fbdev/ssd1307fb: Some changes and improvement

PATCH Superseded Jyri Sarha 2 participants 10 messages Jan 12, 2017 3 messages not in the archive

Subsystems (4)

Device tree bindings DRM drivers DRM misc Framebuffer layer

lore

Share & tools

lore

Jyri Sarha

author

2017-01-12 11:16 UTC #0 lore raw

cover fbdev/ssd1307fb: Some changes and improvement

We needed these changes for couple of our evm. Everything else is quite straight forward, but removing the reset-active-low dts property is a questionable at least in theory. However, in practice if anyone was using the property in their device-tree blobs, they have never been able to get desired effect with mainline kernel.

Jyri Sarha (3):
fbdev: ssd1307fb: Start to use gpiod API for reset gpio
fbdev: ssd1307fb: Remove reset-active-low from the DT binding document
fbdev: ssd1307fb: Make reset gpio devicetree property optional

Tomi Valkeinen (3):
fbdev/ssd1307fb: add support to enable VBAT
fbdev/ssd1307fb: clear screen in probe
fbdev/ssd1307fb: add support to enable VBAT

 .../devicetree/bindings/display/ssd1307fb.txt      |  5 +-
 drivers/video/fbdev/ssd1307fb.c                    | 55 ++++++++++++++--------
 2 files changed, 38 insertions(+), 22 deletions(-)

Signature · 6 lines

1.9.1

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to [email protected]
More majordomo info at  http://vger.kernel.org/majordomo-info.html

A message that is not in the archive (sent off-list or not yet received): [email protected]

Jyri Sarha

author

2017-01-12 11:16 UTC #2 lore raw

PATCH 1/6 fbdev: ssd1307fb: Start to use gpiod API for reset gpio

Start to use gpiod API for reset gpio.

Signed-off-by Jyri Sarha <[email protected]>

---
 drivers/video/fbdev/ssd1307fb.c | 25 ++++++++-----------------
 1 file changed, 8 insertions(+), 17 deletions(-)

drivers/video/fbdev/ssd1307fb.c +8 ~~-17~~

index 2925d5c..8ffaaee 100644
@@ -73,7 +73,7 @@ struct ssd1307fb_par {
 	u32 prechargep2;
 	struct pwm_device *pwm;
 	u32 pwm_period;
-	int reset;
+	struct gpio_desc *reset;
 	u32 seg_remap;
 	u32 vcomh;
 	u32 width;

@@ -561,10 +561,11 @@ static int ssd1307fb_probe(struct i2c_client *client,
 
 	par->device_info = of_device_get_match_data(&client->dev);
 
-	par->reset = of_get_named_gpio(client->dev.of_node,
-					 "reset-gpios", 0);
-	if (!gpio_is_valid(par->reset)) {
-		ret = -EINVAL;
+	par->reset = devm_gpiod_get(&client->dev, "reset", GPIOD_OUT_LOW);
+	if (IS_ERR(par->reset)) {
+		dev_err(&client->dev, "failed to get reset gpio: %ld\n",
+			PTR_ERR(par->reset));
+		ret = PTR_ERR(par->reset);
 		goto fb_alloc_error;
 	}

@@ -642,22 +643,12 @@ static int ssd1307fb_probe(struct i2c_client *client,
 
 	fb_deferred_io_init(info);
 
-	ret = devm_gpio_request_one(&client->dev, par->reset,
-				    GPIOF_OUT_INIT_HIGH,
-				    "oled-reset");
-	if (ret) {
-		dev_err(&client->dev,
-			"failed to request gpio %d: %d\n",
-			par->reset, ret);
-		goto reset_oled_error;
-	}
-
 	i2c_set_clientdata(client, info);
 
 	/* Reset the screen */
-	gpio_set_value(par->reset, 0);
+	gpiod_set_value(par->reset, 0);
 	udelay(4);
-	gpio_set_value(par->reset, 1);
+	gpiod_set_value(par->reset, 1);
 	udelay(4);
 
 	ret = ssd1307fb_init(par);

Signature · 6 lines

1.9.1

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to [email protected]
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Jyri Sarha

author

2017-01-12 11:16 UTC #3 lore raw

PATCH 2/6 fbdev: ssd1307fb: Remove reset-active-low from the DT binding document

In reply to a message not in the archive

Remove reset-active-low from the devicetree binding document. The actual implementation has never been there in the driver code and there is no reason to add it because the gpiod API supports gpio flags, including GPIO_ACTIVE_LOW, directly trough its own devicetree binding.

