 +++++++++++
 4 files changed, 281 insertions(+), 163 deletions(-)
 create mode 100644 drivers/dma/at_xdmac_regs.h
Signature · 1 line
2.25.1
#1 lore raw

PATCH 1/7 dmaengine: at_xdmac: separate register defines into header file

Separate register defines into header file.
This is required to support a slightly different version of the register map in new hardware versions of the XDMAC.

---
 drivers/dma/at_xdmac.c      | 143 +--------------------------------
 drivers/dma/at_xdmac_regs.h | 154 ++++++++++++++++++++++++++++++++++++
 2 files changed, 155 insertions(+), 142 deletions(-)
 create mode 100644 drivers/dma/at_xdmac_regs.h
drivers/dma/at_xdmac.c +1 -142
index fd92f048c491..fab19e00a7be 100644
@@ -24,148 +24,7 @@
 
 #include "dmaengine.h"
 
-/* Global registers */
-#define AT_XDMAC_GTYPE		0x00	/* Global Type Register */
-#define		AT_XDMAC_NB_CH(i)	(((i) & 0x1F) + 1)		/* Number of Channels Minus One */
-#define		AT_XDMAC_FIFO_SZ(i)	(((i) >> 5) & 0x7FF)		/* Number of Bytes */
-#define		AT_XDMAC_NB_REQ(i)	((((i) >> 16) & 0x3F) + 1)	/* Number of Peripheral Requests Minus One */
-#define AT_XDMAC_GCFG		0x04	/* Global Configuration Register */
-#define AT_XDMAC_GWAC		0x08	/* Global Weighted Arbiter Configuration Register */
-#define AT_XDMAC_GIE		0x0C	/* Global Interrupt Enable Register */
-#define AT_XDMAC_GID		0x10	/* Global Interrupt Disable Register */
-#define AT_XDMAC_GIM		0x14	/* Global Interrupt Mask Register */
-#define AT_XDMAC_GIS		0x18	/* Global Interrupt Status Register */
-#define AT_XDMAC_GE		0x1C	/* Global Channel Enable Register */
-#define AT_XDMAC_GD		0x20	/* Global Channel Disable Register */
-#define AT_XDMAC_GS		0x24	/* Global Channel Status Register */
-#define AT_XDMAC_GRS		0x28	/* Global Channel Read Suspend Register */
-#define AT_XDMAC_GWS		0x2C	/* Global Write Suspend Register */
-#define AT_XDMAC_GRWS		0x30	/* Global Channel Read Write Suspend Register */
-#define AT_XDMAC_GRWR		0x34	/* Global Channel Read Write Resume Register */
-#define AT_XDMAC_GSWR		0x38	/* Global Channel Software Request Register */
-#define AT_XDMAC_GSWS		0x3C	/* Global channel Software Request Status Register */
-#define AT_XDMAC_GSWF		0x40	/* Global Channel Software Flush Request Register */
-#define AT_XDMAC_VERSION	0xFFC	/* XDMAC Version Register */
-
-/* Channel relative registers offsets */
-#define AT_XDMAC_CIE		0x00	/* Channel Interrupt Enable Register */
-#define		AT_XDMAC_CIE_BIE	BIT(0)	/* End of Block Interrupt Enable Bit */
-#define		AT_XDMAC_CIE_LIE	BIT(1)	/* End of Linked List Interrupt Enable Bit */
-#define		AT_XDMAC_CIE_DIE	BIT(2)	/* End of Disable Interrupt Enable Bit */
-#define		AT_XDMAC_CIE_FIE	BIT(3)	/* End of Flush Interrupt Enable Bit */
-#define		AT_XDMAC_CIE_RBEIE	BIT(4)	/* Read Bus Error Interrupt Enable Bit */
-#define		AT_XDMAC_CIE_WBEIE	BIT(5)	/* Write Bus Error Interrupt Enable Bit */
-#define		AT_XDMAC_CIE_ROIE	BIT(6)	/* Request Overflow Interrupt Enable Bit */
-#define AT_XDMAC_CID		0x04	/* Channel Interrupt Disable Register */
-#define		AT_XDMAC_CID_BID	BIT(0)	/* End of Block Interrupt Disable Bit */
-#define		AT_XDMAC_CID_LID	BIT(1)	/* End of Linked List Interrupt Disable Bit */
-#define		AT_XDMAC_CID_DID	BIT(2)	/* End of Disable Interrupt Disable Bit */
-#define		AT_XDMAC_CID_FID	BIT(3)	/* End of Flush Interrupt Disable Bit */
-#define		AT_XDMAC_CID_RBEID	BIT(4)	/* Read Bus Error Interrupt Disable Bit */
-#define		AT_XDMAC_CID_WBEID	BIT(5)	/* Write Bus Error Interrupt Disable Bit */
-#define		AT_XDMAC_CID_ROID	BIT(6)	/* Request Overflow Interrupt Disable Bit */
-#define AT_XDMAC_CIM		0x08	/* Channel Interrupt Mask Register */
-#define		AT_XDMAC_CIM_BIM	BIT(0)	/* End of Block Interrupt Mask Bit */
-#define		AT_XDMAC_CIM_LIM	BIT(1)	/* End of Linked List Interrupt Mask Bit */
-#define		AT_XDMAC_CIM_DIM	BIT(2)	/* End of Disable Interrupt Mask Bit */
-#define		AT_XDMAC_CIM_FIM	BIT(3)	/* End of Flush Interrupt Mask Bit */
-#define		AT_XDMAC_CIM_RBEIM	BIT(4)	/* Read Bus Error Interrupt Mask Bit */
-#define		AT_XDMAC_CIM_WBEIM	BIT(5)	/* Write Bus Error Interrupt Mask Bit */
-#define		AT_XDMAC_CIM_ROIM	BIT(6)	/* Request Overflow Interrupt Mask Bit */
-#define AT_XDMAC_CIS		0x0C	/* Channel Interrupt Status Register */
-#define		AT_XDMAC_CIS_BIS	BIT(0)	/* End of Block Interrupt Status Bit */
-#define		AT_XDMAC_CIS_LIS	BIT(1)	/* End of Linked List Interrupt Status Bit */
-#define		AT_XDMAC_CIS_DIS	BIT(2)	/* End of Disable Interrupt Status Bit */
-#define		AT_XDMAC_CIS_FIS	BIT(3)	/* End of Flush Interrupt Status Bit */
-#define		AT_XDMAC_CIS_RBEIS	BIT(4)	/* Read Bus Error Interrupt Status Bit */
-#define		AT_XDMAC_CIS_WBEIS	BIT(5)	/* Write Bus Error Interrupt Status Bit */
-#define		AT_XDMAC_CIS_ROIS	BIT(6)	/* Request Overflow Interrupt Status Bit */
-#define AT_XDMAC_CSA		0x10	/* Channel Source Address Register */
-#define AT_XDMAC_CDA		0x14	/* Channel Destination Address Register */
-#define AT_XDMAC_CNDA		0x18	/* Channel Next Descriptor Address Register */
-#define		AT_XDMAC_CNDA_NDAIF(i)	((i) & 0x1)			/* Channel x Next Descriptor Interface */
-#define		AT_XDMAC_CNDA_NDA(i)	((i) & 0xfffffffc)		/* Channel x Next Descriptor Address */
-#define AT_XDMAC_CNDC		0x1C	/* Channel Next Descriptor Control Register */
-#define		AT_XDMAC_CNDC_NDE		(0x1 << 0)		/* Channel x Next Descriptor Enable */
-#define		AT_XDMAC_CNDC_NDSUP		(0x1 << 1)		/* Channel x Next Descriptor Source Update */
-#define		AT_XDMAC_CNDC_NDDUP		(0x1 << 2)		/* Channel x Next Descriptor Destination Update */
-#define		AT_XDMAC_CNDC_NDVIEW_NDV0	(0x0 << 3)		/* Channel x Next Descriptor View 0 */
-#define		AT_XDMAC_CNDC_NDVIEW_NDV1	(0x1 << 3)		/* Channel x Next Descriptor View 1 */
-#define		AT_XDMAC_CNDC_NDVIEW_NDV2	(0x2 << 3)		/* Channel x Next Descriptor View 2 */
-#define		AT_XDMAC_CNDC_NDVIEW_NDV3	(0x3 << 3)		/* Channel x Next Descriptor View 3 */
-#define AT_XDMAC_CUBC		0x20	/* Channel Microblock Control Register */
-#define AT_XDMAC_CBC		0x24	/* Channel Block Control Register */
-#define AT_XDMAC_CC		0x28	/* Channel Configuration Register */
-#define		AT_XDMAC_CC_TYPE	(0x1 << 0)	/* Channel Transfer Type */
-#define			AT_XDMAC_CC_TYPE_MEM_TRAN	(0x0 << 0)	/* Memory to Memory Transfer */
-#define			AT_XDMAC_CC_TYPE_PER_TRAN	(0x1 << 0)	/* Peripheral to Memory or Memory to Peripheral Transfer */
-#define		AT_XDMAC_CC_MBSIZE_MASK	(0x3 << 1)
-#define			AT_XDMAC_CC_MBSIZE_SINGLE	(0x0 << 1)
-#define			AT_XDMAC_CC_MBSIZE_FOUR		(0x1 << 1)
-#define			AT_XDMAC_CC_MBSIZE_EIGHT	(0x2 << 1)
-#define			AT_XDMAC_CC_MBSIZE_SIXTEEN	(0x3 << 1)
-#define		AT_XDMAC_CC_DSYNC	(0x1 << 4)	/* Channel Synchronization */
-#define			AT_XDMAC_CC_DSYNC_PER2MEM	(0x0 << 4)
-#define			AT_XDMAC_CC_DSYNC_MEM2PER	(0x1 << 4)
-#define		AT_XDMAC_CC_PROT	(0x1 << 5)	/* Channel Protection */
-#define			AT_XDMAC_CC_PROT_SEC		(0x0 << 5)
-#define			AT_XDMAC_CC_PROT_UNSEC		(0x1 << 5)
-#define		AT_XDMAC_CC_SWREQ	(0x1 << 6)	/* Channel Software Request Trigger */
-#define			AT_XDMAC_CC_SWREQ_HWR_CONNECTED	(0x0 << 6)
-#define			AT_XDMAC_CC_SWREQ_SWR_CONNECTED	(0x1 << 6)
-#define		AT_XDMAC_CC_MEMSET	(0x1 << 7)	/* Channel Fill Block of memory */
-#define			AT_XDMAC_CC_MEMSET_NORMAL_MODE	(0x0 << 7)
-#define			AT_XDMAC_CC_MEMSET_HW_MODE	(0x1 << 7)
-#define		AT_XDMAC_CC_CSIZE(i)	((0x7 & (i)) << 8)	/* Channel Chunk Size */
-#define		AT_XDMAC_CC_DWIDTH_OFFSET	11
-#define		AT_XDMAC_CC_DWIDTH_MASK	(0x3 << AT_XDMAC_CC_DWIDTH_OFFSET)
-#define		AT_XDMAC_CC_DWIDTH(i)	((0x3 & (i)) << AT_XDMAC_CC_DWIDTH_OFFSET)	/* Channel Data Width */
-#define			AT_XDMAC_CC_DWIDTH_BYTE		0x0
-#define			AT_XDMAC_CC_DWIDTH_HALFWORD	0x1
-#define			AT_XDMAC_CC_DWIDTH_WORD		0x2
-#define			AT_XDMAC_CC_DWIDTH_DWORD	0x3
-#define		AT_XDMAC_CC_SIF(i)	((0x1 & (i)) << 13)	/* Channel Source Interface Identifier */
-#define		AT_XDMAC_CC_DIF(i)	((0x1 & (i)) << 14)	/* Channel Destination Interface Identifier */
-#define		AT_XDMAC_CC_SAM_MASK	(0x3 << 16)	/* Channel Source Addressing Mode */
-#define			AT_XDMAC_CC_SAM_FIXED_AM	(0x0 << 16)
-#define			AT_XDMAC_CC_SAM_INCREMENTED_AM	(0x1 << 16)
-#define			AT_XDMAC_CC_SAM_UBS_AM		(0x2 << 16)
-#define			AT_XDMAC_CC_SAM_UBS_DS_AM	(0x3 << 16)
-#define		AT_XDMAC_CC_DAM_MASK	(0x3 << 18)	/* Channel Source Addressing Mode */
-#define			AT_XDMAC_CC_DAM_FIXED_AM	(0x0 << 18)
-#define			AT_XDMAC_CC_DAM_INCREMENTED_AM	(0x1 << 18)
-#define			AT_XDMAC_CC_DAM_UBS_AM		(0x2 << 18)
-#define			AT_XDMAC_CC_DAM_UBS_DS_AM	(0x3 << 18)
-#define		AT_XDMAC_CC_INITD	(0x1 << 21)	/* Channel Initialization Terminated (read only) */
-#define			AT_XDMAC_CC_INITD_TERMINATED	(0x0 << 21)
-#define			AT_XDMAC_CC_INITD_IN_PROGRESS	(0x1 << 21)
-#define		AT_XDMAC_CC_RDIP	(0x1 << 22)	/* Read in Progress (read only) */
-#define			AT_XDMAC_CC_RDIP_DONE		(0x0 << 22)
-#define			AT_XDMAC_CC_RDIP_IN_PROGRESS	(0x1 << 22)
-#define		AT_XDMAC_CC_WRIP	(0x1 << 23)	/* Write in Progress (read only) */
-#define			AT_XDMAC_CC_WRIP_DONE		(0x0 << 23)
-#define			AT_XDMAC_CC_WRIP_IN_PROGRESS	(0x1 << 23)
-#define		AT_XDMAC_CC_PERID(i)	(0x7f & (i) << 24)	/* Channel Peripheral Identifier */
-#define AT_XDMAC_CDS_MSP	0x2C	/* Channel Data Stride Memory Set Pattern */
-#define AT_XDMAC_CSUS		0x30	/* Channel Source Microblock Stride */
-#define AT_XDMAC_CDUS		0x34	/* Channel Destination Microblock Stride */
-
-#define AT_XDMAC_CHAN_REG_BASE	0x50	/* Channel registers base address */
-
-/* Microblock control members */
-#define AT_XDMAC_MBR_UBC_UBLEN_MAX	0xFFFFFFUL	/* Maximum Microblock Length */
-#define AT_XDMAC_MBR_UBC_NDE		(0x1 << 24)	/* Next Descriptor Enable */
-#define AT_XDMAC_MBR_UBC_NSEN		(0x1 << 25)	/* Next Descriptor Source Update */
-#define AT_XDMAC_MBR_UBC_NDEN		(0x1 << 26)	/* Next Descriptor Destination Update */
-#define AT_XDMAC_MBR_UBC_NDV0		(0x0 << 27)	/* Next Descriptor View 0 */
-#define AT_XDMAC_MBR_UBC_NDV1		(0x1 << 27)	/* Next Descriptor View 1 */
-#define AT_XDMAC_MBR_UBC_NDV2		(0x2 << 27)	/* Next Descriptor View 2 */
-#define AT_XDMAC_MBR_UBC_NDV3		(0x3 << 27)	/* Next Descriptor View 3 */
-
-#define AT_XDMAC_MAX_CHAN	0x20
-#define AT_XDMAC_MAX_CSIZE	16	/* 16 data */
-#define AT_XDMAC_MAX_DWIDTH	8	/* 64 bits */
-#define AT_XDMAC_RESIDUE_MAX_RETRIES	5
+#include "at_xdmac_regs.h"
 
