arm64: dts: ti: k3-j784s4/am69: Add uart, i2c, eeprom, misc
Subsystems (2)
Nishanth Menon
maintainercover arm64: dts: ti: k3-j784s4/am69: Add uart, i2c, eeprom, misc
Hi,
This series picks up from where [1] left off. After fixing the mux regions, introduce the basic i2c, uarts, ethernet, and a few alias fixups sprinkled along with it.
This series also takes over [2] and rebased on top of [1] and my series.
Test log:
Dasnavis Sabiya (1):
arm64: dts: ti: k3-am69-sk: Add pinmux for RPi Header
Nishanth Menon (7):
arm64: dts: ti: k3-j784s4-evm: Fix main_i2c0 alias
arm64: dts: ti: k3-j784s4-evm: Add mcu and wakeup uarts
arm64: dts: ti: k3-j784s4-evm: Enable wakeup_i2c0 and eeprom
arm64: dts: ti: k3-am69-sk: Fix main_i2c0 alias
arm64: dts: ti: k3-am69-sk: Enable mcu network port
arm64: dts: ti: k3-am69-sk: Add mcu and wakeup uarts
arm64: dts: ti: k3-am69-sk: Enable wakeup_i2c0 and eeprom
arch/arm64/boot/dts/ti/k3-am69-sk.dts | 165 ++++++++++++++++++++++- arch/arm64/boot/dts/ti/k3-j784s4-evm.dts | 56 +++++++- 2 files changed, 219 insertions(+), 2 deletions(-)
[1] https://lore.kernel.org/linux-arm-kernel/[email protected]/
[2] https://lore.kernel.org/linux-arm-kernel/[email protected]/
Signature · 1 line
2.40.0
Nishanth Menon
maintainerPATCH 1/8 arm64: dts: ti: k3-j784s4-evm: Fix main_i2c0 alias
main_i2c0 is aliased as i2c0 which creates a problem for u-boot R5 SPL attempting to reuse the same definition in the common board detection logic as it looks for the first i2c instance as the bus on which to detect the eeprom to understand the board variant involved. Switch main_i2c0 to i2c3 alias allowing us to introduce wkup_i2c0 and potentially space for mcu_i2c instances in the gap for follow on patches.
--- arch/arm64/boot/dts/ti/k3-j784s4-evm.dts | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
arch/arm64/boot/dts/ti/k3-j784s4-evm.dts +1 -1
@@ -23,7 +23,7 @@ aliases { serial2 = &main_uart8; mmc0 = &main_sdhci0; mmc1 = &main_sdhci1; - i2c0 = &main_i2c0; + i2c3 = &main_i2c0; }; memory@80000000 {
Signature · 1 line
2.40.0
Nishanth Menon
maintainerPATCH 2/8 arm64: dts: ti: k3-j784s4-evm: Add mcu and wakeup uarts
In reply to Nishanth MenonAdd wakeup and MCU uart. This allows the device tree usage in bootloader and firmwares that can configure the same appropriately.
