Skip to contentSkip to conversation

net: stmmac: enable the MAC on link up at 10G on 10GBASE-R

PATCH In review vadik likholetov 3 participants 5 messages Jul 10 – Jul 12

Subsystems (5)
lore
Share & tools
lore
#0 lore raw

PATCH 1/1 net: stmmac: enable the MAC on link up at 10G on 10GBASE-R

stmmac_mac_link_down() clears the MAC's transmit and receive enable bits. stmmac_mac_link_up() is expected to set them again through stmmac_mac_set(..., true), but it first switches on the negotiated speed and returns early for a speed it does not recognise.

The generic branch of that switch -- taken for every interface that is neither USXGMII nor XLGMII, which includes PHY_INTERFACE_MODE_10GBASER -- handles only SPEED_2500, SPEED_1000, SPEED_100 and SPEED_10.

MGBE on Tegra234 runs 10GBASE-R into an Aquantia AQR113C. That PHY does rate matching, so phylink_link_up() replaces the media speed with the MAC-side interface speed before calling into the MAC:

	case RATE_MATCH_PAUSE:
		speed = phylink_interface_max_speed(link_state.interface);
		duplex = DUPLEX_FULL;

The driver is therefore called as

	stmmac_mac_link_up(interface=10GBASER, speed=10000, duplex=1)

which falls through to "default: return;". The MAC is never re-enabled, and the interface stops passing traffic after the first link flap.

The failure is easy to misread. The link still comes up, because the PHY is polled over MDIO and needs no MAC, so the interface reports carrier 1 at the media speed. The DMA is untouched, so its start bits stay set and descriptors are still consumed. Only the MAC itself is gated off: the receiver counts nothing (mmc_rx_framecount_gb stops advancing, RE is 0) and nothing reaches the wire (TE is 0). The interface survives boot only because stmmac_hw_setup(), called from ndo_open, enables the MAC unconditionally -- so the problem appears only once the cable has been unplugged and plugged back in, and "ip link set dev <ethX> down && ip link set dev <ethX> up" appears to fix it.

Handle SPEED_10000 in the generic branch, as the USXGMII and XLGMII branches already do. For dwxgmac2, link.xgmii.speed10000 is XGMAC_CONFIG_SS_10000, which is 0 and is the correct speed selection for a 10GBASE-R MAC: ctrl then equals old_ctrl, the register write is skipped, and execution reaches stmmac_mac_set(..., true).

Fixes d8ca113724e7 ("net: stmmac: tegra: Add MGBE support")

---
Verified on an AGX Orin devkit (Tegra234 MGBE0 + AQR113C), before and after, on the same board and cable. MAC registers read with ethtool -d, after a physical unplug and replug:

stock MAC_TX_CONFIG 0x00010000 (TE=0)

		MAC_RX_CONFIG 0x3ff022c0 (RE=0)
		rx_packets frozen, DHCP lease lost

patched MAC_TX_CONFIG 0x00010001 (TE=1)

		MAC_RX_CONFIG 0x3ff022c1 (RE=1)
		rx_packets keeps climbing, DHCP lease retained

A kprobe trace of the stock kernel across a link flap shows the mechanism directly -- dwxgmac2_set_mac(enable=1) never follows the link-up:

linkdown: (stmmac_mac_link_down+0x0/0xc8) iface=27
setmac: (dwxgmac2_set_mac+0x0/0x80) enable=0
linkup: (stmmac_mac_link_up+0x0/0x350) iface=27 speed=10000 duplex=1

(iface 27 is PHY_INTERFACE_MODE_10GBASER.)

Note on the Fixes tag: the missing SPEED_10000 case in the generic branch predates the commit cited above. I picked d8ca113724e7 because MGBE is the first in-tree user to reach it -- it needs a 10GBASE-R interface driven by a rate-matching PHY, so that phylink hands the MAC a 10G speed on a link that negotiated slower. Happy to re-target the tag if you would rather it point at the stmmac commit that introduced the switch.

Testing was done with MGBE0 handed to a VM via vfio-platform, so the driver ran in a guest; the MAC register evidence above is read from the device itself and the code path is not virtualisation-specific. I do not have a bare-metal AGX Orin running mainline dwmac-tegra to confirm on, but nothing in the analysis depends on the passthrough.

 drivers/net/ethernet/stmicro/stmmac/stmmac_main.c | 3 +++
 1 file changed, 3 insertions(+)
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c +3 -0
@@ -1125,6 +1125,9 @@ static void stmmac_mac_link_up(struct phylink_config *config,
 		}
 	} else {
 		switch (speed) {
+		case SPEED_10000:
+			ctrl |= priv->hw->link.xgmii.speed10000;
+			break;
 		case SPEED_2500:
 			ctrl |= priv->hw->link.speed2500;
 			break;

--
2.51.0

#1 lore raw

Hi,

Quoted 35 lines · vadik likholetov

stmmac_mac_link_down() clears the MAC's transmit and receive enable bits. stmmac_mac_link_up() is expected to set them again through stmmac_mac_set(..., true), but it first switches on the negotiated speed and returns early for a speed it does not recognise.

The generic branch of that switch -- taken for every interface that is neither USXGMII nor XLGMII, which includes PHY_INTERFACE_MODE_10GBASER -- handles only SPEED_2500, SPEED_1000, SPEED_100 and SPEED_10.

MGBE on Tegra234 runs 10GBASE-R into an Aquantia AQR113C. That PHY does rate matching, so phylink_link_up() replaces the media speed with the MAC-side interface speed before calling into the MAC:

	case RATE_MATCH_PAUSE:
		speed = phylink_interface_max_speed(link_state.interface);
		duplex = DUPLEX_FULL;

The driver is therefore called as

	stmmac_mac_link_up(interface=10GBASER, speed=10000, duplex=1)

which falls through to "default: return;". The MAC is never re-enabled, and the interface stops passing traffic after the first link flap.

The failure is easy to misread. The link still comes up, because the PHY is polled over MDIO and needs no MAC, so the interface reports carrier 1 at the media speed. The DMA is untouched, so its start bits stay set and descriptors are still consumed. Only the MAC itself is gated off: the receiver counts nothing (mmc_rx_framecount_gb stops advancing, RE is 0) and nothing reaches the wire (TE is 0). The interface survives boot only because stmmac_hw_setup(), called from ndo_open, enables the MAC unconditionally -- so the problem appears only once the cable has been unplugged and plugged back in, and "ip link set dev <ethX> down && ip link set dev <ethX> up" appears to fix it.

Quoted 8 lines

Handle SPEED_10000 in the generic branch, as the USXGMII and XLGMII branches already do. For dwxgmac2, link.xgmii.speed10000 is XGMAC_CONFIG_SS_10000, which is 0 and is the correct speed selection for a 10GBASE-R MAC: ctrl then equals old_ctrl, the register write is skipped, and execution reaches stmmac_mac_set(..., true).

Fixes d8ca113724e7 ("net: stmmac: tegra: Add MGBE support")

Looking at this, it seems the only important thing in that speed selection logic is how 2.5G is handled :

- either through the XGMII block when using USXGMII

   ctrl |= priv->hw->link.xgmii.speed2500;

- or through the regular speed selection bits :

   ctrl |= priv->hw->link.speed2500;

The rest is speed validation, and phylink should already be doing that for us.

I suggest that instead of this fix (that is ommiting the 5G case btw), we rewrite the whole ctrl assignment as :

	switch (speed) {
	case SPEED_100000:
		ctrl |= priv->hw->link.xlgmii.speed100000;
		break;
	case SPEED_50000:
		ctrl |= priv->hw->link.xlgmii.speed50000;
		break;
	case SPEED_40000:
		ctrl |= priv->hw->link.xlgmii.speed40000;
		break;
	case SPEED_25000:
		ctrl |= priv->hw->link.xlgmii.speed25000;
		break;
	case SPEED_10000:
		ctrl |= priv->hw->link.xgmii.speed10000;
		break;
	case SPEED_5000:
		ctrl |= priv->hw->link.xgmii.speed5000;
		break;
	case SPEED_2500:
		if (interface == PHY_INTERFACE_MODE_USXGMII)
			ctrl |= priv->hw->link.xgmii.speed2500;
		else
			ctrl |= priv->hw->link.speed2500;
		break;
	case SPEED_1000:
		ctrl |= priv->hw->link.speed1000;
	case SPEED_100:
		ctrl |= priv->hw->link.speed100;
		break;
	case SPEED_10:
		ctrl |= priv->hw->link.speed10;
		break;
	default:
		return;
	}

(I haven't tested that, I don't have any stmmac boards here that can do more than 1Gbps :( )

Thanks,

Maxime

#2 lore raw
Quoted 31 lines

I suggest that instead of this fix (that is ommiting the 5G case btw), we rewrite the whole ctrl assignment as :

	switch (speed) {
	case SPEED_100000:
		ctrl |= priv->hw->link.xlgmii.speed100000;
		break;
	case SPEED_50000:
		ctrl |= priv->hw->link.xlgmii.speed50000;
		break;
	case SPEED_40000:
		ctrl |= priv->hw->link.xlgmii.speed40000;
		break;
	case SPEED_25000:
		ctrl |= priv->hw->link.xlgmii.speed25000;
		break;
	case SPEED_10000:
		ctrl |= priv->hw->link.xgmii.speed10000;
		break;
	case SPEED_5000:
		ctrl |= priv->hw->link.xgmii.speed5000;
		break;
	case SPEED_2500:
		if (interface == PHY_INTERFACE_MODE_USXGMII)
			ctrl |= priv->hw->link.xgmii.speed2500;
		else
			ctrl |= priv->hw->link.speed2500;
		break;
	case SPEED_1000:
		ctrl |= priv->hw->link.speed1000;
	case SPEED_100:
Quoted 8 lines
		ctrl |= priv->hw->link.speed100;
		break;
	case SPEED_10:
		ctrl |= priv->hw->link.speed10;
		break;
	default:
		return;
	}

The bug description makes it sound like it was not obvious to debug. So maybe put an error message in the default: to aid the next developer who hits it with SPEED_14000, or whatever comes next.

Andrew

#3 lore raw

PATCH v2 1/1 net: stmmac: enable the MAC on link up for all supported speeds

In reply to vadik likholetov

stmmac_mac_link_down() clears the MAC's transmit and receive enable bits. stmmac_mac_link_up() is expected to set them again through stmmac_mac_set(..., true), but it first switches on the negotiated speed and returns early for a speed the switch does not list. The MAC is then left gated off.

The speed selection is split into three switches, keyed on the interface. The generic branch -- taken for everything that is neither USXGMII nor XLGMII, so including PHY_INTERFACE_MODE_10GBASER -- lists only SPEED_2500, SPEED_1000, SPEED_100 and SPEED_10.

MGBE on Tegra234 runs 10GBASE-R into an Aquantia AQR113C. That PHY does rate matching, so phylink_link_up() replaces the media speed with the MAC-side interface speed before calling into the MAC:

	case RATE_MATCH_PAUSE:
		speed = phylink_interface_max_speed(link_state.interface);
		duplex = DUPLEX_FULL;

The driver is therefore called as

	stmmac_mac_link_up(interface=10GBASER, speed=10000, duplex=1)

which falls through to "default: return;". The interface stops passing traffic after the first link flap.

The failure is easy to misread. The link still comes up, because the PHY is polled over MDIO and needs no MAC, so the interface reports carrier 1 at the media speed. The DMA is untouched, so its start bits stay set and descriptors are still consumed. Only the MAC itself is gated off: the receiver counts nothing (mmc_rx_framecount_gb stops advancing, RE is 0) and nothing reaches the wire (TE is 0). The interface survives boot only because stmmac_hw_setup(), called from ndo_open, enables the MAC unconditionally -- so the problem appears only once the cable has been unplugged and plugged back in, and "ip link set dev <ethX> down && ip link set dev <ethX> up" appears to fix it.

The interface is not what the speed bits depend on: with the single exception of 2.5G, which is selected through the XGMII block on USXGMII and through the regular speed bits otherwise, each speed maps to one field of struct mac_link. The per-interface switches are speed validation, and phylink already validates the speed against priv->hw->link.caps. So collapse the three switches into one keyed on the speed alone, keeping the interface test only for the 2.5G case. This covers 10G on 10GBASE-R, and equally 5G, and 1G/100/10 on USXGMII, all of which hit "default: return;" today.

A core that does not support a speed leaves the corresponding mac_link field at 0, and phylink will not offer it that speed in the first place. For dwxgmac2 at 10G, link.xgmii.speed10000 is XGMAC_CONFIG_SS_10000, which is 0 and is the correct speed selection for a 10GBASE-R MAC: ctrl then equals old_ctrl, the register write is skipped, and execution reaches stmmac_mac_set(..., true).

Log an error in the default case, since a speed with no entry here leaves the MAC disabled and the symptom does not point at the cause.

Fixes d8ca113724e7 ("net: stmmac: tegra: Add MGBE support")

---
v2:
- Collapse the three per-interface switches into a single switch on the speed, rather than adding SPEED_10000 to the generic branch, which left SPEED_5000 and the USXGMII sub-1G speeds broken (Maxime).
- netdev_err() in the default case (Andrew).

Fixes tag: the missing speeds predate the commit cited above. I picked d8ca113724e7 because MGBE is the first in-tree user to reach it -- it needs a 10GBASE-R interface driven by a rate-matching PHY, so that phylink hands the MAC a 10G speed. Happy to re-target it.

Verified on an AGX Orin devkit (Tegra234 MGBE0 + AQR113C), before and after, on the same board and cable. MAC registers read with ethtool -d, after a physical unplug and replug:

stock MAC_TX_CONFIG 0x00010000 (TE=0)

		MAC_RX_CONFIG 0x3ff022c0 (RE=0)
		rx_packets frozen, DHCP lease lost

patched MAC_TX_CONFIG 0x00010001 (TE=1)

		MAC_RX_CONFIG 0x3ff022c1 (RE=1)
		rx_packets keeps climbing, DHCP lease retained

Only the 10GBASE-R path is covered by hardware here; the other speeds are by inspection. Testing was done with MGBE0 handed to a VM via vfio-platform, so the driver ran in a guest; the MAC register evidence above is read from the device itself and the code path is not virtualisation-specific.

 .../net/ethernet/stmicro/stmmac/stmmac_main.c | 92 ++++++++-----------
 1 file changed, 37 insertions(+), 55 deletions(-)
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c +37 -55
index 2a0d7eff8..fa9f88e51 100644
@@ -1083,63 +1083,45 @@ static void stmmac_mac_link_up(struct phylink_config *config,
 	old_ctrl = readl(priv->ioaddr + MAC_CTRL_REG);
 	ctrl = old_ctrl & ~priv->hw->link.speed_mask;
 
-	if (interface == PHY_INTERFACE_MODE_USXGMII) {
-		switch (speed) {
-		case SPEED_10000:
-			ctrl |= priv->hw->link.xgmii.speed10000;
-			break;
-		case SPEED_5000:
-			ctrl |= priv->hw->link.xgmii.speed5000;
-			break;
-		case SPEED_2500:
+	switch (speed) {
+	case SPEED_100000:
+		ctrl |= priv->hw->link.xlgmii.speed100000;
+		break;
+	case SPEED_50000:
+		ctrl |= priv->hw->link.xlgmii.speed50000;
+		break;
+	case SPEED_40000:
+		ctrl |= priv->hw->link.xlgmii.speed40000;
+		break;
+	case SPEED_25000:
+		ctrl |= priv->hw->link.xlgmii.speed25000;
+		break;
+	case SPEED_10000:
+		ctrl |= priv->hw->link.xgmii.speed10000;
+		break;
+	case SPEED_5000:
+		ctrl |= priv->hw->link.xgmii.speed5000;
+		break;
+	case SPEED_2500:
+		if (interface == PHY_INTERFACE_MODE_USXGMII)
 			ctrl |= priv->hw->link.xgmii.speed2500;
-			break;
-		default:
-			return;
-		}
-	} else if (interface == PHY_INTERFACE_MODE_XLGMII) {
-		switch (speed) {
-		case SPEED_100000:
-			ctrl |= priv->hw->link.xlgmii.speed100000;
-			break;
-		case SPEED_50000:
-			ctrl |= priv->hw->link.xlgmii.speed50000;
-			break;
-		case SPEED_40000:
-			ctrl |= priv->hw->link.xlgmii.speed40000;
-			break;
-		case SPEED_25000:
-			ctrl |= priv->hw->link.xlgmii.speed25000;
-			break;
-		case SPEED_10000:
-			ctrl |= priv->hw->link.xgmii.speed10000;
-			break;
-		case SPEED_2500:
-			ctrl |= priv->hw->link.speed2500;
-			break;
-		case SPEED_1000:
-			ctrl |= priv->hw->link.speed1000;
-			break;
-		default:
-			return;
-		}
-	} else {
-		switch (speed) {
-		case SPEED_2500:
+		else
 			ctrl |= priv->hw->link.speed2500;
-			break;
-		case SPEED_1000:
-			ctrl |= priv->hw->link.speed1000;
-			break;
-		case SPEED_100:
-			ctrl |= priv->hw->link.speed100;
-			break;
-		case SPEED_10:
-			ctrl |= priv->hw->link.speed10;
-			break;
-		default:
-			return;
-		}
+		break;
+	case SPEED_1000:
+		ctrl |= priv->hw->link.speed1000;
+		break;
+	case SPEED_100:
+		ctrl |= priv->hw->link.speed100;
+		break;
+	case SPEED_10:
+		ctrl |= priv->hw->link.speed10;
+		break;
+	default:
+		netdev_err(priv->dev,
+			   "unsupported speed %d on %s, leaving the MAC disabled\n",
+			   speed, phy_modes(interface));
+		return;
 	}
 
 	if (priv->plat->fix_mac_speed)
Signature · 1 line
2.53.0
#4 lore raw

Re: [PATCH net v2] net: stmmac: enable the MAC on link up for all supported speeds

Hi,

When sending a new iteration, it should be a standalone thread, and not a reply to the previous version. Patchwork seems to have picked it up, so I _think_ it's ok for this one though :)

Quoted 184 lines · vadik likholetov

stmmac_mac_link_down() clears the MAC's transmit and receive enable bits. stmmac_mac_link_up() is expected to set them again through stmmac_mac_set(..., true), but it first switches on the negotiated speed and returns early for a speed the switch does not list. The MAC is then left gated off.

The speed selection is split into three switches, keyed on the interface. The generic branch -- taken for everything that is neither USXGMII nor XLGMII, so including PHY_INTERFACE_MODE_10GBASER -- lists only SPEED_2500, SPEED_1000, SPEED_100 and SPEED_10.

MGBE on Tegra234 runs 10GBASE-R into an Aquantia AQR113C. That PHY does rate matching, so phylink_link_up() replaces the media speed with the MAC-side interface speed before calling into the MAC:

	case RATE_MATCH_PAUSE:
		speed = phylink_interface_max_speed(link_state.interface);
		duplex = DUPLEX_FULL;

The driver is therefore called as

	stmmac_mac_link_up(interface=10GBASER, speed=10000, duplex=1)

which falls through to "default: return;". The interface stops passing traffic after the first link flap.

The failure is easy to misread. The link still comes up, because the PHY is polled over MDIO and needs no MAC, so the interface reports carrier 1 at the media speed. The DMA is untouched, so its start bits stay set and descriptors are still consumed. Only the MAC itself is gated off: the receiver counts nothing (mmc_rx_framecount_gb stops advancing, RE is 0) and nothing reaches the wire (TE is 0). The interface survives boot only because stmmac_hw_setup(), called from ndo_open, enables the MAC unconditionally -- so the problem appears only once the cable has been unplugged and plugged back in, and "ip link set dev <ethX> down && ip link set dev <ethX> up" appears to fix it.

The interface is not what the speed bits depend on: with the single exception of 2.5G, which is selected through the XGMII block on USXGMII and through the regular speed bits otherwise, each speed maps to one field of struct mac_link. The per-interface switches are speed validation, and phylink already validates the speed against priv->hw->link.caps. So collapse the three switches into one keyed on the speed alone, keeping the interface test only for the 2.5G case. This covers 10G on 10GBASE-R, and equally 5G, and 1G/100/10 on USXGMII, all of which hit "default: return;" today.

A core that does not support a speed leaves the corresponding mac_link field at 0, and phylink will not offer it that speed in the first place. For dwxgmac2 at 10G, link.xgmii.speed10000 is XGMAC_CONFIG_SS_10000, which is 0 and is the correct speed selection for a 10GBASE-R MAC: ctrl then equals old_ctrl, the register write is skipped, and execution reaches stmmac_mac_set(..., true).

Log an error in the default case, since a speed with no entry here leaves the MAC disabled and the symptom does not point at the cause.

Fixes d8ca113724e7 ("net: stmmac: tegra: Add MGBE support")

---
v2:
- Collapse the three per-interface switches into a single switch on the speed, rather than adding SPEED_10000 to the generic branch, which left SPEED_5000 and the USXGMII sub-1G speeds broken (Maxime).
- netdev_err() in the default case (Andrew).

Fixes tag: the missing speeds predate the commit cited above. I picked d8ca113724e7 because MGBE is the first in-tree user to reach it -- it needs a 10GBASE-R interface driven by a rate-matching PHY, so that phylink hands the MAC a 10G speed. Happy to re-target it.

Verified on an AGX Orin devkit (Tegra234 MGBE0 + AQR113C), before and after, on the same board and cable. MAC registers read with ethtool -d, after a physical unplug and replug:

stock MAC_TX_CONFIG 0x00010000 (TE=0)

		MAC_RX_CONFIG 0x3ff022c0 (RE=0)
		rx_packets frozen, DHCP lease lost

patched MAC_TX_CONFIG 0x00010001 (TE=1)

		MAC_RX_CONFIG 0x3ff022c1 (RE=1)
		rx_packets keeps climbing, DHCP lease retained

Only the 10GBASE-R path is covered by hardware here; the other speeds are by inspection. Testing was done with MGBE0 handed to a VM via vfio-platform, so the driver ran in a guest; the MAC register evidence above is read from the device itself and the code path is not virtualisation-specific.

 .../net/ethernet/stmicro/stmmac/stmmac_main.c | 92 ++++++++-----------
 1 file changed, 37 insertions(+), 55 deletions(-)
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c +26 -55
index 2a0d7eff8..fa9f88e51 100644
@@ -1083,63 +1083,45 @@ static void stmmac_mac_link_up(struct phylink_config *config,
 	old_ctrl = readl(priv->ioaddr + MAC_CTRL_REG);
 	ctrl = old_ctrl & ~priv->hw->link.speed_mask;
 
-	if (interface == PHY_INTERFACE_MODE_USXGMII) {
-		switch (speed) {
-		case SPEED_10000:
-			ctrl |= priv->hw->link.xgmii.speed10000;
-			break;
-		case SPEED_5000:
-			ctrl |= priv->hw->link.xgmii.speed5000;
-			break;
-		case SPEED_2500:
+	switch (speed) {
+	case SPEED_100000:
+		ctrl |= priv->hw->link.xlgmii.speed100000;
+		break;
+	case SPEED_50000:
+		ctrl |= priv->hw->link.xlgmii.speed50000;
+		break;
+	case SPEED_40000:
+		ctrl |= priv->hw->link.xlgmii.speed40000;
+		break;
+	case SPEED_25000:
+		ctrl |= priv->hw->link.xlgmii.speed25000;
+		break;
+	case SPEED_10000:
+		ctrl |= priv->hw->link.xgmii.speed10000;
+		break;
+	case SPEED_5000:
+		ctrl |= priv->hw->link.xgmii.speed5000;
+		break;
+	case SPEED_2500:
+		if (interface == PHY_INTERFACE_MODE_USXGMII)
 			ctrl |= priv->hw->link.xgmii.speed2500;
-			break;
-		default:
-			return;
-		}
-	} else if (interface == PHY_INTERFACE_MODE_XLGMII) {
-		switch (speed) {
-		case SPEED_100000:
-			ctrl |= priv->hw->link.xlgmii.speed100000;
-			break;
-		case SPEED_50000:
-			ctrl |= priv->hw->link.xlgmii.speed50000;
-			break;
-		case SPEED_40000:
-			ctrl |= priv->hw->link.xlgmii.speed40000;
-			break;
-		case SPEED_25000:
-			ctrl |= priv->hw->link.xlgmii.speed25000;
-			break;
-		case SPEED_10000:
-			ctrl |= priv->hw->link.xgmii.speed10000;
-			break;
-		case SPEED_2500:
-			ctrl |= priv->hw->link.speed2500;
-			break;
-		case SPEED_1000:
-			ctrl |= priv->hw->link.speed1000;
-			break;
-		default:
-			return;
-		}
-	} else {
-		switch (speed) {
-		case SPEED_2500:
+		else
 			ctrl |= priv->hw->link.speed2500;
-			break;
-		case SPEED_1000:
-			ctrl |= priv->hw->link.speed1000;
-			break;
-		case SPEED_100:
-			ctrl |= priv->hw->link.speed100;
-			break;
-		case SPEED_10:
-			ctrl |= priv->hw->link.speed10;
-			break;
-		default:
-			return;
-		}
+		break;
+	case SPEED_1000:
+		ctrl |= priv->hw->link.speed1000;
+		break;

drivers/net/ethernet/stmicro/stmmac/stmmac_main.c static void stmmac_mac_link_up(struct phylink_config *config, · line 1123

Quoted 10 lines
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c +10 -0
+	case SPEED_100:
+		ctrl |= priv->hw->link.speed100;
+		break;
+	case SPEED_10:
+		ctrl |= priv->hw->link.speed10;
+		break;
+	default:
+		netdev_err(priv->dev,
+			   "unsupported speed %d on %s, leaving the MAC disabled\n",
+			   speed, phy_modes(interface));

You should probably be using phy_speed_to_str() to print the speed.

Thanks,

Maxime