 #define AT_XDMAC_DMA_BUSWIDTHS\
 	(BIT(DMA_SLAVE_BUSWIDTH_UNDEFINED) |\
drivers/dma/at_xdmac_regs.h new file +154 -0

154 lines not on this page · raw message

Signature · 1 line
2.25.1
#2 lore raw

Re: [PATCH 1/7] dmaengine: at_xdmac: separate register defines into header file

Hi, Eugen,

Quoted 10 lines · Eugen Hristev

Separate register defines into header file.
This is required to support a slightly different version of the register map in new hardware versions of the XDMAC.

---
 drivers/dma/at_xdmac.c      | 143 +--------------------------------
 drivers/dma/at_xdmac_regs.h | 154 ++++++++++++++++++++++++++++++++++++
 2 files changed, 155 insertions(+), 142 deletions(-)
 create mode 100644 drivers/dma/at_xdmac_regs.h

Even with the sama7g5 support there is a single .c file that includes the .h. I wouldn't split the registers definitions in a dedicated file.

Cheers,
ta
_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

#3 lore raw

PATCH 2/7 MAINTAINERS: add dma/at_xdmac_regs.h to XDMAC driver entry

In reply to Eugen Hristev

Add new header file for the at_xdmac regs definition to the proper MAINTAINERS entry.

---
 MAINTAINERS | 1 +
 1 file changed, 1 insertion(+)
MAINTAINERS +1 -0
index b5cfab015bd6..312ba6ae5fc7 100644
@@ -11361,6 +11361,7 @@ F:	Documentation/devicetree/bindings/dma/atmel-dma.txt
 F:	drivers/dma/at_hdmac.c
 F:	drivers/dma/at_hdmac_regs.h
 F:	drivers/dma/at_xdmac.c
+F:	drivers/dma/at_xdmac_regs.h
 F:	include/dt-bindings/dma/at91.h
 F:	include/linux/platform_data/dma-atmel.h
 
Signature · 7 lines
2.25.1


_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
#4 lore raw

Re: [PATCH 2/7] MAINTAINERS: add dma/at_xdmac_regs.h to XDMAC driver entry

Quoted 13 lines · Eugen Hristev

Add new header file for the at_xdmac regs definition to the proper MAINTAINERS entry.

---
 MAINTAINERS | 1 +
 1 file changed, 1 insertion(+)
MAINTAINERS +0 -0
index b5cfab015bd6..312ba6ae5fc7 100644

MAINTAINERS F: Documentation/devicetree/bindings/dma/atmel-dma.txt · line 11364

Quoted 4 lines
MAINTAINERS +1 -0
@@ -11361,6 +11361,7 @@ F:	Documentation/devicetree/bindings/dma/atmel-dma.txt
 F:	drivers/dma/at_hdmac.c
 F:	drivers/dma/at_hdmac_regs.h
 F:	drivers/dma/at_xdmac.c
+F:	drivers/dma/at_xdmac_regs.h

A dedicated entry for at_xdmac_regs.h will not be needed, but still we're here, let's shrink these lines to only one. A change like the one from below is welcomed:
+F: drivers/dma/at_*

ta

Quoted 4 lines
MAINTAINERS +0 -0
 F:	include/dt-bindings/dma/at91.h
 F:	include/linux/platform_data/dma-atmel.h
 
#5 lore raw

PATCH 3/7 dt-bindings: dmaengine: at_xdmac: add compatible with microchip,sama7g5

In reply to Eugen Hristev

Add compatible to sama7g5 SoC.

---
 Documentation/devicetree/bindings/dma/atmel-xdma.txt | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)
Documentation/devicetree/bindings/dma/atmel-xdma.txt +2 -1
index 4dc398e1a371..510b7f25ba24 100644
@@ -2,7 +2,8 @@
 
 * XDMA Controller
 Required properties:
-- compatible: Should be "atmel,sama5d4-dma" or "microchip,sam9x60-dma".
+- compatible: Should be "atmel,sama5d4-dma", "microchip,sam9x60-dma" or
+  "microchip,sama7g5-dma".
 - reg: Should contain DMA registers location and length.
 - interrupts: Should contain DMA interrupt.
 - #dma-cells: Must be <1>, used to represent the number of integer cells in
Signature · 1 line
2.25.1
#7 lore raw

PATCH 4/7 dmaengine: at_xdmac: adapt perid for mem2mem operations

In reply to Eugen Hristev

The PERID in the CC register for mem2mem operations must match an unused PERID.
The PERID field is 7 bits, but the selected value is 0x3f.
On later products we can have more reserved PERIDs for actual peripherals, thus this needs to be increased to maximum size.
Changing the value to 0x7f, which is the maximum for 7 bits field.

---
 drivers/dma/at_xdmac.c | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)
drivers/dma/at_xdmac.c +3 -3
index fab19e00a7be..81bb90206092 100644
@@ -726,7 +726,7 @@ at_xdmac_interleaved_queue_desc(struct dma_chan *chan,
 	 * match the one of another channel. If not, it could lead to spurious
 	 * flag status.
 	 */
-	u32			chan_cc = AT_XDMAC_CC_PERID(0x3f)
+	u32			chan_cc = AT_XDMAC_CC_PERID(0x7f)
 					| AT_XDMAC_CC_DIF(0)
 					| AT_XDMAC_CC_SIF(0)
 					| AT_XDMAC_CC_MBSIZE_SIXTEEN
@@ -908,7 +908,7 @@ at_xdmac_prep_dma_memcpy(struct dma_chan *chan, dma_addr_t dest, dma_addr_t src,
 	 * match the one of another channel. If not, it could lead to spurious
 	 * flag status.
 	 */
-	u32			chan_cc = AT_XDMAC_CC_PERID(0x3f)
+	u32			chan_cc = AT_XDMAC_CC_PERID(0x7f)
 					| AT_XDMAC_CC_DAM_INCREMENTED_AM
 					| AT_XDMAC_CC_SAM_INCREMENTED_AM
 					| AT_XDMAC_CC_DIF(0)
@@ -1014,7 +1014,7 @@ static struct at_xdmac_desc *at_xdmac_memset_create_desc(struct dma_chan *chan,
 	 * match the one of another channel. If not, it could lead to spurious
 	 * flag status.
 	 */
-	u32			chan_cc = AT_XDMAC_CC_PERID(0x3f)
+	u32			chan_cc = AT_XDMAC_CC_PERID(0x7f)
 					| AT_XDMAC_CC_DAM_UBS_AM
 					| AT_XDMAC_CC_SAM_INCREMENTED_AM
 					| AT_XDMAC_CC_DIF(0)
Signature · 7 lines
2.25.1


_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Reviewed-by on v1 4/7
#8 lore raw

Re: [PATCH 4/7] dmaengine: at_xdmac: adapt perid for mem2mem operations

Quoted 7 lines · Eugen Hristev

The PERID in the CC register for mem2mem operations must match an unused PERID.
The PERID field is 7 bits, but the selected value is 0x3f.
On later products we can have more reserved PERIDs for actual peripherals, thus this needs to be increased to maximum size.
Changing the value to 0x7f, which is the maximum for 7 bits field.

