Skip to contentSkip to conversation

: net: dsa: mt7530: support MT7530 in the MT7621 So

PATCH Superseded [email protected] 3 participants 13 messages Jan 14, 2019 – Jan 17, 2019

Subsystems (7)

v2 of 4 Superseded Latest is v4 →

lore
Share & tools
lore
#0 lore raw

v2 cover : net: dsa: mt7530: support MT7530 in the MT7621 So

This is the second version of a patch series supporting the MT7530 switch as used in the MediaTek MT7621 SoC. Unlike the MediaTek MT7623 the MT7621 is built around a dual core MIPS CPU architecture. But inside it uses basically the same 7530 switch.

These patches resolves all issues I had with version 1, and I can now reliably use the driver on a 7621 SoC platform. These patches were generated against linux-5.0-rc2.

The first 2 patches are new to the series and enable support for the existing kernel mediatek ethernet driver on the MT7621 SoC. This support is from Bjørn Mork, with an update and fix by me. Using this driver fixed a number of problems I had (TX checksums, large RX packet drop) over the staging driver (drivers/staging/mt7621-eth).

Patch 3 modifies the mt7530 DSA driver to support the 7530 switch as implemented in the Mediatek MT7621 SoC. The last patch updates the devicetree bindings to reflect the new support in the mt7530 driver.

Creating a new binding for the MT7621 seems like the only viable approach to distinguish between a stand alone 7530 switch, the silicon module in the MT7623 SoC and the silicon in the MT7621. Certainly the 7530 ID register in the MT7623 and MT7621 returns the same value, "0x7530001".

Looking at the mt7530.c DSA driver it might make seom sense to convert the existing "mediatek,mcm" binding to something like "mediatek,mt7623" to be consistent with this new MT7621 support. As far as I can tell this is the intention of this binding.

Any thoughts greatly appreciated...

 Documentation/devicetree/bindings/net/dsa/mt7530.txt |    3
 drivers/net/dsa/mt7530.c                             |   97 +++++++++++--------
 drivers/net/dsa/mt7530.h                             |    9 +
 drivers/net/ethernet/mediatek/Kconfig                |    2
 drivers/net/ethernet/mediatek/mtk_eth_soc.c          |   49 ++++++++-
 drivers/net/ethernet/mediatek/mtk_eth_soc.h          |    4
 6 files changed, 115 insertions(+), 49 deletions(-)

v1: initial patch series
v2: rebase to linux-5.0-rc2
include mediatek ethernet driver changes change to use devicetree binding to idenify platform

#1 lore raw

PATCH v2 1/4 net: ethernet: mediatek: support MT7621 SoC ethernet hardware

From: Bjørn Mork <[email protected]>

The Mediatek MT7621 SoC contains the same ethernet hardware module as used on a number of other MediaTek SoC parts. There are some minor differences to deal with but we can use the same driver to support them all.

This patch is based on work by Bjørn Mork <[email protected]>, and his original patch is at:

https://github.com/bmork/LEDE/commit/3293bc63f5461ca1eb0bbc4ed90145335e7e3404

There is an additional compatible devicetree type added, and the primary change to the code required is to support a single interrupt (for both RX and TX interrupts).

[[email protected]: rebase to mainline and irq handler fix]
---
 drivers/net/ethernet/mediatek/Kconfig       |  2 +-
 drivers/net/ethernet/mediatek/mtk_eth_soc.c | 48 ++++++++++++++++++---
 drivers/net/ethernet/mediatek/mtk_eth_soc.h |  4 ++
 3 files changed, 46 insertions(+), 8 deletions(-)

v2: first patch in this series for this change

drivers/net/ethernet/mediatek/Kconfig +1 -1
index f9149d2a4694..43656f961891 100644
@@ -1,6 +1,6 @@
 config NET_VENDOR_MEDIATEK
 	bool "MediaTek ethernet driver"
-	depends on ARCH_MEDIATEK
+	depends on ARCH_MEDIATEK || SOC_MT7621
 	---help---
 	  If you have a Mediatek SoC with ethernet, say Y.
 
drivers/net/ethernet/mediatek/mtk_eth_soc.c +41 -7

79 lines not on this page · raw message

drivers/net/ethernet/mediatek/mtk_eth_soc.h +4 -0
index 46819297fc3e..f7501997cea0 100644
@@ -363,6 +363,7 @@
 #define ETHSYS_CHIPID4_7	0x4
 #define MT7623_ETH		7623
 #define MT7622_ETH		7622
+#define MT7621_ETH		7621
 
 /* ethernet subsystem config register */
 #define ETHSYS_SYSCFG0		0x14
@@ -488,6 +489,8 @@ enum mtk_clks_map {
 				 BIT(MTK_CLK_SGMII_CDR_FB) | \
 				 BIT(MTK_CLK_SGMII_CK) | \
 				 BIT(MTK_CLK_ETH2PLL))
+#define MT7621_CLKS_BITMAP	(0)
+
 enum mtk_dev_state {
 	MTK_HW_INIT,
 	MTK_RESETTING
@@ -567,6 +570,7 @@ struct mtk_rx_ring {
 #define MTK_DUAL_GMAC_SHARED_SGMII	(BIT(11) | MTK_GMAC1_SGMII | \
 					 MTK_GMAC2_SGMII)
 #define MTK_HWLRO			BIT(12)
+#define MTK_SHARED_INT			BIT(13)
 #define MTK_HAS_CAPS(caps, _x)		(((caps) & (_x)) == (_x))
 
 /* struct mtk_eth_data -	This is the structure holding all differences
Signature · 1 line
2.17.1
#2 lore raw

PATCH v2 2/4 net: ethernet: mediatek: do not force autonegiation at init

In reply to [email protected]

From: Greg Ungerer <[email protected]>

Do not attempt to force a port phy auto-ngeotiation during the driver init phase. It is not necessary and results in a warning at system boot up:

mtk_soc_eth 1e100000.ethernet: generated random MAC address be:e7:d4:9d:7d:b0 mtk_soc_eth 1e100000.ethernet: connected mac 0 to PHY at fixed-0:00 [uid=00000000, driver=Generic PHY]

------------[ cut here ]------------
WARNING: CPU: 1 PID: 1 at drivers/net/phy/phy.c:548 phy_start_aneg+0xf0/0x1c0
called from state READY
Modules linked in:
CPU: 1 PID: 1 Comm: swapper/0 Not tainted 5.0.0-rc1-00005-ge3368ed2e336-dirty #11
Stack : 0000007a 00000000 00000000 807e0000 80710000 8006fb04 8072db28 0000000b
        00000000 00000000 8072d368 87c3db74 80770000 00000001 87c3db08 2892b90e
        00000000 00000000 80820000 00000000 00000000 2d363333 0000007b 00000000
        2d316372 00000000 00000000 00000000 80770000 00000000 80715e70 00000009
        00000224 80716e38 87d6a800 80660334 00000001 80340714 00000004 807e0004
        ...
Call Trace:
[<8000cfe0>] show_stack+0x94/0x12c
[<8060de6c>] dump_stack+0x8c/0xd0
[<80028430>] __warn+0x10c/0x120
[<80028488>] warn_slowpath_fmt+0x44/0x68
[<803adf78>] phy_start_aneg+0xf0/0x1c0
[<807aed8c>] mtk_init+0x434/0x4a4
[<8047310c>] register_netdevice+0x94/0x6d0
[<8047376c>] register_netdev+0x24/0x40
[<803bf4c0>] mtk_probe+0x2a0/0x930
[<80352d24>] platform_drv_probe+0x40/0x9c
[<80350e48>] really_probe+0x1f0/0x35c
[<803513e4>] __driver_attach+0x10c/0x114
[<8034ec88>] bus_for_each_dev+0x70/0xd0
[<8035023c>] bus_add_driver+0x1f0/0x25c
[<80351c70>] driver_register+0x80/0x144
[<800015f4>] do_one_initcall+0x50/0x1ac
[<80795e48>] kernel_init_freeable+0x184/0x26c
[<8062bbd4>] kernel_init+0x14/0x110
[<80007198>] ret_from_kernel_thread+0x14/0x1c
---[ end trace 6e884e9f12ed14c0 ]---

mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 22

---
 drivers/net/ethernet/mediatek/mtk_eth_soc.c | 1 -
 1 file changed, 1 deletion(-)

v2: first patch in this series for this change

drivers/net/ethernet/mediatek/mtk_eth_soc.c +0 -1
index c7763a189619..e5a32d43a71c 100644
@@ -356,7 +356,6 @@ static int mtk_phy_connect(struct net_device *dev)
 	linkmode_copy(dev->phydev->advertising, dev->phydev->supported);
 	linkmode_set_bit(ETHTOOL_LINK_MODE_Autoneg_BIT,
 			 dev->phydev->advertising);
-	phy_start_aneg(dev->phydev);
 
 	of_node_put(np);
 
Signature · 1 line
2.17.1
#3 lore raw

Re: [PATCHv2 2/4] net: ethernet: mediatek: do not force autonegiation at init

Quoting [email protected]:

Quoted 66 lines

From: Greg Ungerer <[email protected]>

Do not attempt to force a port phy auto-ngeotiation during the driver init phase. It is not necessary and results in a warning at system boot up:

mtk_soc_eth 1e100000.ethernet: generated random MAC address be:e7:d4:9d:7d:b0 mtk_soc_eth 1e100000.ethernet: connected mac 0 to PHY at fixed-0:00 [uid=00000000, driver=Generic PHY]

------------[ cut here ]------------
WARNING: CPU: 1 PID: 1 at drivers/net/phy/phy.c:548 phy_start_aneg+0xf0/0x1c0
called from state READY
Modules linked in:
CPU: 1 PID: 1 Comm: swapper/0 Not tainted 5.0.0-rc1-00005-ge3368ed2e336-dirty #11
Stack : 0000007a 00000000 00000000 807e0000 80710000 8006fb04 8072db28 0000000b
        00000000 00000000 8072d368 87c3db74 80770000 00000001  
87c3db08 2892b90e
        00000000 00000000 80820000 00000000 00000000 2d363333  
0000007b 00000000
        2d316372 00000000 00000000 00000000 80770000 00000000  
80715e70 00000009
        00000224 80716e38 87d6a800 80660334 00000001 80340714  
00000004 807e0004
        ...
Call Trace:
[<8000cfe0>] show_stack+0x94/0x12c
[<8060de6c>] dump_stack+0x8c/0xd0
[<80028430>] __warn+0x10c/0x120
[<80028488>] warn_slowpath_fmt+0x44/0x68
[<803adf78>] phy_start_aneg+0xf0/0x1c0
[<807aed8c>] mtk_init+0x434/0x4a4
[<8047310c>] register_netdevice+0x94/0x6d0
[<8047376c>] register_netdev+0x24/0x40
[<803bf4c0>] mtk_probe+0x2a0/0x930
[<80352d24>] platform_drv_probe+0x40/0x9c
[<80350e48>] really_probe+0x1f0/0x35c
[<803513e4>] __driver_attach+0x10c/0x114
[<8034ec88>] bus_for_each_dev+0x70/0xd0
[<8035023c>] bus_add_driver+0x1f0/0x25c
[<80351c70>] driver_register+0x80/0x144
[<800015f4>] do_one_initcall+0x50/0x1ac
[<80795e48>] kernel_init_freeable+0x184/0x26c
[<8062bbd4>] kernel_init+0x14/0x110
[<80007198>] ret_from_kernel_thread+0x14/0x1c
---[ end trace 6e884e9f12ed14c0 ]---

mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 22

---
 drivers/net/ethernet/mediatek/mtk_eth_soc.c | 1 -
 1 file changed, 1 deletion(-)

v2: first patch in this series for this change

drivers/net/ethernet/mediatek/mtk_eth_soc.c +0 -2
index c7763a189619..e5a32d43a71c 100644
@@ -356,7 +356,6 @@ static int mtk_phy_connect(struct net_device *dev)
 	linkmode_copy(dev->phydev->advertising, dev->phydev->supported);
 	linkmode_set_bit(ETHTOOL_LINK_MODE_Autoneg_BIT,
 			 dev->phydev->advertising);
-	phy_start_aneg(dev->phydev);
 
 	of_node_put(np);
 
--
Quoted 1 line

2.17.1

Hi Greg,

I think this is recently fix and applied, see https://patchwork.kernel.org/patch/10753537/

Greats,

René

#4 lore raw

Re: [PATCHv2 2/4] net: ethernet: mediatek: do not force autonegiation at init

Hi René,

Quoted 61 lines · René van Dorst

Quoting [email protected]:

Quoted 59 lines

From: Greg Ungerer <[email protected]>

Do not attempt to force a port phy auto-ngeotiation during the driver init phase. It is not necessary and results in a warning at system boot up:

mtk_soc_eth 1e100000.ethernet: generated random MAC address be:e7:d4:9d:7d:b0 mtk_soc_eth 1e100000.ethernet: connected mac 0 to PHY at fixed-0:00 [uid=00000000, driver=Generic PHY]

------------[ cut here ]------------
WARNING: CPU: 1 PID: 1 at drivers/net/phy/phy.c:548 phy_start_aneg+0xf0/0x1c0
called from state READY
Modules linked in:
CPU: 1 PID: 1 Comm: swapper/0 Not tainted 5.0.0-rc1-00005-ge3368ed2e336-dirty #11

Stack : 0000007a 00000000 00000000 807e0000 80710000 8006fb04 8072db28 0000000b 00000000 00000000 8072d368 87c3db74 80770000 00000001 87c3db08 2892b90e 00000000 00000000 80820000 00000000 00000000 2d363333 0000007b 00000000 2d316372 00000000 00000000 00000000 80770000 00000000 80715e70 00000009 00000224 80716e38 87d6a800 80660334 00000001 80340714 00000004 807e0004
        ...