---
Depends on https://lore.kernel.org/linux-arm-kernel/[email protected]/
arch/arm64/boot/dts/ti/k3-j784s4-evm.dts | 33 ++++++++++++++++++++++++ 1 file changed, 33 insertions(+)
arch/arm64/boot/dts/ti/k3-j784s4-evm.dts +33 -0
@@ -20,6 +20,8 @@ chosen { }; aliases { + serial0 = &wkup_uart0; + serial1 = &mcu_uart0; serial2 = &main_uart8; mmc0 = &main_sdhci0; mmc1 = &main_sdhci1;
@@ -142,6 +144,24 @@ J784S4_IOPAD(0x020, PIN_INPUT, 7) /* (AJ35) MCAN15_RX.GPIO0_8 */ }; &wkup_pmx2 { + wkup_uart0_pins_default: wkup-uart0-pins-default { + pinctrl-single,pins = < + J721S2_WKUP_IOPAD(0x070, PIN_INPUT, 0) /* (L37) WKUP_GPIO0_6.WKUP_UART0_CTSn */ + J721S2_WKUP_IOPAD(0x074, PIN_INPUT, 0) /* (L36) WKUP_GPIO0_7.WKUP_UART0_RTSn */ + J721S2_WKUP_IOPAD(0x048, PIN_INPUT, 0) /* (K35) WKUP_UART0_RXD */ + J721S2_WKUP_IOPAD(0x04c, PIN_INPUT, 0) /* (K34) WKUP_UART0_TXD */ + >; + }; + + mcu_uart0_pins_default: mcu-uart0-pins-default { + pinctrl-single,pins = < + J784S4_WKUP_IOPAD(0x090, PIN_INPUT, 0) /* (H37) WKUP_GPIO0_14.MCU_UART0_CTSn */ + J784S4_WKUP_IOPAD(0x094, PIN_OUTPUT, 0) /* (K37) WKUP_GPIO0_15.MCU_UART0_RTSn */ + J784S4_WKUP_IOPAD(0x08c, PIN_INPUT, 0) /* (K38) WKUP_GPIO0_13.MCU_UART0_RXD */ + J784S4_WKUP_IOPAD(0x088, PIN_OUTPUT, 0) /* (J37) WKUP_GPIO0_12.MCU_UART0_TXD */ + >; + }; + mcu_cpsw_pins_default: mcu-cpsw-pins-default { pinctrl-single,pins = < J784S4_WKUP_IOPAD(0x02c, PIN_INPUT, 0) /* (A35) MCU_RGMII1_RD0 */
@@ -167,6 +187,19 @@ J784S4_WKUP_IOPAD(0x030, PIN_INPUT, 0) /* (B35) MCU_MDIO0_MDIO */ }; }; +&wkup_uart0 { + /* Firmware usage */ + status = "reserved"; + pinctrl-names = "default"; + pinctrl-0 = <&wkup_uart0_pins_default>; +}; + +&mcu_uart0 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&mcu_uart0_pins_default>; +}; + &main_uart8 { status = "okay"; pinctrl-names = "default";
Signature · 1 line
2.40.0
Nishanth Menon
maintainerPATCH 3/8 arm64: dts: ti: k3-j784s4-evm: Enable wakeup_i2c0 and eeprom
In reply to Nishanth MenonEnable wakeup_i2c and use un-used pinmux. While at it, describe the board detection eeprom present on the board.
---
Depends on https://lore.kernel.org/linux-arm-kernel/[email protected]/
arch/arm64/boot/dts/ti/k3-j784s4-evm.dts | 21 +++++++++++++++++++++ 1 file changed, 21 insertions(+)
arch/arm64/boot/dts/ti/k3-j784s4-evm.dts +21 -0
@@ -25,6 +25,7 @@ aliases { serial2 = &main_uart8; mmc0 = &main_sdhci0; mmc1 = &main_sdhci1; + i2c0 = &wkup_i2c0; i2c3 = &main_i2c0; };
@@ -153,6 +154,13 @@ J721S2_WKUP_IOPAD(0x04c, PIN_INPUT, 0) /* (K34) WKUP_UART0_TXD */ >; }; + wkup_i2c0_pins_default: wkup-i2c0-pins-default { + pinctrl-single,pins = < + J721S2_WKUP_IOPAD(0x98, PIN_INPUT, 0) /* (N33) WKUP_I2C0_SCL */ + J721S2_WKUP_IOPAD(0x9c, PIN_INPUT, 0) /* (N35) WKUP_I2C0_SDA */ + >; + }; + mcu_uart0_pins_default: mcu-uart0-pins-default { pinctrl-single,pins = < J784S4_WKUP_IOPAD(0x090, PIN_INPUT, 0) /* (H37) WKUP_GPIO0_14.MCU_UART0_CTSn */
@@ -194,6 +202,19 @@ &wkup_uart0 { pinctrl-0 = <&wkup_uart0_pins_default>; }; +&wkup_i2c0 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&wkup_i2c0_pins_default>; + clock-frequency = <400000>; + + eeprom@50 { + /* CAV24C256WE-GT3 */ + compatible = "atmel,24c256"; + reg = <0x50>; + }; +}; + &mcu_uart0 { status = "okay"; pinctrl-names = "default";
Signature · 1 line
2.40.0
Nishanth Menon
maintainerPATCH 4/8 arm64: dts: ti: k3-am69-sk: Fix main_i2c0 alias
In reply to Nishanth Menonmain_i2c0 is aliased as i2c0 which creates a problem for u-boot R5 SPL attempting to reuse the same definition in the common board detection logic as it looks for the first i2c instance as the bus on which to detect the eeprom to understand the board variant involved. Switch main_i2c0 to i2c3 alias allowing us to introduce wkup_i2c0 and potentially space for mcu_i2c instances in the gap for follow on patches.
