powerpc/pseries/iommu: Add TCEs for 16GB pages when RAM is pre-mapped
PATCH v2 1/1 powerpc/pseries/iommu: Add TCEs for 16GB pages when RAM is pre-mapped
In powerPC, if Dynamic DMA Window is big enough, RAM is pre-mapped. To determine the size of RAM, a PAPR+ property "ibm,lrdr-capacity" is used. This OF property dictates what is the max size of RAM an LPAR can have, including DR added memory.
In PowerPC, 16GB pages can be allocated at machine level and then assigned to LPARs. These 16GB pages are added to LPAR memory at the time of boot. The address range for these 16GB pages is above MAX RAM an LPAR can have (ibm,lrdr-capacity). In the current implementation, these 16GB pages are being excluded from pre-mapped TCEs. A driver can have DMA buffers allocated from 16GB pages. This results in platform to raise an EEH when DMA is attempted on buffers in 16GB memory range.
commit 6aa989ab2bd0 ("powerpc/pseries/iommu: memory notifier incorrectly adds TCEs for pmemory")
Prior to the above patch, memblock_end_of_DRAM() was being used to determine the MAX memory of an LPAR. This included 16GB pages as well. The issue with using memblock_end_of_DRAM() is that when pmemory is converted to RAM via daxctl command, the DDW engine will incorrectly try to add TCEs for pmemory as well.
Below is the address distribution of RAM, 16GB pages and pmemory for an LPAR with max memory of 256GB, memory allocated 64GB, 2 16GB pages and assigned pmemory of 8GB.
RANGE SIZE STATE REMOVABLE BLOCK
0x0000000000000000-0x0000000fffffffff 64G online yes 0-255 0x0000004000000000-0x00000047ffffffff 32G online yes 1024-1151
cat /sys/bus/nd/devices/region0/resource0x40100000000
cat /sys/bus/nd/devices/region0/size
8589934592
The approach to fix this problem is to revert back the code changes introduced by the above patch and to stash away the MAX memory of an LPAR, including 16GB pages, at the LPAR boot time. This value is then used whenever TCEs are needed to be pre-mapped - enable_DDW() or, iommu_mem_notifier()
---
Change log:
V1 -> V2
1. Harsh: Not only start_pfn, but end_pfn also needs to be within allowed range, which may require clamping arg->nr_pages if crossing the limits.
Response: Incorporated changes.
arch/powerpc/platforms/pseries/iommu.c | 56 ++++++++++++++++++-------- 1 file changed, 40 insertions(+), 16 deletions(-)
arch/powerpc/platforms/pseries/iommu.c +40 -16
@@ -69,6 +69,8 @@ static struct iommu_table *iommu_pseries_alloc_table(int node)return tbl; } +static phys_addr_t pseries_ddw_max_ram; +#ifdef CONFIG_IOMMU_API static struct iommu_table_group_ops spapr_tce_table_group_ops;#endif
@@ -1285,15 +1287,19 @@ static LIST_HEAD(failed_ddw_pdn_list);static phys_addr_t ddw_memory_hotplug_max (void ) { -resource_size_t max_addr; +resource_size_t max_addr =memory_hotplug_max (); +struct device_node *memory; -#if defined(CONFIG_NUMA ) && defined(CONFIG_MEMORY_HOTPLUG ) - max_addr =hot_add_drconf_memory_max (); -#else - max_addr =memblock_end_of_DRAM (); -#endif +for_each_node_by_type (memory,"memory" ) { +struct resource res; + +if (of_address_to_resource (memory,0 , &res)) +continue ; + + max_addr =max_t (resource_size_t, max_addr, res.end +1 ); + } -return max_addr; +return max_addr; }/*
@@ -1446,7 +1452,7 @@ static struct property *ddw_property_create(const char *propname, u32 liobn, u64static bool enable_ddw (struct pci_dev *dev,struct device_node *pdn,u64 dma_mask) {int len =0 , ret; -int max_ram_len =order_base_2 (ddw_memory_hotplug_max ()); +int max_ram_len =order_base_2 (pseries_ddw_max_ram);struct ddw_query_response query;struct ddw_create_response create;int page_shift;
@@ -1668,7 +1674,7 @@ static bool enable_ddw(struct pci_dev *dev, struct device_node *pdn, u64 dma_masif (direct_mapping) {/* DDW maps the whole partition, so enable direct DMA mapping */ - ret =walk_system_ram_range (0 ,ddw_memory_hotplug_max () >>PAGE_SHIFT , + ret =walk_system_ram_range (0 , pseries_ddw_max_ram >>PAGE_SHIFT , win64->value, tce_setrange_multi_pSeriesLP_walk);if (ret) { dev_info(&dev->dev, "failed to map DMA window for %pOF: %d\n",
@@ -2419,21 +2425,32 @@ static int iommu_mem_notifier(struct notifier_block *nb, unsigned long action, {struct dma_win *window;struct memory_notify *arg = data; +unsigned long limit = arg->nr_pages; +unsigned long max_ram_pages = pseries_ddw_max_ram >>PAGE_SHIFT ;int ret =0 ;/* This notifier can get called when onlining persistent memory as well. * TCEs are not pre-mapped for persistent memory. Persistent memory will -* always be above ddw_memory_hotplug_max() +* always be above pseries_ddw_max_ram */ +if (arg->start_pfn >= max_ram_pages) +return NOTIFY_OK ; + +/* RAM is being DLPAR'ed. The range should never exceed max ram. +* Just in case, clamp the range and throw a warning. +*/ +if (arg->start_pfn + limit > max_ram_pages) { + limit = max_ram_pages - arg->start_pfn; +WARN_ON (1 ); + }switch (action) {case MEM_GOING_ONLINE :spin_lock (&dma_win_list_lock);list_for_each_entry (window, &dma_win_list, list) { -if (window->direct && (arg->start_pfn <<PAGE_SHIFT ) < -ddw_memory_hotplug_max ()) { +if (window->direct) { ret |=tce_setrange_multi_pSeriesLP (arg->start_pfn, - arg->nr_pages, window->prop); + limit, window->prop); }/* XXX log error */ }
@@ -2443,10 +2460,9 @@ static int iommu_mem_notifier(struct notifier_block *nb, unsigned long action,case MEM_OFFLINE :spin_lock (&dma_win_list_lock);list_for_each_entry (window, &dma_win_list, list) { -if (window->direct && (arg->start_pfn <<PAGE_SHIFT ) < -ddw_memory_hotplug_max ()) { +if (window->direct) { ret |=tce_clearrange_multi_pSeriesLP (arg->start_pfn, - arg->nr_pages, window->prop); + limit, window->prop); }/* XXX log error */ }
@@ -2532,6 +2548,14 @@ void __init iommu_init_early_pSeries(void)register_memory_notifier (&iommu_mem_nb);set_pci_dma_ops (&dma_iommu_ops); + +/* During init determine the max memory an LPAR can have and set it. This +* will be used for pre-mapping RAM in DDW. memblock_end_of_DRAM() can +* change during the running of LPAR - daxctl can add pmemory as +* "system-ram". This memory range should not be pre-mapped in DDW since +* the address of pmemory can be much higher than the DDW size. +*/ + pseries_ddw_max_ram =ddw_memory_hotplug_max (); }static int __init disable_multitce (char *str)
base-commit: 6d35786de28116ecf78797a62b84e6bf3c45aa5a
Signature · 1 line
2.39.3
Quoted 47 lines · Gaurav Batra
In powerPC, if Dynamic DMA Window is big enough, RAM is pre-mapped. To determine the size of RAM, a PAPR+ property "ibm,lrdr-capacity" is used. This OF property dictates what is the max size of RAM an LPAR can have, including DR added memory.
In PowerPC, 16GB pages can be allocated at machine level and then assigned to LPARs. These 16GB pages are added to LPAR memory at the time of boot. The address range for these 16GB pages is above MAX RAM an LPAR can have (ibm,lrdr-capacity). In the current implementation, these 16GB pages are being excluded from pre-mapped TCEs. A driver can have DMA buffers allocated from 16GB pages. This results in platform to raise an EEH when DMA is attempted on buffers in 16GB memory range.
commit
6aa989ab2bd0("powerpc/pseries/iommu: memory notifier incorrectly adds TCEs for pmemory")Prior to the above patch,
memblock_end_of_DRAM()was being used to determine the MAX memory of an LPAR. This included 16GB pages as well. The issue with usingmemblock_end_of_DRAM()is that when pmemory is converted to RAM via daxctl command, the DDW engine will incorrectly try to add TCEs for pmemory as well.Below is the address distribution of RAM, 16GB pages and pmemory for an LPAR with max memory of 256GB, memory allocated 64GB, 2 16GB pages and assigned pmemory of 8GB.
RANGE SIZE STATE REMOVABLE BLOCK
0x0000000000000000-0x0000000fffffffff 64G online yes 0-255 0x0000004000000000-0x00000047ffffffff 32G online yes 1024-1151cat
/sys/bus/nd/devices/region0/resource0x40100000000
cat/sys/bus/nd/devices/region0/size
8589934592The approach to fix this problem is to revert back the code changes introduced by the above patch and to stash away the MAX memory of an LPAR, including 16GB pages, at the LPAR boot time. This value is then used whenever TCEs are needed to be pre-mapped -
enable_DDW()or,iommu_mem_notifier()Fixes 6aa989ab2bd0 ("powerpc/pseries/iommu: memory notifier incorrectly adds TCEs for pmemory")Signed-off-by Gaurav Batra <[email protected]>---
Change log:
Quoted 8 lines
V1 -> V2
1. Harsh: Not only
start_pfn, butend_pfnalso needs to be within allowed range, which may require clampingarg->nr_pagesif crossing the limits.Response: Incorporated changes.
Reviewed-by Harsh Prateek Bora <[email protected]>
I think I mentioned it before also. Please avoid using tags unless explicitly provided by the reviewer.
Quoted 28 lines
arch/powerpc/platforms/pseries/iommu.c | 56 ++++++++++++++++++-------- 1 file changed, 40 insertions(+), 16 deletions(-)arch/powerpc/platforms/pseries/iommu.c +4
-4@@ -69,6 +69,8 @@ static struct iommu_table *iommu_pseries_alloc_table(int node)return tbl; } +static phys_addr_t pseries_ddw_max_ram; +#ifdef CONFIG_IOMMU_API static struct iommu_table_group_ops spapr_tce_table_group_ops;#endif @@ -1285,15 +1287,19 @@ static LIST_HEAD(failed_ddw_pdn_list);static phys_addr_t ddw_memory_hotplug_max (void ) { -resource_size_t max_addr; +resource_size_t max_addr =memory_hotplug_max (); +struct device_node *memory; -#if defined(CONFIG_NUMA ) && defined(CONFIG_MEMORY_HOTPLUG ) - max_addr =hot_add_drconf_memory_max (); -#else
arch/powerpc/platforms/pseries/iommu.c static LIST_HEAD(failed_ddw_pdn_list); · line 1300
Quoted 10 lines
arch/powerpc/platforms/pseries/iommu.c +8
-2- max_addr =memblock_end_of_DRAM (); -#endif +for_each_node_by_type (memory,"memory" ) { +struct resource res; + +if (of_address_to_resource (memory,0 , &res)) +continue ; + + max_addr =max_t (resource_size_t, max_addr, res.end +1 ); + }
Indentation needs to be corrected above and below.
Quoted 36 lines
arch/powerpc/platforms/pseries/iommu.c +6
-4-return max_addr; +return max_addr; }/* @@ -1446,7 +1452,7 @@ static struct property *ddw_property_create(const char *propname, u32 liobn, u64static bool enable_ddw (struct pci_dev *dev,struct device_node *pdn,u64 dma_mask) {int len =0 , ret; -int max_ram_len =order_base_2 (ddw_memory_hotplug_max ()); +int max_ram_len =order_base_2 (pseries_ddw_max_ram);struct ddw_query_response query;struct ddw_create_response create;int page_shift;@@ -1668,7 +1674,7 @@ static bool enable_ddw(struct pci_dev *dev, struct device_node *pdn, u64 dma_masif (direct_mapping) {/* DDW maps the whole partition, so enable direct DMA mapping */ - ret =walk_system_ram_range (0 ,ddw_memory_hotplug_max () >>PAGE_SHIFT , + ret =walk_system_ram_range (0 , pseries_ddw_max_ram >>PAGE_SHIFT , win64->value, tce_setrange_multi_pSeriesLP_walk);if (ret) { dev_info(&dev->dev, "failed to map DMA window for %pOF: %d\n",@@ -2419,21 +2425,32 @@ static int iommu_mem_notifier(struct notifier_block *nb, unsigned long action, {struct dma_win *window;struct memory_notify *arg = data; +unsigned long limit = arg->nr_pages; +unsigned long max_ram_pages = pseries_ddw_max_ram >>PAGE_SHIFT ;int ret =0 ;/* This notifier can get called when onlining persistent memory as well. * TCEs are not pre-mapped for persistent memory. Persistent memory will -* always be above ddw_memory_hotplug_max() +* always be above pseries_ddw_max_ram
arch/powerpc/platforms/pseries/iommu.c static int iommu_mem_notifier(struct notifier_block *nb, unsigned long action, · line 2444
Quoted 10 lines
arch/powerpc/platforms/pseries/iommu.c +9
-0*/ +if (arg->start_pfn >= max_ram_pages) +return NOTIFY_OK ; + +/* RAM is being DLPAR'ed. The range should never exceed max ram. +* Just in case, clamp the range and throw a warning. +*/ +if (arg->start_pfn + limit > max_ram_pages) { + limit = max_ram_pages - arg->start_pfn; +WARN_ON (1 );
WARN_ONCE with an appropriate warning message may be a better choice.
Quoted 4 lines
arch/powerpc/platforms/pseries/iommu.c +1
-0+ }switch (action) {case MEM_GOING_ONLINE :
arch/powerpc/platforms/pseries/iommu.c static int iommu_mem_notifier(struct notifier_block *nb, unsigned long action, · line 2455
Quoted 10 lines
arch/powerpc/platforms/pseries/iommu.c +2
-3spin_lock (&dma_win_list_lock);list_for_each_entry (window, &dma_win_list, list) { -if (window->direct && (arg->start_pfn <<PAGE_SHIFT ) < -ddw_memory_hotplug_max ()) { +if (window->direct) { ret |=tce_setrange_multi_pSeriesLP (arg->start_pfn, - arg->nr_pages, window->prop); + limit, window->prop); }/* XXX log error */
Replace comment with a log if limit < arg->nr_pages ? Similarly below as well.
arch/powerpc/platforms/pseries/iommu.c static int iommu_mem_notifier(struct notifier_block *nb, unsigned long action, · line 2467
Quoted 13 lines
arch/powerpc/platforms/pseries/iommu.c +2
-3}@@ -2443,10 +2460,9 @@ static int iommu_mem_notifier(struct notifier_block *nb, unsigned long action,case MEM_OFFLINE :spin_lock (&dma_win_list_lock);list_for_each_entry (window, &dma_win_list, list) { -if (window->direct && (arg->start_pfn <<PAGE_SHIFT ) < -ddw_memory_hotplug_max ()) { +if (window->direct) { ret |=tce_clearrange_multi_pSeriesLP (arg->start_pfn, - arg->nr_pages, window->prop); + limit, window->prop); }/* XXX log error */
^^^ Ditto.
Thanks
Harsh
Quoted 18 lines
arch/powerpc/platforms/pseries/iommu.c +8
-0}@@ -2532,6 +2548,14 @@ void __init iommu_init_early_pSeries(void)register_memory_notifier (&iommu_mem_nb);set_pci_dma_ops (&dma_iommu_ops); + +/* During init determine the max memory an LPAR can have and set it. This +* will be used for pre-mapping RAM in DDW. memblock_end_of_DRAM() can +* change during the running of LPAR - daxctl can add pmemory as +* "system-ram". This memory range should not be pre-mapped in DDW since +* the address of pmemory can be much higher than the DDW size. +*/ + pseries_ddw_max_ram =ddw_memory_hotplug_max (); }static int __init disable_multitce (char *str)base-commit:
6d35786de28116ecf78797a62b84e6bf3c45aa5a
Quoted 52 lines · Harsh Prateek Bora
Quoted 49 lines · Gaurav Batra
In powerPC, if Dynamic DMA Window is big enough, RAM is pre-mapped. To determine the size of RAM, a PAPR+ property "ibm,lrdr-capacity" is used. This OF property dictates what is the max size of RAM an LPAR can have, including DR added memory.
In PowerPC, 16GB pages can be allocated at machine level and then assigned to LPARs. These 16GB pages are added to LPAR memory at the time of boot. The address range for these 16GB pages is above MAX RAM an LPAR can have (ibm,lrdr-capacity). In the current implementation, these 16GB pages are being excluded from pre-mapped TCEs. A driver can have DMA buffers allocated from 16GB pages. This results in platform to raise an EEH when DMA is attempted on buffers in 16GB memory range.
commit
6aa989ab2bd0("powerpc/pseries/iommu: memory notifier incorrectly adds TCEs for pmemory")Prior to the above patch,
memblock_end_of_DRAM()was being used to determine the MAX memory of an LPAR. This included 16GB pages as well. The issue with usingmemblock_end_of_DRAM()is that when pmemory is converted to RAM via daxctl command, the DDW engine will incorrectly try to add TCEs for pmemory as well.Below is the address distribution of RAM, 16GB pages and pmemory for an LPAR with max memory of 256GB, memory allocated 64GB, 2 16GB pages and assigned pmemory of 8GB.
RANGE SIZE STATE REMOVABLE BLOCK 0x0000000000000000-0x0000000fffffffff 64G online yes 0-255 0x0000004000000000-0x00000047ffffffff 32G online yes 1024-1151
cat
/sys/bus/nd/devices/region0/resource0x40100000000
cat/sys/bus/nd/devices/region0/size
8589934592The approach to fix this problem is to revert back the code changes introduced by the above patch and to stash away the MAX memory of an LPAR, including 16GB pages, at the LPAR boot time. This value is then used whenever TCEs are needed to be pre-mapped -
enable_DDW()or,iommu_mem_notifier()Fixes 6aa989ab2bd0 ("powerpc/pseries/iommu: memory notifier incorrectly adds TCEs for pmemory")Signed-off-by Gaurav Batra <[email protected]>---
Change log:
V1 -> V2
Quoted 8 lines
Quoted 6 lines
1. Harsh: Not only
start_pfn, butend_pfnalso needs to be within allowed range, which may require clampingarg->nr_pagesif crossing the limits.Response: Incorporated changes.
Reviewed-by Harsh Prateek Bora <[email protected]>I think I mentioned it before also. Please avoid using tags unless explicitly provided by the reviewer.
my apologies, I thought you meant to move it to "review comments section". I will remove them in my next version of the patch
Quoted 147 lines
Quoted 27 lines
arch/powerpc/platforms/pseries/iommu.c| 56 ++++++++++++++++++--------1 file changed, 40 insertions(+), 16 deletions(-)arch/powerpc/platforms/pseries/iommu.c +1
-0@@ -69,6 +69,8 @@ static struct iommu_table *iommu_pseries_alloc_table(int node) return tbl; } +static phys_addr_t pseries_ddw_max_ram; + #ifdef CONFIG_IOMMU_API static struct iommu_table_group_ops spapr_tce_table_group_ops;#endif
arch/powerpc/platforms/pseries/iommu.c +2
-3@@ -1285,15 +1287,19 @@ static LIST_HEAD(failed_ddw_pdn_list); static phys_addr_t ddw_memory_hotplug_max(void) { - resource_size_t max_addr; + resource_size_t max_addr = memory_hotplug_max(); + struct device_node *memory; -#if defined(CONFIG_NUMA) && defined(CONFIG_MEMORY_HOTPLUG) - max_addr = hot_add_drconf_memory_max(); -#else arch/powerpc/platforms/pseries/iommu.c static LIST_HEAD(failed_ddw_pdn_list); · line 1299
Quoted 10 lines
arch/powerpc/platforms/pseries/iommu.c +8
-2- max_addr = memblock_end_of_DRAM(); -#endif + for_each_node_by_type(memory, "memory") { + struct resource res; + + if (of_address_to_resource(memory, 0, &res)) + continue; + + max_addr = max_t(resource_size_t, max_addr, res.end + 1); + }Indentation needs to be corrected above and below.
Quoted 37 lines
arch/powerpc/platforms/pseries/iommu.c +2
-1- return max_addr; + return max_addr; } /*@@ -1446,7 +1452,7 @@ static struct property *ddw_property_create(const char *propname, u32 liobn, u64 static bool enable_ddw(struct pci_dev *dev, struct device_node *pdn, u64 dma_mask) { int len = 0, ret; - int max_ram_len = order_base_2(ddw_memory_hotplug_max()); + int max_ram_len = order_base_2(pseries_ddw_max_ram); struct ddw_query_response query; struct ddw_create_response create;int
page_shift;arch/powerpc/platforms/pseries/iommu.c +0
-0@@ -1668,7 +1674,7 @@ static bool enable_ddw(struct pci_dev *dev,struct
device_node*pdn, u64dma_mas
if (direct_mapping) {
/* DDW maps the whole partition, so enable direct DMA mapping */ - ret = walk_system_ram_range(0,ddw_memory_hotplug_max()>>PAGE_SHIFT,
+ ret = walk_system_ram_range(0,pseries_ddw_max_ram>>PAGE_SHIFT,
win64->value,tce_setrange_multi_pSeriesLP_walk); if (ret) {
dev_info(&dev->dev, "failed to map DMA window for %pOF: %d\n",arch/powerpc/platforms/pseries/iommu.c +3
-1@@ -2419,21 +2425,32 @@ static int iommu_mem_notifier(struct notifier_block *nb, unsigned long action, { struct dma_win *window; struct memory_notify *arg = data; + unsigned long limit = arg->nr_pages; + unsigned long max_ram_pages = pseries_ddw_max_ram >> PAGE_SHIFT; int ret = 0; /* This notifier can get called when onlining persistent memory as well.* TCEs are not pre-mapped for persistent memory. Persistent memory will -* always be above ddw_memory_hotplug_max() +* always be above pseries_ddw_max_ram arch/powerpc/platforms/pseries/iommu.c static int iommu_mem_notifier(struct · line 2444
Quoted 10 lines
arch/powerpc/platforms/pseries/iommu.c +9
-0*/ + if (arg->start_pfn >= max_ram_pages) + return NOTIFY_OK; + + /* RAM is being DLPAR'ed. The range should never exceed max ram. + * Just in case, clamp the range and throw a warning. + */ + if (arg->start_pfn + limit > max_ram_pages) { + limit = max_ram_pages - arg->start_pfn; + WARN_ON(1);
WARN_ONCEwith an appropriate warning message may be a better choice.Quoted 5 lines
arch/powerpc/platforms/pseries/iommu.c +1
-0+ } switch (action) {case
MEM_GOING_ONLINE:
spin_lock(&dma_win_list_lock);list_for_each_entry(window, &dma_win_list, list){Quoted 8 lines
- if (
window->direct&& (arg->start_pfn<<PAGE_SHIFT) < -ddw_memory_hotplug_max()) {
+ if (window->direct) {
ret |=tce_setrange_multi_pSeriesLP(arg->start_pfn, - arg->nr_pages, window->prop);
+ limit,window->prop);
}
/* XXX log error */Replace comment with a log if limit <
arg->nr_pages? Similarly below as well.Quoted 6 lines
}
arch/powerpc/platforms/pseries/iommu.c +0
-0@@ -2443,10 +2460,9 @@ static int iommu_mem_notifier(struct notifier_block *nb, unsigned long action,case
MEM_OFFLINE:
spin_lock(&dma_win_list_lock);list_for_each_entry(window, &dma_win_list, list){Quoted 8 lines
- if (
window->direct&& (arg->start_pfn<<PAGE_SHIFT) < -ddw_memory_hotplug_max()) {
+ if (window->direct) {
ret |=tce_clearrange_multi_pSeriesLP(arg->start_pfn, - arg->nr_pages, window->prop);
+ limit,window->prop);
}
/* XXX log error */^^^ Ditto.
Thanks
HarshQuoted 19 lines
}
arch/powerpc/platforms/pseries/iommu.c +2
-0@@ -2532,6 +2548,14 @@ void __init iommu_init_early_pSeries(void) register_memory_notifier(&iommu_mem_nb); set_pci_dma_ops(&dma_iommu_ops); + + /* During init determine the max memory an LPAR can have and setit. This
+ * will be used for pre-mapping RAM in DDW.memblock_end_of_DRAM()can
+ * change during the running of LPAR - daxctl can add pmemory as + * "system-ram". This memory range should not be pre-mapped in DDW since
+ * the address of pmemory can be much higher than the DDW size. + */
+pseries_ddw_max_ram=ddw_memory_hotplug_max();
}
static int__initdisable_multitce(char *str)base-commit:
6d35786de28116ecf78797a62b84e6bf3c45aa5a