arm64: dts: ti: k3-j7200: Add properties and sync with uboot
Subsystems (2)
v2 cover arm64: dts: ti: k3-j7200: Add properties and sync with uboot
In continuation of patch series posted by Nishanth
for sync of uboot device tree with kernel device tree for AM64 SOC.
https://lore.kernel.org/linux-arm-kernel/[email protected]/
This series extend device tree sync/clean up for J7200 SOC.
This patch series build on top of
https://lore.kernel.org/all/[email protected]
Changes since v1:
https://lore.kernel.org/all/[email protected]/
* Add general purpose timers:
Addded CLKSEL_VD clock for odd numbered timers
Marked MCU_Timer as reserved, fixed clock index for main_timer13
*Configure pinctrl for timer IO pads
Marked mcu_timerio_input as reserved
*main_pmx0 clean up
Splitted into two patches, One for UART and second for i2c duplication removal
*Add uart pin mux in wkup_pmx0
No change
*Add bootph-pre-ram for u-boot
patch dropped, later will add bootph-pre-ram property later for all nodes.
Udit Kumar (5):
arm64: dts: ti: k3-j7200: Add general purpose timers
arm64: dts: ti: k3-j7200: Configure pinctrl for timer IO pads
arm64: dts: ti: k3-j7200-common-proc-board: main_pmx0 clean up
arm64: dts: ti: k3-j7200-common-proc-board: remove duplicate main_i2c0
pin mux
arm64: dts: ti: k3-j7200-common-proc-board: Add uart pin mux in
wkup_pmx0
.../dts/ti/k3-j7200-common-proc-board.dts | 32 ++- arch/arm64/boot/dts/ti/k3-j7200-main.dtsi | 258 ++++++++++++++++++ .../boot/dts/ti/k3-j7200-mcu-wakeup.dtsi | 150 ++++++++++ 3 files changed, 436 insertions(+), 4 deletions(-)
Signature · 1 line
2.34.1
PATCH v2 1/5 arm64: dts: ti: k3-j7200: Add general purpose timers
There are 20 general purpose timers on j721e that can be used for things like PWM using pwm-omap-dmtimer driver. There are also additional ten timers in the MCU domain which are meant for MCU firmware usage and hence marked reserved by default.
The odd numbered timers have the option of being cascaded to even timers to create a 64 bit non-atomic counter which is racy in simple usage, hence the clock muxes are explicitly setup to individual 32 bit counters driven off system crystal (HFOSC) as default.
--- arch/arm64/boot/dts/ti/k3-j7200-main.dtsi | 240 ++++++++++++++++++ .../boot/dts/ti/k3-j7200-mcu-wakeup.dtsi | 130 ++++++++++ 2 files changed, 370 insertions(+)
arch/arm64/boot/dts/ti/k3-j7200-main.dtsi +240 -0
@@ -971,6 +971,246 @@ watchdog1: watchdog@2210000 { assigned-clock-parents = <&k3_clks 253 5>; }; + main_timer0: timer@2400000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x2400000 0x00 0x400>; + interrupts = <GIC_SPI 224 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 49 1>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 49 1>; + assigned-clock-parents = <&k3_clks 49 2>; + power-domains = <&k3_pds 49 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + + main_timer1: timer@2410000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x2410000 0x00 0x400>; + interrupts = <GIC_SPI 225 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 50 1>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 50 1>, <&k3_clks 313 0>; + assigned-clock-parents = <&k3_clks 50 2>, <&k3_clks 313 1>; + power-domains = <&k3_pds 50 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + + main_timer2: timer@2420000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x2420000 0x00 0x400>; + interrupts = <GIC_SPI 226 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 51 1>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 51 1>; + assigned-clock-parents = <&k3_clks 51 2>; + power-domains = <&k3_pds 49 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + + main_timer3: timer@2430000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x2430000 0x00 0x400>; + interrupts = <GIC_SPI 227 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 52 1>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 52 1>, <&k3_clks 314 0>; + assigned-clock-parents = <&k3_clks 52 2>, <&k3_clks 314 1>; + power-domains = <&k3_pds 52 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + + main_timer4: timer@2440000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x2440000 0x00 0x400>; + interrupts = <GIC_SPI 228 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 53 1>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 53 1>; + assigned-clock-parents = <&k3_clks 53 2>; + power-domains = <&k3_pds 53 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + + main_timer5: timer@2450000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x2450000 0x00 0x400>; + interrupts = <GIC_SPI 229 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 54 1>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 54 1>, <&k3_clks 315 0>; + assigned-clock-parents = <&k3_clks 54 2>, <&k3_clks 315 1>; + power-domains = <&k3_pds 54 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + + main_timer6: timer@2460000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x2460000 0x00 0x400>; + interrupts = <GIC_SPI 230 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 55 1>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 55 1>; + assigned-clock-parents = <&k3_clks 55 2>; + power-domains = <&k3_pds 55 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + + main_timer7: timer@2470000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x2470000 0x00 0x400>; + interrupts = <GIC_SPI 231 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 57 1>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 57 1>, <&k3_clks 316 0>; + assigned-clock-parents = <&k3_clks 57 2>, <&k3_clks 316 1>; + power-domains = <&k3_pds 57 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + + main_timer8: timer@2480000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x2480000 0x00 0x400>; + interrupts = <GIC_SPI 232 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 58 1>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 58 1>; + assigned-clock-parents = <&k3_clks 58 2>; + power-domains = <&k3_pds 58 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + + main_timer9: timer@2490000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x2490000 0x00 0x400>; + interrupts = <GIC_SPI 233 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 59 1>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 59 1>, <&k3_clks 317 0>; + assigned-clock-parents = <&k3_clks 59 2>, <&k3_clks 317 1>; + power-domains = <&k3_pds 59 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + + main_timer10: timer@24a0000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x24a0000 0x00 0x400>; + interrupts = <GIC_SPI 234 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 60 1>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 60 1>; + assigned-clock-parents = <&k3_clks 60 2>; + power-domains = <&k3_pds 60 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + + main_timer11: timer@24b0000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x24b0000 0x00 0x400>; + interrupts = <GIC_SPI 235 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 62 1>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 62 1>, <&k3_clks 318 0>; + assigned-clock-parents = <&k3_clks 62 2>, <&k3_clks 318 1>; + power-domains = <&k3_pds 62 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + + main_timer12: timer@24c0000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x24c0000 0x00 0x400>; + interrupts = <GIC_SPI 236 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 63 1>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 63 1>; + assigned-clock-parents = <&k3_clks 63 2>; + power-domains = <&k3_pds 63 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + + main_timer13: timer@24d0000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x24d0000 0x00 0x400>; + interrupts = <GIC_SPI 237 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 64 1>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 64 1>, <&k3_clks 319 0>; + assigned-clock-parents = <&k3_clks 64 2>, <&k3_clks 319 1>; + power-domains = <&k3_pds 64 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + + main_timer14: timer@24e0000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x24e0000 0x00 0x400>; + interrupts = <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 65 1>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 65 1>; + assigned-clock-parents = <&k3_clks 65 2>; + power-domains = <&k3_pds 65 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + + main_timer15: timer@24f0000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x24f0000 0x00 0x400>; + interrupts = <GIC_SPI 239 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 66 1>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 66 1>, <&k3_clks 320 0>; + assigned-clock-parents = <&k3_clks 66 2>, <&k3_clks 320 1>; + power-domains = <&k3_pds 66 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + + main_timer16: timer@2500000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x2500000 0x00 0x400>; + interrupts = <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 67 1>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 67 1>; + assigned-clock-parents = <&k3_clks 67 2>; + power-domains = <&k3_pds 67 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + + main_timer17: timer@2510000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x2510000 0x00 0x400>; + interrupts = <GIC_SPI 241 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 68 1>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 68 1>, <&k3_clks 321 0>; + assigned-clock-parents = <&k3_clks 68 2>, <&k3_clks 321 1>; + power-domains = <&k3_pds 68 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + + main_timer18: timer@2520000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x2520000 0x00 0x400>; + interrupts = <GIC_SPI 242 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 69 1>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 69 1>; + assigned-clock-parents = <&k3_clks 69 2>; + power-domains = <&k3_pds 69 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + + main_timer19: timer@2530000 { + compatible = "ti,am654-timer"; + reg = <0x00 0x2530000 0x00 0x400>; + interrupts = <GIC_SPI 243 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&k3_clks 70 1>; + clock-names = "fck"; + assigned-clocks = <&k3_clks 70 1>, <&k3_clks 322 0>; + assigned-clock-parents = <&k3_clks 70 2>, <&k3_clks 322 1>; + power-domains = <&k3_pds 70 TI_SCI_PD_EXCLUSIVE>; + ti,timer-pwm; + }; + main_r5fss0: r5fss@5c00000 { compatible = "ti,j7200-r5fss"; ti,cluster-mode = <1>;
arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi +130 -0
136 lines not on this page · raw message
Signature · 1 line
2.34.1
PATCH v2 2/5 arm64: dts: ti: k3-j7200: Configure pinctrl for timer IO pads
In reply to Udit KumarThere are timer IO pads in the MCU domain, and in the MAIN domain. These pads can be muxed for the related timers.
There are timer IO control registers for input and output. The registers for CTRLMMR_TIMER*_CTRL and CTRLMMR_MCU_TIMER*_CTRL are used to control the input. The registers for CTCTRLMMR_TIMERIO*_CTRL and CTRLMMR_MCU_TIMERIO*_CTRL the output.
The multiplexing is documented in TRM "5.1.2.3.1.4 Timer IO Muxing Control Registers" and "5.1.3.3.1.5 Timer IO Muxing Control Registers", and the CASCADE_EN bit is documented in TRM "12.6.3.1 Timers Overview".
For chaining timers, the timer IO control registers also have a CASCADE_EN input bit in the CTRLMMR_TIMER*_CTRL in the registers. The CASCADE_EN bit muxes the previous timer output, or possibly and external TIMER_IO pad source, to the input clock of the selected timer instance for odd numered timers. For the even numbered timers, the CASCADE_EN bit does not do anything. The timer cascade input routing options are shown in TRM "Figure 12-3224. Timers Overview". For handling beyond multiplexing, the driver support for timer cascading should be likely be handled via the clock framework.
The MCU timer controls are also marked as reserved for usage by the MCU firmware.
--- arch/arm64/boot/dts/ti/k3-j7200-main.dtsi | 18 +++++++++++++++++ .../boot/dts/ti/k3-j7200-mcu-wakeup.dtsi | 20 +++++++++++++++++++ 2 files changed, 38 insertions(+)
arch/arm64/boot/dts/ti/k3-j7200-main.dtsi +18 -0
@@ -392,6 +392,24 @@ cpts@3d000 { }; }; + /* TIMERIO pad input CTRLMMR_TIMER*_CTRL registers */ + main_timerio_input: pinctrl@104200 { + compatible = "pinctrl-single"; + reg = <0x0 0x104200 0x0 0x50>; + #pinctrl-cells = <1>; + pinctrl-single,register-width = <32>; + pinctrl-single,function-mask = <0x000001ff>; + }; + + /* TIMERIO pad output CTCTRLMMR_TIMERIO*_CTRL registers */ + main_timerio_output: pinctrl@104280 { + compatible = "pinctrl-single"; + reg = <0x0 0x104280 0x0 0x20>; + #pinctrl-cells = <1>; + pinctrl-single,register-width = <32>; + pinctrl-single,function-mask = <0x0000001f>; + }; + main_pmx0: pinctrl@11c000 { compatible = "pinctrl-single"; /* Proxy 0 addressing */
arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi +20 -0
@@ -183,6 +183,26 @@ chipid@43000014 { reg = <0x00 0x43000014 0x00 0x4>; }; + /* MCU_TIMERIO pad input CTRLMMR_MCU_TIMER*_CTRL registers */ + mcu_timerio_input: pinctrl@40f04200 { + compatible = "pinctrl-single"; + reg = <0x0 0x40f04200 0x0 0x28>; + #pinctrl-cells = <1>; + pinctrl-single,register-width = <32>; + pinctrl-single,function-mask = <0x0000000F>; + status = "reserved"; + }; + + /* MCU_TIMERIO pad output CTRLMMR_MCU_TIMERIO*_CTRL registers */ + mcu_timerio_output: pinctrl@40f04280 { + compatible = "pinctrl-single"; + reg = <0x0 0x40f04280 0x0 0x28>; + #pinctrl-cells = <1>; + pinctrl-single,register-width = <32>; + pinctrl-single,function-mask = <0x0000000F>; + status = "reserved"; + }; + wkup_pmx0: pinctrl@4301c000 { compatible = "pinctrl-single"; /* Proxy 0 addressing */
Signature · 1 line
2.34.1
Re: [PATCH v2 2/5] arm64: dts: ti: k3-j7200: Configure pinctrl for timer IO pads
Quoted 22 lines · Udit Kumar
There are timer IO pads in the MCU domain, and in the MAIN domain. These pads can be muxed for the related timers.
There are timer IO control registers for input and output. The registers for CTRLMMR_TIMER*_CTRL and CTRLMMR_MCU_TIMER*_CTRL are used to control the input. The registers for CTCTRLMMR_TIMERIO*_CTRL and CTRLMMR_MCU_TIMERIO*_CTRL the output.
The multiplexing is documented in TRM "5.1.2.3.1.4 Timer IO Muxing Control Registers" and "5.1.3.3.1.5 Timer IO Muxing Control Registers", and the
CASCADE_ENbit is documented in TRM "12.6.3.1 Timers Overview".For chaining timers, the timer IO control registers also have a
CASCADE_ENinput bit in the CTRLMMR_TIMER*_CTRL in the registers. TheCASCADE_ENbit muxes the previous timer output, or possibly and externalTIMER_IOpad source, to the input clock of the selected timer instance for odd numered timers. For the even numbered timers, theCASCADE_ENbit does not do anything. The timer cascade input routing options are shown in TRM "Figure 12-3224. Timers Overview". For handling beyond multiplexing, the driver support for timer cascading should be likely be handled via the clock framework.
Quoted 2 lines
The MCU timer controls are also marked as reserved for usage by the MCU firmware.
_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
PATCH v2 3/5 arm64: dts: ti: k3-j7200-common-proc-board: main_pmx0 clean up
In reply to Udit KumarAdd main_uart0 pin mux in board common file
--- arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts | 11 +++++++++++ 1 file changed, 11 insertions(+)
arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts +11 -0
@@ -113,6 +113,15 @@ J721E_IOPAD(0xd8, PIN_INPUT_PULLUP, 0) /* (W2) I2C0_SDA */ >; }; + main_uart0_pins_default: main_uart0_pins_default { + pinctrl-single,pins = < + J721E_IOPAD(0xb0, PIN_INPUT, 0) /* (T16) UART0_RXD */ + J721E_IOPAD(0xb4, PIN_OUTPUT, 0) /* (T17) UART0_TXD */ + J721E_IOPAD(0xc0, PIN_INPUT, 2) /* (W3) SPI0_CS0.UART0_CTSn */ + J721E_IOPAD(0xc4, PIN_OUTPUT, 2) /* (U5) SPI0_CS1.UART0_RTSn */ + >; + }; + main_i2c1_pins_default: main-i2c1-pins-default { pinctrl-single,pins = < J721E_IOPAD(0xdc, PIN_INPUT_PULLUP, 3) /* (U3) ECAP0_IN_APWM_OUT.I2C1_SCL */
@@ -162,6 +171,8 @@ &main_uart0 { status = "okay"; /* Shared with ATF on this platform */ power-domains = <&k3_pds 146 TI_SCI_PD_SHARED>; + pinctrl-names = "default"; + pinctrl-0 = <&main_uart0_pins_default>; }; &main_uart1 {
Signature · 1 line
2.34.1
Nishanth Menon
maintainerRe: [PATCH v2 3/5] arm64: dts: ti: k3-j7200-common-proc-board: main_pmx0 clean up
Quoted 1 line · Udit Kumar
Add
main_uart0pin mux in board common file
$subject is a bit misleading.. I think the intent is to mux the console explicitly rather than a pinmux cleanup itself.
Quoted 38 lines
Signed-off-by Udit Kumar <[email protected]>--- arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts | 11 +++++++++++ 1 file changed, 11 insertions(+)arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts +11
-0@@ -113,6 +113,15 @@ J721E_IOPAD(0xd8, PIN_INPUT_PULLUP, 0) /* (W2) I2C0_SDA */ >; }; + main_uart0_pins_default: main_uart0_pins_default { + pinctrl-single,pins = < + J721E_IOPAD(0xb0, PIN_INPUT, 0) /* (T16) UART0_RXD */ + J721E_IOPAD(0xb4, PIN_OUTPUT, 0) /* (T17) UART0_TXD */ + J721E_IOPAD(0xc0, PIN_INPUT, 2) /* (W3) SPI0_CS0.UART0_CTSn */ + J721E_IOPAD(0xc4, PIN_OUTPUT, 2) /* (U5) SPI0_CS1.UART0_RTSn */ + >; + }; + main_i2c1_pins_default: main-i2c1-pins-default { pinctrl-single,pins = < J721E_IOPAD(0xdc, PIN_INPUT_PULLUP, 3) /* (U3) ECAP0_IN_APWM_OUT.I2C1_SCL */@@ -162,6 +171,8 @@ &main_uart0 { status = "okay"; /* Shared with ATF on this platform */ power-domains = <&k3_pds 146 TI_SCI_PD_SHARED>; + pinctrl-names = "default"; + pinctrl-0 = <&main_uart0_pins_default>; }; &main_uart1 {Signature · 1 line
2.34.1
Signature · 8 lines
Regards, Nishanth Menon Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3 1A34 DDB5 849D 1736 249D _______________________________________________ linux-arm-kernel mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Re: [PATCH v2 3/5] arm64: dts: ti: k3-j7200-common-proc-board: main_pmx0 clean up
Thanks
Quoted 4 lines · Nishanth Menon
Quoted 1 line · Udit Kumar
Add
main_uart0pin mux in board common file$subject is a bit misleading.. I think the intent is to mux the console explicitly rather than a pinmux cleanup itself.
oops, missed to changed subject of this patch after split.
Will address in v3.
Quoted 37 lines
Quoted 37 lines
Signed-off-by Udit Kumar<[email protected]>--- arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts | 11 +++++++++++ 1 file changed, 11 insertions(+)arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts +11
-0@@ -113,6 +113,15 @@ J721E_IOPAD(0xd8, PIN_INPUT_PULLUP, 0) /* (W2) I2C0_SDA */ >; }; + main_uart0_pins_default: main_uart0_pins_default { + pinctrl-single,pins = < + J721E_IOPAD(0xb0, PIN_INPUT, 0) /* (T16) UART0_RXD */ + J721E_IOPAD(0xb4, PIN_OUTPUT, 0) /* (T17) UART0_TXD */ + J721E_IOPAD(0xc0, PIN_INPUT, 2) /* (W3) SPI0_CS0.UART0_CTSn */ + J721E_IOPAD(0xc4, PIN_OUTPUT, 2) /* (U5) SPI0_CS1.UART0_RTSn */ + >; + }; + main_i2c1_pins_default: main-i2c1-pins-default { pinctrl-single,pins = < J721E_IOPAD(0xdc, PIN_INPUT_PULLUP, 3) /* (U3) ECAP0_IN_APWM_OUT.I2C1_SCL */@@ -162,6 +171,8 @@ &main_uart0 { status = "okay"; /* Shared with ATF on this platform */ power-domains = <&k3_pds 146 TI_SCI_PD_SHARED>; + pinctrl-names = "default"; + pinctrl-0 = <&main_uart0_pins_default>; }; &main_uart1 {Signature · 1 line
2.34.1
PATCH v2 4/5 arm64: dts: ti: k3-j7200-common-proc-board: remove duplicate main_i2c0 pin mux
In reply to Udit Kumarmain_i2c0 pin mux was duplicated in som and common file. So removing duplicated node from common file
--- arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts | 7 ------- 1 file changed, 7 deletions(-)
arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts +0 -7
@@ -106,13 +106,6 @@ J721E_WKUP_IOPAD(0x0030, PIN_INPUT, 0) /* (L4) MCU_MDIO0_MDIO */ }; &main_pmx0 { - main_i2c0_pins_default: main-i2c0-pins-default { - pinctrl-single,pins = < - J721E_IOPAD(0xd4, PIN_INPUT_PULLUP, 0) /* (V3) I2C0_SCL */ - J721E_IOPAD(0xd8, PIN_INPUT_PULLUP, 0) /* (W2) I2C0_SDA */ - >; - }; - main_uart0_pins_default: main_uart0_pins_default { pinctrl-single,pins = < J721E_IOPAD(0xb0, PIN_INPUT, 0) /* (T16) UART0_RXD */
Signature · 1 line
2.34.1
PATCH v2 5/5 arm64: dts: ti: k3-j7200-common-proc-board: Add uart pin mux in wkup_pmx0
In reply to Udit KumarAdd uart pin mux of wkup domain into common board file.
--- .../dts/ti/k3-j7200-common-proc-board.dts | 22 ++++++++++++++++++- 1 file changed, 21 insertions(+), 1 deletion(-)
arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts +21 -1
@@ -79,6 +79,24 @@ vdd_sd_dv: gpio-regulator-TLV71033 { }; }; +&wkup_pmx0 { + mcu_uart0_pins_default: mcu_uart0_pins_default { + pinctrl-single,pins = < + J721E_WKUP_IOPAD(0xf4, PIN_INPUT, 0) /* (D20) MCU_UART0_RXD */ + J721E_WKUP_IOPAD(0xf0, PIN_OUTPUT, 0) /* (D19) MCU_UART0_TXD */ + J721E_WKUP_IOPAD(0xf8, PIN_INPUT, 0) /* (E20) MCU_UART0_CTSn */ + J721E_WKUP_IOPAD(0xfc, PIN_OUTPUT, 0) /* (E21) MCU_UART0_RTSn */ + >; + }; + + wkup_uart0_pins_default: wkup_uart0_pins_default { + pinctrl-single,pins = < + J721E_WKUP_IOPAD(0xb0, PIN_INPUT, 0) /* (B14) WKUP_UART0_RXD */ + J721E_WKUP_IOPAD(0xb4, PIN_OUTPUT, 0) /* (A14) WKUP_UART0_TXD */ + >; + }; +}; + &wkup_pmx2 { mcu_cpsw_pins_default: mcu-cpsw-pins-default { pinctrl-single,pins = <
@@ -157,7 +175,9 @@ &wkup_uart0 { &mcu_uart0 { status = "okay"; - /* Default pinmux */ + pinctrl-names = "default"; + pinctrl-0 = <&mcu_uart0_pins_default>; + clock-frequency = <96000000>; }; &main_uart0 {
Signature · 1 line
2.34.1