--- arch/arm64/boot/dts/ti/k3-am69-sk.dts | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
arch/arm64/boot/dts/ti/k3-am69-sk.dts +1 -1
@@ -23,7 +23,7 @@ chosen { aliases { serial2 = &main_uart8; mmc1 = &main_sdhci1; - i2c0 = &main_i2c0; + i2c3 = &main_i2c0; }; memory@80000000 {
Signature · 1 line
2.40.0
Nishanth Menon
maintainerPATCH 5/8 arm64: dts: ti: k3-am69-sk: Enable mcu network port
In reply to Nishanth MenonEnable networking for NFS and basic networking functionality.
---
Depends on https://lore.kernel.org/linux-arm-kernel/[email protected]/
arch/arm64/boot/dts/ti/k3-am69-sk.dts | 48 +++++++++++++++++++++++++++ 1 file changed, 48 insertions(+)
arch/arm64/boot/dts/ti/k3-am69-sk.dts +48 -0
@@ -24,6 +24,7 @@ aliases { serial2 = &main_uart8; mmc1 = &main_sdhci1; i2c3 = &main_i2c0; + ethernet0 = &mcu_cpsw_port1; }; memory@80000000 {
@@ -139,6 +140,32 @@ J784S4_IOPAD(0x0C4, PIN_INPUT, 7) /* (AD36) ECAP0_IN_APWM_OUT.GPIO0_49 */ }; }; +&wkup_pmx2 { + mcu_cpsw_pins_default: mcu-cpsw-pins-default { + pinctrl-single,pins = < + J784S4_WKUP_IOPAD(0x02c, PIN_INPUT, 0) /* (A35) MCU_RGMII1_RD0 */ + J784S4_WKUP_IOPAD(0x028, PIN_INPUT, 0) /* (B36) MCU_RGMII1_RD1 */ + J784S4_WKUP_IOPAD(0x024, PIN_INPUT, 0) /* (C36) MCU_RGMII1_RD2 */ + J784S4_WKUP_IOPAD(0x020, PIN_INPUT, 0) /* (D36) MCU_RGMII1_RD3 */ + J784S4_WKUP_IOPAD(0x01c, PIN_INPUT, 0) /* (B37) MCU_RGMII1_RXC */ + J784S4_WKUP_IOPAD(0x004, PIN_INPUT, 0) /* (C37) MCU_RGMII1_RX_CTL */ + J784S4_WKUP_IOPAD(0x014, PIN_OUTPUT, 0) /* (D37) MCU_RGMII1_TD0 */ + J784S4_WKUP_IOPAD(0x010, PIN_OUTPUT, 0) /* (D38) MCU_RGMII1_TD1 */ + J784S4_WKUP_IOPAD(0x00c, PIN_OUTPUT, 0) /* (E37) MCU_RGMII1_TD2 */ + J784S4_WKUP_IOPAD(0x008, PIN_OUTPUT, 0) /* (E38) MCU_RGMII1_TD3 */ + J784S4_WKUP_IOPAD(0x018, PIN_OUTPUT, 0) /* (E36) MCU_RGMII1_TXC */ + J784S4_WKUP_IOPAD(0x000, PIN_OUTPUT, 0) /* (C38) MCU_RGMII1_TX_CTL */ + >; + }; + + mcu_mdio_pins_default: mcu-mdio-pins-default { + pinctrl-single,pins = < + J784S4_WKUP_IOPAD(0x034, PIN_OUTPUT, 0) /* (A36) MCU_MDIO0_MDC */ + J784S4_WKUP_IOPAD(0x030, PIN_INPUT, 0) /* (B35) MCU_MDIO0_MDIO */ + >; + }; +}; + &main_uart8 { status = "okay"; pinctrl-names = "default";
@@ -178,3 +205,24 @@ &main_sdhci1 { &main_gpio0 { status = "okay"; }; + +&mcu_cpsw { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&mcu_cpsw_pins_default>, <&mcu_mdio_pins_default>; +}; + +&davinci_mdio { + mcu_phy0: ethernet-phy@0 { + reg = <0>; + ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>; + ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>; + ti,min-output-impedance; + }; +}; + +&mcu_cpsw_port1 { + status = "okay"; + phy-mode = "rgmii-rxid"; + phy-handle = <&mcu_phy0>; +};
Signature · 1 line
2.40.0
Nishanth Menon
maintainerPATCH 6/8 arm64: dts: ti: k3-am69-sk: Add mcu and wakeup uarts
In reply to Nishanth MenonAdd wakeup and MCU uart. This allows the device tree usage in bootloader and firmwares that can configure the same appropriately.
---
Depends on https://lore.kernel.org/linux-arm-kernel/[email protected]/
arch/arm64/boot/dts/ti/k3-am69-sk.dts | 31 +++++++++++++++++++++++++++ 1 file changed, 31 insertions(+)
arch/arm64/boot/dts/ti/k3-am69-sk.dts +31 -0
@@ -21,6 +21,8 @@ chosen { }; aliases { + serial0 = &wkup_uart0; + serial1 = &mcu_uart0; serial2 = &main_uart8; mmc1 = &main_sdhci1; i2c3 = &main_i2c0;
@@ -141,6 +143,22 @@ J784S4_IOPAD(0x0C4, PIN_INPUT, 7) /* (AD36) ECAP0_IN_APWM_OUT.GPIO0_49 */ }; &wkup_pmx2 { + wkup_uart0_pins_default: wkup-uart0-pins-default { + pinctrl-single,pins = < + J721S2_WKUP_IOPAD(0x070, PIN_INPUT, 0) /* (L37) WKUP_GPIO0_6.WKUP_UART0_CTSn */ + J721S2_WKUP_IOPAD(0x074, PIN_INPUT, 0) /* (L36) WKUP_GPIO0_7.WKUP_UART0_RTSn */ + J721S2_WKUP_IOPAD(0x048, PIN_INPUT, 0) /* (K35) WKUP_UART0_RXD */ + J721S2_WKUP_IOPAD(0x04c, PIN_INPUT, 0) /* (K34) WKUP_UART0_TXD */ + >; + }; + + mcu_uart0_pins_default: mcu-uart0-pins-default { + pinctrl-single,pins = < + J784S4_WKUP_IOPAD(0x08c, PIN_INPUT, 0) /* (K38) WKUP_GPIO0_13.MCU_UART0_RXD */ + J784S4_WKUP_IOPAD(0x088, PIN_OUTPUT, 0) /* (J37) WKUP_GPIO0_12.MCU_UART0_TXD */ + >; + }; + mcu_cpsw_pins_default: mcu-cpsw-pins-default { pinctrl-single,pins = < J784S4_WKUP_IOPAD(0x02c, PIN_INPUT, 0) /* (A35) MCU_RGMII1_RD0 */
@@ -166,6 +184,19 @@ J784S4_WKUP_IOPAD(0x030, PIN_INPUT, 0) /* (B35) MCU_MDIO0_MDIO */ }; }; +&wkup_uart0 { + /* Firmware usage */ + status = "reserved"; + pinctrl-names = "default"; + pinctrl-0 = <&wkup_uart0_pins_default>; +}; + +&mcu_uart0 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&mcu_uart0_pins_default>; +}; + &main_uart8 { status = "okay"; pinctrl-names = "default";
Signature · 1 line
2.40.0
Nishanth Menon
maintainerPATCH 7/8 arm64: dts: ti: k3-am69-sk: Enable wakeup_i2c0 and eeprom
In reply to Nishanth MenonEnable wakeup_i2c and use un-used pinmux. While at it, describe the board detection eeprom present on the board.
---
Depends on https://lore.kernel.org/linux-arm-kernel/[email protected]/
arch/arm64/boot/dts/ti/k3-am69-sk.dts | 21 +++++++++++++++++++++ 1 file changed, 21 insertions(+)
arch/arm64/boot/dts/ti/k3-am69-sk.dts +21 -0
@@ -25,6 +25,7 @@ aliases { serial1 = &mcu_uart0; serial2 = &main_uart8; mmc1 = &main_sdhci1; + i2c0 = &wkup_i2c0; i2c3 = &main_i2c0; ethernet0 = &mcu_cpsw_port1; };
@@ -152,6 +153,13 @@ J721S2_WKUP_IOPAD(0x04c, PIN_INPUT, 0) /* (K34) WKUP_UART0_TXD */ >; }; + wkup_i2c0_pins_default: wkup-i2c0-pins-default { + pinctrl-single,pins = < + J721S2_WKUP_IOPAD(0x98, PIN_INPUT, 0) /* (N33) WKUP_I2C0_SCL */ + J721S2_WKUP_IOPAD(0x9c, PIN_INPUT, 0) /* (N35) WKUP_I2C0_SDA */ + >; + }; + mcu_uart0_pins_default: mcu-uart0-pins-default { pinctrl-single,pins = < J784S4_WKUP_IOPAD(0x08c, PIN_INPUT, 0) /* (K38) WKUP_GPIO0_13.MCU_UART0_RXD */
@@ -191,6 +199,19 @@ &wkup_uart0 { pinctrl-0 = <&wkup_uart0_pins_default>; }; +&wkup_i2c0 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&wkup_i2c0_pins_default>; + clock-frequency = <400000>; + + eeprom@51 { + /* AT24C512C-MAHM-T */ + compatible = "atmel,24c512"; + reg = <0x51>; + }; +}; + &mcu_uart0 { status = "okay"; pinctrl-names = "default";
Signature · 1 line
2.40.0
Nishanth Menon
maintainerPATCH 8/8 arm64: dts: ti: k3-am69-sk: Add pinmux for RPi Header
In reply to Nishanth MenonFrom: Dasnavis Sabiya <[email protected]>
Add pinmux required to bring out the i2c and gpios on 40 pin RPi expansion header on AM69 SK board.
---
Depends on https://lore.kernel.org/linux-arm-kernel/[email protected]/
Changes since V1:
* Rebased on the pinmux split up done from the dependency.
* Some minor style fixups.
V1: https://lore.kernel.org/linux-arm-kernel/[email protected]/
arch/arm64/boot/dts/ti/k3-am69-sk.dts | 63 +++++++++++++++++++++++++++ 1 file changed, 63 insertions(+)
arch/arm64/boot/dts/ti/k3-am69-sk.dts +63 -0
@@ -141,6 +141,25 @@ vdd_sd_dv_pins_default: vdd-sd-dv-pins-default { J784S4_IOPAD(0x0C4, PIN_INPUT, 7) /* (AD36) ECAP0_IN_APWM_OUT.GPIO0_49 */ >; }; + + rpi_header_gpio0_pins_default: rpi-header-gpio0-pins-default { + pinctrl-single,pins = < + J784S4_IOPAD(0x0BC, PIN_INPUT, 7) /* (AD33) MCASP1_AFSX.GPIO0_47 */ + J784S4_IOPAD(0x06C, PIN_INPUT, 7) /* (AJ37) MCASP4_AFSX.GPIO0_27 */ + J784S4_IOPAD(0x0B4, PIN_INPUT, 7) /* (AL34) MCASP1_AXR4.GPIO0_45 */ + J784S4_IOPAD(0x0C0, PIN_INPUT, 7) /* (AD38) MCASP1_AXR0.GPIO0_48 */ + J784S4_IOPAD(0x00C, PIN_INPUT, 7) /* (AF33) MCAN13_TX.GPIO0_3 */ + J784S4_IOPAD(0x0B8, PIN_INPUT, 7) /* (AC34) MCASP1_ACLKX.GPIO0_46 */ + J784S4_IOPAD(0x090, PIN_INPUT, 7) /* (AC35) MCASP0_AXR8.GPIO0_36 */ + J784S4_IOPAD(0x0A8, PIN_INPUT, 7) /* (AF34) MCASP0_AXR14.GPIO0_42 */ + J784S4_IOPAD(0x0A4, PIN_INPUT, 7) /* (AJ36) MCASP0_AXR13.GPIO0_41 */ + J784S4_IOPAD(0x034, PIN_INPUT, 7) /* (AJ34) PMIC_WAKE0n.GPIO0_13 */ + J784S4_IOPAD(0x0CC, PIN_INPUT, 7) /* (AM37) SPI0_CS0.GPIO0_51 */ + J784S4_IOPAD(0x08C, PIN_INPUT, 7) /* (AE35) MCASP0_AXR7.GPIO0_35 */ + J784S4_IOPAD(0x008, PIN_INPUT, 7) /* (AJ33) MCAN12_RX.GPIO0_2 */ + J784S4_IOPAD(0x004, PIN_INPUT, 7) /* (AG36) MCAN12_TX.GPIO0_1 */ + >; + }; }; &wkup_pmx2 {
@@ -167,6 +186,13 @@ J784S4_WKUP_IOPAD(0x088, PIN_OUTPUT, 0) /* (J37) WKUP_GPIO0_12.MCU_UART0_TXD */ >; }; + mcu_i2c0_pins_default: mcu-i2c0-pins-default { + pinctrl-single,pins = < + J784S4_WKUP_IOPAD(0x0a0, PIN_INPUT_PULLUP, 0) /* (M35) MCU_I2C0_SCL */ + J784S4_WKUP_IOPAD(0x0a4, PIN_INPUT_PULLUP, 0) /* (G34) MCU_I2C0_SDA */ + >; + }; + mcu_cpsw_pins_default: mcu-cpsw-pins-default { pinctrl-single,pins = < J784S4_WKUP_IOPAD(0x02c, PIN_INPUT, 0) /* (A35) MCU_RGMII1_RD0 */
@@ -190,6 +216,28 @@ J784S4_WKUP_IOPAD(0x034, PIN_OUTPUT, 0) /* (A36) MCU_MDIO0_MDC */ J784S4_WKUP_IOPAD(0x030, PIN_INPUT, 0) /* (B35) MCU_MDIO0_MDIO */ >; }; + + mcu_rpi_hdr1_gpio0_pins_default: mcu-rpi-hdr1-gpio0-pins-default { + pinctrl-single,pins = < + J784S4_WKUP_IOPAD(0x118, PIN_INPUT, 7) /* (N34) WKUP_GPIO0_66 */ + J784S4_WKUP_IOPAD(0x05c, PIN_INPUT, 7) /* (J34) WKUP_GPIO0_1 */ + J784S4_WKUP_IOPAD(0x060, PIN_INPUT, 7) /* (J35) WKUP_GPIO0_2 */ + J784S4_WKUP_IOPAD(0x058, PIN_INPUT, 7) /* (H38) WKUP_GPIO0_0 */ + J784S4_WKUP_IOPAD(0x0b8, PIN_INPUT, 7) /* (M37) WKUP_GPIO0_56 */ + J784S4_WKUP_IOPAD(0x114, PIN_INPUT, 7) /* (M36) WKUP_GPIO0_57 */ + J784S4_WKUP_IOPAD(0x094, PIN_INPUT, 7) /* (K37) WKUP_GPIO0_15 */ + J784S4_WKUP_IOPAD(0x064, PIN_INPUT, 7) /* (J36) WKUP_GPIO0_3 */ + J784S4_WKUP_IOPAD(0x11c, PIN_INPUT, 7) /* (M34) WKUP_GPIO0_67 */ + >; + }; +}; + +&wkup_pmx3 { + mcu_rpi_hdr2_gpio0_pins_default: mcu-rpi-hdr2-gpio0-pins-default { + pinctrl-single,pins = < + J784S4_WKUP_IOPAD(0x0, PIN_INPUT, 7) /* (M33) WKUP_GPIO0_49 */ + >; + }; }; &wkup_uart0 {
@@ -212,12 +260,25 @@ eeprom@51 { }; }; +&wkup_gpio0 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&mcu_rpi_hdr1_gpio0_pins_default>, <&mcu_rpi_hdr2_gpio0_pins_default>; +}; + &mcu_uart0 { status = "okay"; pinctrl-names = "default"; pinctrl-0 = <&mcu_uart0_pins_default>; }; +&mcu_i2c0 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&mcu_i2c0_pins_default>; + clock-frequency = <400000>; +}; + &main_uart8 { status = "okay"; pinctrl-names = "default";
@@ -256,6 +317,8 @@ &main_sdhci1 { &main_gpio0 { status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&rpi_header_gpio0_pins_default>; }; &mcu_cpsw {
Signature · 1 line
2.40.0
Nishanth Menon
maintainerQuoted 9 lines · Nishanth Menon
Hi,
This series picks up from where [1] left off. After fixing the mux regions, introduce the basic i2c, uarts, ethernet, and a few alias fixups sprinkled along with it.
This series also takes over [2] and rebased on top of [1] and my series.
Test log:
Apologies on that, I seem to have forgotten to provide the link to the test log. Anyways, here we go:
https://gist.github.com/nmenon/dca0ea1203c4e06d77f77b5c4a4a3e3f
Quoted 22 lines
Dasnavis Sabiya (1):
arm64: dts: ti: k3-am69-sk: Add pinmux for RPi HeaderNishanth Menon (7):
arm64: dts: ti: k3-j784s4-evm: Fixmain_i2c0alias
arm64: dts: ti: k3-j784s4-evm: Add mcu and wakeup uarts
arm64: dts: ti: k3-j784s4-evm: Enablewakeup_i2c0and eeprom
arm64: dts: ti: k3-am69-sk: Fixmain_i2c0alias
arm64: dts: ti: k3-am69-sk: Enable mcu network port
arm64: dts: ti: k3-am69-sk: Add mcu and wakeup uarts
arm64: dts: ti: k3-am69-sk: Enablewakeup_i2c0and eepromarch/arm64/boot/dts/ti/k3-am69-sk.dts | 165 ++++++++++++++++++++++- arch/arm64/boot/dts/ti/k3-j784s4-evm.dts | 56 +++++++- 2 files changed, 219 insertions(+), 2 deletions(-)[1] https://lore.kernel.org/linux-arm-kernel/[email protected]/
[2] https://lore.kernel.org/linux-arm-kernel/[email protected]/Signature · 1 line
2.40.0
Signature · 3 lines
Regards, Nishanth Menon Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3 1A34 DDB5 849D 1736 249D
Thanks Nishanth
Quoted 22 lines · Nishanth Menon
Hi,
This series picks up from where [1] left off. After fixing the mux regions, introduce the basic i2c, uarts, ethernet, and a few alias fixups sprinkled along with it.
This series also takes over [2] and rebased on top of [1] and my series.
Test log:
Dasnavis Sabiya (1):
arm64: dts: ti: k3-am69-sk: Add pinmux for RPi HeaderNishanth Menon (7):
arm64: dts: ti: k3-j784s4-evm: Fixmain_i2c0alias
arm64: dts: ti: k3-j784s4-evm: Add mcu and wakeup uarts
arm64: dts: ti: k3-j784s4-evm: Enablewakeup_i2c0and eeprom
arm64: dts: ti: k3-am69-sk: Fixmain_i2c0alias
arm64: dts: ti: k3-am69-sk: Enable mcu network port
arm64: dts: ti: k3-am69-sk: Add mcu and wakeup uarts
arm64: dts: ti: k3-am69-sk: Enablewakeup_i2c0and eeprom
Quoted 3 lines
arch/arm64/boot/dts/ti/k3-am69-sk.dts | 165 ++++++++++++++++++++++- arch/arm64/boot/dts/ti/k3-j784s4-evm.dts | 56 +++++++- 2 files changed, 219 insertions(+), 2 deletions(-)
Hi Nishanth Menon,
Quoted 9 lines · Nishanth Menon
This series picks up from where [1] left off. After fixing the mux regions, introduce the basic i2c, uarts, ethernet, and a few alias fixups sprinkled along with it.
This series also takes over [2] and rebased on top of [1] and my series.
Test log:
[...]
I have applied the following to branch ti-k3-dts-next on [1]. Thank you!
[1/8] arm64: dts: ti: k3-j784s4-evm: Fix main_i2c0 alias
commit: c10a9df30e3401bd5a5ee43f1afd6c2b2ca75ad7
[2/8] arm64: dts: ti: k3-j784s4-evm: Add mcu and wakeup uarts
commit: 6fa5d37a2f34476613012789d4618c3dc6c68b35
[3/8] arm64: dts: ti: k3-j784s4-evm: Enable wakeup_i2c0 and eeprom
commit: 5dfbd1debc8ce5123310265cd44b5d99d272b1fe
[4/8] arm64: dts: ti: k3-am69-sk: Fix main_i2c0 alias
commit: b38c6ced4ec5b3f6260ff6cc2b71e8a3d8c897d7
[5/8] arm64: dts: ti: k3-am69-sk: Enable mcu network port
commit: 7b72bd25508de6a5eee2cb1679b9d4b8bc25de5a
[6/8] arm64: dts: ti: k3-am69-sk: Add mcu and wakeup uarts
commit: 45299dd1991b496ddab5ab4a86d7ae601e0e4c7f
[7/8] arm64: dts: ti: k3-am69-sk: Enable wakeup_i2c0 and eeprom
commit: 08ae12b637507cd22fbcdb82521b8b8a5ae96222
[8/8] arm64: dts: ti: k3-am69-sk: Add pinmux for RPi Header
commit: 0ec1a48d99ddd11c265f7f1b2573fb2c8e0db0abAll being well this means that it will be integrated into the linux-next tree (usually sometime in the next 24 hours) and sent up the chain during the next merge window (or sooner if it is a relevant bug fix), however if problems are discovered then the patch may be dropped or reverted.
You may get further e-mails resulting from automated or manual testing and review of the tree, please engage with people reporting problems and send followup patches addressing any issues that are reported if needed.
If any updates are required or you are submitting further changes they should be sent as incremental updates against current git, existing patches will not be replaced.
Please add any relevant lists and maintainers to the CCs when replying to this mail.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/ti/linux.git
--
Vignesh
_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel