gpio: Add Turris Omnia MCU driver
Subsystems (2)
PATCH 1/2 gpio: Add Turris Omnia MCU driver
This driver registers GPIO controller and allows U-Boot to control GPIO pins on MCU which is connected to Turris Omnia via i2c.
--- board/CZ.NIC/turris_omnia/MAINTAINERS | 1 + drivers/gpio/Kconfig | 7 + drivers/gpio/Makefile | 1 + drivers/gpio/turris_omnia_mcu.c | 314 ++++++++++++++++++++++++++ 4 files changed, 323 insertions(+) create mode 100644 drivers/gpio/turris_omnia_mcu.c
board/CZ.NIC/turris_omnia/MAINTAINERS +1 -0
@@ -6,4 +6,5 @@ F: arch/arm/dts/armada-385-turris-omnia*.dts* F: board/CZ.NIC/turris_atsha_otp.* F: board/CZ.NIC/turris_omnia/ F: configs/turris_omnia_defconfig +F: drivers/gpio/turris_omnia_mcu.c F: include/configs/turris_omnia.h
drivers/gpio/Kconfig +7 -0
@@ -598,4 +598,11 @@ config SLG7XL45106_I2C_GPO 8-bit gpo expander, all gpo lines are controlled by writing value into data register. +config TURRIS_OMNIA_MCU + bool "Turris Omnia MCU GPIO driver" + depends on DM_GPIO + default y if TARGET_TURRIS_OMNIA + help + Support for GPIOs on MCU connected to Turris Omnia via i2c. + endif
drivers/gpio/Makefile +1 -0
@@ -75,3 +75,4 @@ obj-$(CONFIG_MAX7320_GPIO) += max7320_gpio.o obj-$(CONFIG_SL28CPLD_GPIO) += sl28cpld-gpio.o obj-$(CONFIG_ZYNQMP_GPIO_MODEPIN) += zynqmp_gpio_modepin.o obj-$(CONFIG_SLG7XL45106_I2C_GPO) += gpio_slg7xl45106.o +obj-$(CONFIG_$(SPL_TPL_)TURRIS_OMNIA_MCU) += turris_omnia_mcu.o
drivers/gpio/turris_omnia_mcu.c new file +314 -0
314 lines not on this page · raw message
Signature · 1 line
2.20.1
PATCH 2/2 arm: mvebu: turris_omnia: Add mcu node with gpio-controller
This allows U-Boot to register new Turris Omnia MCU driver.
--- arch/arm/dts/armada-385-turris-omnia.dts | 8 +++++++- 1 file changed, 7 insertions(+), 1 deletion(-)
arch/arm/dts/armada-385-turris-omnia.dts +7 -1
@@ -173,7 +173,13 @@ #size-cells = <0>; reg = <0>; - /* STM32F0 command interface at address 0x2a */ + /* MCU command i2c API */ + mcu: mcu@2a { + compatible = "cznic,turris-omnia-mcu"; + reg = <0x2a>; + gpio-controller; + }; + /* leds device (in STM32F0) at address 0x2b */ eeprom@54 {
Signature · 1 line
2.20.1
Re: [PATCH 2/2] arm: mvebu: turris_omnia: Add mcu node with gpio-controller
Quoted 3 lines · Pali Rohár
This allows U-Boot to register new Turris Omnia MCU driver.
Signed-off-by Pali Rohár <[email protected]>
Thanks,
Stefan
Quoted 13 lines
--- arch/arm/dts/armada-385-turris-omnia.dts | 8 +++++++- 1 file changed, 7 insertions(+), 1 deletion(-)arch/arm/dts/armada-385-turris-omnia.dts +0
-1@@ -173,7 +173,13 @@ #size-cells = <0>; reg = <0>; - /* STM32F0 command interface at address 0x2a */
arch/arm/dts/armada-385-turris-omnia.dts line 185
Quoted 10 lines
arch/arm/dts/armada-385-turris-omnia.dts +7
-0+ /* MCU command i2c API */ + mcu: mcu@2a { + compatible = "cznic,turris-omnia-mcu"; + reg = <0x2a>; + gpio-controller; + }; + /* leds device (in STM32F0) at address 0x2b */ eeprom@54 {
Viele Grüße,
Stefan Roese
Signature · 3 lines
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: (+49)-8142-66989-51 Fax: (+49)-8142-66989-80 Email: [email protected]
Quoted 4 lines · Pali Rohár
This driver registers GPIO controller and allows U-Boot to control GPIO pins on MCU which is connected to Turris Omnia via i2c.
