Skip to contentSkip to conversation

wrt: dma_intr: status=0x51 { DriveReady SeekComplete Error }

DISCUSSION Peter 3 participants 6 messages Aug 26, 2006 – Aug 27, 2006

lore
Share & tools
lore

Peter

author
#0 lore raw

Using 2.6.17.11 with reiser4 patch only. Voluntary preempt.

Recently, I have been receiving this sequence of errors:

hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
ide: failed opcode was: unknown
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
ide: failed opcode was: unknown
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
ide: failed opcode was: unknown
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
ide: failed opcode was: unknown
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
ide: failed opcode was: unknown
hdb: DMA disabled

Previously, with a different hdb drive, the above hda/b were reversed, but the output the same.

Diagnostics on the drives are fine. Removing the b drive removes the messages. System functions fine anyway, and no data is lost as a result of the errors. The persistence of it is frustrating!

With so many moving parts in a kernel, applications, drivers, and a user's system, it's hard to pin down the root of the problem. I have a mix of filesystems, drivers, etc. While I cannot recall exactly when I started noticing these problems, I would venture it was in the 2.6.16 series. I have two thoughts about these errors.

1) In my case, hda and hdb are different in capabilities. /dev/hda:

Model=Maxtor 6Y200P0, FwRev=YAR41BW0, SerialNo=Y65WFMPE
Config={ Fixed }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=57
BuffType=DualPortCache, BuffSize=7936kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=268435455
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 udma4 udma5 *udma6
AdvancedPM=yes: disabled (255) WriteCache=enabled
Drive conforms to: (null): ATA/ATAPI-1 ATA/ATAPI-2 ATA/ATAPI-3 ATA/ATAPI-4 ATA/ATAPI-5 ATA/ATAPI-6 ATA/ATAPI-7

/dev/hdb:

Model=Maxtor 5T030H3, FwRev=TAH71DP0, SerialNo=T3H1876C
Config={ Fixed }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=57
BuffType=DualPortCache, BuffSize=2048kB, MaxMultSect=16, MultSect=16
(maybe): CurCHS=65535/16/0, CurSects=0, LBA=yes, LBAsects=60030432
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=yes: disabled (255) WriteCache=enabled
Drive conforms to: ATA/ATAPI-6 T13 1410D revision 0: ATA/ATAPI-1 ATA/ATAPI-2 ATA/ATAPI-3 ATA/ATAPI-4 ATA/ATAPI-5 ATA/ATAPI-6

could it be that the dma or io handler is having trouble when each device has different capabilities on the same ide channel? Or, could it be that reiserfs or reiser4 is turning off dma because it is timing out somehow?

2) VMWare. I have noticed recently that the errors are occurring during or after VMWare is run.

from dmesg:

/dev/vmnet: open called by PID 9443 (vmware-vmx)
eth0: Promiscuous mode enabled.
device eth0 entered promiscuous mode
bridge-eth0: enabled promiscuous mode
/dev/vmnet: port on hub 0 successfully opened
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
ide: failed opcode was: unknown

I have tried compiling with all three preemption models, including with the ck, beyond, and other variant patchsets. Currently, I am testing with NO preemption and the errors are fewer but still there.

MOBO bios has dma enabled including for UDMA and prefetch is set to on. Again, it's interesting to note I did not observe this error with only one drive on ide0. I cannot pin down any more details at the moment, but if anyone wants to explore this further (I know this has been an issue for years), I am happy to try and help.

Signature · 6 lines
Peter
+++++
Do not reply to this email, it is a spam trap and not monitored.
I can be reached via this list, or via 
jabber: pete4abw at jabber.org
ICQ: 73676357
author
#1 lore raw
Quoted 7 lines · Peter

Using 2.6.17.11 with reiser4 patch only. Voluntary preempt.

Recently, I have been receiving this sequence of errors:

hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
ide: failed opcode was: unknown

snip....

I should mention that I have an 80 pin IDE cables, and did try replacing it. Same result. This problem is new, so I do not believe the cable is the issue -- esp since manu diags show all is well.

Signature · 6 lines
Peter
+++++
Do not reply to this email, it is a spam trap and not monitored.
I can be reached via this list, or via 
jabber: pete4abw at jabber.org
ICQ: 73676357
#2 lore raw
In reply to Peter

Ar Sad, 2006-08-26 am 16:12 +0000, ysgrifennodd Peter:

Quoted 2 lines

2) VMWare. I have noticed recently that the errors are occurring during or after VMWare is run.

