Tx power setting
Hi,
We are trying to change the tx power of QCA 9880.
We use 3.16.1 linux kernel and backport (3.16.1) to use the emerging ath10k device driver and 10.1.467.2-1 firmware.
However, we can not change the tx power setting (default 0 dBm) by using iw or iwconfig commands. Based on my understanding, if we change the tx power using the commands, ath10k_config() function should be invoked. However, the function is not called.
And the received signal strength at the receiver side does not change.
If you have any idea, please let me know.
Thank you.
Signature · 7 lines
Okhwan Lee Sent with Airmail _______________________________________________ ath10k mailing list [email protected] http://lists.infradead.org/mailman/listinfo/ath10k
Quoted 6 lines · Okhwan Lee
Hi,
We are trying to change the tx power of QCA 9880.
We use 3.16.1 linux kernel and backport (3.16.1) to use the emerging ath10k device driver and 10.1.467.2-1 firmware.However, we can not change the tx power setting (default 0 dBm) by using iw or iwconfig commands.
What do you mean "can not change". Do you get an error message? Where does it say you have 0 dBm as the default?
Quoted 5 lines
Based on my understanding, if we change the tx power using the commands,
ath10k_config()function should be invoked. However, the function is not called.
And the received signal strength at the receiver side does not change.If you have any idea, please let me know.
I'm using fbb5c042800ec42459a5cc307dec566d8e316927 from github.com/kvalo/ath/ (based on 3.17). I don't see the problem you describe - I can change tx powed with, e.g. iw wlan1 set txpower fixed 1000. The other end reports different signal strength values when I change txpower. Can you re-test with latest ath10k code, please?
Michał
_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k
Hi all,
Thank you for the answer.
As you said, if we use the most recent version of ath10k, it works correctly.
Signature · 4 lines
Okhwan Lee Sent with Airmail 켜짐 2014년 11월 5일 에서 오후 10:54:55, Michal Kazior ([email protected](mailto:[email protected])) 작성됨:
Quoted 26 lines · Okhwan Lee
Quoted 6 lines
Hi,
We are trying to change the tx power of QCA 9880.
We use 3.16.1 linux kernel and backport (3.16.1) to use the emerging ath10k device driver and 10.1.467.2-1 firmware.However, we can not change the tx power setting (default 0 dBm) by using iw or iwconfig commands.
What do you mean "can not change". Do you get an error message? Where does it say you have 0 dBm as the default?
Quoted 5 lines
Based on my understanding, if we change the tx power using the commands,
ath10k_config()function should be invoked. However, the function is not called.
And the received signal strength at the receiver side does not change.If you have any idea, please let me know.
I'm using
fbb5c042800ec42459a5cc307dec566d8e316927from github.com/kvalo/ath/ (based on 3.17). I don't see the problem you describe - I can change tx powed with, e.g.iw wlan1 set txpower fixed 1000. The other end reports different signal strength values when I change txpower. Can you re-test with latest ath10k code, please?
Quoted 1 line
Michał
_______________________________________________
ath10k mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/ath10k