Skip to contentSkip to conversation

Do not get BCM4303 to work

DISCUSSION feldmaus 3 participants 15 messages Sep 8, 2008 – Jan 4, 2009

lore
Share & tools
lore

feldmaus

author
#0 lore raw

Hi All,

i do not get my Wlan Card with BCM4303 Chip to work.

My System is Debian Testing 32-bit with Kernel 2.6.25-2 from Debian, therefore i am using the Driver b43legacy.

I tried to connect this Wlan Card with my Wireless Printer. It is a Ad-Hoc Connection with,
SSID=3Dkleopatra
Channel=3D10
Authentification=3Dnon
Encryption=3D128-bit Wep

Here it comes the Outout from <lspci>,
02:02.0 Network controller: Broadcom Corporation BCM4303 802.11b Wireless LAN Controller (rev 02)
Subsystem: Hewlett-Packard Company Device 12f3
Flags: bus master, fast devsel, latency 64, IRQ 17 Memory at e0104000 (32-bit, non-prefetchable) [size=3D8K] Kernel driver in use: b43-pci-bridge
Kernel modules: ssb

I tried some Howtos, but it didn't work.

<ifconfig> show's the following,
eth0 Link encap:Ethernet Hardware Adresse 00:0f:b0:0e:57:a1

          inet Adresse:77.21.170.83  Bcast:255.255.255.255
Maske:255.255.252.0
          UP BROADCAST RUNNING MULTICAST  MTU:576  Metrik:1
          RX packets:35420 errors:0 dropped:0 overruns:0 frame:0
          TX packets:1946 errors:0 dropped:0 overruns:0 carrier:0
          Kollisionen:0 Sendewarteschlangenl=E4nge:1000
          RX bytes:3756084 (3.5 MiB)  TX bytes:245214 (239.4 KiB)
          Interrupt:18 Basisadresse:0x7000

lo Link encap:Lokale Schleife
inet Adresse:127.0.0.1 Maske:255.0.0.0
inet6-Adresse: ::1/128 G=FCltigkeitsbereich:Maschine UP LOOPBACK RUNNING MTU:16436 Metrik:1
RX packets:10 errors:0 dropped:0 overruns:0 frame:0 TX packets:10 errors:0 dropped:0 overruns:0 carrier:0 Kollisionen:0 Sendewarteschlangenl=E4nge:0 RX bytes:660 (660.0 B) TX bytes:660 (660.0 B)

wlan0 Link encap:Ethernet Hardware Adresse 00:90:4b:97:34:73
UP BROADCAST MULTICAST MTU:1500 Metrik:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 Kollisionen:0 Sendewarteschlangenl=E4nge:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)

wmaster0 Link encap:UNSPEC Hardware Adresse 00-90-4B-97-34-73-6C-6F-00-00-00-00-00-00-00-00
UP BROADCAST RUNNING MULTICAST MTU:1500 Metrik:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 Kollisionen:0 Sendewarteschlangenl=E4nge:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)

<iwconfig> shows this,
lo no wireless extensions.

eth0 no wireless extensions.

wmaster0 no wireless extensions.

wlan0 IEEE 802.11b ESSID:""
Mode:Managed Frequency:2.412 GHz Access Point:
Not-Associated
Tx-Power=3D27 dBm
Retry min limit:7 RTS thr:off Fragment thr=3D2352 B
Encryption key:off
Link Quality:0 Signal level:0 Noise level:0 Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0

I am not sure whether this Card is active, because <dmesg> show me,

[  409.752921] b43legacy-phy0: Radio hardware status changed to DISABLE=

D

Another funny Thing is, that i can execute <iwlist wla0 scanning> and=20 get a Result,
wlan0 Scan completed :

          Cell 01 - Address: 02:00:7C:81:E1:73
                    ESSID:"kleopatra"
                    Mode:Ad-Hoc
                    Channel:10
                    Frequency:2.457 GHz (Channel 10)
                    Quality=3D55/100  Signal level=3D-55 dBm  Noise=20
level=3D-43 dBm
                    Encryption key:on
                    Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s
                    Extra:tsf=3D0000000075bb2b8d

The Adress seems to change sometimes ??? I don't know why.

Regards Markus

--
To unsubscribe from this list: send the line "unsubscribe linux-wireles= s" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html

#1 lore raw
Quoted 7 lines · feldmaus

Hi All,

i do not get my Wlan Card with BCM4303 Chip to work.

My System is Debian Testing 32-bit with Kernel 2.6.25-2 from Debian, therefore i am using the Driver b43legacy.

out of date, Debian Lenny has 2.6.26

#2 lore raw
In reply to feldmaus
Quoted 6 lines · feldmaus

Hi All,

i do not get my Wlan Card with BCM4303 Chip to work.

I am not sure whether this Card is active, because <dmesg> show me,

[  409.752921] b43legacy-phy0: Radio hardware status changed to DISABLED

Your card can receive, but not transmit due to a problem with the rfkill switch handling in b43legacy. I'm working on this problem with a Ubuntu user, and will post patches as soon as the problem is fixed.

Larry

author
#3 lore raw
Quoted 11 lines · Larry Finger
Quoted 6 lines · feldmaus

Hi All,

i do not get my Wlan Card with BCM4303 Chip to work.

I am not sure whether this Card is active, because <dmesg> show me,

[  409.752921] b43legacy-phy0: Radio hardware status changed to DISABLED

Your card can receive, but not transmit due to a problem with the rfkill switch handling in b43legacy. I'm working on this problem with a Ubuntu user, and will post patches as soon as the problem is fixed.

Larry

Thanks for your Support.

I installed the Kernel 2.6.26-1 as Maximilian said. I hope i can try to get my Card to work.
If you need some Messages then let me know.

Regards Markus

#4 lore raw
Quoted 9 lines · feldmaus
Quoted 3 lines · Larry Finger

Your card can receive, but not transmit due to a problem with the rfkill switch handling in b43legacy. I'm working on this problem with a Ubuntu user, and will post patches as soon as the problem is fixed.

Larry

Thanks for your Support.

I installed the Kernel 2.6.26-1 as Maximilian said. I hope i can try to get my Card to work.
If you need some Messages then let me know.

The Ubuntu user and I have discovered that his computer needs the hp-dmi module that is part of the mainline kernel since 2.6.27-rc6. This module handles the rfkill button that does not produce a scancode. I think you will need to get that one for you to be able to turn the radio on.

Larry

author
#5 lore raw
Quoted 4 lines · Larry Finger
Quoted 3 lines · feldmaus
Quoted 2 lines · Larry Finger

Your card can receive, but not transmit due to a problem with the rfkill switch handling in b43legacy. I'm working on this problem with a Ubuntu user, and will post patches as soon as the problem is fixed.

Quoted 8 lines
Quoted 6 lines
Quoted 1 line

Larry

Thanks for your Support.

I installed the Kernel 2.6.26-1 as Maximilian said. I hope i can try to get my Card to work.
If you need some Messages then let me know.

The Ubuntu user and I have discovered that his computer needs the hp-dmi module that is part of the mainline kernel since 2.6.27-rc6. This module handles the rfkill button that does not produce a scancode. I think you will need to get that one for you to be able to turn the radio on.

So the hp-dmi Module is only available in 2.6.27 ?

Regards feldmaus

#6 lore raw
Quoted 1 line · feldmaus

So the hp-dmi Module is only available in 2.6.27 ?

Yes.

author
#7 lore raw
In reply to Larry Finger
Quoted 7 lines · Larry Finger
Quoted 6 lines · feldmaus

Hi All,

i do not get my Wlan Card with BCM4303 Chip to work.

I am not sure whether this Card is active, because <dmesg> show me,

[  409.752921] b43legacy-phy0: Radio hardware status changed to DISA=

BLED

Quoted 2 lines

=20
Your card can receive, but not transmit due to a problem with the rfk=

ill=20

Quoted 1 line

switch handling in b43legacy. I'm working on this problem with a Ubun=

tu=20

Quoted 3 lines

user, and will post patches as soon as the problem is fixed. =20
Larry

Hi Larry,

i thought it would be helpful to post my Messages. :-) If not ignore this Message.:-)

I am using the NetworkManager Applet to show and connect to Wlan Networ= ks.
My wireless Button shines blue when my Linux System starts. However after i login onto myGnome Desktop and after some time the=20 NetworkManager Applet shows me my Wireless Network.

dmesg says,
=2E..

[   22.024553] Broadcom 43xx-legacy driver loaded [ Features: PLRID,=20
=46irmware-ID: FW10 ]
=2E..
[   43.384052] b43legacy-phy0: Loading firmware version 0x127, patch
level 14 (2005-04-18 02:36:27)
[   40.776050] b43legacy-phy0: Loading firmware version 0x127, patch=20
level 14 (2005-04-18 02:36:27)
[   40.892896] b43legacy-phy0 debug: Chip initialized
[   40.893291] b43legacy-phy0 debug: 30-bit DMA initialized
[   40.893422] Registered led device: b43legacy-phy0:tx
[   40.901752] Registered led device: b43legacy-phy0:rx
[   40.909982] Registered led device: b43legacy-phy0:radio
[   40.918152] b43legacy-phy0 debug: Wireless interface started
[   40.918159] b43legacy-phy0 debug: Adding Interface type 2
[   40.936417] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   41.300046] b43legacy-phy0: Radio hardware status changed to DISABLE=

D
=2E..

Then i try to connect to this Network by press on my listed Network in the NetworkManager Applet. Then he connects to the Network. Der Network= =20
Balken zeigt einen Verbindungsstatus an von 0%.

dmesg says,

[  530.437247] b43legacy-phy0 debug: Removing Interface type 2
[  530.446006] b43legacy-phy0 debug: Wireless interface stopped
[  530.446142] b43legacy-phy0 debug: DMA-30 0x0260 (RX) max used slots:=
1/64
[  530.446190] b43legacy-phy0 debug: DMA-30 0x0200 (RX) max used slots:=
1/64
[  530.446245] b43legacy-phy0 debug: DMA-30 0x02A0 (TX) max used slots:=
=20
0/128
[  530.452052] b43legacy-phy0 debug: DMA-30 0x0280 (TX) max used slots:=
=20
0/128
[  530.460038] b43legacy-phy0 debug: DMA-30 0x0260 (TX) max used slots:=
=20
0/128
[  530.468036] b43legacy-phy0 debug: DMA-30 0x0240 (TX) max used slots:=
=20
0/128
[  530.476042] b43legacy-phy0 debug: DMA-30 0x0220 (TX) max used slots:=
=20
2/128
[  530.485144] b43legacy-phy0 debug: DMA-30 0x0200 (TX) max used slots:=
=20
0/128
[  530.492042] b43legacy-phy0 debug: Radio initialized
[  530.492058] b43legacy-phy0 debug: Radio initialized
[  530.506575] input: b43legacy-phy0 as /class/input/input10
[  530.672048] b43legacy-phy0: Loading firmware version 0x127, patch=20
level 14 (2005-04-18 02:36:27)
[  530.824472] b43legacy-phy0 debug: Chip initialized
[  530.824862] b43legacy-phy0 debug: 30-bit DMA initialized
[  530.824993] Registered led device: b43legacy-phy0:tx
[  530.825031] Registered led device: b43legacy-phy0:rx
[  530.825069] Registered led device: b43legacy-phy0:radio
[  530.825102] b43legacy-phy0 debug: Wireless interface started
[  530.825109] b43legacy-phy0 debug: Adding Interface type 3
[  530.846071] wlan0: Trigger new scan to find an IBSS to join
[  531.520050] b43legacy-phy0: Radio hardware status changed to DISABLE=
D
[  531.520431] b43legacy-phy0 debug: Radio initialized
[  531.584041] b43legacy-phy0: Radio turned on by software
[  531.584055] b43legacy-phy0: The hardware RF-kill button still turns=20
the radio physically off. Press the button to turn it on.
[  533.652045] wlan0: Trigger new scan to find an IBSS to join
[  536.428046] wlan0: Trigger new scan to find an IBSS to join
[  539.204045] wlan0: Trigger new scan to find an IBSS to join
[  539.980089] wlan0: Creating new IBSS network, BSSID 96:d6:b6:75:12:4=
a
[  539.980130] wlan0: Configured IBSS beacon template
[  540.928032] wlan0: no IPv6 routers present
[  569.980046] wlan0: No active IBSS STAs - trying to scan for other=20
IBSS networks with same SSID (merge)
[  600.756051] wlan0: No active IBSS STAs - trying to scan for other=20
IBSS networks with same SSID (merge)
[  612.720029] wlan0: no IPv6 routers present
[  725.457997] wlan0: deauthenticate(reason=3D3)
[  726.477007] b43legacy-phy0 debug: Removing Interface type 3
[  726.492057] b43legacy-phy0 debug: Wireless interface stopped
[  726.492226] b43legacy-phy0 debug: DMA-30 0x0260 (RX) max used slots:=
1/64
[  726.492272] b43legacy-phy0 debug: DMA-30 0x0200 (RX) max used slots:=
1/64
[  726.492329] b43legacy-phy0 debug: DMA-30 0x02A0 (TX) max used slots:=
=20
0/128
[  726.500165] b43legacy-phy0 debug: DMA-30 0x0280 (TX) max used slots:=
=20
0/128
[  726.508046] b43legacy-phy0 debug: DMA-30 0x0260 (TX) max used slots:=
=20
0/128
[  726.516038] b43legacy-phy0 debug: DMA-30 0x0240 (TX) max used slots:=
=20
0/128
[  726.524214] b43legacy-phy0 debug: DMA-30 0x0220 (TX) max used slots:=
=20
4/128
[  726.532042] b43legacy-phy0 debug: DMA-30 0x0200 (TX) max used slots:=
=20
0/128
[  726.540054] b43legacy-phy0 debug: Radio initialized
[  726.540069] b43legacy-phy0 debug: Radio initialized
[  726.633096] input: b43legacy-phy0 as /class/input/input11
[  726.796037] b43legacy-phy0: Loading firmware version 0x127, patch=20
level 14 (2005-04-18 02:36:27)
[  726.896786] b43legacy-phy0 debug: Chip initialized
[  726.897036] b43legacy-phy0 debug: 30-bit DMA initialized
[  726.897117] Registered led device: b43legacy-phy0:tx
[  726.897133] Registered led device: b43legacy-phy0:rx
[  726.897149] Registered led device: b43legacy-phy0:radio
[  726.897172] b43legacy-phy0 debug: Wireless interface started
[  726.897175] b43legacy-phy0 debug: Adding Interface type 3
[  727.644031] b43legacy-phy0: Radio hardware status changed to DISABLE=
D
[  727.924601] b43legacy-phy0 debug: Removing Interface type 3
[  727.930047] b43legacy-phy0 debug: Wireless interface stopped
[  727.930129] b43legacy-phy0 debug: DMA-30 0x0260 (RX) max used slots:=
1/64
[  727.930159] b43legacy-phy0 debug: DMA-30 0x0200 (RX) max used slots:=
0/64
[  727.930203] b43legacy-phy0 debug: DMA-30 0x02A0 (TX) max used slots:=
=20
0/128
[  727.936037] b43legacy-phy0 debug: DMA-30 0x0280 (TX) max used slots:=
=20
0/128
[  727.944029] b43legacy-phy0 debug: DMA-30 0x0260 (TX) max used slots:=
=20
0/128
[  727.952032] b43legacy-phy0 debug: DMA-30 0x0240 (TX) max used slots:=
=20
0/128
[  727.960033] b43legacy-phy0 debug: DMA-30 0x0220 (TX) max used slots:=
=20
2/128
[  727.968034] b43legacy-phy0 debug: DMA-30 0x0200 (TX) max used slots:=
=20
0/128
[  727.976034] b43legacy-phy0 debug: Radio initialized
[  727.976043] b43legacy-phy0 debug: Radio initialized
[  727.983509] input: b43legacy-phy0 as /class/input/input12
[  728.152040] b43legacy-phy0: Loading firmware version 0x127, patch=20
level 14 (2005-04-18 02:36:27)
[  728.252442] b43legacy-phy0 debug: Chip initialized
[  728.252729] b43legacy-phy0 debug: 30-bit DMA initialized
[  728.252819] Registered led device: b43legacy-phy0:tx
[  728.252839] Registered led device: b43legacy-phy0:rx
[  728.252858] Registered led device: b43legacy-phy0:radio
[  728.252883] b43legacy-phy0 debug: Wireless interface started
[  728.252887] b43legacy-phy0 debug: Adding Interface type 2
[  728.280215] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[  728.344731] b43legacy-phy0 debug: Removing Interface type 2
[  728.349895] b43legacy-phy0 debug: Wireless interface stopped
[  728.349978] b43legacy-phy0 debug: DMA-30 0x0260 (RX) max used slots:=
0/64
[  728.350008] b43legacy-phy0 debug: DMA-30 0x0200 (RX) max used slots:=
0/64
[  728.350046] b43legacy-phy0 debug: DMA-30 0x02A0 (TX) max used slots:=
=20
0/128
[  728.356050] b43legacy-phy0 debug: DMA-30 0x0280 (TX) max used slots:=
=20
0/128
[  728.364030] b43legacy-phy0 debug: DMA-30 0x0260 (TX) max used slots:=
=20
0/128
[  728.372028] b43legacy-phy0 debug: DMA-30 0x0240 (TX) max used slots:=
=20
0/128
[  728.380028] b43legacy-phy0 debug: DMA-30 0x0220 (TX) max used slots:=
=20
0/128
[  728.388030] b43legacy-phy0 debug: DMA-30 0x0200 (TX) max used slots:=
=20
0/128
[  728.396033] b43legacy-phy0 debug: Radio initialized
[  728.396042] b43legacy-phy0 debug: Radio initialized
[  728.403446] input: b43legacy-phy0 as /class/input/input13
[  728.572043] b43legacy-phy0: Loading firmware version 0x127, patch=20
level 14 (2005-04-18 02:36:27)
[  728.672542] b43legacy-phy0 debug: Chip initialized
[  728.672827] b43legacy-phy0 debug: 30-bit DMA initialized
[  728.672916] Registered led device: b43legacy-phy0:tx
[  728.672937] Registered led device: b43legacy-phy0:rx
[  728.672956] Registered led device: b43legacy-phy0:radio
[  728.672981] b43legacy-phy0 debug: Wireless interface started
[  728.672985] b43legacy-phy0 debug: Adding Interface type 3
[  728.693355] wlan0: Trigger new scan to find an IBSS to join
[  729.416034] b43legacy-phy0: Radio hardware status changed to DISABLE=
D
[  729.416179] b43legacy-phy0 debug: Radio initialized
[  729.500029] b43legacy-phy0: Radio turned on by software
[  729.500037] b43legacy-phy0: The hardware RF-kill button still turns=20
the radio physically off. Press the button to turn it on.
[  731.500116] wlan0: Trigger new scan to find an IBSS to join
[  734.276046] wlan0: Trigger new scan to find an IBSS to join
[  737.052043] wlan0: Trigger new scan to find an IBSS to join
[  737.828087] wlan0: Creating new IBSS network, BSSID f2:00:ad:b6:b3:3=
a
[  737.828128] wlan0: Configured IBSS beacon template
[  738.884029] wlan0: no IPv6 routers present
[  767.828045] wlan0: No active IBSS STAs - trying to scan for other=20
IBSS networks with same SSID (merge)
[  798.604045] wlan0: No active IBSS STAs - trying to scan for other=20
IBSS networks with same SSID (merge)
[  810.584030] wlan0: no IPv6 routers present
[  994.892048] wlan0: No active IBSS STAs - trying to scan for other=20
IBSS networks with same SSID (merge)
[ 1025.668044] wlan0: No active IBSS STAs - trying to scan for other=20

IBSS networks with same SSID (merge)

ifconfig says,
wlan0 Link encap:Ethernet Hardware Adresse 00:90:4b:97:34:73

          inet Adresse:169.254.78.197  Bcast:169.254.255.255=20
Maske:255.255.0.0
          inet6-Adresse: fe80::290:4bff:fe97:3473/64=20

G=FCltigkeitsbereich:Verbindung
UP BROADCAST RUNNING MULTICAST MTU:1500 Metrik:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:179 errors:0 dropped:0 overruns:0 carrier:0 Kollisionen:0 Sendewarteschlangenl=E4nge:1000 RX bytes:0 (0.0 B) TX bytes:32937 (32.1 KiB)

As you can see, some Packets would transmitted over my Wireless Card.

iwconfig says,
wlan0 IEEE 802.11 ESSID:"kleopatra"
Mode:Ad-Hoc Frequency:2.412 GHz Cell: 76:0D:1D:B5:B7:73 Tx-Power=3D27 dBm
Retry min limit:7 RTS thr:off Fragment thr=3D2352 B
Encryption key:off
Link Quality:0 Signal level:0 Noise level:0 Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0

However i can not print to my Wlan Printer and the status in the Networ= k=20
Manager shows 0%.

Then i pressed my wireless Button, and dmesg says

[ 1056.444034] wlan0: No active IBSS STAs - trying to scan for other=20
IBSS networks with same SSID (merge)
[ 1111.004046] wlan0: No active IBSS STAs - trying to scan for other=20
IBSS networks with same SSID (merge)
[ 1141.780078] wlan0: No active IBSS STAs - trying to scan for other=20
IBSS networks with same SSID (merge)
[ 1172.555792] wlan0: No active IBSS STAs - trying to scan for other=20
IBSS networks with same SSID (merge)
[ 1193.449106] phy0: Adding new IBSS station 00:30:6e:d2:4a:99 (dev=3Dw=
lan0)
[ 1212.996048] wlan0: expiring inactive STA 00:30:6e:d2:4a:99
[ 1212.996285] wlan0: No active IBSS STAs - trying to scan for other=20
IBSS networks with same SSID (merge)
[ 1243.772044] wlan0: No active IBSS STAs - trying to scan for other=20
IBSS networks with same SSID (merge)
[ 1274.548043] wlan0: No active IBSS STAs - trying to scan for other=20
IBSS networks with same SSID (merge)
[ 1320.929652] wlan0: deauthenticate(reason=3D3)
[ 1321.952124] b43legacy-phy0 debug: Removing Interface type 3
[ 1321.964039] b43legacy-phy0 debug: Wireless interface stopped
[ 1321.964127] b43legacy-phy0 debug: DMA-30 0x0260 (RX) max used slots:=
1/64
[ 1321.964160] b43legacy-phy0 debug: DMA-30 0x0200 (RX) max used slots:=
1/64
[ 1321.964198] b43legacy-phy0 debug: DMA-30 0x02A0 (TX) max used slots:=
=20
0/128
[ 1321.972035] b43legacy-phy0 debug: DMA-30 0x0280 (TX) max used slots:=
=20
0/128
[ 1321.980027] b43legacy-phy0 debug: DMA-30 0x0260 (TX) max used slots:=
=20
0/128
[ 1321.988031] b43legacy-phy0 debug: DMA-30 0x0240 (TX) max used slots:=
=20
0/128
[ 1321.996030] b43legacy-phy0 debug: DMA-30 0x0220 (TX) max used slots:=
=20
4/128
[ 1322.004028] b43legacy-phy0 debug: DMA-30 0x0200 (TX) max used slots:=
=20
0/128
[ 1322.012026] b43legacy-phy0 debug: Radio initialized
[ 1322.012035] b43legacy-phy0 debug: Radio initialized
[ 1322.093411] input: b43legacy-phy0 as /class/input/input14
[ 1322.256079] b43legacy-phy0: Loading firmware version 0x127, patch=20
level 14 (2005-04-18 02:36:27)
[ 1322.356791] b43legacy-phy0 debug: Chip initialized
[ 1322.357047] b43legacy-phy0 debug: 30-bit DMA initialized
[ 1322.357127] Registered led device: b43legacy-phy0:tx
[ 1322.357144] Registered led device: b43legacy-phy0:rx
[ 1322.357160] Registered led device: b43legacy-phy0:radio
[ 1322.357184] b43legacy-phy0 debug: Wireless interface started
[ 1322.357188] b43legacy-phy0 debug: Adding Interface type 3
[ 1323.104036] b43legacy-phy0: Radio hardware status changed to DISABLE=
D
[ 1323.384592] b43legacy-phy0 debug: Removing Interface type 3
[ 1323.396041] b43legacy-phy0 debug: Wireless interface stopped
[ 1323.396150] b43legacy-phy0 debug: DMA-30 0x0260 (RX) max used slots:=
1/64
[ 1323.396183] b43legacy-phy0 debug: DMA-30 0x0200 (RX) max used slots:=
0/64
[ 1323.396226] b43legacy-phy0 debug: DMA-30 0x02A0 (TX) max used slots:=
=20
0/128
[ 1323.404039] b43legacy-phy0 debug: DMA-30 0x0280 (TX) max used slots:=
=20
0/128
[ 1323.412026] b43legacy-phy0 debug: DMA-30 0x0260 (TX) max used slots:=
=20
0/128
[ 1323.420026] b43legacy-phy0 debug: DMA-30 0x0240 (TX) max used slots:=
=20
0/128
