mmc: meson: Assign the minimum clk rate as close to 100KHz as possible
Subsystems (2)
PATCH 1/1 mmc: meson: Assign the minimum clk rate as close to 100KHz as possible
The current code dealing with calculating mmc->f_min is a bit complicated. Additionally, the attempt to set an initial clock rate should explicitly use a rate between 100KHz to 400 KHz, according the (e)MMC/SD specs, which it doesn't.
Fix the problem and clean up the code by using clk_round_rate() to pick the nearest minimum rate to 100KHz.
---
Note, this is compile tested only so I hope someone with the HW can give it a go.
--- drivers/mmc/host/meson-gx-mmc.c | 19 ++++++------------- 1 file changed, 6 insertions(+), 13 deletions(-)
drivers/mmc/host/meson-gx-mmc.c +6 -13
@@ -240,7 +240,6 @@ static int meson_mmc_clk_init(struct meson_host *host)const char *mux_parent_names[MUX_CLK_NUM_PARENTS ];unsigned int mux_parent_count =0 ;const char *clk_div_parents[1 ]; -unsigned int f_min =UINT_MAX ;u32 clk_reg, cfg;/* get the mux parents */
@@ -257,20 +256,10 @@ static int meson_mmc_clk_init(struct meson_host *host)return ret; } - host->mux_parent_rate[i] =clk_get_rate (host->mux_parent[i]); mux_parent_names[i] =__clk_get_name (host->mux_parent[i]); mux_parent_count++; -if (host->mux_parent_rate[i] < f_min) - f_min = host->mux_parent_rate[i]; } -/* cacluate f_min based on input clocks, and max divider value */ -if (f_min !=UINT_MAX ) - f_min =DIV_ROUND_UP (CLK_SRC_XTAL_RATE ,CLK_DIV_MAX ); -else - f_min =4000000 ;/* default min: 400 MHz */ - host->mmc->f_min = f_min; -/* create the mux */ snprintf (clk_name,sizeof (clk_name),"%s#mux" ,dev_name (host->dev)); init.name = clk_name;
@@ -325,9 +314,13 @@ static int meson_mmc_clk_init(struct meson_host *host)writel (cfg, host->regs +SD_EMMC_CFG ); ret =clk_prepare_enable (host->cfg_div_clk); -if (!ret) - ret =meson_mmc_clk_set (host, f_min); +if (ret) +return ret; + +/* Get the nearest minimum clock to 100KHz */ + host->mmc->f_min =clk_round_rate (host->cfg_div_clk,100000 ); + ret =meson_mmc_clk_set (host, host->mmc->f_min);if (!ret)clk_disable_unprepare (host->cfg_div_clk);
Signature · 1 line
1.9.1
Kevin Hilman
maintainerPATCH 1/1 mmc: meson: Assign the minimum clk rate as close to 100KHz as possible
Quoted 5 lines · Ulf Hansson
The current code dealing with calculating
mmc->f_minis a bit complicated. Additionally, the attempt to set an initial clock rate should explicitly use a rate between 100KHz to 400 KHz, according the (e)MMC/SD specs, which it doesn't.
Quoted 8 lines
Fix the problem and clean up the code by using
clk_round_rate()to pick the nearest minimum rate to 100KHz.Signed-off-by Ulf Hansson <[email protected]>---
Note, this is compile tested only so I hope someone with the HW can give it a go.
Not being an MMC expert, I didn't fully understand how f_min was meant to be used by the core code, so the initial driver was simply calculating the lowest clock rate available based on the input clocks.
Thanks for cleaning that up.
Kevin
Quoted 52 lines
--- drivers/mmc/host/meson-gx-mmc.c | 19 ++++++------------- 1 file changed, 6 insertions(+), 13 deletions(-)drivers/mmc/host/meson-gx-mmc.c +6
-13@@ -240,7 +240,6 @@ static int meson_mmc_clk_init(struct meson_host *host)const char *mux_parent_names[MUX_CLK_NUM_PARENTS ];unsigned int mux_parent_count =0 ;const char *clk_div_parents[1 ]; -unsigned int f_min =UINT_MAX ;u32 clk_reg, cfg;/* get the mux parents */ @@ -257,20 +256,10 @@ static int meson_mmc_clk_init(struct meson_host *host)return ret; } - host->mux_parent_rate[i] =clk_get_rate (host->mux_parent[i]); mux_parent_names[i] =__clk_get_name (host->mux_parent[i]); mux_parent_count++; -if (host->mux_parent_rate[i] < f_min) - f_min = host->mux_parent_rate[i]; } -/* cacluate f_min based on input clocks, and max divider value */ -if (f_min !=UINT_MAX ) - f_min =DIV_ROUND_UP (CLK_SRC_XTAL_RATE ,CLK_DIV_MAX ); -else - f_min =4000000 ;/* default min: 400 MHz */ - host->mmc->f_min = f_min; -/* create the mux */ snprintf (clk_name,sizeof (clk_name),"%s#mux" ,dev_name (host->dev)); init.name = clk_name;@@ -325,9 +314,13 @@ static int meson_mmc_clk_init(struct meson_host *host)writel (cfg, host->regs +SD_EMMC_CFG ); ret =clk_prepare_enable (host->cfg_div_clk); -if (!ret) - ret =meson_mmc_clk_set (host, f_min); +if (ret) +return ret; + +/* Get the nearest minimum clock to 100KHz */ + host->mmc->f_min =clk_round_rate (host->cfg_div_clk,100000 ); + ret =meson_mmc_clk_set (host, host->mmc->f_min);if (!ret)clk_disable_unprepare (host->cfg_div_clk);