Call Trace:
[<8000cfe0>] show_stack+0x94/0x12c
[<8060de6c>] dump_stack+0x8c/0xd0
[<80028430>] __warn+0x10c/0x120
[<80028488>] warn_slowpath_fmt+0x44/0x68
[<803adf78>] phy_start_aneg+0xf0/0x1c0
[<807aed8c>] mtk_init+0x434/0x4a4
[<8047310c>] register_netdevice+0x94/0x6d0
[<8047376c>] register_netdev+0x24/0x40
[<803bf4c0>] mtk_probe+0x2a0/0x930
[<80352d24>] platform_drv_probe+0x40/0x9c
[<80350e48>] really_probe+0x1f0/0x35c
[<803513e4>] __driver_attach+0x10c/0x114
[<8034ec88>] bus_for_each_dev+0x70/0xd0
[<8035023c>] bus_add_driver+0x1f0/0x25c
[<80351c70>] driver_register+0x80/0x144
[<800015f4>] do_one_initcall+0x50/0x1ac
[<80795e48>] kernel_init_freeable+0x184/0x26c
[<8062bbd4>] kernel_init+0x14/0x110
[<80007198>] ret_from_kernel_thread+0x14/0x1c
---[ end trace 6e884e9f12ed14c0 ]---

mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 22

---
 drivers/net/ethernet/mediatek/mtk_eth_soc.c | 1 -

 1 file changed, 1 deletion(-)

v2: first patch in this series for this change

drivers/net/ethernet/mediatek/mtk_eth_soc.c +0 -1
index c7763a189619..e5a32d43a71c 100644
@@ -356,7 +356,6 @@ static int mtk_phy_connect(struct net_device *dev)
      linkmode_copy(dev->phydev->advertising, dev->phydev->supported);
      linkmode_set_bit(ETHTOOL_LINK_MODE_Autoneg_BIT,
               dev->phydev->advertising);
-    phy_start_aneg(dev->phydev);
 
Quoted 8 lines
Quoted 4 lines
drivers/net/ethernet/mediatek/mtk_eth_soc.c +0 -0
      of_node_put(np);
 
Signature · 1 line
2.17.1

Hi Greg,

I think this is recently fix and applied, see https://patchwork.kernel.org/patch/10753537/

Yep, looks like that will do it. I will drop this one.

Regards
Greg

#5 lore raw

PATCH v2 3/4 net: dsa: mt7530: support the 7530 switch on the Mediatek MT7621 SoC

In reply to [email protected]

From: Greg Ungerer <[email protected]>

The MediaTek MT7621 SoC device contains a 7530 switch, and the existing linux kernel 7530 DSA switch driver can be used with it.

The bulk of the changes required stem from the 7621 having different regulator and pad setup. The existing setup of these in the 7530 driver appears to be very specific to its implemtation in the Mediatek 7623 SoC. (Not entirely surprising given the 7623 is a quad core ARM based SoC, and the 7621 is a dual core, dual thread MIPS based SoC).

Create a new devicetree type, "mediatek,mt7621", to support the 7530 switch in the 7621 SoC. There appears to be no usable ID register to distinguish it from a 7530 in other hardware at runtime. This is used to carry out the appropriate configuration and setup.

---
 drivers/net/dsa/mt7530.c | 97 ++++++++++++++++++++++++----------------
 drivers/net/dsa/mt7530.h |  9 ++++
 2 files changed, 67 insertions(+), 39 deletions(-)

v1: initial patch
v2: changed to use separate devicetree binding

drivers/net/dsa/mt7530.c +58 -39
index 74547f43b938..c396665e576c 100644
@@ -622,17 +622,19 @@ static void mt7530_adjust_link(struct dsa_switch *ds, int port,
 	struct mt7530_priv *priv = ds->priv;
 
 	if (phy_is_pseudo_fixed_link(phydev)) {
-		dev_dbg(priv->dev, "phy-mode for master device = %x\n",
-			phydev->interface);
-
-		/* Setup TX circuit incluing relevant PAD and driving */
-		mt7530_pad_clk_setup(ds, phydev->interface);
-
-		/* Setup RX circuit, relevant PAD and driving on the host
-		 * which must be placed after the setup on the device side is
-		 * all finished.
-		 */
-		mt7623_pad_clk_setup(ds);
+		if (priv->id == ID_MT7530) {
+			dev_dbg(priv->dev, "phy-mode for master device = %x\n",
+				phydev->interface);
+
+			/* Setup TX circuit incluing relevant PAD and driving */
+			mt7530_pad_clk_setup(ds, phydev->interface);
+
+			/* Setup RX circuit, relevant PAD and driving on the
+			 * host which must be placed after the setup on the
+			 * device side is all finished.
+			 */
+			mt7623_pad_clk_setup(ds);
+		}
 	} else {
 		u16 lcl_adv = 0, rmt_adv = 0;
 		u8 flowctrl;
@@ -688,6 +690,10 @@ mt7530_cpu_port_enable(struct mt7530_priv *priv,
 	/* Unknown unicast frame fordwarding to the cpu port */
 	mt7530_set(priv, MT7530_MFC, UNU_FFP(BIT(port)));
 
+	/* Set CPU port number */
+	if (priv->id == ID_MT7621)
+		mt7530_rmw(priv, MT7530_MFC, CPU_MASK, CPU_EN | CPU_PORT(port));
+
 	/* CPU port gets connected to all user ports of
 	 * the switch
 	 */
@@ -1220,24 +1226,27 @@ mt7530_setup(struct dsa_switch *ds)
 	 * as two netdev instances.
 	 */
 	dn = ds->ports[MT7530_CPU_PORT].master->dev.of_node->parent;
-	priv->ethernet = syscon_node_to_regmap(dn);
-	if (IS_ERR(priv->ethernet))
-		return PTR_ERR(priv->ethernet);
 
-	regulator_set_voltage(priv->core_pwr, 1000000, 1000000);
-	ret = regulator_enable(priv->core_pwr);
-	if (ret < 0) {
-		dev_err(priv->dev,
-			"Failed to enable core power: %d\n", ret);
-		return ret;
-	}
+	if (priv->id == ID_MT7530) {
+		priv->ethernet = syscon_node_to_regmap(dn);
+		if (IS_ERR(priv->ethernet))
+			return PTR_ERR(priv->ethernet);
+
+		regulator_set_voltage(priv->core_pwr, 1000000, 1000000);
+		ret = regulator_enable(priv->core_pwr);
+		if (ret < 0) {
+			dev_err(priv->dev,
+				"Failed to enable core power: %d\n", ret);
+			return ret;
+		}
 
-	regulator_set_voltage(priv->io_pwr, 3300000, 3300000);
-	ret = regulator_enable(priv->io_pwr);
-	if (ret < 0) {
-		dev_err(priv->dev, "Failed to enable io pwr: %d\n",
-			ret);
-		return ret;
+		regulator_set_voltage(priv->io_pwr, 3300000, 3300000);
+		ret = regulator_enable(priv->io_pwr);
+		if (ret < 0) {
+			dev_err(priv->dev, "Failed to enable io pwr: %d\n",
+				ret);
+			return ret;
+		}
 	}
 
 	/* Reset whole chip through gpio pin or memory-mapped registers for
@@ -1327,9 +1336,17 @@ static const struct dsa_switch_ops mt7530_switch_ops = {
 	.port_vlan_del		= mt7530_port_vlan_del,
 };
 
+static const struct of_device_id mt7530_of_match[] = {
+	{ .compatible = "mediatek,mt7621", .data = (void *)ID_MT7621, },
+	{ .compatible = "mediatek,mt7530", .data = (void *)ID_MT7530, },
+	{ /* sentinel */ },
+};
+MODULE_DEVICE_TABLE(of, mt7530_of_match);
+
 static int
 mt7530_probe(struct mdio_device *mdiodev)
 {
+	const struct of_device_id *of_id;
 	struct mt7530_priv *priv;
 	struct device_node *dn;
 
@@ -1357,13 +1374,21 @@ mt7530_probe(struct mdio_device *mdiodev)
 		}
 	}
 
-	priv->core_pwr = devm_regulator_get(&mdiodev->dev, "core");
-	if (IS_ERR(priv->core_pwr))
-		return PTR_ERR(priv->core_pwr);
+	/* Get the hardware identifier from the devicetree node.
+	 * We will need it for some of the clock and regulator setup.
+	 */
+	of_id = of_match_node(mt7530_of_match, dn);
+	priv->id = (unsigned int)of_id->data;
 
-	priv->io_pwr = devm_regulator_get(&mdiodev->dev, "io");
-	if (IS_ERR(priv->io_pwr))
-		return PTR_ERR(priv->io_pwr);
+	if (priv->id == ID_MT7530) {
+		priv->core_pwr = devm_regulator_get(&mdiodev->dev, "core");
+		if (IS_ERR(priv->core_pwr))
+			return PTR_ERR(priv->core_pwr);
+
+		priv->io_pwr = devm_regulator_get(&mdiodev->dev, "io");
+		if (IS_ERR(priv->io_pwr))
+			return PTR_ERR(priv->io_pwr);
+	}
 
 	/* Not MCM that indicates switch works as the remote standalone
 	 * integrated circuit so the GPIO pin would be used to complete
@@ -1409,12 +1434,6 @@ mt7530_remove(struct mdio_device *mdiodev)
 	mutex_destroy(&priv->reg_mutex);
 }
 
-static const struct of_device_id mt7530_of_match[] = {
-	{ .compatible = "mediatek,mt7530" },
-	{ /* sentinel */ },
-};
-MODULE_DEVICE_TABLE(of, mt7530_of_match);
-
 static struct mdio_driver mt7530_mdio_driver = {
 	.probe  = mt7530_probe,
 	.remove = mt7530_remove,
drivers/net/dsa/mt7530.h +9 -0
index d9b407a22a58..a95ed958df5b 100644
@@ -19,6 +19,11 @@
 #define MT7530_NUM_FDB_RECORDS		2048
 #define MT7530_ALL_MEMBERS		0xff
 
+enum {
+	ID_MT7530 = 0,
+	ID_MT7621 = 1,
+};
+
 #define	NUM_TRGMII_CTRL			5
 
 #define TRGMII_BASE(x)			(0x10000 + (x))
@@ -36,6 +41,9 @@
 #define  UNM_FFP(x)			(((x) & 0xff) << 16)
 #define  UNU_FFP(x)			(((x) & 0xff) << 8)
 #define  UNU_FFP_MASK			UNU_FFP(~0)
+#define  CPU_EN				BIT(7)
+#define  CPU_PORT(x)			((x) << 4)
+#define  CPU_MASK			(0xf << 4)
 
 /* Registers for address table access */
 #define MT7530_ATA1			0x74
@@ -430,6 +438,7 @@ struct mt7530_priv {
 	struct regulator	*core_pwr;
 	struct regulator	*io_pwr;
 	struct gpio_desc	*reset;
+	unsigned int		id;
 	bool			mcm;
 
 	struct mt7530_port	ports[MT7530_NUM_PORTS];
Signature · 1 line
2.17.1
#6 lore raw

PATCH v2 4/4 dt-bindings: net: dsa: add new MT7530 binding to support MT7621

In reply to [email protected]

From: Greg Ungerer <[email protected]>

Add devicetree binding to support the compatible mt7530 switch as used in the MediaTek MT7621 SoC.

---
 Documentation/devicetree/bindings/net/dsa/mt7530.txt | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

v1: initial patch
v2: changed to use separate devicetree binding

Documentation/devicetree/bindings/net/dsa/mt7530.txt +2 -1
index aa3527f71fdc..b4e2af30776f 100644
@@ -3,7 +3,8 @@ Mediatek MT7530 Ethernet switch
 
 Required properties:
 
-- compatible: Must be compatible = "mediatek,mt7530";
+- compatible: may be compatible = "mediatek,mt7530"
+	or compatible = "mediatek,mt7621"
 - #address-cells: Must be 1.
 - #size-cells: Must be 0.
 - mediatek,mcm: Boolean; if defined, indicates that either MT7530 is the part
Signature · 1 line
2.17.1
maintainer
#7 lore raw

Re: [PATCHv2 4/4] dt-bindings: net: dsa: add new MT7530 binding to support MT7621

Quoted 4 lines · On Mon, Jan 14, 2019 at 05:03:34PM +1000, [email protected] wrote:

From: Greg Ungerer <[email protected]>

Add devicetree binding to support the compatible mt7530 switch as used in the MediaTek MT7621 SoC.

Hi Gerg

It gets messy, but could you try to indicate that core-supply and io-supply are not required for your new device. Currently the binding indicates they are required for all devices.

Thanks
Andrew

#8 lore raw

Re: [PATCHv2 4/4] dt-bindings: net: dsa: add new MT7530 binding to support MT7621

Hi Andrew,

Quoted 11 lines · Andrew Lunn
Quoted 4 lines · On Mon, Jan 14, 2019 at 05:03:34PM +1000, [email protected] wrote:

From: Greg Ungerer <[email protected]>

Add devicetree binding to support the compatible mt7530 switch as used in the MediaTek MT7621 SoC.

Hi Gerg

It gets messy, but could you try to indicate that core-supply and io-supply are not required for your new device. Currently the binding indicates they are required for all devices.

Yep, good point. Are you thinking something like this?

Documentation/devicetree/bindings/net/dsa/mt7530.txt +4 -1
@@ -3,16 +3,19 @@ Mediatek MT7530 Ethernet switch
 
 Required properties:
 
-- compatible: Must be compatible = "mediatek,mt7530";
+- compatible: may be compatible = "mediatek,mt7530"
+       or compatible = "mediatek,mt7621"
 - #address-cells: Must be 1.
 - #size-cells: Must be 0.
 - mediatek,mcm: Boolean; if defined, indicates that either MT7530 is the part
        on multi-chip module belong to MT7623A has or the remotely standalone
        chip as the function MT7623N reference board provided for.
 - core-supply: Phandle to the regulator node necessary for the core power.
+       (not required on mediatek,mt7621)
 - io-supply: Phandle to the regulator node necessary for the I/O power.
        See Documentation/devicetree/bindings/regulator/mt6323-regulator.txt
        for details for the regulator setup on these boards.
+       (not required on mediatek,mt7621)
 
 If the property mediatek,mcm isn't defined, following property is required
 

Regards
Greg

maintainer
#9 lore raw

Re: [PATCHv2 4/4] dt-bindings: net: dsa: add new MT7530 binding to support MT7621

Quoted 29 lines · Greg Ungerer

Hi Andrew,

Quoted 11 lines · Andrew Lunn
Quoted 4 lines · On Mon, Jan 14, 2019 at 05:03:34PM +1000, [email protected] wrote:

From: Greg Ungerer <[email protected]>

Add devicetree binding to support the compatible mt7530 switch as used in the MediaTek MT7621 SoC.

Hi Gerg

It gets messy, but could you try to indicate that core-supply and io-supply are not required for your new device. Currently the binding indicates they are required for all devices.

Yep, good point. Are you thinking something like this?

Documentation/devicetree/bindings/net/dsa/mt7530.txt +2 -1
@@ -3,16 +3,19 @@ Mediatek MT7530 Ethernet switch
 
 Required properties:
 
-- compatible: Must be compatible = "mediatek,mt7530";
+- compatible: may be compatible = "mediatek,mt7530"
+       or compatible = "mediatek,mt7621"
 - #address-cells: Must be 1.
 - #size-cells: Must be 0.
 - mediatek,mcm: Boolean; if defined, indicates that either MT7530 is the part

Documentation/devicetree/bindings/net/dsa/mt7530.txt Mediatek MT7530 Ethernet switch · line 20

Quoted 10 lines
Documentation/devicetree/bindings/net/dsa/mt7530.txt +2 -0
        on multi-chip module belong to MT7623A has or the remotely standalone
        chip as the function MT7623N reference board provided for.
 - core-supply: Phandle to the regulator node necessary for the core power.
+       (not required on mediatek,mt7621)
 - io-supply: Phandle to the regulator node necessary for the I/O power.
        See Documentation/devicetree/bindings/regulator/mt6323-regulator.txt
        for details for the regulator setup on these boards.
+       (not required on mediatek,mt7621)
 
 If the property mediatek,mcm isn't defined, following property is required

Hi Greg

As i said, it is a bit messy. I would probably have a section:

Required properties

which lists all common required properties. And then a section

Required properties mediatek,mt7530

With those which are required by that device.

Andrew

#10 lore raw

Re: [PATCHv2 4/4] dt-bindings: net: dsa: add new MT7530 binding to support MT7621

Hi Andrew,

On 15/1/19 11:18 pm, Andrew Lunn wrote:
[snip]

Quoted 9 lines

As i said, it is a bit messy. I would probably have a section:

Required properties

which lists all common required properties. And then a section

Required properties mediatek,mt7530

With those which are required by that device.

Ok, I see what you mean.
The simplest approach is something like this:

Documentation/devicetree/bindings/net/dsa/mt7530.txt +5 -1
index aa3527f71fdc..47aa205ee0bd 100644
@@ -3,12 +3,16 @@ Mediatek MT7530 Ethernet switch
 
 Required properties:
 
-- compatible: Must be compatible = "mediatek,mt7530";
+- compatible: may be compatible = "mediatek,mt7530"
+	or compatible = "mediatek,mt7621"
 - #address-cells: Must be 1.
 - #size-cells: Must be 0.
 - mediatek,mcm: Boolean; if defined, indicates that either MT7530 is the part
 	on multi-chip module belong to MT7623A has or the remotely standalone
 	chip as the function MT7623N reference board provided for.
+
+If compatible mediatek,mt7530 is set then the following properties are required
+
 - core-supply: Phandle to the regulator node necessary for the core power.
 - io-supply: Phandle to the regulator node necessary for the I/O power.
 	See Documentation/devicetree/bindings/regulator/mt6323-regulator.txt

That leaves the existing if/else with other bindings in place after this.

Maybe I am mis-reading the mt7530.c code but I am not entirely sure that "reset-gpios" is actually required for the mediatek,mcm not defined case - it is optional. (And I actually don't define it for my mt7621 case where mediatek,mcm is not defined).

Regards
Greg

maintainer
#11 lore raw

Re: [PATCHv2 4/4] dt-bindings: net: dsa: add new MT7530 binding to support MT7621

Quoted 28 lines · Greg Ungerer

Hi Andrew,

On 15/1/19 11:18 pm, Andrew Lunn wrote:
[snip]

Quoted 9 lines

As i said, it is a bit messy. I would probably have a section:

Required properties

which lists all common required properties. And then a section

Required properties mediatek,mt7530

With those which are required by that device.

Ok, I see what you mean.
The simplest approach is something like this:

Documentation/devicetree/bindings/net/dsa/mt7530.txt +2 -1
index aa3527f71fdc..47aa205ee0bd 100644
@@ -3,12 +3,16 @@ Mediatek MT7530 Ethernet switch
 Required properties:
-- compatible: Must be compatible = "mediatek,mt7530";
+- compatible: may be compatible = "mediatek,mt7530"
+	or compatible = "mediatek,mt7621"
 - #address-cells: Must be 1.

Documentation/devicetree/bindings/net/dsa/mt7530.txt Mediatek MT7530 Ethernet switch · line 16

Quoted 10 lines
Documentation/devicetree/bindings/net/dsa/mt7530.txt +3 -0
 - #size-cells: Must be 0.
 - mediatek,mcm: Boolean; if defined, indicates that either MT7530 is the part
 	on multi-chip module belong to MT7623A has or the remotely standalone
 	chip as the function MT7623N reference board provided for.
+
+If compatible mediatek,mt7530 is set then the following properties are required
+
 - core-supply: Phandle to the regulator node necessary for the core power.
 - io-supply: Phandle to the regulator node necessary for the I/O power.
 	See Documentation/devicetree/bindings/regulator/mt6323-regulator.txt

Yes, that looks good.

Quoted 8 lines

That leaves the existing if/else with other bindings in place after this.

Maybe I am mis-reading the mt7530.c code but I am not entirely sure that "reset-gpios" is actually required for the mediatek,mcm not defined case - it is optional. (And I actually don't define it for my mt7621 case where mediatek,mcm is not defined).

The gpio seems to be optional in general, any only used for device other than mediatek,mcm.

The reset controller is required for mediatek,mcm, but not others.

So it looks like the binding document needs a few fixes :-(

Andrew

#12 lore raw

Re: [PATCHv2 4/4] dt-bindings: net: dsa: add new MT7530 binding to support MT7621

Hi Andrew,

Quoted 51 lines · Andrew Lunn
Quoted 28 lines · Greg Ungerer

Hi Andrew,

On 15/1/19 11:18 pm, Andrew Lunn wrote:
[snip]

Quoted 9 lines

As i said, it is a bit messy. I would probably have a section:

Required properties

which lists all common required properties. And then a section

Required properties mediatek,mt7530

With those which are required by that device.

Ok, I see what you mean.
The simplest approach is something like this:

Documentation/devicetree/bindings/net/dsa/mt7530.txt +2 -1
index aa3527f71fdc..47aa205ee0bd 100644
@@ -3,12 +3,16 @@ Mediatek MT7530 Ethernet switch
  Required properties:
-- compatible: Must be compatible = "mediatek,mt7530";
+- compatible: may be compatible = "mediatek,mt7530"
+	or compatible = "mediatek,mt7621"
  - #address-cells: Must be 1.

Documentation/devicetree/bindings/net/dsa/mt7530.txt Mediatek MT7530 Ethernet switch · line 16

Quoted 10 lines
Documentation/devicetree/bindings/net/dsa/mt7530.txt +3 -0
  - #size-cells: Must be 0.
  - mediatek,mcm: Boolean; if defined, indicates that either MT7530 is the part
  	on multi-chip module belong to MT7623A has or the remotely standalone
  	chip as the function MT7623N reference board provided for.
+
+If compatible mediatek,mt7530 is set then the following properties are required
+
  - core-supply: Phandle to the regulator node necessary for the core power.
  - io-supply: Phandle to the regulator node necessary for the I/O power.
  	See Documentation/devicetree/bindings/regulator/mt6323-regulator.txt

Yes, that looks good.

Quoted 8 lines

That leaves the existing if/else with other bindings in place after this.

Maybe I am mis-reading the mt7530.c code but I am not entirely sure that "reset-gpios" is actually required for the mediatek,mcm not defined case - it is optional. (And I actually don't define it for my mt7621 case where mediatek,mcm is not defined).

Quoted 6 lines

The gpio seems to be optional in general, any only used for device other than mediatek,mcm.

The reset controller is required for mediatek,mcm, but not others.

So it looks like the binding document needs a few fixes :-(

Yep.. Thanks for the feedback though. I'll roll a v3.

Regards
Greg