Maybe it is worth to explain that for memory-to-memory transfers, PERID should be set to an unused peripheral ID, and the maximum value seems the safest. Anyway with or without this addressed, one can add:

Quoted 37 lines
---
 drivers/dma/at_xdmac.c | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)
drivers/dma/at_xdmac.c +3 -3
index fab19e00a7be..81bb90206092 100644
@@ -726,7 +726,7 @@ at_xdmac_interleaved_queue_desc(struct dma_chan *chan,
 	 * match the one of another channel. If not, it could lead to spurious
 	 * flag status.
 	 */
-	u32			chan_cc = AT_XDMAC_CC_PERID(0x3f)
+	u32			chan_cc = AT_XDMAC_CC_PERID(0x7f)
 					| AT_XDMAC_CC_DIF(0)
 					| AT_XDMAC_CC_SIF(0)
 					| AT_XDMAC_CC_MBSIZE_SIXTEEN
@@ -908,7 +908,7 @@ at_xdmac_prep_dma_memcpy(struct dma_chan *chan, dma_addr_t dest, dma_addr_t src,
 	 * match the one of another channel. If not, it could lead to spurious
 	 * flag status.
 	 */
-	u32			chan_cc = AT_XDMAC_CC_PERID(0x3f)
+	u32			chan_cc = AT_XDMAC_CC_PERID(0x7f)
 					| AT_XDMAC_CC_DAM_INCREMENTED_AM
 					| AT_XDMAC_CC_SAM_INCREMENTED_AM
 					| AT_XDMAC_CC_DIF(0)
@@ -1014,7 +1014,7 @@ static struct at_xdmac_desc *at_xdmac_memset_create_desc(struct dma_chan *chan,
 	 * match the one of another channel. If not, it could lead to spurious
 	 * flag status.
 	 */
-	u32			chan_cc = AT_XDMAC_CC_PERID(0x3f)
+	u32			chan_cc = AT_XDMAC_CC_PERID(0x7f)
 					| AT_XDMAC_CC_DAM_UBS_AM
 					| AT_XDMAC_CC_SAM_INCREMENTED_AM
 					| AT_XDMAC_CC_DIF(0)
#9 lore raw

Re: [PATCH 4/7] dmaengine: at_xdmac: adapt perid for mem2mem operations

Quoted 9 lines · On 9/23/20 8:30 AM, Tudor Ambarus - M18064 wrote:
Quoted 7 lines · Eugen Hristev

The PERID in the CC register for mem2mem operations must match an unused PERID.
The PERID field is 7 bits, but the selected value is 0x3f.
On later products we can have more reserved PERIDs for actual peripherals, thus this needs to be increased to maximum size.
Changing the value to 0x7f, which is the maximum for 7 bits field.

Quoted 4 lines

Maybe it is worth to explain that for memory-to-memory transfers, PERID should be set to an unused peripheral ID, and the maximum value seems the safest. Anyway with or without this addressed, one can add:

:) I somehow misread your commit message, you already described that, it's fine.

Quoted 7 lines
Quoted 5 lines
---
 drivers/dma/at_xdmac.c | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)
#10 lore raw

PATCH 5/7 dmaengine: at_xdmac: add support for sama7g5 based at_xdmac

In reply to Eugen Hristev

SAMA7G5 SoC uses a slightly different variant of the AT_XDMAC. Added support by a new compatible and a layout struct that copes to the specific version considering the compatible string. Only the differences in register map are present in the layout struct. I reworked the register access for this part that has the differences. Also the Source/Destination Interface bits are no longer valid for this variant of the XDMAC. Thus, the layout also has a bool for specifying whether these bits are required or not.

---
 drivers/dma/at_xdmac.c      | 99 ++++++++++++++++++++++++++++++-------
 drivers/dma/at_xdmac_regs.h |  9 ----
 2 files changed, 82 insertions(+), 26 deletions(-)
drivers/dma/at_xdmac.c +82 -17
index 81bb90206092..874484a4e79f 100644
@@ -38,6 +38,27 @@ enum atc_status {
 	AT_XDMAC_CHAN_IS_PAUSED,
 };
 
+struct at_xdmac_layout {
+	/* Global Channel Read Suspend Register */
+	u8				grs;
+	/* Global Write Suspend Register */
+	u8				gws;
+	/* Global Channel Read Write Suspend Register */
+	u8				grws;
+	/* Global Channel Read Write Resume Register */
+	u8				grwr;
+	/* Global Channel Software Request Register */
+	u8				gswr;
+	/* Global channel Software Request Status Register */
+	u8				gsws;
+	/* Global Channel Software Flush Request Register */
+	u8				gswf;
+	/* Channel reg base */
+	u8				chan_cc_reg_base;
+	/* Source/Destination Interface must be specified or not */
+	bool				sdif;
+};
+
 /* ----- Channels ----- */
 struct at_xdmac_chan {
 	struct dma_chan			chan;
@@ -71,6 +92,7 @@ struct at_xdmac {
 	struct clk		*clk;
 	u32			save_gim;
 	struct dma_pool		*at_xdmac_desc_pool;
+	const struct at_xdmac_layout	*layout;
 	struct at_xdmac_chan	chan[];
 };
 
@@ -103,9 +125,33 @@ struct at_xdmac_desc {
 	struct list_head		xfer_node;
 } __aligned(sizeof(u64));
 
+static struct at_xdmac_layout at_xdmac_sama5d4_layout = {
+	.grs = 0x28,
+	.gws = 0x2C,
+	.grws = 0x30,
+	.grwr = 0x34,
+	.gswr = 0x38,
+	.gsws = 0x3C,
+	.gswf = 0x40,
+	.chan_cc_reg_base = 0x50,
+	.sdif = true,
+};
+
+static struct at_xdmac_layout at_xdmac_sama7g5_layout = {
+	.grs = 0x30,
+	.gws = 0x38,
+	.grws = 0x40,
+	.grwr = 0x44,
+	.gswr = 0x48,
+	.gsws = 0x4C,
+	.gswf = 0x50,
+	.chan_cc_reg_base = 0x60,
+	.sdif = false,
+};
+
 static inline void __iomem *at_xdmac_chan_reg_base(struct at_xdmac *atxdmac, unsigned int chan_nb)
 {
-	return atxdmac->regs + (AT_XDMAC_CHAN_REG_BASE + chan_nb * 0x40);
+	return atxdmac->regs + (atxdmac->layout->chan_cc_reg_base + chan_nb * 0x40);
 }
 
 #define at_xdmac_read(atxdmac, reg) readl_relaxed((atxdmac)->regs + (reg))
@@ -204,8 +250,10 @@ static void at_xdmac_start_xfer(struct at_xdmac_chan *atchan,
 	first->active_xfer = true;
 
 	/* Tell xdmac where to get the first descriptor. */
-	reg = AT_XDMAC_CNDA_NDA(first->tx_dma_desc.phys)
-	      | AT_XDMAC_CNDA_NDAIF(atchan->memif);
+	reg = AT_XDMAC_CNDA_NDA(first->tx_dma_desc.phys);
+	if (atxdmac->layout->sdif)
+		reg |= AT_XDMAC_CNDA_NDAIF(atchan->memif);
+
 	at_xdmac_chan_write(atchan, AT_XDMAC_CNDA, reg);
 
 	/*
@@ -400,6 +448,7 @@ static int at_xdmac_compute_chan_conf(struct dma_chan *chan,
 				      enum dma_transfer_direction direction)
 {
 	struct at_xdmac_chan	*atchan = to_at_xdmac_chan(chan);
+	struct at_xdmac		*atxdmac = to_at_xdmac(atchan->chan.device);
 	int			csize, dwidth;
 
 	if (direction == DMA_DEV_TO_MEM) {
@@ -407,12 +456,14 @@ static int at_xdmac_compute_chan_conf(struct dma_chan *chan,
 			AT91_XDMAC_DT_PERID(atchan->perid)
 			| AT_XDMAC_CC_DAM_INCREMENTED_AM
 			| AT_XDMAC_CC_SAM_FIXED_AM
-			| AT_XDMAC_CC_DIF(atchan->memif)
-			| AT_XDMAC_CC_SIF(atchan->perif)
 			| AT_XDMAC_CC_SWREQ_HWR_CONNECTED
 			| AT_XDMAC_CC_DSYNC_PER2MEM
 			| AT_XDMAC_CC_MBSIZE_SIXTEEN
 			| AT_XDMAC_CC_TYPE_PER_TRAN;
+		if (atxdmac->layout->sdif)
+			atchan->cfg |= AT_XDMAC_CC_DIF(atchan->memif)
+				| AT_XDMAC_CC_SIF(atchan->perif);
+
 		csize = ffs(atchan->sconfig.src_maxburst) - 1;
 		if (csize < 0) {
 			dev_err(chan2dev(chan), "invalid src maxburst value\n");
@@ -430,12 +481,14 @@ static int at_xdmac_compute_chan_conf(struct dma_chan *chan,
 			AT91_XDMAC_DT_PERID(atchan->perid)
 			| AT_XDMAC_CC_DAM_FIXED_AM
 			| AT_XDMAC_CC_SAM_INCREMENTED_AM
-			| AT_XDMAC_CC_DIF(atchan->perif)
-			| AT_XDMAC_CC_SIF(atchan->memif)
 			| AT_XDMAC_CC_SWREQ_HWR_CONNECTED
 			| AT_XDMAC_CC_DSYNC_MEM2PER
 			| AT_XDMAC_CC_MBSIZE_SIXTEEN
 			| AT_XDMAC_CC_TYPE_PER_TRAN;
+		if (atxdmac->layout->sdif)
+			atchan->cfg |=  AT_XDMAC_CC_DIF(atchan->perif)
+				| AT_XDMAC_CC_SIF(atchan->memif);
+
 		csize = ffs(atchan->sconfig.dst_maxburst) - 1;
 		if (csize < 0) {
 			dev_err(chan2dev(chan), "invalid src maxburst value\n");
@@ -711,6 +764,7 @@ at_xdmac_interleaved_queue_desc(struct dma_chan *chan,
 				struct data_chunk *chunk)
 {
 	struct at_xdmac_desc	*desc;
+	struct at_xdmac		*atxdmac = to_at_xdmac(atchan->chan.device);
 	u32			dwidth;
 	unsigned long		flags;
 	size_t			ublen;
@@ -727,10 +781,10 @@ at_xdmac_interleaved_queue_desc(struct dma_chan *chan,
 	 * flag status.
 	 */
 	u32			chan_cc = AT_XDMAC_CC_PERID(0x7f)
-					| AT_XDMAC_CC_DIF(0)
-					| AT_XDMAC_CC_SIF(0)
 					| AT_XDMAC_CC_MBSIZE_SIXTEEN
 					| AT_XDMAC_CC_TYPE_MEM_TRAN;
+	if (atxdmac->layout->sdif)
+		chan_cc |= AT_XDMAC_CC_DIF(0) | AT_XDMAC_CC_SIF(0);
 
 	dwidth = at_xdmac_align_width(chan, src | dst | chunk->size);
 	if (chunk->size >= (AT_XDMAC_MBR_UBC_UBLEN_MAX << dwidth)) {
@@ -893,6 +947,7 @@ at_xdmac_prep_dma_memcpy(struct dma_chan *chan, dma_addr_t dest, dma_addr_t src,
 			 size_t len, unsigned long flags)
 {
 	struct at_xdmac_chan	*atchan = to_at_xdmac_chan(chan);
+	struct at_xdmac		*atxdmac = to_at_xdmac(atchan->chan.device);
 	struct at_xdmac_desc	*first = NULL, *prev = NULL;
 	size_t			remaining_size = len, xfer_size = 0, ublen;
 	dma_addr_t		src_addr = src, dst_addr = dest;
@@ -911,12 +966,13 @@ at_xdmac_prep_dma_memcpy(struct dma_chan *chan, dma_addr_t dest, dma_addr_t src,
 	u32			chan_cc = AT_XDMAC_CC_PERID(0x7f)
 					| AT_XDMAC_CC_DAM_INCREMENTED_AM
 					| AT_XDMAC_CC_SAM_INCREMENTED_AM
-					| AT_XDMAC_CC_DIF(0)
-					| AT_XDMAC_CC_SIF(0)
 					| AT_XDMAC_CC_MBSIZE_SIXTEEN
 					| AT_XDMAC_CC_TYPE_MEM_TRAN;
 	unsigned long		irqflags;
 
+	if (atxdmac->layout->sdif)
+		chan_cc |= AT_XDMAC_CC_DIF(0) | AT_XDMAC_CC_SIF(0);
+
 	dev_dbg(chan2dev(chan), "%s: src=%pad, dest=%pad, len=%zd, flags=0x%lx\n",
 		__func__, &src, &dest, len, flags);
 
@@ -999,6 +1055,7 @@ static struct at_xdmac_desc *at_xdmac_memset_create_desc(struct dma_chan *chan,
 							 int value)
 {
 	struct at_xdmac_desc	*desc;
+	struct at_xdmac		*atxdmac = to_at_xdmac(atchan->chan.device);
 	unsigned long		flags;
 	size_t			ublen;
 	u32			dwidth;
@@ -1017,11 +1074,11 @@ static struct at_xdmac_desc *at_xdmac_memset_create_desc(struct dma_chan *chan,
 	u32			chan_cc = AT_XDMAC_CC_PERID(0x7f)
 					| AT_XDMAC_CC_DAM_UBS_AM
 					| AT_XDMAC_CC_SAM_INCREMENTED_AM
-					| AT_XDMAC_CC_DIF(0)
-					| AT_XDMAC_CC_SIF(0)
 					| AT_XDMAC_CC_MBSIZE_SIXTEEN
 					| AT_XDMAC_CC_MEMSET_HW_MODE
 					| AT_XDMAC_CC_TYPE_MEM_TRAN;
+	if (atxdmac->layout->sdif)
+		chan_cc |= AT_XDMAC_CC_DIF(0) | AT_XDMAC_CC_SIF(0);
 
 	dwidth = at_xdmac_align_width(chan, dst_addr);
 
@@ -1297,7 +1354,7 @@ at_xdmac_tx_status(struct dma_chan *chan, dma_cookie_t cookie,
 	mask = AT_XDMAC_CC_TYPE | AT_XDMAC_CC_DSYNC;
 	value = AT_XDMAC_CC_TYPE_PER_TRAN | AT_XDMAC_CC_DSYNC_PER2MEM;
 	if ((desc->lld.mbr_cfg & mask) == value) {
-		at_xdmac_write(atxdmac, AT_XDMAC_GSWF, atchan->mask);
+		at_xdmac_write(atxdmac, atxdmac->layout->gswf, atchan->mask);
 		while (!(at_xdmac_chan_read(atchan, AT_XDMAC_CIS) & AT_XDMAC_CIS_FIS))
 			cpu_relax();
 	}
@@ -1355,7 +1412,7 @@ at_xdmac_tx_status(struct dma_chan *chan, dma_cookie_t cookie,
 	 * FIFO flush ensures that data are really written.
 	 */
 	if ((desc->lld.mbr_cfg & mask) == value) {
-		at_xdmac_write(atxdmac, AT_XDMAC_GSWF, atchan->mask);
+		at_xdmac_write(atxdmac, atxdmac->layout->gswf, atchan->mask);
 		while (!(at_xdmac_chan_read(atchan, AT_XDMAC_CIS) & AT_XDMAC_CIS_FIS))
 			cpu_relax();
 	}
@@ -1620,7 +1677,7 @@ static int at_xdmac_device_pause(struct dma_chan *chan)
 		return 0;
 
 	spin_lock_irqsave(&atchan->lock, flags);
-	at_xdmac_write(atxdmac, AT_XDMAC_GRWS, atchan->mask);
+	at_xdmac_write(atxdmac, atxdmac->layout->grws, atchan->mask);
 	while (at_xdmac_chan_read(atchan, AT_XDMAC_CC)
 	       & (AT_XDMAC_CC_WRIP | AT_XDMAC_CC_RDIP))
 		cpu_relax();
@@ -1643,7 +1700,7 @@ static int at_xdmac_device_resume(struct dma_chan *chan)
 		return 0;
 	}
 
-	at_xdmac_write(atxdmac, AT_XDMAC_GRWR, atchan->mask);
+	at_xdmac_write(atxdmac, atxdmac->layout->grwr, atchan->mask);
 	clear_bit(AT_XDMAC_CHAN_IS_PAUSED, &atchan->status);
 	spin_unlock_irqrestore(&atchan->lock, flags);
 
@@ -1845,6 +1902,10 @@ static int at_xdmac_probe(struct platform_device *pdev)
 	atxdmac->regs = base;
 	atxdmac->irq = irq;
 
+	atxdmac->layout = of_device_get_match_data(&pdev->dev);
+	if (!atxdmac->layout)
+		return -ENODEV;
+
 	atxdmac->clk = devm_clk_get(&pdev->dev, "dma_clk");
 	if (IS_ERR(atxdmac->clk)) {
 		dev_err(&pdev->dev, "can't get dma_clk\n");
@@ -1988,6 +2049,10 @@ static const struct dev_pm_ops atmel_xdmac_dev_pm_ops = {
 static const struct of_device_id atmel_xdmac_dt_ids[] = {
 	{
 		.compatible = "atmel,sama5d4-dma",
+		.data = &at_xdmac_sama5d4_layout,
+	}, {
+		.compatible = "microchip,sama7g5-dma",
+		.data = &at_xdmac_sama7g5_layout,
 	}, {
 		/* sentinel */
 	}
drivers/dma/at_xdmac_regs.h +0 -9
index 3f7dda4c5743..7b4b4e24de70 100644
@@ -22,13 +22,6 @@
 #define AT_XDMAC_GE		0x1C	/* Global Channel Enable Register */
 #define AT_XDMAC_GD		0x20	/* Global Channel Disable Register */
 #define AT_XDMAC_GS		0x24	/* Global Channel Status Register */
-#define AT_XDMAC_GRS		0x28	/* Global Channel Read Suspend Register */
-#define AT_XDMAC_GWS		0x2C	/* Global Write Suspend Register */
-#define AT_XDMAC_GRWS		0x30	/* Global Channel Read Write Suspend Register */
-#define AT_XDMAC_GRWR		0x34	/* Global Channel Read Write Resume Register */
-#define AT_XDMAC_GSWR		0x38	/* Global Channel Software Request Register */
-#define AT_XDMAC_GSWS		0x3C	/* Global channel Software Request Status Register */
-#define AT_XDMAC_GSWF		0x40	/* Global Channel Software Flush Request Register */
 #define AT_XDMAC_VERSION	0xFFC	/* XDMAC Version Register */
 
 /* Channel relative registers offsets */
@@ -134,8 +127,6 @@
 #define AT_XDMAC_CSUS		0x30	/* Channel Source Microblock Stride */
 #define AT_XDMAC_CDUS		0x34	/* Channel Destination Microblock Stride */
 
-#define AT_XDMAC_CHAN_REG_BASE	0x50	/* Channel registers base address */
-
 /* Microblock control members */
 #define AT_XDMAC_MBR_UBC_UBLEN_MAX	0xFFFFFFUL	/* Maximum Microblock Length */
 #define AT_XDMAC_MBR_UBC_NDE		(0x1 << 24)	/* Next Descriptor Enable */
Signature · 1 line
2.25.1
Reviewed-by on v1 5/7
#11 lore raw

Re: [PATCH 5/7] dmaengine: at_xdmac: add support for sama7g5 based at_xdmac

Quoted 56 lines · Eugen Hristev

SAMA7G5 SoC uses a slightly different variant of the AT_XDMAC. Added support by a new compatible and a layout struct that copes to the specific version considering the compatible string. Only the differences in register map are present in the layout struct. I reworked the register access for this part that has the differences. Also the Source/Destination Interface bits are no longer valid for this variant of the XDMAC. Thus, the layout also has a bool for specifying whether these bits are required or not.

---
 drivers/dma/at_xdmac.c      | 99 ++++++++++++++++++++++++++++++-------
 drivers/dma/at_xdmac_regs.h |  9 ----
 2 files changed, 82 insertions(+), 26 deletions(-)
drivers/dma/at_xdmac.c +22 -0
index 81bb90206092..874484a4e79f 100644
@@ -38,6 +38,27 @@ enum atc_status {
 	AT_XDMAC_CHAN_IS_PAUSED,
 };
 
+struct at_xdmac_layout {
+	/* Global Channel Read Suspend Register */
+	u8				grs;
+	/* Global Write Suspend Register */
+	u8				gws;
+	/* Global Channel Read Write Suspend Register */
+	u8				grws;
+	/* Global Channel Read Write Resume Register */
+	u8				grwr;
+	/* Global Channel Software Request Register */
+	u8				gswr;
+	/* Global channel Software Request Status Register */
+	u8				gsws;
+	/* Global Channel Software Flush Request Register */
+	u8				gswf;
+	/* Channel reg base */
+	u8				chan_cc_reg_base;
+	/* Source/Destination Interface must be specified or not */
+	bool				sdif;
+};
+
 /* ----- Channels ----- */
 struct at_xdmac_chan {
 	struct dma_chan			chan;
@@ -71,6 +92,7 @@ struct at_xdmac {
 	struct clk		*clk;
 	u32			save_gim;
 	struct dma_pool		*at_xdmac_desc_pool;
+	const struct at_xdmac_layout	*layout;
 	struct at_xdmac_chan	chan[];
 };
 

drivers/dma/at_xdmac.c struct at_xdmac_desc { · line 128

Quoted 4 lines
drivers/dma/at_xdmac.c +1 -0
@@ -103,9 +125,33 @@ struct at_xdmac_desc {
 	struct list_head		xfer_node;
 } __aligned(sizeof(u64));
 
+static struct at_xdmac_layout at_xdmac_sama5d4_layout = {

static const struct

drivers/dma/at_xdmac.c struct at_xdmac_desc { · line 140

Quoted 12 lines
drivers/dma/at_xdmac.c +12 -0
+	.grs = 0x28,
+	.gws = 0x2C,
+	.grws = 0x30,
+	.grwr = 0x34,
+	.gswr = 0x38,
+	.gsws = 0x3C,
+	.gswf = 0x40,
+	.chan_cc_reg_base = 0x50,
+	.sdif = true,
+};
+
+static struct at_xdmac_layout at_xdmac_sama7g5_layout = {

static const struct

drivers/dma/at_xdmac.c struct at_xdmac_desc { · line 148

Quoted 8 lines
drivers/dma/at_xdmac.c +8 -0
+	.grs = 0x30,
+	.gws = 0x38,
+	.grws = 0x40,
+	.grwr = 0x44,
+	.gswr = 0x48,
+	.gsws = 0x4C,
+	.gswf = 0x50,
+	.chan_cc_reg_base = 0x60,

one may find these plain offsets as too raw and probably prefer some defines for them, but I too think that the members of the struct are self-explanatory, so I'm ok either way.

