Can't get headset to pair
Trying to get a bluetooth headset (http://www.ebuyer.com/product/123000) to work with bluez, so that I can access it from alsa. Running Debian lenny (2.6.22 kernel), bluez 3.24.
With the headset in pairing mode:
laptop:~# hcitool scan Scanning ... 00:02:5B:02:64:9D VBH-006 laptop:~# hcitool cc 00:02:5B:02:64:9D laptop:~#
System log reports:
Mar 6 00:44:19 laptop NetworkManager: <debug> [1204764259.628237] nm_hal_device_added(): New device added (hal udi is '/org/freedesktop/Hal/devices/bluetooth_acl_25b02649d'). Mar 6 00:44:22 laptop NetworkManager: <debug> [1204764262.493448]
nm_hal_device_removed(): Device removed (hal udi is '/org/freedesktop/Hal/devices/bluetooth_acl_25b02649d').
The light on the hands-free doesn't start to flash, indicating that pairing didn't take place. My /etc/bluetooth/hcid.conf contains:pin_helper /etc/bluetooth/feed-pin.sh;
and /etc/bluetooth/feed-pin.sh contains:
#!/bin/sh
echo "PIN:0000"
which runs fine as a shell script.
My normal user .asoundrc contains:
pcm.bluetooth {
type bluetooth
device 00:02:5B:02:64:9D
}
Have I missed something? Do I need to pair the device before it will work?
TD
-------------------------------------------------------------------------
This SF.net email is sponsored by: Microsoft Defy all challenges. Microsoft(R) Visual Studio 2008.
http://clk.atdmt.com/MRT/go/vse0120000070mrt/direct/01/
_______________________________________________
Bluez-users mailing list [email protected]
https://lists.sourceforge.net/lists/listinfo/bluez-users
The only way I could find to initiate pairing with my headphones was by following the instructions in http://wiki.bluez.org/wiki/HOWTO/Bonding in the "dbus-send" section.
I'd be interested in hearing if there's another way (that doesn't involve writing a program).
Also, make sure that there's a passkey/auth agent running (such as bluetooth-applet of bluez-gnome)
-------------------------------------------------------------------------
This SF.net email is sponsored by: Microsoft Defy all challenges. Microsoft(R) Visual Studio 2008.
http://clk.atdmt.com/MRT/go/vse0120000070mrt/direct/01/
_______________________________________________
Bluez-users mailing list [email protected]
https://lists.sourceforge.net/lists/listinfo/bluez-users
[Bluez-users] How to change the Hci packet size?
In reply to TDHi, what it the largest packet size for the Hci?
Is it a configuration in the BlueZ or is it a configuration in the adapter? thanks
-------------------------------------------------------------------------
This SF.net email is sponsored by: Microsoft Defy all challenges. Microsoft(R) Visual Studio 2008.
http://clk.atdmt.com/MRT/go/vse0120000070mrt/direct/01/
_______________________________________________
Bluez-users mailing list [email protected]
https://lists.sourceforge.net/lists/listinfo/bluez-users
Marcel Holtmann
maintainerRe: [Bluez-users] How to change the Hci packet size?
Hi,
Quoted 3 lines
Hi, what it the largest packet size for the Hci?
Is it a configuration in the BlueZ or is it a configuration in the adapter?
don't bother in trying. The firmware inside the Bluetooth chip is responsible for doing this job. It will pick the packet type that is best suitable.
Regards
Marcel
-------------------------------------------------------------------------
This SF.net email is sponsored by: Microsoft Defy all challenges. Microsoft(R) Visual Studio 2008.
http://clk.atdmt.com/MRT/go/vse0120000070mrt/direct/01/
_______________________________________________
Bluez-users mailing list [email protected]
https://lists.sourceforge.net/lists/listinfo/bluez-users
Re: [Bluez-users] How to change the Hci packet size?
Thanks.. but I remember something in the Bluetooth standard like 'continue' flag in each HCI packet.. Who is responsible to fill this? Thanks again marcel..
--------------------------------------------------
From: "Marcel Holtmann" <[email protected]>
Sent: Thursday, March 06, 2008 5:53 PM
To: "BlueZ users" <[email protected]>
Subject: Re: [Bluez-users] How to change the Hci packet size?
Quoted 15 lines
Hi,
Quoted 3 lines
Hi, what it the largest packet size for the Hci?
Is it a configuration in the BlueZ or is it a configuration in the adapter?don't bother in trying. The firmware inside the Bluetooth chip is responsible for doing this job. It will pick the packet type that is best suitable.
Regards
Marcel
Quoted 8 lines
-------------------------------------------------------------------------
This SF.net email is sponsored by: Microsoft Defy all challenges. Microsoft(R) Visual Studio 2008.
http://clk.atdmt.com/MRT/go/vse0120000070mrt/direct/01/
_______________________________________________
Bluez-users mailing list [email protected]
https://lists.sourceforge.net/lists/listinfo/bluez-users
-------------------------------------------------------------------------
This SF.net email is sponsored by: Microsoft Defy all challenges. Microsoft(R) Visual Studio 2008.
http://clk.atdmt.com/MRT/go/vse0120000070mrt/direct/01/
_______________________________________________
Bluez-users mailing list [email protected]
https://lists.sourceforge.net/lists/listinfo/bluez-users
Marcel Holtmann
maintainerRe: [Bluez-users] How to change the Hci packet size?
Hi,
Quoted 3 lines
Thanks.. but I remember something in the Bluetooth standard like 'continue'
flag in each HCI packet.. Who is responsible to fill this?
the L2CAP layer will fill this in.
Regards
Marcel
-------------------------------------------------------------------------
This SF.net email is sponsored by: Microsoft Defy all challenges. Microsoft(R) Visual Studio 2008.
http://clk.atdmt.com/MRT/go/vse0120000070mrt/direct/01/
_______________________________________________
Bluez-users mailing list [email protected]
https://lists.sourceforge.net/lists/listinfo/bluez-users