scsi: sd: Use UNMAP in case the device doesn't support WRITE_SAME
PATCH 1/1 scsi: sd: Use UNMAP in case the device doesn't support WRITE_SAME
From: Bean Huo <[email protected]>
There exists a storage device that supports READ_CAPACITY, but doesn't support WRITE_SAME. The problem is that WRITE SAME heuristics doesn't work for this kind of storage device since its block limits VPD page doesn't contain the LBP information. Currently we set its provisioning_mode "writesame_16" and didn't check "no_write_same". If we didn't manually change this default provisioning_mode to "unmap" through sysfs, provisioning_mode will be set to "disabled" after the first WRITE_SAME command with the following error occurs:
sd 0:0:0:3: [sdd] tag#4 UNKNOWN(0x2003) Result: hostbyte=0x00 driverbyte=0x08 cmd_age=0s
sd 0:0:0:3: [sdd] tag#4 Sense Key : 0x5 [current]
sd 0:0:0:3: [sdd] tag#4 ASC=0x20 ASCQ=0x0
sd 0:0:0:3: [sdd] tag#4 CDB: opcode=0x93 93 08 00 00 00 00 00 00 05 4b 00 00 00 1f 00 00blk_update_request: critical target error, dev sdd, sector 10840 op 0x3:(DISCARD) flags 0x800 phys_seg 1 prio class 0
Comparing to manually change provisioning_mode in sysfs, it is better to set provisioning_mode to "unmap" in case WRITE_SAME is not supported.
--- drivers/scsi/sd.c | 5 ++++- 1 file changed, 4 insertions(+), 1 deletion(-)
drivers/scsi/sd.c +4 -1
@@ -2372,7 +2372,10 @@ static int read_capacity_16(struct scsi_disk *sdkp, struct scsi_device *sdp,if (buffer[14 ] &0x40 )/* LBPRZ */ sdkp->lbprz =1 ; -sd_config_discard (sdkp,SD_LBP_WS16 ); +if (sdp->no_write_same) +sd_config_discard (sdkp,SD_LBP_UNMAP ); +else +sd_config_discard (sdkp,SD_LBP_WS16 ); } sdkp->capacity = lba +1 ;
Signature · 1 line
2.17.1
Bean,
Quoted 5 lines
There exists a storage device that supports
READ_CAPACITY, but doesn't supportWRITE_SAME. The problem is that WRITE SAME heuristics doesn't work for this kind of storage device since its block limits VPD page doesn't contain the LBP information. Currently we set itsprovisioning_mode"writesame_16" and didn't check "no_write_same".
There is something odd with what your device is reporting.
We support WRITE SAME on a bunch of devices that predate the Logical Block Provisioning VPD page and the various Block Limits parameters being introduced to the spec. Consequently we set the provisioning mode to "writesame_16" if the device reports LBPME=1 in READ CAPACITY(16) and nothing relevant is reported in the VPD pages. That is by design.
Quoted 3 lines
If we didn't manually change this default
provisioning_modeto "unmap" through sysfs,provisioning_modewill be set to "disabled" after the firstWRITE_SAMEcommand with the following error occurs:
If your device supports UNMAP it *must* report it in the Logical Block Provisioning VPD by setting LBPU=1 and report MAXIMUM UNMAP LBA COUNT and MAXIMUM UNMAP BLOCK DESCRIPTOR COUNT in the Block Limits VPD.
Also, "no_write_same" disables attempting to use WRITE SAME to zero block ranges. That's orthogonal to the logic controlling which command to use for performing an unmap operation. An unfortunate choice of naming which can be attributed to the SCSI protocol using the WRITE SAME command for two completely different operations.
Signature · 1 line
Martin K. Petersen Oracle Linux Engineering
Quoted 28 lines · Martin K. Petersen
Quoted 6 lines
support
WRITE_SAME. The problem is that WRITE SAME heuristics doesn't work
for this kind of storage device since its block limits VPD page doesn't
contain the LBP information. Currently we set itsprovisioning_mode"writesame_16" and didn't check "no_write_same".There is something odd with what your device is reporting.
We support WRITE SAME on a bunch of devices that predate the Logical Block Provisioning VPD page and the various Block Limits parameters being introduced to the spec. Consequently we set the provisioning mode
to "writesame_16" if the device reports LBPME=1 in READ CAPACITY(16) and
nothing relevant is reported in the VPD pages. That is by design.Quoted 5 lines
If we didn't manually change this default
provisioning_modeto "unmap"
through sysfs,provisioning_modewill be set to "disabled" after the
firstWRITE_SAMEcommand with the following error occurs:If your device supports UNMAP it *must* report it in the Logical Block
Provisioning VPD by setting LBPU=1 and report MAXIMUM UNMAP LBA COUNT and MAXIMUM UNMAP BLOCK DESCRIPTOR COUNT in the Block Limits VPD.
Quoted 8 lines
Also, "
no_write_same" disables attempting to use WRITE SAME to zero block ranges. That's orthogonal to the logic controlling which command
to use for performing an unmap operation. An unfortunate choice of naming which can be attributed to the SCSI protocol using the WRITE SAME
command for two completely different operations.
Hi Martin
thanks very much for your above comments, very detailed. The case I encountered is very strange to me as well. I will double check on the product level.
thanks,
Bean