Signed-off-by Pali Rohár <[email protected]>
Thanks,
Stefan
Quoted 353 lines
--- board/CZ.NIC/turris_omnia/MAINTAINERS | 1 + drivers/gpio/Kconfig | 7 + drivers/gpio/Makefile | 1 + drivers/gpio/turris_omnia_mcu.c | 314 ++++++++++++++++++++++++++ 4 files changed, 323 insertions(+)create mode 100644
drivers/gpio/turris_omnia_mcu.cboard/CZ.NIC/turris_omnia/MAINTAINERS +1
-0@@ -6,4 +6,5 @@ F: arch/arm/dts/armada-385-turris-omnia*.dts* F: board/CZ.NIC/turris_atsha_otp.* F: board/CZ.NIC/turris_omnia/ F: configs/turris_omnia_defconfig +F: drivers/gpio/turris_omnia_mcu.c F: include/configs/turris_omnia.hdrivers/gpio/Kconfig +7
-0@@ -598,4 +598,11 @@ config SLG7XL45106_I2C_GPO 8-bit gpo expander, all gpo lines are controlled by writing value into data register. +config TURRIS_OMNIA_MCU + bool "Turris Omnia MCU GPIO driver" + depends on DM_GPIO + default y if TARGET_TURRIS_OMNIA + help + Support for GPIOs on MCU connected to Turris Omnia via i2c. + endifdrivers/gpio/Makefile +1
-0@@ -75,3 +75,4 @@ obj-$(CONFIG_MAX7320_GPIO) += max7320_gpio.o obj-$(CONFIG_SL28CPLD_GPIO) += sl28cpld-gpio.o obj-$(CONFIG_ZYNQMP_GPIO_MODEPIN) += zynqmp_gpio_modepin.o obj-$(CONFIG_SLG7XL45106_I2C_GPO) += gpio_slg7xl45106.o +obj-$(CONFIG_$(SPL_TPL_)TURRIS_OMNIA_MCU) += turris_omnia_mcu.odrivers/gpio/turris_omnia_mcu.c new file +304
-0@@ -0,0 +1,314 @@ +// SPDX-License-Identifier: GPL-2.0+ +// (C) 2022 Pali Rohár <[email protected]> + +#include <common.h> +#include <dm.h> +#include <i2c.h> +#include <asm/gpio.h> +#include <linux/log2.h> + +enum commands_e { +CMD_GET_STATUS_WORD =0x01 , +CMD_GENERAL_CONTROL =0x02 , + +/* available if STS_FEATURES_SUPPORTED bit set in status word */ +CMD_GET_FEATURES =0x10 , + +/* available if FEAT_EXT_CMDS bit is set in features */ +CMD_GET_EXT_STATUS_DWORD =0x11 , +CMD_EXT_CONTROL =0x12 , +CMD_GET_EXT_CONTROL_STATUS =0x13 , +}; + +/* CMD_GET_STATUS_WORD */ +enum sts_word_e { +STS_MCU_TYPE_MASK =GENMASK (1 ,0 ), +STS_MCU_TYPE_STM32 =0 , +STS_MCU_TYPE_GD32 =1 , +STS_MCU_TYPE_MKL =2 , +STS_FEATURES_SUPPORTED =BIT (2 ), +STS_USER_REGULATOR_NOT_SUPPORTED =BIT (3 ), +STS_CARD_DET =BIT (4 ), +STS_MSATA_IND =BIT (5 ), +STS_USB30_OVC =BIT (6 ), +STS_USB31_OVC =BIT (7 ), +STS_USB30_PWRON =BIT (8 ), +STS_USB31_PWRON =BIT (9 ), +STS_ENABLE_4V5 =BIT (10 ), +STS_BUTTON_MODE =BIT (11 ), +STS_BUTTON_PRESSED =BIT (12 ), +STS_BUTTON_COUNTER_MASK =GENMASK (15 ,13 ) +}; + +/* CMD_GENERAL_CONTROL */ +enum ctl_byte_e { +CTL_LIGHT_RST =BIT (0 ), +CTL_HARD_RST =BIT (1 ), +/*CTL_RESERVED = BIT(2),*/ +CTL_USB30_PWRON =BIT (3 ), +CTL_USB31_PWRON =BIT (4 ), +CTL_ENABLE_4V5 =BIT (5 ), +CTL_BUTTON_MODE =BIT (6 ), +CTL_BOOTLOADER =BIT (7 ) +}; + +/* CMD_GET_FEATURES */ +enum features_e { +FEAT_EXT_CMDS =BIT (1 ), +}; + +struct turris_omnia_mcu_info { +u16 features; +}; + +static int turris_omnia_mcu_get_function (struct udevice *dev,uint offset) +{ +struct turris_omnia_mcu_info *info =dev_get_plat (dev); + +switch (offset) { +/* bank 0 */ + case 0 ... 15: +switch (offset) { +case ilog2 (STS_USB30_PWRON ): +case ilog2 (STS_USB31_PWRON ): +case ilog2 (STS_ENABLE_4V5 ): +case ilog2 (STS_BUTTON_MODE ): +return GPIOF_OUTPUT ; +default : +return GPIOF_INPUT ; + } + +/* bank 1 - supported only when FEAT_EXT_CMDS is set */ + case (16 + 0) ... (16 + 31): +if (!(info->features &FEAT_EXT_CMDS )) +return -EINVAL ; +return GPIOF_INPUT ; + +/* bank 2 - supported only when FEAT_EXT_CMDS is set */ + case (16 + 32 + 0) ... (16 + 32 + 15): +if (!(info->features &FEAT_EXT_CMDS )) +return -EINVAL ; +return GPIOF_OUTPUT ; + +default : +return -EINVAL ; + } +} + +static int turris_omnia_mcu_get_value (struct udevice *dev,uint offset) +{ +struct turris_omnia_mcu_info *info =dev_get_plat (dev); +u8 val16[2 ]; +u8 val32[4 ]; +int ret; + +switch (offset) { +/* bank 0 */ + case 0 ... 15: + ret =dm_i2c_read (dev,CMD_GET_STATUS_WORD , val16,2 ); +if (ret) +return ret; +return ((((u16 )val16[1 ] <<8 ) | val16[0 ]) >> offset) &0x1 ; + +/* bank 1 - supported only when FEAT_EXT_CMDS is set */ + case (16 + 0) ... (16 + 31): +if (!(info->features &FEAT_EXT_CMDS )) +return -EINVAL ; + ret =dm_i2c_read (dev,CMD_GET_EXT_STATUS_DWORD , val32,4 ); +if (ret) +return ret; +return ((((u32 )val32[3 ] <<24 ) | ((u32 )val32[2 ] <<16 ) | + ((u32 )val32[1 ] <<8 ) | val32[0 ]) >> (offset -16 )) &0x1 ; + +/* bank 2 - supported only when FEAT_EXT_CMDS is set */ + case (16 + 32 + 0) ... (16 + 32 + 15): +if (!(info->features &FEAT_EXT_CMDS )) +return -EINVAL ; + ret =dm_i2c_read (dev,CMD_GET_EXT_CONTROL_STATUS , val16,2 ); +if (ret) +return ret; +return ((((u16 )val16[1 ] <<8 ) | val16[0 ]) >> (offset -16 -32 )) &0x1 ; + +default : +return -EINVAL ; + } +} + +static int turris_omnia_mcu_set_value (struct udevice *dev,uint offset,int value) +{ +struct turris_omnia_mcu_info *info =dev_get_plat (dev); +u8 val[2 ]; +int ret; +u8 reg; + +switch (offset) { +/* bank 0 */ +case ilog2 (STS_USB30_PWRON ): + reg =CMD_GENERAL_CONTROL ; + val[1 ] =CTL_USB30_PWRON ; +break ; +case ilog2 (STS_USB31_PWRON ): + reg =CMD_GENERAL_CONTROL ; + val[1 ] =CTL_USB31_PWRON ; +break ; +case ilog2 (STS_ENABLE_4V5 ): + reg =CMD_GENERAL_CONTROL ; + val[1 ] =CTL_ENABLE_4V5 ; +break ; +case ilog2 (STS_BUTTON_MODE ): + reg =CMD_GENERAL_CONTROL ; + val[1 ] =CTL_BUTTON_MODE ; +break ; + +/* bank 2 - supported only when FEAT_EXT_CMDS is set */ + case (16 + 32 + 0) ... (16 + 32 + 15): +if (!(info->features &FEAT_EXT_CMDS )) +return -EINVAL ; + reg =CMD_EXT_CONTROL ; + val[1 ] =BIT (offset -16 -32 ); +break ; + +default : +return -EINVAL ; + } + + val[0 ] = value ? val[1 ] :0 ; + + ret =dm_i2c_write (dev, reg, val,2 ); +if (ret) +return ret; + +return 0 ; +} + +static int turris_omnia_mcu_direction_input (struct udevice *dev,uint offset) +{ +int ret; + + ret =turris_omnia_mcu_get_function (dev, offset); +if (ret <0 ) +return ret; +else if (ret !=GPIOF_INPUT ) +return -EOPNOTSUPP ; + +return 0 ; +} + +static int turris_omnia_mcu_direction_output (struct udevice *dev,uint offset,int value) +{ +int ret; + + ret =turris_omnia_mcu_get_function (dev, offset); +if (ret <0 ) +return ret; +else if (ret !=GPIOF_OUTPUT ) +return -EOPNOTSUPP ; + +return turris_omnia_mcu_set_value (dev, offset, value); +} + +static int turris_omnia_mcu_xlate (struct udevice *dev,struct gpio_desc *desc, +struct ofnode_phandle_args *args) +{ +uint bank, gpio, flags, offset; +int ret; + +if (args->args_count !=3 ) +return -EINVAL ; + + bank = args->args[0 ]; + gpio = args->args[1 ]; + flags = args->args[2 ]; + +switch (bank) { +case 0 : +if (gpio >=16 ) +return -EINVAL ; + offset = gpio; +break ; +case 1 : +if (gpio >=32 ) +return -EINVAL ; + offset =16 + gpio; +break ; +case 2 : +if (gpio >=16 ) +return -EINVAL ; + offset =16 +32 + gpio; +break ; +default : +return -EINVAL ; + } + + ret =turris_omnia_mcu_get_function (dev, offset); +if (ret <0 ) +return ret; + +if (ret ==GPIOF_OUTPUT && ((flags &GPIOD_IS_IN ) || !(flags &GPIOD_IS_OUT ))) +return -EINVAL ; +else if (ret ==GPIOF_INPUT && (!(flags &GPIOD_IS_IN ) || (flags &GPIOD_IS_OUT ))) +return -EINVAL ; + + desc->offset = offset; + desc->flags = flags; + +return 0 ; +} + +static const struct dm_gpio_ops turris_omnia_mcu_ops = { + .direction_input = turris_omnia_mcu_direction_input, + .direction_output = turris_omnia_mcu_direction_output, + .get_value = turris_omnia_mcu_get_value, + .set_value = turris_omnia_mcu_set_value, + .get_function = turris_omnia_mcu_get_function, + .xlate = turris_omnia_mcu_xlate, +}; + +static int turris_omnia_mcu_probe (struct udevice *dev) +{ +struct turris_omnia_mcu_info *info =dev_get_plat (dev); +struct gpio_dev_priv *uc_priv =dev_get_uclass_priv (dev); +u16 status; +u8 val[2 ]; +int ret; + + ret =dm_i2c_read (dev,CMD_GET_STATUS_WORD , val,2 ); +if (ret) { +printf ("Error: turris_omnia_mcu CMD_GET_STATUS_WORD failed: %d\n" , ret); +return ret; + } + + status = ((u16 )val[1 ] <<8 ) | val[0 ]; + +if (status &STS_FEATURES_SUPPORTED ) { + ret =dm_i2c_read (dev,CMD_GET_FEATURES , val,2 ); +if (ret) { +printf ("Error: turris_omnia_mcu CMD_GET_FEATURES failed: %d\n" , ret); +return ret; + } + info->features = ((u16 )val[1 ] <<8 ) | val[0 ]; + } + + uc_priv->bank_name ="mcu_" ; + +if (info->features &FEAT_EXT_CMDS ) + uc_priv->gpio_count =16 +32 +16 ; +else + uc_priv->gpio_count =16 ; + +return 0 ; +} + +static const struct udevice_id turris_omnia_mcu_ids[] = { + { .compatible ="cznic,turris-omnia-mcu" }, + { }
drivers/gpio/turris_omnia_mcu.c line 314
Quoted 10 lines
drivers/gpio/turris_omnia_mcu.c new file +10
-0+}; + +U_BOOT_DRIVER (turris_omnia_mcu) = { + .name ="turris-omnia-mcu" , + .id =UCLASS_GPIO , + .ops = &turris_omnia_mcu_ops, + .probe = turris_omnia_mcu_probe, + .plat_auto =sizeof (struct turris_omnia_mcu_info ), + .of_match = turris_omnia_mcu_ids, +};
Viele Grüße,
Stefan Roese
Signature · 3 lines
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: (+49)-8142-66989-51 Fax: (+49)-8142-66989-80 Email: [email protected]
PATCH v2 1/2 gpio: Add Turris Omnia MCU driver
In reply to Pali RohárThis driver registers GPIO controller and allows U-Boot to control GPIO pins on MCU which is connected to Turris Omnia via i2c.