[ 1323.428031] b43legacy-phy0 debug: DMA-30 0x0220 (TX) max used slots:=
=20
2/128
[ 1323.436034] b43legacy-phy0 debug: DMA-30 0x0200 (TX) max used slots:=
=20
0/128
[ 1323.444032] b43legacy-phy0 debug: Radio initialized
[ 1323.444041] b43legacy-phy0 debug: Radio initialized
[ 1323.454511] input: b43legacy-phy0 as /class/input/input15
[ 1323.620042] b43legacy-phy0: Loading firmware version 0x127, patch=20
level 14 (2005-04-18 02:36:27)
[ 1323.720624] b43legacy-phy0 debug: Chip initialized
[ 1323.720911] b43legacy-phy0 debug: 30-bit DMA initialized
[ 1323.721002] Registered led device: b43legacy-phy0:tx
[ 1323.721024] Registered led device: b43legacy-phy0:rx
[ 1323.721043] Registered led device: b43legacy-phy0:radio
[ 1323.721069] b43legacy-phy0 debug: Wireless interface started
[ 1323.721073] b43legacy-phy0 debug: Adding Interface type 2
[ 1323.748106] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 1323.811666] b43legacy-phy0 debug: Removing Interface type 2
[ 1323.817608] b43legacy-phy0 debug: Wireless interface stopped
[ 1323.817690] b43legacy-phy0 debug: DMA-30 0x0260 (RX) max used slots:=
0/64
[ 1323.817722] b43legacy-phy0 debug: DMA-30 0x0200 (RX) max used slots:=
0/64
[ 1323.817761] b43legacy-phy0 debug: DMA-30 0x02A0 (TX) max used slots:=
=20
0/128
[ 1323.824041] b43legacy-phy0 debug: DMA-30 0x0280 (TX) max used slots:=
=20
0/128
[ 1323.832037] b43legacy-phy0 debug: DMA-30 0x0260 (TX) max used slots:=
=20
0/128
[ 1323.840033] b43legacy-phy0 debug: DMA-30 0x0240 (TX) max used slots:=
=20
0/128
[ 1323.848029] b43legacy-phy0 debug: DMA-30 0x0220 (TX) max used slots:=
=20
0/128
[ 1323.856035] b43legacy-phy0 debug: DMA-30 0x0200 (TX) max used slots:=
=20
0/128
[ 1323.864839] b43legacy-phy0 debug: Radio initialized
[ 1323.864849] b43legacy-phy0 debug: Radio initialized
[ 1323.872375] input: b43legacy-phy0 as /class/input/input16
[ 1324.040043] b43legacy-phy0: Loading firmware version 0x127, patch=20
level 14 (2005-04-18 02:36:27)
[ 1324.140544] b43legacy-phy0 debug: Chip initialized
[ 1324.140835] b43legacy-phy0 debug: 30-bit DMA initialized
[ 1324.140927] Registered led device: b43legacy-phy0:tx
[ 1324.140948] Registered led device: b43legacy-phy0:rx
[ 1324.140967] Registered led device: b43legacy-phy0:radio
[ 1324.140992] b43legacy-phy0 debug: Wireless interface started
[ 1324.140996] b43legacy-phy0 debug: Adding Interface type 3
[ 1324.161293] wlan0: Trigger new scan to find an IBSS to join
[ 1324.884035] b43legacy-phy0: Radio hardware status changed to DISABLE=
D
[ 1324.884253] b43legacy-phy0 debug: Radio initialized
[ 1324.968031] b43legacy-phy0: Radio turned on by software
[ 1324.968040] b43legacy-phy0: The hardware RF-kill button still turns=20
the radio physically off. Press the button to turn it on.
[ 1326.968047] wlan0: Trigger new scan to find an IBSS to join
[ 1329.744048] wlan0: Trigger new scan to find an IBSS to join
[ 1332.520047] wlan0: Trigger new scan to find an IBSS to join
[ 1333.296087] wlan0: Creating new IBSS network, BSSID 76:0d:1d:b5:b7:7=
3
[ 1333.296126] wlan0: Configured IBSS beacon template
[ 1334.644033] wlan0: no IPv6 routers present
[ 1363.296044] wlan0: No active IBSS STAs - trying to scan for other=20
IBSS networks with same SSID (merge)
[ 1394.072046] wlan0: No active IBSS STAs - trying to scan for other=20
IBSS networks with same SSID (merge)
[ 1405.964030] wlan0: no IPv6 routers present
[ 1517.772022] phy0: Adding new IBSS station 00:30:6e:d2:4a:99 (dev=3Dw=
lan0)
[ 1517.772037] wlan0: expiring inactive STA 00:30:6e:d2:4a:99
[ 1517.772037] wlan0: No active IBSS STAs - trying to scan for other=20
IBSS networks with same SSID (merge)
[ 1574.332043] wlan0: No active IBSS STAs - trying to scan for other=20
IBSS networks with same SSID (merge)
[ 1582.205006] phy0: Adding new IBSS station 00:30:6e:d2:4a:99 (dev=3Dw=
lan0)
[ 1605.112054] wlan0: expiring inactive STA 00:30:6e:d2:4a:99
[ 1605.128043] wlan0: No active IBSS STAs - trying to scan for other=20
IBSS networks with same SSID (merge)
[ 1635.908058] wlan0: No active IBSS STAs - trying to scan for other=20
IBSS networks with same SSID (merge)
[ 1666.684045] wlan0: No active IBSS STAs - trying to scan for other=20

IBSS networks with same SSID (merge)

The Mac Adress "00:30:6e:d2:4a:99" is from my wireless Printer

Regards Markus

--
To unsubscribe from this list: send the line "unsubscribe linux-wireles= s" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html

#8 lore raw
Quoted 7 lines · feldmaus

i thought it would be helpful to post my Messages. :-) If not ignore this Message.:-)

I am using the NetworkManager Applet to show and connect to Wlan Networks. My wireless Button shines blue when my Linux System starts. However after i login onto myGnome Desktop and after some time the NetworkManager Applet shows me my Wireless Network.

You should check the posting at
http://www.ussg.iu.edu/hypermail/linux/kernel/0809.3/1423.html.
Perhaps you can activate your radio by software, even if the button does not work.

Larry

author
#9 lore raw
In reply to feldmaus

Hi All,

My actually Sydtem is:
HP Pavilion Laptop zv5000
Debian Lenny(Testing)
Linux Kernel 2.6.28 from kernel.org
Broadcom Wlan card BCM4303

My System doesnt work at all.

My Boot Messages are:

[   21.331095] b43legacy-phy0: Broadcom 4301 WLAN found
[   21.412214] b43legacy-phy0 debug: Found PHY: Analog 0, Type 1, Revision 4
[   21.412240] b43legacy-phy0 debug: Found Radio: Manuf 0x17F, Version 0x2050, Revision 2
[   21.436305] b43legacy-phy0 debug: Radio initialized
[   40.529192] input: b43legacy-phy0 as /class/input/input9
[   40.632070] b43legacy ssb0:0: firmware: requesting b43legacy/ucode2.fw
[   40.696281] b43legacy ssb0:0: firmware: requesting b43legacy/pcm4.fw
[   40.757265] b43legacy ssb0:0: firmware: requesting b43legacy/b0g0initvals2.fw
[   40.984045] b43legacy-phy0: Loading firmware version 0x127, patch level 14 (2005-04-18 02:36:27)
[   41.100298] b43legacy-phy0 debug: Chip initialized
[   41.100599] b43legacy-phy0 debug: 30-bit DMA initialized
[   41.100748] Registered led device: b43legacy-phy0:tx
[   41.109182] Registered led device: b43legacy-phy0:rx
[   41.117508] Registered led device: b43legacy-phy0:radio
[   41.125678] b43legacy-phy0 debug: Wireless interface started
[   41.125685] b43legacy-phy0 debug: Adding Interface type 2
[   41.584048] b43legacy-phy0: Radio hardware status changed to DISABLED
[   41.593709] b43legacy-phy0 debug: Radio initialized
[   41.924035] b43legacy-phy0: Radio turned on by software
[   41.932354] b43legacy-phy0: The hardware RF-kill button still turns the radio physically off. Press the button to turn it on.

Actually i am looking whether i missing some Kernel Options.

As we can see in the Boot Messages i have to activate the RF-kill Button by pressing, but this does not activate my wlan.

Any Ideas?

Regards Markus

author
#10 lore raw

I forgot to wrote my Kernel Options
CONFIG_LEDS_CLASS=m
CONFIG_LEDS_TRIGGERS=y
CONFIG_MAC80211_LEDS=y

CONFIG_RFKILL=m
CONFIG_RFKILL_INPUT=m
CONFIG_INPUT_POLLDEV=m

My b43legacy Driver is built as modul.

Regards Markus

author
#11 lore raw

I forgot to send my loaded modules.

