Revise Facebook Minerva BMC DTS
Subsystems (2)
cover Revise Facebook Minerva BMC DTS
Revise the Linux device tree entry related to Facebook platform Minerva specific devices connected to the Aspeed AST2600 BMC.
Changelog:
- v1:
- Modify the properties of spi to match the schema.
Yang Chen (17):
ARM: dts: aspeed: minerva: change the address of tmp75
ARM: dts: aspeed: minerva: change aliases for uart
ARM: dts: aspeed: minerva: add eeprom on i2c bus
ARM: dts: aspeed: minerva: change RTC reference
ARM: dts: aspeed: minerva: enable mdio3
ARM: dts: aspeed: minerva: remove unused bus and device
ARM: dts: aspeed: minerva: Define the LEDs node name
ARM: dts: aspeed: minerva: Add adc sensors for fan board
ARM: dts: aspeed: minerva: add linename of two pins
ARM: dts: aspeed: minerva: enable ehci0 for USB
ARM: dts: aspeed: minerva: add tmp75 sensor
ARM: dts: aspeed: minerva: add power monitor xdp710
ARM: dts: aspeed: minerva: revise sgpio line name
ARM: dts: aspeed: minerva: Switch the i2c bus number
ARM: dts: aspeed: minerva: remove unused power device
ARM: dts: aspeed: minerva: add ltc4287 device
ARM: dts: aspeed: minerva: Add spi-gpio
.../aspeed/aspeed-bmc-facebook-minerva.dts | 516 +++++++++++++----- 1 file changed, 373 insertions(+), 143 deletions(-)
Signature · 1 line
2.34.1
PATCH 1/17 ARM: dts: aspeed: minerva: change the address of tmp75
From: Yang Chen <[email protected]>
Revise the address of tmp75 on I2C bus 1 from 0x48 to 0x4f due to design change.
--- arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-minerva.dts | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-)
arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-minerva.dts +2 -2
@@ -145,9 +145,9 @@ temperature-sensor at 4b { reg = <0x4b>; }; - temperature-sensor at 48 { + temperature-sensor at 4f { compatible = "ti,tmp75"; - reg = <0x48>; + reg = <0x4f>; }; eeprom at 54 {
Signature · 1 line
2.34.1
PATCH 2/17 ARM: dts: aspeed: minerva: change aliases for uart
In reply to Yang ChenFrom: Yang Chen <[email protected]>
Change and add aliases name for uart interface.
--- arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-minerva.dts | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-)
arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-minerva.dts +2 -1
@@ -11,7 +11,8 @@ / { compatible = "facebook,minerva-cmc", "aspeed,ast2600"; aliases { - serial5 = &uart5; + serial4 = &uart5; + serial5 = &uart6; /* * PCA9548 (2-0077) provides 8 channels connecting to * 6 pcs of FCB (Fan Controller Board).
Signature · 1 line
2.34.1
PATCH 3/17 ARM: dts: aspeed: minerva: add eeprom on i2c bus
In reply to Yang ChenFrom: Yang Chen <[email protected]>
Add eeprom on the i2c-9 address 0x50 and i2c-15 address 0x56.
--- .../boot/dts/aspeed/aspeed-bmc-facebook-minerva.dts | 10 ++++++++++ 1 file changed, 10 insertions(+)
arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-minerva.dts +10 -0
@@ -303,6 +303,11 @@ &i2c8 { &i2c9 { status = "okay"; + + eeprom at 50 { + compatible = "atmel,24c64"; + reg = <0x50>; + }; }; &i2c10 {
@@ -339,6 +344,11 @@ eeprom at 50 { compatible = "atmel,24c128"; reg = <0x50>; }; + + eeprom at 56 { + compatible = "atmel,24c64"; + reg = <0x56>; + }; }; &adc0 {
Signature · 1 line
2.34.1
PATCH 4/17 ARM: dts: aspeed: minerva: change RTC reference
In reply to Yang ChenFrom: Yang Chen <[email protected]>
Change the RTC reference from on-chip to externel on i2c bus 9 and address is 0x51.
--- arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-minerva.dts | 9 +++++---- 1 file changed, 5 insertions(+), 4 deletions(-)
arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-minerva.dts +5 -4
@@ -95,10 +95,6 @@ flash at 1 { }; }; -&rtc { - status = "okay"; -}; - &sgpiom0 { status = "okay"; ngpios = <128>;
@@ -308,6 +304,11 @@ eeprom at 50 { compatible = "atmel,24c64"; reg = <0x50>; }; + + rtc at 51 { + compatible = "nxp,pcf8563"; + reg = <0x51>; + }; }; &i2c10 {
Signature · 1 line
2.34.1
PATCH 5/17 ARM: dts: aspeed: minerva: enable mdio3
In reply to Yang ChenFrom: Yang Chen <[email protected]>
Change usage of I2C bus 11 to mdio3.
--- arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-minerva.dts | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-)
arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-minerva.dts +4 -4
@@ -78,6 +78,10 @@ fixed-link { }; }; +&mdio3 { + status = "okay"; +}; + &fmc { status = "okay"; flash at 0 {
@@ -315,10 +319,6 @@ &i2c10 { status = "okay"; }; -&i2c11 { - status = "okay"; -}; - &i2c12 { status = "okay"; };
Signature · 1 line
2.34.1
PATCH 6/17 ARM: dts: aspeed: minerva: remove unused bus and device
In reply to Yang ChenFrom: Yang Chen <[email protected]>
Remove unused bus and device.
--- arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-minerva.dts | 4 ---- 1 file changed, 4 deletions(-)
arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-minerva.dts +0 -4
@@ -315,10 +315,6 @@ rtc at 51 { }; }; -&i2c10 { - status = "okay"; -}; - &i2c12 { status = "okay"; };
Signature · 1 line
2.34.1
PATCH 7/17 ARM: dts: aspeed: minerva: Define the LEDs node name
In reply to Yang ChenFrom: Yang Chen <[email protected]>
Define the LEDs node name.
--- .../aspeed/aspeed-bmc-facebook-minerva.dts | 28 +++++++++++++++++-- 1 file changed, 26 insertions(+), 2 deletions(-)
arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-minerva.dts +26 -2
@@ -44,11 +44,35 @@ iio-hwmon { leds { compatible = "gpio-leds"; - led-fan-fault { - label = "led-fan-fault"; + led-0 { + label = "bmc_heartbeat_amber"; + gpios = <&gpio0 ASPEED_GPIO(P, 7) GPIO_ACTIVE_LOW>; + linux,default-trigger = "heartbeat"; + }; + + led-1 { + label = "fp_id_amber"; + default-state = "off"; + gpios = <&gpio0 ASPEED_GPIO(B, 5) GPIO_ACTIVE_HIGH>; + }; + + led-2 { + label = "power_blue"; + default-state = "off"; + gpios = <&gpio0 ASPEED_GPIO(P, 4) GPIO_ACTIVE_HIGH>; + }; + + led-3 { + label = "fan_status_led"; gpios = <&leds_gpio 9 GPIO_ACTIVE_HIGH>; default-state = "off"; }; + + led-4 { + label = "fan_fault_led_n"; + gpios = <&leds_gpio 10 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; }; };
Signature · 1 line
2.34.1
PATCH 8/17 ARM: dts: aspeed: minerva: Add adc sensors for fan board
In reply to Yang ChenFrom: Yang Chen <[email protected]>
Add ina238 support to read the sensors in front of fans.
--- .../aspeed/aspeed-bmc-facebook-minerva.dts | 144 ++++++++++++++++++ 1 file changed, 144 insertions(+)
arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-minerva.dts +144 -0
@@ -207,6 +207,30 @@ pwm at 5e{ #address-cells = <1>; #size-cells = <0>; }; + + power-sensor at 40 { + compatible = "ti,ina238"; + reg = <0x40>; + shunt-resistor = <1000>; + }; + + power-sensor at 41 { + compatible = "ti,ina238"; + reg = <0x41>; + shunt-resistor = <1000>; + }; + + power-sensor at 44 { + compatible = "ti,ina238"; + reg = <0x44>; + shunt-resistor = <1000>; + }; + + power-sensor at 45 { + compatible = "ti,ina238"; + reg = <0x45>; + shunt-resistor = <1000>; + }; }; imux17: i2c at 1 {
@@ -225,6 +249,30 @@ pwm at 5e{ #address-cells = <1>; #size-cells = <0>; }; + + power-sensor at 40 { + compatible = "ti,ina238"; + reg = <0x40>; + shunt-resistor = <1000>; + }; + + power-sensor at 41 { + compatible = "ti,ina238"; + reg = <0x41>; + shunt-resistor = <1000>; + }; + + power-sensor at 44 { + compatible = "ti,ina238"; + reg = <0x44>; + shunt-resistor = <1000>; + }; + + power-sensor at 45 { + compatible = "ti,ina238"; + reg = <0x45>; + shunt-resistor = <1000>; + }; }; imux18: i2c at 2 {
@@ -243,6 +291,30 @@ pwm at 5e{ #address-cells = <1>; #size-cells = <0>; }; + + power-sensor at 40 { + compatible = "ti,ina238"; + reg = <0x40>; + shunt-resistor = <1000>; + }; + + power-sensor at 41 { + compatible = "ti,ina238"; + reg = <0x41>; + shunt-resistor = <1000>; + }; + + power-sensor at 44 { + compatible = "ti,ina238"; + reg = <0x44>; + shunt-resistor = <1000>; + }; + + power-sensor at 45 { + compatible = "ti,ina238"; + reg = <0x45>; + shunt-resistor = <1000>; + }; }; imux19: i2c at 3 {
@@ -261,6 +333,30 @@ pwm at 5e{ #address-cells = <1>; #size-cells = <0>; }; + + power-sensor at 40 { + compatible = "ti,ina238"; + reg = <0x40>; + shunt-resistor = <1000>; + }; + + power-sensor at 41 { + compatible = "ti,ina238"; + reg = <0x41>; + shunt-resistor = <1000>; + }; + + power-sensor at 44 { + compatible = "ti,ina238"; + reg = <0x44>; + shunt-resistor = <1000>; + }; + + power-sensor at 45 { + compatible = "ti,ina238"; + reg = <0x45>; + shunt-resistor = <1000>; + }; }; imux20: i2c at 4 {
@@ -279,6 +375,30 @@ pwm at 5e{ #address-cells = <1>; #size-cells = <0>; }; + + power-sensor at 40 { + compatible = "ti,ina238"; + reg = <0x40>; + shunt-resistor = <1000>; + }; + + power-sensor at 41 { + compatible = "ti,ina238"; + reg = <0x41>; + shunt-resistor = <1000>; + }; + + power-sensor at 44 { + compatible = "ti,ina238"; + reg = <0x44>; + shunt-resistor = <1000>; + }; + + power-sensor at 45 { + compatible = "ti,ina238"; + reg = <0x45>; + shunt-resistor = <1000>; + }; }; imux21: i2c at 5 {
@@ -297,6 +417,30 @@ pwm at 5e{ #address-cells = <1>; #size-cells = <0>; }; + + power-sensor at 40 { + compatible = "ti,ina238"; + reg = <0x40>; + shunt-resistor = <1000>; + }; + + power-sensor at 41 { + compatible = "ti,ina238"; + reg = <0x41>; + shunt-resistor = <1000>; + }; + + power-sensor at 44 { + compatible = "ti,ina238"; + reg = <0x44>; + shunt-resistor = <1000>; + }; + + power-sensor at 45 { + compatible = "ti,ina238"; + reg = <0x45>; + shunt-resistor = <1000>; + }; }; }; };
Signature · 1 line
2.34.1
PATCH 9/17 ARM: dts: aspeed: minerva: add linename of two pins
In reply to Yang ChenFrom: Yang Chen <[email protected]>
Add linename of two pins for power good/control.
--- arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-minerva.dts | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-)
arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-minerva.dts +2 -2
@@ -557,12 +557,12 @@ &gpio0 { /*N0-N7*/ "","","","","","","","", /*O0-O7*/ "","","","","","","","", /*P0-P7*/ "","","","","","","","", - /*Q0-Q7*/ "","","","","","","","", + /*Q0-Q7*/ "","","","","","power-chassis-control","","", /*R0-R7*/ "","","","","","","","", /*S0-S7*/ "","","","","","","","", /*T0-T7*/ "","","","","","","","", /*U0-U7*/ "","","","","","","","", - /*V0-V7*/ "","","","","BAT_DETECT","","","", + /*V0-V7*/ "","","","","BAT_DETECT","","power-chassis-good","", /*W0-W7*/ "","","","","","","","", /*X0-X7*/ "","","BLADE_UART_SEL3","","","","","", /*Y0-Y7*/ "","","","","","","","",
Signature · 1 line
2.34.1
PATCH 10/17 ARM: dts: aspeed: minerva: enable ehci0 for USB
In reply to Yang ChenFrom: Yang Chen <[email protected]>
Enable ehci0 for USB.
--- arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-minerva.dts | 4 ++++ 1 file changed, 4 insertions(+)
arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-minerva.dts +4 -0
@@ -531,6 +531,10 @@ &adc1 { pinctrl-0 = <&pinctrl_adc10_default>; }; +&ehci0 { + status = "okay"; +}; + &ehci1 { status = "okay"; };
Signature · 1 line
2.34.1
PATCH 11/17 ARM: dts: aspeed: minerva: add tmp75 sensor
In reply to Yang ChenFrom: Yang Chen <[email protected]>
Add tmp75 sensor on the i2c bus connect to each fan board.
--- .../aspeed/aspeed-bmc-facebook-minerva.dts | 28 +++++++++++++++++++ 1 file changed, 28 insertions(+)
arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-minerva.dts +28 -0
@@ -231,6 +231,11 @@ power-sensor at 45 { reg = <0x45>; shunt-resistor = <1000>; }; + + temperature-sensor at 4b { + compatible = "ti,tmp75"; + reg = <0x4b>; + }; }; imux17: i2c at 1 {
@@ -273,6 +278,11 @@ power-sensor at 45 { reg = <0x45>; shunt-resistor = <1000>; }; + + temperature-sensor at 4b { + compatible = "ti,tmp75"; + reg = <0x4b>; + }; }; imux18: i2c at 2 {
@@ -315,6 +325,11 @@ power-sensor at 45 { reg = <0x45>; shunt-resistor = <1000>; }; + + temperature-sensor at 4b { + compatible = "ti,tmp75"; + reg = <0x4b>; + }; }; imux19: i2c at 3 {
@@ -357,6 +372,11 @@ power-sensor at 45 { reg = <0x45>; shunt-resistor = <1000>; }; + + temperature-sensor at 4b { + compatible = "ti,tmp75"; + reg = <0x4b>; + }; }; imux20: i2c at 4 {
@@ -399,6 +419,10 @@ power-sensor at 45 { reg = <0x45>; shunt-resistor = <1000>; }; + temperature-sensor at 4b { + compatible = "ti,tmp75"; + reg = <0x4b>; + }; }; imux21: i2c at 5 {
@@ -441,6 +465,10 @@ power-sensor at 45 { reg = <0x45>; shunt-resistor = <1000>; }; + temperature-sensor at 4b { + compatible = "ti,tmp75"; + reg = <0x4b>; + }; }; }; };
Signature · 1 line
2.34.1
PATCH 12/17 ARM: dts: aspeed: minerva: add power monitor xdp710
In reply to Yang ChenFrom: Yang Chen <[email protected]>
Add HSC xdp710 on i2c bus0.
--- arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-minerva.dts | 5 +++++ 1 file changed, 5 insertions(+)
arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-minerva.dts +5 -0
@@ -154,6 +154,11 @@ power-monitor at 68 { reg = <0x68>; }; + power-monitor at 43 { + compatible = "infineon,xdp710"; + reg = <0x43>; + }; + leds_gpio: gpio at 19 { compatible = "nxp,pca9555"; reg = <0x19>;
Signature · 1 line
2.34.1
PATCH 13/17 ARM: dts: aspeed: minerva: revise sgpio line name
In reply to Yang ChenFrom: Yang Chen <[email protected]>
Revise the SGPIO naming to mapping the SGPIO from the CPLD.
--- .../aspeed/aspeed-bmc-facebook-minerva.dts | 236 +++++++++--------- 1 file changed, 118 insertions(+), 118 deletions(-)
arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-minerva.dts +118 -118
@@ -610,118 +610,118 @@ &sgpiom0 { gpio-line-names = /*"input pin","output pin"*/ /*A0 - A7*/ - "PRSNT_MTIA_BLADE0_N","PWREN_MTIA_BLADE0_EN", - "PRSNT_MTIA_BLADE1_N","PWREN_MTIA_BLADE1_EN", - "PRSNT_MTIA_BLADE2_N","PWREN_MTIA_BLADE2_EN", - "PRSNT_MTIA_BLADE3_N","PWREN_MTIA_BLADE3_EN", - "PRSNT_MTIA_BLADE4_N","PWREN_MTIA_BLADE4_EN", - "PRSNT_MTIA_BLADE5_N","PWREN_MTIA_BLADE5_EN", - "PRSNT_MTIA_BLADE6_N","PWREN_MTIA_BLADE6_EN", - "PRSNT_MTIA_BLADE7_N","PWREN_MTIA_BLADE7_EN", + "PRSNT_MTIA_BLADE0_N","PWREN_MTIA_BLADE0_EN_N", + "PRSNT_MTIA_BLADE1_N","PWREN_MTIA_BLADE1_EN_N", + "PRSNT_MTIA_BLADE2_N","PWREN_MTIA_BLADE2_EN_N", + "PRSNT_MTIA_BLADE3_N","PWREN_MTIA_BLADE3_EN_N", + "PRSNT_MTIA_BLADE4_N","PWREN_MTIA_BLADE4_EN_N", + "PRSNT_MTIA_BLADE5_N","PWREN_MTIA_BLADE5_EN_N", + "PRSNT_MTIA_BLADE6_N","PWREN_MTIA_BLADE6_EN_N", + "PRSNT_MTIA_BLADE7_N","PWREN_MTIA_BLADE7_EN_N", /*B0 - B7*/ - "PRSNT_MTIA_BLADE8_N","PWREN_MTIA_BLADE8_EN", - "PRSNT_MTIA_BLADE9_N","PWREN_MTIA_BLADE9_EN", - "PRSNT_MTIA_BLADE10_N","PWREN_MTIA_BLADE10_EN", - "PRSNT_MTIA_BLADE11_N","PWREN_MTIA_BLADE11_EN", - "PRSNT_MTIA_BLADE12_N","PWREN_MTIA_BLADE12_EN", - "PRSNT_MTIA_BLADE13_N","PWREN_MTIA_BLADE13_EN", - "PRSNT_MTIA_BLADE14_N","PWREN_MTIA_BLADE14_EN", - "PRSNT_MTIA_BLADE15_N","PWREN_MTIA_BLADE15_EN", + "PRSNT_MTIA_BLADE8_N","PWREN_MTIA_BLADE8_EN_N", + "PRSNT_MTIA_BLADE9_N","PWREN_MTIA_BLADE9_EN_N", + "PRSNT_MTIA_BLADE10_N","PWREN_MTIA_BLADE10_EN_N", + "PRSNT_MTIA_BLADE11_N","PWREN_MTIA_BLADE11_EN_N", + "PRSNT_MTIA_BLADE12_N","PWREN_MTIA_BLADE12_EN_N", + "PRSNT_MTIA_BLADE13_N","PWREN_MTIA_BLADE13_EN_N", + "PRSNT_MTIA_BLADE14_N","PWREN_MTIA_BLADE14_EN_N", + "PRSNT_MTIA_BLADE15_N","PWREN_MTIA_BLADE15_EN_N", /*C0 - C7*/ - "PRSNT_NW_BLADE0_N","PWREN_NW_BLADE0_EN", - "PRSNT_NW_BLADE1_N","PWREN_NW_BLADE1_EN", - "PRSNT_NW_BLADE2_N","PWREN_NW_BLADE2_EN", - "PRSNT_NW_BLADE3_N","PWREN_NW_BLADE3_EN", - "PRSNT_NW_BLADE4_N","PWREN_NW_BLADE4_EN", - "PRSNT_NW_BLADE5_N","PWREN_NW_BLADE5_EN", - "PRSNT_FCB_TOP_0_N","PWREN_MTIA_BLADE0_HSC_EN", - "PRSNT_FCB_TOP_1_N","PWREN_MTIA_BLADE1_HSC_EN", + "PRSNT_NW_BLADE0_N","PWREN_NW_BLADE0_EN_N", + "PRSNT_NW_BLADE1_N","PWREN_NW_BLADE1_EN_N", + "PRSNT_NW_BLADE2_N","PWREN_NW_BLADE2_EN_N", + "PRSNT_NW_BLADE3_N","PWREN_NW_BLADE3_EN_N", + "PRSNT_NW_BLADE4_N","PWREN_NW_BLADE4_EN_N", + "PRSNT_NW_BLADE5_N","PWREN_NW_BLADE5_EN_N", + "PRSNT_FCB_TOP_0_N","PWREN_MTIA_BLADE0_HSC_EN_N", + "PRSNT_FCB_TOP_1_N","PWREN_MTIA_BLADE1_HSC_EN_N", /*D0 - D7*/ - "PRSNT_FCB_MIDDLE_0_N","PWREN_MTIA_BLADE2_HSC_EN", - "PRSNT_FCB_MIDDLE_1_N","PWREN_MTIA_BLADE3_HSC_EN", - "PRSNT_FCB_BOTTOM_0_N","PWREN_MTIA_BLADE4_HSC_EN", - "PRSNT_FCB_BOTTOM_1_N","PWREN_MTIA_BLADE5_HSC_EN", - "PWRGD_MTIA_BLADE0_PWROK_L_BUF","PWREN_MTIA_BLADE6_HSC_EN", - "PWRGD_MTIA_BLADE1_PWROK_L_BUF","PWREN_MTIA_BLADE7_HSC_EN", - "PWRGD_MTIA_BLADE2_PWROK_L_BUF","PWREN_MTIA_BLADE8_HSC_EN", - "PWRGD_MTIA_BLADE3_PWROK_L_BUF","PWREN_MTIA_BLADE9_HSC_EN", + "PRSNT_FCB_MIDDLE_0_N","PWREN_MTIA_BLADE2_HSC_EN_N", + "PRSNT_FCB_MIDDLE_1_N","PWREN_MTIA_BLADE3_HSC_EN_N", + "PRSNT_FCB_BOTTOM_1_N","PWREN_MTIA_BLADE4_HSC_EN_N", + "PRSNT_FCB_BOTTOM_0_N","PWREN_MTIA_BLADE5_HSC_EN_N", + "PWRGD_MTIA_BLADE0_PWROK_N","PWREN_MTIA_BLADE6_HSC_EN_N", + "PWRGD_MTIA_BLADE1_PWROK_N","PWREN_MTIA_BLADE7_HSC_EN_N", + "PWRGD_MTIA_BLADE2_PWROK_N","PWREN_MTIA_BLADE8_HSC_EN_N", + "PWRGD_MTIA_BLADE3_PWROK_N","PWREN_MTIA_BLADE9_HSC_EN_N", /*E0 - E7*/ - "PWRGD_MTIA_BLADE4_PWROK_L_BUF","PWREN_MTIA_BLADE10_HSC_EN", - "PWRGD_MTIA_BLADE5_PWROK_L_BUF","PWREN_MTIA_BLADE11_HSC_EN", - "PWRGD_MTIA_BLADE6_PWROK_L_BUF","PWREN_MTIA_BLADE12_HSC_EN", - "PWRGD_MTIA_BLADE7_PWROK_L_BUF","PWREN_MTIA_BLADE13_HSC_EN", - "PWRGD_MTIA_BLADE8_PWROK_L_BUF","PWREN_MTIA_BLADE14_HSC_EN", - "PWRGD_MTIA_BLADE9_PWROK_L_BUF","PWREN_MTIA_BLADE15_HSC_EN", - "PWRGD_MTIA_BLADE10_PWROK_L_BUF","PWREN_NW_BLADE0_HSC_EN", - "PWRGD_MTIA_BLADE11_PWROK_L_BUF","PWREN_NW_BLADE1_HSC_EN", + "PWRGD_MTIA_BLADE4_PWROK_N","PWREN_MTIA_BLADE10_HSC_EN_N", + "PWRGD_MTIA_BLADE5_PWROK_N","PWREN_MTIA_BLADE11_HSC_EN_N", + "PWRGD_MTIA_BLADE6_PWROK_N","PWREN_MTIA_BLADE12_HSC_EN_N", + "PWRGD_MTIA_BLADE7_PWROK_N","PWREN_MTIA_BLADE13_HSC_EN_N", + "PWRGD_MTIA_BLADE8_PWROK_N","PWREN_MTIA_BLADE14_HSC_EN_N", + "PWRGD_MTIA_BLADE9_PWROK_N","PWREN_MTIA_BLADE15_HSC_EN_N", + "PWRGD_MTIA_BLADE10_PWROK_N","PWREN_NW_BLADE0_HSC_EN_N", + "PWRGD_MTIA_BLADE11_PWROK_N","PWREN_NW_BLADE1_HSC_EN_N", /*F0 - F7*/ - "PWRGD_MTIA_BLADE12_PWROK_L_BUF","PWREN_NW_BLADE2_HSC_EN", - "PWRGD_MTIA_BLADE13_PWROK_L_BUF","PWREN_NW_BLADE3_HSC_EN", - "PWRGD_MTIA_BLADE14_PWROK_L_BUF","PWREN_NW_BLADE4_HSC_EN", - "PWRGD_MTIA_BLADE15_PWROK_L_BUF","PWREN_NW_BLADE5_HSC_EN", - "PWRGD_NW_BLADE0_PWROK_L_BUF","PWREN_FCB_TOP_L_EN", - "PWRGD_NW_BLADE1_PWROK_L_BUF","PWREN_FCB_TOP_R_EN", - "PWRGD_NW_BLADE2_PWROK_L_BUF","PWREN_FCB_MIDDLE_L_EN", - "PWRGD_NW_BLADE3_PWROK_L_BUF","PWREN_FCB_MIDDLE_R_EN", + "PWRGD_MTIA_BLADE12_PWROK_N","PWREN_NW_BLADE2_HSC_EN_N", + "PWRGD_MTIA_BLADE13_PWROK_N","PWREN_NW_BLADE3_HSC_EN_N", + "PWRGD_MTIA_BLADE14_PWROK_N","PWREN_NW_BLADE4_HSC_EN_N", + "PWRGD_MTIA_BLADE15_PWROK_N","PWREN_NW_BLADE5_HSC_EN_N", + "PWRGD_NW_BLADE0_PWROK_N","PWREN_FCB_TOP_0_EN_N", + "PWRGD_NW_BLADE1_PWROK_N","PWREN_FCB_TOP_1_EN_N", + "PWRGD_NW_BLADE2_PWROK_N","PWREN_FCB_MIDDLE_0_EN_N", + "PWRGD_NW_BLADE3_PWROK_N","PWREN_FCB_MIDDLE_1_EN_N", /*G0 - G7*/ - "PWRGD_NW_BLADE4_PWROK_L_BUF","PWREN_FCB_BOTTOM_L_EN", - "PWRGD_NW_BLADE5_PWROK_L_BUF","PWREN_FCB_BOTTOM_R_EN", - "PWRGD_FCB_TOP_0_PWROK_L_BUF","FM_CMM_AC_CYCLE_N", - "PWRGD_FCB_TOP_1_PWROK_L_BUF","MGMT_SFP_TX_DIS", - "PWRGD_FCB_MIDDLE_0_PWROK_L_BUF","", - "PWRGD_FCB_MIDDLE_1_PWROK_L_BUF","RST_I2CRST_MTIA_BLADE0_1_N", - "PWRGD_FCB_BOTTOM_0_PWROK_L_BUF","RST_I2CRST_MTIA_BLADE2_3_N", - "PWRGD_FCB_BOTTOM_1_PWROK_L_BUF","RST_I2CRST_MTIA_BLADE4_5_N", + "PWRGD_NW_BLADE4_PWROK_N","PWREN_FCB_BOTTOM_1_EN_N", + "PWRGD_NW_BLADE5_PWROK_N","PWREN_FCB_BOTTOM_0_EN_N", + "PWRGD_FCB_TOP_0_PWROK_N","FM_CMM_AC_CYCLE_N", + "PWRGD_FCB_TOP_1_PWROK_N","MGMT_SFP_TX_DIS", + "PWRGD_FCB_MIDDLE_0_PWROK_N","FM_MDIO_SW_SEL", + "PWRGD_FCB_MIDDLE_1_PWROK_N","FM_P24V_SMPWR_EN", + "PWRGD_FCB_BOTTOM_1_PWROK_N","", + "PWRGD_FCB_BOTTOM_0_PWROK_N","", /*H0 - H7*/ - "LEAK_DETECT_MTIA_BLADE0_N_BUF","RST_I2CRST_MTIA_BLADE6_7_N", - "LEAK_DETECT_MTIA_BLADE1_N_BUF","RST_I2CRST_MTIA_BLADE8_9_N", - "LEAK_DETECT_MTIA_BLADE2_N_BUF","RST_I2CRST_MTIA_BLADE10_11_N", - "LEAK_DETECT_MTIA_BLADE3_N_BUF","RST_I2CRST_MTIA_BLADE12_13_N", - "LEAK_DETECT_MTIA_BLADE4_N_BUF","RST_I2CRST_MTIA_BLADE14_15_N", - "LEAK_DETECT_MTIA_BLADE5_N_BUF","RST_I2CRST_NW_BLADE0_1_2_N", - "LEAK_DETECT_MTIA_BLADE6_N_BUF","RST_I2CRST_NW_BLADE3_4_5_N", - "LEAK_DETECT_MTIA_BLADE7_N_BUF","RST_I2CRST_FCB_N", + "LEAK_DETECT_MTIA_BLADE0_N","", + "LEAK_DETECT_MTIA_BLADE1_N","", + "LEAK_DETECT_MTIA_BLADE2_N","", + "LEAK_DETECT_MTIA_BLADE3_N","", + "LEAK_DETECT_MTIA_BLADE4_N","", + "LEAK_DETECT_MTIA_BLADE5_N","", + "LEAK_DETECT_MTIA_BLADE6_N","", + "LEAK_DETECT_MTIA_BLADE7_N","", /*I0 - I7*/ - "LEAK_DETECT_MTIA_BLADE8_N_BUF","RST_I2CRST_FCB_B_L_N", - "LEAK_DETECT_MTIA_BLADE9_N_BUF","RST_I2CRST_FCB_B_R_N", - "LEAK_DETECT_MTIA_BLADE10_N_BUF","RST_I2CRST_FCB_M_L_N", - "LEAK_DETECT_MTIA_BLADE11_N_BUF","RST_I2CRST_FCB_M_R_N", - "LEAK_DETECT_MTIA_BLADE12_N_BUF","RST_I2CRST_FCB_T_L_N", - "LEAK_DETECT_MTIA_BLADE13_N_BUF","RST_I2CRST_FCB_T_R_N", - "LEAK_DETECT_MTIA_BLADE14_N_BUF","BMC_READY", - "LEAK_DETECT_MTIA_BLADE15_N_BUF","wFM_88E6393X_BIN_UPDATE_EN_N", + "LEAK_DETECT_MTIA_BLADE8_N","RST_I2CRST_FCB_BOTTOM_1_N", + "LEAK_DETECT_MTIA_BLADE9_N","RST_I2CRST_FCB_BOTTOM_0_N", + "LEAK_DETECT_MTIA_BLADE10_N","RST_I2CRST_FCB_MIDDLE_0_N", + "LEAK_DETECT_MTIA_BLADE11_N","RST_I2CRST_FCB_MIDDLE_1_N", + "LEAK_DETECT_MTIA_BLADE12_N","RST_I2CRST_FCB_TOP_0_N", + "LEAK_DETECT_MTIA_BLADE13_N","RST_I2CRST_FCB_TOP_1_N", + "LEAK_DETECT_MTIA_BLADE14_N","BMC_READY", + "LEAK_DETECT_MTIA_BLADE15_N","FM_88E6393X_BIN_UPDATE_EN_N", /*J0 - J7*/ - "LEAK_DETECT_NW_BLADE0_N_BUF","WATER_VALVE_CLOSED_N", - "LEAK_DETECT_NW_BLADE1_N_BUF","", - "LEAK_DETECT_NW_BLADE2_N_BUF","", - "LEAK_DETECT_NW_BLADE3_N_BUF","", - "LEAK_DETECT_NW_BLADE4_N_BUF","", - "LEAK_DETECT_NW_BLADE5_N_BUF","", - "MTIA_BLADE0_STATUS_LED","", - "MTIA_BLADE1_STATUS_LED","", + "LEAK_DETECT_NW_BLADE0_N","WATER_VALVE_CLOSED_N", + "LEAK_DETECT_NW_BLADE1_N","", + "LEAK_DETECT_NW_BLADE2_N","", + "LEAK_DETECT_NW_BLADE3_N","", + "LEAK_DETECT_NW_BLADE4_N","", + "LEAK_DETECT_NW_BLADE5_N","", + "PWRGD_MTIA_BLADE0_HSC_PWROK_N","", + "PWRGD_MTIA_BLADE1_HSC_PWROK_N","", /*K0 - K7*/ - "MTIA_BLADE2_STATUS_LED","", - "MTIA_BLADE3_STATUS_LED","", - "MTIA_BLADE4_STATUS_LED","", - "MTIA_BLADE5_STATUS_LED","", - "MTIA_BLADE6_STATUS_LED","", - "MTIA_BLADE7_STATUS_LED","", - "MTIA_BLADE8_STATUS_LED","", - "MTIA_BLADE9_STATUS_LED","", + "PWRGD_MTIA_BLADE2_HSC_PWROK_N","", + "PWRGD_MTIA_BLADE3_HSC_PWROK_N","", + "PWRGD_MTIA_BLADE4_HSC_PWROK_N","", + "PWRGD_MTIA_BLADE5_HSC_PWROK_N","", + "PWRGD_MTIA_BLADE6_HSC_PWROK_N","", + "PWRGD_MTIA_BLADE7_HSC_PWROK_N","", + "PWRGD_MTIA_BLADE8_HSC_PWROK_N","", + "PWRGD_MTIA_BLADE9_HSC_PWROK_N","", /*L0 - L7*/ - "MTIA_BLADE10_STATUS_LED","", - "MTIA_BLADE11_STATUS_LED","", - "MTIA_BLADE12_STATUS_LED","", - "MTIA_BLADE13_STATUS_LED","", - "MTIA_BLADE14_STATUS_LED","", - "MTIA_BLADE15_STATUS_LED","", - "NW_BLADE0_STATUS_LED","", - "NW_BLADE1_STATUS_LED","", + "PWRGD_MTIA_BLADE10_HSC_PWROK_N","", + "PWRGD_MTIA_BLADE11_HSC_PWROK_N","", + "PWRGD_MTIA_BLADE12_HSC_PWROK_N","", + "PWRGD_MTIA_BLADE13_HSC_PWROK_N","", + "PWRGD_MTIA_BLADE14_HSC_PWROK_N","", + "PWRGD_MTIA_BLADE15_HSC_PWROK_N","", + "PWRGD_NW_BLADE0_HSC_PWROK_N","", + "PWRGD_NW_BLADE1_HSC_PWROK_N","", /*M0 - M7*/ - "NW_BLADE2_STATUS_LED","", - "NW_BLADE3_STATUS_LED","", - "NW_BLADE4_STATUS_LED","", - "NW_BLADE5_STATUS_LED","", + "PWRGD_NW_BLADE2_HSC_PWROK_N","", + "PWRGD_NW_BLADE3_HSC_PWROK_N","", + "PWRGD_NW_BLADE4_HSC_PWROK_N","", + "PWRGD_NW_BLADE5_HSC_PWROK_N","", "RPU_READY","", "IT_GEAR_RPU_LINK_N","", "IT_GEAR_LEAK","",
@@ -729,28 +729,28 @@ &sgpiom0 { /*N0 - N7*/ "VALVE_STS0","", "VALVE_STS1","", - "VALVE_STS2","", - "VALVE_STS3","", - "CR_TOGGLE_BOOT_BUF_N","", - "CMM_LC_RDY_LED_N","", - "CMM_LC_UNRDY_LED_N","", + "PCA9555_IRQ0_N","", + "PCA9555_IRQ1_N","", + "CR_TOGGLE_BOOT_N","", + "IRQ_FCB_TOP0_N","", + "IRQ_FCB_TOP1_N","", "CMM_CABLE_CARTRIDGE_PRSNT_BOT_N","", /*O0 - O7*/ "CMM_CABLE_CARTRIDGE_PRSNT_TOP_N","", "BOT_BCB_CABLE_PRSNT_N","", "TOP_BCB_CABLE_PRSNT_N","", - "CHASSIS0_LEAK_Q_N","", - "CHASSIS1_LEAK_Q_N","", - "LEAK0_DETECT","", - "LEAK1_DETECT","", - "MGMT_SFP_PRSNT_N","", + "IRQ_FCB_MID0_N","", + "IRQ_FCB_MID1_N","", + "CHASSIS_LEAK0_DETECT_N","", + "CHASSIS_LEAK1_DETECT_N","", + "VALVE_RMON_A_1","", /*P0 - P7*/ - "MGMT_SFP_TX_FAULT","", - "MGMT_SFP_RX_LOS","", - "","", - "","", - "","", - "","", - "","", - "",""; + "VALVE_RMON_A_2","", + "VALVE_RMON_B_1","", + "VALVE_RMON_B_2","", + "RPU_READY_SPARE","", + "IT_GEAR_LEAK_SPARE","", + "IT_GEAR_RPU_LINK_SPARE_N","", + "IRQ_FCB_BOT0_N","", + "IRQ_FCB_BOT0_N",""; };
Signature · 1 line
2.34.1
PATCH 14/17 ARM: dts: aspeed: minerva: Switch the i2c bus number
In reply to Yang ChenFrom: Yang Chen <[email protected]>
Switch the i2c bus number to map the i2c tag according to the hardware design.
--- arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-minerva.dts | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-)
arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-minerva.dts +2 -2
@@ -384,7 +384,7 @@ temperature-sensor at 4b { }; }; - imux20: i2c at 4 { + imux20: i2c at 5 { #address-cells = <1>; #size-cells = <0>; reg = <4>;
@@ -430,7 +430,7 @@ temperature-sensor at 4b { }; }; - imux21: i2c at 5 { + imux21: i2c at 4 { #address-cells = <1>; #size-cells = <0>; reg = <5>;
Signature · 1 line
2.34.1
PATCH 15/17 ARM: dts: aspeed: minerva: remove unused power device
In reply to Yang ChenRemove unused power device.
--- .../boot/dts/aspeed/aspeed-bmc-facebook-minerva.dts | 10 ---------- 1 file changed, 10 deletions(-)
arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-minerva.dts +0 -10
@@ -144,16 +144,6 @@ power-monitor at 41 { shunt-resistor = <1000>; }; - power-monitor at 67 { - compatible = "adi,ltc2945"; - reg = <0x67>; - }; - - power-monitor at 68 { - compatible = "adi,ltc2945"; - reg = <0x68>; - }; - power-monitor at 43 { compatible = "infineon,xdp710"; reg = <0x43>;
Signature · 1 line
2.34.1
PATCH 16/17 ARM: dts: aspeed: minerva: add ltc4287 device
In reply to Yang ChenEnable LTC4287 device on i2c-0.
--- arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-minerva.dts | 6 ++++++ 1 file changed, 6 insertions(+)
arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-minerva.dts +6 -0
@@ -144,6 +144,12 @@ power-monitor at 41 { shunt-resistor = <1000>; }; + power-monitor at 44 { + compatible = "lltc,ltc4287"; + reg = <0x44>; + shunt-resistor-micro-ohms = <2000>; + }; + power-monitor at 43 { compatible = "infineon,xdp710"; reg = <0x43>;
Signature · 1 line
2.34.1
PATCH 17/17 ARM: dts: aspeed: minerva: Add spi-gpio
In reply to Yang ChenFrom: Yang Chen <[email protected]>
Add spi-gpio for TPM device.
--- .../aspeed/aspeed-bmc-facebook-minerva.dts | 21 +++++++++++++++++++ 1 file changed, 21 insertions(+)
arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-minerva.dts +21 -0
@@ -23,6 +23,8 @@ aliases { i2c19 = &imux19; i2c20 = &imux20; i2c21 = &imux21; + + spi1 = &spi_gpio; }; chosen {
@@ -74,6 +76,25 @@ led-4 { default-state = "off"; }; }; + + spi_gpio: spi { + status = "okay"; + compatible = "spi-gpio"; + #address-cells = <1>; + #size-cells = <0>; + + sck-gpios = <&gpio0 ASPEED_GPIO(Z, 3) GPIO_ACTIVE_HIGH>; + mosi-gpios = <&gpio0 ASPEED_GPIO(Z, 4) GPIO_ACTIVE_HIGH>; + miso-gpios = <&gpio0 ASPEED_GPIO(Z, 5) GPIO_ACTIVE_HIGH>; + num-chipselects = <1>; + cs-gpios = <&gpio0 ASPEED_GPIO(Z, 0) GPIO_ACTIVE_LOW>; + + tpm at 0 { + compatible = "infineon,slb9670", "tcg,tpm_tis-spi"; + spi-max-frequency = <33000000>; + reg = <0>; + }; + }; }; &uart6 {
Signature · 1 line
2.34.1
Rob Herring
maintainerQuoted 6 lines · On Wed, Jun 26, 2024 at 7:05?AM Yang Chen <[email protected]> wrote:
Revise the Linux device tree entry related to Facebook platform Minerva specific devices connected to the Aspeed AST2600 BMC.
Changelog:
- v1:
You already sent v1. This is v2.
Quoted 28 lines
- Modify the properties of spi to match the schema.
Yang Chen (17):
ARM: dts: aspeed: minerva: change the address of tmp75
ARM: dts: aspeed: minerva: change aliases for uart
ARM: dts: aspeed: minerva: add eeprom on i2c bus
ARM: dts: aspeed: minerva: change RTC reference
ARM: dts: aspeed: minerva: enable mdio3
ARM: dts: aspeed: minerva: remove unused bus and device
ARM: dts: aspeed: minerva: Define the LEDs node name
ARM: dts: aspeed: minerva: Add adc sensors for fan board
ARM: dts: aspeed: minerva: add linename of two pins
ARM: dts: aspeed: minerva: enable ehci0 for USB
ARM: dts: aspeed: minerva: add tmp75 sensor
ARM: dts: aspeed: minerva: add power monitor xdp710
ARM: dts: aspeed: minerva: revise sgpio line name
ARM: dts: aspeed: minerva: Switch the i2c bus number
ARM: dts: aspeed: minerva: remove unused power device
ARM: dts: aspeed: minerva: add ltc4287 device
ARM: dts: aspeed: minerva: Add spi-gpio.../aspeed/aspeed-bmc-facebook-minerva.dts | 516 +++++++++++++----- 1 file changed, 373 insertions(+), 143 deletions(-)--
2.34.1
Quoted 10 lines · On Wed, Jun 26, 2024 at 9:38?PM Rob Herring <[email protected]> wrote:
Quoted 6 lines · On Wed, Jun 26, 2024 at 7:05?AM Yang Chen <[email protected]> wrote:
Revise the Linux device tree entry related to Facebook platform Minerva specific devices connected to the Aspeed AST2600 BMC.
Changelog:
- v1:You already sent v1. This is v2.
Hi Rob,
I appreciate your reminder. Should I send another patch series and use v3?
Thanks,
Yang Chen
Quoted 29 lines
Quoted 29 lines
- Modify the properties of spi to match the schema.
Yang Chen (17):
ARM: dts: aspeed: minerva: change the address of tmp75
ARM: dts: aspeed: minerva: change aliases for uart
ARM: dts: aspeed: minerva: add eeprom on i2c bus
ARM: dts: aspeed: minerva: change RTC reference
ARM: dts: aspeed: minerva: enable mdio3
ARM: dts: aspeed: minerva: remove unused bus and device
ARM: dts: aspeed: minerva: Define the LEDs node name
ARM: dts: aspeed: minerva: Add adc sensors for fan board
ARM: dts: aspeed: minerva: add linename of two pins
ARM: dts: aspeed: minerva: enable ehci0 for USB
ARM: dts: aspeed: minerva: add tmp75 sensor
ARM: dts: aspeed: minerva: add power monitor xdp710
ARM: dts: aspeed: minerva: revise sgpio line name
ARM: dts: aspeed: minerva: Switch the i2c bus number
ARM: dts: aspeed: minerva: remove unused power device
ARM: dts: aspeed: minerva: add ltc4287 device
ARM: dts: aspeed: minerva: Add spi-gpio.../aspeed/aspeed-bmc-facebook-minerva.dts | 516 +++++++++++++----- 1 file changed, 373 insertions(+), 143 deletions(-)--
2.34.1
Rob Herring
maintainerQuoted 8 lines · On Wed, Jun 26, 2024 at 8:02?AM Yang Chen <[email protected]> wrote:
Quoted 6 lines · On Wed, Jun 26, 2024 at 9:38?PM Rob Herring <[email protected]> wrote:
Quoted 4 lines · On Wed, Jun 26, 2024 at 7:05?AM Yang Chen <[email protected]> wrote:
Revise the Linux device tree entry related to Facebook platform Minerva specific devices connected to the Aspeed AST2600 BMC.
Quoted 7 lines
Quoted 4 lines
Quoted 2 lines
Changelog:
- v1:You already sent v1. This is v2.
Hi Rob,
I appreciate your reminder. Should I send another patch series and use v3?
Not until you have changes on this version.
Rob
Andrew Jeffery
maintainerHello Yang Chen,
Quoted 6 lines · Yang Chen
Revise the Linux device tree entry related to Facebook platform Minerva specific devices connected to the Aspeed AST2600 BMC.
Changelog:
- v1:
- Modify the properties of spi to match the schema.
I've put this series into a tree for Joel to pick up.
Thanks,
Andrew