make gnutv more resilient to temporary slow reads.

I have been using gnutv to save data to my network drive.
Event if the average speed required to save is way less than the bandwidth, gnutv sometimes does not read fast enough to avoid overflow of the dvb ring buffer.

In that case gnutv prints an error message and stops recording.

In my opinion, it would be better to bite the bullet, loose a bit of the stream, and carry on, in the hope that the system will not be too busy.

Here is the patch

diff -r 73b910014d07 util/gnutv/gnutv_data.c
@@ -222,19 +238,26 @@
         while(!outputthread_shutdown) {
                 if (poll(&pollfd, 1, 1000) != 1)
                         continue;
+
+               // in case of read error, we should not abort in order to minimize the loss of data.
+
                 if (pollfd.revents & POLLERR) {
                         if (errno == EINTR)
                                 continue;
-                       fprintf(stderr, "DVR device read failure\n");
-                       return 0;
+                       fprintf(stderr, "DVR device poll failure\n");
+
+                       // This is tipically EOVERFLOW, i.e. dvb internal buffer run out of space
+
+                       // The next read will fail too, but it will also clear the error flag in the

driver
+ // so that following reads will succeed

                 }

                 int size = read(dvrfd, buf, sizeof(buf));
                 if (size < 0) {
                         if (errno == EINTR)
                                 continue;
-                       fprintf(stderr, "DVR device read failure\n");
-                       return 0;
+                       fprintf(stderr, "DVR device read failure. Possible loss of data.\n");
+                       // The error flag has been cleared, next read should succeed.
                 }

                 written = 0;
@@ -243,6 +266,7 @@
                         if (tmp == -1) {
                                 if (errno != EINTR) {
                                         fprintf(stderr, "Write error: %m\n");
+                                       // abort loop
                                         break;
                                 }
                         } else {

diff -r 73b910014d07 util/gnutv/gnutv_data.c
@@ -222,19 +238,26 @@
 	while(!outputthread_shutdown) {
 		if (poll(&pollfd, 1, 1000) != 1)
 			continue;
+
+		// in case of read error, we should not abort in order to minimize the loss of data.
+
 		if (pollfd.revents & POLLERR) {
 			if (errno == EINTR)
 				continue;
-			fprintf(stderr, "DVR device read failure\n");
-			return 0;
+			fprintf(stderr, "DVR device poll failure\n");
+
+			// This is tipically EOVERFLOW, i.e. dvb internal buffer run out of space
+
+			// The next read will fail too, but it will also clear the error flag in the driver
+			// so that following reads will succeed
 		}
 
 		int size = read(dvrfd, buf, sizeof(buf));
 		if (size < 0) {
 			if (errno == EINTR)
 				continue;
-			fprintf(stderr, "DVR device read failure\n");
-			return 0;
+			fprintf(stderr, "DVR device read failure. Possible loss of data.\n");
+			// The error flag has been cleared, next read should succeed.
 		}
 
 		written = 0;

@@ -243,6 +266,7 @@
 			if (tmp == -1) {
 				if (errno != EINTR) {
 					fprintf(stderr, "Write error: %m\n");
+					// abort loop
 					break;
 				}
 			} else {

_______________________________________________
linux-dvb mailing list
[email protected]
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb