Skip to contentSkip to conversation

Setting PL2303 baud rate

DISCUSSION Fernando Di Nucci 3 participants 3 messages May 6, 2013 TTY layer and serial drivers

lore
Share & tools
lore
#0 lore raw

I have a PL2303HX adapter and I need to set up its baud rate to 1228800 or 2457600

(openwrt, linux kernel 3.3.8, coreutils 8.16 and ubuntu quantal 3.5.0-28, same coreutils).

I tried stty -F /dev/ttyUSB0 baudrate

Well, when baudrate is 921600 or 3000000 everything is fine, but when I try 1228800 or 2457600 stty complaints:
stty: invalid argument '2457600'.

I searched stty source and added:

#ifdef B1228800
{"1228800", B1228800, 1228800},
#endif
#ifdef B2457600
{"2457600", B2457600, 2457600},
#endif

and compiled but no luck. I don't know where else those values need also to be modified.

Can you please point me to the right direction?

Or there is another way to set pl2303 baud rate passing some information on the command line of kernel module?

I searched the web but didn't find any clue.

Any help appreciated, thank you very much anyway.

#1 lore raw
Quoted 21 lines · Fernando Di Nucci

I have a PL2303HX adapter and I need to set up its baud rate to 1228800 or 2457600

(openwrt, linux kernel 3.3.8, coreutils 8.16 and ubuntu quantal 3.5.0-28, same coreutils).

I tried stty -F /dev/ttyUSB0 baudrate

Well, when baudrate is 921600 or 3000000 everything is fine, but when I try 1228800 or 2457600 stty complaints:
stty: invalid argument '2457600'.

I searched stty source and added:

#ifdef B1228800
   {"1228800", B1228800, 1228800},
#endif
#ifdef B2457600
   {"2457600", B2457600, 2457600},

#endif

Quoted 8 lines

and compiled but no luck. I don't know where else those values need also to be modified.

Can you please point me to the right direction?

Or there is another way to set pl2303 baud rate passing some information on the command line of kernel module?

I would _guess_ that the PL2303 driver is modern enough that it supports termios interface that allows application code to specify arbitrary baud rates -- so you could try that:

http://www.gossamer-threads.com/lists/python/python/1019389?do=post_view_threaded

Signature · 4 lines
Grant Edwards               grant.b.edwards        Yow! Should I get locked
                                  at               in the PRINCICAL'S
                              gmail.com            OFFICE today -- or have
                                                   a VASECTOMY??
#2 lore raw
In reply to Fernando Di Nucci
Quoted 21 lines · Fernando Di Nucci

I have a PL2303HX adapter and I need to set up its baud rate to 1228800 or 2457600

(openwrt, linux kernel 3.3.8, coreutils 8.16 and ubuntu quantal 3.5.0-28, same coreutils).

I tried stty -F /dev/ttyUSB0 baudrate

Well, when baudrate is 921600 or 3000000 everything is fine, but when I try 1228800 or 2457600 stty complaints:
stty: invalid argument '2457600'.

I searched stty source and added:

#ifdef B1228800
{"1228800", B1228800, 1228800},
#endif
#ifdef B2457600
{"2457600", B2457600, 2457600},
#endif

Quoted 4 lines

and compiled but no luck. I don't know where else those values need also to be modified.

Can you please point me to the right direction?

I don't think stty can handle the higher baud rates, you are going to have to do the tty ioctl commands yourself in your program.

Take a look at the cfsetospeed() man page for details.

Hope this helps,

greg k-h