No TV after an dist-upgrade

Quoted 1 line

Quoted 1 line

tune to:

Quoted 1 line

Quoted 1 line

tune to:

Quoted 1 line

Quoted 1 line

tune to:

Quoted 1 line

Quoted 1 line

tune to:

Quoted 1 line

Quoted 1 line

tune to:

Hi,

There is still one week, I was watching TV (DVB-T) on my PC with Kaffeine without problems. My PC uses a Debian Etch, last weekend I do an update to Etch (final), then Lenny, since everything works except the TV. Strange !?

I use a DVB-T card ASUSTeK P7131 Dual, and I use a custom Linux kernel 2.6.24 with DVB support. I kept the same kernel (2.6.24) before and after the upgrade.

- The card is well recognized by the kernel, dmesg output:

saa7133[0]: found at 0000:05:03.0, rev: 209, irq: 16, latency: 64, mmio:
0xff7ff000
saa7133[0]: subsystem: 1043:4876, board: ASUSTeK P7131 Hybrid [card=112,autodetected]
saa7133[0]: board init: gpio is 0
input: saa7134 IR (ASUSTeK P7131 Hybri as /class/input/input4 saa7133[0]: i2c eeprom 00: 43 10 76 48 54 20 1c 00 43 43 a9 1c 55 d2 b2 92 saa7133[0]: i2c eeprom 10: ff ff ff 0f ff 20 ff ff ff ff ff ff ff ff ff ff saa7133[0]: i2c eeprom 20: 01 40 01 02 03 01 01 03 08 ff 00 d5 ff ff ff ff saa7133[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7133[0]: i2c eeprom 40: ff 21 00 c2 96 10 03 32 55 50 ff ff ff ff ff ff saa7133[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7133[0]: i2c eeprom 60: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7133[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff tuner 1-004b: chip found @ 0x96 (saa7133[0])
tda8290 1-004b: setting tuner address to 61
tuner 1-004b: type set to tda8290+75a
tda8290 1-004b: setting tuner address to 61
tuner 1-004b: type set to tda8290+75a
saa7133[0]: registered device video0 [v4l2]
saa7133[0]: registered device vbi0
saa7133[0]: registered device radio0
DVB: registering new adapter (saa7133[0])
DVB: registering frontend 0 (Philips TDA10046H DVB-T)...
tda1004x: setting up plls for 48MHz sampling clock
tda1004x: timeout waiting for DSP ready
tda1004x: found firmware revision 0 -- invalid
tda1004x: trying to boot from eeprom
tda1004x: timeout waiting for DSP ready
tda1004x: found firmware revision 0 -- invalid
tda1004x: waiting for firmware upload...
tda1004x: found firmware revision 29 -- ok
saa7134 ALSA driver for DMA sound loaded
saa7133[0]/alsa: saa7133[0] at 0xff7ff000 irq 16 registered as card -1

- Devices :

$ ls -l /dev/dvb/adapter0/
crw-rw---- 1 root video 212, 4 avr 11 19:55 demux0
crw-rw---- 1 root video 212, 5 avr 11 19:55 dvr0
crw-rw---- 1 root video 212, 3 avr 11 19:55 frontend0
crw-rw---- 1 root video 212, 7 avr 11 19:55 net0

- I use the file fr-Vannes, when I scan, I have these messages :

$ sudo scan /usr/share/doc/dvb-utils/examples/scan/dvb-t/fr-Vannes
scanning /usr/share/doc/dvb-utils/examples/scan/dvb-t/fr-Vannes
using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0'
initial transponder 674167000 0 2 9 3 1 0 0
initial transponder 698167000 0 2 9 3 1 0 0
initial transponder 762167000 0 2 9 3 1 0 0
initial transponder 778167000 0 2 9 3 1 0 0
initial transponder 818167000 0 2 9 3 1 0 0

Quoted 1 line

Quoted 1 line

Quoted 1 line

tune to:

674167000:INVERSION_AUTO:BANDWIDTH_8_MHZ:FEC_2_3:FEC_AUTO:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_32:HIERARCHY_NONE
WARNING: filter timeout pid 0x0502
WARNING: filter timeout pid 0x0504
WARNING: filter timeout pid 0x050a
WARNING: filter timeout pid 0x0500
WARNING: filter timeout pid 0x0011
WARNING: filter timeout pid 0x0503
WARNING: filter timeout pid 0x0506
WARNING: filter timeout pid 0x0505
WARNING: filter timeout pid 0x0010

Quoted 1 line

Quoted 1 line

Quoted 1 line

tune to:

698167000:INVERSION_AUTO:BANDWIDTH_8_MHZ:FEC_2_3:FEC_AUTO:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_32:HIERARCHY_NONE
WARNING: filter timeout pid 0x0011
WARNING: filter timeout pid 0x0000
WARNING: filter timeout pid 0x0010

Quoted 1 line

Quoted 1 line

Quoted 1 line

tune to:

762167000:INVERSION_AUTO:BANDWIDTH_8_MHZ:FEC_2_3:FEC_AUTO:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_32:HIERARCHY_NONE
WARNING: filter timeout pid 0x0011
WARNING: filter timeout pid 0x0000
WARNING: filter timeout pid 0x0010

Quoted 1 line

Quoted 1 line

Quoted 1 line

tune to:

778167000:INVERSION_AUTO:BANDWIDTH_8_MHZ:FEC_2_3:FEC_AUTO:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_32:HIERARCHY_NONE
WARNING: filter timeout pid 0x0011
WARNING: filter timeout pid 0x0000
WARNING: filter timeout pid 0x0010

Quoted 1 line

Quoted 1 line

Quoted 1 line

tune to:

818167000:INVERSION_AUTO:BANDWIDTH_8_MHZ:FEC_2_3:FEC_AUTO:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_32:HIERARCHY_NONE
WARNING: filter timeout pid 0x0011
WARNING: filter timeout pid 0x0000
WARNING: filter timeout pid 0x0010
dumping lists (7 services) [0201]:674167000:INVERSION_AUTO:BANDWIDTH_8_MHZ:FEC_2_3:FEC_AUTO:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_32:HIERARCHY_NONE:0:0:513 [0207]:674167000:INVERSION_AUTO:BANDWIDTH_8_MHZ:FEC_2_3:FEC_AUTO:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_32:HIERARCHY_NONE:0:0:519 [02ff]:674167000:INVERSION_AUTO:BANDWIDTH_8_MHZ:FEC_2_3:FEC_AUTO:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_32:HIERARCHY_NONE:0:0:767 [0206]:674167000:INVERSION_AUTO:BANDWIDTH_8_MHZ:FEC_2_3:FEC_AUTO:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_32:HIERARCHY_NONE:0:0:518 [0205]:674167000:INVERSION_AUTO:BANDWIDTH_8_MHZ:FEC_2_3:FEC_AUTO:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_32:HIERARCHY_NONE:0:0:517 [0204]:674167000:INVERSION_AUTO:BANDWIDTH_8_MHZ:FEC_2_3:FEC_AUTO:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_32:HIERARCHY_NONE:0:0:516 [0203]:674167000:INVERSION_AUTO:BANDWIDTH_8_MHZ:FEC_2_3:FEC_AUTO:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_32:HIERARCHY_NONE:0:0:515 Done.

I have no error messages in the log, it's one week that I seek, I do not understand what is no longer working.

Hi,

You do not see where the problem is coming?

On the same weekend that the upgrade, I have new neighbors who are installed, it may be an antenna problem?