Quoted 34 lines
drivers/dma/at_xdmac.c +9 -3
+	.sdif = false,
+};
+
 static inline void __iomem *at_xdmac_chan_reg_base(struct at_xdmac *atxdmac, unsigned int chan_nb)
 {
-	return atxdmac->regs + (AT_XDMAC_CHAN_REG_BASE + chan_nb * 0x40);
+	return atxdmac->regs + (atxdmac->layout->chan_cc_reg_base + chan_nb * 0x40);
 }
 
 #define at_xdmac_read(atxdmac, reg) readl_relaxed((atxdmac)->regs + (reg))
@@ -204,8 +250,10 @@ static void at_xdmac_start_xfer(struct at_xdmac_chan *atchan,
 	first->active_xfer = true;
 
 	/* Tell xdmac where to get the first descriptor. */
-	reg = AT_XDMAC_CNDA_NDA(first->tx_dma_desc.phys)
-	      | AT_XDMAC_CNDA_NDAIF(atchan->memif);
+	reg = AT_XDMAC_CNDA_NDA(first->tx_dma_desc.phys);
+	if (atxdmac->layout->sdif)
+		reg |= AT_XDMAC_CNDA_NDAIF(atchan->memif);
+
 	at_xdmac_chan_write(atchan, AT_XDMAC_CNDA, reg);
 
 	/*
@@ -400,6 +448,7 @@ static int at_xdmac_compute_chan_conf(struct dma_chan *chan,
 				      enum dma_transfer_direction direction)
 {
 	struct at_xdmac_chan	*atchan = to_at_xdmac_chan(chan);
+	struct at_xdmac		*atxdmac = to_at_xdmac(atchan->chan.device);
 	int			csize, dwidth;
 
 	if (direction == DMA_DEV_TO_MEM) {
@@ -407,12 +456,14 @@ static int at_xdmac_compute_chan_conf(struct dma_chan *chan,
 			AT91_XDMAC_DT_PERID(atchan->perid)
 			| AT_XDMAC_CC_DAM_INCREMENTED_AM

drivers/dma/at_xdmac.c static int at_xdmac_compute_chan_conf(struct dma_chan *chan, · line 465

Quoted 10 lines
drivers/dma/at_xdmac.c +3 -2
 			| AT_XDMAC_CC_SAM_FIXED_AM
-			| AT_XDMAC_CC_DIF(atchan->memif)
-			| AT_XDMAC_CC_SIF(atchan->perif)
 			| AT_XDMAC_CC_SWREQ_HWR_CONNECTED
 			| AT_XDMAC_CC_DSYNC_PER2MEM
 			| AT_XDMAC_CC_MBSIZE_SIXTEEN
 			| AT_XDMAC_CC_TYPE_PER_TRAN;
+		if (atxdmac->layout->sdif)
+			atchan->cfg |= AT_XDMAC_CC_DIF(atchan->memif)
+				| AT_XDMAC_CC_SIF(atchan->perif);

very odd for me to see the "|" operator on the next line. I find it hard to read and somehow exhausting. I would put it on the first line even if throughout the driver it's on the next line.

Quoted 30 lines
drivers/dma/at_xdmac.c +6 -2
+
 		csize = ffs(atchan->sconfig.src_maxburst) - 1;
 		if (csize < 0) {
 			dev_err(chan2dev(chan), "invalid src maxburst value\n");
@@ -430,12 +481,14 @@ static int at_xdmac_compute_chan_conf(struct dma_chan *chan,
 			AT91_XDMAC_DT_PERID(atchan->perid)
 			| AT_XDMAC_CC_DAM_FIXED_AM
 			| AT_XDMAC_CC_SAM_INCREMENTED_AM
-			| AT_XDMAC_CC_DIF(atchan->perif)
-			| AT_XDMAC_CC_SIF(atchan->memif)
 			| AT_XDMAC_CC_SWREQ_HWR_CONNECTED
 			| AT_XDMAC_CC_DSYNC_MEM2PER
 			| AT_XDMAC_CC_MBSIZE_SIXTEEN
 			| AT_XDMAC_CC_TYPE_PER_TRAN;
+		if (atxdmac->layout->sdif)
+			atchan->cfg |=  AT_XDMAC_CC_DIF(atchan->perif)
+				| AT_XDMAC_CC_SIF(atchan->memif);
+
 		csize = ffs(atchan->sconfig.dst_maxburst) - 1;
 		if (csize < 0) {
 			dev_err(chan2dev(chan), "invalid src maxburst value\n");
@@ -711,6 +764,7 @@ at_xdmac_interleaved_queue_desc(struct dma_chan *chan,
 				struct data_chunk *chunk)
 {
 	struct at_xdmac_desc	*desc;
+	struct at_xdmac		*atxdmac = to_at_xdmac(atchan->chan.device);
 	u32			dwidth;
 	unsigned long		flags;
 	size_t			ublen;

drivers/dma/at_xdmac.c at_xdmac_interleaved_queue_desc(struct dma_chan *chan, · line 787

Quoted 9 lines
drivers/dma/at_xdmac.c +2 -2
@@ -727,10 +781,10 @@ at_xdmac_interleaved_queue_desc(struct dma_chan *chan,
 	 * flag status.
 	 */
 	u32			chan_cc = AT_XDMAC_CC_PERID(0x7f)
-					| AT_XDMAC_CC_DIF(0)
-					| AT_XDMAC_CC_SIF(0)
 					| AT_XDMAC_CC_MBSIZE_SIXTEEN
 					| AT_XDMAC_CC_TYPE_MEM_TRAN;
+	if (atxdmac->layout->sdif)
+		chan_cc |= AT_XDMAC_CC_DIF(0) | AT_XDMAC_CC_SIF(0);

there is a comment above chan_cc init that explains that we have to use interface 0 for both source and destination, so maybe we can get rid of this explicit OR with zero and update the comment for sama7g5 case.

Quoted 13 lines
drivers/dma/at_xdmac.c +1 -0
 	dwidth = at_xdmac_align_width(chan, src | dst | chunk->size);
 	if (chunk->size >= (AT_XDMAC_MBR_UBC_UBLEN_MAX << dwidth)) {
@@ -893,6 +947,7 @@ at_xdmac_prep_dma_memcpy(struct dma_chan *chan, dma_addr_t dest, dma_addr_t src,
 			 size_t len, unsigned long flags)
 {
 	struct at_xdmac_chan	*atchan = to_at_xdmac_chan(chan);
+	struct at_xdmac		*atxdmac = to_at_xdmac(atchan->chan.device);
 	struct at_xdmac_desc	*first = NULL, *prev = NULL;
 	size_t			remaining_size = len, xfer_size = 0, ublen;
 	dma_addr_t		src_addr = src, dst_addr = dest;
@@ -911,12 +966,13 @@ at_xdmac_prep_dma_memcpy(struct dma_chan *chan, dma_addr_t dest, dma_addr_t src,
 	u32			chan_cc = AT_XDMAC_CC_PERID(0x7f)

drivers/dma/at_xdmac.c at_xdmac_prep_dma_memcpy(struct dma_chan *chan, dma_addr_t dest, dma_addr_t src, · line 974

Quoted 10 lines
drivers/dma/at_xdmac.c +2 -2
 					| AT_XDMAC_CC_DAM_INCREMENTED_AM
 					| AT_XDMAC_CC_SAM_INCREMENTED_AM
-					| AT_XDMAC_CC_DIF(0)
-					| AT_XDMAC_CC_SIF(0)
 					| AT_XDMAC_CC_MBSIZE_SIXTEEN
 					| AT_XDMAC_CC_TYPE_MEM_TRAN;
 	unsigned long		irqflags;
 
+	if (atxdmac->layout->sdif)
+		chan_cc |= AT_XDMAC_CC_DIF(0) | AT_XDMAC_CC_SIF(0);

same here

Quoted 13 lines
drivers/dma/at_xdmac.c +2 -0
+
 	dev_dbg(chan2dev(chan), "%s: src=%pad, dest=%pad, len=%zd, flags=0x%lx\n",
 		__func__, &src, &dest, len, flags);
 
@@ -999,6 +1055,7 @@ static struct at_xdmac_desc *at_xdmac_memset_create_desc(struct dma_chan *chan,
 							 int value)
 {
 	struct at_xdmac_desc	*desc;
+	struct at_xdmac		*atxdmac = to_at_xdmac(atchan->chan.device);
 	unsigned long		flags;
 	size_t			ublen;
 	u32			dwidth;

drivers/dma/at_xdmac.c static struct at_xdmac_desc *at_xdmac_memset_create_desc(struct dma_chan *chan, · line 1081

Quoted 10 lines
drivers/dma/at_xdmac.c +2 -2
@@ -1017,11 +1074,11 @@ static struct at_xdmac_desc *at_xdmac_memset_create_desc(struct dma_chan *chan,
 	u32			chan_cc = AT_XDMAC_CC_PERID(0x7f)
 					| AT_XDMAC_CC_DAM_UBS_AM
 					| AT_XDMAC_CC_SAM_INCREMENTED_AM
-					| AT_XDMAC_CC_DIF(0)
-					| AT_XDMAC_CC_SIF(0)
 					| AT_XDMAC_CC_MBSIZE_SIXTEEN
 					| AT_XDMAC_CC_MEMSET_HW_MODE
 					| AT_XDMAC_CC_TYPE_MEM_TRAN;
+	if (atxdmac->layout->sdif)
+		chan_cc |= AT_XDMAC_CC_DIF(0) | AT_XDMAC_CC_SIF(0);

same here

Quoted 40 lines
drivers/dma/at_xdmac.c +4 -4
 	dwidth = at_xdmac_align_width(chan, dst_addr);
 
@@ -1297,7 +1354,7 @@ at_xdmac_tx_status(struct dma_chan *chan, dma_cookie_t cookie,
 	mask = AT_XDMAC_CC_TYPE | AT_XDMAC_CC_DSYNC;
 	value = AT_XDMAC_CC_TYPE_PER_TRAN | AT_XDMAC_CC_DSYNC_PER2MEM;
 	if ((desc->lld.mbr_cfg & mask) == value) {
-		at_xdmac_write(atxdmac, AT_XDMAC_GSWF, atchan->mask);
+		at_xdmac_write(atxdmac, atxdmac->layout->gswf, atchan->mask);
 		while (!(at_xdmac_chan_read(atchan, AT_XDMAC_CIS) & AT_XDMAC_CIS_FIS))
 			cpu_relax();
 	}
@@ -1355,7 +1412,7 @@ at_xdmac_tx_status(struct dma_chan *chan, dma_cookie_t cookie,
 	 * FIFO flush ensures that data are really written.
 	 */
 	if ((desc->lld.mbr_cfg & mask) == value) {
-		at_xdmac_write(atxdmac, AT_XDMAC_GSWF, atchan->mask);
+		at_xdmac_write(atxdmac, atxdmac->layout->gswf, atchan->mask);
 		while (!(at_xdmac_chan_read(atchan, AT_XDMAC_CIS) & AT_XDMAC_CIS_FIS))
 			cpu_relax();
 	}
@@ -1620,7 +1677,7 @@ static int at_xdmac_device_pause(struct dma_chan *chan)
 		return 0;
 
 	spin_lock_irqsave(&atchan->lock, flags);
-	at_xdmac_write(atxdmac, AT_XDMAC_GRWS, atchan->mask);
+	at_xdmac_write(atxdmac, atxdmac->layout->grws, atchan->mask);
 	while (at_xdmac_chan_read(atchan, AT_XDMAC_CC)
 	       & (AT_XDMAC_CC_WRIP | AT_XDMAC_CC_RDIP))
 		cpu_relax();
@@ -1643,7 +1700,7 @@ static int at_xdmac_device_resume(struct dma_chan *chan)
 		return 0;
 	}
 
-	at_xdmac_write(atxdmac, AT_XDMAC_GRWR, atchan->mask);
+	at_xdmac_write(atxdmac, atxdmac->layout->grwr, atchan->mask);
 	clear_bit(AT_XDMAC_CHAN_IS_PAUSED, &atchan->status);
 	spin_unlock_irqrestore(&atchan->lock, flags);
 

drivers/dma/at_xdmac.c static int at_xdmac_probe(struct platform_device *pdev) · line 1907

Quoted 6 lines
drivers/dma/at_xdmac.c +3 -0
@@ -1845,6 +1902,10 @@ static int at_xdmac_probe(struct platform_device *pdev)
 	atxdmac->regs = base;
 	atxdmac->irq = irq;
 
+	atxdmac->layout = of_device_get_match_data(&pdev->dev);
+	if (!atxdmac->layout)
+		return -ENODEV;

I would get the data upper in the function, after getting irq. If data is not provided, you would spare some ops that will be done gratuitously.