The following Modules are loaded:

Module                  Size  Used by
nvidia               4699728  22
rfkill_input            4352  0
rfcomm                 29460  0
l2cap                  16772  5 rfcomm
bluetooth              45284  4 rfcomm,l2cap
ipv6                  221120  12
ipt_LOG                 4864  1
ipt_MASQUERADE          2560  1
xt_tcpudp               2816  33
xt_state                2048  4
ppdev                   6404  0
lp                      7916  0
powernow_k8            10764  0
cpufreq_userspace       2712  0
cpufreq_stats           3076  0
cpufreq_powersave       1536  0
cpufreq_ondemand        6016  1
freq_table              4100  3 powernow_k8,cpufreq_stats,cpufreq_ondemand
cpufreq_conservative     5280  0
iptable_filter          2560  1
nls_utf8                1792  1
nls_cp437               5504  1
vfat                    8832  1
fat                    42268  1 vfat
nls_base                6400  4 nls_utf8,nls_cp437,vfat,fat
iptable_nat             4868  1
ip_tables               9744  2 iptable_filter,iptable_nat
nf_nat                 15884  2 ipt_MASQUERADE,iptable_nat
x_tables               13060  6 ipt_LOG,ipt_MASQUERADE,xt_tcpudp,xt_state,iptable_nat,ip_tables
nf_conntrack_ipv4      11532  7 iptable_nat,nf_nat
nf_conntrack           55744  5 ipt_MASQUERADE,xt_state,iptable_nat,nf_nat,nf_conntrack_ipv4
nf_defrag_ipv4          1920  1 nf_conntrack_ipv4
loop                   12556  0
joydev                  8512  0
arc4                    1792  2
ecb                     2560  2
b43legacy              99356  0
rfkill                  9648  3 rfkill_input,b43legacy
rng_core                3844  1 b43legacy
mac80211              134172  1 b43legacy
snd_intel8x0m          12172  0
snd_pcm_oss            31776  0
snd_mixer_oss          12160  1 snd_pcm_oss
psmouse                37520  0
snd_intel8x0           25884  1
snd_ac97_codec         91556  2 snd_intel8x0m,snd_intel8x0
ac97_bus                1664  1 snd_ac97_codec
snd_pcm                61192  4 snd_intel8x0m,snd_pcm_oss,snd_intel8x0,snd_ac97_codec
parport_pc             22160  1
parport                30024  3 ppdev,lp,parport_pc
serio_raw               4740  0
cfg80211               26640  1 mac80211
led_class               3844  1 b43legacy
input_polldev           3720  1 b43legacy
pcspkr                  2304  0
yenta_socket           21388  2
rsrc_nonstatic          9728  1 yenta_socket
wmi                     6568  0
video                  16528  0
output                  2816  1 video
battery                10116  0
snd_seq_dummy           2692  0
container               3456  0
ac                      4100  0
button                  6032  0
snd_seq_oss            25236  0
k8temp                  3968  0
snd_seq_midi            5792  0
snd_rawmidi            18720  1 snd_seq_midi
shpchp                 27156  0
snd_seq_midi_event      6528  2 snd_seq_oss,snd_seq_midi
snd_seq                42144  6 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event
pci_hotplug            23456  1 shpchp
snd_timer              17540  2 snd_pcm,snd_seq
snd_seq_device          6412  5 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi,snd_seq
snd                    44980  13 snd_intel8x0m,snd_pcm_oss,snd_mixer_oss,snd_intel8x0,snd_ac97_codec,snd_pcm,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
amd64_agp               9096  1
soundcore               5956  1 snd
snd_page_alloc          8072  3 snd_intel8x0m,snd_intel8x0,snd_pcm
i2c_nforce2             6144  0
i2c_core               20880  2 nvidia,i2c_nforce2
agpgart                30128  2 nvidia,amd64_agp
evdev                   8068  7
ext2                   52104  2
mbcache                 6784  1 ext2
ide_cd_mod             31496  0
ide_gd_mod             13060  5
cdrom                  29848  1 ide_cd_mod
ata_generic             4612  0
libata                149472  1 ata_generic
scsi_mod              136208  1 libata
ide_pci_generic         3588  0
b44                    22800  0
usbhid                 28244  0
hid                    33868  1 usbhid
ssb                    34692  2 b43legacy,b44
8139too                21120  0
ohci1394               25776  0
pcmcia                 30388  1 ssb
pcmcia_core            30992  4 yenta_socket,rsrc_nonstatic,ssb,pcmcia
8139cp                 17664  0
mii                     4864  3 b44,8139too,8139cp
ieee1394               74684  1 ohci1394
amd74xx                 5640  4
ide_core               94748  4 ide_cd_mod,ide_gd_mod,ide_pci_generic,amd74xx
ehci_hcd               29964  0
ohci_hcd               20240  0
usbcore               121408  4 usbhid,ehci_hcd,ohci_hcd
thermal                15260  0
processor              35376  3 powernow_k8,thermal
fan                     4356  0
thermal_sys            10528  4 video,thermal,processor,fan

Regards Markus

#12 lore raw
In reply to feldmaus
Quoted 35 lines · feldmaus

Hi All,

My actually Sydtem is:
HP Pavilion Laptop zv5000
Debian Lenny(Testing)
Linux Kernel 2.6.28 from kernel.org
Broadcom Wlan card BCM4303

My System doesnt work at all.

My Boot Messages are:

[   21.331095] b43legacy-phy0: Broadcom 4301 WLAN found
[   21.412214] b43legacy-phy0 debug: Found PHY: Analog 0, Type 1,
Revision 4
[   21.412240] b43legacy-phy0 debug: Found Radio: Manuf 0x17F, Version
0x2050, Revision 2
[   21.436305] b43legacy-phy0 debug: Radio initialized
[   40.529192] input: b43legacy-phy0 as /class/input/input9
[   40.632070] b43legacy ssb0:0: firmware: requesting b43legacy/ucode2.fw
[   40.696281] b43legacy ssb0:0: firmware: requesting b43legacy/pcm4.fw
[   40.757265] b43legacy ssb0:0: firmware: requesting
b43legacy/b0g0initvals2.fw
[   40.984045] b43legacy-phy0: Loading firmware version 0x127, patch
level 14 (2005-04-18 02:36:27)
[   41.100298] b43legacy-phy0 debug: Chip initialized
[   41.100599] b43legacy-phy0 debug: 30-bit DMA initialized
[   41.100748] Registered led device: b43legacy-phy0:tx
[   41.109182] Registered led device: b43legacy-phy0:rx
[   41.117508] Registered led device: b43legacy-phy0:radio
[   41.125678] b43legacy-phy0 debug: Wireless interface started
[   41.125685] b43legacy-phy0 debug: Adding Interface type 2
[   41.584048] b43legacy-phy0: Radio hardware status changed to DISABLED
[   41.593709] b43legacy-phy0 debug: Radio initialized
[   41.924035] b43legacy-phy0: Radio turned on by software
[   41.932354] b43legacy-phy0: The hardware RF-kill button still turns
Quoted 7 lines

the radio physically off. Press the button to turn it on.