Signed-off-by Jyri Sarha <[email protected]>

---
 Documentation/devicetree/bindings/display/ssd1307fb.txt | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

Documentation/devicetree/bindings/display/ssd1307fb.txt +2 -2

index eb31ed4..4aee67f 100644
@@ -8,14 +8,14 @@ Required properties:
          0x3c or 0x3d
   - pwm: Should contain the pwm to use according to the OF device tree PWM
          specification [0]. Only required for the ssd1307.
-  - reset-gpios: Should contain the GPIO used to reset the OLED display
+  - reset-gpios: Should contain the GPIO used to reset the OLED display. See
+                 Documentation/devicetree/bindings/gpio/gpio.txt for details.
   - solomon,height: Height in pixel of the screen driven by the controller
   - solomon,width: Width in pixel of the screen driven by the controller
   - solomon,page-offset: Offset of pages (band of 8 pixels) that the screen is
     mapped to.
 
 Optional properties:
-  - reset-active-low: Is the reset gpio is active on physical low?
   - solomon,segment-no-remap: Display needs normal (non-inverted) data column
                               to segment mapping
   - solomon,com-seq: Display uses sequential COM pin configuration

Signature · 6 lines

1.9.1

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to [email protected]
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Jyri Sarha

author

2017-01-12 11:16 UTC #4 lore raw

PATCH 3/6 fbdev: ssd1307fb: Make reset gpio devicetree property optional

In reply to a message not in the archive

Make reset gpio devicetree property optional. Depending on the board designing there may not be a dedicated gpio for resetting the display. Without a proper reset there may be some junk in the display memory at probe time, so in such a case the display memory is cleared before turning it on. The devicetree binding document is also updated.

Signed-off-by Jyri Sarha <[email protected]>

---
 .../devicetree/bindings/display/ssd1307fb.txt         |  4 ++--
 drivers/video/fbdev/ssd1307fb.c                       | 19 +++++++++++++------
 2 files changed, 15 insertions(+), 8 deletions(-)

Documentation/devicetree/bindings/display/ssd1307fb.txt +2 -2

index 4aee67f..6617df6 100644
@@ -8,14 +8,14 @@ Required properties:
          0x3c or 0x3d
   - pwm: Should contain the pwm to use according to the OF device tree PWM
          specification [0]. Only required for the ssd1307.
-  - reset-gpios: Should contain the GPIO used to reset the OLED display. See
-                 Documentation/devicetree/bindings/gpio/gpio.txt for details.
   - solomon,height: Height in pixel of the screen driven by the controller
   - solomon,width: Width in pixel of the screen driven by the controller
   - solomon,page-offset: Offset of pages (band of 8 pixels) that the screen is
     mapped to.
 
 Optional properties:
+  - reset-gpios: The GPIO used to reset the OLED display, if available. See
+                 Documentation/devicetree/bindings/gpio/gpio.txt for details.
   - solomon,segment-no-remap: Display needs normal (non-inverted) data column
                               to segment mapping
   - solomon,com-seq: Display uses sequential COM pin configuration

drivers/video/fbdev/ssd1307fb.c +13 -6

index 8ffaaee..89372af 100644
@@ -439,6 +439,10 @@ static int ssd1307fb_init(struct ssd1307fb_par *par)
 	if (ret < 0)
 		return ret;
 
+	/* Clear the screen if we could not give reset at probe time */
+	if (!par->reset)
+		ssd1307fb_update_display(par);
+
 	/* Turn on the display */
 	ret = ssd1307fb_write_cmd(par->client, SSD1307FB_DISPLAY_ON);
 	if (ret < 0)

@@ -561,7 +565,8 @@ static int ssd1307fb_probe(struct i2c_client *client,
 
 	par->device_info = of_device_get_match_data(&client->dev);
 
-	par->reset = devm_gpiod_get(&client->dev, "reset", GPIOD_OUT_LOW);
+	par->reset = devm_gpiod_get_optional(&client->dev, "reset",
+					     GPIOD_OUT_LOW);
 	if (IS_ERR(par->reset)) {
 		dev_err(&client->dev, "failed to get reset gpio: %ld\n",
 			PTR_ERR(par->reset));

@@ -645,11 +650,13 @@ static int ssd1307fb_probe(struct i2c_client *client,
 
 	i2c_set_clientdata(client, info);
 
-	/* Reset the screen */
-	gpiod_set_value(par->reset, 0);
-	udelay(4);
-	gpiod_set_value(par->reset, 1);
-	udelay(4);
+	if (par->reset) {
+		/* Reset the screen */
+		gpiod_set_value(par->reset, 0);
+		udelay(4);
+		gpiod_set_value(par->reset, 1);
+		udelay(4);
+	}
 
 	ret = ssd1307fb_init(par);
 	if (ret)

Signature · 6 lines

1.9.1

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to [email protected]
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Jyri Sarha

author

2017-01-12 11:16 UTC #5 lore raw

PATCH 4/6 fbdev/ssd1307fb: add support to enable VBAT

In reply to a message not in the archive

From: Tomi Valkeinen <[email protected]>

SSD1306 needs VBAT when it is wired in charge pump configuration. This patch adds support to the driver to enable VBAT regulator at init time.

Signed-off-by Tomi Valkeinen <[email protected]>

Signed-off-by Jyri Sarha <[email protected]>

---
 drivers/video/fbdev/ssd1307fb.c | 20 +++++++++++++++++++-
 1 file changed, 19 insertions(+), 1 deletion(-)

drivers/video/fbdev/ssd1307fb.c +19 -1

index 89372af..616a6a3 100644
@@ -16,6 +16,7 @@
 #include <linux/of_gpio.h>
 #include <linux/pwm.h>
 #include <linux/uaccess.h>
+#include <linux/regulator/consumer.h>
 
 #define SSD1307FB_DATA			0x40
 #define SSD1307FB_COMMAND		0x80

@@ -74,6 +75,7 @@ struct ssd1307fb_par {
 	struct pwm_device *pwm;
 	u32 pwm_period;
 	struct gpio_desc *reset;
+	struct regulator *vbat_reg;
 	u32 seg_remap;
 	u32 vcomh;
 	u32 width;

@@ -574,6 +576,14 @@ static int ssd1307fb_probe(struct i2c_client *client,
 		goto fb_alloc_error;
 	}
 
+	par->vbat_reg = devm_regulator_get_optional(&client->dev, "vbat");
+	if (IS_ERR(par->vbat_reg)) {
+		dev_err(&client->dev, "failed to get VBAT regulator: %ld\n",
+			PTR_ERR(par->vbat_reg));
+		ret = PTR_ERR(par->vbat_reg);
+		goto fb_alloc_error;
+	}
+
 	if (of_property_read_u32(node, "solomon,width", &par->width))
 		par->width = 96;

@@ -658,9 +668,15 @@ static int ssd1307fb_probe(struct i2c_client *client,
 		udelay(4);
 	}
 
+	ret = regulator_enable(par->vbat_reg);
+	if (ret) {
+		dev_err(&client->dev, "failed to enable VBAT: %d\n", ret);
+		goto reset_oled_error;
+	}
+
 	ret = ssd1307fb_init(par);
 	if (ret)
-		goto reset_oled_error;
+		goto regulator_enable_error;
 
 	ret = register_framebuffer(info);
 	if (ret) {

@@ -693,6 +709,8 @@ static int ssd1307fb_probe(struct i2c_client *client,
 		pwm_disable(par->pwm);
 		pwm_put(par->pwm);
 	};
+regulator_enable_error:
+	regulator_disable(par->vbat_reg);
 reset_oled_error:
 	fb_deferred_io_cleanup(info);
 fb_alloc_error:

Signature · 6 lines

1.9.1

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to [email protected]
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Jyri Sarha

author

2017-01-12 11:16 UTC #6 lore raw

PATCH 5/6 fbdev/ssd1307fb: clear screen in probe

In reply to a message not in the archive

From: Tomi Valkeinen <[email protected]>

SSD1306 does not clear the panel's framebuffer automatically, even if a HW reset happens, so we need to do that at probe time before enabling the panel.

Signed-off-by Tomi Valkeinen <[email protected]>

Signed-off-by Jyri Sarha <[email protected]>

---
 drivers/video/fbdev/ssd1307fb.c | 5 ++---
 1 file changed, 2 insertions(+), 3 deletions(-)

drivers/video/fbdev/ssd1307fb.c +2 -3

index 616a6a3..5c87ae4 100644
@@ -441,9 +441,8 @@ static int ssd1307fb_init(struct ssd1307fb_par *par)
 	if (ret < 0)
 		return ret;
 
-	/* Clear the screen if we could not give reset at probe time */
-	if (!par->reset)
-		ssd1307fb_update_display(par);
+	/* Clear the screen */
+	ssd1307fb_update_display(par);
 
 	/* Turn on the display */
 	ret = ssd1307fb_write_cmd(par->client, SSD1307FB_DISPLAY_ON);

Signature · 6 lines

1.9.1

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to [email protected]
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Jyri Sarha

author

2017-01-12 11:16 UTC #7 lore raw

PATCH 6/6 fbdev/ssd1307fb: add support to enable VBAT

In reply to a message not in the archive

From: Tomi Valkeinen <[email protected]>

SSD1306 needs VBAT when it is wired in charge pump configuration. This patch adds support to the driver to enable VBAT regulator at init time.

Signed-off-by Tomi Valkeinen <[email protected]>

Reviewed-by Roger Quadros <[email protected]>

Signed-off-by Jyri Sarha <[email protected]>

---
 Documentation/devicetree/bindings/display/ssd1307fb.txt | 1 +
 1 file changed, 1 insertion(+)

Documentation/devicetree/bindings/display/ssd1307fb.txt +1 -0

index 6617df6..209d931 100644
@@ -16,6 +16,7 @@ Required properties:
 Optional properties:
   - reset-gpios: The GPIO used to reset the OLED display, if available. See
                  Documentation/devicetree/bindings/gpio/gpio.txt for details.
+  - vbat-supply: The supply for VBAT
   - solomon,segment-no-remap: Display needs normal (non-inverted) data column
                               to segment mapping
   - solomon,com-seq: Display uses sequential COM pin configuration

Signature · 6 lines

1.9.1

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to [email protected]
More majordomo info at  http://vger.kernel.org/majordomo-info.html

A message that is not in the archive (sent off-list or not yet received): c394e52447ed45fff9672eb3e3bb6729bea87ee7.1484219137.git.jsarha-l0cyMroinI0@public.gmane.org

Tomi Valkeinen

2017-01-12 12:05 UTC #9 lore raw

Re: [PATCH 6/6] fbdev/ssd1307fb: add support to enable VBAT

Quoted 18 lines · Jyri Sarha

From: Tomi Valkeinen <[email protected]>
SSD1306 needs VBAT when it is wired in charge pump configuration. This patch adds support to the driver to enable VBAT regulator at init time.
Signed-off-by Tomi Valkeinen <[email protected]>
Reviewed-by Roger Quadros <[email protected]>
Signed-off-by Jyri Sarha <[email protected]>
---
 Documentation/devicetree/bindings/display/ssd1307fb.txt | 1 +
 1 file changed, 1 insertion(+)
Documentation/devicetree/bindings/display/ssd1307fb.txt +0 -0
index 6617df6..209d931 100644

Documentation/devicetree/bindings/display/ssd1307fb.txt Required properties: · line 22

Quoted 7 lines

Documentation/devicetree/bindings/display/ssd1307fb.txt +1 -0

@@ -16,6 +16,7 @@ Required properties:
 Optional properties:
   - reset-gpios: The GPIO used to reset the OLED display, if available. See
                  Documentation/devicetree/bindings/gpio/gpio.txt for details.
+  - vbat-supply: The supply for VBAT
   - solomon,segment-no-remap: Display needs normal (non-inverted) data column
                               to segment mapping
   - solomon,com-seq: Display uses sequential COM pin configuration

It's rather confusing to have two patches with identical subjects and descs (this and 4). And there's even an unrelated patch in between this and the driver change...

Tomi

A message that is not in the archive (sent off-list or not yet received): d06c3a64-7627-2553-84e5-491a5acbe0de-l0cyMroinI0@public.gmane.org

Jyri Sarha

author

2017-01-12 13:46 UTC #11 lore raw

Re: [PATCH 6/6] fbdev/ssd1307fb: add support to enable VBAT

Quoted 22 lines · Tomi Valkeinen

Quoted 21 lines · Jyri Sarha
From: Tomi Valkeinen <[email protected]>
SSD1306 needs VBAT when it is wired in charge pump configuration. This patch adds support to the driver to enable VBAT regulator at init time.
Signed-off-by Tomi Valkeinen <[email protected]>
Reviewed-by Roger Quadros <[email protected]>
Signed-off-by Jyri Sarha <[email protected]>
---
 Documentation/devicetree/bindings/display/ssd1307fb.txt | 1 +
 1 file changed, 1 insertion(+)
Documentation/devicetree/bindings/display/ssd1307fb.txt +1 -0
index 6617df6..209d931 100644
@@ -16,6 +16,7 @@ Required properties:
 Optional properties:
   - reset-gpios: The GPIO used to reset the OLED display, if available. See
                  Documentation/devicetree/bindings/gpio/gpio.txt for details.
+  - vbat-supply: The supply for VBAT

Quoted 9 lines

Documentation/devicetree/bindings/display/ssd1307fb.txt Required properties: · line 22
Quoted 4 lines
Documentation/devicetree/bindings/display/ssd1307fb.txt +0 -0
   - solomon,segment-no-remap: Display needs normal (non-inverted) data column
                               to segment mapping
   - solomon,com-seq: Display uses sequential COM pin configuration
It's rather confusing to have two patches with identical subjects and descs (this and 4). And there's even an unrelated patch in between this and the driver change...

Argh. I wonder how did this even happen. Something weird must have been going on... there is only one such patch in branch I cherry-picked these patches from. These last patches did not give me any errors and compiled fine, so did not look too carefully at the results. Anyway, I'll squash this into the earlier patch with the same subject in version 2 series.

Best regards,
Jyri

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to [email protected] More majordomo info at http://vger.kernel.org/majordomo-info.html

Jyri Sarha

author

2017-01-12 11:27 UTC #12 lore raw

In reply to a message not in the archive

I did not notice the latest update on MAINTAINERS when sending this
series. Added Bartlomiej Zolnierkiewicz <[email protected]> to loop.

Quoted 11 lines · Jyri Sarha

We needed these changes for couple of our evm. Everything else is quite straight forward, but removing the reset-active-low dts property is a questionable at least in theory. However, in practice if anyone was using the property in their device-tree blobs, they have never been able to get desired effect with mainline kernel.
Jyri Sarha (3):
fbdev: ssd1307fb: Start to use gpiod API for reset gpio
fbdev: ssd1307fb: Remove reset-active-low from the DT binding document
fbdev: ssd1307fb: Make reset gpio devicetree property optional

Quoted 9 lines

Tomi Valkeinen (3):
fbdev/ssd1307fb: add support to enable VBAT
fbdev/ssd1307fb: clear screen in probe
fbdev/ssd1307fb: add support to enable VBAT
 .../devicetree/bindings/display/ssd1307fb.txt      |  5 +-
 drivers/video/fbdev/ssd1307fb.c                    | 55 ++++++++++++++--------
 2 files changed, 38 insertions(+), 22 deletions(-)

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to [email protected] More majordomo info at http://vger.kernel.org/majordomo-info.html