eth0 and loopback problems.
Hi all!
I think it's a bug....
HOSTA# ifconfig eth0 192.168.0.1
HOSTA# ifconfig eth0 down
HOSTA# ping 192.168.0.1
(the ping works, like all other ICMP / TCP /UDP ... application. In other words: all work like eth0 in UP mode when source and destination point comunicate via loopback device.
I think it's not correct because if eth0 is DOWN for all the hosts in LAN should be down for me too. Or not?
Suppose another conf:
HOSTA# ifconfig
eth0 Link encap:Ethernet HWaddr 00:10:DC:C3:5E:FF
inet addr:192.168.0.1 Bcast:192.168.0.255 Mask:255.0.0.0 BROADCAST MULTICAST MTU:1500 Metric:1
eth1 Link encap:Ethernet HWaddr 00:0E:35:74:16:67
inet addr:192.168.0.2 [...]
UP BROADCAST RUNNING MULTICAST MTU:1500
lo [...]
HOSTB# ifconfig eth0
eth0 Link encap:Ethernet HWaddr 00:00:24:C8:4A:7D
inet addr:192.168.0.1 Bcast:1.255.255.255 Mask:255.0.0.0 UP BROADCAST RUNNING MULTICAST MTU:1500 [...]
So, HOSTA and HOSTB share the same ip but: HOSTA eth0 is DOWN; HOSTA eth1 is UP, HOSTB eth0 is UP. So, no conflict should be possible.
but:
HOSTB# ping 192.168.0.2
(does not reply)
So I suppose that HOSTA route the icmp reply through its lo. But:
HOSTA# tcpdump -i lo
doesn't show any reply, and
HOSTA# tcpdump -i eth0
it's not permitted, because eth0 is DOWN.
The same result for TCP protocol (tested with hping). Operative conditions: Linux 2.6.14, HOSTA eth1 is wifi. Regards
JohnnyRun
Quoted 2 lines · JohnnyRun
Hi all!
I think it's a bug....
That definately seems weired, but I never ran into it till now...
Quoted 8 lines
HOSTA# ifconfig eth0 192.168.0.1
HOSTA# ifconfig eth0 down
HOSTA# ping 192.168.0.1
(the ping works, like all other ICMP / TCP /UDP ... application. In other words: all work like eth0 in UP mode when source and destination point comunicate via loopback device.
I think it's not correct because if eth0 is DOWN for all the hosts in LAN should be down for me too. Or not?
Just to rewrite that in iproute2
old ~ # ip addr flush dev eth1
old ~ # ip addr show dev eth1
4: eth1: <BROADCAST,MULTICAST> mtu 1500 qdisc pfifo_fast qlen 1000
link/ether 00:00:00:54:0b:8a brd ff:ff:ff:ff:ff:ff
old ~ # ping -c1 -q 192.168.0.1
PING 192.168.0.1 (192.168.0.1) 56(84) bytes of data.
--- 192.168.0.1 ping statistics ---
1 packets transmitted, 0 received, 100% packet loss, time 0ms
old ~ # ip addr add 192.168.0.1/32 dev eth1
old ~ # ip link set dev eth1 down
old ~ # ip link show dev eth1
4: eth1: <BROADCAST,MULTICAST> mtu 1500 qdisc pfifo_fast qlen 1000
link/ether 00:00:00:54:0b:8a brd ff:ff:ff:ff:ff:ff
old ~ # ping -c1 -q 192.168.0.1
PING 192.168.0.1 (192.168.0.1) 56(84) bytes of data.
--- 192.168.0.1 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 0.033/0.033/0.033/0.000 ms
Quoted 27 lines
Suppose another conf:
HOSTA# ifconfig
eth0 Link encap:Ethernet HWaddr 00:10:DC:C3:5E:FF
inet addr:192.168.0.1 Bcast:192.168.0.255 Mask:255.0.0.0 BROADCAST MULTICAST MTU:1500 Metric:1
eth1 Link encap:Ethernet HWaddr 00:0E:35:74:16:67
inet addr:192.168.0.2 [...]
UP BROADCAST RUNNING MULTICAST MTU:1500
lo [...]HOSTB# ifconfig eth0
eth0 Link encap:Ethernet HWaddr 00:00:24:C8:4A:7Dinet addr:192.168.0.1 Bcast:1.255.255.255 Mask:255.0.0.0 UP BROADCAST RUNNING MULTICAST MTU:1500 [...]So, HOSTA and HOSTB share the same ip but: HOSTA eth0 is DOWN; HOSTA eth1 is UP, HOSTB eth0 is UP. So, no conflict should be possible.
but:HOSTB# ping 192.168.0.2
(does not reply)So I suppose that HOSTA route the icmp reply through its lo. But:
Quoted 8 lines
HOSTA# tcpdump -i lo
doesn't show any reply, andHOSTA# tcpdump -i eth0
it's not permitted, because eth0 is DOWN.The same result for TCP protocol (tested with hping). Operative conditions: Linux 2.6.14, HOSTA eth1 is wifi.
Very good testcase!
Any IP gurus? Ideas on why is such behaviour observerd?
Does it have to do something with the driver for ethX being notiefied of the link status and thus hardware (PHY?) is shut down so signal from the wire is ignored?
Or down the ARP somewhere?
Cannot think of security exploit at the moment, but there should be one...
Kalin.
Signature · 3 lines
|[ ~~~~~~~~~~~~~~~~~~~~~~ ]| +-> http://ThinRope.net/ <-+ |[ ______________________ ]|
Quoted 1 line · JohnnyRun
I think it's a bug....
just a link to other places where this came up:
http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=322654
Gruss
Bernd