---
Changes in v2:
* Remove invalid checks in xlate (GPIOF_* vs GPIO_* macros)
* Fix parsing flags in xlate
* Use gpio_flags_xlate(flags) for desc->flags in xlate
--- board/CZ.NIC/turris_omnia/MAINTAINERS | 1 + drivers/gpio/Kconfig | 7 + drivers/gpio/Makefile | 1 + drivers/gpio/turris_omnia_mcu.c | 309 ++++++++++++++++++++++++++ 4 files changed, 318 insertions(+) create mode 100644 drivers/gpio/turris_omnia_mcu.c
board/CZ.NIC/turris_omnia/MAINTAINERS +1 -0
@@ -6,4 +6,5 @@ F: arch/arm/dts/armada-385-turris-omnia*.dts* F: board/CZ.NIC/turris_atsha_otp.* F: board/CZ.NIC/turris_omnia/ F: configs/turris_omnia_defconfig +F: drivers/gpio/turris_omnia_mcu.c F: include/configs/turris_omnia.h
drivers/gpio/Kconfig +7 -0
@@ -598,4 +598,11 @@ config SLG7XL45106_I2C_GPO 8-bit gpo expander, all gpo lines are controlled by writing value into data register. +config TURRIS_OMNIA_MCU + bool "Turris Omnia MCU GPIO driver" + depends on DM_GPIO + default y if TARGET_TURRIS_OMNIA + help + Support for GPIOs on MCU connected to Turris Omnia via i2c. + endif
drivers/gpio/Makefile +1 -0
@@ -75,3 +75,4 @@ obj-$(CONFIG_MAX7320_GPIO) += max7320_gpio.o obj-$(CONFIG_SL28CPLD_GPIO) += sl28cpld-gpio.o obj-$(CONFIG_ZYNQMP_GPIO_MODEPIN) += zynqmp_gpio_modepin.o obj-$(CONFIG_SLG7XL45106_I2C_GPO) += gpio_slg7xl45106.o +obj-$(CONFIG_$(SPL_TPL_)TURRIS_OMNIA_MCU) += turris_omnia_mcu.o
drivers/gpio/turris_omnia_mcu.c new file +309 -0
309 lines not on this page · raw message
Signature · 1 line
2.20.1
PATCH v2 2/2 arm: mvebu: turris_omnia: Add mcu node with gpio-controller
This allows U-Boot to register new Turris Omnia MCU driver.
---
Changes in v2:
* Add missing #gpio-cells for phandle usage
--- arch/arm/dts/armada-385-turris-omnia.dts | 9 ++++++++- 1 file changed, 8 insertions(+), 1 deletion(-)
arch/arm/dts/armada-385-turris-omnia.dts +8 -1
@@ -173,7 +173,14 @@ #size-cells = <0>; reg = <0>; - /* STM32F0 command interface at address 0x2a */ + /* MCU command i2c API */ + mcu: mcu@2a { + compatible = "cznic,turris-omnia-mcu"; + reg = <0x2a>; + gpio-controller; + #gpio-cells = <3>; + }; + /* leds device (in STM32F0) at address 0x2b */ eeprom@54 {
Signature · 1 line
2.20.1
Re: [PATCH v2 2/2] arm: mvebu: turris_omnia: Add mcu node with gpio-controller
Quoted 3 lines · Pali Rohár
This allows U-Boot to register new Turris Omnia MCU driver.
Signed-off-by Pali Rohár <[email protected]>
Thanks,
Stefan
Quoted 17 lines
---
Changes in v2:
* Add missing #gpio-cells for phandle usage--- arch/arm/dts/armada-385-turris-omnia.dts | 9 ++++++++- 1 file changed, 8 insertions(+), 1 deletion(-)arch/arm/dts/armada-385-turris-omnia.dts +1
-1@@ -173,7 +173,14 @@ #size-cells = <0>; reg = <0>; - /* STM32F0 command interface at address 0x2a */ + /* MCU command i2c API */
arch/arm/dts/armada-385-turris-omnia.dts line 186
Quoted 10 lines
arch/arm/dts/armada-385-turris-omnia.dts +7
-0+ mcu: mcu@2a { + compatible = "cznic,turris-omnia-mcu"; + reg = <0x2a>; + gpio-controller; + #gpio-cells = <3>; + }; + /* leds device (in STM32F0) at address 0x2b */ eeprom@54 {
Viele Grüße,
Stefan Roese
Signature · 3 lines
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: (+49)-8142-66989-51 Fax: (+49)-8142-66989-80 Email: [email protected]
Re: [PATCH v2 2/2] arm: mvebu: turris_omnia: Add mcu node with gpio-controller
In reply to Pali RohárQuoted 3 lines · Pali Rohár
This allows U-Boot to register new Turris Omnia MCU driver.
Signed-off-by Pali Rohár <[email protected]>
Applied to u-boot-marvell/master
Thanks,
Stefan
Quoted 17 lines
---
Changes in v2:
* Add missing #gpio-cells for phandle usage--- arch/arm/dts/armada-385-turris-omnia.dts | 9 ++++++++- 1 file changed, 8 insertions(+), 1 deletion(-)arch/arm/dts/armada-385-turris-omnia.dts +1
-1@@ -173,7 +173,14 @@ #size-cells = <0>; reg = <0>; - /* STM32F0 command interface at address 0x2a */ + /* MCU command i2c API */
arch/arm/dts/armada-385-turris-omnia.dts line 186
Quoted 10 lines
arch/arm/dts/armada-385-turris-omnia.dts +7
-0+ mcu: mcu@2a { + compatible = "cznic,turris-omnia-mcu"; + reg = <0x2a>; + gpio-controller; + #gpio-cells = <3>; + }; + /* leds device (in STM32F0) at address 0x2b */ eeprom@54 {
Viele Grüße,
Stefan Roese
Signature · 3 lines
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: (+49)-8142-66989-51 Fax: (+49)-8142-66989-80 Email: [email protected]
Quoted 4 lines · Pali Rohár
This driver registers GPIO controller and allows U-Boot to control GPIO pins on MCU which is connected to Turris Omnia via i2c.