With these addressed one may add:

Quoted 43 lines
drivers/dma/at_xdmac.c +5 -0
+
 	atxdmac->clk = devm_clk_get(&pdev->dev, "dma_clk");
 	if (IS_ERR(atxdmac->clk)) {
 		dev_err(&pdev->dev, "can't get dma_clk\n");
@@ -1988,6 +2049,10 @@ static const struct dev_pm_ops atmel_xdmac_dev_pm_ops = {
 static const struct of_device_id atmel_xdmac_dt_ids[] = {
 	{
 		.compatible = "atmel,sama5d4-dma",
+		.data = &at_xdmac_sama5d4_layout,
+	}, {
+		.compatible = "microchip,sama7g5-dma",
+		.data = &at_xdmac_sama7g5_layout,
 	}, {
 		/* sentinel */
 	}
drivers/dma/at_xdmac_regs.h +0 -9
index 3f7dda4c5743..7b4b4e24de70 100644
@@ -22,13 +22,6 @@
 #define AT_XDMAC_GE		0x1C	/* Global Channel Enable Register */
 #define AT_XDMAC_GD		0x20	/* Global Channel Disable Register */
 #define AT_XDMAC_GS		0x24	/* Global Channel Status Register */
-#define AT_XDMAC_GRS		0x28	/* Global Channel Read Suspend Register */
-#define AT_XDMAC_GWS		0x2C	/* Global Write Suspend Register */
-#define AT_XDMAC_GRWS		0x30	/* Global Channel Read Write Suspend Register */
-#define AT_XDMAC_GRWR		0x34	/* Global Channel Read Write Resume Register */
-#define AT_XDMAC_GSWR		0x38	/* Global Channel Software Request Register */
-#define AT_XDMAC_GSWS		0x3C	/* Global channel Software Request Status Register */
-#define AT_XDMAC_GSWF		0x40	/* Global Channel Software Flush Request Register */
 #define AT_XDMAC_VERSION	0xFFC	/* XDMAC Version Register */
 
 /* Channel relative registers offsets */
@@ -134,8 +127,6 @@
 #define AT_XDMAC_CSUS		0x30	/* Channel Source Microblock Stride */
 #define AT_XDMAC_CDUS		0x34	/* Channel Destination Microblock Stride */
 
-#define AT_XDMAC_CHAN_REG_BASE	0x50	/* Channel registers base address */
-
 /* Microblock control members */
 #define AT_XDMAC_MBR_UBC_UBLEN_MAX	0xFFFFFFUL	/* Maximum Microblock Length */
 #define AT_XDMAC_MBR_UBC_NDE		(0x1 << 24)	/* Next Descriptor Enable */
#12 lore raw

Re: [PATCH 5/7] dmaengine: at_xdmac: add support for sama7g5 based at_xdmac

Quoted 280 lines · On 23.09.2020 10:08, Tudor Ambarus - M18064 wrote:
Quoted 56 lines · Eugen Hristev

SAMA7G5 SoC uses a slightly different variant of the AT_XDMAC. Added support by a new compatible and a layout struct that copes to the specific version considering the compatible string. Only the differences in register map are present in the layout struct. I reworked the register access for this part that has the differences. Also the Source/Destination Interface bits are no longer valid for this variant of the XDMAC. Thus, the layout also has a bool for specifying whether these bits are required or not.

---
  drivers/dma/at_xdmac.c      | 99 ++++++++++++++++++++++++++++++-------
  drivers/dma/at_xdmac_regs.h |  9 ----
  2 files changed, 82 insertions(+), 26 deletions(-)
drivers/dma/at_xdmac.c +22 -0
index 81bb90206092..874484a4e79f 100644
@@ -38,6 +38,27 @@ enum atc_status {
  	AT_XDMAC_CHAN_IS_PAUSED,
  };
 
+struct at_xdmac_layout {
+	/* Global Channel Read Suspend Register */
+	u8				grs;
+	/* Global Write Suspend Register */
+	u8				gws;
+	/* Global Channel Read Write Suspend Register */
+	u8				grws;
+	/* Global Channel Read Write Resume Register */
+	u8				grwr;
+	/* Global Channel Software Request Register */
+	u8				gswr;
+	/* Global channel Software Request Status Register */
+	u8				gsws;
+	/* Global Channel Software Flush Request Register */
+	u8				gswf;
+	/* Channel reg base */
+	u8				chan_cc_reg_base;
+	/* Source/Destination Interface must be specified or not */
+	bool				sdif;
+};
+
  /* ----- Channels ----- */
  struct at_xdmac_chan {
  	struct dma_chan			chan;
@@ -71,6 +92,7 @@ struct at_xdmac {
  	struct clk		*clk;
  	u32			save_gim;
  	struct dma_pool		*at_xdmac_desc_pool;
+	const struct at_xdmac_layout	*layout;
  	struct at_xdmac_chan	chan[];
  };
 

drivers/dma/at_xdmac.c struct at_xdmac_desc { · line 128

Quoted 4 lines
drivers/dma/at_xdmac.c +1 -0
@@ -103,9 +125,33 @@ struct at_xdmac_desc {
  	struct list_head		xfer_node;
  } __aligned(sizeof(u64));
 
+static struct at_xdmac_layout at_xdmac_sama5d4_layout = {

static const struct

drivers/dma/at_xdmac.c struct at_xdmac_desc { · line 140

Quoted 12 lines
drivers/dma/at_xdmac.c +12 -0
+	.grs = 0x28,
+	.gws = 0x2C,
+	.grws = 0x30,
+	.grwr = 0x34,
+	.gswr = 0x38,
+	.gsws = 0x3C,
+	.gswf = 0x40,
+	.chan_cc_reg_base = 0x50,
+	.sdif = true,
+};
+
+static struct at_xdmac_layout at_xdmac_sama7g5_layout = {

static const struct

drivers/dma/at_xdmac.c struct at_xdmac_desc { · line 148

Quoted 8 lines
drivers/dma/at_xdmac.c +8 -0
+	.grs = 0x30,
+	.gws = 0x38,
+	.grws = 0x40,
+	.grwr = 0x44,
+	.gswr = 0x48,
+	.gsws = 0x4C,
+	.gswf = 0x50,
+	.chan_cc_reg_base = 0x60,

one may find these plain offsets as too raw and probably prefer some defines for them, but I too think that the members of the struct are self-explanatory, so I'm ok either way.

Quoted 34 lines
drivers/dma/at_xdmac.c +9 -3
+	.sdif = false,
+};
+
  static inline void __iomem *at_xdmac_chan_reg_base(struct at_xdmac *atxdmac, unsigned int chan_nb)
  {
-	return atxdmac->regs + (AT_XDMAC_CHAN_REG_BASE + chan_nb * 0x40);
+	return atxdmac->regs + (atxdmac->layout->chan_cc_reg_base + chan_nb * 0x40);
  }
 
  #define at_xdmac_read(atxdmac, reg) readl_relaxed((atxdmac)->regs + (reg))
@@ -204,8 +250,10 @@ static void at_xdmac_start_xfer(struct at_xdmac_chan *atchan,
  	first->active_xfer = true;
 
  	/* Tell xdmac where to get the first descriptor. */
-	reg = AT_XDMAC_CNDA_NDA(first->tx_dma_desc.phys)
-	      | AT_XDMAC_CNDA_NDAIF(atchan->memif);
+	reg = AT_XDMAC_CNDA_NDA(first->tx_dma_desc.phys);
+	if (atxdmac->layout->sdif)
+		reg |= AT_XDMAC_CNDA_NDAIF(atchan->memif);
+
  	at_xdmac_chan_write(atchan, AT_XDMAC_CNDA, reg);
 
  	/*
@@ -400,6 +448,7 @@ static int at_xdmac_compute_chan_conf(struct dma_chan *chan,
  				      enum dma_transfer_direction direction)
  {
  	struct at_xdmac_chan	*atchan = to_at_xdmac_chan(chan);
+	struct at_xdmac		*atxdmac = to_at_xdmac(atchan->chan.device);
  	int			csize, dwidth;
 
  	if (direction == DMA_DEV_TO_MEM) {
@@ -407,12 +456,14 @@ static int at_xdmac_compute_chan_conf(struct dma_chan *chan,
  			AT91_XDMAC_DT_PERID(atchan->perid)
  			| AT_XDMAC_CC_DAM_INCREMENTED_AM

drivers/dma/at_xdmac.c static int at_xdmac_compute_chan_conf(struct dma_chan *chan, · line 465

Quoted 10 lines
drivers/dma/at_xdmac.c +3 -2
  			| AT_XDMAC_CC_SAM_FIXED_AM
-			| AT_XDMAC_CC_DIF(atchan->memif)
-			| AT_XDMAC_CC_SIF(atchan->perif)
  			| AT_XDMAC_CC_SWREQ_HWR_CONNECTED
  			| AT_XDMAC_CC_DSYNC_PER2MEM
  			| AT_XDMAC_CC_MBSIZE_SIXTEEN
  			| AT_XDMAC_CC_TYPE_PER_TRAN;
+		if (atxdmac->layout->sdif)
+			atchan->cfg |= AT_XDMAC_CC_DIF(atchan->memif)
+				| AT_XDMAC_CC_SIF(atchan->perif);

very odd for me to see the "|" operator on the next line. I find it hard to read and somehow exhausting. I would put it on the first line even if throughout the driver it's on the next line.

Quoted 30 lines
drivers/dma/at_xdmac.c +6 -2
+
  		csize = ffs(atchan->sconfig.src_maxburst) - 1;
  		if (csize < 0) {
  			dev_err(chan2dev(chan), "invalid src maxburst value\n");
@@ -430,12 +481,14 @@ static int at_xdmac_compute_chan_conf(struct dma_chan *chan,
  			AT91_XDMAC_DT_PERID(atchan->perid)
  			| AT_XDMAC_CC_DAM_FIXED_AM
  			| AT_XDMAC_CC_SAM_INCREMENTED_AM
-			| AT_XDMAC_CC_DIF(atchan->perif)
-			| AT_XDMAC_CC_SIF(atchan->memif)
  			| AT_XDMAC_CC_SWREQ_HWR_CONNECTED
  			| AT_XDMAC_CC_DSYNC_MEM2PER
  			| AT_XDMAC_CC_MBSIZE_SIXTEEN
  			| AT_XDMAC_CC_TYPE_PER_TRAN;
+		if (atxdmac->layout->sdif)
+			atchan->cfg |=  AT_XDMAC_CC_DIF(atchan->perif)
+				| AT_XDMAC_CC_SIF(atchan->memif);
+
  		csize = ffs(atchan->sconfig.dst_maxburst) - 1;
  		if (csize < 0) {
  			dev_err(chan2dev(chan), "invalid src maxburst value\n");
@@ -711,6 +764,7 @@ at_xdmac_interleaved_queue_desc(struct dma_chan *chan,
  				struct data_chunk *chunk)
  {
  	struct at_xdmac_desc	*desc;
+	struct at_xdmac		*atxdmac = to_at_xdmac(atchan->chan.device);
  	u32			dwidth;
  	unsigned long		flags;
  	size_t			ublen;

drivers/dma/at_xdmac.c at_xdmac_interleaved_queue_desc(struct dma_chan *chan, · line 787

Quoted 9 lines
drivers/dma/at_xdmac.c +2 -2
@@ -727,10 +781,10 @@ at_xdmac_interleaved_queue_desc(struct dma_chan *chan,
  	 * flag status.
  	 */
  	u32			chan_cc = AT_XDMAC_CC_PERID(0x7f)
-					| AT_XDMAC_CC_DIF(0)
-					| AT_XDMAC_CC_SIF(0)
  					| AT_XDMAC_CC_MBSIZE_SIXTEEN
  					| AT_XDMAC_CC_TYPE_MEM_TRAN;
+	if (atxdmac->layout->sdif)
+		chan_cc |= AT_XDMAC_CC_DIF(0) | AT_XDMAC_CC_SIF(0);

there is a comment above chan_cc init that explains that we have to use interface 0 for both source and destination, so maybe we can get rid of this explicit OR with zero and update the comment for sama7g5 case.

