app/testpmd: expand noisy neighbour forward mode support
PATCH v3 1/1 app/testpmd: expand noisy neighbour forward mode support
Previously the noisy neighbour vnf simulation would only operate in io mode, forwarding packets as is. However, this limited the usefulness of noisy neighbour simulation.
This feature has now been expanded to supporting mac, macswap, and 5tswap modes. To facilitate adding this support, some new header files were added.
---
v2: Reverted changes to random memory lookup
v3: Refactored entire patch
--- app/test-pmd/5tswap.c | 118 +---------------------- app/test-pmd/5tswap.h | 130 ++++++++++++++++++++++++++ app/test-pmd/macfwd.c | 33 +------ app/test-pmd/macfwd.h | 46 +++++++++ app/test-pmd/noisy_vnf.c | 92 +++++++++++++++--- app/test-pmd/parameters.c | 17 ++++ app/test-pmd/testpmd.c | 5 + app/test-pmd/testpmd.h | 8 ++ doc/guides/testpmd_app_ug/run_app.rst | 9 ++ 9 files changed, 299 insertions(+), 159 deletions(-) create mode 100644 app/test-pmd/5tswap.h create mode 100644 app/test-pmd/macfwd.h
app/test-pmd/5tswap.c +3 -115
@@ -17,64 +17,8 @@#include <rte_ip.h> #include <rte_flow.h> -#include "macswap_common.h" #include "testpmd.h" - - -static inline void -swap_mac (struct rte_ether_hdr *eth_hdr) -{ -struct rte_ether_addr addr; - -/* Swap dest and src mac addresses. */ -rte_ether_addr_copy (ð_hdr->dst_addr, &addr); -rte_ether_addr_copy (ð_hdr->src_addr, ð_hdr->dst_addr); -rte_ether_addr_copy (&addr, ð_hdr->src_addr); -} - -static inline void -swap_ipv4 (struct rte_ipv4_hdr *ipv4_hdr) -{ -rte_be32_t addr; - -/* Swap dest and src ipv4 addresses. */ - addr = ipv4_hdr->src_addr; - ipv4_hdr->src_addr = ipv4_hdr->dst_addr; - ipv4_hdr->dst_addr = addr; -} - -static inline void -swap_ipv6 (struct rte_ipv6_hdr *ipv6_hdr) -{ -uint8_t addr[16 ]; - -/* Swap dest and src ipv6 addresses. */ -memcpy (&addr, &ipv6_hdr->src_addr,16 ); -memcpy (&ipv6_hdr->src_addr, &ipv6_hdr->dst_addr,16 ); -memcpy (&ipv6_hdr->dst_addr, &addr,16 ); -} - -static inline void -swap_tcp (struct rte_tcp_hdr *tcp_hdr) -{ -rte_be16_t port; - -/* Swap dest and src tcp port. */ - port = tcp_hdr->src_port; - tcp_hdr->src_port = tcp_hdr->dst_port; - tcp_hdr->dst_port = port; -} - -static inline void -swap_udp (struct rte_udp_hdr *udp_hdr) -{ -rte_be16_t port; - -/* Swap dest and src udp port */ - port = udp_hdr->src_port; - udp_hdr->src_port = udp_hdr->dst_port; - udp_hdr->dst_port = port; -} +#include "5tswap.h" /* * 5 tuple swap forwarding mode: Swap the source and the destination of layers
@@ -85,22 +29,7 @@ static bool pkt_burst_5tuple_swap(struct fwd_stream *fs) {struct rte_mbuf *pkts_burst[MAX_PKT_BURST ]; -struct rte_port *txp; -struct rte_mbuf *mb; -uint16_t next_proto; -uint64_t ol_flags; -uint16_t proto;uint16_t nb_rx; -int i; -union { -struct rte_ether_hdr *eth; -struct rte_vlan_hdr *vlan; -struct rte_ipv4_hdr *ipv4; -struct rte_ipv6_hdr *ipv6; -struct rte_tcp_hdr *tcp; -struct rte_udp_hdr *udp; -uint8_t *byte; - } h;/* * Receive a burst of packets and forward them.
@@ -109,49 +38,8 @@ pkt_burst_5tuple_swap(struct fwd_stream *fs)if (unlikely (nb_rx ==0 ))return false; - txp = &ports[fs->tx_port]; - ol_flags =ol_flags_init (txp->dev_conf.txmode.offloads); -vlan_qinq_set (pkts_burst, nb_rx, ol_flags, - txp->tx_vlan_id, txp->tx_vlan_id_outer); -for (i =0 ; i < nb_rx; i++) { -if (likely (i < nb_rx -1 )) -rte_prefetch0 (rte_pktmbuf_mtod (pkts_burst[i+1 ], - void *)); - mb = pkts_burst[i]; - h.eth = rte_pktmbuf_mtod(mb, struct rte_ether_hdr *); - proto = h.eth->ether_type; -swap_mac (h.eth); - mb->l2_len =sizeof (struct rte_ether_hdr ); - h.eth++; -while (proto ==RTE_BE16 (RTE_ETHER_TYPE_VLAN ) || - proto ==RTE_BE16 (RTE_ETHER_TYPE_QINQ )) { - proto = h.vlan->eth_proto; - h.vlan++; - mb->l2_len +=sizeof (struct rte_vlan_hdr ); - } -if (proto ==RTE_BE16 (RTE_ETHER_TYPE_IPV4 )) { -swap_ipv4 (h.ipv4); - next_proto = h.ipv4->next_proto_id; - mb->l3_len =rte_ipv4_hdr_len (h.ipv4); - h.byte += mb->l3_len; - }else if (proto ==RTE_BE16 (RTE_ETHER_TYPE_IPV6 )) { -swap_ipv6 (h.ipv6); - next_proto = h.ipv6->proto; - h.ipv6++; - mb->l3_len =sizeof (struct rte_ipv6_hdr ); - }else { -mbuf_field_set (mb, ol_flags); -continue ; - } -if (next_proto ==IPPROTO_UDP ) { -swap_udp (h.udp); - mb->l4_len =sizeof (struct rte_udp_hdr ); - }else if (next_proto ==IPPROTO_TCP ) { -swap_tcp (h.tcp); - mb->l4_len = (h.tcp->data_off &0xf0 ) >>2 ; - } -mbuf_field_set (mb, ol_flags); - } +do_5tswap (pkts_burst, nb_rx, fs); +common_fwd_stream_transmit (fs, pkts_burst, nb_rx);return true;
app/test-pmd/5tswap.h new file +130 -0
130 lines not on this page · raw message
app/test-pmd/macfwd.c +2 -31
@@ -35,6 +35,7 @@#include <rte_flow.h> #include "testpmd.h" +#include "macfwd.h" /* * Forwarding of packets in MAC mode.
@@ -45,13 +46,7 @@ static bool pkt_burst_mac_forward(struct fwd_stream *fs) {struct rte_mbuf *pkts_burst[MAX_PKT_BURST ]; -struct rte_port *txp; -struct rte_mbuf *mb; -struct rte_ether_hdr *eth_hdr;uint16_t nb_rx; -uint16_t i; -uint64_t ol_flags =0 ; -uint64_t tx_offloads;/* * Receive a burst of packets and forward them.
@@ -60,31 +55,7 @@ pkt_burst_mac_forward(struct fwd_stream *fs)if (unlikely (nb_rx ==0 ))return false; - txp = &ports[fs->tx_port]; - tx_offloads = txp->dev_conf.txmode.offloads; -if (tx_offloads &RTE_ETH_TX_OFFLOAD_VLAN_INSERT ) - ol_flags =RTE_MBUF_F_TX_VLAN ; -if (tx_offloads &RTE_ETH_TX_OFFLOAD_QINQ_INSERT ) - ol_flags |=RTE_MBUF_F_TX_QINQ ; -if (tx_offloads &RTE_ETH_TX_OFFLOAD_MACSEC_INSERT ) - ol_flags |=RTE_MBUF_F_TX_MACSEC ; -for (i =0 ; i < nb_rx; i++) { -if (likely (i < nb_rx -1 )) -rte_prefetch0 (rte_pktmbuf_mtod (pkts_burst[i +1 ], - void *)); - mb = pkts_burst[i]; - eth_hdr = rte_pktmbuf_mtod(mb, struct rte_ether_hdr *); -rte_ether_addr_copy (&peer_eth_addrs[fs->peer_addr], - ð_hdr->dst_addr); -rte_ether_addr_copy (&ports[fs->tx_port].eth_addr, - ð_hdr->src_addr); - mb->ol_flags &=RTE_MBUF_F_INDIRECT |RTE_MBUF_F_EXTERNAL ; - mb->ol_flags |= ol_flags; - mb->l2_len =sizeof (struct rte_ether_hdr ); - mb->l3_len =sizeof (struct rte_ipv4_hdr ); - mb->vlan_tci = txp->tx_vlan_id; - mb->vlan_tci_outer = txp->tx_vlan_id_outer; - } +do_macfwd (pkts_burst, nb_rx, fs);common_fwd_stream_transmit (fs, pkts_burst, nb_rx);
app/test-pmd/macfwd.h new file +46 -0
46 lines not on this page · raw message
app/test-pmd/noisy_vnf.c +79 -13
144 lines not on this page · raw message
app/test-pmd/parameters.c +17 -0
@@ -196,6 +196,7 @@ usage(char* progname)printf (" --noisy-lkup-num-writes=N: do N random writes per packet\n" );printf (" --noisy-lkup-num-reads=N: do N random reads per packet\n" );printf (" --noisy-lkup-num-reads-writes=N: do N random reads and writes per packet\n" ); +printf (" --noisy-fwd-mode=mode: set the fwd mode\n" );printf (" --no-iova-contig: mempool memory can be IOVA non contiguous. " "valid only with --mp-alloc=anon\n" ); printf(" --rx-mq-mode=0xX: hexadecimal bitmask of RX mq mode can be "
@@ -704,6 +705,7 @@ launch_args_parse(int argc, char** argv) { "noisy-lkup-num-writes", 1, 0, 0 }, { "noisy-lkup-num-reads", 1, 0, 0 }, { "noisy-lkup-num-reads-writes", 1, 0, 0 }, + { "noisy-fwd-mode", 1, 0, 0 }, { "no-iova-contig", 0, 0, 0 }, { "rx-mq-mode", 1, 0, 0 }, { "record-core-cycles", 0, 0, 0 },
@@ -1444,6 +1446,21 @@ launch_args_parse(int argc, char** argv)rte_exit (EXIT_FAILURE ,"noisy-lkup-num-reads-writes must be >= 0\n" ); } +if (!strcmp (lgopts[opt_idx].name, +"noisy-fwd-mode" )) { +if (!strcmp (optarg,"io" )) + noisy_fwd_mode =NOISY_FWD_MODE_IO ; +else if (!strcmp (optarg,"mac" )) + noisy_fwd_mode =NOISY_FWD_MODE_MAC ; +else if (!strcmp (optarg,"macswap" )) + noisy_fwd_mode =NOISY_FWD_MODE_MACSWAP ; +else if (!strcmp (optarg,"5tswap" )) + noisy_fwd_mode =NOISY_FWD_MODE_5TSWAP ; +else +rte_exit (EXIT_FAILURE ,"noisy-fwd-mode %s invalid -" +" must b a valid fwd mode\n" , + optarg); + }if (!strcmp (lgopts[opt_idx].name,"no-iova-contig" )) mempool_flags =RTE_MEMPOOL_F_NO_IOVA_CONTIG ;
app/test-pmd/testpmd.c +5 -0
@@ -364,6 +364,11 @@ uint64_t noisy_lkup_num_reads;*/ uint64_t noisy_lkup_num_reads_writes; +/* +* Configurable forwarding mode in VNF simulation. +*/ +int noisy_fwd_mode; +/* * Receive Side Scaling (RSS) configuration. */
app/test-pmd/testpmd.h +8 -0
@@ -116,6 +116,13 @@ enum { QUEUE_JOB_TYPE_ACTION_QUERY, }; +enum { +NOISY_FWD_MODE_IO , +NOISY_FWD_MODE_MAC , +NOISY_FWD_MODE_MACSWAP , +NOISY_FWD_MODE_5TSWAP +}; +/** * The data structure associated with RX and TX packet burst statistics * that are recorded for each forwarding stream.
@@ -561,6 +568,7 @@ extern uint64_t noisy_lkup_mem_sz;extern uint64_t noisy_lkup_num_writes;extern uint64_t noisy_lkup_num_reads;extern uint64_t noisy_lkup_num_reads_writes; +extern int noisy_fwd_mode;extern uint8_t dcb_config;
doc/guides/testpmd_app_ug/run_app.rst +9 -0
@@ -519,6 +519,15 @@ The command line options are: Set the number of r/w accesses to be done in noisy neighbor simulation memory buffer to N. Only available with the noisy forwarding mode. The default value is 0. +* ``--noisy-fwd-mode=mode`` + + Set the noisy vnf forwarding mode where ``mode`` is one of the following:: + + io (the default) + mac + macswap + 5tswap + * ``--no-iova-contig`` Enable to create mempool which is not IOVA contiguous. Valid only with --mp-alloc=anon.
Signature · 1 line
2.31.1
Quoted 8 lines · Mike Pattrick
Previously the noisy neighbour vnf simulation would only operate in io mode, forwarding packets as is. However, this limited the usefulness of noisy neighbour simulation.
This feature has now been expanded to supporting mac, macswap, and 5tswap modes. To facilitate adding this support, some new header files were added.
Hi Mike,
I think it makes sense to allow these functionalities to be combined. It does seem like that noisy neighbour shouldn't have been added as a standalone fowarding option in the first place, as it's not mutually exclusive with the other fwding modes. Now it's forcing a user to set a fwding mode within a fwding mode to combine the functionality :/
The approach is to allow the fwding modes to expose their forwarding method so noisy can call them. Did you consider to expose the noisy functionality and allow the other forwarding modes to call that when the --noisy-* flags are set?
For example, a user sets fwding mode as normal 'fwd=macfwd' but then if the user adds the --noisy-* params, the macfwd'ing mode calls some functions exposed to add the noise, which seems a bit more intuitive.
Also, if someone adds a new fwding mode, they can just call the noisy functions and don't have update noisy fwding mode to add the new mode.
I'm not sure if it's better, just throwing it out there as an alternative idea.
On the downside, it would break backwards compatibility because previously those --noisy-* params would have had no effect with say macfwd mode, but now they will. So maybe that's enough to prohibit it.
In the past, I would have had all the params set and just changed fwdmode to enable/disable noisy vnf. That would behaviour would now be changed with this approach.
What do you think?
Few comments on the code below.
thanks,
Kevin.
Quoted 150 lines
Signed-off-by Mike Pattrick <[email protected]>---
v2: Reverted changes to random memory lookup
v3: Refactored entire patch--- app/test-pmd/5tswap.c | 118 +---------------------- app/test-pmd/5tswap.h | 130 ++++++++++++++++++++++++++ app/test-pmd/macfwd.c | 33 +------ app/test-pmd/macfwd.h | 46 +++++++++ app/test-pmd/noisy_vnf.c | 92 +++++++++++++++--- app/test-pmd/parameters.c | 17 ++++ app/test-pmd/testpmd.c | 5 + app/test-pmd/testpmd.h | 8 ++ doc/guides/testpmd_app_ug/run_app.rst | 9 ++ 9 files changed, 299 insertions(+), 159 deletions(-)create mode 100644
app/test-pmd/5tswap.h
create mode 100644app/test-pmd/macfwd.happ/test-pmd/5tswap.c +1
-107@@ -17,64 +17,8 @@#include <rte_ip.h> #include <rte_flow.h> -#include "macswap_common.h" #include "testpmd.h" - - -static inline void -swap_mac (struct rte_ether_hdr *eth_hdr) -{ -struct rte_ether_addr addr; - -/* Swap dest and src mac addresses. */ -rte_ether_addr_copy (ð_hdr->dst_addr, &addr); -rte_ether_addr_copy (ð_hdr->src_addr, ð_hdr->dst_addr); -rte_ether_addr_copy (&addr, ð_hdr->src_addr); -} - -static inline void -swap_ipv4 (struct rte_ipv4_hdr *ipv4_hdr) -{ -rte_be32_t addr; - -/* Swap dest and src ipv4 addresses. */ - addr = ipv4_hdr->src_addr; - ipv4_hdr->src_addr = ipv4_hdr->dst_addr; - ipv4_hdr->dst_addr = addr; -} - -static inline void -swap_ipv6 (struct rte_ipv6_hdr *ipv6_hdr) -{ -uint8_t addr[16 ]; - -/* Swap dest and src ipv6 addresses. */ -memcpy (&addr, &ipv6_hdr->src_addr,16 ); -memcpy (&ipv6_hdr->src_addr, &ipv6_hdr->dst_addr,16 ); -memcpy (&ipv6_hdr->dst_addr, &addr,16 ); -} - -static inline void -swap_tcp (struct rte_tcp_hdr *tcp_hdr) -{ -rte_be16_t port; - -/* Swap dest and src tcp port. */ - port = tcp_hdr->src_port; - tcp_hdr->src_port = tcp_hdr->dst_port; - tcp_hdr->dst_port = port; -} - -static inline void -swap_udp (struct rte_udp_hdr *udp_hdr) -{ -rte_be16_t port; - -/* Swap dest and src udp port */ - port = udp_hdr->src_port; - udp_hdr->src_port = udp_hdr->dst_port; - udp_hdr->dst_port = port; -} +#include "5tswap.h" /* * 5 tuple swap forwarding mode: Swap the source and the destination of layers @@ -85,22 +29,7 @@ static bool pkt_burst_5tuple_swap(struct fwd_stream *fs) {struct rte_mbuf *pkts_burst[MAX_PKT_BURST ]; -struct rte_port *txp; -struct rte_mbuf *mb; -uint16_t next_proto; -uint64_t ol_flags; -uint16_t proto;uint16_t nb_rx; -int i; -union { -struct rte_ether_hdr *eth; -struct rte_vlan_hdr *vlan; -struct rte_ipv4_hdr *ipv4; -struct rte_ipv6_hdr *ipv6; -struct rte_tcp_hdr *tcp; -struct rte_udp_hdr *udp; -uint8_t *byte; - } h;/* * Receive a burst of packets and forward them. @@ -109,49 +38,8 @@ pkt_burst_5tuple_swap(struct fwd_stream *fs)if (unlikely (nb_rx ==0 ))return false; - txp = &ports[fs->tx_port]; - ol_flags =ol_flags_init (txp->dev_conf.txmode.offloads); -vlan_qinq_set (pkts_burst, nb_rx, ol_flags, - txp->tx_vlan_id, txp->tx_vlan_id_outer); -for (i =0 ; i < nb_rx; i++) { -if (likely (i < nb_rx -1 )) -rte_prefetch0 (rte_pktmbuf_mtod (pkts_burst[i+1 ], - void *)); - mb = pkts_burst[i]; - h.eth = rte_pktmbuf_mtod(mb, struct rte_ether_hdr *); - proto = h.eth->ether_type; -swap_mac (h.eth); - mb->l2_len =sizeof (struct rte_ether_hdr ); - h.eth++; -while (proto ==RTE_BE16 (RTE_ETHER_TYPE_VLAN ) || - proto ==RTE_BE16 (RTE_ETHER_TYPE_QINQ )) { - proto = h.vlan->eth_proto; - h.vlan++; - mb->l2_len +=sizeof (struct rte_vlan_hdr ); - } -if (proto ==RTE_BE16 (RTE_ETHER_TYPE_IPV4 )) { -swap_ipv4 (h.ipv4); - next_proto = h.ipv4->next_proto_id; - mb->l3_len =rte_ipv4_hdr_len (h.ipv4); - h.byte += mb->l3_len; - }else if (proto ==RTE_BE16 (RTE_ETHER_TYPE_IPV6 )) { -swap_ipv6 (h.ipv6); - next_proto = h.ipv6->proto; - h.ipv6++; - mb->l3_len =sizeof (struct rte_ipv6_hdr ); - }else { -mbuf_field_set (mb, ol_flags); -continue ; - } -if (next_proto ==IPPROTO_UDP ) {
app/test-pmd/5tswap.c pkt_burst_5tuple_swap(struct fwd_stream *fs) · line 42
Quoted 10 lines
app/test-pmd/5tswap.c +2
-8-swap_udp (h.udp); - mb->l4_len =sizeof (struct rte_udp_hdr ); - }else if (next_proto ==IPPROTO_TCP ) { -swap_tcp (h.tcp); - mb->l4_len = (h.tcp->data_off &0xf0 ) >>2 ; - } -mbuf_field_set (mb, ol_flags); - } +do_5tswap (pkts_burst, nb_rx, fs); +
this simplification is nice.
Quoted 204 lines
app/test-pmd/5tswap.c +0
-0common_fwd_stream_transmit (fs, pkts_burst, nb_rx);return true;app/test-pmd/5tswap.h new file +130
-0@@ -0,0 +1,130 @@ +/* SPDX-License-Identifier: BSD-3-Clause +* Copyright(c) 2018 Intel Corporation +*/ + +#ifndef _5TSWAP_H_ +#define _5TSWAP_H_ + +#include "macswap_common.h" + +static inline void +swap_mac (struct rte_ether_hdr *eth_hdr) +{ +struct rte_ether_addr addr; + +/* Swap dest and src mac addresses. */ +rte_ether_addr_copy (ð_hdr->dst_addr, &addr); +rte_ether_addr_copy (ð_hdr->src_addr, ð_hdr->dst_addr); +rte_ether_addr_copy (&addr, ð_hdr->src_addr); +} + +static inline void +swap_ipv4 (struct rte_ipv4_hdr *ipv4_hdr) +{ +rte_be32_t addr; + +/* Swap dest and src ipv4 addresses. */ + addr = ipv4_hdr->src_addr; + ipv4_hdr->src_addr = ipv4_hdr->dst_addr; + ipv4_hdr->dst_addr = addr; +} + +static inline void +swap_ipv6 (struct rte_ipv6_hdr *ipv6_hdr) +{ +uint8_t addr[16 ]; + +/* Swap dest and src ipv6 addresses. */ +memcpy (&addr, &ipv6_hdr->src_addr,16 ); +memcpy (&ipv6_hdr->src_addr, &ipv6_hdr->dst_addr,16 ); +memcpy (&ipv6_hdr->dst_addr, &addr,16 ); +} + +static inline void +swap_tcp (struct rte_tcp_hdr *tcp_hdr) +{ +rte_be16_t port; + +/* Swap dest and src tcp port. */ + port = tcp_hdr->src_port; + tcp_hdr->src_port = tcp_hdr->dst_port; + tcp_hdr->dst_port = port; +} + +static inline void +swap_udp (struct rte_udp_hdr *udp_hdr) +{ +rte_be16_t port; + +/* Swap dest and src udp port */ + port = udp_hdr->src_port; + udp_hdr->src_port = udp_hdr->dst_port; + udp_hdr->dst_port = port; +} + +static inline void +do_5tswap (struct rte_mbuf *pkts_burst[],uint16_t nb_rx, +struct fwd_stream *fs) +{ +struct rte_port *txp; +struct rte_mbuf *mb; +uint16_t next_proto; +uint64_t ol_flags; +uint16_t proto; +int i; +union { +struct rte_ether_hdr *eth; +struct rte_vlan_hdr *vlan; +struct rte_ipv4_hdr *ipv4; +struct rte_ipv6_hdr *ipv6; +struct rte_tcp_hdr *tcp; +struct rte_udp_hdr *udp; +uint8_t *byte; + } h; + + txp = &ports[fs->tx_port]; + ol_flags =ol_flags_init (txp->dev_conf.txmode.offloads); +vlan_qinq_set (pkts_burst, nb_rx, ol_flags, + txp->tx_vlan_id, txp->tx_vlan_id_outer); +for (i =0 ; i < nb_rx; i++) { +if (likely (i < nb_rx -1 )) +rte_prefetch0 (rte_pktmbuf_mtod (pkts_burst[i+1 ], + void *)); + mb = pkts_burst[i]; + h.eth = rte_pktmbuf_mtod(mb, struct rte_ether_hdr *); + proto = h.eth->ether_type; +swap_mac (h.eth); + mb->l2_len =sizeof (struct rte_ether_hdr ); + h.eth++; +while (proto ==RTE_BE16 (RTE_ETHER_TYPE_VLAN ) || + proto ==RTE_BE16 (RTE_ETHER_TYPE_QINQ )) { + proto = h.vlan->eth_proto; + h.vlan++; + mb->l2_len +=sizeof (struct rte_vlan_hdr ); + } +if (proto ==RTE_BE16 (RTE_ETHER_TYPE_IPV4 )) { +swap_ipv4 (h.ipv4); + next_proto = h.ipv4->next_proto_id; + mb->l3_len =rte_ipv4_hdr_len (h.ipv4); + h.byte += mb->l3_len; + }else if (proto ==RTE_BE16 (RTE_ETHER_TYPE_IPV6 )) { +swap_ipv6 (h.ipv6); + next_proto = h.ipv6->proto; + h.ipv6++; + mb->l3_len =sizeof (struct rte_ipv6_hdr ); + }else { +mbuf_field_set (mb, ol_flags); +continue ; + } +if (next_proto ==IPPROTO_UDP ) { +swap_udp (h.udp); + mb->l4_len =sizeof (struct rte_udp_hdr ); + }else if (next_proto ==IPPROTO_TCP ) { +swap_tcp (h.tcp); + mb->l4_len = (h.tcp->data_off &0xf0 ) >>2 ; + } +mbuf_field_set (mb, ol_flags); + } +} + +#endif /* _5TSWAP_H_ */ app/test-pmd/macfwd.c +2
-31@@ -35,6 +35,7 @@#include <rte_flow.h> #include "testpmd.h" +#include "macfwd.h" /* * Forwarding of packets in MAC mode. @@ -45,13 +46,7 @@ static bool pkt_burst_mac_forward(struct fwd_stream *fs) {struct rte_mbuf *pkts_burst[MAX_PKT_BURST ]; -struct rte_port *txp; -struct rte_mbuf *mb; -struct rte_ether_hdr *eth_hdr;uint16_t nb_rx; -uint16_t i; -uint64_t ol_flags =0 ; -uint64_t tx_offloads;/* * Receive a burst of packets and forward them. @@ -60,31 +55,7 @@ pkt_burst_mac_forward(struct fwd_stream *fs)if (unlikely (nb_rx ==0 ))return false; - txp = &ports[fs->tx_port]; - tx_offloads = txp->dev_conf.txmode.offloads; -if (tx_offloads &RTE_ETH_TX_OFFLOAD_VLAN_INSERT ) - ol_flags =RTE_MBUF_F_TX_VLAN ; -if (tx_offloads &RTE_ETH_TX_OFFLOAD_QINQ_INSERT ) - ol_flags |=RTE_MBUF_F_TX_QINQ ; -if (tx_offloads &RTE_ETH_TX_OFFLOAD_MACSEC_INSERT ) - ol_flags |=RTE_MBUF_F_TX_MACSEC ; -for (i =0 ; i < nb_rx; i++) { -if (likely (i < nb_rx -1 )) -rte_prefetch0 (rte_pktmbuf_mtod (pkts_burst[i +1 ], - void *)); - mb = pkts_burst[i]; - eth_hdr = rte_pktmbuf_mtod(mb, struct rte_ether_hdr *); -rte_ether_addr_copy (&peer_eth_addrs[fs->peer_addr], - ð_hdr->dst_addr); -rte_ether_addr_copy (&ports[fs->tx_port].eth_addr, - ð_hdr->src_addr); - mb->ol_flags &=RTE_MBUF_F_INDIRECT |RTE_MBUF_F_EXTERNAL ; - mb->ol_flags |= ol_flags; - mb->l2_len =sizeof (struct rte_ether_hdr ); - mb->l3_len =sizeof (struct rte_ipv4_hdr ); - mb->vlan_tci = txp->tx_vlan_id; - mb->vlan_tci_outer = txp->tx_vlan_id_outer; - } +do_macfwd (pkts_burst, nb_rx, fs);common_fwd_stream_transmit (fs, pkts_burst, nb_rx);app/test-pmd/macfwd.h new file +0
-0
app/test-pmd/macfwd.h line 10
Quoted 10 lines
app/test-pmd/macfwd.h new file +10
-0@@ -0,0 +1,46 @@ +/* SPDX-License-Identifier: BSD-3-Clause +* Copyright(c) 2018 Intel Corporation +*/ + +#ifndef _MACFWD_H_ +#define _MACFWD_H_ + +static inline void +do_macfwd (struct rte_mbuf *pkts_burst[],uint16_t nb_rx, +struct fwd_stream *fs)
nit: indent/alignment is a little off here. There is some extra spaces. Same with other do_*()
app/test-pmd/macfwd.h line 19
Quoted 9 lines
app/test-pmd/macfwd.h new file +9
-0+{ +struct rte_ether_hdr *eth_hdr; +uint64_t ol_flags =0 ; +uint64_t tx_offloads; +struct rte_mbuf *mb; +struct rte_port *txp = &ports[fs->tx_port]; +uint16_t i; + +
can remove addition blank line
Quoted 51 lines
app/test-pmd/macfwd.h new file +27
-0+ tx_offloads = txp->dev_conf.txmode.offloads; +if (tx_offloads &RTE_ETH_TX_OFFLOAD_VLAN_INSERT ) + ol_flags =RTE_MBUF_F_TX_VLAN ; +if (tx_offloads &RTE_ETH_TX_OFFLOAD_QINQ_INSERT ) + ol_flags |=RTE_MBUF_F_TX_QINQ ; +if (tx_offloads &RTE_ETH_TX_OFFLOAD_MACSEC_INSERT ) + ol_flags |=RTE_MBUF_F_TX_MACSEC ; +for (i =0 ; i < nb_rx; i++) { +if (likely (i < nb_rx -1 )) +rte_prefetch0 (rte_pktmbuf_mtod (pkts_burst[i +1 ], + void *)); + mb = pkts_burst[i]; + eth_hdr = rte_pktmbuf_mtod(mb, struct rte_ether_hdr *); +rte_ether_addr_copy (&peer_eth_addrs[fs->peer_addr], + ð_hdr->dst_addr); +rte_ether_addr_copy (&ports[fs->tx_port].eth_addr, + ð_hdr->src_addr); + mb->ol_flags &=RTE_MBUF_F_INDIRECT |RTE_MBUF_F_EXTERNAL ; + mb->ol_flags |= ol_flags; + mb->l2_len =sizeof (struct rte_ether_hdr ); + mb->l3_len =sizeof (struct rte_ipv4_hdr ); + mb->vlan_tci = txp->tx_vlan_id; + mb->vlan_tci_outer = txp->tx_vlan_id_outer; + } +} + +#endif /* _MACFWD_H_ */ app/test-pmd/noisy_vnf.c +12
-0@@ -32,6 +32,18 @@#include <rte_malloc.h> #include "testpmd.h" +#include "5tswap.h" +#include "macfwd.h" +#if defined(RTE_ARCH_X86 ) +#include "macswap_sse.h" +#elif defined(__ARM_NEON) +#include "macswap_neon.h" +#else +#include "macswap.h" +#endif + +#define NOISY_STRSIZE 256 +#define NOISY_RING "noisy_ring_%d\n"struct noisy_config {struct rte_ring *f;
app/test-pmd/noisy_vnf.c sim_memory_lookups(struct noisy_config *ncf, uint16_t nb_pkts) · line 85
Quoted 6 lines
app/test-pmd/noisy_vnf.c +0
-3@@ -80,9 +92,6 @@ sim_memory_lookups(struct noisy_config *ncf, uint16_t nb_pkts) {uint16_t i, j; -if (!ncf->do_sim) -return ; -
Why is this removed? It's not checked before all calls to this function
Quoted 56 lines
app/test-pmd/noisy_vnf.c +17
-6for (i =0 ; i < nb_pkts; i++) {for (j =0 ; j < noisy_lkup_num_writes; j++)do_write (ncf->vnf_mem);@@ -110,15 +119,13 @@ sim_memory_lookups(struct noisy_config *ncf, uint16_t nb_pkts)* out of the FIFO * 4. Cases 2 and 3 combined */ -static bool -pkt_burst_noisy_vnf (struct fwd_stream *fs) +static uint16_t +noisy_eth_tx_burst (struct fwd_stream *fs,uint16_t nb_rx,struct rte_mbuf **pkts_burst) {const uint64_t freq_khz =rte_get_timer_hz () /1000 ;struct noisy_config *ncf = noisy_cfg[fs->rx_port]; -struct rte_mbuf *pkts_burst[MAX_PKT_BURST ];struct rte_mbuf *tmp_pkts[MAX_PKT_BURST ];uint16_t nb_deqd =0 ; -uint16_t nb_rx =0 ;uint16_t nb_tx =0 ;uint16_t nb_enqd;unsigned int fifo_free;@@ -126,12 +133,12 @@ pkt_burst_noisy_vnf(struct fwd_stream *fs)bool needs_flush = false;uint64_t now; - nb_rx =common_fwd_stream_receive (fs, pkts_burst, nb_pkt_per_burst);if (unlikely (nb_rx ==0 )) goto flush;if (!ncf->do_buffering) { -sim_memory_lookups (ncf, nb_rx); +if (ncf->do_sim) +sim_memory_lookups (ncf, nb_rx); nb_tx =common_fwd_stream_transmit (fs, pkts_burst, nb_rx); goto end; }@@ -169,11 +176,61 @@ pkt_burst_noisy_vnf(struct fwd_stream *fs) ncf->prev_time =rte_get_timer_cycles (); } end: +return nb_tx; +} + +static bool +pkt_burst_io (struct fwd_stream *fs) +{ +struct rte_mbuf *pkts_burst[MAX_PKT_BURST ]; +uint16_t nb_rx; +uint16_t nb_tx; + + nb_rx =common_fwd_stream_receive (fs, pkts_burst, nb_pkt_per_burst); + nb_tx =noisy_eth_tx_burst (fs, nb_rx, pkts_burst); +return nb_rx >0 || nb_tx >0 ; }
app/test-pmd/noisy_vnf.c pkt_burst_noisy_vnf(struct fwd_stream *fs) · line 202
Quoted 10 lines
app/test-pmd/noisy_vnf.c +8
-2-#define NOISY_STRSIZE 256 -#define NOISY_RING "noisy_ring_%d\n" +static bool +pkt_burst_mac (struct fwd_stream *fs) +{ +struct rte_mbuf *pkts_burst[MAX_PKT_BURST ]; +uint16_t nb_rx; +uint16_t nb_tx; + + nb_rx =common_fwd_stream_receive (fs, pkts_burst, nb_pkt_per_burst);
Similar to macfwd.c, you can add check for unlikely(nb_rx == 0) at this point in these fns.
app/test-pmd/noisy_vnf.c pkt_burst_noisy_vnf(struct fwd_stream *fs) · line 213
Quoted 11 lines
app/test-pmd/noisy_vnf.c +11
-0+do_macfwd (pkts_burst, nb_rx, fs); + nb_tx =noisy_eth_tx_burst (fs, nb_rx, pkts_burst); + +return nb_rx >0 || nb_tx >0 ; +} +static bool +pkt_burst_macswap (struct fwd_stream *fs) +{ +struct rte_mbuf *pkts_burst[MAX_PKT_BURST ]; +uint16_t nb_rx =0 ; +uint16_t nb_tx =0 ;
nit: these are not assigned in the other functions
Quoted 75 lines
app/test-pmd/noisy_vnf.c +31
-2+ + nb_rx =common_fwd_stream_receive (fs, pkts_burst, nb_pkt_per_burst); +do_macswap (pkts_burst, nb_rx, &ports[fs->tx_port]); + nb_tx =noisy_eth_tx_burst (fs, nb_rx, pkts_burst); + +return nb_rx >0 || nb_tx >0 ; +} +static bool +pkt_brust_5tswap (struct fwd_stream *fs) +{ +struct rte_mbuf *pkts_burst[MAX_PKT_BURST ]; +uint16_t nb_rx =0 ; +uint16_t nb_tx =0 ; + + nb_rx =common_fwd_stream_receive (fs, pkts_burst, nb_pkt_per_burst); +do_5tswap (pkts_burst, nb_rx, fs); + nb_tx =noisy_eth_tx_burst (fs, nb_rx, pkts_burst); + +return nb_rx >0 || nb_tx >0 ; +}static void noisy_fwd_end (portid_t pi)@@ -226,6 +283,15 @@ noisy_fwd_begin(portid_t pi) "--noisy-lkup-memory-size must be > 0\n"); } +if (noisy_fwd_mode ==NOISY_FWD_MODE_IO ) + noisy_vnf_engine.packet_fwd = pkt_burst_io; +else if (noisy_fwd_mode ==NOISY_FWD_MODE_MAC ) + noisy_vnf_engine.packet_fwd = pkt_burst_mac; +else if (noisy_fwd_mode ==NOISY_FWD_MODE_MACSWAP ) + noisy_vnf_engine.packet_fwd = pkt_burst_macswap; +else if (noisy_fwd_mode ==NOISY_FWD_MODE_5TSWAP ) + noisy_vnf_engine.packet_fwd = pkt_brust_5tswap; +return 0 ; }@@ -233,6 +299,6 @@ struct fwd_engine noisy_vnf_engine = { .fwd_mode_name = "noisy", .port_fwd_begin = noisy_fwd_begin, .port_fwd_end = noisy_fwd_end, - .stream_init = common_fwd_stream_init, - .packet_fwd = pkt_burst_noisy_vnf, + .stream_init = common_fwd_stream_init, + .packet_fwd = pkt_burst_io, };app/test-pmd/parameters.c +5
-0@@ -196,6 +196,7 @@ usage(char* progname)printf (" --noisy-lkup-num-writes=N: do N random writes per packet\n" );printf (" --noisy-lkup-num-reads=N: do N random reads per packet\n" );printf (" --noisy-lkup-num-reads-writes=N: do N random reads and writes per packet\n" ); +printf (" --noisy-fwd-mode=mode: set the fwd mode\n" );printf (" --no-iova-contig: mempool memory can be IOVA non contiguous. " "valid only with --mp-alloc=anon\n" ); printf(" --rx-mq-mode=0xX: hexadecimal bitmask of RX mq mode can be "@@ -704,6 +705,7 @@ launch_args_parse(int argc, char** argv) { "noisy-lkup-num-writes", 1, 0, 0 }, { "noisy-lkup-num-reads", 1, 0, 0 }, { "noisy-lkup-num-reads-writes", 1, 0, 0 }, + { "noisy-fwd-mode", 1, 0, 0 }, { "no-iova-contig", 0, 0, 0 }, { "rx-mq-mode", 1, 0, 0 }, { "record-core-cycles", 0, 0, 0 },@@ -1444,6 +1446,21 @@ launch_args_parse(int argc, char** argv)rte_exit (EXIT_FAILURE ,"noisy-lkup-num-reads-writes must be >= 0\n" ); } +if (!strcmp (lgopts[opt_idx].name, +"noisy-fwd-mode" )) { +if (!strcmp (optarg,"io" ))
app/test-pmd/parameters.c launch_args_parse(int argc, char** argv) · line 1461
Quoted 10 lines
app/test-pmd/parameters.c +10
-0+ noisy_fwd_mode =NOISY_FWD_MODE_IO ; + else if (!strcmp(optarg, "mac")) + noisy_fwd_mode =NOISY_FWD_MODE_MAC ; + else if (!strcmp(optarg, "macswap")) + noisy_fwd_mode =NOISY_FWD_MODE_MACSWAP ; + else if (!strcmp(optarg, "5tswap")) + noisy_fwd_mode =NOISY_FWD_MODE_5TSWAP ; + else + rte_exit(EXIT_FAILURE, "noisy-fwd-mode %s invalid -" + " must b a valid fwd mode\n",
typo "be"
I would specify "..must be a valid noisy-fwd-mode value" to avoid confusion with the full set of general fwd modes and easier for user to search them in docs.
Quoted 67 lines
app/test-pmd/parameters.c +2
-0+ optarg); + }if (!strcmp (lgopts[opt_idx].name,"no-iova-contig" )) mempool_flags =RTE_MEMPOOL_F_NO_IOVA_CONTIG ;app/test-pmd/testpmd.c +5
-0@@ -364,6 +364,11 @@ uint64_t noisy_lkup_num_reads;*/ uint64_t noisy_lkup_num_reads_writes; +/* +* Configurable forwarding mode in VNF simulation. +*/ +int noisy_fwd_mode; +/* * Receive Side Scaling (RSS) configuration. */ app/test-pmd/testpmd.h +8
-0@@ -116,6 +116,13 @@ enum { QUEUE_JOB_TYPE_ACTION_QUERY, }; +enum { +NOISY_FWD_MODE_IO , +NOISY_FWD_MODE_MAC , +NOISY_FWD_MODE_MACSWAP , +NOISY_FWD_MODE_5TSWAP +}; +/** * The data structure associated with RX and TX packet burst statistics * that are recorded for each forwarding stream. @@ -561,6 +568,7 @@ extern uint64_t noisy_lkup_mem_sz;extern uint64_t noisy_lkup_num_writes;extern uint64_t noisy_lkup_num_reads;extern uint64_t noisy_lkup_num_reads_writes; +extern int noisy_fwd_mode;extern uint8_t dcb_config;doc/guides/testpmd_app_ug/run_app.rst +9
-0@@ -519,6 +519,15 @@ The command line options are: Set the number of r/w accesses to be done in noisy neighbor simulation memory buffer to N. Only available with the noisy forwarding mode. The default value is 0. +* ``--noisy-fwd-mode=mode`` + + Set the noisy vnf forwarding mode where ``mode`` is one of the following:: + + io (the default) + mac + macswap + 5tswap + * ``--no-iova-contig`` Enable to create mempool which is not IOVA contiguous. Valid only with --mp-alloc=anon.
Quoted 19 lines · Kevin Traynor
Quoted 8 lines · Mike Pattrick
Previously the noisy neighbour vnf simulation would only operate in io mode, forwarding packets as is. However, this limited the usefulness of noisy neighbour simulation.
This feature has now been expanded to supporting mac, macswap, and 5tswap modes. To facilitate adding this support, some new header files were added.
Hi Mike,
I think it makes sense to allow these functionalities to be combined. It does seem like that noisy neighbour shouldn't have been added as a standalone fowarding option in the first place, as it's not mutually exclusive with the other fwding modes. Now it's forcing a user to set a fwding mode within a fwding mode to combine the functionality :/
Quoted 4 lines
The approach is to allow the fwding modes to expose their forwarding method so noisy can call them. Did you consider to expose the noisy functionality and allow the other forwarding modes to call that when the --noisy-* flags are set?
Personally I like this approach more, and that was the strategy I took with the previous version. However, that change didn't seem popular at the time.
http://patches.dpdk.org/project/dpdk/patch/[email protected]/#157095
Quoted 534 lines
For example, a user sets fwding mode as normal 'fwd=macfwd' but then if the user adds the --noisy-* params, the macfwd'ing mode calls some functions exposed to add the noise, which seems a bit more intuitive.
Also, if someone adds a new fwding mode, they can just call the noisy functions and don't have update noisy fwding mode to add the new mode.
I'm not sure if it's better, just throwing it out there as an alternative idea.
On the downside, it would break backwards compatibility because previously those --noisy-* params would have had no effect with say macfwd mode, but now they will. So maybe that's enough to prohibit it.
In the past, I would have had all the params set and just changed fwdmode to enable/disable noisy vnf. That would behaviour would now be changed with this approach.
What do you think?
Few comments on the code below.
thanks,
Kevin.Quoted 150 lines
Signed-off-by Mike Pattrick <[email protected]>---
v2: Reverted changes to random memory lookup
v3: Refactored entire patch--- app/test-pmd/5tswap.c | 118 +---------------------- app/test-pmd/5tswap.h | 130 ++++++++++++++++++++++++++ app/test-pmd/macfwd.c | 33 +------ app/test-pmd/macfwd.h | 46 +++++++++ app/test-pmd/noisy_vnf.c | 92 +++++++++++++++--- app/test-pmd/parameters.c | 17 ++++ app/test-pmd/testpmd.c | 5 + app/test-pmd/testpmd.h | 8 ++ doc/guides/testpmd_app_ug/run_app.rst | 9 ++ 9 files changed, 299 insertions(+), 159 deletions(-)create mode 100644
app/test-pmd/5tswap.h
create mode 100644app/test-pmd/macfwd.happ/test-pmd/5tswap.c +1
-107@@ -17,64 +17,8 @@#include <rte_ip.h> #include <rte_flow.h> -#include "macswap_common.h" #include "testpmd.h" - - -static inline void -swap_mac (struct rte_ether_hdr *eth_hdr) -{ -struct rte_ether_addr addr; - -/* Swap dest and src mac addresses. */ -rte_ether_addr_copy (ð_hdr->dst_addr, &addr); -rte_ether_addr_copy (ð_hdr->src_addr, ð_hdr->dst_addr); -rte_ether_addr_copy (&addr, ð_hdr->src_addr); -} - -static inline void -swap_ipv4 (struct rte_ipv4_hdr *ipv4_hdr) -{ -rte_be32_t addr; - -/* Swap dest and src ipv4 addresses. */ - addr = ipv4_hdr->src_addr; - ipv4_hdr->src_addr = ipv4_hdr->dst_addr; - ipv4_hdr->dst_addr = addr; -} - -static inline void -swap_ipv6 (struct rte_ipv6_hdr *ipv6_hdr) -{ -uint8_t addr[16 ]; - -/* Swap dest and src ipv6 addresses. */ -memcpy (&addr, &ipv6_hdr->src_addr,16 ); -memcpy (&ipv6_hdr->src_addr, &ipv6_hdr->dst_addr,16 ); -memcpy (&ipv6_hdr->dst_addr, &addr,16 ); -} - -static inline void -swap_tcp (struct rte_tcp_hdr *tcp_hdr) -{ -rte_be16_t port; - -/* Swap dest and src tcp port. */ - port = tcp_hdr->src_port; - tcp_hdr->src_port = tcp_hdr->dst_port; - tcp_hdr->dst_port = port; -} - -static inline void -swap_udp (struct rte_udp_hdr *udp_hdr) -{ -rte_be16_t port; - -/* Swap dest and src udp port */ - port = udp_hdr->src_port; - udp_hdr->src_port = udp_hdr->dst_port; - udp_hdr->dst_port = port; -} +#include "5tswap.h" /* * 5 tuple swap forwarding mode: Swap the source and the destination of layers @@ -85,22 +29,7 @@ static bool pkt_burst_5tuple_swap(struct fwd_stream *fs) {struct rte_mbuf *pkts_burst[MAX_PKT_BURST ]; -struct rte_port *txp; -struct rte_mbuf *mb; -uint16_t next_proto; -uint64_t ol_flags; -uint16_t proto;uint16_t nb_rx; -int i; -union { -struct rte_ether_hdr *eth; -struct rte_vlan_hdr *vlan; -struct rte_ipv4_hdr *ipv4; -struct rte_ipv6_hdr *ipv6; -struct rte_tcp_hdr *tcp; -struct rte_udp_hdr *udp; -uint8_t *byte; - } h;/* * Receive a burst of packets and forward them. @@ -109,49 +38,8 @@ pkt_burst_5tuple_swap(struct fwd_stream *fs)if (unlikely (nb_rx ==0 ))return false; - txp = &ports[fs->tx_port]; - ol_flags =ol_flags_init (txp->dev_conf.txmode.offloads); -vlan_qinq_set (pkts_burst, nb_rx, ol_flags, - txp->tx_vlan_id, txp->tx_vlan_id_outer); -for (i =0 ; i < nb_rx; i++) { -if (likely (i < nb_rx -1 )) -rte_prefetch0 (rte_pktmbuf_mtod (pkts_burst[i+1 ], - void *)); - mb = pkts_burst[i]; - h.eth = rte_pktmbuf_mtod(mb, struct rte_ether_hdr *); - proto = h.eth->ether_type; -swap_mac (h.eth); - mb->l2_len =sizeof (struct rte_ether_hdr ); - h.eth++; -while (proto ==RTE_BE16 (RTE_ETHER_TYPE_VLAN ) || - proto ==RTE_BE16 (RTE_ETHER_TYPE_QINQ )) { - proto = h.vlan->eth_proto; - h.vlan++; - mb->l2_len +=sizeof (struct rte_vlan_hdr ); - } -if (proto ==RTE_BE16 (RTE_ETHER_TYPE_IPV4 )) { -swap_ipv4 (h.ipv4); - next_proto = h.ipv4->next_proto_id; - mb->l3_len =rte_ipv4_hdr_len (h.ipv4); - h.byte += mb->l3_len; - }else if (proto ==RTE_BE16 (RTE_ETHER_TYPE_IPV6 )) { -swap_ipv6 (h.ipv6); - next_proto = h.ipv6->proto; - h.ipv6++; - mb->l3_len =sizeof (struct rte_ipv6_hdr ); - }else { -mbuf_field_set (mb, ol_flags); -continue ; - } -if (next_proto ==IPPROTO_UDP ) {app/test-pmd/5tswap.c pkt_burst_5tuple_swap(struct fwd_stream *fs) · line 42
Quoted 10 lines
app/test-pmd/5tswap.c +2
-8-swap_udp (h.udp); - mb->l4_len =sizeof (struct rte_udp_hdr ); - }else if (next_proto ==IPPROTO_TCP ) { -swap_tcp (h.tcp); - mb->l4_len = (h.tcp->data_off &0xf0 ) >>2 ; - } -mbuf_field_set (mb, ol_flags); - } +do_5tswap (pkts_burst, nb_rx, fs); +this simplification is nice.
Quoted 204 lines
app/test-pmd/5tswap.c +0
-0common_fwd_stream_transmit (fs, pkts_burst, nb_rx);return true;app/test-pmd/5tswap.h new file +130
-0@@ -0,0 +1,130 @@ +/* SPDX-License-Identifier: BSD-3-Clause +* Copyright(c) 2018 Intel Corporation +*/ + +#ifndef _5TSWAP_H_ +#define _5TSWAP_H_ + +#include "macswap_common.h" + +static inline void +swap_mac (struct rte_ether_hdr *eth_hdr) +{ +struct rte_ether_addr addr; + +/* Swap dest and src mac addresses. */ +rte_ether_addr_copy (ð_hdr->dst_addr, &addr); +rte_ether_addr_copy (ð_hdr->src_addr, ð_hdr->dst_addr); +rte_ether_addr_copy (&addr, ð_hdr->src_addr); +} + +static inline void +swap_ipv4 (struct rte_ipv4_hdr *ipv4_hdr) +{ +rte_be32_t addr; + +/* Swap dest and src ipv4 addresses. */ + addr = ipv4_hdr->src_addr; + ipv4_hdr->src_addr = ipv4_hdr->dst_addr; + ipv4_hdr->dst_addr = addr; +} + +static inline void +swap_ipv6 (struct rte_ipv6_hdr *ipv6_hdr) +{ +uint8_t addr[16 ]; + +/* Swap dest and src ipv6 addresses. */ +memcpy (&addr, &ipv6_hdr->src_addr,16 ); +memcpy (&ipv6_hdr->src_addr, &ipv6_hdr->dst_addr,16 ); +memcpy (&ipv6_hdr->dst_addr, &addr,16 ); +} + +static inline void +swap_tcp (struct rte_tcp_hdr *tcp_hdr) +{ +rte_be16_t port; + +/* Swap dest and src tcp port. */ + port = tcp_hdr->src_port; + tcp_hdr->src_port = tcp_hdr->dst_port; + tcp_hdr->dst_port = port; +} + +static inline void +swap_udp (struct rte_udp_hdr *udp_hdr) +{ +rte_be16_t port; + +/* Swap dest and src udp port */ + port = udp_hdr->src_port; + udp_hdr->src_port = udp_hdr->dst_port; + udp_hdr->dst_port = port; +} + +static inline void +do_5tswap (struct rte_mbuf *pkts_burst[],uint16_t nb_rx, +struct fwd_stream *fs) +{ +struct rte_port *txp; +struct rte_mbuf *mb; +uint16_t next_proto; +uint64_t ol_flags; +uint16_t proto; +int i; +union { +struct rte_ether_hdr *eth; +struct rte_vlan_hdr *vlan; +struct rte_ipv4_hdr *ipv4; +struct rte_ipv6_hdr *ipv6; +struct rte_tcp_hdr *tcp; +struct rte_udp_hdr *udp; +uint8_t *byte; + } h; + + txp = &ports[fs->tx_port]; + ol_flags =ol_flags_init (txp->dev_conf.txmode.offloads); +vlan_qinq_set (pkts_burst, nb_rx, ol_flags, + txp->tx_vlan_id, txp->tx_vlan_id_outer); +for (i =0 ; i < nb_rx; i++) { +if (likely (i < nb_rx -1 )) +rte_prefetch0 (rte_pktmbuf_mtod (pkts_burst[i+1 ], + void *)); + mb = pkts_burst[i]; + h.eth = rte_pktmbuf_mtod(mb, struct rte_ether_hdr *); + proto = h.eth->ether_type; +swap_mac (h.eth); + mb->l2_len =sizeof (struct rte_ether_hdr ); + h.eth++; +while (proto ==RTE_BE16 (RTE_ETHER_TYPE_VLAN ) || + proto ==RTE_BE16 (RTE_ETHER_TYPE_QINQ )) { + proto = h.vlan->eth_proto; + h.vlan++; + mb->l2_len +=sizeof (struct rte_vlan_hdr ); + } +if (proto ==RTE_BE16 (RTE_ETHER_TYPE_IPV4 )) { +swap_ipv4 (h.ipv4); + next_proto = h.ipv4->next_proto_id; + mb->l3_len =rte_ipv4_hdr_len (h.ipv4); + h.byte += mb->l3_len; + }else if (proto ==RTE_BE16 (RTE_ETHER_TYPE_IPV6 )) { +swap_ipv6 (h.ipv6); + next_proto = h.ipv6->proto; + h.ipv6++; + mb->l3_len =sizeof (struct rte_ipv6_hdr ); + }else { +mbuf_field_set (mb, ol_flags); +continue ; + } +if (next_proto ==IPPROTO_UDP ) { +swap_udp (h.udp); + mb->l4_len =sizeof (struct rte_udp_hdr ); + }else if (next_proto ==IPPROTO_TCP ) { +swap_tcp (h.tcp); + mb->l4_len = (h.tcp->data_off &0xf0 ) >>2 ; + } +mbuf_field_set (mb, ol_flags); + } +} + +#endif /* _5TSWAP_H_ */ app/test-pmd/macfwd.c +2
-31@@ -35,6 +35,7 @@#include <rte_flow.h> #include "testpmd.h" +#include "macfwd.h" /* * Forwarding of packets in MAC mode. @@ -45,13 +46,7 @@ static bool pkt_burst_mac_forward(struct fwd_stream *fs) {struct rte_mbuf *pkts_burst[MAX_PKT_BURST ]; -struct rte_port *txp; -struct rte_mbuf *mb; -struct rte_ether_hdr *eth_hdr;uint16_t nb_rx; -uint16_t i; -uint64_t ol_flags =0 ; -uint64_t tx_offloads;/* * Receive a burst of packets and forward them. @@ -60,31 +55,7 @@ pkt_burst_mac_forward(struct fwd_stream *fs)if (unlikely (nb_rx ==0 ))return false; - txp = &ports[fs->tx_port]; - tx_offloads = txp->dev_conf.txmode.offloads; -if (tx_offloads &RTE_ETH_TX_OFFLOAD_VLAN_INSERT ) - ol_flags =RTE_MBUF_F_TX_VLAN ; -if (tx_offloads &RTE_ETH_TX_OFFLOAD_QINQ_INSERT ) - ol_flags |=RTE_MBUF_F_TX_QINQ ; -if (tx_offloads &RTE_ETH_TX_OFFLOAD_MACSEC_INSERT ) - ol_flags |=RTE_MBUF_F_TX_MACSEC ; -for (i =0 ; i < nb_rx; i++) { -if (likely (i < nb_rx -1 )) -rte_prefetch0 (rte_pktmbuf_mtod (pkts_burst[i +1 ], - void *)); - mb = pkts_burst[i]; - eth_hdr = rte_pktmbuf_mtod(mb, struct rte_ether_hdr *); -rte_ether_addr_copy (&peer_eth_addrs[fs->peer_addr], - ð_hdr->dst_addr); -rte_ether_addr_copy (&ports[fs->tx_port].eth_addr, - ð_hdr->src_addr); - mb->ol_flags &=RTE_MBUF_F_INDIRECT |RTE_MBUF_F_EXTERNAL ; - mb->ol_flags |= ol_flags; - mb->l2_len =sizeof (struct rte_ether_hdr ); - mb->l3_len =sizeof (struct rte_ipv4_hdr ); - mb->vlan_tci = txp->tx_vlan_id; - mb->vlan_tci_outer = txp->tx_vlan_id_outer; - } +do_macfwd (pkts_burst, nb_rx, fs);common_fwd_stream_transmit (fs, pkts_burst, nb_rx);app/test-pmd/macfwd.h new file +0
-0app/test-pmd/macfwd.h line 10
Quoted 10 lines
app/test-pmd/macfwd.h new file +10
-0@@ -0,0 +1,46 @@ +/* SPDX-License-Identifier: BSD-3-Clause +* Copyright(c) 2018 Intel Corporation +*/ + +#ifndef _MACFWD_H_ +#define _MACFWD_H_ + +static inline void +do_macfwd (struct rte_mbuf *pkts_burst[],uint16_t nb_rx, +struct fwd_stream *fs)nit: indent/alignment is a little off here. There is some extra spaces. Same with other do_*()
app/test-pmd/macfwd.h line 19
Quoted 9 lines
app/test-pmd/macfwd.h new file +9
-0+{ +struct rte_ether_hdr *eth_hdr; +uint64_t ol_flags =0 ; +uint64_t tx_offloads; +struct rte_mbuf *mb; +struct rte_port *txp = &ports[fs->tx_port]; +uint16_t i; + +can remove addition blank line
Quoted 51 lines
app/test-pmd/macfwd.h new file +27
-0+ tx_offloads = txp->dev_conf.txmode.offloads; +if (tx_offloads &RTE_ETH_TX_OFFLOAD_VLAN_INSERT ) + ol_flags =RTE_MBUF_F_TX_VLAN ; +if (tx_offloads &RTE_ETH_TX_OFFLOAD_QINQ_INSERT ) + ol_flags |=RTE_MBUF_F_TX_QINQ ; +if (tx_offloads &RTE_ETH_TX_OFFLOAD_MACSEC_INSERT ) + ol_flags |=RTE_MBUF_F_TX_MACSEC ; +for (i =0 ; i < nb_rx; i++) { +if (likely (i < nb_rx -1 )) +rte_prefetch0 (rte_pktmbuf_mtod (pkts_burst[i +1 ], + void *)); + mb = pkts_burst[i]; + eth_hdr = rte_pktmbuf_mtod(mb, struct rte_ether_hdr *); +rte_ether_addr_copy (&peer_eth_addrs[fs->peer_addr], + ð_hdr->dst_addr); +rte_ether_addr_copy (&ports[fs->tx_port].eth_addr, + ð_hdr->src_addr); + mb->ol_flags &=RTE_MBUF_F_INDIRECT |RTE_MBUF_F_EXTERNAL ; + mb->ol_flags |= ol_flags; + mb->l2_len =sizeof (struct rte_ether_hdr ); + mb->l3_len =sizeof (struct rte_ipv4_hdr ); + mb->vlan_tci = txp->tx_vlan_id; + mb->vlan_tci_outer = txp->tx_vlan_id_outer; + } +} + +#endif /* _MACFWD_H_ */ app/test-pmd/noisy_vnf.c +12
-0@@ -32,6 +32,18 @@#include <rte_malloc.h> #include "testpmd.h" +#include "5tswap.h" +#include "macfwd.h" +#if defined(RTE_ARCH_X86 ) +#include "macswap_sse.h" +#elif defined(__ARM_NEON) +#include "macswap_neon.h" +#else +#include "macswap.h" +#endif + +#define NOISY_STRSIZE 256 +#define NOISY_RING "noisy_ring_%d\n"struct noisy_config {struct rte_ring *f;app/test-pmd/noisy_vnf.c sim_memory_lookups(struct noisy_config *ncf, uint16_t nb_pkts) · line 85
Quoted 6 lines
app/test-pmd/noisy_vnf.c +0
-3@@ -80,9 +92,6 @@ sim_memory_lookups(struct noisy_config *ncf, uint16_t nb_pkts) {uint16_t i, j; -if (!ncf->do_sim) -return ; -Why is this removed? It's not checked before all calls to this function
Quoted 56 lines
app/test-pmd/noisy_vnf.c +17
-6for (i =0 ; i < nb_pkts; i++) {for (j =0 ; j < noisy_lkup_num_writes; j++)do_write (ncf->vnf_mem);@@ -110,15 +119,13 @@ sim_memory_lookups(struct noisy_config *ncf, uint16_t nb_pkts)* out of the FIFO * 4. Cases 2 and 3 combined */ -static bool -pkt_burst_noisy_vnf (struct fwd_stream *fs) +static uint16_t +noisy_eth_tx_burst (struct fwd_stream *fs,uint16_t nb_rx,struct rte_mbuf **pkts_burst) {const uint64_t freq_khz =rte_get_timer_hz () /1000 ;struct noisy_config *ncf = noisy_cfg[fs->rx_port]; -struct rte_mbuf *pkts_burst[MAX_PKT_BURST ];struct rte_mbuf *tmp_pkts[MAX_PKT_BURST ];uint16_t nb_deqd =0 ; -uint16_t nb_rx =0 ;uint16_t nb_tx =0 ;uint16_t nb_enqd;unsigned int fifo_free;@@ -126,12 +133,12 @@ pkt_burst_noisy_vnf(struct fwd_stream *fs)bool needs_flush = false;uint64_t now; - nb_rx =common_fwd_stream_receive (fs, pkts_burst, nb_pkt_per_burst);if (unlikely (nb_rx ==0 )) goto flush;if (!ncf->do_buffering) { -sim_memory_lookups (ncf, nb_rx); +if (ncf->do_sim) +sim_memory_lookups (ncf, nb_rx); nb_tx =common_fwd_stream_transmit (fs, pkts_burst, nb_rx); goto end; }@@ -169,11 +176,61 @@ pkt_burst_noisy_vnf(struct fwd_stream *fs) ncf->prev_time =rte_get_timer_cycles (); } end: +return nb_tx; +} + +static bool +pkt_burst_io (struct fwd_stream *fs) +{ +struct rte_mbuf *pkts_burst[MAX_PKT_BURST ]; +uint16_t nb_rx; +uint16_t nb_tx; + + nb_rx =common_fwd_stream_receive (fs, pkts_burst, nb_pkt_per_burst); + nb_tx =noisy_eth_tx_burst (fs, nb_rx, pkts_burst); +return nb_rx >0 || nb_tx >0 ; }
Quoted 13 lines
app/test-pmd/noisy_vnf.c pkt_burst_noisy_vnf(struct fwd_stream *fs) · line 202
Quoted 10 lines
app/test-pmd/noisy_vnf.c +8
-2-#define NOISY_STRSIZE 256 -#define NOISY_RING "noisy_ring_%d\n" +static bool +pkt_burst_mac (struct fwd_stream *fs) +{ +struct rte_mbuf *pkts_burst[MAX_PKT_BURST ]; +uint16_t nb_rx; +uint16_t nb_tx; + + nb_rx =common_fwd_stream_receive (fs, pkts_burst, nb_pkt_per_burst);Similar to
macfwd.c, you can add check forunlikely(nb_rx == 0)at this point in these fns.
That's true. I removed it because I'll have to call noisy_eth_tx_burst() regardless, but we could avoid the middle call in these locations.
I agree with the other suggestions.
Thanks,
M
Quoted 175 lines
app/test-pmd/noisy_vnf.c pkt_burst_noisy_vnf(struct fwd_stream *fs) · line 213
Quoted 12 lines
app/test-pmd/noisy_vnf.c +11
-0+do_macfwd (pkts_burst, nb_rx, fs); + nb_tx =noisy_eth_tx_burst (fs, nb_rx, pkts_burst); + +return nb_rx >0 || nb_tx >0 ; +} +static bool +pkt_burst_macswap (struct fwd_stream *fs) +{ +struct rte_mbuf *pkts_burst[MAX_PKT_BURST ]; +uint16_t nb_rx =0 ; +uint16_t nb_tx =0 ;nit: these are not assigned in the other functions
Quoted 75 lines
app/test-pmd/noisy_vnf.c +31
-2+ + nb_rx =common_fwd_stream_receive (fs, pkts_burst, nb_pkt_per_burst); +do_macswap (pkts_burst, nb_rx, &ports[fs->tx_port]); + nb_tx =noisy_eth_tx_burst (fs, nb_rx, pkts_burst); + +return nb_rx >0 || nb_tx >0 ; +} +static bool +pkt_brust_5tswap (struct fwd_stream *fs) +{ +struct rte_mbuf *pkts_burst[MAX_PKT_BURST ]; +uint16_t nb_rx =0 ; +uint16_t nb_tx =0 ; + + nb_rx =common_fwd_stream_receive (fs, pkts_burst, nb_pkt_per_burst); +do_5tswap (pkts_burst, nb_rx, fs); + nb_tx =noisy_eth_tx_burst (fs, nb_rx, pkts_burst); + +return nb_rx >0 || nb_tx >0 ; +}static void noisy_fwd_end (portid_t pi)@@ -226,6 +283,15 @@ noisy_fwd_begin(portid_t pi) "--noisy-lkup-memory-size must be > 0\n"); } +if (noisy_fwd_mode ==NOISY_FWD_MODE_IO ) + noisy_vnf_engine.packet_fwd = pkt_burst_io; +else if (noisy_fwd_mode ==NOISY_FWD_MODE_MAC ) + noisy_vnf_engine.packet_fwd = pkt_burst_mac; +else if (noisy_fwd_mode ==NOISY_FWD_MODE_MACSWAP ) + noisy_vnf_engine.packet_fwd = pkt_burst_macswap; +else if (noisy_fwd_mode ==NOISY_FWD_MODE_5TSWAP ) + noisy_vnf_engine.packet_fwd = pkt_brust_5tswap; +return 0 ; }@@ -233,6 +299,6 @@ struct fwd_engine noisy_vnf_engine = { .fwd_mode_name = "noisy", .port_fwd_begin = noisy_fwd_begin, .port_fwd_end = noisy_fwd_end, - .stream_init = common_fwd_stream_init, - .packet_fwd = pkt_burst_noisy_vnf, + .stream_init = common_fwd_stream_init, + .packet_fwd = pkt_burst_io, };app/test-pmd/parameters.c +5
-0@@ -196,6 +196,7 @@ usage(char* progname)printf (" --noisy-lkup-num-writes=N: do N random writes per packet\n" );printf (" --noisy-lkup-num-reads=N: do N random reads per packet\n" );printf (" --noisy-lkup-num-reads-writes=N: do N random reads and writes per packet\n" ); +printf (" --noisy-fwd-mode=mode: set the fwd mode\n" );printf (" --no-iova-contig: mempool memory can be IOVA non contiguous. " "valid only with --mp-alloc=anon\n" ); printf(" --rx-mq-mode=0xX: hexadecimal bitmask of RX mq mode can be "@@ -704,6 +705,7 @@ launch_args_parse(int argc, char** argv) { "noisy-lkup-num-writes", 1, 0, 0 }, { "noisy-lkup-num-reads", 1, 0, 0 }, { "noisy-lkup-num-reads-writes", 1, 0, 0 }, + { "noisy-fwd-mode", 1, 0, 0 }, { "no-iova-contig", 0, 0, 0 }, { "rx-mq-mode", 1, 0, 0 }, { "record-core-cycles", 0, 0, 0 },@@ -1444,6 +1446,21 @@ launch_args_parse(int argc, char** argv)rte_exit (EXIT_FAILURE ,"noisy-lkup-num-reads-writes must be >= 0\n" ); } +if (!strcmp (lgopts[opt_idx].name, +"noisy-fwd-mode" )) { +if (!strcmp (optarg,"io" ))app/test-pmd/parameters.c launch_args_parse(int argc, char** argv) · line 1461
Quoted 10 lines
app/test-pmd/parameters.c +10
-0+ noisy_fwd_mode =NOISY_FWD_MODE_IO ; + else if (!strcmp(optarg, "mac")) + noisy_fwd_mode =NOISY_FWD_MODE_MAC ; + else if (!strcmp(optarg, "macswap")) + noisy_fwd_mode =NOISY_FWD_MODE_MACSWAP ; + else if (!strcmp(optarg, "5tswap")) + noisy_fwd_mode =NOISY_FWD_MODE_5TSWAP ; + else + rte_exit(EXIT_FAILURE, "noisy-fwd-mode %s invalid -" + " must b a valid fwd mode\n",typo "be"
I would specify "..must be a valid noisy-fwd-mode value" to avoid confusion with the full set of general fwd modes and easier for user to search them in docs.
Quoted 67 lines
app/test-pmd/parameters.c +2
-0+ optarg); + }if (!strcmp (lgopts[opt_idx].name,"no-iova-contig" )) mempool_flags =RTE_MEMPOOL_F_NO_IOVA_CONTIG ;app/test-pmd/testpmd.c +5
-0@@ -364,6 +364,11 @@ uint64_t noisy_lkup_num_reads;*/ uint64_t noisy_lkup_num_reads_writes; +/* +* Configurable forwarding mode in VNF simulation. +*/ +int noisy_fwd_mode; +/* * Receive Side Scaling (RSS) configuration. */ app/test-pmd/testpmd.h +8
-0@@ -116,6 +116,13 @@ enum { QUEUE_JOB_TYPE_ACTION_QUERY, }; +enum { +NOISY_FWD_MODE_IO , +NOISY_FWD_MODE_MAC , +NOISY_FWD_MODE_MACSWAP , +NOISY_FWD_MODE_5TSWAP +}; +/** * The data structure associated with RX and TX packet burst statistics * that are recorded for each forwarding stream. @@ -561,6 +568,7 @@ extern uint64_t noisy_lkup_mem_sz;extern uint64_t noisy_lkup_num_writes;extern uint64_t noisy_lkup_num_reads;extern uint64_t noisy_lkup_num_reads_writes; +extern int noisy_fwd_mode;extern uint8_t dcb_config;doc/guides/testpmd_app_ug/run_app.rst +9
-0@@ -519,6 +519,15 @@ The command line options are: Set the number of r/w accesses to be done in noisy neighbor simulation memory buffer to N. Only available with the noisy forwarding mode. The default value is 0. +* ``--noisy-fwd-mode=mode`` + + Set the noisy vnf forwarding mode where ``mode`` is one of the following:: + + io (the default) + mac + macswap + 5tswap + * ``--no-iova-contig`` Enable to create mempool which is not IOVA contiguous. Valid only with --mp-alloc=anon.
Quoted 25 lines · Mike Pattrick
Quoted 19 lines · Kevin Traynor
Quoted 8 lines · Mike Pattrick
Previously the noisy neighbour vnf simulation would only operate in io mode, forwarding packets as is. However, this limited the usefulness of noisy neighbour simulation.
This feature has now been expanded to supporting mac, macswap, and 5tswap modes. To facilitate adding this support, some new header files were added.
Hi Mike,
I think it makes sense to allow these functionalities to be combined. It does seem like that noisy neighbour shouldn't have been added as a standalone fowarding option in the first place, as it's not mutually exclusive with the other fwding modes. Now it's forcing a user to set a fwding mode within a fwding mode to combine the functionality :/
Quoted 4 lines
The approach is to allow the fwding modes to expose their forwarding method so noisy can call them. Did you consider to expose the noisy functionality and allow the other forwarding modes to call that when the --noisy-* flags are set?
Quoted 6 lines
Personally I like this approach more, and that was the strategy I took with the previous version. However, that change didn't seem popular at the time.
http://patches.dpdk.org/project/dpdk/patch/[email protected]/#157095
Ok, interesting, I hadn't realised that. It doesn't apply anymore since David has restructured the fowarding engines, but i applied to older code and took a look.
I had been thinking to an expose a function to do the noisy processing (if any) like a do_noise() and then to return the packets to the original fowarding engine for tx, similar to what is done the opposite way around in v3. I can understand Aman's concerns about tx of pkts moved from the fwding engines to noisy fwd engine.
I think we can summarize like this (will use macswp as example) v3
- fwding engines expose their processing (e.g. do_macswp)
- user enables by setting --fwd=noisy and --noisy-fwd-mode=macswp
- noisy vnf does rx and tx
- noisy calls other fwding engine for other mode processing
- backwards compatible as existing noisy params have no effect when fwd!=noisy
v2
- noisy engine exposes a function for noise+tx
(e.g. noisy_eth_tx_burst())
- other fwd engines call this to add noise and tx
- user enables by setting --fwd=macswp and setting existing noisy params
- breaks backwards compatibility as previously noisy params would have no effect in macswp mode
It seems the ideal would be to have taken noisy as a feature, not a fwding engine but it's easy in hindsight. I'm not sure it's worth another big rework to try and add a do_noise() which may be a nice design but will break backwards compatability. So I'd probably vote for v3 design over v2.
What do others think ?
Quoted 733 lines
Quoted 534 lines
For example, a user sets fwding mode as normal 'fwd=macfwd' but then if the user adds the --noisy-* params, the macfwd'ing mode calls some functions exposed to add the noise, which seems a bit more intuitive.
Also, if someone adds a new fwding mode, they can just call the noisy functions and don't have update noisy fwding mode to add the new mode.
I'm not sure if it's better, just throwing it out there as an alternative idea.
On the downside, it would break backwards compatibility because previously those --noisy-* params would have had no effect with say macfwd mode, but now they will. So maybe that's enough to prohibit it.
In the past, I would have had all the params set and just changed fwdmode to enable/disable noisy vnf. That would behaviour would now be changed with this approach.
What do you think?
Few comments on the code below.
thanks,
Kevin.Quoted 150 lines
Signed-off-by Mike Pattrick <[email protected]>---
v2: Reverted changes to random memory lookup
v3: Refactored entire patch--- app/test-pmd/5tswap.c | 118 +---------------------- app/test-pmd/5tswap.h | 130 ++++++++++++++++++++++++++ app/test-pmd/macfwd.c | 33 +------ app/test-pmd/macfwd.h | 46 +++++++++ app/test-pmd/noisy_vnf.c | 92 +++++++++++++++--- app/test-pmd/parameters.c | 17 ++++ app/test-pmd/testpmd.c | 5 + app/test-pmd/testpmd.h | 8 ++ doc/guides/testpmd_app_ug/run_app.rst | 9 ++ 9 files changed, 299 insertions(+), 159 deletions(-)create mode 100644
app/test-pmd/5tswap.h
create mode 100644app/test-pmd/macfwd.happ/test-pmd/5tswap.c +1
-107@@ -17,64 +17,8 @@#include <rte_ip.h> #include <rte_flow.h> -#include "macswap_common.h" #include "testpmd.h" - - -static inline void -swap_mac (struct rte_ether_hdr *eth_hdr) -{ -struct rte_ether_addr addr; - -/* Swap dest and src mac addresses. */ -rte_ether_addr_copy (ð_hdr->dst_addr, &addr); -rte_ether_addr_copy (ð_hdr->src_addr, ð_hdr->dst_addr); -rte_ether_addr_copy (&addr, ð_hdr->src_addr); -} - -static inline void -swap_ipv4 (struct rte_ipv4_hdr *ipv4_hdr) -{ -rte_be32_t addr; - -/* Swap dest and src ipv4 addresses. */ - addr = ipv4_hdr->src_addr; - ipv4_hdr->src_addr = ipv4_hdr->dst_addr; - ipv4_hdr->dst_addr = addr; -} - -static inline void -swap_ipv6 (struct rte_ipv6_hdr *ipv6_hdr) -{ -uint8_t addr[16 ]; - -/* Swap dest and src ipv6 addresses. */ -memcpy (&addr, &ipv6_hdr->src_addr,16 ); -memcpy (&ipv6_hdr->src_addr, &ipv6_hdr->dst_addr,16 ); -memcpy (&ipv6_hdr->dst_addr, &addr,16 ); -} - -static inline void -swap_tcp (struct rte_tcp_hdr *tcp_hdr) -{ -rte_be16_t port; - -/* Swap dest and src tcp port. */ - port = tcp_hdr->src_port; - tcp_hdr->src_port = tcp_hdr->dst_port; - tcp_hdr->dst_port = port; -} - -static inline void -swap_udp (struct rte_udp_hdr *udp_hdr) -{ -rte_be16_t port; - -/* Swap dest and src udp port */ - port = udp_hdr->src_port; - udp_hdr->src_port = udp_hdr->dst_port; - udp_hdr->dst_port = port; -} +#include "5tswap.h" /* * 5 tuple swap forwarding mode: Swap the source and the destination of layers @@ -85,22 +29,7 @@ static bool pkt_burst_5tuple_swap(struct fwd_stream *fs) {struct rte_mbuf *pkts_burst[MAX_PKT_BURST ]; -struct rte_port *txp; -struct rte_mbuf *mb; -uint16_t next_proto; -uint64_t ol_flags; -uint16_t proto;uint16_t nb_rx; -int i; -union { -struct rte_ether_hdr *eth; -struct rte_vlan_hdr *vlan; -struct rte_ipv4_hdr *ipv4; -struct rte_ipv6_hdr *ipv6; -struct rte_tcp_hdr *tcp; -struct rte_udp_hdr *udp; -uint8_t *byte; - } h;/* * Receive a burst of packets and forward them. @@ -109,49 +38,8 @@ pkt_burst_5tuple_swap(struct fwd_stream *fs)if (unlikely (nb_rx ==0 ))return false; - txp = &ports[fs->tx_port]; - ol_flags =ol_flags_init (txp->dev_conf.txmode.offloads); -vlan_qinq_set (pkts_burst, nb_rx, ol_flags, - txp->tx_vlan_id, txp->tx_vlan_id_outer); -for (i =0 ; i < nb_rx; i++) { -if (likely (i < nb_rx -1 )) -rte_prefetch0 (rte_pktmbuf_mtod (pkts_burst[i+1 ], - void *)); - mb = pkts_burst[i]; - h.eth = rte_pktmbuf_mtod(mb, struct rte_ether_hdr *); - proto = h.eth->ether_type; -swap_mac (h.eth); - mb->l2_len =sizeof (struct rte_ether_hdr ); - h.eth++; -while (proto ==RTE_BE16 (RTE_ETHER_TYPE_VLAN ) || - proto ==RTE_BE16 (RTE_ETHER_TYPE_QINQ )) { - proto = h.vlan->eth_proto; - h.vlan++; - mb->l2_len +=sizeof (struct rte_vlan_hdr ); - } -if (proto ==RTE_BE16 (RTE_ETHER_TYPE_IPV4 )) { -swap_ipv4 (h.ipv4); - next_proto = h.ipv4->next_proto_id; - mb->l3_len =rte_ipv4_hdr_len (h.ipv4); - h.byte += mb->l3_len; - }else if (proto ==RTE_BE16 (RTE_ETHER_TYPE_IPV6 )) { -swap_ipv6 (h.ipv6); - next_proto = h.ipv6->proto; - h.ipv6++; - mb->l3_len =sizeof (struct rte_ipv6_hdr ); - }else { -mbuf_field_set (mb, ol_flags); -continue ; - } -if (next_proto ==IPPROTO_UDP ) {app/test-pmd/5tswap.c pkt_burst_5tuple_swap(struct fwd_stream *fs) · line 42
Quoted 10 lines
app/test-pmd/5tswap.c +2
-8-swap_udp (h.udp); - mb->l4_len =sizeof (struct rte_udp_hdr ); - }else if (next_proto ==IPPROTO_TCP ) { -swap_tcp (h.tcp); - mb->l4_len = (h.tcp->data_off &0xf0 ) >>2 ; - } -mbuf_field_set (mb, ol_flags); - } +do_5tswap (pkts_burst, nb_rx, fs); +this simplification is nice.
Quoted 204 lines
app/test-pmd/5tswap.c +0
-0common_fwd_stream_transmit (fs, pkts_burst, nb_rx);return true;app/test-pmd/5tswap.h new file +130
-0@@ -0,0 +1,130 @@ +/* SPDX-License-Identifier: BSD-3-Clause +* Copyright(c) 2018 Intel Corporation +*/ + +#ifndef _5TSWAP_H_ +#define _5TSWAP_H_ + +#include "macswap_common.h" + +static inline void +swap_mac (struct rte_ether_hdr *eth_hdr) +{ +struct rte_ether_addr addr; + +/* Swap dest and src mac addresses. */ +rte_ether_addr_copy (ð_hdr->dst_addr, &addr); +rte_ether_addr_copy (ð_hdr->src_addr, ð_hdr->dst_addr); +rte_ether_addr_copy (&addr, ð_hdr->src_addr); +} + +static inline void +swap_ipv4 (struct rte_ipv4_hdr *ipv4_hdr) +{ +rte_be32_t addr; + +/* Swap dest and src ipv4 addresses. */ + addr = ipv4_hdr->src_addr; + ipv4_hdr->src_addr = ipv4_hdr->dst_addr; + ipv4_hdr->dst_addr = addr; +} + +static inline void +swap_ipv6 (struct rte_ipv6_hdr *ipv6_hdr) +{ +uint8_t addr[16 ]; + +/* Swap dest and src ipv6 addresses. */ +memcpy (&addr, &ipv6_hdr->src_addr,16 ); +memcpy (&ipv6_hdr->src_addr, &ipv6_hdr->dst_addr,16 ); +memcpy (&ipv6_hdr->dst_addr, &addr,16 ); +} + +static inline void +swap_tcp (struct rte_tcp_hdr *tcp_hdr) +{ +rte_be16_t port; + +/* Swap dest and src tcp port. */ + port = tcp_hdr->src_port; + tcp_hdr->src_port = tcp_hdr->dst_port; + tcp_hdr->dst_port = port; +} + +static inline void +swap_udp (struct rte_udp_hdr *udp_hdr) +{ +rte_be16_t port; + +/* Swap dest and src udp port */ + port = udp_hdr->src_port; + udp_hdr->src_port = udp_hdr->dst_port; + udp_hdr->dst_port = port; +} + +static inline void +do_5tswap (struct rte_mbuf *pkts_burst[],uint16_t nb_rx, +struct fwd_stream *fs) +{ +struct rte_port *txp; +struct rte_mbuf *mb; +uint16_t next_proto; +uint64_t ol_flags; +uint16_t proto; +int i; +union { +struct rte_ether_hdr *eth; +struct rte_vlan_hdr *vlan; +struct rte_ipv4_hdr *ipv4; +struct rte_ipv6_hdr *ipv6; +struct rte_tcp_hdr *tcp; +struct rte_udp_hdr *udp; +uint8_t *byte; + } h; + + txp = &ports[fs->tx_port]; + ol_flags =ol_flags_init (txp->dev_conf.txmode.offloads); +vlan_qinq_set (pkts_burst, nb_rx, ol_flags, + txp->tx_vlan_id, txp->tx_vlan_id_outer); +for (i =0 ; i < nb_rx; i++) { +if (likely (i < nb_rx -1 )) +rte_prefetch0 (rte_pktmbuf_mtod (pkts_burst[i+1 ], + void *)); + mb = pkts_burst[i]; + h.eth = rte_pktmbuf_mtod(mb, struct rte_ether_hdr *); + proto = h.eth->ether_type; +swap_mac (h.eth); + mb->l2_len =sizeof (struct rte_ether_hdr ); + h.eth++; +while (proto ==RTE_BE16 (RTE_ETHER_TYPE_VLAN ) || + proto ==RTE_BE16 (RTE_ETHER_TYPE_QINQ )) { + proto = h.vlan->eth_proto; + h.vlan++; + mb->l2_len +=sizeof (struct rte_vlan_hdr ); + } +if (proto ==RTE_BE16 (RTE_ETHER_TYPE_IPV4 )) { +swap_ipv4 (h.ipv4); + next_proto = h.ipv4->next_proto_id; + mb->l3_len =rte_ipv4_hdr_len (h.ipv4); + h.byte += mb->l3_len; + }else if (proto ==RTE_BE16 (RTE_ETHER_TYPE_IPV6 )) { +swap_ipv6 (h.ipv6); + next_proto = h.ipv6->proto; + h.ipv6++; + mb->l3_len =sizeof (struct rte_ipv6_hdr ); + }else { +mbuf_field_set (mb, ol_flags); +continue ; + } +if (next_proto ==IPPROTO_UDP ) { +swap_udp (h.udp); + mb->l4_len =sizeof (struct rte_udp_hdr ); + }else if (next_proto ==IPPROTO_TCP ) { +swap_tcp (h.tcp); + mb->l4_len = (h.tcp->data_off &0xf0 ) >>2 ; + } +mbuf_field_set (mb, ol_flags); + } +} + +#endif /* _5TSWAP_H_ */ app/test-pmd/macfwd.c +2
-31@@ -35,6 +35,7 @@#include <rte_flow.h> #include "testpmd.h" +#include "macfwd.h" /* * Forwarding of packets in MAC mode. @@ -45,13 +46,7 @@ static bool pkt_burst_mac_forward(struct fwd_stream *fs) {struct rte_mbuf *pkts_burst[MAX_PKT_BURST ]; -struct rte_port *txp; -struct rte_mbuf *mb; -struct rte_ether_hdr *eth_hdr;uint16_t nb_rx; -uint16_t i; -uint64_t ol_flags =0 ; -uint64_t tx_offloads;/* * Receive a burst of packets and forward them. @@ -60,31 +55,7 @@ pkt_burst_mac_forward(struct fwd_stream *fs)if (unlikely (nb_rx ==0 ))return false; - txp = &ports[fs->tx_port]; - tx_offloads = txp->dev_conf.txmode.offloads; -if (tx_offloads &RTE_ETH_TX_OFFLOAD_VLAN_INSERT ) - ol_flags =RTE_MBUF_F_TX_VLAN ; -if (tx_offloads &RTE_ETH_TX_OFFLOAD_QINQ_INSERT ) - ol_flags |=RTE_MBUF_F_TX_QINQ ; -if (tx_offloads &RTE_ETH_TX_OFFLOAD_MACSEC_INSERT ) - ol_flags |=RTE_MBUF_F_TX_MACSEC ; -for (i =0 ; i < nb_rx; i++) { -if (likely (i < nb_rx -1 )) -rte_prefetch0 (rte_pktmbuf_mtod (pkts_burst[i +1 ], - void *)); - mb = pkts_burst[i]; - eth_hdr = rte_pktmbuf_mtod(mb, struct rte_ether_hdr *); -rte_ether_addr_copy (&peer_eth_addrs[fs->peer_addr], - ð_hdr->dst_addr); -rte_ether_addr_copy (&ports[fs->tx_port].eth_addr, - ð_hdr->src_addr); - mb->ol_flags &=RTE_MBUF_F_INDIRECT |RTE_MBUF_F_EXTERNAL ; - mb->ol_flags |= ol_flags; - mb->l2_len =sizeof (struct rte_ether_hdr ); - mb->l3_len =sizeof (struct rte_ipv4_hdr ); - mb->vlan_tci = txp->tx_vlan_id; - mb->vlan_tci_outer = txp->tx_vlan_id_outer; - } +do_macfwd (pkts_burst, nb_rx, fs);common_fwd_stream_transmit (fs, pkts_burst, nb_rx);app/test-pmd/macfwd.h new file +0
-0app/test-pmd/macfwd.h line 10
Quoted 10 lines
app/test-pmd/macfwd.h new file +10
-0@@ -0,0 +1,46 @@ +/* SPDX-License-Identifier: BSD-3-Clause +* Copyright(c) 2018 Intel Corporation +*/ + +#ifndef _MACFWD_H_ +#define _MACFWD_H_ + +static inline void +do_macfwd (struct rte_mbuf *pkts_burst[],uint16_t nb_rx, +struct fwd_stream *fs)nit: indent/alignment is a little off here. There is some extra spaces. Same with other do_*()
app/test-pmd/macfwd.h line 19
Quoted 9 lines
app/test-pmd/macfwd.h new file +9
-0+{ +struct rte_ether_hdr *eth_hdr; +uint64_t ol_flags =0 ; +uint64_t tx_offloads; +struct rte_mbuf *mb; +struct rte_port *txp = &ports[fs->tx_port]; +uint16_t i; + +can remove addition blank line
Quoted 51 lines
app/test-pmd/macfwd.h new file +27
-0+ tx_offloads = txp->dev_conf.txmode.offloads; +if (tx_offloads &RTE_ETH_TX_OFFLOAD_VLAN_INSERT ) + ol_flags =RTE_MBUF_F_TX_VLAN ; +if (tx_offloads &RTE_ETH_TX_OFFLOAD_QINQ_INSERT ) + ol_flags |=RTE_MBUF_F_TX_QINQ ; +if (tx_offloads &RTE_ETH_TX_OFFLOAD_MACSEC_INSERT ) + ol_flags |=RTE_MBUF_F_TX_MACSEC ; +for (i =0 ; i < nb_rx; i++) { +if (likely (i < nb_rx -1 )) +rte_prefetch0 (rte_pktmbuf_mtod (pkts_burst[i +1 ], + void *)); + mb = pkts_burst[i]; + eth_hdr = rte_pktmbuf_mtod(mb, struct rte_ether_hdr *); +rte_ether_addr_copy (&peer_eth_addrs[fs->peer_addr], + ð_hdr->dst_addr); +rte_ether_addr_copy (&ports[fs->tx_port].eth_addr, + ð_hdr->src_addr); + mb->ol_flags &=RTE_MBUF_F_INDIRECT |RTE_MBUF_F_EXTERNAL ; + mb->ol_flags |= ol_flags; + mb->l2_len =sizeof (struct rte_ether_hdr ); + mb->l3_len =sizeof (struct rte_ipv4_hdr ); + mb->vlan_tci = txp->tx_vlan_id; + mb->vlan_tci_outer = txp->tx_vlan_id_outer; + } +} + +#endif /* _MACFWD_H_ */ app/test-pmd/noisy_vnf.c +12
-0@@ -32,6 +32,18 @@#include <rte_malloc.h> #include "testpmd.h" +#include "5tswap.h" +#include "macfwd.h" +#if defined(RTE_ARCH_X86 ) +#include "macswap_sse.h" +#elif defined(__ARM_NEON) +#include "macswap_neon.h" +#else +#include "macswap.h" +#endif + +#define NOISY_STRSIZE 256 +#define NOISY_RING "noisy_ring_%d\n"struct noisy_config {struct rte_ring *f;app/test-pmd/noisy_vnf.c sim_memory_lookups(struct noisy_config *ncf, uint16_t nb_pkts) · line 85
Quoted 6 lines
app/test-pmd/noisy_vnf.c +0
-3@@ -80,9 +92,6 @@ sim_memory_lookups(struct noisy_config *ncf, uint16_t nb_pkts) {uint16_t i, j; -if (!ncf->do_sim) -return ; -Why is this removed? It's not checked before all calls to this function
Quoted 56 lines
app/test-pmd/noisy_vnf.c +17
-6for (i =0 ; i < nb_pkts; i++) {for (j =0 ; j < noisy_lkup_num_writes; j++)do_write (ncf->vnf_mem);@@ -110,15 +119,13 @@ sim_memory_lookups(struct noisy_config *ncf, uint16_t nb_pkts)* out of the FIFO * 4. Cases 2 and 3 combined */ -static bool -pkt_burst_noisy_vnf (struct fwd_stream *fs) +static uint16_t +noisy_eth_tx_burst (struct fwd_stream *fs,uint16_t nb_rx,struct rte_mbuf **pkts_burst) {const uint64_t freq_khz =rte_get_timer_hz () /1000 ;struct noisy_config *ncf = noisy_cfg[fs->rx_port]; -struct rte_mbuf *pkts_burst[MAX_PKT_BURST ];struct rte_mbuf *tmp_pkts[MAX_PKT_BURST ];uint16_t nb_deqd =0 ; -uint16_t nb_rx =0 ;uint16_t nb_tx =0 ;uint16_t nb_enqd;unsigned int fifo_free;@@ -126,12 +133,12 @@ pkt_burst_noisy_vnf(struct fwd_stream *fs)bool needs_flush = false;uint64_t now; - nb_rx =common_fwd_stream_receive (fs, pkts_burst, nb_pkt_per_burst);if (unlikely (nb_rx ==0 )) goto flush;if (!ncf->do_buffering) { -sim_memory_lookups (ncf, nb_rx); +if (ncf->do_sim) +sim_memory_lookups (ncf, nb_rx); nb_tx =common_fwd_stream_transmit (fs, pkts_burst, nb_rx); goto end; }@@ -169,11 +176,61 @@ pkt_burst_noisy_vnf(struct fwd_stream *fs) ncf->prev_time =rte_get_timer_cycles (); } end: +return nb_tx; +} + +static bool +pkt_burst_io (struct fwd_stream *fs) +{ +struct rte_mbuf *pkts_burst[MAX_PKT_BURST ]; +uint16_t nb_rx; +uint16_t nb_tx; + + nb_rx =common_fwd_stream_receive (fs, pkts_burst, nb_pkt_per_burst); + nb_tx =noisy_eth_tx_burst (fs, nb_rx, pkts_burst); +return nb_rx >0 || nb_tx >0 ; }Quoted 13 lines
app/test-pmd/noisy_vnf.c pkt_burst_noisy_vnf(struct fwd_stream *fs) · line 202
Quoted 10 lines
app/test-pmd/noisy_vnf.c +8
-2-#define NOISY_STRSIZE 256 -#define NOISY_RING "noisy_ring_%d\n" +static bool +pkt_burst_mac (struct fwd_stream *fs) +{ +struct rte_mbuf *pkts_burst[MAX_PKT_BURST ]; +uint16_t nb_rx; +uint16_t nb_tx; + + nb_rx =common_fwd_stream_receive (fs, pkts_burst, nb_pkt_per_burst);Similar to
macfwd.c, you can add check forunlikely(nb_rx == 0)at this point in these fns.That's true. I removed it because I'll have to call
noisy_eth_tx_burst()regardless, but we could avoid the middle call in these locations.I agree with the other suggestions.
Thanks,
MQuoted 175 lines
app/test-pmd/noisy_vnf.c pkt_burst_noisy_vnf(struct fwd_stream *fs) · line 213
Quoted 12 lines
app/test-pmd/noisy_vnf.c +11
-0+do_macfwd (pkts_burst, nb_rx, fs); + nb_tx =noisy_eth_tx_burst (fs, nb_rx, pkts_burst); + +return nb_rx >0 || nb_tx >0 ; +} +static bool +pkt_burst_macswap (struct fwd_stream *fs) +{ +struct rte_mbuf *pkts_burst[MAX_PKT_BURST ]; +uint16_t nb_rx =0 ; +uint16_t nb_tx =0 ;nit: these are not assigned in the other functions
Quoted 75 lines
app/test-pmd/noisy_vnf.c +31
-2+ + nb_rx =common_fwd_stream_receive (fs, pkts_burst, nb_pkt_per_burst); +do_macswap (pkts_burst, nb_rx, &ports[fs->tx_port]); + nb_tx =noisy_eth_tx_burst (fs, nb_rx, pkts_burst); + +return nb_rx >0 || nb_tx >0 ; +} +static bool +pkt_brust_5tswap (struct fwd_stream *fs) +{ +struct rte_mbuf *pkts_burst[MAX_PKT_BURST ]; +uint16_t nb_rx =0 ; +uint16_t nb_tx =0 ; + + nb_rx =common_fwd_stream_receive (fs, pkts_burst, nb_pkt_per_burst); +do_5tswap (pkts_burst, nb_rx, fs); + nb_tx =noisy_eth_tx_burst (fs, nb_rx, pkts_burst); + +return nb_rx >0 || nb_tx >0 ; +}static void noisy_fwd_end (portid_t pi)@@ -226,6 +283,15 @@ noisy_fwd_begin(portid_t pi) "--noisy-lkup-memory-size must be > 0\n"); } +if (noisy_fwd_mode ==NOISY_FWD_MODE_IO ) + noisy_vnf_engine.packet_fwd = pkt_burst_io; +else if (noisy_fwd_mode ==NOISY_FWD_MODE_MAC ) + noisy_vnf_engine.packet_fwd = pkt_burst_mac; +else if (noisy_fwd_mode ==NOISY_FWD_MODE_MACSWAP ) + noisy_vnf_engine.packet_fwd = pkt_burst_macswap; +else if (noisy_fwd_mode ==NOISY_FWD_MODE_5TSWAP ) + noisy_vnf_engine.packet_fwd = pkt_brust_5tswap; +return 0 ; }@@ -233,6 +299,6 @@ struct fwd_engine noisy_vnf_engine = { .fwd_mode_name = "noisy", .port_fwd_begin = noisy_fwd_begin, .port_fwd_end = noisy_fwd_end, - .stream_init = common_fwd_stream_init, - .packet_fwd = pkt_burst_noisy_vnf, + .stream_init = common_fwd_stream_init, + .packet_fwd = pkt_burst_io, };app/test-pmd/parameters.c +5
-0@@ -196,6 +196,7 @@ usage(char* progname)printf (" --noisy-lkup-num-writes=N: do N random writes per packet\n" );printf (" --noisy-lkup-num-reads=N: do N random reads per packet\n" );printf (" --noisy-lkup-num-reads-writes=N: do N random reads and writes per packet\n" ); +printf (" --noisy-fwd-mode=mode: set the fwd mode\n" );printf (" --no-iova-contig: mempool memory can be IOVA non contiguous. " "valid only with --mp-alloc=anon\n" ); printf(" --rx-mq-mode=0xX: hexadecimal bitmask of RX mq mode can be "@@ -704,6 +705,7 @@ launch_args_parse(int argc, char** argv) { "noisy-lkup-num-writes", 1, 0, 0 }, { "noisy-lkup-num-reads", 1, 0, 0 }, { "noisy-lkup-num-reads-writes", 1, 0, 0 }, + { "noisy-fwd-mode", 1, 0, 0 }, { "no-iova-contig", 0, 0, 0 }, { "rx-mq-mode", 1, 0, 0 }, { "record-core-cycles", 0, 0, 0 },@@ -1444,6 +1446,21 @@ launch_args_parse(int argc, char** argv)rte_exit (EXIT_FAILURE ,"noisy-lkup-num-reads-writes must be >= 0\n" ); } +if (!strcmp (lgopts[opt_idx].name, +"noisy-fwd-mode" )) { +if (!strcmp (optarg,"io" ))app/test-pmd/parameters.c launch_args_parse(int argc, char** argv) · line 1461
Quoted 10 lines
app/test-pmd/parameters.c +10
-0+ noisy_fwd_mode =NOISY_FWD_MODE_IO ; + else if (!strcmp(optarg, "mac")) + noisy_fwd_mode =NOISY_FWD_MODE_MAC ; + else if (!strcmp(optarg, "macswap")) + noisy_fwd_mode =NOISY_FWD_MODE_MACSWAP ; + else if (!strcmp(optarg, "5tswap")) + noisy_fwd_mode =NOISY_FWD_MODE_5TSWAP ; + else + rte_exit(EXIT_FAILURE, "noisy-fwd-mode %s invalid -" + " must b a valid fwd mode\n",typo "be"
I would specify "..must be a valid noisy-fwd-mode value" to avoid confusion with the full set of general fwd modes and easier for user to search them in docs.
Quoted 67 lines
app/test-pmd/parameters.c +2
-0+ optarg); + }if (!strcmp (lgopts[opt_idx].name,"no-iova-contig" )) mempool_flags =RTE_MEMPOOL_F_NO_IOVA_CONTIG ;app/test-pmd/testpmd.c +5
-0@@ -364,6 +364,11 @@ uint64_t noisy_lkup_num_reads;*/ uint64_t noisy_lkup_num_reads_writes; +/* +* Configurable forwarding mode in VNF simulation. +*/ +int noisy_fwd_mode; +/* * Receive Side Scaling (RSS) configuration. */ app/test-pmd/testpmd.h +8
-0@@ -116,6 +116,13 @@ enum { QUEUE_JOB_TYPE_ACTION_QUERY, }; +enum { +NOISY_FWD_MODE_IO , +NOISY_FWD_MODE_MAC , +NOISY_FWD_MODE_MACSWAP , +NOISY_FWD_MODE_5TSWAP +}; +/** * The data structure associated with RX and TX packet burst statistics * that are recorded for each forwarding stream. @@ -561,6 +568,7 @@ extern uint64_t noisy_lkup_mem_sz;extern uint64_t noisy_lkup_num_writes;extern uint64_t noisy_lkup_num_reads;extern uint64_t noisy_lkup_num_reads_writes; +extern int noisy_fwd_mode;extern uint8_t dcb_config;doc/guides/testpmd_app_ug/run_app.rst +9
-0@@ -519,6 +519,15 @@ The command line options are: Set the number of r/w accesses to be done in noisy neighbor simulation memory buffer to N. Only available with the noisy forwarding mode. The default value is 0. +* ``--noisy-fwd-mode=mode`` + + Set the noisy vnf forwarding mode where ``mode`` is one of the following:: + + io (the default) + mac + macswap + 5tswap + * ``--no-iova-contig`` Enable to create mempool which is not IOVA contiguous. Valid only with --mp-alloc=anon.
Quoted 61 lines · Kevin Traynor
Quoted 26 lines · Mike Pattrick
Quoted 19 lines · Kevin Traynor
Quoted 8 lines · Mike Pattrick
Previously the noisy neighbour vnf simulation would only operate in io mode, forwarding packets as is. However, this limited the usefulness of noisy neighbour simulation.
This feature has now been expanded to supporting mac, macswap, and 5tswap modes. To facilitate adding this support, some new header files were added.
Hi Mike,
I think it makes sense to allow these functionalities to be combined. It does seem like that noisy neighbour shouldn't have been added as a standalone fowarding option in the first place, as it's not mutually exclusive with the other fwding modes. Now it's forcing a user to set a fwding mode within a fwding mode to combine the functionality :/
Quoted 4 lines
The approach is to allow the fwding modes to expose their forwarding method so noisy can call them. Did you consider to expose the noisy functionality and allow the other forwarding modes to call that when the --noisy-* flags are set?
Quoted 6 lines
Personally I like this approach more, and that was the strategy I took with the previous version. However, that change didn't seem popular at the time.
http://patches.dpdk.org/project/dpdk/patch/[email protected]/#157095
Ok, interesting, I hadn't realised that. It doesn't apply anymore since David has restructured the fowarding engines, but i applied to older code and took a look.
I had been thinking to an expose a function to do the noisy processing (if any) like a
do_noise()and then to return the packets to the original fowarding engine for tx, similar to what is done the opposite way around in v3. I can understand Aman's concerns about tx of pkts moved from the fwding engines to noisy fwd engine.I think we can summarize like this (will use macswp as example) v3
- fwding engines expose their processing (e.g.do_macswp)
- user enables by setting --fwd=noisy and --noisy-fwd-mode=macswp
- noisy vnf does rx and tx
- noisy calls other fwding engine for other mode processing
- backwards compatible as existing noisy params have no effect when fwd!=noisyv2
- noisy engine exposes a function for noise+tx
(e.g.noisy_eth_tx_burst())
- other fwd engines call this to add noise and tx
- user enables by setting --fwd=macswp and setting existing noisy params
- breaks backwards compatibility as previously noisy params would have no effect in macswp mode
Quoted 8 lines
It seems the ideal would be to have taken noisy as a feature, not a fwding engine but it's easy in hindsight. I'm not sure it's worth another big rework to try and add a
do_noise()which may be a nice design but will break backwards compatability. So I'd probably vote for v3 design over v2.What do others think ?
Hi Kevin, Mike,
I think better to keep noisy neighbour forwarding mode separate.
testpmd forwarding modes are used a lot, and noisy neighbor impacts forwarding, indeed that is the intension of the feature, right, but we don't need this noise most of the times.
Other option can be embedding noisy neighbor into other forwarding modes, but it will bring complexity to main usage of the other forwarding modes.
Mike seems able to abstract the main function of the forwarding and use it in both main forwarding function and noisy neighbour forwarding, this looks good to me.
Quoted 767 lines
Quoted 766 lines
Quoted 544 lines
For example, a user sets fwding mode as normal 'fwd=macfwd' but then if the user adds the --noisy-* params, the macfwd'ing mode calls some functions exposed to add the noise, which seems a bit more intuitive.
Also, if someone adds a new fwding mode, they can just call the noisy functions and don't have update noisy fwding mode to add the new mode.
I'm not sure if it's better, just throwing it out there as an alternative idea.
On the downside, it would break backwards compatibility because previously those --noisy-* params would have had no effect with say macfwd mode, but now they will. So maybe that's enough to prohibit it.
In the past, I would have had all the params set and just changed fwdmode to enable/disable noisy vnf. That would behaviour would now be changed with this approach.
What do you think?
Few comments on the code below.
thanks,
Kevin.Quoted 152 lines
Signed-off-by Mike Pattrick <[email protected]>---
v2: Reverted changes to random memory lookup
v3: Refactored entire patch
---
app/test-pmd/5tswap.c | 118 +---------------------- app/test-pmd/5tswap.h | 130
++++++++++++++++++++++++++
app/test-pmd/macfwd.c | 33 +------ app/test-pmd/macfwd.h | 46 +++++++++ app/test-pmd/noisy_vnf.c | 92 +++++++++++++++--- app/test-pmd/parameters.c | 17 ++++ app/test-pmd/testpmd.c | 5 + app/test-pmd/testpmd.h | 8 ++doc/guides/testpmd_app_ug/run_app.rst| 9 ++9 files changed, 299 insertions(+), 159 deletions(-)create mode 100644
app/test-pmd/5tswap.h
create mode 100644app/test-pmd/macfwd.happ/test-pmd/5tswap.c +1
-57@@ -17,64 +17,8 @@ #include <rte_ip.h> #include <rte_flow.h> -#include "macswap_common.h" #include "testpmd.h" - - -static inline void -swap_mac (struct rte_ether_hdr *eth_hdr) -{ - struct rte_ether_addr addr; - - /* Swap dest and src mac addresses. */ - rte_ether_addr_copy(ð_hdr->dst_addr, &addr); - rte_ether_addr_copy(ð_hdr->src_addr, ð_hdr->dst_addr); - rte_ether_addr_copy(&addr, ð_hdr->src_addr); -} - -static inline void -swap_ipv4 (struct rte_ipv4_hdr *ipv4_hdr) -{ - rte_be32_t addr; - - /* Swap dest and src ipv4 addresses. */ - addr = ipv4_hdr->src_addr; - ipv4_hdr->src_addr = ipv4_hdr->dst_addr; - ipv4_hdr->dst_addr = addr; -} - -static inline void -swap_ipv6 (struct rte_ipv6_hdr *ipv6_hdr) -{ - uint8_t addr[16]; - - /* Swap dest and src ipv6 addresses. */ - memcpy(&addr, &ipv6_hdr->src_addr, 16); - memcpy(&ipv6_hdr->src_addr, &ipv6_hdr->dst_addr, 16); - memcpy(&ipv6_hdr->dst_addr, &addr, 16); -} - -static inline void -swap_tcp (struct rte_tcp_hdr *tcp_hdr) -{ - rte_be16_t port; - - /* Swap dest and src tcp port. */ - port = tcp_hdr->src_port; - tcp_hdr->src_port = tcp_hdr->dst_port; - tcp_hdr->dst_port = port; -} - -static inline void -swap_udp (struct rte_udp_hdr *udp_hdr) -{ - rte_be16_t port; - - /* Swap dest and src udp port */ - port = udp_hdr->src_port; - udp_hdr->src_port = udp_hdr->dst_port; - udp_hdr->dst_port = port; -} +#include "5tswap.h" /** 5 tuple swap forwarding mode: Swap the source and the destination of layers
app/test-pmd/5tswap.c +0
-50@@ -85,22 +29,7 @@ static bool pkt_burst_5tuple_swap(struct fwd_stream *fs) { struct rte_mbuf *pkts_burst[MAX_PKT_BURST]; - struct rte_port *txp; - struct rte_mbuf *mb; - uint16_t next_proto; - uint64_t ol_flags; - uint16_t proto; uint16_t nb_rx; - int i; - union { - struct rte_ether_hdr *eth; - struct rte_vlan_hdr *vlan; - struct rte_ipv4_hdr *ipv4; - struct rte_ipv6_hdr *ipv6; - struct rte_tcp_hdr *tcp; - struct rte_udp_hdr *udp; - uint8_t *byte; - } h; /** Receive a burst of packets and forward them. @@ -109,49 +38,8 @@ pkt_burst_5tuple_swap(struct fwd_stream *fs) if (unlikely(nb_rx == 0)) return false; - txp = &ports[fs->tx_port]; - ol_flags = ol_flags_init(txp->dev_conf.txmode.offloads); - vlan_qinq_set(pkts_burst, nb_rx, ol_flags, - txp->tx_vlan_id, txp->tx_vlan_id_outer); - for (i = 0; i < nb_rx; i++) { - if (likely(i < nb_rx - 1)) - rte_prefetch0(rte_pktmbuf_mtod(pkts_burst[i+1], - void *)); - mb = pkts_burst[i]; - h.eth = rte_pktmbuf_mtod(mb, struct rte_ether_hdr *); - proto = h.eth->ether_type; - swap_mac(h.eth); - mb->l2_len = sizeof(struct rte_ether_hdr); - h.eth++; - while (proto == RTE_BE16(RTE_ETHER_TYPE_VLAN) || - proto == RTE_BE16(RTE_ETHER_TYPE_QINQ)) { - proto = h.vlan->eth_proto; - h.vlan++; - mb->l2_len += sizeof(struct rte_vlan_hdr); - } - if (proto == RTE_BE16(RTE_ETHER_TYPE_IPV4)) { - swap_ipv4(h.ipv4); - next_proto = h.ipv4->next_proto_id; - mb->l3_len = rte_ipv4_hdr_len(h.ipv4); - h.byte += mb->l3_len; - } else if (proto == RTE_BE16(RTE_ETHER_TYPE_IPV6)) { - swap_ipv6(h.ipv6); - next_proto = h.ipv6->proto; - h.ipv6++; - mb->l3_len = sizeof(struct rte_ipv6_hdr); - } else { - mbuf_field_set(mb, ol_flags); - continue; - } - if (next_proto == IPPROTO_UDP) {app/test-pmd/5tswap.c pkt_burst_5tuple_swap(struct fwd_stream *fs) · line 42
Quoted 10 lines
app/test-pmd/5tswap.c +2
-8- swap_udp(h.udp); - mb->l4_len = sizeof(struct rte_udp_hdr); - } else if (next_proto == IPPROTO_TCP) { - swap_tcp(h.tcp); - mb->l4_len = (h.tcp->data_off & 0xf0) >> 2; - } - mbuf_field_set(mb, ol_flags); - } + do_5tswap(pkts_burst, nb_rx, fs); +this simplification is nice.
Quoted 205 lines
app/test-pmd/5tswap.c +0
-0common_fwd_stream_transmit(fs, pkts_burst, nb_rx); return true;app/test-pmd/5tswap.h new file +130
-0@@ -0,0 +1,130 @@ +/* SPDX-License-Identifier: BSD-3-Clause +* Copyright(c) 2018 Intel Corporation +*/ + +#ifndef _5TSWAP_H_ +#define _5TSWAP_H_ + +#include "macswap_common.h" + +static inline void +swap_mac (struct rte_ether_hdr *eth_hdr) +{ + struct rte_ether_addr addr; + + /* Swap dest and src mac addresses. */ + rte_ether_addr_copy(ð_hdr->dst_addr, &addr); + rte_ether_addr_copy(ð_hdr->src_addr, ð_hdr->dst_addr); + rte_ether_addr_copy(&addr, ð_hdr->src_addr); +} + +static inline void +swap_ipv4 (struct rte_ipv4_hdr *ipv4_hdr) +{ + rte_be32_t addr; + + /* Swap dest and src ipv4 addresses. */ + addr = ipv4_hdr->src_addr; + ipv4_hdr->src_addr = ipv4_hdr->dst_addr; + ipv4_hdr->dst_addr = addr; +} + +static inline void +swap_ipv6 (struct rte_ipv6_hdr *ipv6_hdr) +{ + uint8_t addr[16]; + + /* Swap dest and src ipv6 addresses. */ + memcpy(&addr, &ipv6_hdr->src_addr, 16); + memcpy(&ipv6_hdr->src_addr, &ipv6_hdr->dst_addr, 16); + memcpy(&ipv6_hdr->dst_addr, &addr, 16); +} + +static inline void +swap_tcp (struct rte_tcp_hdr *tcp_hdr) +{ + rte_be16_t port; + + /* Swap dest and src tcp port. */ + port = tcp_hdr->src_port; + tcp_hdr->src_port = tcp_hdr->dst_port; + tcp_hdr->dst_port = port; +} + +static inline void +swap_udp (struct rte_udp_hdr *udp_hdr) +{ + rte_be16_t port; + + /* Swap dest and src udp port */ + port = udp_hdr->src_port; + udp_hdr->src_port = udp_hdr->dst_port; + udp_hdr->dst_port = port; +} + +static inline void +do_5tswap (struct rte_mbuf *pkts_burst[],uint16_t nb_rx, + struct fwd_stream *fs) +{ + struct rte_port *txp; + struct rte_mbuf *mb; + uint16_t next_proto; + uint64_t ol_flags; + uint16_t proto; + int i; + union { + struct rte_ether_hdr *eth; + struct rte_vlan_hdr *vlan; + struct rte_ipv4_hdr *ipv4; + struct rte_ipv6_hdr *ipv6; + struct rte_tcp_hdr *tcp; + struct rte_udp_hdr *udp; + uint8_t *byte; + } h; + + txp = &ports[fs->tx_port]; + ol_flags = ol_flags_init(txp->dev_conf.txmode.offloads); + vlan_qinq_set(pkts_burst, nb_rx, ol_flags, + txp->tx_vlan_id, txp->tx_vlan_id_outer); + for (i = 0; i < nb_rx; i++) { + if (likely(i < nb_rx - 1)) + rte_prefetch0(rte_pktmbuf_mtod(pkts_burst[i+1], + void *)); + mb = pkts_burst[i]; + h.eth = rte_pktmbuf_mtod(mb, struct rte_ether_hdr *); + proto = h.eth->ether_type; + swap_mac(h.eth); + mb->l2_len = sizeof(struct rte_ether_hdr); + h.eth++; + while (proto == RTE_BE16(RTE_ETHER_TYPE_VLAN) || + proto == RTE_BE16(RTE_ETHER_TYPE_QINQ)) { + proto = h.vlan->eth_proto; + h.vlan++; + mb->l2_len += sizeof(struct rte_vlan_hdr); + } + if (proto == RTE_BE16(RTE_ETHER_TYPE_IPV4)) { + swap_ipv4(h.ipv4); + next_proto = h.ipv4->next_proto_id; + mb->l3_len = rte_ipv4_hdr_len(h.ipv4); + h.byte += mb->l3_len; + } else if (proto == RTE_BE16(RTE_ETHER_TYPE_IPV6)) { + swap_ipv6(h.ipv6); + next_proto = h.ipv6->proto; + h.ipv6++; + mb->l3_len = sizeof(struct rte_ipv6_hdr); + } else { + mbuf_field_set(mb, ol_flags); + continue; + } + if (next_proto == IPPROTO_UDP) { + swap_udp(h.udp); + mb->l4_len = sizeof(struct rte_udp_hdr); + } else if (next_proto == IPPROTO_TCP) { + swap_tcp(h.tcp); + mb->l4_len = (h.tcp->data_off & 0xf0) >> 2; + } + mbuf_field_set(mb, ol_flags); + } +} + +#endif /* _5TSWAP_H_ */ app/test-pmd/macfwd.c +2
-31@@ -35,6 +35,7 @@ #include <rte_flow.h> #include "testpmd.h" +#include "macfwd.h" /** Forwarding of packets in MAC mode. @@ -45,13 +46,7 @@ static bool pkt_burst_mac_forward(struct fwd_stream *fs) { struct rte_mbuf *pkts_burst[MAX_PKT_BURST]; - struct rte_port *txp; - struct rte_mbuf *mb; - struct rte_ether_hdr *eth_hdr; uint16_t nb_rx; - uint16_t i; - uint64_t ol_flags = 0; - uint64_t tx_offloads; /** Receive a burst of packets and forward them. @@ -60,31 +55,7 @@ pkt_burst_mac_forward(struct fwd_stream *fs) if (unlikely(nb_rx == 0)) return false; - txp = &ports[fs->tx_port]; - tx_offloads = txp->dev_conf.txmode.offloads; - if (tx_offloads & RTE_ETH_TX_OFFLOAD_VLAN_INSERT) - ol_flags = RTE_MBUF_F_TX_VLAN; - if (tx_offloads & RTE_ETH_TX_OFFLOAD_QINQ_INSERT) - ol_flags |= RTE_MBUF_F_TX_QINQ; - if (tx_offloads & RTE_ETH_TX_OFFLOAD_MACSEC_INSERT) - ol_flags |= RTE_MBUF_F_TX_MACSEC; - for (i = 0; i < nb_rx; i++) { - if (likely(i < nb_rx - 1)) - rte_prefetch0(rte_pktmbuf_mtod(pkts_burst[i + 1], - void *)); - mb = pkts_burst[i]; - eth_hdr = rte_pktmbuf_mtod(mb, struct rte_ether_hdr *); - rte_ether_addr_copy(&peer_eth_addrs[fs->peer_addr], - ð_hdr->dst_addr); - rte_ether_addr_copy(&ports[fs->tx_port].eth_addr, - ð_hdr->src_addr); - mb->ol_flags &= RTE_MBUF_F_INDIRECT |RTE_MBUF_F_EXTERNAL ; - mb->ol_flags |= ol_flags; - mb->l2_len = sizeof(struct rte_ether_hdr); - mb->l3_len = sizeof(struct rte_ipv4_hdr); - mb->vlan_tci = txp->tx_vlan_id; - mb->vlan_tci_outer = txp->tx_vlan_id_outer; - } + do_macfwd(pkts_burst, nb_rx, fs); common_fwd_stream_transmit(fs, pkts_burst, nb_rx);app/test-pmd/macfwd.h new file +0
-0app/test-pmd/macfwd.h line 10
Quoted 10 lines
app/test-pmd/macfwd.h new file +10
-0@@ -0,0 +1,46 @@ +/* SPDX-License-Identifier: BSD-3-Clause +* Copyright(c) 2018 Intel Corporation +*/ + +#ifndef _MACFWD_H_ +#define _MACFWD_H_ + +static inline void +do_macfwd (struct rte_mbuf *pkts_burst[],uint16_t nb_rx, + struct fwd_stream *fs)nit: indent/alignment is a little off here. There is some extra spaces. Same with other do_*()
app/test-pmd/macfwd.h line 19
Quoted 9 lines
app/test-pmd/macfwd.h new file +9
-0+{ + struct rte_ether_hdr *eth_hdr; + uint64_t ol_flags = 0; + uint64_t tx_offloads; + struct rte_mbuf *mb; + struct rte_port *txp = &ports[fs->tx_port]; + uint16_t i; + +can remove addition blank line
Quoted 52 lines
app/test-pmd/macfwd.h new file +18
-0+ tx_offloads = txp->dev_conf.txmode.offloads; + if (tx_offloads & RTE_ETH_TX_OFFLOAD_VLAN_INSERT) + ol_flags = RTE_MBUF_F_TX_VLAN; + if (tx_offloads & RTE_ETH_TX_OFFLOAD_QINQ_INSERT) + ol_flags |= RTE_MBUF_F_TX_QINQ; + if (tx_offloads & RTE_ETH_TX_OFFLOAD_MACSEC_INSERT) + ol_flags |= RTE_MBUF_F_TX_MACSEC; + for (i = 0; i < nb_rx; i++) { + if (likely(i < nb_rx - 1)) + rte_prefetch0(rte_pktmbuf_mtod(pkts_burst[i + 1], + void *)); + mb = pkts_burst[i]; + eth_hdr = rte_pktmbuf_mtod(mb, struct rte_ether_hdr *); + rte_ether_addr_copy(&peer_eth_addrs[fs->peer_addr], + ð_hdr->dst_addr); + rte_ether_addr_copy(&ports[fs->tx_port].eth_addr, + ð_hdr->src_addr); + mb->ol_flags &= RTE_MBUF_F_INDIRECT |
RTE_MBUF_F_EXTERNAL;
+mb->ol_flags|=ol_flags;
+mb->l2_len=sizeof(struct rte_ether_hdr); +mb->l3_len=sizeof(struct rte_ipv4_hdr); +mb->vlan_tci=txp->tx_vlan_id;
+mb->vlan_tci_outer=txp->tx_vlan_id_outer; + }app/test-pmd/macfwd.h new file +3
-0+} + +#endif /* _MACFWD_H_ */ app/test-pmd/noisy_vnf.c +12
-0@@ -32,6 +32,18 @@ #include <rte_malloc.h> #include "testpmd.h" +#include "5tswap.h" +#include "macfwd.h" +#if defined(RTE_ARCH_X86 ) +#include "macswap_sse.h" +#elif defined(__ARM_NEON) +#include "macswap_neon.h" +#else +#include "macswap.h" +#endif + +#define NOISY_STRSIZE 256 +#define NOISY_RING "noisy_ring_%d\n" struct noisy_config { struct rte_ring *f;app/test-pmd/noisy_vnf.c sim_memory_lookups(struct noisy_config *ncf, · line 86
Quoted 7 lines
app/test-pmd/noisy_vnf.c +0
-3@@ -80,9 +92,6 @@ sim_memory_lookups(struct noisy_config *ncf, uint16_t nb_pkts) { uint16_t i, j; - if (!ncf->do_sim) - return; -Why is this removed? It's not checked before all calls to this function
Quoted 61 lines
app/test-pmd/noisy_vnf.c +0
-0for (i = 0; i < nb_pkts; i++) { for (j = 0; j < noisy_lkup_num_writes; j++)
do_write(ncf->vnf_mem);app/test-pmd/noisy_vnf.c +2
-4@@ -110,15 +119,13 @@ sim_memory_lookups(struct noisy_config *ncf,uint16_t nb_pkts) * out of the FIFO * 4. Cases 2 and 3 combined */ -static bool -pkt_burst_noisy_vnf(struct fwd_stream *fs) +static uint16_t +noisy_eth_tx_burst (struct fwd_stream *fs,uint16_t nb_rx,struct rte_mbuf **pkts_burst) { const uint64_t freq_khz = rte_get_timer_hz() / 1000; struct noisy_config *ncf = noisy_cfg[fs->rx_port]; - struct rte_mbuf *pkts_burst[MAX_PKT_BURST]; struct rte_mbuf *tmp_pkts[MAX_PKT_BURST]; uint16_t nb_deqd = 0; - uint16_t nb_rx = 0; uint16_t nb_tx = 0;
uint16_tnb_enqd;
unsigned intfifo_free;app/test-pmd/noisy_vnf.c +2
-2@@ -126,12 +133,12 @@ pkt_burst_noisy_vnf(struct fwd_stream *fs) bool needs_flush = false; uint64_t now; - nb_rx = common_fwd_stream_receive(fs, pkts_burst, nb_pkt_per_burst); if (unlikely(nb_rx == 0)) goto flush; if (!ncf->do_buffering) { - sim_memory_lookups(ncf, nb_rx); + if (ncf->do_sim) + sim_memory_lookups(ncf, nb_rx); nb_tx = common_fwd_stream_transmit(fs, pkts_burst, nb_rx);goto end;
}app/test-pmd/noisy_vnf.c +0
-0@@ -169,11 +176,61 @@ pkt_burst_noisy_vnf(struct fwd_stream *fs) ncf->prev_time = rte_get_timer_cycles(); }end:
+ returnnb_tx;app/test-pmd/noisy_vnf.c +10
-0+} + +static bool +pkt_burst_io (struct fwd_stream *fs) +{ + struct rte_mbuf *pkts_burst[MAX_PKT_BURST]; + uint16_t nb_rx; + uint16_t nb_tx; + + nb_rx = common_fwd_stream_receive(fs, pkts_burst,
nb_pkt_per_burst);
+nb_tx=noisy_eth_tx_burst(fs, nb_rx, pkts_burst); +
returnnb_rx> 0 ||nb_tx> 0;
}Quoted 14 lines
Quoted 11 lines
app/test-pmd/noisy_vnf.c +8
-2-#define NOISY_STRSIZE 256 -#define NOISY_RING "noisy_ring_%d\n" +static bool +pkt_burst_mac (struct fwd_stream *fs) +{ + struct rte_mbuf *pkts_burst[MAX_PKT_BURST]; + uint16_t nb_rx; + uint16_t nb_tx; + + nb_rx = common_fwd_stream_receive(fs, pkts_burst,
nb_pkt_per_burst);Similar to
macfwd.c, you can add check forunlikely(nb_rx == 0)at this point in these fns.That's true. I removed it because I'll have to call
noisy_eth_tx_burst()regardless, but we could avoid the middle call in these locations.I agree with the other suggestions.
Thanks,
MQuoted 197 lines
app/test-pmd/noisy_vnf.c pkt_burst_noisy_vnf(struct fwd_stream *fs) · line 213
Quoted 12 lines
+
do_macfwd(pkts_burst, nb_rx, fs);
+nb_tx=noisy_eth_tx_burst(fs, nb_rx, pkts_burst);app/test-pmd/noisy_vnf.c +9
-0+ + return nb_rx > 0 || nb_tx > 0; +} +static bool +pkt_burst_macswap (struct fwd_stream *fs) +{ + struct rte_mbuf *pkts_burst[MAX_PKT_BURST]; + uint16_t nb_rx = 0; + uint16_t nb_tx = 0;nit: these are not assigned in the other functions
Quoted 91 lines
+
+nb_rx=common_fwd_stream_receive(fs, pkts_burst, nb_pkt_per_burst);
+do_macswap(pkts_burst, nb_rx, &ports[fs->tx_port]); +nb_tx=noisy_eth_tx_burst(fs, nb_rx, pkts_burst);app/test-pmd/noisy_vnf.c +11
-0+ + return nb_rx > 0 || nb_tx > 0; +} +static bool +pkt_brust_5tswap (struct fwd_stream *fs) +{ + struct rte_mbuf *pkts_burst[MAX_PKT_BURST]; + uint16_t nb_rx = 0; + uint16_t nb_tx = 0; + + nb_rx = common_fwd_stream_receive(fs, pkts_burst,
nb_pkt_per_burst);
+do_5tswap(pkts_burst, nb_rx, fs);
+nb_tx=noisy_eth_tx_burst(fs, nb_rx, pkts_burst);app/test-pmd/noisy_vnf.c +3
-0+ + return nb_rx > 0 || nb_tx > 0; +}static void
noisy_fwd_end(portid_t pi)app/test-pmd/noisy_vnf.c +11
-2@@ -226,6 +283,15 @@ noisy_fwd_begin(portid_t pi) "--noisy-lkup-memory-size must be > 0\n"); } + if (noisy_fwd_mode == NOISY_FWD_MODE_IO) + noisy_vnf_engine.packet_fwd = pkt_burst_io; + else if (noisy_fwd_mode == NOISY_FWD_MODE_MAC) + noisy_vnf_engine.packet_fwd = pkt_burst_mac; + else if (noisy_fwd_mode == NOISY_FWD_MODE_MACSWAP) + noisy_vnf_engine.packet_fwd = pkt_burst_macswap; + else if (noisy_fwd_mode == NOISY_FWD_MODE_5TSWAP) + noisy_vnf_engine.packet_fwd = pkt_brust_5tswap; + return 0; }@@ -233,6 +299,6 @@ struct fwd_engine noisy_vnf_engine = { .fwd_mode_name = "noisy", .port_fwd_begin = noisy_fwd_begin, .port_fwd_end = noisy_fwd_end, - .stream_init = common_fwd_stream_init, - .packet_fwd = pkt_burst_noisy_vnf, + .stream_init = common_fwd_stream_init, + .packet_fwd = pkt_burst_io, };app/test-pmd/parameters.c +0
-0@@ -196,6 +196,7 @@ usage(char* progname)
printf(" --noisy-lkup-num-writes=N: do N random writes per packet\n");
printf(" --noisy-lkup-num-reads=N: do N random reads per packet\n");
printf(" --noisy-lkup-num-reads-writes=N: do N random reads and writes per packet\n");
+printf(" --noisy-fwd-mode=mode: set the fwd mode\n"); printf(" --no-iova-contig: mempool memory can be IOVA non contiguous. "
"valid only with --mp-alloc=anon\n"); printf(" --rx-mq-mode=0xX: hexadecimal bitmask of RX mq mode can be "app/test-pmd/parameters.c +1
-0@@ -704,6 +705,7 @@ launch_args_parse(int argc, char** argv) { "noisy-lkup-num-writes", 1, 0, 0 }, { "noisy-lkup-num-reads", 1, 0, 0 }, { "noisy-lkup-num-reads-writes", 1, 0, 0 }, + { "noisy-fwd-mode", 1, 0, 0 }, { "no-iova-contig", 0, 0, 0 }, { "rx-mq-mode", 1, 0, 0 }, { "record-core-cycles", 0, 0, 0 },@@ -1444,6 +1446,21 @@ launch_args_parse(int argc, char** argv) rte_exit(EXIT_FAILURE,
"noisy-lkup-num-reads-writes must be >= 0\n");
}
+ if (!strcmp(lgopts[opt_idx].name, + "noisy-fwd-mode")) { + if (!strcmp(optarg, "io")) +noisy_fwd_mode=NOISY_FWD_MODE_IO;
+ else if (!strcmp(optarg, "mac")) +noisy_fwd_mode=NOISY_FWD_MODE_MAC;
+ else if (!strcmp(optarg, "macswap")) +noisy_fwd_mode=NOISY_FWD_MODE_MACSWAP;Quoted 8 lines
+ else if (!strcmp(optarg, "5tswap")) +
noisy_fwd_mode=NOISY_FWD_MODE_5TSWAP;
+ else
+ rte_exit(EXIT_FAILURE, "noisy-fwd-mode %s invalid -"
+ " must b a valid fwd mode\n",typo "be"
I would specify "..must be a valid noisy-fwd-mode value" to avoid confusion with the full set of general fwd modes and easier for user to search them in docs.
Quoted 75 lines
+ optarg); + }
if (!strcmp(lgopts[opt_idx].name, "no-iova-contig"))
mempool_flags=RTE_MEMPOOL_F_NO_IOVA_CONTIG;app/test-pmd/testpmd.c +5
-0@@ -364,6 +364,11 @@ uint64_t noisy_lkup_num_reads;*/ uint64_t noisy_lkup_num_reads_writes; +/* +* Configurable forwarding mode in VNF simulation. +*/ +int noisy_fwd_mode; + /** Receive Side Scaling (RSS) configuration. */ app/test-pmd/testpmd.h +7
-0@@ -116,6 +116,13 @@ enum { QUEUE_JOB_TYPE_ACTION_QUERY, }; +enum { + NOISY_FWD_MODE_IO, + NOISY_FWD_MODE_MAC, + NOISY_FWD_MODE_MACSWAP, + NOISY_FWD_MODE_5TSWAP +}; + /*** The data structure associated with RX and TX packet burst statistics
* that are recorded for each forwarding stream.app/test-pmd/testpmd.h +1
-0@@ -561,6 +568,7 @@ extern uint64_t noisy_lkup_mem_sz; extern uint64_t noisy_lkup_num_writes; extern uint64_t noisy_lkup_num_reads; extern uint64_t noisy_lkup_num_reads_writes; +extern int noisy_fwd_mode; extern uint8_t dcb_config;doc/guides/testpmd_app_ug/run_app.rst +0
-0@@ -519,6 +519,15 @@ The command line options are:Set the number of r/w accesses to be done in noisy neighbor simulation memory buffer to N.
Only available with the noisy forwarding mode. The default value is 0.doc/guides/testpmd_app_ug/run_app.rst +3
-0+* ``--noisy-fwd-mode=mode`` + + Set the noisy vnf forwarding mode where ``mode`` is one of thefollowing::
doc/guides/testpmd_app_ug/run_app.rst +6
-0+ + io (the default) + mac + macswap + 5tswap +* ``--no-iova-contig``
Enable to create mempool which is not IOVA contiguous. Valid only with --mp-alloc=anon.
PATCH v4 1/1 app/testpmd: expand noisy neighbour forward mode support
In reply to Mike PattrickPreviously the noisy neighbour vnf simulation would only operate in io mode, forwarding packets as is. However, this limited the usefulness of noisy neighbour simulation.
This feature has now been expanded to supporting mac, macswap, and 5tswap modes. To facilitate adding this support, some new header files were added.
---
v2: Reverted changes to random memory lookup
v3: Refactored entire patch
v4: Implemented recommended formatting changes
--- app/test-pmd/5tswap.c | 118 +---------------------- app/test-pmd/5tswap.h | 130 ++++++++++++++++++++++++++ app/test-pmd/macfwd.c | 33 +------ app/test-pmd/macfwd.h | 45 +++++++++ app/test-pmd/macswap.h | 2 +- app/test-pmd/macswap_neon.h | 2 +- app/test-pmd/macswap_sse.h | 4 +- app/test-pmd/noisy_vnf.c | 106 +++++++++++++++++---- app/test-pmd/parameters.c | 17 ++++ app/test-pmd/testpmd.c | 5 + app/test-pmd/testpmd.h | 8 ++ doc/guides/testpmd_app_ug/run_app.rst | 9 ++ 12 files changed, 313 insertions(+), 166 deletions(-) create mode 100644 app/test-pmd/5tswap.h create mode 100644 app/test-pmd/macfwd.h
app/test-pmd/5tswap.c +3 -115
@@ -17,64 +17,8 @@#include <rte_ip.h> #include <rte_flow.h> -#include "macswap_common.h" #include "testpmd.h" - - -static inline void -swap_mac (struct rte_ether_hdr *eth_hdr) -{ -struct rte_ether_addr addr; - -/* Swap dest and src mac addresses. */ -rte_ether_addr_copy (ð_hdr->dst_addr, &addr); -rte_ether_addr_copy (ð_hdr->src_addr, ð_hdr->dst_addr); -rte_ether_addr_copy (&addr, ð_hdr->src_addr); -} - -static inline void -swap_ipv4 (struct rte_ipv4_hdr *ipv4_hdr) -{ -rte_be32_t addr; - -/* Swap dest and src ipv4 addresses. */ - addr = ipv4_hdr->src_addr; - ipv4_hdr->src_addr = ipv4_hdr->dst_addr; - ipv4_hdr->dst_addr = addr; -} - -static inline void -swap_ipv6 (struct rte_ipv6_hdr *ipv6_hdr) -{ -uint8_t addr[16 ]; - -/* Swap dest and src ipv6 addresses. */ -memcpy (&addr, &ipv6_hdr->src_addr,16 ); -memcpy (&ipv6_hdr->src_addr, &ipv6_hdr->dst_addr,16 ); -memcpy (&ipv6_hdr->dst_addr, &addr,16 ); -} - -static inline void -swap_tcp (struct rte_tcp_hdr *tcp_hdr) -{ -rte_be16_t port; - -/* Swap dest and src tcp port. */ - port = tcp_hdr->src_port; - tcp_hdr->src_port = tcp_hdr->dst_port; - tcp_hdr->dst_port = port; -} - -static inline void -swap_udp (struct rte_udp_hdr *udp_hdr) -{ -rte_be16_t port; - -/* Swap dest and src udp port */ - port = udp_hdr->src_port; - udp_hdr->src_port = udp_hdr->dst_port; - udp_hdr->dst_port = port; -} +#include "5tswap.h" /* * 5 tuple swap forwarding mode: Swap the source and the destination of layers
@@ -85,22 +29,7 @@ static bool pkt_burst_5tuple_swap(struct fwd_stream *fs) {struct rte_mbuf *pkts_burst[MAX_PKT_BURST ]; -struct rte_port *txp; -struct rte_mbuf *mb; -uint16_t next_proto; -uint64_t ol_flags; -uint16_t proto;uint16_t nb_rx; -int i; -union { -struct rte_ether_hdr *eth; -struct rte_vlan_hdr *vlan; -struct rte_ipv4_hdr *ipv4; -struct rte_ipv6_hdr *ipv6; -struct rte_tcp_hdr *tcp; -struct rte_udp_hdr *udp; -uint8_t *byte; - } h;/* * Receive a burst of packets and forward them.
@@ -109,49 +38,8 @@ pkt_burst_5tuple_swap(struct fwd_stream *fs)if (unlikely (nb_rx ==0 ))return false; - txp = &ports[fs->tx_port]; - ol_flags =ol_flags_init (txp->dev_conf.txmode.offloads); -vlan_qinq_set (pkts_burst, nb_rx, ol_flags, - txp->tx_vlan_id, txp->tx_vlan_id_outer); -for (i =0 ; i < nb_rx; i++) { -if (likely (i < nb_rx -1 )) -rte_prefetch0 (rte_pktmbuf_mtod (pkts_burst[i+1 ], - void *)); - mb = pkts_burst[i]; - h.eth = rte_pktmbuf_mtod(mb, struct rte_ether_hdr *); - proto = h.eth->ether_type; -swap_mac (h.eth); - mb->l2_len =sizeof (struct rte_ether_hdr ); - h.eth++; -while (proto ==RTE_BE16 (RTE_ETHER_TYPE_VLAN ) || - proto ==RTE_BE16 (RTE_ETHER_TYPE_QINQ )) { - proto = h.vlan->eth_proto; - h.vlan++; - mb->l2_len +=sizeof (struct rte_vlan_hdr ); - } -if (proto ==RTE_BE16 (RTE_ETHER_TYPE_IPV4 )) { -swap_ipv4 (h.ipv4); - next_proto = h.ipv4->next_proto_id; - mb->l3_len =rte_ipv4_hdr_len (h.ipv4); - h.byte += mb->l3_len; - }else if (proto ==RTE_BE16 (RTE_ETHER_TYPE_IPV6 )) { -swap_ipv6 (h.ipv6); - next_proto = h.ipv6->proto; - h.ipv6++; - mb->l3_len =sizeof (struct rte_ipv6_hdr ); - }else { -mbuf_field_set (mb, ol_flags); -continue ; - } -if (next_proto ==IPPROTO_UDP ) { -swap_udp (h.udp); - mb->l4_len =sizeof (struct rte_udp_hdr ); - }else if (next_proto ==IPPROTO_TCP ) { -swap_tcp (h.tcp); - mb->l4_len = (h.tcp->data_off &0xf0 ) >>2 ; - } -mbuf_field_set (mb, ol_flags); - } +do_5tswap (pkts_burst, nb_rx, fs); +common_fwd_stream_transmit (fs, pkts_burst, nb_rx);return true;
app/test-pmd/5tswap.h new file +130 -0
130 lines not on this page · raw message
app/test-pmd/macfwd.c +2 -31
@@ -35,6 +35,7 @@#include <rte_flow.h> #include "testpmd.h" +#include "macfwd.h" /* * Forwarding of packets in MAC mode.
@@ -45,13 +46,7 @@ static bool pkt_burst_mac_forward(struct fwd_stream *fs) {struct rte_mbuf *pkts_burst[MAX_PKT_BURST ]; -struct rte_port *txp; -struct rte_mbuf *mb; -struct rte_ether_hdr *eth_hdr;uint16_t nb_rx; -uint16_t i; -uint64_t ol_flags =0 ; -uint64_t tx_offloads;/* * Receive a burst of packets and forward them.
@@ -60,31 +55,7 @@ pkt_burst_mac_forward(struct fwd_stream *fs)if (unlikely (nb_rx ==0 ))return false; - txp = &ports[fs->tx_port]; - tx_offloads = txp->dev_conf.txmode.offloads; -if (tx_offloads &RTE_ETH_TX_OFFLOAD_VLAN_INSERT ) - ol_flags =RTE_MBUF_F_TX_VLAN ; -if (tx_offloads &RTE_ETH_TX_OFFLOAD_QINQ_INSERT ) - ol_flags |=RTE_MBUF_F_TX_QINQ ; -if (tx_offloads &RTE_ETH_TX_OFFLOAD_MACSEC_INSERT ) - ol_flags |=RTE_MBUF_F_TX_MACSEC ; -for (i =0 ; i < nb_rx; i++) { -if (likely (i < nb_rx -1 )) -rte_prefetch0 (rte_pktmbuf_mtod (pkts_burst[i +1 ], - void *)); - mb = pkts_burst[i]; - eth_hdr = rte_pktmbuf_mtod(mb, struct rte_ether_hdr *); -rte_ether_addr_copy (&peer_eth_addrs[fs->peer_addr], - ð_hdr->dst_addr); -rte_ether_addr_copy (&ports[fs->tx_port].eth_addr, - ð_hdr->src_addr); - mb->ol_flags &=RTE_MBUF_F_INDIRECT |RTE_MBUF_F_EXTERNAL ; - mb->ol_flags |= ol_flags; - mb->l2_len =sizeof (struct rte_ether_hdr ); - mb->l3_len =sizeof (struct rte_ipv4_hdr ); - mb->vlan_tci = txp->tx_vlan_id; - mb->vlan_tci_outer = txp->tx_vlan_id_outer; - } +do_macfwd (pkts_burst, nb_rx, fs);common_fwd_stream_transmit (fs, pkts_burst, nb_rx);
app/test-pmd/macfwd.h new file +45 -0
45 lines not on this page · raw message
app/test-pmd/macswap.h +1 -1
@@ -9,7 +9,7 @@static inline void do_macswap (struct rte_mbuf *pkts[],uint16_t nb, -struct rte_port *txp) +struct rte_port *txp) {struct rte_ether_hdr *eth_hdr;struct rte_mbuf *mb;
app/test-pmd/macswap_neon.h +1 -1
@@ -14,7 +14,7 @@static inline void do_macswap (struct rte_mbuf *pkts[],uint16_t nb, -struct rte_port *txp) +struct rte_port *txp) {struct rte_ether_hdr *eth_hdr[4 ];struct rte_mbuf *mb[4 ];
app/test-pmd/macswap_sse.h +2 -2
@@ -9,7 +9,7 @@static inline void do_macswap (struct rte_mbuf *pkts[],uint16_t nb, -struct rte_port *txp) +struct rte_port *txp) {struct rte_ether_hdr *eth_hdr[4 ];struct rte_mbuf *mb[4 ];
@@ -29,7 +29,7 @@ do_macswap(struct rte_mbuf *pkts[], uint16_t nb, ol_flags =ol_flags_init (txp->dev_conf.txmode.offloads);vlan_qinq_set (pkts, nb, ol_flags, - txp->tx_vlan_id, txp->tx_vlan_id_outer); + txp->tx_vlan_id, txp->tx_vlan_id_outer); i =0 ; r = nb;
app/test-pmd/noisy_vnf.c +90 -16
162 lines not on this page · raw message
app/test-pmd/parameters.c +17 -0
@@ -196,6 +196,7 @@ usage(char* progname)printf (" --noisy-lkup-num-writes=N: do N random writes per packet\n" );printf (" --noisy-lkup-num-reads=N: do N random reads per packet\n" );printf (" --noisy-lkup-num-reads-writes=N: do N random reads and writes per packet\n" ); +printf (" --noisy-fwd-mode=mode: set the fwd mode\n" );printf (" --no-iova-contig: mempool memory can be IOVA non contiguous. " "valid only with --mp-alloc=anon\n" ); printf(" --rx-mq-mode=0xX: hexadecimal bitmask of RX mq mode can be "
@@ -704,6 +705,7 @@ launch_args_parse(int argc, char** argv) { "noisy-lkup-num-writes", 1, 0, 0 }, { "noisy-lkup-num-reads", 1, 0, 0 }, { "noisy-lkup-num-reads-writes", 1, 0, 0 }, + { "noisy-fwd-mode", 1, 0, 0 }, { "no-iova-contig", 0, 0, 0 }, { "rx-mq-mode", 1, 0, 0 }, { "record-core-cycles", 0, 0, 0 },
@@ -1444,6 +1446,21 @@ launch_args_parse(int argc, char** argv)rte_exit (EXIT_FAILURE ,"noisy-lkup-num-reads-writes must be >= 0\n" ); } +if (!strcmp (lgopts[opt_idx].name, +"noisy-fwd-mode" )) { +if (!strcmp (optarg,"io" )) + noisy_fwd_mode =NOISY_FWD_MODE_IO ; +else if (!strcmp (optarg,"mac" )) + noisy_fwd_mode =NOISY_FWD_MODE_MAC ; +else if (!strcmp (optarg,"macswap" )) + noisy_fwd_mode =NOISY_FWD_MODE_MACSWAP ; +else if (!strcmp (optarg,"5tswap" )) + noisy_fwd_mode =NOISY_FWD_MODE_5TSWAP ; +else +rte_exit (EXIT_FAILURE ,"noisy-fwd-mode %s invalid -" +" must be a valid noisy-fwd-mode value\n" , + optarg); + }if (!strcmp (lgopts[opt_idx].name,"no-iova-contig" )) mempool_flags =RTE_MEMPOOL_F_NO_IOVA_CONTIG ;
app/test-pmd/testpmd.c +5 -0
@@ -364,6 +364,11 @@ uint64_t noisy_lkup_num_reads;*/ uint64_t noisy_lkup_num_reads_writes; +/* +* Configurable forwarding mode in VNF simulation. +*/ +int noisy_fwd_mode; +/* * Receive Side Scaling (RSS) configuration. */
app/test-pmd/testpmd.h +8 -0
@@ -116,6 +116,13 @@ enum { QUEUE_JOB_TYPE_ACTION_QUERY, }; +enum { +NOISY_FWD_MODE_IO , +NOISY_FWD_MODE_MAC , +NOISY_FWD_MODE_MACSWAP , +NOISY_FWD_MODE_5TSWAP +}; +/** * The data structure associated with RX and TX packet burst statistics * that are recorded for each forwarding stream.
@@ -561,6 +568,7 @@ extern uint64_t noisy_lkup_mem_sz;extern uint64_t noisy_lkup_num_writes;extern uint64_t noisy_lkup_num_reads;extern uint64_t noisy_lkup_num_reads_writes; +extern int noisy_fwd_mode;extern uint8_t dcb_config;
doc/guides/testpmd_app_ug/run_app.rst +9 -0
@@ -519,6 +519,15 @@ The command line options are: Set the number of r/w accesses to be done in noisy neighbor simulation memory buffer to N. Only available with the noisy forwarding mode. The default value is 0. +* ``--noisy-fwd-mode=mode`` + + Set the noisy vnf forwarding mode where ``mode`` is one of the following:: + + io (the default) + mac + macswap + 5tswap + * ``--no-iova-contig`` Enable to create mempool which is not IOVA contiguous. Valid only with --mp-alloc=anon.
Signature · 1 line
2.31.1
Quoted 182 lines · Mike Pattrick
Previously the noisy neighbour vnf simulation would only operate in io mode, forwarding packets as is. However, this limited the usefulness of noisy neighbour simulation.
This feature has now been expanded to supporting mac, macswap, and 5tswap modes. To facilitate adding this support, some new header files were added.
Signed-off-by Mike Pattrick <[email protected]>---
v2: Reverted changes to random memory lookup
v3: Refactored entire patch
v4: Implemented recommended formatting changes--- app/test-pmd/5tswap.c | 118 +---------------------- app/test-pmd/5tswap.h | 130 ++++++++++++++++++++++++++ app/test-pmd/macfwd.c | 33 +------ app/test-pmd/macfwd.h | 45 +++++++++ app/test-pmd/macswap.h | 2 +- app/test-pmd/macswap_neon.h | 2 +- app/test-pmd/macswap_sse.h | 4 +- app/test-pmd/noisy_vnf.c | 106 +++++++++++++++++---- app/test-pmd/parameters.c | 17 ++++ app/test-pmd/testpmd.c | 5 + app/test-pmd/testpmd.h | 8 ++ doc/guides/testpmd_app_ug/run_app.rst | 9 ++ 12 files changed, 313 insertions(+), 166 deletions(-) create mode 100644 app/test-pmd/5tswap.h create mode 100644 app/test-pmd/macfwd.happ/test-pmd/5tswap.c +3
-115@@ -17,64 +17,8 @@#include <rte_ip.h> #include <rte_flow.h> -#include "macswap_common.h" #include "testpmd.h" - - -static inline void -swap_mac (struct rte_ether_hdr *eth_hdr) -{ -struct rte_ether_addr addr; - -/* Swap dest and src mac addresses. */ -rte_ether_addr_copy (ð_hdr->dst_addr, &addr); -rte_ether_addr_copy (ð_hdr->src_addr, ð_hdr->dst_addr); -rte_ether_addr_copy (&addr, ð_hdr->src_addr); -} - -static inline void -swap_ipv4 (struct rte_ipv4_hdr *ipv4_hdr) -{ -rte_be32_t addr; - -/* Swap dest and src ipv4 addresses. */ - addr = ipv4_hdr->src_addr; - ipv4_hdr->src_addr = ipv4_hdr->dst_addr; - ipv4_hdr->dst_addr = addr; -} - -static inline void -swap_ipv6 (struct rte_ipv6_hdr *ipv6_hdr) -{ -uint8_t addr[16 ]; - -/* Swap dest and src ipv6 addresses. */ -memcpy (&addr, &ipv6_hdr->src_addr,16 ); -memcpy (&ipv6_hdr->src_addr, &ipv6_hdr->dst_addr,16 ); -memcpy (&ipv6_hdr->dst_addr, &addr,16 ); -} - -static inline void -swap_tcp (struct rte_tcp_hdr *tcp_hdr) -{ -rte_be16_t port; - -/* Swap dest and src tcp port. */ - port = tcp_hdr->src_port; - tcp_hdr->src_port = tcp_hdr->dst_port; - tcp_hdr->dst_port = port; -} - -static inline void -swap_udp (struct rte_udp_hdr *udp_hdr) -{ -rte_be16_t port; - -/* Swap dest and src udp port */ - port = udp_hdr->src_port; - udp_hdr->src_port = udp_hdr->dst_port; - udp_hdr->dst_port = port; -} +#include "5tswap.h" /* * 5 tuple swap forwarding mode: Swap the source and the destination of layers @@ -85,22 +29,7 @@ static bool pkt_burst_5tuple_swap(struct fwd_stream *fs) {struct rte_mbuf *pkts_burst[MAX_PKT_BURST ]; -struct rte_port *txp; -struct rte_mbuf *mb; -uint16_t next_proto; -uint64_t ol_flags; -uint16_t proto;uint16_t nb_rx; -int i; -union { -struct rte_ether_hdr *eth; -struct rte_vlan_hdr *vlan; -struct rte_ipv4_hdr *ipv4; -struct rte_ipv6_hdr *ipv6; -struct rte_tcp_hdr *tcp; -struct rte_udp_hdr *udp; -uint8_t *byte; - } h;/* * Receive a burst of packets and forward them. @@ -109,49 +38,8 @@ pkt_burst_5tuple_swap(struct fwd_stream *fs)if (unlikely (nb_rx ==0 ))return false; - txp = &ports[fs->tx_port]; - ol_flags =ol_flags_init (txp->dev_conf.txmode.offloads); -vlan_qinq_set (pkts_burst, nb_rx, ol_flags, - txp->tx_vlan_id, txp->tx_vlan_id_outer); -for (i =0 ; i < nb_rx; i++) { -if (likely (i < nb_rx -1 )) -rte_prefetch0 (rte_pktmbuf_mtod (pkts_burst[i+1 ], - void *)); - mb = pkts_burst[i]; - h.eth = rte_pktmbuf_mtod(mb, struct rte_ether_hdr *); - proto = h.eth->ether_type; -swap_mac (h.eth); - mb->l2_len =sizeof (struct rte_ether_hdr ); - h.eth++; -while (proto ==RTE_BE16 (RTE_ETHER_TYPE_VLAN ) || - proto ==RTE_BE16 (RTE_ETHER_TYPE_QINQ )) { - proto = h.vlan->eth_proto; - h.vlan++; - mb->l2_len +=sizeof (struct rte_vlan_hdr ); - } -if (proto ==RTE_BE16 (RTE_ETHER_TYPE_IPV4 )) { -swap_ipv4 (h.ipv4); - next_proto = h.ipv4->next_proto_id; - mb->l3_len =rte_ipv4_hdr_len (h.ipv4); - h.byte += mb->l3_len; - }else if (proto ==RTE_BE16 (RTE_ETHER_TYPE_IPV6 )) { -swap_ipv6 (h.ipv6); - next_proto = h.ipv6->proto; - h.ipv6++; - mb->l3_len =sizeof (struct rte_ipv6_hdr ); - }else { -mbuf_field_set (mb, ol_flags); -continue ; - } -if (next_proto ==IPPROTO_UDP ) { -swap_udp (h.udp); - mb->l4_len =sizeof (struct rte_udp_hdr ); - }else if (next_proto ==IPPROTO_TCP ) { -swap_tcp (h.tcp); - mb->l4_len = (h.tcp->data_off &0xf0 ) >>2 ; - } -mbuf_field_set (mb, ol_flags); - } +do_5tswap (pkts_burst, nb_rx, fs); +common_fwd_stream_transmit (fs, pkts_burst, nb_rx);return true;app/test-pmd/5tswap.h new file +0
-0
app/test-pmd/5tswap.h line 2
Quoted 2 lines
app/test-pmd/5tswap.h new file +2
-0@@ -0,0 +1,130 @@ +/* SPDX-License-Identifier: BSD-3-Clause +* Copyright(c) 2018 Intel Corporation
I guess intention is to keep original file copyright owner, but it is not Intel, can you please check again?
Quoted 278 lines
app/test-pmd/5tswap.h new file +128
-0+*/ + +#ifndef _5TSWAP_H_ +#define _5TSWAP_H_ + +#include "macswap_common.h" + +static inline void +swap_mac (struct rte_ether_hdr *eth_hdr) +{ +struct rte_ether_addr addr; + +/* Swap dest and src mac addresses. */ +rte_ether_addr_copy (ð_hdr->dst_addr, &addr); +rte_ether_addr_copy (ð_hdr->src_addr, ð_hdr->dst_addr); +rte_ether_addr_copy (&addr, ð_hdr->src_addr); +} + +static inline void +swap_ipv4 (struct rte_ipv4_hdr *ipv4_hdr) +{ +rte_be32_t addr; + +/* Swap dest and src ipv4 addresses. */ + addr = ipv4_hdr->src_addr; + ipv4_hdr->src_addr = ipv4_hdr->dst_addr; + ipv4_hdr->dst_addr = addr; +} + +static inline void +swap_ipv6 (struct rte_ipv6_hdr *ipv6_hdr) +{ +uint8_t addr[16 ]; + +/* Swap dest and src ipv6 addresses. */ +memcpy (&addr, &ipv6_hdr->src_addr,16 ); +memcpy (&ipv6_hdr->src_addr, &ipv6_hdr->dst_addr,16 ); +memcpy (&ipv6_hdr->dst_addr, &addr,16 ); +} + +static inline void +swap_tcp (struct rte_tcp_hdr *tcp_hdr) +{ +rte_be16_t port; + +/* Swap dest and src tcp port. */ + port = tcp_hdr->src_port; + tcp_hdr->src_port = tcp_hdr->dst_port; + tcp_hdr->dst_port = port; +} + +static inline void +swap_udp (struct rte_udp_hdr *udp_hdr) +{ +rte_be16_t port; + +/* Swap dest and src udp port */ + port = udp_hdr->src_port; + udp_hdr->src_port = udp_hdr->dst_port; + udp_hdr->dst_port = port; +} + +static inline void +do_5tswap (struct rte_mbuf *pkts_burst[],uint16_t nb_rx, +struct fwd_stream *fs) +{ +struct rte_port *txp; +struct rte_mbuf *mb; +uint16_t next_proto; +uint64_t ol_flags; +uint16_t proto; +int i; +union { +struct rte_ether_hdr *eth; +struct rte_vlan_hdr *vlan; +struct rte_ipv4_hdr *ipv4; +struct rte_ipv6_hdr *ipv6; +struct rte_tcp_hdr *tcp; +struct rte_udp_hdr *udp; +uint8_t *byte; + } h; + + txp = &ports[fs->tx_port]; + ol_flags =ol_flags_init (txp->dev_conf.txmode.offloads); +vlan_qinq_set (pkts_burst, nb_rx, ol_flags, + txp->tx_vlan_id, txp->tx_vlan_id_outer); +for (i =0 ; i < nb_rx; i++) { +if (likely (i < nb_rx -1 )) +rte_prefetch0 (rte_pktmbuf_mtod (pkts_burst[i+1 ], + void *)); + mb = pkts_burst[i]; + h.eth = rte_pktmbuf_mtod(mb, struct rte_ether_hdr *); + proto = h.eth->ether_type; +swap_mac (h.eth); + mb->l2_len =sizeof (struct rte_ether_hdr ); + h.eth++; +while (proto ==RTE_BE16 (RTE_ETHER_TYPE_VLAN ) || + proto ==RTE_BE16 (RTE_ETHER_TYPE_QINQ )) { + proto = h.vlan->eth_proto; + h.vlan++; + mb->l2_len +=sizeof (struct rte_vlan_hdr ); + } +if (proto ==RTE_BE16 (RTE_ETHER_TYPE_IPV4 )) { +swap_ipv4 (h.ipv4); + next_proto = h.ipv4->next_proto_id; + mb->l3_len =rte_ipv4_hdr_len (h.ipv4); + h.byte += mb->l3_len; + }else if (proto ==RTE_BE16 (RTE_ETHER_TYPE_IPV6 )) { +swap_ipv6 (h.ipv6); + next_proto = h.ipv6->proto; + h.ipv6++; + mb->l3_len =sizeof (struct rte_ipv6_hdr ); + }else { +mbuf_field_set (mb, ol_flags); +continue ; + } +if (next_proto ==IPPROTO_UDP ) { +swap_udp (h.udp); + mb->l4_len =sizeof (struct rte_udp_hdr ); + }else if (next_proto ==IPPROTO_TCP ) { +swap_tcp (h.tcp); + mb->l4_len = (h.tcp->data_off &0xf0 ) >>2 ; + } +mbuf_field_set (mb, ol_flags); + } +} + +#endif /* _5TSWAP_H_ */ app/test-pmd/macfwd.c +2
-31@@ -35,6 +35,7 @@#include <rte_flow.h> #include "testpmd.h" +#include "macfwd.h" /* * Forwarding of packets in MAC mode. @@ -45,13 +46,7 @@ static bool pkt_burst_mac_forward(struct fwd_stream *fs) {struct rte_mbuf *pkts_burst[MAX_PKT_BURST ]; -struct rte_port *txp; -struct rte_mbuf *mb; -struct rte_ether_hdr *eth_hdr;uint16_t nb_rx; -uint16_t i; -uint64_t ol_flags =0 ; -uint64_t tx_offloads;/* * Receive a burst of packets and forward them. @@ -60,31 +55,7 @@ pkt_burst_mac_forward(struct fwd_stream *fs)if (unlikely (nb_rx ==0 ))return false; - txp = &ports[fs->tx_port]; - tx_offloads = txp->dev_conf.txmode.offloads; -if (tx_offloads &RTE_ETH_TX_OFFLOAD_VLAN_INSERT ) - ol_flags =RTE_MBUF_F_TX_VLAN ; -if (tx_offloads &RTE_ETH_TX_OFFLOAD_QINQ_INSERT ) - ol_flags |=RTE_MBUF_F_TX_QINQ ; -if (tx_offloads &RTE_ETH_TX_OFFLOAD_MACSEC_INSERT ) - ol_flags |=RTE_MBUF_F_TX_MACSEC ; -for (i =0 ; i < nb_rx; i++) { -if (likely (i < nb_rx -1 )) -rte_prefetch0 (rte_pktmbuf_mtod (pkts_burst[i +1 ], - void *)); - mb = pkts_burst[i]; - eth_hdr = rte_pktmbuf_mtod(mb, struct rte_ether_hdr *); -rte_ether_addr_copy (&peer_eth_addrs[fs->peer_addr], - ð_hdr->dst_addr); -rte_ether_addr_copy (&ports[fs->tx_port].eth_addr, - ð_hdr->src_addr); - mb->ol_flags &=RTE_MBUF_F_INDIRECT |RTE_MBUF_F_EXTERNAL ; - mb->ol_flags |= ol_flags; - mb->l2_len =sizeof (struct rte_ether_hdr ); - mb->l3_len =sizeof (struct rte_ipv4_hdr ); - mb->vlan_tci = txp->tx_vlan_id; - mb->vlan_tci_outer = txp->tx_vlan_id_outer; - } +do_macfwd (pkts_burst, nb_rx, fs);common_fwd_stream_transmit (fs, pkts_burst, nb_rx);app/test-pmd/macfwd.h new file +45
-0@@ -0,0 +1,45 @@ +/* SPDX-License-Identifier: BSD-3-Clause +* Copyright(c) 2018 Intel Corporation +*/ + +#ifndef _MACFWD_H_ +#define _MACFWD_H_ + +static inline void +do_macfwd (struct rte_mbuf *pkts_burst[],uint16_t nb_rx, +struct fwd_stream *fs) +{ +struct rte_ether_hdr *eth_hdr; +uint64_t ol_flags =0 ; +uint64_t tx_offloads; +struct rte_mbuf *mb; +struct rte_port *txp = &ports[fs->tx_port]; +uint16_t i; + + tx_offloads = txp->dev_conf.txmode.offloads; +if (tx_offloads &RTE_ETH_TX_OFFLOAD_VLAN_INSERT ) + ol_flags =RTE_MBUF_F_TX_VLAN ; +if (tx_offloads &RTE_ETH_TX_OFFLOAD_QINQ_INSERT ) + ol_flags |=RTE_MBUF_F_TX_QINQ ; +if (tx_offloads &RTE_ETH_TX_OFFLOAD_MACSEC_INSERT ) + ol_flags |=RTE_MBUF_F_TX_MACSEC ; +for (i =0 ; i < nb_rx; i++) { +if (likely (i < nb_rx -1 )) +rte_prefetch0 (rte_pktmbuf_mtod (pkts_burst[i +1 ], + void *)); + mb = pkts_burst[i]; + eth_hdr = rte_pktmbuf_mtod(mb, struct rte_ether_hdr *); +rte_ether_addr_copy (&peer_eth_addrs[fs->peer_addr], + ð_hdr->dst_addr); +rte_ether_addr_copy (&ports[fs->tx_port].eth_addr, + ð_hdr->src_addr); + mb->ol_flags &=RTE_MBUF_F_INDIRECT |RTE_MBUF_F_EXTERNAL ; + mb->ol_flags |= ol_flags; + mb->l2_len =sizeof (struct rte_ether_hdr ); + mb->l3_len =sizeof (struct rte_ipv4_hdr ); + mb->vlan_tci = txp->tx_vlan_id; + mb->vlan_tci_outer = txp->tx_vlan_id_outer; + } +} + +#endif /* _MACFWD_H_ */ app/test-pmd/macswap.h +1
-1@@ -9,7 +9,7 @@static inline void do_macswap (struct rte_mbuf *pkts[],uint16_t nb, -struct rte_port *txp) +struct rte_port *txp) {struct rte_ether_hdr *eth_hdr;struct rte_mbuf *mb;app/test-pmd/macswap_neon.h +1
-1@@ -14,7 +14,7 @@static inline void do_macswap (struct rte_mbuf *pkts[],uint16_t nb, -struct rte_port *txp) +struct rte_port *txp) {struct rte_ether_hdr *eth_hdr[4 ];struct rte_mbuf *mb[4 ];app/test-pmd/macswap_sse.h +1
-1@@ -9,7 +9,7 @@static inline void do_macswap (struct rte_mbuf *pkts[],uint16_t nb, -struct rte_port *txp) +struct rte_port *txp) {struct rte_ether_hdr *eth_hdr[4 ];struct rte_mbuf *mb[4 ];
app/test-pmd/macswap_sse.h do_macswap(struct rte_mbuf *pkts[], uint16_t nb, · line 35
Quoted 8 lines
app/test-pmd/macswap_sse.h +1
-1@@ -29,7 +29,7 @@ do_macswap(struct rte_mbuf *pkts[], uint16_t nb, ol_flags =ol_flags_init (txp->dev_conf.txmode.offloads);vlan_qinq_set (pkts, nb, ol_flags, - txp->tx_vlan_id, txp->tx_vlan_id_outer); + txp->tx_vlan_id, txp->tx_vlan_id_outer); i =0 ; r = nb;
Can you please remove these syntax changes, they are not just noise for this patch?
And indeed original syntax looks correct, DPDK coding convention doesn't allign parameters to the paranthesis, but uses tabs for next line.
Quoted 179 lines
app/test-pmd/noisy_vnf.c +90
-16@@ -32,6 +32,18 @@#include <rte_malloc.h> #include "testpmd.h" +#include "5tswap.h" +#include "macfwd.h" +#if defined(RTE_ARCH_X86 ) +#include "macswap_sse.h" +#elif defined(__ARM_NEON) +#include "macswap_neon.h" +#else +#include "macswap.h" +#endif + +#define NOISY_STRSIZE 256 +#define NOISY_RING "noisy_ring_%d\n"struct noisy_config {struct rte_ring *f;@@ -80,9 +92,6 @@ sim_memory_lookups(struct noisy_config *ncf, uint16_t nb_pkts) {uint16_t i, j; -if (!ncf->do_sim) -return ; -for (i =0 ; i < nb_pkts; i++) {for (j =0 ; j < noisy_lkup_num_writes; j++)do_write (ncf->vnf_mem);@@ -110,15 +119,13 @@ sim_memory_lookups(struct noisy_config *ncf, uint16_t nb_pkts)* out of the FIFO * 4. Cases 2 and 3 combined */ -static bool -pkt_burst_noisy_vnf (struct fwd_stream *fs) +static uint16_t +noisy_eth_tx_burst (struct fwd_stream *fs,uint16_t nb_rx,struct rte_mbuf **pkts_burst) {const uint64_t freq_khz =rte_get_timer_hz () /1000 ;struct noisy_config *ncf = noisy_cfg[fs->rx_port]; -struct rte_mbuf *pkts_burst[MAX_PKT_BURST ];struct rte_mbuf *tmp_pkts[MAX_PKT_BURST ];uint16_t nb_deqd =0 ; -uint16_t nb_rx =0 ;uint16_t nb_tx =0 ;uint16_t nb_enqd;unsigned int fifo_free;@@ -126,12 +133,16 @@ pkt_burst_noisy_vnf(struct fwd_stream *fs)bool needs_flush = false;uint64_t now; - nb_rx =common_fwd_stream_receive (fs, pkts_burst, nb_pkt_per_burst); -if (unlikely (nb_rx ==0 )) - goto flush; +if (unlikely (nb_rx ==0 )) { +if (!ncf->do_buffering) + goto end; +else + goto flush; + }if (!ncf->do_buffering) { -sim_memory_lookups (ncf, nb_rx); +if (ncf->do_sim) +sim_memory_lookups (ncf, nb_rx); nb_tx =common_fwd_stream_transmit (fs, pkts_burst, nb_rx); goto end; }@@ -150,7 +161,8 @@ pkt_burst_noisy_vnf(struct fwd_stream *fs) nb_tx =common_fwd_stream_transmit (fs, tmp_pkts, nb_deqd); } -sim_memory_lookups (ncf, nb_enqd); +if (ncf->do_sim) +sim_memory_lookups (ncf, nb_enqd); flush:if (ncf->do_flush) {@@ -169,11 +181,64 @@ pkt_burst_noisy_vnf(struct fwd_stream *fs) ncf->prev_time =rte_get_timer_cycles (); } end: +return nb_tx; +} + +static bool +pkt_burst_io (struct fwd_stream *fs) +{ +struct rte_mbuf *pkts_burst[MAX_PKT_BURST ]; +uint16_t nb_rx; +uint16_t nb_tx; + + nb_rx =common_fwd_stream_receive (fs, pkts_burst, nb_pkt_per_burst); + nb_tx =noisy_eth_tx_burst (fs, nb_rx, pkts_burst); +return nb_rx >0 || nb_tx >0 ; } -#define NOISY_STRSIZE 256 -#define NOISY_RING "noisy_ring_%d\n" +static bool +pkt_burst_mac (struct fwd_stream *fs) +{ +struct rte_mbuf *pkts_burst[MAX_PKT_BURST ]; +uint16_t nb_rx; +uint16_t nb_tx; + + nb_rx =common_fwd_stream_receive (fs, pkts_burst, nb_pkt_per_burst); +if (likely (nb_rx !=0 )) +do_macfwd (pkts_burst, nb_rx, fs); + nb_tx =noisy_eth_tx_burst (fs, nb_rx, pkts_burst); + +return nb_rx >0 || nb_tx >0 ; +} +static bool +pkt_burst_macswap (struct fwd_stream *fs) +{ +struct rte_mbuf *pkts_burst[MAX_PKT_BURST ]; +uint16_t nb_rx; +uint16_t nb_tx; + + nb_rx =common_fwd_stream_receive (fs, pkts_burst, nb_pkt_per_burst); +if (likely (nb_rx !=0 )) +do_macswap (pkts_burst, nb_rx, &ports[fs->tx_port]); + nb_tx =noisy_eth_tx_burst (fs, nb_rx, pkts_burst); + +return nb_rx >0 || nb_tx >0 ; +} +static bool +pkt_brust_5tswap (struct fwd_stream *fs) +{ +struct rte_mbuf *pkts_burst[MAX_PKT_BURST ]; +uint16_t nb_rx; +uint16_t nb_tx; + + nb_rx =common_fwd_stream_receive (fs, pkts_burst, nb_pkt_per_burst); +if (likely (nb_rx !=0 )) +do_5tswap (pkts_burst, nb_rx, fs); + nb_tx =noisy_eth_tx_burst (fs, nb_rx, pkts_burst); + +return nb_rx >0 || nb_tx >0 ; +}static void noisy_fwd_end (portid_t pi)@@ -226,6 +291,15 @@ noisy_fwd_begin(portid_t pi) "--noisy-lkup-memory-size must be > 0\n"); } +if (noisy_fwd_mode ==NOISY_FWD_MODE_IO ) + noisy_vnf_engine.packet_fwd = pkt_burst_io; +else if (noisy_fwd_mode ==NOISY_FWD_MODE_MAC ) + noisy_vnf_engine.packet_fwd = pkt_burst_mac; +else if (noisy_fwd_mode ==NOISY_FWD_MODE_MACSWAP ) + noisy_vnf_engine.packet_fwd = pkt_burst_macswap; +else if (noisy_fwd_mode ==NOISY_FWD_MODE_5TSWAP ) + noisy_vnf_engine.packet_fwd = pkt_brust_5tswap; +return 0 ; }@@ -233,6 +307,6 @@ struct fwd_engine noisy_vnf_engine = { .fwd_mode_name = "noisy", .port_fwd_begin = noisy_fwd_begin, .port_fwd_end = noisy_fwd_end, - .stream_init = common_fwd_stream_init, - .packet_fwd = pkt_burst_noisy_vnf, + .stream_init = common_fwd_stream_init, + .packet_fwd = pkt_burst_io, };app/test-pmd/parameters.c +0
-0
app/test-pmd/parameters.c usage(char* progname) · line 199
Quoted 4 lines
app/test-pmd/parameters.c +1
-0@@ -196,6 +196,7 @@ usage(char* progname)printf (" --noisy-lkup-num-writes=N: do N random writes per packet\n" );printf (" --noisy-lkup-num-reads=N: do N random reads per packet\n" );printf (" --noisy-lkup-num-reads-writes=N: do N random reads and writes per packet\n" ); +printf (" --noisy-fwd-mode=mode: set the fwd mode\n" );
'--noisy-fwd-mode' looks more major config option comparing the other '--noisy-lkup-*' ones, if so can you please move '--noisy-fwd-mode' up to the top of the '--noisy-*' group?
Also what do you think to list possible values here, to help users, like 'io (default), mac, macswap, 5tswap'.
Quoted 38 lines
app/test-pmd/parameters.c +16
-0printf (" --no-iova-contig: mempool memory can be IOVA non contiguous. " "valid only with --mp-alloc=anon\n" ); printf(" --rx-mq-mode=0xX: hexadecimal bitmask of RX mq mode can be "@@ -704,6 +705,7 @@ launch_args_parse(int argc, char** argv) { "noisy-lkup-num-writes", 1, 0, 0 }, { "noisy-lkup-num-reads", 1, 0, 0 }, { "noisy-lkup-num-reads-writes", 1, 0, 0 }, + { "noisy-fwd-mode", 1, 0, 0 }, { "no-iova-contig", 0, 0, 0 }, { "rx-mq-mode", 1, 0, 0 }, { "record-core-cycles", 0, 0, 0 },@@ -1444,6 +1446,21 @@ launch_args_parse(int argc, char** argv)rte_exit (EXIT_FAILURE ,"noisy-lkup-num-reads-writes must be >= 0\n" ); } +if (!strcmp (lgopts[opt_idx].name, +"noisy-fwd-mode" )) { +if (!strcmp (optarg,"io" )) + noisy_fwd_mode =NOISY_FWD_MODE_IO ; +else if (!strcmp (optarg,"mac" )) + noisy_fwd_mode =NOISY_FWD_MODE_MAC ; +else if (!strcmp (optarg,"macswap" )) + noisy_fwd_mode =NOISY_FWD_MODE_MACSWAP ; +else if (!strcmp (optarg,"5tswap" )) + noisy_fwd_mode =NOISY_FWD_MODE_5TSWAP ; +else +rte_exit (EXIT_FAILURE ,"noisy-fwd-mode %s invalid -" +" must be a valid noisy-fwd-mode value\n" , + optarg); + }if (!strcmp (lgopts[opt_idx].name,"no-iova-contig" )) mempool_flags =RTE_MEMPOOL_F_NO_IOVA_CONTIG ;app/test-pmd/testpmd.c +0
-0
app/test-pmd/testpmd.c uint64_t noisy_lkup_num_reads; · line 368
Quoted 5 lines
app/test-pmd/testpmd.c +2
-0@@ -364,6 +364,11 @@ uint64_t noisy_lkup_num_reads;*/ uint64_t noisy_lkup_num_reads_writes; +/* +* Configurable forwarding mode in VNF simulation.
Kind of obvious from variable name but can you extend the comment to give more detail that this is related to the noisy forwarding mode?
app/test-pmd/testpmd.c uint64_t noisy_lkup_num_reads; · line 371
Quoted 3 lines
app/test-pmd/testpmd.c +3
-0+*/ +int noisy_fwd_mode; +
Why not define named enum and use it here, instead of 'int'?
Quoted 49 lines
app/test-pmd/testpmd.c +0
-0/* * Receive Side Scaling (RSS) configuration. */ app/test-pmd/testpmd.h +8
-0@@ -116,6 +116,13 @@ enum { QUEUE_JOB_TYPE_ACTION_QUERY, }; +enum { +NOISY_FWD_MODE_IO , +NOISY_FWD_MODE_MAC , +NOISY_FWD_MODE_MACSWAP , +NOISY_FWD_MODE_5TSWAP +}; +/** * The data structure associated with RX and TX packet burst statistics * that are recorded for each forwarding stream. @@ -561,6 +568,7 @@ extern uint64_t noisy_lkup_mem_sz;extern uint64_t noisy_lkup_num_writes;extern uint64_t noisy_lkup_num_reads;extern uint64_t noisy_lkup_num_reads_writes; +extern int noisy_fwd_mode;extern uint8_t dcb_config;doc/guides/testpmd_app_ug/run_app.rst +9
-0@@ -519,6 +519,15 @@ The command line options are: Set the number of r/w accesses to be done in noisy neighbor simulation memory buffer to N. Only available with the noisy forwarding mode. The default value is 0. +* ``--noisy-fwd-mode=mode`` + + Set the noisy vnf forwarding mode where ``mode`` is one of the following:: + + io (the default) + mac + macswap + 5tswap + * ``--no-iova-contig`` Enable to create mempool which is not IOVA contiguous. Valid only with --mp-alloc=anon.
PATCH v5 1/1 app/testpmd: expand noisy neighbour forward mode support
In reply to Mike PattrickPreviously the noisy neighbour vnf simulation would only operate in io mode, forwarding packets as is. However, this limited the usefulness of noisy neighbour simulation.
This feature has now been expanded to supporting mac, macswap, and 5tswap modes. To facilitate adding this support, some new header files were added.
---
v2: Reverted changes to random memory lookup
v3: Refactored entire patch
v4: Implemented recommended formatting changes
v5: Corrected copyright statement and formatting changes
--- app/test-pmd/5tswap.c | 118 +---------------------- app/test-pmd/5tswap.h | 130 ++++++++++++++++++++++++++ app/test-pmd/macfwd.c | 33 +------ app/test-pmd/macfwd.h | 45 +++++++++ app/test-pmd/noisy_vnf.c | 106 +++++++++++++++++---- app/test-pmd/parameters.c | 17 ++++ app/test-pmd/testpmd.c | 5 + app/test-pmd/testpmd.h | 8 ++ doc/guides/testpmd_app_ug/run_app.rst | 9 ++ 9 files changed, 309 insertions(+), 162 deletions(-) create mode 100644 app/test-pmd/5tswap.h create mode 100644 app/test-pmd/macfwd.h
app/test-pmd/5tswap.c +3 -115
@@ -17,64 +17,8 @@#include <rte_ip.h> #include <rte_flow.h> -#include "macswap_common.h" #include "testpmd.h" - - -static inline void -swap_mac (struct rte_ether_hdr *eth_hdr) -{ -struct rte_ether_addr addr; - -/* Swap dest and src mac addresses. */ -rte_ether_addr_copy (ð_hdr->dst_addr, &addr); -rte_ether_addr_copy (ð_hdr->src_addr, ð_hdr->dst_addr); -rte_ether_addr_copy (&addr, ð_hdr->src_addr); -} - -static inline void -swap_ipv4 (struct rte_ipv4_hdr *ipv4_hdr) -{ -rte_be32_t addr; - -/* Swap dest and src ipv4 addresses. */ - addr = ipv4_hdr->src_addr; - ipv4_hdr->src_addr = ipv4_hdr->dst_addr; - ipv4_hdr->dst_addr = addr; -} - -static inline void -swap_ipv6 (struct rte_ipv6_hdr *ipv6_hdr) -{ -uint8_t addr[16 ]; - -/* Swap dest and src ipv6 addresses. */ -memcpy (&addr, &ipv6_hdr->src_addr,16 ); -memcpy (&ipv6_hdr->src_addr, &ipv6_hdr->dst_addr,16 ); -memcpy (&ipv6_hdr->dst_addr, &addr,16 ); -} - -static inline void -swap_tcp (struct rte_tcp_hdr *tcp_hdr) -{ -rte_be16_t port; - -/* Swap dest and src tcp port. */ - port = tcp_hdr->src_port; - tcp_hdr->src_port = tcp_hdr->dst_port; - tcp_hdr->dst_port = port; -} - -static inline void -swap_udp (struct rte_udp_hdr *udp_hdr) -{ -rte_be16_t port; - -/* Swap dest and src udp port */ - port = udp_hdr->src_port; - udp_hdr->src_port = udp_hdr->dst_port; - udp_hdr->dst_port = port; -} +#include "5tswap.h" /* * 5 tuple swap forwarding mode: Swap the source and the destination of layers
@@ -85,22 +29,7 @@ static bool pkt_burst_5tuple_swap(struct fwd_stream *fs) {struct rte_mbuf *pkts_burst[MAX_PKT_BURST ]; -struct rte_port *txp; -struct rte_mbuf *mb; -uint16_t next_proto; -uint64_t ol_flags; -uint16_t proto;uint16_t nb_rx; -int i; -union { -struct rte_ether_hdr *eth; -struct rte_vlan_hdr *vlan; -struct rte_ipv4_hdr *ipv4; -struct rte_ipv6_hdr *ipv6; -struct rte_tcp_hdr *tcp; -struct rte_udp_hdr *udp; -uint8_t *byte; - } h;/* * Receive a burst of packets and forward them.
@@ -109,49 +38,8 @@ pkt_burst_5tuple_swap(struct fwd_stream *fs)if (unlikely (nb_rx ==0 ))return false; - txp = &ports[fs->tx_port]; - ol_flags =ol_flags_init (txp->dev_conf.txmode.offloads); -vlan_qinq_set (pkts_burst, nb_rx, ol_flags, - txp->tx_vlan_id, txp->tx_vlan_id_outer); -for (i =0 ; i < nb_rx; i++) { -if (likely (i < nb_rx -1 )) -rte_prefetch0 (rte_pktmbuf_mtod (pkts_burst[i+1 ], - void *)); - mb = pkts_burst[i]; - h.eth = rte_pktmbuf_mtod(mb, struct rte_ether_hdr *); - proto = h.eth->ether_type; -swap_mac (h.eth); - mb->l2_len =sizeof (struct rte_ether_hdr ); - h.eth++; -while (proto ==RTE_BE16 (RTE_ETHER_TYPE_VLAN ) || - proto ==RTE_BE16 (RTE_ETHER_TYPE_QINQ )) { - proto = h.vlan->eth_proto; - h.vlan++; - mb->l2_len +=sizeof (struct rte_vlan_hdr ); - } -if (proto ==RTE_BE16 (RTE_ETHER_TYPE_IPV4 )) { -swap_ipv4 (h.ipv4); - next_proto = h.ipv4->next_proto_id; - mb->l3_len =rte_ipv4_hdr_len (h.ipv4); - h.byte += mb->l3_len; - }else if (proto ==RTE_BE16 (RTE_ETHER_TYPE_IPV6 )) { -swap_ipv6 (h.ipv6); - next_proto = h.ipv6->proto; - h.ipv6++; - mb->l3_len =sizeof (struct rte_ipv6_hdr ); - }else { -mbuf_field_set (mb, ol_flags); -continue ; - } -if (next_proto ==IPPROTO_UDP ) { -swap_udp (h.udp); - mb->l4_len =sizeof (struct rte_udp_hdr ); - }else if (next_proto ==IPPROTO_TCP ) { -swap_tcp (h.tcp); - mb->l4_len = (h.tcp->data_off &0xf0 ) >>2 ; - } -mbuf_field_set (mb, ol_flags); - } +do_5tswap (pkts_burst, nb_rx, fs); +common_fwd_stream_transmit (fs, pkts_burst, nb_rx);return true;
app/test-pmd/5tswap.h new file +130 -0
130 lines not on this page · raw message
app/test-pmd/macfwd.c +2 -31
@@ -35,6 +35,7 @@#include <rte_flow.h> #include "testpmd.h" +#include "macfwd.h" /* * Forwarding of packets in MAC mode.
@@ -45,13 +46,7 @@ static bool pkt_burst_mac_forward(struct fwd_stream *fs) {struct rte_mbuf *pkts_burst[MAX_PKT_BURST ]; -struct rte_port *txp; -struct rte_mbuf *mb; -struct rte_ether_hdr *eth_hdr;uint16_t nb_rx; -uint16_t i; -uint64_t ol_flags =0 ; -uint64_t tx_offloads;/* * Receive a burst of packets and forward them.
@@ -60,31 +55,7 @@ pkt_burst_mac_forward(struct fwd_stream *fs)if (unlikely (nb_rx ==0 ))return false; - txp = &ports[fs->tx_port]; - tx_offloads = txp->dev_conf.txmode.offloads; -if (tx_offloads &RTE_ETH_TX_OFFLOAD_VLAN_INSERT ) - ol_flags =RTE_MBUF_F_TX_VLAN ; -if (tx_offloads &RTE_ETH_TX_OFFLOAD_QINQ_INSERT ) - ol_flags |=RTE_MBUF_F_TX_QINQ ; -if (tx_offloads &RTE_ETH_TX_OFFLOAD_MACSEC_INSERT ) - ol_flags |=RTE_MBUF_F_TX_MACSEC ; -for (i =0 ; i < nb_rx; i++) { -if (likely (i < nb_rx -1 )) -rte_prefetch0 (rte_pktmbuf_mtod (pkts_burst[i +1 ], - void *)); - mb = pkts_burst[i]; - eth_hdr = rte_pktmbuf_mtod(mb, struct rte_ether_hdr *); -rte_ether_addr_copy (&peer_eth_addrs[fs->peer_addr], - ð_hdr->dst_addr); -rte_ether_addr_copy (&ports[fs->tx_port].eth_addr, - ð_hdr->src_addr); - mb->ol_flags &=RTE_MBUF_F_INDIRECT |RTE_MBUF_F_EXTERNAL ; - mb->ol_flags |= ol_flags; - mb->l2_len =sizeof (struct rte_ether_hdr ); - mb->l3_len =sizeof (struct rte_ipv4_hdr ); - mb->vlan_tci = txp->tx_vlan_id; - mb->vlan_tci_outer = txp->tx_vlan_id_outer; - } +do_macfwd (pkts_burst, nb_rx, fs);common_fwd_stream_transmit (fs, pkts_burst, nb_rx);
app/test-pmd/macfwd.h new file +45 -0
45 lines not on this page · raw message
app/test-pmd/noisy_vnf.c +90 -16
162 lines not on this page · raw message
app/test-pmd/parameters.c +17 -0
@@ -190,6 +190,7 @@ usage(char* progname)" anon: use regular DPDK memory to create and anonymous memory to populate mempool\n" " xmem: use anonymous memory to create and populate mempool\n" " xmemhuge: use anonymous hugepage memory to create and populate mempool\n"); +printf (" --noisy-fwd-mode=<io|mac|macswap|5tswap>: set the sub-fwd mode, defaults to io\n" );printf (" --noisy-tx-sw-buffer-size=N: size of FIFO buffer\n" );printf (" --noisy-tx-sw-buffer-flushtime=N: flush FIFO after N ms\n" );printf (" --noisy-lkup-memory=N: allocate N MB of VNF memory\n" );
@@ -704,6 +705,7 @@ launch_args_parse(int argc, char** argv) { "noisy-lkup-num-writes", 1, 0, 0 }, { "noisy-lkup-num-reads", 1, 0, 0 }, { "noisy-lkup-num-reads-writes", 1, 0, 0 }, + { "noisy-fwd-mode", 1, 0, 0 }, { "no-iova-contig", 0, 0, 0 }, { "rx-mq-mode", 1, 0, 0 }, { "record-core-cycles", 0, 0, 0 },
@@ -1444,6 +1446,21 @@ launch_args_parse(int argc, char** argv)rte_exit (EXIT_FAILURE ,"noisy-lkup-num-reads-writes must be >= 0\n" ); } +if (!strcmp (lgopts[opt_idx].name, +"noisy-fwd-mode" )) { +if (!strcmp (optarg,"io" )) + noisy_fwd_mode =NOISY_FWD_MODE_IO ; +else if (!strcmp (optarg,"mac" )) + noisy_fwd_mode =NOISY_FWD_MODE_MAC ; +else if (!strcmp (optarg,"macswap" )) + noisy_fwd_mode =NOISY_FWD_MODE_MACSWAP ; +else if (!strcmp (optarg,"5tswap" )) + noisy_fwd_mode =NOISY_FWD_MODE_5TSWAP ; +else +rte_exit (EXIT_FAILURE ,"noisy-fwd-mode %s invalid -" +" must be a valid noisy-fwd-mode value\n" , + optarg); + }if (!strcmp (lgopts[opt_idx].name,"no-iova-contig" )) mempool_flags =RTE_MEMPOOL_F_NO_IOVA_CONTIG ;
app/test-pmd/testpmd.c +5 -0
@@ -364,6 +364,11 @@ uint64_t noisy_lkup_num_reads;*/ uint64_t noisy_lkup_num_reads_writes; +/* +* Configurable sub-forwarding mode for the noisy_vnf forwarding mode. +*/ +enum noisy_fwd_mode noisy_fwd_mode; +/* * Receive Side Scaling (RSS) configuration. */
app/test-pmd/testpmd.h +8 -0
@@ -116,6 +116,13 @@ enum { QUEUE_JOB_TYPE_ACTION_QUERY, }; +enum noisy_fwd_mode { +NOISY_FWD_MODE_IO , +NOISY_FWD_MODE_MAC , +NOISY_FWD_MODE_MACSWAP , +NOISY_FWD_MODE_5TSWAP +}; +/** * The data structure associated with RX and TX packet burst statistics * that are recorded for each forwarding stream.
@@ -561,6 +568,7 @@ extern uint64_t noisy_lkup_mem_sz;extern uint64_t noisy_lkup_num_writes;extern uint64_t noisy_lkup_num_reads;extern uint64_t noisy_lkup_num_reads_writes; +extern enum noisy_fwd_mode noisy_fwd_mode;extern uint8_t dcb_config;
doc/guides/testpmd_app_ug/run_app.rst +9 -0
@@ -519,6 +519,15 @@ The command line options are: Set the number of r/w accesses to be done in noisy neighbor simulation memory buffer to N. Only available with the noisy forwarding mode. The default value is 0. +* ``--noisy-fwd-mode=mode`` + + Set the noisy vnf forwarding mode where ``mode`` is one of the following:: + + io (the default) + mac + macswap + 5tswap + * ``--no-iova-contig`` Enable to create mempool which is not IOVA contiguous. Valid only with --mp-alloc=anon.
Signature · 1 line
2.31.1
Quoted 8 lines · Mike Pattrick
Previously the noisy neighbour vnf simulation would only operate in io mode, forwarding packets as is. However, this limited the usefulness of noisy neighbour simulation.
This feature has now been expanded to supporting mac, macswap, and 5tswap modes. To facilitate adding this support, some new header files were added.
Quoted 7 lines
Signed-off-by Mike Pattrick <[email protected]>---
v2: Reverted changes to random memory lookup
v3: Refactored entire patch
v4: Implemented recommended formatting changes
v5: Corrected copyright statement and formatting changes
Hi Mike,
There are some comments in v4 seems missed, can you please check the comments?
Quoted 17 lines · Ferruh Yigit
Quoted 8 lines · Mike Pattrick
Previously the noisy neighbour vnf simulation would only operate in io mode, forwarding packets as is. However, this limited the usefulness of noisy neighbour simulation.
This feature has now been expanded to supporting mac, macswap, and 5tswap modes. To facilitate adding this support, some new header files were added.
Quoted 7 lines
Signed-off-by Mike Pattrick <[email protected]>---
v2: Reverted changes to random memory lookup
v3: Refactored entire patch
v4: Implemented recommended formatting changes
v5: Corrected copyright statement and formatting changes
Quoted 5 lines
Hi Mike,
There are some comments in v4 seems missed, can you please check the comments?
My bad, v5 looks good, I was looking to wrong places, let me review/check this version.
Quoted 14 lines · Mike Pattrick
Previously the noisy neighbour vnf simulation would only operate in io mode, forwarding packets as is. However, this limited the usefulness of noisy neighbour simulation.
This feature has now been expanded to supporting mac, macswap, and 5tswap modes. To facilitate adding this support, some new header files were added.
Signed-off-by Mike Pattrick <[email protected]>---
v2: Reverted changes to random memory lookup
v3: Refactored entire patch
v4: Implemented recommended formatting changes
v5: Corrected copyright statement and formatting changes
<...>
app/test-pmd/noisy_vnf.c noisy_fwd_begin(portid_t pi) · line 302
Quoted 13 lines
app/test-pmd/noisy_vnf.c +9
-0@@ -226,6 +291,15 @@ noisy_fwd_begin(portid_t pi) "--noisy-lkup-memory-size must be > 0\n"); } +if (noisy_fwd_mode ==NOISY_FWD_MODE_IO ) + noisy_vnf_engine.packet_fwd = pkt_burst_io; +else if (noisy_fwd_mode ==NOISY_FWD_MODE_MAC ) + noisy_vnf_engine.packet_fwd = pkt_burst_mac; +else if (noisy_fwd_mode ==NOISY_FWD_MODE_MACSWAP ) + noisy_vnf_engine.packet_fwd = pkt_burst_macswap; +else if (noisy_fwd_mode ==NOISY_FWD_MODE_5TSWAP ) + noisy_vnf_engine.packet_fwd = pkt_brust_5tswap; +
When noisy forward mode is set, it is not possbile to see what mode is set, what about keeping '.fwd_mode_name' longer,
like "noisy - ", and update it based on selected mode?
This way "show config fwd" command displays selected noisy mode.
Quoted 17 lines
app/test-pmd/noisy_vnf.c +2
-2return 0 ; }@@ -233,6 +307,6 @@ struct fwd_engine noisy_vnf_engine = { .fwd_mode_name = "noisy", .port_fwd_begin = noisy_fwd_begin, .port_fwd_end = noisy_fwd_end, - .stream_init = common_fwd_stream_init, - .packet_fwd = pkt_burst_noisy_vnf, + .stream_init = common_fwd_stream_init, + .packet_fwd = pkt_burst_io, };app/test-pmd/parameters.c +0
-0
app/test-pmd/parameters.c usage(char* progname) · line 193
Quoted 4 lines
app/test-pmd/parameters.c +1
-0@@ -190,6 +190,7 @@ usage(char* progname)" anon: use regular DPDK memory to create and anonymous memory to populate mempool\n" " xmem: use anonymous memory to create and populate mempool\n" " xmemhuge: use anonymous hugepage memory to create and populate mempool\n"); +printf (" --noisy-fwd-mode=<io|mac|macswap|5tswap>: set the sub-fwd mode, defaults to io\n" );
Main forwarding parameter is '--forward-mode=N', and while testing I searched for 'forward' in the testpmd help output but not able to find this command, because of shortened 'fwd'.
What do you think to have full '--noisy-forward-mode' to be more consistent with existing '--forward-mode=N'?
app/test-pmd/parameters.c launch_args_parse(int argc, char** argv) · line 708
Quoted 8 lines
app/test-pmd/parameters.c +1
-0printf (" --noisy-tx-sw-buffer-size=N: size of FIFO buffer\n" );printf (" --noisy-tx-sw-buffer-flushtime=N: flush FIFO after N ms\n" );printf (" --noisy-lkup-memory=N: allocate N MB of VNF memory\n" );@@ -704,6 +705,7 @@ launch_args_parse(int argc, char** argv) { "noisy-lkup-num-writes", 1, 0, 0 }, { "noisy-lkup-num-reads", 1, 0, 0 }, { "noisy-lkup-num-reads-writes", 1, 0, 0 }, + { "noisy-fwd-mode", 1, 0, 0 },
If there will be a new version can you please move it to the top of the noisy-* block, as done in the help string?
And this is same for all new code, from 'extern' to global variable to .rst documentation update.
Quoted 69 lines · Ferruh Yigit
Quoted 14 lines · Mike Pattrick
Previously the noisy neighbour vnf simulation would only operate in io mode, forwarding packets as is. However, this limited the usefulness of noisy neighbour simulation.
This feature has now been expanded to supporting mac, macswap, and 5tswap modes. To facilitate adding this support, some new header files were added.
Signed-off-by Mike Pattrick <[email protected]>---
v2: Reverted changes to random memory lookup
v3: Refactored entire patch
v4: Implemented recommended formatting changes
v5: Corrected copyright statement and formatting changes<...>
app/test-pmd/noisy_vnf.c noisy_fwd_begin(portid_t pi) · line 302
Quoted 13 lines
app/test-pmd/noisy_vnf.c +9
-0@@ -226,6 +291,15 @@ noisy_fwd_begin(portid_t pi) "--noisy-lkup-memory-size must be > 0\n"); } +if (noisy_fwd_mode ==NOISY_FWD_MODE_IO ) + noisy_vnf_engine.packet_fwd = pkt_burst_io; +else if (noisy_fwd_mode ==NOISY_FWD_MODE_MAC ) + noisy_vnf_engine.packet_fwd = pkt_burst_mac; +else if (noisy_fwd_mode ==NOISY_FWD_MODE_MACSWAP ) + noisy_vnf_engine.packet_fwd = pkt_burst_macswap; +else if (noisy_fwd_mode ==NOISY_FWD_MODE_5TSWAP ) + noisy_vnf_engine.packet_fwd = pkt_brust_5tswap; +When noisy forward mode is set, it is not possbile to see what mode is set, what about keeping '.fwd_mode_name' longer,
like "noisy - ", and update it based on selected mode?This way "show config fwd" command displays selected noisy mode.
Quoted 17 lines
app/test-pmd/noisy_vnf.c +2
-2return 0 ; }@@ -233,6 +307,6 @@ struct fwd_engine noisy_vnf_engine = { .fwd_mode_name = "noisy", .port_fwd_begin = noisy_fwd_begin, .port_fwd_end = noisy_fwd_end, - .stream_init = common_fwd_stream_init, - .packet_fwd = pkt_burst_noisy_vnf, + .stream_init = common_fwd_stream_init, + .packet_fwd = pkt_burst_io, };app/test-pmd/parameters.c +0
-0app/test-pmd/parameters.c usage(char* progname) · line 193
Quoted 4 lines
app/test-pmd/parameters.c +1
-0@@ -190,6 +190,7 @@ usage(char* progname)" anon: use regular DPDK memory to create and anonymous memory to populate mempool\n" " xmem: use anonymous memory to create and populate mempool\n" " xmemhuge: use anonymous hugepage memory to create and populate mempool\n"); +printf (" --noisy-fwd-mode=<io|mac|macswap|5tswap>: set the sub-fwd mode, defaults to io\n" );Main forwarding parameter is '--forward-mode=N', and while testing I searched for 'forward' in the testpmd help output but not able to find this command, because of shortened 'fwd'.
What do you think to have full '--noisy-forward-mode' to be more consistent with existing '--forward-mode=N'?
Quoted 13 lines
app/test-pmd/parameters.c launch_args_parse(int argc, char** argv) · line 708
Quoted 8 lines
app/test-pmd/parameters.c +1
-0printf (" --noisy-tx-sw-buffer-size=N: size of FIFO buffer\n" );printf (" --noisy-tx-sw-buffer-flushtime=N: flush FIFO after N ms\n" );printf (" --noisy-lkup-memory=N: allocate N MB of VNF memory\n" );@@ -704,6 +705,7 @@ launch_args_parse(int argc, char** argv) { "noisy-lkup-num-writes", 1, 0, 0 }, { "noisy-lkup-num-reads", 1, 0, 0 }, { "noisy-lkup-num-reads-writes", 1, 0, 0 }, + { "noisy-fwd-mode", 1, 0, 0 },If there will be a new version can you please move it to the top of the noisy-* block, as done in the help string?
And this is same for all new code, from 'extern' to global variable to .rst documentation update.
You've made some good suggestions here, I'll send you a new version.
Thanks for the review,
M
Quoted 1 line
PATCH v6 1/1 app/testpmd: expand noisy neighbour forward mode support
In reply to Mike PattrickPreviously the noisy neighbour vnf simulation would only operate in io mode, forwarding packets as is. However, this limited the usefulness of noisy neighbour simulation.
This feature has now been expanded to supporting mac, macswap, and 5tswap modes. To facilitate adding this support, some new header files were added.
---
v2: Reverted changes to random memory lookup
v3: Refactored entire patch
v4: Implemented recommended formatting changes
v5: Corrected copyright statement and formatting changes
v6: Reordered some variables, preserved noisy subtype for display
--- app/test-pmd/5tswap.c | 118 +---------------------- app/test-pmd/5tswap.h | 130 ++++++++++++++++++++++++++ app/test-pmd/config.c | 18 +++- app/test-pmd/macfwd.c | 33 +------ app/test-pmd/macfwd.h | 45 +++++++++ app/test-pmd/noisy_vnf.c | 106 +++++++++++++++++---- app/test-pmd/parameters.c | 15 +++ app/test-pmd/testpmd.c | 14 +++ app/test-pmd/testpmd.h | 10 ++ doc/guides/testpmd_app_ug/run_app.rst | 9 ++ 10 files changed, 334 insertions(+), 164 deletions(-) create mode 100644 app/test-pmd/5tswap.h create mode 100644 app/test-pmd/macfwd.h
app/test-pmd/5tswap.c +3 -115
@@ -17,64 +17,8 @@#include <rte_ip.h> #include <rte_flow.h> -#include "macswap_common.h" #include "testpmd.h" - - -static inline void -swap_mac (struct rte_ether_hdr *eth_hdr) -{ -struct rte_ether_addr addr; - -/* Swap dest and src mac addresses. */ -rte_ether_addr_copy (ð_hdr->dst_addr, &addr); -rte_ether_addr_copy (ð_hdr->src_addr, ð_hdr->dst_addr); -rte_ether_addr_copy (&addr, ð_hdr->src_addr); -} - -static inline void -swap_ipv4 (struct rte_ipv4_hdr *ipv4_hdr) -{ -rte_be32_t addr; - -/* Swap dest and src ipv4 addresses. */ - addr = ipv4_hdr->src_addr; - ipv4_hdr->src_addr = ipv4_hdr->dst_addr; - ipv4_hdr->dst_addr = addr; -} - -static inline void -swap_ipv6 (struct rte_ipv6_hdr *ipv6_hdr) -{ -uint8_t addr[16 ]; - -/* Swap dest and src ipv6 addresses. */ -memcpy (&addr, &ipv6_hdr->src_addr,16 ); -memcpy (&ipv6_hdr->src_addr, &ipv6_hdr->dst_addr,16 ); -memcpy (&ipv6_hdr->dst_addr, &addr,16 ); -} - -static inline void -swap_tcp (struct rte_tcp_hdr *tcp_hdr) -{ -rte_be16_t port; - -/* Swap dest and src tcp port. */ - port = tcp_hdr->src_port; - tcp_hdr->src_port = tcp_hdr->dst_port; - tcp_hdr->dst_port = port; -} - -static inline void -swap_udp (struct rte_udp_hdr *udp_hdr) -{ -rte_be16_t port; - -/* Swap dest and src udp port */ - port = udp_hdr->src_port; - udp_hdr->src_port = udp_hdr->dst_port; - udp_hdr->dst_port = port; -} +#include "5tswap.h" /* * 5 tuple swap forwarding mode: Swap the source and the destination of layers
@@ -85,22 +29,7 @@ static bool pkt_burst_5tuple_swap(struct fwd_stream *fs) {struct rte_mbuf *pkts_burst[MAX_PKT_BURST ]; -struct rte_port *txp; -struct rte_mbuf *mb; -uint16_t next_proto; -uint64_t ol_flags; -uint16_t proto;uint16_t nb_rx; -int i; -union { -struct rte_ether_hdr *eth; -struct rte_vlan_hdr *vlan; -struct rte_ipv4_hdr *ipv4; -struct rte_ipv6_hdr *ipv6; -struct rte_tcp_hdr *tcp; -struct rte_udp_hdr *udp; -uint8_t *byte; - } h;/* * Receive a burst of packets and forward them.
@@ -109,49 +38,8 @@ pkt_burst_5tuple_swap(struct fwd_stream *fs)if (unlikely (nb_rx ==0 ))return false; - txp = &ports[fs->tx_port]; - ol_flags =ol_flags_init (txp->dev_conf.txmode.offloads); -vlan_qinq_set (pkts_burst, nb_rx, ol_flags, - txp->tx_vlan_id, txp->tx_vlan_id_outer); -for (i =0 ; i < nb_rx; i++) { -if (likely (i < nb_rx -1 )) -rte_prefetch0 (rte_pktmbuf_mtod (pkts_burst[i+1 ], - void *)); - mb = pkts_burst[i]; - h.eth = rte_pktmbuf_mtod(mb, struct rte_ether_hdr *); - proto = h.eth->ether_type; -swap_mac (h.eth); - mb->l2_len =sizeof (struct rte_ether_hdr ); - h.eth++; -while (proto ==RTE_BE16 (RTE_ETHER_TYPE_VLAN ) || - proto ==RTE_BE16 (RTE_ETHER_TYPE_QINQ )) { - proto = h.vlan->eth_proto; - h.vlan++; - mb->l2_len +=sizeof (struct rte_vlan_hdr ); - } -if (proto ==RTE_BE16 (RTE_ETHER_TYPE_IPV4 )) { -swap_ipv4 (h.ipv4); - next_proto = h.ipv4->next_proto_id; - mb->l3_len =rte_ipv4_hdr_len (h.ipv4); - h.byte += mb->l3_len; - }else if (proto ==RTE_BE16 (RTE_ETHER_TYPE_IPV6 )) { -swap_ipv6 (h.ipv6); - next_proto = h.ipv6->proto; - h.ipv6++; - mb->l3_len =sizeof (struct rte_ipv6_hdr ); - }else { -mbuf_field_set (mb, ol_flags); -continue ; - } -if (next_proto ==IPPROTO_UDP ) { -swap_udp (h.udp); - mb->l4_len =sizeof (struct rte_udp_hdr ); - }else if (next_proto ==IPPROTO_TCP ) { -swap_tcp (h.tcp); - mb->l4_len = (h.tcp->data_off &0xf0 ) >>2 ; - } -mbuf_field_set (mb, ol_flags); - } +do_5tswap (pkts_burst, nb_rx, fs); +common_fwd_stream_transmit (fs, pkts_burst, nb_rx);return true;
app/test-pmd/5tswap.h new file +130 -0
130 lines not on this page · raw message
app/test-pmd/config.c +16 -2
@@ -4052,9 +4052,16 @@ rxtx_config_display(void) {portid_t pid;queueid_t qid; +char buf[32 ]; + +if (cur_fwd_eng == &noisy_vnf_engine) +snprintf (buf,sizeof (buf)," (%s)" , noisy_fwd_mode_desc[noisy_fwd_mode]); +else + buf[0 ] ='\0' ; -printf (" %s packet forwarding%s packets/burst=%d\n" , +printf (" %s%s packet forwarding%s packets/burst=%d\n" , cur_fwd_eng->fwd_mode_name, + buf, retry_enabled ==0 ?"" :" with retry" , nb_pkt_per_burst);
@@ -4816,10 +4823,17 @@ pkt_fwd_config_display(struct fwd_config *cfg)struct fwd_stream *fs;lcoreid_t lc_id;streamid_t sm_id; +char buf[32 ]; + +if (cfg->fwd_eng == &noisy_vnf_engine) +snprintf (buf,sizeof (buf)," (%s)" , noisy_fwd_mode_desc[noisy_fwd_mode]); +else + buf[0 ] ='\0' ; - printf("%s packet forwarding%s - ports=%d - cores=%d - streams=%d - " + printf("%s%s packet forwarding%s - ports=%d - cores=%d - streams=%d - " "NUMA support %s, MP allocation mode: %s\n", cfg->fwd_eng->fwd_mode_name, + buf, retry_enabled == 0 ? "" : " with retry", cfg->nb_fwd_ports, cfg->nb_fwd_lcores, cfg->nb_fwd_streams, numa_support == 1 ? "enabled" : "disabled",
app/test-pmd/macfwd.c +2 -31
@@ -35,6 +35,7 @@#include <rte_flow.h> #include "testpmd.h" +#include "macfwd.h" /* * Forwarding of packets in MAC mode.
@@ -45,13 +46,7 @@ static bool pkt_burst_mac_forward(struct fwd_stream *fs) {struct rte_mbuf *pkts_burst[MAX_PKT_BURST ]; -struct rte_port *txp; -struct rte_mbuf *mb; -struct rte_ether_hdr *eth_hdr;uint16_t nb_rx; -uint16_t i; -uint64_t ol_flags =0 ; -uint64_t tx_offloads;/* * Receive a burst of packets and forward them.
@@ -60,31 +55,7 @@ pkt_burst_mac_forward(struct fwd_stream *fs)if (unlikely (nb_rx ==0 ))return false; - txp = &ports[fs->tx_port]; - tx_offloads = txp->dev_conf.txmode.offloads; -if (tx_offloads &RTE_ETH_TX_OFFLOAD_VLAN_INSERT ) - ol_flags =RTE_MBUF_F_TX_VLAN ; -if (tx_offloads &RTE_ETH_TX_OFFLOAD_QINQ_INSERT ) - ol_flags |=RTE_MBUF_F_TX_QINQ ; -if (tx_offloads &RTE_ETH_TX_OFFLOAD_MACSEC_INSERT ) - ol_flags |=RTE_MBUF_F_TX_MACSEC ; -for (i =0 ; i < nb_rx; i++) { -if (likely (i < nb_rx -1 )) -rte_prefetch0 (rte_pktmbuf_mtod (pkts_burst[i +1 ], - void *)); - mb = pkts_burst[i]; - eth_hdr = rte_pktmbuf_mtod(mb, struct rte_ether_hdr *); -rte_ether_addr_copy (&peer_eth_addrs[fs->peer_addr], - ð_hdr->dst_addr); -rte_ether_addr_copy (&ports[fs->tx_port].eth_addr, - ð_hdr->src_addr); - mb->ol_flags &=RTE_MBUF_F_INDIRECT |RTE_MBUF_F_EXTERNAL ; - mb->ol_flags |= ol_flags; - mb->l2_len =sizeof (struct rte_ether_hdr ); - mb->l3_len =sizeof (struct rte_ipv4_hdr ); - mb->vlan_tci = txp->tx_vlan_id; - mb->vlan_tci_outer = txp->tx_vlan_id_outer; - } +do_macfwd (pkts_burst, nb_rx, fs);common_fwd_stream_transmit (fs, pkts_burst, nb_rx);
app/test-pmd/macfwd.h new file +45 -0
45 lines not on this page · raw message
app/test-pmd/noisy_vnf.c +90 -16
162 lines not on this page · raw message
app/test-pmd/parameters.c +15 -0
@@ -190,6 +190,7 @@ usage(char* progname)" anon: use regular DPDK memory to create and anonymous memory to populate mempool\n" " xmem: use anonymous memory to create and populate mempool\n" " xmemhuge: use anonymous hugepage memory to create and populate mempool\n"); +printf (" --noisy-forward-mode=<io|mac|macswap|5tswap>: set the sub-fwd mode, defaults to io\n" );printf (" --noisy-tx-sw-buffer-size=N: size of FIFO buffer\n" );printf (" --noisy-tx-sw-buffer-flushtime=N: flush FIFO after N ms\n" );printf (" --noisy-lkup-memory=N: allocate N MB of VNF memory\n" );
@@ -698,6 +699,7 @@ launch_args_parse(int argc, char** argv) { "mp-alloc", 1, 0, 0 }, { "tx-ip", 1, 0, 0 }, { "tx-udp", 1, 0, 0 }, + { "noisy-forward-mode", 1, 0, 0 }, { "noisy-tx-sw-buffer-size", 1, 0, 0 }, { "noisy-tx-sw-buffer-flushtime", 1, 0, 0 }, { "noisy-lkup-memory", 1, 0, 0 },
@@ -1444,6 +1446,19 @@ launch_args_parse(int argc, char** argv)rte_exit (EXIT_FAILURE ,"noisy-lkup-num-reads-writes must be >= 0\n" ); } +if (!strcmp (lgopts[opt_idx].name, +"noisy-forward-mode" )) { +int i; +for (i =0 ; i <NOISY_FWD_MODE_MAX ; i++) +if (!strcmp (optarg, noisy_fwd_mode_desc[i])) { + noisy_fwd_mode = i; +break ; + } +if (i ==NOISY_FWD_MODE_MAX ) +rte_exit (EXIT_FAILURE ,"noisy-forward-mode %s invalid," +" must be a valid noisy-forward-mode value\n" , + optarg); + }if (!strcmp (lgopts[opt_idx].name,"no-iova-contig" )) mempool_flags =RTE_MEMPOOL_F_NO_IOVA_CONTIG ;
app/test-pmd/testpmd.c +14 -0
@@ -330,6 +330,20 @@ int16_t tx_free_thresh = RTE_PMD_PARAM_UNSET;*/ int16_t tx_rs_thresh =RTE_PMD_PARAM_UNSET ; +/* +* Configurable sub-forwarding mode for the noisy_vnf forwarding mode. +*/ +enum noisy_fwd_mode noisy_fwd_mode; + +/* String version of enum noisy_fwd_mode */ +const char *const noisy_fwd_mode_desc[] = { + [NOISY_FWD_MODE_IO ] ="io" , + [NOISY_FWD_MODE_MAC ] ="mac" , + [NOISY_FWD_MODE_MACSWAP ] ="macswap" , + [NOISY_FWD_MODE_5TSWAP ] ="5tswap" , + [NOISY_FWD_MODE_MAX ] =NULL , +}; +/* * Configurable value of buffered packets before sending. */
app/test-pmd/testpmd.h +10 -0
@@ -116,6 +116,14 @@ enum { QUEUE_JOB_TYPE_ACTION_QUERY, }; +enum noisy_fwd_mode { +NOISY_FWD_MODE_IO , +NOISY_FWD_MODE_MAC , +NOISY_FWD_MODE_MACSWAP , +NOISY_FWD_MODE_5TSWAP , +NOISY_FWD_MODE_MAX , +}; +/** * The data structure associated with RX and TX packet burst statistics * that are recorded for each forwarding stream.
@@ -555,6 +563,8 @@ extern int8_t rx_drop_en;extern int16_t tx_free_thresh;extern int16_t tx_rs_thresh; +extern enum noisy_fwd_mode noisy_fwd_mode; +extern const char *const noisy_fwd_mode_desc[];extern uint16_t noisy_tx_sw_bufsz;extern uint16_t noisy_tx_sw_buf_flush_time;extern uint64_t noisy_lkup_mem_sz;
doc/guides/testpmd_app_ug/run_app.rst +9 -0
@@ -487,6 +487,15 @@ The command line options are: * xmemhuge: create and populate mempool using externally and anonymously allocated hugepage area +* ``--noisy-forward-mode=mode`` + + Set the noisy vnf forwarding mode where ``mode`` is one of the following:: + + io (the default) + mac + macswap + 5tswap + * ``--noisy-tx-sw-buffer-size`` Set the number of maximum elements of the FIFO queue to be created
Signature · 1 line
2.31.1
Quoted 30 lines · Mike Pattrick
Previously the noisy neighbour vnf simulation would only operate in io mode, forwarding packets as is. However, this limited the usefulness of noisy neighbour simulation.
This feature has now been expanded to supporting mac, macswap, and 5tswap modes. To facilitate adding this support, some new header files were added.
Signed-off-by Mike Pattrick <[email protected]>---
v2: Reverted changes to random memory lookup
v3: Refactored entire patch
v4: Implemented recommended formatting changes
v5: Corrected copyright statement and formatting changes
v6: Reordered some variables, preserved noisy subtype for display--- app/test-pmd/5tswap.c | 118 +---------------------- app/test-pmd/5tswap.h | 130 ++++++++++++++++++++++++++ app/test-pmd/config.c | 18 +++- app/test-pmd/macfwd.c | 33 +------ app/test-pmd/macfwd.h | 45 +++++++++ app/test-pmd/noisy_vnf.c | 106 +++++++++++++++++---- app/test-pmd/parameters.c | 15 +++ app/test-pmd/testpmd.c | 14 +++ app/test-pmd/testpmd.h | 10 ++ doc/guides/testpmd_app_ug/run_app.rst | 9 ++ 10 files changed, 334 insertions(+), 164 deletions(-) create mode 100644 app/test-pmd/5tswap.h create mode 100644 app/test-pmd/macfwd.h
<...>
Quoted 31 lines
app/test-pmd/config.c +13
-1@@ -4052,9 +4052,16 @@ rxtx_config_display(void) {portid_t pid;queueid_t qid; +char buf[32 ]; + +if (cur_fwd_eng == &noisy_vnf_engine) +snprintf (buf,sizeof (buf)," (%s)" , noisy_fwd_mode_desc[noisy_fwd_mode]); +else + buf[0 ] ='\0' ; -printf (" %s packet forwarding%s packets/burst=%d\n" , +printf (" %s%s packet forwarding%s packets/burst=%d\n" , cur_fwd_eng->fwd_mode_name, + buf, retry_enabled ==0 ?"" :" with retry" , nb_pkt_per_burst);@@ -4816,10 +4823,17 @@ pkt_fwd_config_display(struct fwd_config *cfg)struct fwd_stream *fs;lcoreid_t lc_id;streamid_t sm_id; +char buf[32 ]; + +if (cfg->fwd_eng == &noisy_vnf_engine) +snprintf (buf,sizeof (buf)," (%s)" , noisy_fwd_mode_desc[noisy_fwd_mode]); +else
app/test-pmd/config.c pkt_fwd_config_display(struct fwd_config *cfg) · line 4839
Quoted 10 lines
app/test-pmd/config.c +3
-1+ buf[0 ] ='\0' ; - printf("%s packet forwarding%s - ports=%d - cores=%d - streams=%d - " + printf("%s%s packet forwarding%s - ports=%d - cores=%d - streams=%d - " "NUMA support %s, MP allocation mode: %s\n", cfg->fwd_eng->fwd_mode_name, + buf, retry_enabled == 0 ? "" : " with retry", cfg->nb_fwd_ports, cfg->nb_fwd_lcores, cfg->nb_fwd_streams, numa_support == 1 ? "enabled" : "disabled",
This works but I wonder if we can keep the display functions generic (as much as possible), without forwarding enginee specific checks.
What about the idea to update '.fwd_mode_name' in 'noisy_fwd_begin()'? That way generic display code can stay as it is.
<...>
Quoted 33 lines
app/test-pmd/config.c +32
-0+static bool +pkt_burst_mac (struct fwd_stream *fs) +{ +struct rte_mbuf *pkts_burst[MAX_PKT_BURST ]; +uint16_t nb_rx; +uint16_t nb_tx; + + nb_rx =common_fwd_stream_receive (fs, pkts_burst, nb_pkt_per_burst); +if (likely (nb_rx !=0 )) +do_macfwd (pkts_burst, nb_rx, fs); + nb_tx =noisy_eth_tx_burst (fs, nb_rx, pkts_burst); + +return nb_rx >0 || nb_tx >0 ; +} +static bool +pkt_burst_macswap (struct fwd_stream *fs) +{ +struct rte_mbuf *pkts_burst[MAX_PKT_BURST ]; +uint16_t nb_rx; +uint16_t nb_tx; + + nb_rx =common_fwd_stream_receive (fs, pkts_burst, nb_pkt_per_burst); +if (likely (nb_rx !=0 )) +do_macswap (pkts_burst, nb_rx, &ports[fs->tx_port]); + nb_tx =noisy_eth_tx_burst (fs, nb_rx, pkts_burst); + +return nb_rx >0 || nb_tx >0 ; +} +static bool +pkt_burst_5tswap (struct fwd_stream *fs) +{ +struct rte_mbuf *pkts_burst[MAX_PKT_BURST ];
app/test-pmd/config.c
Quoted 10 lines
app/test-pmd/config.c +10
-0+uint16_t nb_rx; +uint16_t nb_tx; + + nb_rx =common_fwd_stream_receive (fs, pkts_burst, nb_pkt_per_burst); +if (likely (nb_rx !=0 )) +do_5tswap (pkts_burst, nb_rx, fs); + nb_tx =noisy_eth_tx_burst (fs, nb_rx, pkts_burst); + +return nb_rx >0 || nb_tx >0 ; +}
Empty lines are missing between functions.
Quoted 81 lines · Ferruh Yigit
Quoted 30 lines · Mike Pattrick
Previously the noisy neighbour vnf simulation would only operate in io mode, forwarding packets as is. However, this limited the usefulness of noisy neighbour simulation.
This feature has now been expanded to supporting mac, macswap, and 5tswap modes. To facilitate adding this support, some new header files were added.
Signed-off-by Mike Pattrick <[email protected]>---
v2: Reverted changes to random memory lookup
v3: Refactored entire patch
v4: Implemented recommended formatting changes
v5: Corrected copyright statement and formatting changes
v6: Reordered some variables, preserved noisy subtype for display--- app/test-pmd/5tswap.c | 118 +---------------------- app/test-pmd/5tswap.h | 130 ++++++++++++++++++++++++++ app/test-pmd/config.c | 18 +++- app/test-pmd/macfwd.c | 33 +------ app/test-pmd/macfwd.h | 45 +++++++++ app/test-pmd/noisy_vnf.c | 106 +++++++++++++++++---- app/test-pmd/parameters.c | 15 +++ app/test-pmd/testpmd.c | 14 +++ app/test-pmd/testpmd.h | 10 ++ doc/guides/testpmd_app_ug/run_app.rst | 9 ++ 10 files changed, 334 insertions(+), 164 deletions(-) create mode 100644 app/test-pmd/5tswap.h create mode 100644 app/test-pmd/macfwd.h<...>
Quoted 31 lines
app/test-pmd/config.c +13
-1@@ -4052,9 +4052,16 @@ rxtx_config_display(void) {portid_t pid;queueid_t qid; +char buf[32 ]; + +if (cur_fwd_eng == &noisy_vnf_engine) +snprintf (buf,sizeof (buf)," (%s)" , noisy_fwd_mode_desc[noisy_fwd_mode]); +else + buf[0 ] ='\0' ; -printf (" %s packet forwarding%s packets/burst=%d\n" , +printf (" %s%s packet forwarding%s packets/burst=%d\n" , cur_fwd_eng->fwd_mode_name, + buf, retry_enabled ==0 ?"" :" with retry" , nb_pkt_per_burst);@@ -4816,10 +4823,17 @@ pkt_fwd_config_display(struct fwd_config *cfg)struct fwd_stream *fs;lcoreid_t lc_id;streamid_t sm_id; +char buf[32 ]; + +if (cfg->fwd_eng == &noisy_vnf_engine) +snprintf (buf,sizeof (buf)," (%s)" , noisy_fwd_mode_desc[noisy_fwd_mode]); +else app/test-pmd/config.c pkt_fwd_config_display(struct fwd_config *cfg) · line 4839
Quoted 10 lines
app/test-pmd/config.c +3
-1+ buf[0 ] ='\0' ; - printf("%s packet forwarding%s - ports=%d - cores=%d - streams=%d - " + printf("%s%s packet forwarding%s - ports=%d - cores=%d - streams=%d - " "NUMA support %s, MP allocation mode: %s\n", cfg->fwd_eng->fwd_mode_name, + buf, retry_enabled == 0 ? "" : " with retry", cfg->nb_fwd_ports, cfg->nb_fwd_lcores, cfg->nb_fwd_streams, numa_support == 1 ? "enabled" : "disabled",This works but I wonder if we can keep the display functions generic (as much as possible), without forwarding enginee specific checks.
Quoted 2 lines
What about the idea to update '.fwd_mode_name' in '
noisy_fwd_begin()'? That way generic display code can stay as it is.
I worried that this would interfere with set_pkt_forwarding_mode() among other functions. The .fwd_mode_name seems to play double duty as view and model.
I was also thinking about adding another member to struct fwd_engine to display subtype / internal status. But I couldn't think of a compelling use case in the other modules. So I leaned towards this implementation.
Which do you prefer?
Quoted 50 lines
<...>
Quoted 33 lines
app/test-pmd/config.c +32
-0+static bool +pkt_burst_mac (struct fwd_stream *fs) +{ +struct rte_mbuf *pkts_burst[MAX_PKT_BURST ]; +uint16_t nb_rx; +uint16_t nb_tx; + + nb_rx =common_fwd_stream_receive (fs, pkts_burst, nb_pkt_per_burst); +if (likely (nb_rx !=0 )) +do_macfwd (pkts_burst, nb_rx, fs); + nb_tx =noisy_eth_tx_burst (fs, nb_rx, pkts_burst); + +return nb_rx >0 || nb_tx >0 ; +} +static bool +pkt_burst_macswap (struct fwd_stream *fs) +{ +struct rte_mbuf *pkts_burst[MAX_PKT_BURST ]; +uint16_t nb_rx; +uint16_t nb_tx; + + nb_rx =common_fwd_stream_receive (fs, pkts_burst, nb_pkt_per_burst); +if (likely (nb_rx !=0 )) +do_macswap (pkts_burst, nb_rx, &ports[fs->tx_port]); + nb_tx =noisy_eth_tx_burst (fs, nb_rx, pkts_burst); + +return nb_rx >0 || nb_tx >0 ; +} +static bool +pkt_burst_5tswap (struct fwd_stream *fs) +{ +struct rte_mbuf *pkts_burst[MAX_PKT_BURST ];app/test-pmd/config.c
Quoted 10 lines
app/test-pmd/config.c +10
-0+uint16_t nb_rx; +uint16_t nb_tx; + + nb_rx =common_fwd_stream_receive (fs, pkts_burst, nb_pkt_per_burst); +if (likely (nb_rx !=0 )) +do_5tswap (pkts_burst, nb_rx, fs); + nb_tx =noisy_eth_tx_burst (fs, nb_rx, pkts_burst); + +return nb_rx >0 || nb_tx >0 ; +}Empty lines are missing between functions.
Quoted 82 lines · Mike Pattrick
Quoted 81 lines · Ferruh Yigit
Quoted 30 lines · Mike Pattrick
Previously the noisy neighbour vnf simulation would only operate in io mode, forwarding packets as is. However, this limited the usefulness of noisy neighbour simulation.
This feature has now been expanded to supporting mac, macswap, and 5tswap modes. To facilitate adding this support, some new header files were added.
Signed-off-by Mike Pattrick <[email protected]>---
v2: Reverted changes to random memory lookup
v3: Refactored entire patch
v4: Implemented recommended formatting changes
v5: Corrected copyright statement and formatting changes
v6: Reordered some variables, preserved noisy subtype for display--- app/test-pmd/5tswap.c | 118 +---------------------- app/test-pmd/5tswap.h | 130 ++++++++++++++++++++++++++ app/test-pmd/config.c | 18 +++- app/test-pmd/macfwd.c | 33 +------ app/test-pmd/macfwd.h | 45 +++++++++ app/test-pmd/noisy_vnf.c | 106 +++++++++++++++++---- app/test-pmd/parameters.c | 15 +++ app/test-pmd/testpmd.c | 14 +++ app/test-pmd/testpmd.h | 10 ++ doc/guides/testpmd_app_ug/run_app.rst | 9 ++ 10 files changed, 334 insertions(+), 164 deletions(-) create mode 100644 app/test-pmd/5tswap.h create mode 100644 app/test-pmd/macfwd.h<...>
Quoted 31 lines
app/test-pmd/config.c +13
-1@@ -4052,9 +4052,16 @@ rxtx_config_display(void) {portid_t pid;queueid_t qid; +char buf[32 ]; + +if (cur_fwd_eng == &noisy_vnf_engine) +snprintf (buf,sizeof (buf)," (%s)" , noisy_fwd_mode_desc[noisy_fwd_mode]); +else + buf[0 ] ='\0' ; -printf (" %s packet forwarding%s packets/burst=%d\n" , +printf (" %s%s packet forwarding%s packets/burst=%d\n" , cur_fwd_eng->fwd_mode_name, + buf, retry_enabled ==0 ?"" :" with retry" , nb_pkt_per_burst);@@ -4816,10 +4823,17 @@ pkt_fwd_config_display(struct fwd_config *cfg)struct fwd_stream *fs;lcoreid_t lc_id;streamid_t sm_id; +char buf[32 ]; + +if (cfg->fwd_eng == &noisy_vnf_engine) +snprintf (buf,sizeof (buf)," (%s)" , noisy_fwd_mode_desc[noisy_fwd_mode]); +else app/test-pmd/config.c pkt_fwd_config_display(struct fwd_config *cfg) · line 4839
Quoted 10 lines
app/test-pmd/config.c +3
-1+ buf[0 ] ='\0' ; - printf("%s packet forwarding%s - ports=%d - cores=%d - streams=%d - " + printf("%s%s packet forwarding%s - ports=%d - cores=%d - streams=%d - " "NUMA support %s, MP allocation mode: %s\n", cfg->fwd_eng->fwd_mode_name, + buf, retry_enabled == 0 ? "" : " with retry", cfg->nb_fwd_ports, cfg->nb_fwd_lcores, cfg->nb_fwd_streams, numa_support == 1 ? "enabled" : "disabled",This works but I wonder if we can keep the display functions generic (as much as possible), without forwarding enginee specific checks.
Quoted 7 lines
Quoted 2 lines
What about the idea to update '.fwd_mode_name' in '
noisy_fwd_begin()'? That way generic display code can stay as it is.I worried that this would interfere with
set_pkt_forwarding_mode()among other functions. The .fwd_mode_name seems to play double duty as view and model.
You are right.
Quoted 7 lines
I was also thinking about adding another member to struct
fwd_engineto display subtype / internal status. But I couldn't think of a compelling use case in the other modules. So I leaned towards this implementation.Which do you prefer?
I think adding a new field is more proper, although I don't expect to have subtype for other forwarding modes, perhaps adding something like "internal status" may be useful later.
Quoted 51 lines
Quoted 50 lines
<...>
Quoted 33 lines
app/test-pmd/config.c +32
-0+static bool +pkt_burst_mac (struct fwd_stream *fs) +{ +struct rte_mbuf *pkts_burst[MAX_PKT_BURST ]; +uint16_t nb_rx; +uint16_t nb_tx; + + nb_rx =common_fwd_stream_receive (fs, pkts_burst, nb_pkt_per_burst); +if (likely (nb_rx !=0 )) +do_macfwd (pkts_burst, nb_rx, fs); + nb_tx =noisy_eth_tx_burst (fs, nb_rx, pkts_burst); + +return nb_rx >0 || nb_tx >0 ; +} +static bool +pkt_burst_macswap (struct fwd_stream *fs) +{ +struct rte_mbuf *pkts_burst[MAX_PKT_BURST ]; +uint16_t nb_rx; +uint16_t nb_tx; + + nb_rx =common_fwd_stream_receive (fs, pkts_burst, nb_pkt_per_burst); +if (likely (nb_rx !=0 )) +do_macswap (pkts_burst, nb_rx, &ports[fs->tx_port]); + nb_tx =noisy_eth_tx_burst (fs, nb_rx, pkts_burst); + +return nb_rx >0 || nb_tx >0 ; +} +static bool +pkt_burst_5tswap (struct fwd_stream *fs) +{ +struct rte_mbuf *pkts_burst[MAX_PKT_BURST ];app/test-pmd/config.c
Quoted 10 lines
app/test-pmd/config.c +10
-0+uint16_t nb_rx; +uint16_t nb_tx; + + nb_rx =common_fwd_stream_receive (fs, pkts_burst, nb_pkt_per_burst); +if (likely (nb_rx !=0 )) +do_5tswap (pkts_burst, nb_rx, fs); + nb_tx =noisy_eth_tx_burst (fs, nb_rx, pkts_burst); + +return nb_rx >0 || nb_tx >0 ; +}Empty lines are missing between functions.
PATCH v7 1/1 app/testpmd: expand noisy neighbour forward mode support
In reply to Mike PattrickPreviously the noisy neighbour vnf simulation would only operate in io mode, forwarding packets as is. However, this limited the usefulness of noisy neighbour simulation.
This feature has now been expanded to supporting mac, macswap, and 5tswap modes. To facilitate adding this support, some new header files were added.
---
v2: Reverted changes to random memory lookup
v3: Refactored entire patch
v4: Implemented recommended formatting changes
v5: Corrected copyright statement and formatting changes
v6: Reordered some variables, preserved noisy subtype for display
v7: Made fwd engine status generic across all modules
--- app/test-pmd/5tswap.c | 118 +---------------------- app/test-pmd/5tswap.h | 130 ++++++++++++++++++++++++++ app/test-pmd/config.c | 18 +++- app/test-pmd/macfwd.c | 33 +------ app/test-pmd/macfwd.h | 45 +++++++++ app/test-pmd/noisy_vnf.c | 113 ++++++++++++++++++---- app/test-pmd/parameters.c | 15 +++ app/test-pmd/testpmd.c | 14 +++ app/test-pmd/testpmd.h | 11 +++ doc/guides/testpmd_app_ug/run_app.rst | 9 ++ 10 files changed, 342 insertions(+), 164 deletions(-) create mode 100644 app/test-pmd/5tswap.h create mode 100644 app/test-pmd/macfwd.h
app/test-pmd/5tswap.c +3 -115
@@ -17,64 +17,8 @@#include <rte_ip.h> #include <rte_flow.h> -#include "macswap_common.h" #include "testpmd.h" - - -static inline void -swap_mac (struct rte_ether_hdr *eth_hdr) -{ -struct rte_ether_addr addr; - -/* Swap dest and src mac addresses. */ -rte_ether_addr_copy (ð_hdr->dst_addr, &addr); -rte_ether_addr_copy (ð_hdr->src_addr, ð_hdr->dst_addr); -rte_ether_addr_copy (&addr, ð_hdr->src_addr); -} - -static inline void -swap_ipv4 (struct rte_ipv4_hdr *ipv4_hdr) -{ -rte_be32_t addr; - -/* Swap dest and src ipv4 addresses. */ - addr = ipv4_hdr->src_addr; - ipv4_hdr->src_addr = ipv4_hdr->dst_addr; - ipv4_hdr->dst_addr = addr; -} - -static inline void -swap_ipv6 (struct rte_ipv6_hdr *ipv6_hdr) -{ -uint8_t addr[16 ]; - -/* Swap dest and src ipv6 addresses. */ -memcpy (&addr, &ipv6_hdr->src_addr,16 ); -memcpy (&ipv6_hdr->src_addr, &ipv6_hdr->dst_addr,16 ); -memcpy (&ipv6_hdr->dst_addr, &addr,16 ); -} - -static inline void -swap_tcp (struct rte_tcp_hdr *tcp_hdr) -{ -rte_be16_t port; - -/* Swap dest and src tcp port. */ - port = tcp_hdr->src_port; - tcp_hdr->src_port = tcp_hdr->dst_port; - tcp_hdr->dst_port = port; -} - -static inline void -swap_udp (struct rte_udp_hdr *udp_hdr) -{ -rte_be16_t port; - -/* Swap dest and src udp port */ - port = udp_hdr->src_port; - udp_hdr->src_port = udp_hdr->dst_port; - udp_hdr->dst_port = port; -} +#include "5tswap.h" /* * 5 tuple swap forwarding mode: Swap the source and the destination of layers
@@ -85,22 +29,7 @@ static bool pkt_burst_5tuple_swap(struct fwd_stream *fs) {struct rte_mbuf *pkts_burst[MAX_PKT_BURST ]; -struct rte_port *txp; -struct rte_mbuf *mb; -uint16_t next_proto; -uint64_t ol_flags; -uint16_t proto;uint16_t nb_rx; -int i; -union { -struct rte_ether_hdr *eth; -struct rte_vlan_hdr *vlan; -struct rte_ipv4_hdr *ipv4; -struct rte_ipv6_hdr *ipv6; -struct rte_tcp_hdr *tcp; -struct rte_udp_hdr *udp; -uint8_t *byte; - } h;/* * Receive a burst of packets and forward them.
@@ -109,49 +38,8 @@ pkt_burst_5tuple_swap(struct fwd_stream *fs)if (unlikely (nb_rx ==0 ))return false; - txp = &ports[fs->tx_port]; - ol_flags =ol_flags_init (txp->dev_conf.txmode.offloads); -vlan_qinq_set (pkts_burst, nb_rx, ol_flags, - txp->tx_vlan_id, txp->tx_vlan_id_outer); -for (i =0 ; i < nb_rx; i++) { -if (likely (i < nb_rx -1 )) -rte_prefetch0 (rte_pktmbuf_mtod (pkts_burst[i+1 ], - void *)); - mb = pkts_burst[i]; - h.eth = rte_pktmbuf_mtod(mb, struct rte_ether_hdr *); - proto = h.eth->ether_type; -swap_mac (h.eth); - mb->l2_len =sizeof (struct rte_ether_hdr ); - h.eth++; -while (proto ==RTE_BE16 (RTE_ETHER_TYPE_VLAN ) || - proto ==RTE_BE16 (RTE_ETHER_TYPE_QINQ )) { - proto = h.vlan->eth_proto; - h.vlan++; - mb->l2_len +=sizeof (struct rte_vlan_hdr ); - } -if (proto ==RTE_BE16 (RTE_ETHER_TYPE_IPV4 )) { -swap_ipv4 (h.ipv4); - next_proto = h.ipv4->next_proto_id; - mb->l3_len =rte_ipv4_hdr_len (h.ipv4); - h.byte += mb->l3_len; - }else if (proto ==RTE_BE16 (RTE_ETHER_TYPE_IPV6 )) { -swap_ipv6 (h.ipv6); - next_proto = h.ipv6->proto; - h.ipv6++; - mb->l3_len =sizeof (struct rte_ipv6_hdr ); - }else { -mbuf_field_set (mb, ol_flags); -continue ; - } -if (next_proto ==IPPROTO_UDP ) { -swap_udp (h.udp); - mb->l4_len =sizeof (struct rte_udp_hdr ); - }else if (next_proto ==IPPROTO_TCP ) { -swap_tcp (h.tcp); - mb->l4_len = (h.tcp->data_off &0xf0 ) >>2 ; - } -mbuf_field_set (mb, ol_flags); - } +do_5tswap (pkts_burst, nb_rx, fs); +common_fwd_stream_transmit (fs, pkts_burst, nb_rx);return true;
app/test-pmd/5tswap.h new file +130 -0
130 lines not on this page · raw message
app/test-pmd/config.c +16 -2
@@ -4052,9 +4052,16 @@ rxtx_config_display(void) {portid_t pid;queueid_t qid; +char buf[32 ]; + +if (cur_fwd_eng->status) +snprintf (buf,sizeof (buf)," (%s)" , cur_fwd_eng->status); +else + buf[0 ] ='\0' ; -printf (" %s packet forwarding%s packets/burst=%d\n" , +printf (" %s%s packet forwarding%s packets/burst=%d\n" , cur_fwd_eng->fwd_mode_name, + buf, retry_enabled ==0 ?"" :" with retry" , nb_pkt_per_burst);
@@ -4816,10 +4823,17 @@ pkt_fwd_config_display(struct fwd_config *cfg)struct fwd_stream *fs;lcoreid_t lc_id;streamid_t sm_id; +char buf[32 ]; + +if (cfg->fwd_eng->status) +snprintf (buf,sizeof (buf)," (%s)" , cfg->fwd_eng->status); +else + buf[0 ] ='\0' ; - printf("%s packet forwarding%s - ports=%d - cores=%d - streams=%d - " + printf("%s%s packet forwarding%s - ports=%d - cores=%d - streams=%d - " "NUMA support %s, MP allocation mode: %s\n", cfg->fwd_eng->fwd_mode_name, + buf, retry_enabled == 0 ? "" : " with retry", cfg->nb_fwd_ports, cfg->nb_fwd_lcores, cfg->nb_fwd_streams, numa_support == 1 ? "enabled" : "disabled",
app/test-pmd/macfwd.c +2 -31
@@ -35,6 +35,7 @@#include <rte_flow.h> #include "testpmd.h" +#include "macfwd.h" /* * Forwarding of packets in MAC mode.
@@ -45,13 +46,7 @@ static bool pkt_burst_mac_forward(struct fwd_stream *fs) {struct rte_mbuf *pkts_burst[MAX_PKT_BURST ]; -struct rte_port *txp; -struct rte_mbuf *mb; -struct rte_ether_hdr *eth_hdr;uint16_t nb_rx; -uint16_t i; -uint64_t ol_flags =0 ; -uint64_t tx_offloads;/* * Receive a burst of packets and forward them.
@@ -60,31 +55,7 @@ pkt_burst_mac_forward(struct fwd_stream *fs)if (unlikely (nb_rx ==0 ))return false; - txp = &ports[fs->tx_port]; - tx_offloads = txp->dev_conf.txmode.offloads; -if (tx_offloads &RTE_ETH_TX_OFFLOAD_VLAN_INSERT ) - ol_flags =RTE_MBUF_F_TX_VLAN ; -if (tx_offloads &RTE_ETH_TX_OFFLOAD_QINQ_INSERT ) - ol_flags |=RTE_MBUF_F_TX_QINQ ; -if (tx_offloads &RTE_ETH_TX_OFFLOAD_MACSEC_INSERT ) - ol_flags |=RTE_MBUF_F_TX_MACSEC ; -for (i =0 ; i < nb_rx; i++) { -if (likely (i < nb_rx -1 )) -rte_prefetch0 (rte_pktmbuf_mtod (pkts_burst[i +1 ], - void *)); - mb = pkts_burst[i]; - eth_hdr = rte_pktmbuf_mtod(mb, struct rte_ether_hdr *); -rte_ether_addr_copy (&peer_eth_addrs[fs->peer_addr], - ð_hdr->dst_addr); -rte_ether_addr_copy (&ports[fs->tx_port].eth_addr, - ð_hdr->src_addr); - mb->ol_flags &=RTE_MBUF_F_INDIRECT |RTE_MBUF_F_EXTERNAL ; - mb->ol_flags |= ol_flags; - mb->l2_len =sizeof (struct rte_ether_hdr ); - mb->l3_len =sizeof (struct rte_ipv4_hdr ); - mb->vlan_tci = txp->tx_vlan_id; - mb->vlan_tci_outer = txp->tx_vlan_id_outer; - } +do_macfwd (pkts_burst, nb_rx, fs);common_fwd_stream_transmit (fs, pkts_burst, nb_rx);
app/test-pmd/macfwd.h new file +45 -0
45 lines not on this page · raw message
app/test-pmd/noisy_vnf.c +97 -16
169 lines not on this page · raw message
app/test-pmd/parameters.c +15 -0
@@ -190,6 +190,7 @@ usage(char* progname)" anon: use regular DPDK memory to create and anonymous memory to populate mempool\n" " xmem: use anonymous memory to create and populate mempool\n" " xmemhuge: use anonymous hugepage memory to create and populate mempool\n"); +printf (" --noisy-forward-mode=<io|mac|macswap|5tswap>: set the sub-fwd mode, defaults to io\n" );printf (" --noisy-tx-sw-buffer-size=N: size of FIFO buffer\n" );printf (" --noisy-tx-sw-buffer-flushtime=N: flush FIFO after N ms\n" );printf (" --noisy-lkup-memory=N: allocate N MB of VNF memory\n" );
@@ -698,6 +699,7 @@ launch_args_parse(int argc, char** argv) { "mp-alloc", 1, 0, 0 }, { "tx-ip", 1, 0, 0 }, { "tx-udp", 1, 0, 0 }, + { "noisy-forward-mode", 1, 0, 0 }, { "noisy-tx-sw-buffer-size", 1, 0, 0 }, { "noisy-tx-sw-buffer-flushtime", 1, 0, 0 }, { "noisy-lkup-memory", 1, 0, 0 },
@@ -1444,6 +1446,19 @@ launch_args_parse(int argc, char** argv)rte_exit (EXIT_FAILURE ,"noisy-lkup-num-reads-writes must be >= 0\n" ); } +if (!strcmp (lgopts[opt_idx].name, +"noisy-forward-mode" )) { +int i; +for (i =0 ; i <NOISY_FWD_MODE_MAX ; i++) +if (!strcmp (optarg, noisy_fwd_mode_desc[i])) { + noisy_fwd_mode = i; +break ; + } +if (i ==NOISY_FWD_MODE_MAX ) +rte_exit (EXIT_FAILURE ,"noisy-forward-mode %s invalid," +" must be a valid noisy-forward-mode value\n" , + optarg); + }if (!strcmp (lgopts[opt_idx].name,"no-iova-contig" )) mempool_flags =RTE_MEMPOOL_F_NO_IOVA_CONTIG ;
app/test-pmd/testpmd.c +14 -0
@@ -330,6 +330,20 @@ int16_t tx_free_thresh = RTE_PMD_PARAM_UNSET;*/ int16_t tx_rs_thresh =RTE_PMD_PARAM_UNSET ; +/* +* Configurable sub-forwarding mode for the noisy_vnf forwarding mode. +*/ +enum noisy_fwd_mode noisy_fwd_mode; + +/* String version of enum noisy_fwd_mode */ +const char *const noisy_fwd_mode_desc[] = { + [NOISY_FWD_MODE_IO ] ="io" , + [NOISY_FWD_MODE_MAC ] ="mac" , + [NOISY_FWD_MODE_MACSWAP ] ="macswap" , + [NOISY_FWD_MODE_5TSWAP ] ="5tswap" , + [NOISY_FWD_MODE_MAX ] =NULL , +}; +/* * Configurable value of buffered packets before sending. */
app/test-pmd/testpmd.h +11 -0
@@ -116,6 +116,14 @@ enum { QUEUE_JOB_TYPE_ACTION_QUERY, }; +enum noisy_fwd_mode { +NOISY_FWD_MODE_IO , +NOISY_FWD_MODE_MAC , +NOISY_FWD_MODE_MACSWAP , +NOISY_FWD_MODE_5TSWAP , +NOISY_FWD_MODE_MAX , +}; +/** * The data structure associated with RX and TX packet burst statistics * that are recorded for each forwarding stream.
@@ -391,6 +399,7 @@ struct fwd_engine {port_fwd_end_t port_fwd_end;/**< NULL if nothing special to do. */ stream_init_t stream_init;/**< NULL if nothing special to do. */ packet_fwd_t packet_fwd;/**< Mandatory. */ +const char *status;/**< NULL if nothing to display. */ };void common_fwd_stream_init (struct fwd_stream *fs);
@@ -555,6 +564,8 @@ extern int8_t rx_drop_en;extern int16_t tx_free_thresh;extern int16_t tx_rs_thresh; +extern enum noisy_fwd_mode noisy_fwd_mode; +extern const char *const noisy_fwd_mode_desc[];extern uint16_t noisy_tx_sw_bufsz;extern uint16_t noisy_tx_sw_buf_flush_time;extern uint64_t noisy_lkup_mem_sz;
doc/guides/testpmd_app_ug/run_app.rst +9 -0
@@ -487,6 +487,15 @@ The command line options are: * xmemhuge: create and populate mempool using externally and anonymously allocated hugepage area +* ``--noisy-forward-mode=mode`` + + Set the noisy vnf forwarding mode where ``mode`` is one of the following:: + + io (the default) + mac + macswap + 5tswap + * ``--noisy-tx-sw-buffer-size`` Set the number of maximum elements of the FIFO queue to be created
Signature · 1 line
2.31.1
Quoted 10 lines · Mike Pattrick
Previously the noisy neighbour vnf simulation would only operate in io mode, forwarding packets as is. However, this limited the usefulness of noisy neighbour simulation.
This feature has now been expanded to supporting mac, macswap, and 5tswap modes. To facilitate adding this support, some new header files were added.
Signed-off-by Mike Pattrick <[email protected]>
Applied to dpdk-next-net/main, thanks.
Quoted 27 lines
app/test-pmd/config.c +13
-1@@ -4052,9 +4052,16 @@ rxtx_config_display(void) {portid_t pid;queueid_t qid; +char buf[32 ]; + +if (cur_fwd_eng->status) +snprintf (buf,sizeof (buf)," (%s)" , cur_fwd_eng->status); +else + buf[0 ] ='\0' ; -printf (" %s packet forwarding%s packets/burst=%d\n" , +printf (" %s%s packet forwarding%s packets/burst=%d\n" , cur_fwd_eng->fwd_mode_name, + buf, retry_enabled ==0 ?"" :" with retry" , nb_pkt_per_burst);@@ -4816,10 +4823,17 @@ pkt_fwd_config_display(struct fwd_config *cfg)struct fwd_stream *fs;lcoreid_t lc_id;streamid_t sm_id; +char buf[32 ]; + +if (cfg->fwd_eng->status) +snprintf (buf,sizeof (buf)," (%s)" , cfg->fwd_eng->status); +else
app/test-pmd/config.c pkt_fwd_config_display(struct fwd_config *cfg) · line 4839
Quoted 10 lines
app/test-pmd/config.c +3
-1+ buf[0 ] ='\0' ; - printf("%s packet forwarding%s - ports=%d - cores=%d - streams=%d - " + printf("%s%s packet forwarding%s - ports=%d - cores=%d - streams=%d - " "NUMA support %s, MP allocation mode: %s\n", cfg->fwd_eng->fwd_mode_name, + buf, retry_enabled == 0 ? "" : " with retry", cfg->nb_fwd_ports, cfg->nb_fwd_lcores, cfg->nb_fwd_streams, numa_support == 1 ? "enabled" : "disabled",
Removed interim 'buf' variable (and 'cfg->fwd_eng->status' specific check), and updated as following while merging:
```
- printf(" %s packet forwarding%s packets/burst=%d\n",
+ printf(" %s%s%s packet forwarding%s packets/burst=%d\n",
cur_fwd_eng->fwd_mode_name,
+ cur_fwd_eng->status ? "-" : "",
+ cur_fwd_eng->status ? cur_fwd_eng->status : "",
```