2.6.26-rc9-git9 doesn't boot on Macintel
Is anyone able to boot the 2.6.26rc9git9 or 2.6.26rc9git12
kernels on a Macintel machine? On my MacBook Pro (second gen with rEFIt installed for dual booting), I find that MMCONFIG doesn't seem to be in use under the 2.6.26 kernels. I get the following hang when booting rc9git9 or rc9git12...
ACPI: bus type pci registered
PCI: MCFG configuration 0: base f0000000 segment 0 buses 0 - 255
PCI: Not using MMCONFIG
PCI: Using configuration type 1 for base access
ACPI: EC: EC description table is found, configuring boot EC
ACPI: EC: non-query interrupt received switching to interrupt mode
ACPI: BIOS_OSI (Linux) query ignored via DMI
ACPI: Interpreter enabled
ACPI: (supports S0 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
PCI: MCFG configuration 0: base f0000000 segment 0 buses 0 - 255
PCI: BIOS Bug: MCFG area at f0000000 is not reserved in ACPI motherboard resources
PCI: Not using MMCONFIG
ACPI: EC:GPE=0x17, I/O: command/status=0x66, data=0x62
ACPI: EC: driver started in interrupt mode
ACPI: PCI Root Bridge [PCI0] (0000:00)
pci 0000:00:1f.0: quirk: region 0400-047f claimed by ICH6 ACPI/GPIO/TCO pci 0000:00:1f.0: quirk: region 0500-053f claimed by ICH6 GPIO
This compares to the same section in a normal boot of 2.6.25.10...
ACPI: bus type pci registered
PCI: Using MMCONFIG at f0000000 - ffffffff
PCI: Using configuration type 1
ACPI: EC: EC description table is found, configuring boot EC
ACPI: EC: non-query interrupt received, switching to interrupt mode
ACPI: BIOS _OSI(Linux) query ignored via DMI
ACPI: Interpreter enabled
ACPI: (supports S0 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: EC: GPE = 0x17, I/O: command/status = 0x66, data = 0x62
ACPI: EC: driver started in poll mode
ACPI: PCI Root Bridge [PCI0] (0000:00)
pci 0000:00:1f.0: quirk: region 0400-047f claimed by ICH6 ACPI/GPIO/TCO pci 0000:00:1f.0: quirk: region 0500-053f claimed by ICH6 GPIO
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEGP._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP02._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP03._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 7 10 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 7 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 7 *10 12 14 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 *11 12 14 15) Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
ACPI: EC: non-query interrupt received, switching to interrupt mode
pnp: PnP ACPI: found 9 devices
ACPI: ACPI bus type pnp unregistered
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
NetLabel: Initializing
..etc. My understanding is that the EFI in use on Macintel requires the use of MMCONFIG so the boot failure isn't surprising but the absence of MMCONFIG is.
Jack
Quoted 69 lines · Jack Howarth
Is anyone able to boot the 2.6.26rc9git9 or 2.6.26rc9git12
kernels on a Macintel machine? On my MacBook Pro (second gen with rEFIt installed for dual booting), I find that MMCONFIG doesn't seem to be in use under the 2.6.26 kernels. I get the following hang when booting rc9git9 or rc9git12...ACPI: bus type pci registered
PCI: MCFG configuration 0: basef0000000segment 0 buses 0 - 255
PCI: Not using MMCONFIG
PCI: Using configuration type 1 for base access
ACPI: EC: EC description table is found, configuring boot EC
ACPI: EC: non-query interrupt received switching to interrupt mode
ACPI:BIOS_OSI(Linux) query ignored via DMI
ACPI: Interpreter enabled
ACPI: (supports S0 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
PCI: MCFG configuration 0: basef0000000segment 0 buses 0 - 255
PCI: BIOS Bug: MCFG area atf0000000is not reserved in ACPI motherboard resources
PCI: Not using MMCONFIG
ACPI: EC:GPE=0x17, I/O: command/status=0x66, data=0x62
ACPI: EC: driver started in interrupt mode
ACPI: PCI Root Bridge [PCI0] (0000:00)
pci 0000:00:1f.0: quirk: region 0400-047f claimed by ICH6 ACPI/GPIO/TCO pci 0000:00:1f.0: quirk: region 0500-053f claimed by ICH6 GPIOThis compares to the same section in a normal boot of 2.6.25.10...
ACPI: bus type pci registered
PCI: Using MMCONFIG atf0000000- ffffffff
PCI: Using configuration type 1
ACPI: EC: EC description table is found, configuring boot EC
ACPI: EC: non-query interrupt received, switching to interrupt mode
ACPI: BIOS_OSI(Linux)query ignored via DMI
ACPI: Interpreter enabled
ACPI: (supports S0 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: EC: GPE =0x17, I/O: command/status =0x66, data =0x62
ACPI: EC: driver started in poll mode
ACPI: PCI Root Bridge [PCI0] (0000:00)
pci 0000:00:1f.0: quirk: region 0400-047f claimed by ICH6 ACPI/GPIO/TCO pci 0000:00:1f.0: quirk: region 0500-053f claimed by ICH6 GPIO
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEGP._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP02._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP03._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 7 10 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 7 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 7 *10 12 14 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 *11 12 14 15) Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
ACPI: EC: non-query interrupt received, switching to interrupt mode
pnp: PnP ACPI: found 9 devices
ACPI: ACPI bus type pnp unregistered
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
NetLabel: Initializing
Quoted 10 lines
..etc. My understanding is that the EFI in use on Macintel requires the use of MMCONFIG so the boot failure isn't surprising but the absence of MMCONFIG is.
Jack
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
yeah I'm able to boot up with the latest git on macbook pro. if want to use my .config its attached(just use caution she isn't pretty, uneded stuff in there)
regards;
Signature · 1 line
Justin P. Mattock
Quoted 43 lines · Jack Howarth
Is anyone able to boot the 2.6.26rc9git9 or 2.6.26rc9git12
kernels on a Macintel machine? On my MacBook Pro (second gen with rEFIt installed for dual booting), I find that MMCONFIG doesn't seem to be in use under the 2.6.26 kernels. I get the following hang when booting rc9git9 or rc9git12...ACPI: bus type pci registered
PCI: MCFG configuration 0: basef0000000segment 0 buses 0 - 255
PCI: Not using MMCONFIG
PCI: Using configuration type 1 for base access
ACPI: EC: EC description table is found, configuring boot EC
ACPI: EC: non-query interrupt received switching to interrupt mode
ACPI:BIOS_OSI(Linux) query ignored via DMI
ACPI: Interpreter enabled
ACPI: (supports S0 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
PCI: MCFG configuration 0: basef0000000segment 0 buses 0 - 255
PCI: BIOS Bug: MCFG area atf0000000is not reserved in ACPI motherboard resources
PCI: Not using MMCONFIG
ACPI: EC:GPE=0x17, I/O: command/status=0x66, data=0x62
ACPI: EC: driver started in interrupt mode
ACPI: PCI Root Bridge [PCI0] (0000:00)
pci 0000:00:1f.0: quirk: region 0400-047f claimed by ICH6 ACPI/GPIO/TCO pci 0000:00:1f.0: quirk: region 0500-053f claimed by ICH6 GPIOThis compares to the same section in a normal boot of 2.6.25.10...
ACPI: bus type pci registered
PCI: Using MMCONFIG atf0000000- ffffffff
PCI: Using configuration type 1
ACPI: EC: EC description table is found, configuring boot EC
ACPI: EC: non-query interrupt received, switching to interrupt mode
ACPI: BIOS_OSI(Linux)query ignored via DMI
ACPI: Interpreter enabled
ACPI: (supports S0 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: EC: GPE =0x17, I/O: command/status =0x66, data =0x62
ACPI: EC: driver started in poll mode
ACPI: PCI Root Bridge [PCI0] (0000:00)
pci 0000:00:1f.0: quirk: region 0400-047f claimed by ICH6 ACPI/GPIO/TCO pci 0000:00:1f.0: quirk: region 0500-053f claimed by ICH6 GPIO
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[...]
Quoted 3 lines
..etc. My understanding is that the EFI in use on Macintel requires the use of MMCONFIG so the boot failure isn't surprising but the absence of MMCONFIG is.
I have no idea... Here is a Mac mini which just booted 2.6.26 x86-64:
ACPI: bus type pci registered
PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
PCI: MCFG area at e0000000 reserved in E820
PCI: Using MMCONFIG at e0000000 - efffffff
PCI: Using configuration type 1 for base access
ACPI: EC: EC description table is found, configuring boot EC
ACPI: BIOS _OSI(Linux) query ignored via DMI
ACPI: Interpreter enabled
ACPI: (supports S0 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: EC: GPE = 0x17, I/O: command/status = 0x66, data = 0x62
ACPI: EC: driver started in poll mode
ACPI: PCI Root Bridge [PCI0] (0000:00)
pci 0000:00:1f.0: quirk: region 0400-047f claimed by ICH6 ACPI/GPIO/TCO pci 0000:00:1f.0: quirk: region 0500-053f claimed by ICH6 GPIO
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[...]
There is a CONFIG_PCI_MMCONFIG=y in its .config, FWIW. I too have rEFIt installed on this mini. dmidecode says it is a Macmini1,1.
Signature · 3 lines
Stefan Richter -=====-==--- -=== -===- http://arcgraph.de/sr/