Then please report them to the vmware people unless you can reproduce it from a clean boot which never touched vmware or loaded any vmware modules.

The only real way this error can occur other than hardware is if something crapped on the drive configuration. If it is triggered by vmware you know who to talk to 8)

#3 lore raw
In reply to Peter
Quoted 3 lines · Peter

Diagnostics on the drives are fine. Removing the b drive removes the messages. System functions fine anyway, and no data is lost as a result of the errors. The persistence of it is frustrating!

What diagnostics did you try?

(I've got experience with a guy saying: "I have 5 which test perfect with my diagnostics, but my embedded machine refuses them. What's wrong?" All of them report through SMART that they HAVE reported media errors, and they all have bad blocks.)

Do you have "smartd" running? I vaguely remember that it sometimes triggered error messages from the normal driver.

Roger.

Signature · 5 lines
** [email protected] ** http://www.BitWizard.nl/ ** +31-15-2600998 **
*-- BitWizard writes Linux device drivers for any device you may have! --*
Q: It doesn't work. A: Look buddy, doesn't work is an ambiguous statement. 
Does it sit on the couch all day? Is it unemployed? Please be specific! 
Define 'it' and what it isn't doing. --------- Adapted from lxrbot FAQ
author
#4 lore raw
Quoted 7 lines · Rogier Wolff
Quoted 3 lines · Peter

Diagnostics on the drives are fine. Removing the b drive removes the messages. System functions fine anyway, and no data is lost as a result of the errors. The persistence of it is frustrating!

What diagnostics did you try?

First badblocks, then Manufacturer's (Maxtor) overnight burn in tests.

Quoted 4 lines

(I've got experience with a guy saying: "I have 5 which test perfect with my diagnostics, but my embedded machine refuses them. What's wrong?" All of them report through SMART that they HAVE reported media errors, and they all have bad blocks.)

I tried to be more careful before posting here :). I even ran a second test on the drives on a second machine.

Quoted 4 lines

Do you have "smartd" running? I vaguely remember that it sometimes triggered error messages from the normal driver.

No, but I think there is a driver issue such as VMW or the reiserfs. Reiser even mentions this error on his faq suggesting it's a bad ide cable. Of course, I changed mine (now testing #4). Of course, switching to NO preempt has reduced the volume of errors greatly. Even last night there were none for the time being.

thx.

Signature · 6 lines
Peter
+++++
Do not reply to this email, it is a spam trap and not monitored.
I can be reached via this list, or via 
jabber: pete4abw at jabber.org
ICQ: 73676357
author
#5 lore raw

RESOLVED: dma_intr: status=0x51 { DriveReady SeekComplete Error }

In reply to Peter

I am guessing that a recent update with kernel patches for iosched-rollup-2.6.17.4-2.patch appears to have removed the problems described here. With this and others installed, even with CONFIG_PREEMPT=y there are no more io problems being recorded with or without vmware mods. For some reason, these patches are not in the vanilla 2.6.17.11 sources.

The particular kernel series I used for test were:

2.6.17.11 - problem persisted
2.6.17-beyond3.1pre1 - problem persisted 2.6.17-beyond4pre1 - problem solved ( for half a day anyway :) )

http://iphitus.loudas.com/beyond/2.6.17/2.6.17-beyond4pre1/

compare dmesg output at point of error:

Failure:
/dev/vmnet: open called by PID 9443 (vmware-vmx)
eth0: Promiscuous mode enabled.
device eth0 entered promiscuous mode
bridge-eth0: enabled promiscuous mode
/dev/vmnet: port on hub 0 successfully opened
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
ide: failed opcode was: unknown

NOW:
/dev/vmnet: open called by PID 11758 (vmware-vmx)
eth0: Promiscuous mode enabled.
device eth0 entered promiscuous mode
bridge-eth0: enabled promiscuous mode
/dev/vmnet: port on hub 0 successfully opened
( *** note, error occured here *** ) /dev/vmmon[11758]: host clock rate change request 83 -> 19 device eth0 left promiscuous mode
bridge-eth0: disabled promiscuous mode /dev/vmmon[11752]: host clock rate change request 19 -> 0

This sequence occured several places, and no times were errors reported.

HTH

So, for me, for now, this issue is resolved...

Signature · 6 lines
Peter
+++++
Do not reply to this email, it is a spam trap and not monitored.
I can be reached via this list, or via 
jabber: pete4abw at jabber.org
ICQ: 73676357