Quoted 13 lines
drivers/dma/at_xdmac.c +1 -0
  	dwidth = at_xdmac_align_width(chan, src | dst | chunk->size);
  	if (chunk->size >= (AT_XDMAC_MBR_UBC_UBLEN_MAX << dwidth)) {
@@ -893,6 +947,7 @@ at_xdmac_prep_dma_memcpy(struct dma_chan *chan, dma_addr_t dest, dma_addr_t src,
  			 size_t len, unsigned long flags)
  {
  	struct at_xdmac_chan	*atchan = to_at_xdmac_chan(chan);
+	struct at_xdmac		*atxdmac = to_at_xdmac(atchan->chan.device);
  	struct at_xdmac_desc	*first = NULL, *prev = NULL;
  	size_t			remaining_size = len, xfer_size = 0, ublen;
  	dma_addr_t		src_addr = src, dst_addr = dest;
@@ -911,12 +966,13 @@ at_xdmac_prep_dma_memcpy(struct dma_chan *chan, dma_addr_t dest, dma_addr_t src,
  	u32			chan_cc = AT_XDMAC_CC_PERID(0x7f)

drivers/dma/at_xdmac.c at_xdmac_prep_dma_memcpy(struct dma_chan *chan, dma_addr_t dest, dma_addr_t src, · line 974

Quoted 10 lines
drivers/dma/at_xdmac.c +2 -2
  					| AT_XDMAC_CC_DAM_INCREMENTED_AM
  					| AT_XDMAC_CC_SAM_INCREMENTED_AM
-					| AT_XDMAC_CC_DIF(0)
-					| AT_XDMAC_CC_SIF(0)
  					| AT_XDMAC_CC_MBSIZE_SIXTEEN
  					| AT_XDMAC_CC_TYPE_MEM_TRAN;
  	unsigned long		irqflags;
 
+	if (atxdmac->layout->sdif)
+		chan_cc |= AT_XDMAC_CC_DIF(0) | AT_XDMAC_CC_SIF(0);

same here

Quoted 13 lines
drivers/dma/at_xdmac.c +2 -0
+
  	dev_dbg(chan2dev(chan), "%s: src=%pad, dest=%pad, len=%zd, flags=0x%lx\n",
  		__func__, &src, &dest, len, flags);
 
@@ -999,6 +1055,7 @@ static struct at_xdmac_desc *at_xdmac_memset_create_desc(struct dma_chan *chan,
  							 int value)
  {
  	struct at_xdmac_desc	*desc;
+	struct at_xdmac		*atxdmac = to_at_xdmac(atchan->chan.device);
  	unsigned long		flags;
  	size_t			ublen;
  	u32			dwidth;

drivers/dma/at_xdmac.c static struct at_xdmac_desc *at_xdmac_memset_create_desc(struct dma_chan *chan, · line 1081

Quoted 10 lines
drivers/dma/at_xdmac.c +2 -2
@@ -1017,11 +1074,11 @@ static struct at_xdmac_desc *at_xdmac_memset_create_desc(struct dma_chan *chan,
  	u32			chan_cc = AT_XDMAC_CC_PERID(0x7f)
  					| AT_XDMAC_CC_DAM_UBS_AM
  					| AT_XDMAC_CC_SAM_INCREMENTED_AM
-					| AT_XDMAC_CC_DIF(0)
-					| AT_XDMAC_CC_SIF(0)
  					| AT_XDMAC_CC_MBSIZE_SIXTEEN
  					| AT_XDMAC_CC_MEMSET_HW_MODE
  					| AT_XDMAC_CC_TYPE_MEM_TRAN;
+	if (atxdmac->layout->sdif)
+		chan_cc |= AT_XDMAC_CC_DIF(0) | AT_XDMAC_CC_SIF(0);

same here

Quoted 43 lines
drivers/dma/at_xdmac.c +4 -4
  	dwidth = at_xdmac_align_width(chan, dst_addr);
 
@@ -1297,7 +1354,7 @@ at_xdmac_tx_status(struct dma_chan *chan, dma_cookie_t cookie,
  	mask = AT_XDMAC_CC_TYPE | AT_XDMAC_CC_DSYNC;
  	value = AT_XDMAC_CC_TYPE_PER_TRAN | AT_XDMAC_CC_DSYNC_PER2MEM;
  	if ((desc->lld.mbr_cfg & mask) == value) {
-		at_xdmac_write(atxdmac, AT_XDMAC_GSWF, atchan->mask);
+		at_xdmac_write(atxdmac, atxdmac->layout->gswf, atchan->mask);
  		while (!(at_xdmac_chan_read(atchan, AT_XDMAC_CIS) & AT_XDMAC_CIS_FIS))
  			cpu_relax();
  	}
@@ -1355,7 +1412,7 @@ at_xdmac_tx_status(struct dma_chan *chan, dma_cookie_t cookie,
  	 * FIFO flush ensures that data are really written.
  	 */
  	if ((desc->lld.mbr_cfg & mask) == value) {
-		at_xdmac_write(atxdmac, AT_XDMAC_GSWF, atchan->mask);
+		at_xdmac_write(atxdmac, atxdmac->layout->gswf, atchan->mask);
  		while (!(at_xdmac_chan_read(atchan, AT_XDMAC_CIS) & AT_XDMAC_CIS_FIS))
  			cpu_relax();
  	}
@@ -1620,7 +1677,7 @@ static int at_xdmac_device_pause(struct dma_chan *chan)
  		return 0;
 
  	spin_lock_irqsave(&atchan->lock, flags);
-	at_xdmac_write(atxdmac, AT_XDMAC_GRWS, atchan->mask);
+	at_xdmac_write(atxdmac, atxdmac->layout->grws, atchan->mask);
  	while (at_xdmac_chan_read(atchan, AT_XDMAC_CC)
  	       & (AT_XDMAC_CC_WRIP | AT_XDMAC_CC_RDIP))
  		cpu_relax();
@@ -1643,7 +1700,7 @@ static int at_xdmac_device_resume(struct dma_chan *chan)
  		return 0;
  	}
 
-	at_xdmac_write(atxdmac, AT_XDMAC_GRWR, atchan->mask);
+	at_xdmac_write(atxdmac, atxdmac->layout->grwr, atchan->mask);
  	clear_bit(AT_XDMAC_CHAN_IS_PAUSED, &atchan->status);
  	spin_unlock_irqrestore(&atchan->lock, flags);
 
@@ -1845,6 +1902,10 @@ static int at_xdmac_probe(struct platform_device *pdev)
  	atxdmac->regs = base;
  	atxdmac->irq = irq;
 
Quoted 6 lines

drivers/dma/at_xdmac.c static int at_xdmac_probe(struct platform_device *pdev) · line 1907

Quoted 3 lines
drivers/dma/at_xdmac.c +3 -0
+	atxdmac->layout = of_device_get_match_data(&pdev->dev);
+	if (!atxdmac->layout)
+		return -ENODEV;

I would get the data upper in the function, after getting irq. If data is not provided, you would spare some ops that will be done gratuitously.

Hi Tudor,

This would be difficult to do as atxdmac is allocated just a few lines before.
Also, actually the get_match_data should not fail normally. If this would fail it would mean that the driver is probed to a wrong driver compatible... which should not happen.

Thanks for reviewing. I am sending v2.

Eugen

Quoted 47 lines

With these addressed one may add:

Quoted 43 lines
drivers/dma/at_xdmac.c +5 -0
+
  	atxdmac->clk = devm_clk_get(&pdev->dev, "dma_clk");
  	if (IS_ERR(atxdmac->clk)) {
  		dev_err(&pdev->dev, "can't get dma_clk\n");
@@ -1988,6 +2049,10 @@ static const struct dev_pm_ops atmel_xdmac_dev_pm_ops = {
  static const struct of_device_id atmel_xdmac_dt_ids[] = {
  	{
  		.compatible = "atmel,sama5d4-dma",
+		.data = &at_xdmac_sama5d4_layout,
+	}, {
+		.compatible = "microchip,sama7g5-dma",
+		.data = &at_xdmac_sama7g5_layout,
  	}, {
  		/* sentinel */
  	}
drivers/dma/at_xdmac_regs.h +0 -9
index 3f7dda4c5743..7b4b4e24de70 100644
@@ -22,13 +22,6 @@
  #define AT_XDMAC_GE		0x1C	/* Global Channel Enable Register */
  #define AT_XDMAC_GD		0x20	/* Global Channel Disable Register */
  #define AT_XDMAC_GS		0x24	/* Global Channel Status Register */
-#define AT_XDMAC_GRS		0x28	/* Global Channel Read Suspend Register */
-#define AT_XDMAC_GWS		0x2C	/* Global Write Suspend Register */
-#define AT_XDMAC_GRWS		0x30	/* Global Channel Read Write Suspend Register */
-#define AT_XDMAC_GRWR		0x34	/* Global Channel Read Write Resume Register */
-#define AT_XDMAC_GSWR		0x38	/* Global Channel Software Request Register */
-#define AT_XDMAC_GSWS		0x3C	/* Global channel Software Request Status Register */
-#define AT_XDMAC_GSWF		0x40	/* Global Channel Software Flush Request Register */
  #define AT_XDMAC_VERSION	0xFFC	/* XDMAC Version Register */
 
  /* Channel relative registers offsets */
@@ -134,8 +127,6 @@
  #define AT_XDMAC_CSUS		0x30	/* Channel Source Microblock Stride */
  #define AT_XDMAC_CDUS		0x34	/* Channel Destination Microblock Stride */
 
-#define AT_XDMAC_CHAN_REG_BASE	0x50	/* Channel registers base address */
-
  /* Microblock control members */
  #define AT_XDMAC_MBR_UBC_UBLEN_MAX	0xFFFFFFUL	/* Maximum Microblock Length */
  #define AT_XDMAC_MBR_UBC_NDE		(0x1 << 24)	/* Next Descriptor Enable */
#13 lore raw

PATCH 6/7 dt-bindings: dmaengine: at_xdmac: add optional microchip,m2m property

In reply to Eugen Hristev

Add optional microchip,m2m property that specifies if a controller is dedicated to memory to memory operations only.

---
 Documentation/devicetree/bindings/dma/atmel-xdma.txt | 6 ++++++
 1 file changed, 6 insertions(+)
Documentation/devicetree/bindings/dma/atmel-xdma.txt +6 -0
index 510b7f25ba24..642da6b95a29 100644
@@ -15,6 +15,12 @@ the dmas property of client devices.
     interface identifier,
     - bit 30-24: PERID, peripheral identifier.
 
+Optional properties:
+- microchip,m2m: this controller is connected on AXI only to memory and it's
+	dedicated to memory to memory DMA operations. If this option is
+	missing, it's assumed that the DMA controller is connected to
+	peripherals, thus it's a per2mem and mem2per.
+
 Example:
 
 dma1: dma-controller@f0004000 {
Signature · 1 line
2.25.1
maintainer
#14 lore raw

Re: [PATCH 6/7] dt-bindings: dmaengine: at_xdmac: add optional microchip,m2m property

Quoted 13 lines · Eugen Hristev

Add optional microchip,m2m property that specifies if a controller is dedicated to memory to memory operations only.

---
 Documentation/devicetree/bindings/dma/atmel-xdma.txt | 6 ++++++
 1 file changed, 6 insertions(+)
Documentation/devicetree/bindings/dma/atmel-xdma.txt +0 -0
index 510b7f25ba24..642da6b95a29 100644

Documentation/devicetree/bindings/dma/atmel-xdma.txt the dmas property of client devices. · line 22

Quoted 8 lines
Documentation/devicetree/bindings/dma/atmel-xdma.txt +5 -0
@@ -15,6 +15,12 @@ the dmas property of client devices.
     interface identifier,
     - bit 30-24: PERID, peripheral identifier.
 
+Optional properties:
+- microchip,m2m: this controller is connected on AXI only to memory and it's
+	dedicated to memory to memory DMA operations. If this option is
+	missing, it's assumed that the DMA controller is connected to
+	peripherals, thus it's a per2mem and mem2per.

Wouldn't 'dma-requests = <0>' cover this case?

Rob

#15 lore raw

Re: [PATCH 6/7] dt-bindings: dmaengine: at_xdmac: add optional microchip,m2m property

Quoted 25 lines · Rob Herring
Quoted 13 lines · Eugen Hristev

Add optional microchip,m2m property that specifies if a controller is dedicated to memory to memory operations only.

---
  Documentation/devicetree/bindings/dma/atmel-xdma.txt | 6 ++++++
  1 file changed, 6 insertions(+)
Documentation/devicetree/bindings/dma/atmel-xdma.txt +0 -0
index 510b7f25ba24..642da6b95a29 100644

Documentation/devicetree/bindings/dma/atmel-xdma.txt the dmas property of client devices. · line 22

Quoted 8 lines
Documentation/devicetree/bindings/dma/atmel-xdma.txt +5 -0
@@ -15,6 +15,12 @@ the dmas property of client devices.
      interface identifier,
      - bit 30-24: PERID, peripheral identifier.
 
+Optional properties:
+- microchip,m2m: this controller is connected on AXI only to memory and it's
+     dedicated to memory to memory DMA operations. If this option is
+     missing, it's assumed that the DMA controller is connected to
+     peripherals, thus it's a per2mem and mem2per.

Wouldn't 'dma-requests = <0>' cover this case?

Quoted 2 lines

Rob

Hi Rob,

I do not think so. With requests = 0, it means that actually the DMA controller is unusable ?
Since you suggest requests = 0, it means that it cannot take requests at all ?
I do not find another example in current DT with this property set to zero.

Eugen

maintainer
#16 lore raw

Re: [PATCH 6/7] dt-bindings: dmaengine: at_xdmac: add optional microchip,m2m property

Hi Eugen,

Quoted 30 lines · On 16-10-20, 06:45, [email protected] wrote:
Quoted 25 lines · Rob Herring
Quoted 13 lines · Eugen Hristev

Add optional microchip,m2m property that specifies if a controller is dedicated to memory to memory operations only.

---
  Documentation/devicetree/bindings/dma/atmel-xdma.txt | 6 ++++++
  1 file changed, 6 insertions(+)
Documentation/devicetree/bindings/dma/atmel-xdma.txt +0 -0
index 510b7f25ba24..642da6b95a29 100644

Documentation/devicetree/bindings/dma/atmel-xdma.txt the dmas property of client devices. · line 22

Quoted 8 lines
Documentation/devicetree/bindings/dma/atmel-xdma.txt +5 -0
@@ -15,6 +15,12 @@ the dmas property of client devices.
      interface identifier,
      - bit 30-24: PERID, peripheral identifier.
 
+Optional properties:
+- microchip,m2m: this controller is connected on AXI only to memory and it's
+     dedicated to memory to memory DMA operations. If this option is
+     missing, it's assumed that the DMA controller is connected to
+     peripherals, thus it's a per2mem and mem2per.

Wouldn't 'dma-requests = <0>' cover this case?

Quoted 2 lines

Rob

Quoted 7 lines

Hi Rob,

I do not think so. With requests = 0, it means that actually the DMA controller is unusable ?
Since you suggest requests = 0, it means that it cannot take requests at all ?
I do not find another example in current DT with this property set to zero.

Not really, dma-requests implies "request signals supported" which are used for peripheral cases. m2m does not need request signals, so it is very reasonable to conclude that dma-requests = <0> would imply no peripheral support and only m2m support.

Thanks

Signature · 1 line
~Vinod
#17 lore raw

Re: [PATCH 6/7] dt-bindings: dmaengine: at_xdmac: add optional microchip,m2m property

Quoted 41 lines · Vinod Koul

Hi Eugen,

Quoted 30 lines · On 16-10-20, 06:45, [email protected] wrote:
Quoted 25 lines · Rob Herring
Quoted 13 lines · Eugen Hristev

Add optional microchip,m2m property that specifies if a controller is dedicated to memory to memory operations only.

---
   Documentation/devicetree/bindings/dma/atmel-xdma.txt | 6 ++++++
   1 file changed, 6 insertions(+)
Documentation/devicetree/bindings/dma/atmel-xdma.txt +0 -0
index 510b7f25ba24..642da6b95a29 100644

Documentation/devicetree/bindings/dma/atmel-xdma.txt the dmas property of client devices. · line 22

Quoted 8 lines
Documentation/devicetree/bindings/dma/atmel-xdma.txt +5 -0
@@ -15,6 +15,12 @@ the dmas property of client devices.
       interface identifier,
       - bit 30-24: PERID, peripheral identifier.
 
+Optional properties:
+- microchip,m2m: this controller is connected on AXI only to memory and it's
+     dedicated to memory to memory DMA operations. If this option is
+     missing, it's assumed that the DMA controller is connected to
+     peripherals, thus it's a per2mem and mem2per.

Wouldn't 'dma-requests = <0>' cover this case?

Quoted 2 lines

Rob

Quoted 7 lines

Hi Rob,

I do not think so. With requests = 0, it means that actually the DMA controller is unusable ?
Since you suggest requests = 0, it means that it cannot take requests at all ?
I do not find another example in current DT with this property set to zero.

Quoted 4 lines

Not really, dma-requests implies "request signals supported" which are used for peripheral cases. m2m does not need request signals, so it is very reasonable to conclude that dma-requests = <0> would imply no peripheral support and only m2m support.

Thanks for explaining, I will change accordingly then.

Eugen

Quoted 5 lines

Thanks
--
~Vinod

#18 lore raw

PATCH 7/7 dmaengine: at_xdmac: add AXI priority support and recommended settings

In reply to Eugen Hristev

The sama7g5 version of the XDMAC supports priority configuration and outstanding capabilities.
Add defines for the specific registers for this configuration, together with recommended settings.
However the settings are very different if the XDMAC is a mem2mem or a per2mem controller.
Thus, we need to differentiate according to device tree property.

---
 drivers/dma/at_xdmac.c      | 25 +++++++++++++++++++++++++
 drivers/dma/at_xdmac_regs.h | 16 ++++++++++++++++
 2 files changed, 41 insertions(+)
drivers/dma/at_xdmac.c +25 -0
index 874484a4e79f..8ea5558e127d 100644
@@ -57,6 +57,8 @@ struct at_xdmac_layout {
 	u8				chan_cc_reg_base;
 	/* Source/Destination Interface must be specified or not */
 	bool				sdif;
+	/* AXI queue priority configuration supported */
+	bool				axi_config;
 };
 
 /* ----- Channels ----- */
@@ -135,6 +137,7 @@ static struct at_xdmac_layout at_xdmac_sama5d4_layout = {
 	.gswf = 0x40,
 	.chan_cc_reg_base = 0x50,
 	.sdif = true,
+	.axi_config = false,
 };
 
 static struct at_xdmac_layout at_xdmac_sama7g5_layout = {
@@ -147,6 +150,7 @@ static struct at_xdmac_layout at_xdmac_sama7g5_layout = {
 	.gswf = 0x50,
 	.chan_cc_reg_base = 0x60,
 	.sdif = false,
+	.axi_config = true,
 };
 
 static inline void __iomem *at_xdmac_chan_reg_base(struct at_xdmac *atxdmac, unsigned int chan_nb)
@@ -1863,6 +1867,25 @@ static int atmel_xdmac_resume(struct device *dev)
 }
 #endif /* CONFIG_PM_SLEEP */
 
+static void at_xdmac_axi_config(struct platform_device *pdev)
+{
+	struct at_xdmac	*atxdmac = (struct at_xdmac *)platform_get_drvdata(pdev);
+	bool dev_m2m;
+
+	if (!atxdmac->layout->axi_config)
+		return; /* Not supported */
+
+	dev_m2m = of_property_read_bool(pdev->dev.of_node, "microchip,m2m");
+
+	if (dev_m2m) {
+		at_xdmac_write(atxdmac, AT_XDMAC_GCFG, AT_XDMAC_GCFG_M2M);
+		at_xdmac_write(atxdmac, AT_XDMAC_GWAC, AT_XDMAC_GWAC_M2M);
+	} else {
+		at_xdmac_write(atxdmac, AT_XDMAC_GCFG, AT_XDMAC_GCFG_P2M);
+		at_xdmac_write(atxdmac, AT_XDMAC_GWAC, AT_XDMAC_GWAC_P2M);
+	}
+}
+
 static int at_xdmac_probe(struct platform_device *pdev)
 {
 	struct at_xdmac	*atxdmac;
@@ -2008,6 +2031,8 @@ static int at_xdmac_probe(struct platform_device *pdev)
 	dev_info(&pdev->dev, "%d channels, mapped at 0x%p\n",
 		 nr_channels, atxdmac->regs);
 
+	at_xdmac_axi_config(pdev);
+
 	return 0;
 
 err_dma_unregister:
drivers/dma/at_xdmac_regs.h +16 -0
index 7b4b4e24de70..e5a58f6194aa 100644
@@ -14,7 +14,23 @@
 #define		AT_XDMAC_FIFO_SZ(i)	(((i) >> 5) & 0x7FF)		/* Number of Bytes */
 #define		AT_XDMAC_NB_REQ(i)	((((i) >> 16) & 0x3F) + 1)	/* Number of Peripheral Requests Minus One */
 #define AT_XDMAC_GCFG		0x04	/* Global Configuration Register */
+#define		AT_XDMAC_WRHP(i)	(((i) & 0xF) << 4)
+#define		AT_XDMAC_WRMP(i)	(((i) & 0xF) << 8)
+#define		AT_XDMAC_WRLP(i)	(((i) & 0xF) << 12)
+#define		AT_XDMAC_RDHP(i)	(((i) & 0xF) << 16)
+#define		AT_XDMAC_RDMP(i)	(((i) & 0xF) << 20)
+#define		AT_XDMAC_RDLP(i)	(((i) & 0xF) << 24)
+#define		AT_XDMAC_RDSG(i)	(((i) & 0xF) << 28)
+#define AT_XDMAC_GCFG_M2M	(AT_XDMAC_RDLP(0xF) | AT_XDMAC_WRLP(0xF))
+#define AT_XDMAC_GCFG_P2M	(AT_XDMAC_RDSG(0x1) | AT_XDMAC_RDHP(0x3) | \
+				AT_XDMAC_WRHP(0x5))
 #define AT_XDMAC_GWAC		0x08	/* Global Weighted Arbiter Configuration Register */
+#define		AT_XDMAC_PW0(i)		(((i) & 0xF) << 0)
+#define		AT_XDMAC_PW1(i)		(((i) & 0xF) << 4)
+#define		AT_XDMAC_PW2(i)		(((i) & 0xF) << 8)
+#define		AT_XDMAC_PW3(i)		(((i) & 0xF) << 12)
+#define AT_XDMAC_GWAC_M2M	0
+#define AT_XDMAC_GWAC_P2M	(AT_XDMAC_PW0(0xF) | AT_XDMAC_PW2(0xF))
 #define AT_XDMAC_GIE		0x0C	/* Global Interrupt Enable Register */
 #define AT_XDMAC_GID		0x10	/* Global Interrupt Disable Register */
 #define AT_XDMAC_GIM		0x14	/* Global Interrupt Mask Register */
Signature · 7 lines
2.25.1


_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel