zynq/board.c: Add support for qspiboot and nandboot
PATCH 1/1 zynq/board.c: Add support for qspiboot and nandboot
The Zynq can also boot from QSPI or NAND, and environment scripting uses "qspiboot" and "nandboot" already. Add these to the board init routines so that modeboot is properly set to one of these values when the mode bits indicate so.
--- board/xilinx/zynq/board.c | 6 ++++++ 1 file changed, 6 insertions(+)
board/xilinx/zynq/board.c +6 -0
@@ -85,9 +85,15 @@ int board_init(void)int board_late_init (void ) {switch ((zynq_slcr_get_boot_mode ()) &ZYNQ_BM_MASK ) { +case ZYNQ_BM_QSPI : +setenv ("modeboot" ,"qspiboot" ); +break ;case ZYNQ_BM_NOR :setenv ("modeboot" ,"norboot" );break ; +case ZYNQ_BM_NAND : +setenv ("modeboot" ,"nandboot" ); +break ;case ZYNQ_BM_SD :setenv ("modeboot" ,"sdboot" );break ;
Signature · 1 line
1.9.1
PATCH 1/1 zynq/board.c: Add support for qspiboot and nandboot
Hi,
Quoted 21 lines · Mike Looijmans
The Zynq can also boot from QSPI or NAND, and environment scripting uses "qspiboot" and "nandboot" already. Add these to the board init routines so that modeboot is properly set to one of these values when the mode bits indicate so.
Signed-off-by Mike Looijmans <[email protected]>--- board/xilinx/zynq/board.c | 6 ++++++ 1 file changed, 6 insertions(+)board/xilinx/zynq/board.c +2
-0@@ -85,9 +85,15 @@ int board_init(void)int board_late_init (void ) {switch ((zynq_slcr_get_boot_mode ()) &ZYNQ_BM_MASK ) { +case ZYNQ_BM_QSPI : +setenv ("modeboot" ,"qspiboot" );
board/xilinx/zynq/board.c int board_init(void) · line 99
Quoted 10 lines
board/xilinx/zynq/board.c +4
-0+break ;case ZYNQ_BM_NOR :setenv ("modeboot" ,"norboot" );break ; +case ZYNQ_BM_NAND : +setenv ("modeboot" ,"nandboot" ); +break ;case ZYNQ_BM_SD :setenv ("modeboot" ,"sdboot" );break ;
The same patch was merged some days ago. Please check latest master branch.
Thanks,
Michal
PATCH 1/1 zynq/board.c: Add support for qspiboot and nandboot
?Ah, missed that. I noticed that "run $modeboot" didn't work for QSPI in the 2017.1 tag, hadn't seen that one yet.
Quoted 37 lines · Michal Simek
Hi,
Quoted 21 lines · Mike Looijmans
The Zynq can also boot from QSPI or NAND, and environment scripting uses "qspiboot" and "nandboot" already. Add these to the board init routines so that modeboot is properly set to one of these values when the mode bits indicate so.
Signed-off-by Mike Looijmans <[email protected]>--- board/xilinx/zynq/board.c | 6 ++++++ 1 file changed, 6 insertions(+)board/xilinx/zynq/board.c +2
-0@@ -85,9 +85,15 @@ int board_init(void)int board_late_init (void ) {switch ((zynq_slcr_get_boot_mode ()) &ZYNQ_BM_MASK ) { +case ZYNQ_BM_QSPI : +setenv ("modeboot" ,"qspiboot" );board/xilinx/zynq/board.c int board_init(void) · line 99
Quoted 10 lines
board/xilinx/zynq/board.c +4
-0+break ;case ZYNQ_BM_NOR :setenv ("modeboot" ,"norboot" );break ; +case ZYNQ_BM_NAND : +setenv ("modeboot" ,"nandboot" ); +break ;case ZYNQ_BM_SD :setenv ("modeboot" ,"sdboot" );break ;The same patch was merged some days ago. Please check latest master branch.
Quoted 3 lines
Thanks,
Michal
Kind regards,
Mike Looijmans
System Expert
TOPIC Products
Materiaalweg 4, NL-5681 RJ Best Postbus 440, NL-5680 AK Best
Telefoon: +31 (0) 499 33 69 79
E-mail: mike.looijmans at topicproducts.com
Website: www.topicproducts.com
Please consider the environment before printing this e-mail