Signed-off-by Pali Rohár <[email protected]>
Thanks,
Stefan
Quoted 353 lines
---
Changes in v2:
* Remove invalid checks in xlate (GPIOF_* vs GPIO_* macros)
* Fix parsing flags in xlate
* Usegpio_flags_xlate(flags)fordesc->flagsin xlate--- board/CZ.NIC/turris_omnia/MAINTAINERS | 1 + drivers/gpio/Kconfig | 7 + drivers/gpio/Makefile | 1 + drivers/gpio/turris_omnia_mcu.c | 309 ++++++++++++++++++++++++++ 4 files changed, 318 insertions(+)create mode 100644
drivers/gpio/turris_omnia_mcu.cboard/CZ.NIC/turris_omnia/MAINTAINERS +1
-0@@ -6,4 +6,5 @@ F: arch/arm/dts/armada-385-turris-omnia*.dts* F: board/CZ.NIC/turris_atsha_otp.* F: board/CZ.NIC/turris_omnia/ F: configs/turris_omnia_defconfig +F: drivers/gpio/turris_omnia_mcu.c F: include/configs/turris_omnia.hdrivers/gpio/Kconfig +7
-0@@ -598,4 +598,11 @@ config SLG7XL45106_I2C_GPO 8-bit gpo expander, all gpo lines are controlled by writing value into data register. +config TURRIS_OMNIA_MCU + bool "Turris Omnia MCU GPIO driver" + depends on DM_GPIO + default y if TARGET_TURRIS_OMNIA + help + Support for GPIOs on MCU connected to Turris Omnia via i2c. + endifdrivers/gpio/Makefile +1
-0@@ -75,3 +75,4 @@ obj-$(CONFIG_MAX7320_GPIO) += max7320_gpio.o obj-$(CONFIG_SL28CPLD_GPIO) += sl28cpld-gpio.o obj-$(CONFIG_ZYNQMP_GPIO_MODEPIN) += zynqmp_gpio_modepin.o obj-$(CONFIG_SLG7XL45106_I2C_GPO) += gpio_slg7xl45106.o +obj-$(CONFIG_$(SPL_TPL_)TURRIS_OMNIA_MCU) += turris_omnia_mcu.odrivers/gpio/turris_omnia_mcu.c new file +299
-0@@ -0,0 +1,309 @@ +// SPDX-License-Identifier: GPL-2.0+ +// (C) 2022 Pali Rohár <[email protected]> + +#include <common.h> +#include <dm.h> +#include <i2c.h> +#include <asm/gpio.h> +#include <linux/log2.h> + +enum commands_e { +CMD_GET_STATUS_WORD =0x01 , +CMD_GENERAL_CONTROL =0x02 , + +/* available if STS_FEATURES_SUPPORTED bit set in status word */ +CMD_GET_FEATURES =0x10 , + +/* available if FEAT_EXT_CMDS bit is set in features */ +CMD_GET_EXT_STATUS_DWORD =0x11 , +CMD_EXT_CONTROL =0x12 , +CMD_GET_EXT_CONTROL_STATUS =0x13 , +}; + +/* CMD_GET_STATUS_WORD */ +enum sts_word_e { +STS_MCU_TYPE_MASK =GENMASK (1 ,0 ), +STS_MCU_TYPE_STM32 =0 , +STS_MCU_TYPE_GD32 =1 , +STS_MCU_TYPE_MKL =2 , +STS_FEATURES_SUPPORTED =BIT (2 ), +STS_USER_REGULATOR_NOT_SUPPORTED =BIT (3 ), +STS_CARD_DET =BIT (4 ), +STS_MSATA_IND =BIT (5 ), +STS_USB30_OVC =BIT (6 ), +STS_USB31_OVC =BIT (7 ), +STS_USB30_PWRON =BIT (8 ), +STS_USB31_PWRON =BIT (9 ), +STS_ENABLE_4V5 =BIT (10 ), +STS_BUTTON_MODE =BIT (11 ), +STS_BUTTON_PRESSED =BIT (12 ), +STS_BUTTON_COUNTER_MASK =GENMASK (15 ,13 ) +}; + +/* CMD_GENERAL_CONTROL */ +enum ctl_byte_e { +CTL_LIGHT_RST =BIT (0 ), +CTL_HARD_RST =BIT (1 ), +/*CTL_RESERVED = BIT(2),*/ +CTL_USB30_PWRON =BIT (3 ), +CTL_USB31_PWRON =BIT (4 ), +CTL_ENABLE_4V5 =BIT (5 ), +CTL_BUTTON_MODE =BIT (6 ), +CTL_BOOTLOADER =BIT (7 ) +}; + +/* CMD_GET_FEATURES */ +enum features_e { +FEAT_EXT_CMDS =BIT (1 ), +}; + +struct turris_omnia_mcu_info { +u16 features; +}; + +static int turris_omnia_mcu_get_function (struct udevice *dev,uint offset) +{ +struct turris_omnia_mcu_info *info =dev_get_plat (dev); + +switch (offset) { +/* bank 0 */ + case 0 ... 15: +switch (offset) { +case ilog2 (STS_USB30_PWRON ): +case ilog2 (STS_USB31_PWRON ): +case ilog2 (STS_ENABLE_4V5 ): +case ilog2 (STS_BUTTON_MODE ): +return GPIOF_OUTPUT ; +default : +return GPIOF_INPUT ; + } + +/* bank 1 - supported only when FEAT_EXT_CMDS is set */ + case (16 + 0) ... (16 + 31): +if (!(info->features &FEAT_EXT_CMDS )) +return -EINVAL ; +return GPIOF_INPUT ; + +/* bank 2 - supported only when FEAT_EXT_CMDS is set */ + case (16 + 32 + 0) ... (16 + 32 + 15): +if (!(info->features &FEAT_EXT_CMDS )) +return -EINVAL ; +return GPIOF_OUTPUT ; + +default : +return -EINVAL ; + } +} + +static int turris_omnia_mcu_get_value (struct udevice *dev,uint offset) +{ +struct turris_omnia_mcu_info *info =dev_get_plat (dev); +u8 val16[2 ]; +u8 val32[4 ]; +int ret; + +switch (offset) { +/* bank 0 */ + case 0 ... 15: + ret =dm_i2c_read (dev,CMD_GET_STATUS_WORD , val16,2 ); +if (ret) +return ret; +return ((((u16 )val16[1 ] <<8 ) | val16[0 ]) >> offset) &0x1 ; + +/* bank 1 - supported only when FEAT_EXT_CMDS is set */ + case (16 + 0) ... (16 + 31): +if (!(info->features &FEAT_EXT_CMDS )) +return -EINVAL ; + ret =dm_i2c_read (dev,CMD_GET_EXT_STATUS_DWORD , val32,4 ); +if (ret) +return ret; +return ((((u32 )val32[3 ] <<24 ) | ((u32 )val32[2 ] <<16 ) | + ((u32 )val32[1 ] <<8 ) | val32[0 ]) >> (offset -16 )) &0x1 ; + +/* bank 2 - supported only when FEAT_EXT_CMDS is set */ + case (16 + 32 + 0) ... (16 + 32 + 15): +if (!(info->features &FEAT_EXT_CMDS )) +return -EINVAL ; + ret =dm_i2c_read (dev,CMD_GET_EXT_CONTROL_STATUS , val16,2 ); +if (ret) +return ret; +return ((((u16 )val16[1 ] <<8 ) | val16[0 ]) >> (offset -16 -32 )) &0x1 ; + +default : +return -EINVAL ; + } +} + +static int turris_omnia_mcu_set_value (struct udevice *dev,uint offset,int value) +{ +struct turris_omnia_mcu_info *info =dev_get_plat (dev); +u8 val[2 ]; +int ret; +u8 reg; + +switch (offset) { +/* bank 0 */ +case ilog2 (STS_USB30_PWRON ): + reg =CMD_GENERAL_CONTROL ; + val[1 ] =CTL_USB30_PWRON ; +break ; +case ilog2 (STS_USB31_PWRON ): + reg =CMD_GENERAL_CONTROL ; + val[1 ] =CTL_USB31_PWRON ; +break ; +case ilog2 (STS_ENABLE_4V5 ): + reg =CMD_GENERAL_CONTROL ; + val[1 ] =CTL_ENABLE_4V5 ; +break ; +case ilog2 (STS_BUTTON_MODE ): + reg =CMD_GENERAL_CONTROL ; + val[1 ] =CTL_BUTTON_MODE ; +break ; + +/* bank 2 - supported only when FEAT_EXT_CMDS is set */ + case (16 + 32 + 0) ... (16 + 32 + 15): +if (!(info->features &FEAT_EXT_CMDS )) +return -EINVAL ; + reg =CMD_EXT_CONTROL ; + val[1 ] =BIT (offset -16 -32 ); +break ; + +default : +return -EINVAL ; + } + + val[0 ] = value ? val[1 ] :0 ; + + ret =dm_i2c_write (dev, reg, val,2 ); +if (ret) +return ret; + +return 0 ; +} + +static int turris_omnia_mcu_direction_input (struct udevice *dev,uint offset) +{ +int ret; + + ret =turris_omnia_mcu_get_function (dev, offset); +if (ret <0 ) +return ret; +else if (ret !=GPIOF_INPUT ) +return -EOPNOTSUPP ; + +return 0 ; +} + +static int turris_omnia_mcu_direction_output (struct udevice *dev,uint offset,int value) +{ +int ret; + + ret =turris_omnia_mcu_get_function (dev, offset); +if (ret <0 ) +return ret; +else if (ret !=GPIOF_OUTPUT ) +return -EOPNOTSUPP ; + +return turris_omnia_mcu_set_value (dev, offset, value); +} + +static int turris_omnia_mcu_xlate (struct udevice *dev,struct gpio_desc *desc, +struct ofnode_phandle_args *args) +{ +uint bank, gpio, flags, offset; +int ret; + +if (args->args_count !=3 ) +return -EINVAL ; + + bank = args->args[0 ]; + gpio = args->args[1 ]; + flags = args->args[2 ]; + +switch (bank) { +case 0 : +if (gpio >=16 ) +return -EINVAL ; + offset = gpio; +break ; +case 1 : +if (gpio >=32 ) +return -EINVAL ; + offset =16 + gpio; +break ; +case 2 : +if (gpio >=16 ) +return -EINVAL ; + offset =16 +32 + gpio; +break ; +default : +return -EINVAL ; + } + + ret =turris_omnia_mcu_get_function (dev, offset); +if (ret <0 ) +return ret; + + desc->offset = offset; + desc->flags =gpio_flags_xlate (flags); + +return 0 ; +} + +static const struct dm_gpio_ops turris_omnia_mcu_ops = { + .direction_input = turris_omnia_mcu_direction_input, + .direction_output = turris_omnia_mcu_direction_output, + .get_value = turris_omnia_mcu_get_value, + .set_value = turris_omnia_mcu_set_value, + .get_function = turris_omnia_mcu_get_function, + .xlate = turris_omnia_mcu_xlate, +}; + +static int turris_omnia_mcu_probe (struct udevice *dev) +{ +struct turris_omnia_mcu_info *info =dev_get_plat (dev); +struct gpio_dev_priv *uc_priv =dev_get_uclass_priv (dev); +u16 status; +u8 val[2 ]; +int ret; + + ret =dm_i2c_read (dev,CMD_GET_STATUS_WORD , val,2 ); +if (ret) { +printf ("Error: turris_omnia_mcu CMD_GET_STATUS_WORD failed: %d\n" , ret); +return ret; + } + + status = ((u16 )val[1 ] <<8 ) | val[0 ]; + +if (status &STS_FEATURES_SUPPORTED ) { + ret =dm_i2c_read (dev,CMD_GET_FEATURES , val,2 ); +if (ret) { +printf ("Error: turris_omnia_mcu CMD_GET_FEATURES failed: %d\n" , ret); +return ret; + } + info->features = ((u16 )val[1 ] <<8 ) | val[0 ]; + } + + uc_priv->bank_name ="mcu_" ; + +if (info->features &FEAT_EXT_CMDS ) + uc_priv->gpio_count =16 +32 +16 ; +else + uc_priv->gpio_count =16 ; + +return 0 ; +} + +static const struct udevice_id turris_omnia_mcu_ids[] = { + { .compatible ="cznic,turris-omnia-mcu" }, + { }
drivers/gpio/turris_omnia_mcu.c line 309
Quoted 10 lines
drivers/gpio/turris_omnia_mcu.c new file +10
-0+}; + +U_BOOT_DRIVER (turris_omnia_mcu) = { + .name ="turris-omnia-mcu" , + .id =UCLASS_GPIO , + .ops = &turris_omnia_mcu_ops, + .probe = turris_omnia_mcu_probe, + .plat_auto =sizeof (struct turris_omnia_mcu_info ), + .of_match = turris_omnia_mcu_ids, +};
Viele Grüße,
Stefan Roese
Signature · 3 lines
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: (+49)-8142-66989-51 Fax: (+49)-8142-66989-80 Email: [email protected]
Quoted 4 lines · Pali Rohár
This driver registers GPIO controller and allows U-Boot to control GPIO pins on MCU which is connected to Turris Omnia via i2c.