Actually i am looking whether i missing some Kernel Options.

As we can see in the Boot Messages i have to activate the RF-kill Button by pressing, but this does not activate my wlan.

Your log does not indicate that you pressed the button to turn the wifi on. All we see is that the hardware switch was off.

Is your radio on/off button one that generates a keycode, or does it need the WMI magic to be detected? If you are running X, then switch away by CTRL/ALT/F1 and log in. Use the showkey command and press the radio on/off switch. If it shows a scan code, report it back here. You get back to X with CTRL/ALT/F7.

Larry

author
#13 lore raw
Quoted 2 lines · Larry Finger

Your log does not indicate that you pressed the button to turn the wifi on. All we see is that the hardware switch was off.

You are right. I pressed the Hardware wlan Button, but the LED Light does not change. And the program <acpi_listen> does not show that any acpi signal is sended.

I am not sure whether i can watch this signals with <acpi_listen>.

Quoted 6 lines

Is your radio on/off button one that generates a keycode, or does it need the WMI magic to be detected? If you are running X, then switch away by CTRL/ALT/F1 and log in. Use the showkey command and press the radio on/off switch. If it shows a scan code, report it back here. You get back to X with CTRL/ALT/F7.

Ok i tried <showkey> during pressing my hardware butto in a VT, but this shows nothing.
I have "hp Extras" as modul. Other buttons on my Laptop are working.

I can activate/deactivate the wlan led by using the netwotkmanager applet <nm-applet> under gnome.

What is WMI Magic ?

Regards Markus

author
#14 lore raw
In reply to Larry Finger
Quoted 2 lines · Larry Finger

Your log does not indicate that you pressed the button to turn the wifi on. All we see is that the hardware switch was off.

Yes you are right.

Here is the log during Boot up:

[   21.389448] b43legacy-phy0: Broadcom 4301 WLAN found
[   21.451790] b43legacy-phy0 debug: Found PHY: Analog 0, Type 1, Revision 4
[   21.451814] b43legacy-phy0 debug: Found Radio: Manuf 0x17F, Version 0x2050, Revision 2
[   21.488040] b43legacy-phy0 debug: Radio initialized
[   41.176020] input: b43legacy-phy0 as /class/input/input9
[   41.276065] b43legacy ssb0:0: firmware: requesting b43legacy/ucode2.fw
[   41.340931] b43legacy ssb0:0: firmware: requesting b43legacy/pcm4.fw
[   41.415190] b43legacy ssb0:0: firmware: requesting b43legacy/b0g0initvals2.fw
[   41.624053] b43legacy-phy0: Loading firmware version 0x127, patch level 14 (2005-04-18 02:36:27)
[   41.736308] b43legacy-phy0 debug: Chip initialized
[   41.736617] b43legacy-phy0 debug: 30-bit DMA initialized
[   41.736769] Registered led device: b43legacy-phy0:tx
[   41.744956] Registered led device: b43legacy-phy0:rx
[   41.753043] Registered led device: b43legacy-phy0:radio
[   41.760983] b43legacy-phy0 debug: Wireless interface started
[   41.760990] b43legacy-phy0 debug: Adding Interface type 2
[   42.221213] b43legacy-phy0: Radio hardware status changed to DISABLED
[   42.230568] b43legacy-phy0 debug: Radio initialized
[   42.512043] b43legacy-phy0: Radio turned on by software
[   42.520110] b43legacy-phy0: The hardware RF-kill button still turns the radio physically off. Press the button to turn it on.

Then i deactivated the wlan with my networkmanager:

[  626.730050] b43legacy-phy0 debug: Removing Interface type 2
[  626.738361] b43legacy-phy0 debug: Wireless interface stopped
[  626.738524] b43legacy-phy0 debug: DMA-30 0x0260 (RX) max used slots: 1/64
[  626.738579] b43legacy-phy0 debug: DMA-30 0x0200 (RX) max used slots: 0/64
[  626.738643] b43legacy-phy0 debug: DMA-30 0x02A0 (TX) max used slots: 0/128
[  626.744048] b43legacy-phy0 debug: DMA-30 0x0280 (TX) max used slots: 0/128
[  626.752047] b43legacy-phy0 debug: DMA-30 0x0260 (TX) max used slots: 0/128
[  626.762293] b43legacy-phy0 debug: DMA-30 0x0240 (TX) max used slots: 0/128
[  626.768035] b43legacy-phy0 debug: DMA-30 0x0220 (TX) max used slots: 2/128
[  626.776035] b43legacy-phy0 debug: DMA-30 0x0200 (TX) max used slots: 0/128
[  626.784038] b43legacy-phy0 debug: Radio initialized
[  626.784049] b43legacy-phy0 debug: Radio initialized

Then i activated my wlan with my networkmanager:

[  651.401677] input: b43legacy-phy0 as /class/input/input10
[  651.572038] b43legacy-phy0: Loading firmware version 0x127, patch level 14 (2005-04-18 02:36:27)
[  651.680310] b43legacy-phy0 debug: Chip initialized
[  651.680628] b43legacy-phy0 debug: 30-bit DMA initialized
[  651.680788] Registered led device: b43legacy-phy0:tx
[  651.680827] Registered led device: b43legacy-phy0:rx
[  651.680866] Registered led device: b43legacy-phy0:radio
[  651.680896] b43legacy-phy0 debug: Wireless interface started
[  651.680903] b43legacy-phy0 debug: Adding Interface type 2
[  652.420046] b43legacy-phy0: Radio hardware status changed to DISABLED

Regards Markus