iio: adc: ad7791: fix IRQ flags
Subsystems (2)
Nuno Sá
maintainerPATCH 1/1 iio: adc: ad7791: fix IRQ flags
The interrupt is triggered on the falling edge rather than being a level low interrupt.
--- drivers/iio/adc/ad7791.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/iio/adc/ad7791.c +1 -1
@@ -253,7 +253,7 @@ static const struct ad_sigma_delta_info ad7791_sigma_delta_info = { .has_registers = true, .addr_shift = 4, .read_mask = BIT(3), - .irq_flags = IRQF_TRIGGER_LOW, + .irq_flags = IRQF_TRIGGER_FALLING, }; static int ad7791_read_raw(struct iio_dev *indio_dev,
Signature · 1 line
2.39.1
Jonathan Cameron
maintainerQuoted 5 lines · On Fri, 20 Jan 2023 13:46:45 +0100 Nuno Sá <[email protected]> wrote:
The interrupt is triggered on the falling edge rather than being a level low interrupt.
Fixes da4d3d6bb9f6 ("iio: adc: ad-sigma-delta: Allow custom IRQ flags")Signed-off-by Nuno Sá <[email protected]>
What are the symptoms of this? Given the ad_sigma_delta.c irq handler disables the interrupt until after the data read is done (at which point the level is presumably high again), I don't immediately see why the change here has any impact - either we trigger on the fall, or on the fact it has become low..
Or is there a board other there that only does end interrupts that is causing problems?
Jonathan
Quoted 17 lines
--- drivers/iio/adc/ad7791.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)drivers/iio/adc/ad7791.c +1
-1@@ -253,7 +253,7 @@ static const struct ad_sigma_delta_info ad7791_sigma_delta_info = { .has_registers = true, .addr_shift = 4, .read_mask = BIT(3), - .irq_flags = IRQF_TRIGGER_LOW, + .irq_flags = IRQF_TRIGGER_FALLING, }; static int ad7791_read_raw(struct iio_dev *indio_dev,
Quoted 11 lines · Jonathan Cameron
Quoted 7 lines · On Fri, 20 Jan 2023 13:46:45 +0100 Nuno Sá <[email protected]> wrote:
The interrupt is triggered on the falling edge rather than being a level
low interrupt.Fixes da4d3d6bb9f6 ("iio: adc: ad-sigma-delta: Allow custom IRQflags")
Signed-off-by Nuno Sá <[email protected]>
Quoted 11 lines
What are the symptoms of this? Given the
ad_sigma_delta.cirq handler
disables the interrupt until after the data read is done (at which point the
level is presumably high again), I don't immediately see why the change
here has any impact - either we trigger on the fall, or on the fact it
has become low..
Honestly I did not checked this in any HW. This was just by inspecting the datasheet and confirming that the LOW IRQ is not coherent with what we have in other sigma delta ADCs.
However, after some git blaming, I found this [1] which shows that this might be an issue...
Hmm, maybe makes sense to add a link to the bellow patch in the commit description...
[1]:https://lore.kernel.org/linux-iio/[email protected]/
- Nuno Sá
Quoted 43 lines · Nuno Sá
Quoted 12 lines · Jonathan Cameron
Quoted 8 lines · On Fri, 20 Jan 2023 13:46:45 +0100 Nuno Sá <[email protected]> wrote:
The interrupt is triggered on the falling edge rather than being a
level
low interrupt.Fixes da4d3d6bb9f6 ("iio: adc: ad-sigma-delta: Allow custom IRQflags")
Signed-off-by Nuno Sá <[email protected]>Quoted 11 lines
What are the symptoms of this? Given the
ad_sigma_delta.cirq handler
disables the interrupt until after the data read is done (at which point the
level is presumably high again), I don't immediately see why the change
here has any impact - either we trigger on the fall, or on the fact it
has become low..Honestly I did not checked this in any HW. This was just by inspecting
the datasheet and confirming that the LOW IRQ is not coherent with what
we have in other sigma delta ADCs.However, after some git blaming, I found this [1] which shows that this
might be an issue...Hmm, maybe makes sense to add a link to the bellow patch in the commit
description...
[1]:
https://lore.kernel.org/linux-iio/[email protected]
/
Quoted 1 line
- Nuno Sá
Hi Jonathan,
Anything that I should do in this one? As I did not tested it, it might not be a real issue but I still think the patch is good even though it might not deserve a Fixes tag...
- Nuno Sá
Quoted 46 lines · On Mon, 06 Feb 2023 12:13:50 +0100 Nuno Sá <[email protected]> wrote:
Quoted 43 lines · Nuno Sá
Quoted 12 lines · Jonathan Cameron
Quoted 8 lines · On Fri, 20 Jan 2023 13:46:45 +0100 Nuno Sá <[email protected]> wrote:
The interrupt is triggered on the falling edge rather than being a
level
low interrupt.Fixes da4d3d6bb9f6 ("iio: adc: ad-sigma-delta: Allow custom IRQflags")
Signed-off-by Nuno Sá <[email protected]>Quoted 11 lines
What are the symptoms of this? Given the
ad_sigma_delta.cirq handler
disables the interrupt until after the data read is done (at which point the
level is presumably high again), I don't immediately see why the change
here has any impact - either we trigger on the fall, or on the fact it
has become low..Honestly I did not checked this in any HW. This was just by inspecting
the datasheet and confirming that the LOW IRQ is not coherent with what
we have in other sigma delta ADCs.However, after some git blaming, I found this [1] which shows that this
might be an issue...Hmm, maybe makes sense to add a link to the bellow patch in the commit
description...
[1]:
https://lore.kernel.org/linux-iio/[email protected]
/Quoted 1 line
- Nuno Sá
Quoted 7 lines
Hi Jonathan,
Anything that I should do in this one? As I did not tested it, it might not be a real issue but I still think the patch is good even though it might not deserve a Fixes tag...
- Nuno Sá
Applied to the fixes-togreg rbanch of iio.git. I left the fixes tag but just to be awkward didn't mark it for stable (it'll get picked up anyway probably but I didn't want to imply there was any rush in doing so ;)
Thanks,
Jonathan