Signed-off-by Pali Rohár <[email protected]>
Applied to u-boot-marvell/master
Thanks,
Stefan
Quoted 353 lines
---
Changes in v2:
* Remove invalid checks in xlate (GPIOF_* vs GPIO_* macros)
* Fix parsing flags in xlate
* Usegpio_flags_xlate(flags)fordesc->flagsin xlate--- board/CZ.NIC/turris_omnia/MAINTAINERS | 1 + drivers/gpio/Kconfig | 7 + drivers/gpio/Makefile | 1 + drivers/gpio/turris_omnia_mcu.c | 309 ++++++++++++++++++++++++++ 4 files changed, 318 insertions(+)create mode 100644
drivers/gpio/turris_omnia_mcu.cboard/CZ.NIC/turris_omnia/MAINTAINERS +1
-0@@ -6,4 +6,5 @@ F: arch/arm/dts/armada-385-turris-omnia*.dts* F: board/CZ.NIC/turris_atsha_otp.* F: board/CZ.NIC/turris_omnia/ F: configs/turris_omnia_defconfig +F: drivers/gpio/turris_omnia_mcu.c F: include/configs/turris_omnia.hdrivers/gpio/Kconfig +7
-0@@ -598,4 +598,11 @@ config SLG7XL45106_I2C_GPO 8-bit gpo expander, all gpo lines are controlled by writing value into data register. +config TURRIS_OMNIA_MCU + bool "Turris Omnia MCU GPIO driver" + depends on DM_GPIO + default y if TARGET_TURRIS_OMNIA + help + Support for GPIOs on MCU connected to Turris Omnia via i2c. + endifdrivers/gpio/Makefile +1
-0@@ -75,3 +75,4 @@ obj-$(CONFIG_MAX7320_GPIO) += max7320_gpio.o obj-$(CONFIG_SL28CPLD_GPIO) += sl28cpld-gpio.o obj-$(CONFIG_ZYNQMP_GPIO_MODEPIN) += zynqmp_gpio_modepin.o obj-$(CONFIG_SLG7XL45106_I2C_GPO) += gpio_slg7xl45106.o +obj-$(CONFIG_$(SPL_TPL_)TURRIS_OMNIA_MCU) += turris_omnia_mcu.odrivers/gpio/turris_omnia_mcu.c new file +299
-0@@ -0,0 +1,309 @@ +// SPDX-License-Identifier: GPL-2.0+ +// (C) 2022 Pali Rohár <[email protected]> + +#include <common.h> +#include <dm.h> +#include <i2c.h> +#include <asm/gpio.h> +#include <linux/log2.h> + +enum commands_e { +CMD_GET_STATUS_WORD =0x01 , +CMD_GENERAL_CONTROL =0x02 , + +/* available if STS_FEATURES_SUPPORTED bit set in status word */ +CMD_GET_FEATURES =0x10 , + +/* available if FEAT_EXT_CMDS bit is set in features */ +CMD_GET_EXT_STATUS_DWORD =0x11 , +CMD_EXT_CONTROL =0x12 , +CMD_GET_EXT_CONTROL_STATUS =0x13 , +}; + +/* CMD_GET_STATUS_WORD */ +enum sts_word_e { +STS_MCU_TYPE_MASK =GENMASK (1 ,0 ), +STS_MCU_TYPE_STM32 =0 , +STS_MCU_TYPE_GD32 =1 , +STS_MCU_TYPE_MKL =2 , +STS_FEATURES_SUPPORTED =BIT (2 ), +STS_USER_REGULATOR_NOT_SUPPORTED =BIT (3 ), +STS_CARD_DET =BIT (4 ), +STS_MSATA_IND =BIT (5 ), +STS_USB30_OVC =BIT (6 ), +STS_USB31_OVC =BIT (7 ), +STS_USB30_PWRON =BIT (8 ), +STS_USB31_PWRON =BIT (9 ), +STS_ENABLE_4V5 =BIT (10 ), +STS_BUTTON_MODE =BIT (11 ), +STS_BUTTON_PRESSED =BIT (12 ), +STS_BUTTON_COUNTER_MASK =GENMASK (15 ,13 ) +}; + +/* CMD_GENERAL_CONTROL */ +enum ctl_byte_e { +CTL_LIGHT_RST =BIT (0 ), +CTL_HARD_RST =BIT (1 ), +/*CTL_RESERVED = BIT(2),*/ +CTL_USB30_PWRON =BIT (3 ), +CTL_USB31_PWRON =BIT (4 ), +CTL_ENABLE_4V5 =BIT (5 ), +CTL_BUTTON_MODE =BIT (6 ), +CTL_BOOTLOADER =BIT (7 ) +}; + +/* CMD_GET_FEATURES */ +enum features_e { +FEAT_EXT_CMDS =BIT (1 ), +}; + +struct turris_omnia_mcu_info { +u16 features; +}; + +static int turris_omnia_mcu_get_function (struct udevice *dev,uint offset) +{ +struct turris_omnia_mcu_info *info =dev_get_plat (dev); + +switch (offset) { +/* bank 0 */ + case 0 ... 15: +switch (offset) { +case ilog2 (STS_USB30_PWRON ): +case ilog2 (STS_USB31_PWRON ): +case ilog2 (STS_ENABLE_4V5 ): +case ilog2 (STS_BUTTON_MODE ): +return GPIOF_OUTPUT ; +default : +return GPIOF_INPUT ; + } + +/* bank 1 - supported only when FEAT_EXT_CMDS is set */ + case (16 + 0) ... (16 + 31): +if (!(info->features &FEAT_EXT_CMDS )) +return -EINVAL ; +return GPIOF_INPUT ; + +/* bank 2 - supported only when FEAT_EXT_CMDS is set */ + case (16 + 32 + 0) ... (16 + 32 + 15): +if (!(info->features &FEAT_EXT_CMDS )) +return -EINVAL ; +return GPIOF_OUTPUT ; + +default : +return -EINVAL ; + } +} + +static int turris_omnia_mcu_get_value (struct udevice *dev,uint offset) +{ +struct turris_omnia_mcu_info *info =dev_get_plat (dev); +u8 val16[2 ]; +u8 val32[4 ]; +int ret; + +switch (offset) { +/* bank 0 */ + case 0 ... 15: + ret =dm_i2c_read (dev,CMD_GET_STATUS_WORD , val16,2 ); +if (ret) +return ret; +return ((((u16 )val16[1 ] <<8 ) | val16[0 ]) >> offset) &0x1 ; + +/* bank 1 - supported only when FEAT_EXT_CMDS is set */ + case (16 + 0) ... (16 + 31): +if (!(info->features &FEAT_EXT_CMDS )) +return -EINVAL ; + ret =dm_i2c_read (dev,CMD_GET_EXT_STATUS_DWORD , val32,4 ); +if (ret) +return ret; +return ((((u32 )val32[3 ] <<24 ) | ((u32 )val32[2 ] <<16 ) | + ((u32 )val32[1 ] <<8 ) | val32[0 ]) >> (offset -16 )) &0x1 ; + +/* bank 2 - supported only when FEAT_EXT_CMDS is set */ + case (16 + 32 + 0) ... (16 + 32 + 15): +if (!(info->features &FEAT_EXT_CMDS )) +return -EINVAL ; + ret =dm_i2c_read (dev,CMD_GET_EXT_CONTROL_STATUS , val16,2 ); +if (ret) +return ret; +return ((((u16 )val16[1 ] <<8 ) | val16[0 ]) >> (offset -16 -32 )) &0x1 ; + +default : +return -EINVAL ; + } +} + +static int turris_omnia_mcu_set_value (struct udevice *dev,uint offset,int value) +{ +struct turris_omnia_mcu_info *info =dev_get_plat (dev); +u8 val[2 ]; +int ret; +u8 reg; + +switch (offset) { +/* bank 0 */ +case ilog2 (STS_USB30_PWRON ): + reg =CMD_GENERAL_CONTROL ; + val[1 ] =CTL_USB30_PWRON ; +break ; +case ilog2 (STS_USB31_PWRON ): + reg =CMD_GENERAL_CONTROL ; + val[1 ] =CTL_USB31_PWRON ; +break ; +case ilog2 (STS_ENABLE_4V5 ): + reg =CMD_GENERAL_CONTROL ; + val[1 ] =CTL_ENABLE_4V5 ; +break ; +case ilog2 (STS_BUTTON_MODE ): + reg =CMD_GENERAL_CONTROL ; + val[1 ] =CTL_BUTTON_MODE ; +break ; + +/* bank 2 - supported only when FEAT_EXT_CMDS is set */ + case (16 + 32 + 0) ... (16 + 32 + 15): +if (!(info->features &FEAT_EXT_CMDS )) +return -EINVAL ; + reg =CMD_EXT_CONTROL ; + val[1 ] =BIT (offset -16 -32 ); +break ; + +default : +return -EINVAL ; + } + + val[0 ] = value ? val[1 ] :0 ; + + ret =dm_i2c_write (dev, reg, val,2 ); +if (ret) +return ret; + +return 0 ; +} + +static int turris_omnia_mcu_direction_input (struct udevice *dev,uint offset) +{ +int ret; + + ret =turris_omnia_mcu_get_function (dev, offset); +if (ret <0 ) +return ret; +else if (ret !=GPIOF_INPUT ) +return -EOPNOTSUPP ; + +return 0 ; +} + +static int turris_omnia_mcu_direction_output (struct udevice *dev,uint offset,int value) +{ +int ret; + + ret =turris_omnia_mcu_get_function (dev, offset); +if (ret <0 ) +return ret; +else if (ret !=GPIOF_OUTPUT ) +return -EOPNOTSUPP ; + +return turris_omnia_mcu_set_value (dev, offset, value); +} + +static int turris_omnia_mcu_xlate (struct udevice *dev,struct gpio_desc *desc, +struct ofnode_phandle_args *args) +{ +uint bank, gpio, flags, offset; +int ret; + +if (args->args_count !=3 ) +return -EINVAL ; + + bank = args->args[0 ]; + gpio = args->args[1 ]; + flags = args->args[2 ]; + +switch (bank) { +case 0 : +if (gpio >=16 ) +return -EINVAL ; + offset = gpio; +break ; +case 1 : +if (gpio >=32 ) +return -EINVAL ; + offset =16 + gpio; +break ; +case 2 : +if (gpio >=16 ) +return -EINVAL ; + offset =16 +32 + gpio; +break ; +default : +return -EINVAL ; + } + + ret =turris_omnia_mcu_get_function (dev, offset); +if (ret <0 ) +return ret; + + desc->offset = offset; + desc->flags =gpio_flags_xlate (flags); + +return 0 ; +} + +static const struct dm_gpio_ops turris_omnia_mcu_ops = { + .direction_input = turris_omnia_mcu_direction_input, + .direction_output = turris_omnia_mcu_direction_output, + .get_value = turris_omnia_mcu_get_value, + .set_value = turris_omnia_mcu_set_value, + .get_function = turris_omnia_mcu_get_function, + .xlate = turris_omnia_mcu_xlate, +}; + +static int turris_omnia_mcu_probe (struct udevice *dev) +{ +struct turris_omnia_mcu_info *info =dev_get_plat (dev); +struct gpio_dev_priv *uc_priv =dev_get_uclass_priv (dev); +u16 status; +u8 val[2 ]; +int ret; + + ret =dm_i2c_read (dev,CMD_GET_STATUS_WORD , val,2 ); +if (ret) { +printf ("Error: turris_omnia_mcu CMD_GET_STATUS_WORD failed: %d\n" , ret); +return ret; + } + + status = ((u16 )val[1 ] <<8 ) | val[0 ]; + +if (status &STS_FEATURES_SUPPORTED ) { + ret =dm_i2c_read (dev,CMD_GET_FEATURES , val,2 ); +if (ret) { +printf ("Error: turris_omnia_mcu CMD_GET_FEATURES failed: %d\n" , ret); +return ret; + } + info->features = ((u16 )val[1 ] <<8 ) | val[0 ]; + } + + uc_priv->bank_name ="mcu_" ; + +if (info->features &FEAT_EXT_CMDS ) + uc_priv->gpio_count =16 +32 +16 ; +else + uc_priv->gpio_count =16 ; + +return 0 ; +} + +static const struct udevice_id turris_omnia_mcu_ids[] = { + { .compatible ="cznic,turris-omnia-mcu" }, + { }
drivers/gpio/turris_omnia_mcu.c line 309
Quoted 10 lines
drivers/gpio/turris_omnia_mcu.c new file +10
-0+}; + +U_BOOT_DRIVER (turris_omnia_mcu) = { + .name ="turris-omnia-mcu" , + .id =UCLASS_GPIO , + .ops = &turris_omnia_mcu_ops, + .probe = turris_omnia_mcu_probe, + .plat_auto =sizeof (struct turris_omnia_mcu_info ), + .of_match = turris_omnia_mcu_ids, +};
Viele Grüße,
Stefan Roese
Signature · 3 lines
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: (+49)-8142-66989-51 Fax: (+49)-8142-66989-80 Email: [email protected]