Solo6x10 driver

index 7bbb940..2b3d30b 100644
@@ -1034,13 +1034,17 @@ static int solo_enc_try_fmt_cap(struct file *file, void *priv,
 		if (pix->width != solo_enc->width ||
 		    pix->height != solo_enc->height)
 			return -EBUSY;
-	} else if (!(pix->width == solo_dev->video_hsize &&
-	      pix->height == solo_dev->video_vsize << 1) &&
-	    !(pix->width == solo_dev->video_hsize >> 1 &&
-	      pix->height == solo_dev->video_vsize)) {
+	}
+
+	if (pix->width < solo_dev->video_hsize ||
+	    pix->height < solo_dev->video_vsize << 1) {
 		/* Default to CIF 1/2 size */
 		pix->width = solo_dev->video_hsize >> 1;
 		pix->height = solo_dev->video_vsize;
+	} else {
+		/* Full frame */
+		pix->width = solo_dev->video_hsize;
+		pix->height = solo_dev->video_vsize << 1;
 	}
 
 	if (pix->field == V4L2_FIELD_ANY)

index d39d3c6..a1dad57 100644
@@ -402,46 +402,6 @@
 #define	  SOLO_DCT_INTERVAL(n)			((n)<<16)
 
 #define SOLO_VE_STATE(n)			(0x0640+((n)*4))
-struct videnc_status {
-	union {
-		u32 status0;
-		struct {
-			u32 mp4_enc_code_size:20, sad_motion:1, vid_motion:1,
-			    vop_type:2, video_channel:5, source_field_idx:1,
-			    interlace:1, progressive:1;
-		} status0_st;
-	};
-	union {
-		u32 status1;
-		struct {
-			u32 vsize:8, hsize:8, last_queue:4, foo1:8, scale:4;
-		} status1_st;
-	};
-	union {
-		u32 status4;
-		struct {
-			u32 jpeg_code_size:20, interval:10, foo1:2;
-		} status4_st;
-	};
-	union {
-		u32 status9;
-		struct {
-			u32 channel:5, foo1:27;
-		} status9_st;
-	};
-	union {
-		u32 status10;
-		struct {
-			u32 mp4_code_size:20, foo:12;
-		} status10_st;
-	};
-	union {
-		u32 status11;
-		struct {
-			u32 last_queue:8, foo1:24;
-		} status11_st;
-	};
-};
 
 #define SOLO_VE_JPEG_QP_TBL			0x0670
 #define SOLO_VE_JPEG_QP_CH_L			0x0674

262 lines not on this page · raw message

index 481a492..7e28f7d 100644
@@ -176,7 +176,6 @@ static void solo_mp4e_config(struct solo6010_dev *solo_dev)
 		       SOLO_VE_BLOCK_BASE(SOLO_MP4E_EXT_ADDR(solo_dev) >> 16));
 
 	solo_reg_write(solo_dev, SOLO_VE_CFG1,
-		       SOLO_VE_BYTE_ALIGN(2) |
 		       SOLO_VE_INSERT_INDEX | SOLO_VE_MOTION_MODE(0));
 
 	solo_reg_write(solo_dev, SOLO_VE_WMRK_POLY, 0);

index 47f6e04..ccee5b8 100644
@@ -754,7 +754,7 @@ void solo_enc_v4l2_isr(struct solo6010_dev *solo_dev)
 
 	cur_q = ((solo_reg_read(solo_dev, SOLO_VE_STATE(11)) & 0xF) + 1) % MP4_QS;
 
-	reg_mpeg_size = ((solo_reg_read(solo_dev, SOLO_VE_STATE(0)) & 0xFFFFF) + 64 + 32) & ~31;
+	reg_mpeg_size = ((solo_reg_read(solo_dev, SOLO_VE_STATE(0)) & 0xFFFFF) + 64 + 8) & ~7;
 
 	while (solo_dev->enc_idx != cur_q) {
 		mpeg_current = solo_reg_read(solo_dev,

index c433136..c713a74 100644
@@ -136,6 +136,7 @@ static int __devinit solo6010_pci_probe(struct pci_dev *pdev,
 	int ret;
 	int sdram;
 	u8 chip_id;
+	u32 reg;
 
 	solo_dev = kzalloc(sizeof(*solo_dev), GFP_KERNEL);
 	if (solo_dev == NULL)

@@ -181,14 +182,43 @@ static int __devinit solo6010_pci_probe(struct pci_dev *pdev,
 		solo_dev->nr_ext = 1;
 	}
 
+	solo_dev->flags = id->driver_data;
+
 	/* Disable all interrupts to start */
 	solo6010_irq_off(solo_dev, ~0);
 
+	reg = SOLO_SYS_CFG_SDRAM64BIT;
 	/* Initial global settings */
-	solo_reg_write(solo_dev, SOLO_SYS_CFG, SOLO_SYS_CFG_SDRAM64BIT |
-		       SOLO_SYS_CFG_INPUTDIV(25) |
-		       SOLO_SYS_CFG_FEEDBACKDIV((SOLO_CLOCK_MHZ * 2) - 2) |
-		       SOLO_SYS_CFG_OUTDIV(3));
+	if (!(solo_dev->flags & FLAGS_6110))
+		reg |= SOLO6010_SYS_CFG_INPUTDIV(25) |
+			SOLO6010_SYS_CFG_FEEDBACKDIV((SOLO_CLOCK_MHZ * 2) - 2) |
+			SOLO6010_SYS_CFG_OUTDIV(3);
+	solo_reg_write(solo_dev, SOLO_SYS_CFG, reg);
+
+        if (solo_dev->flags & FLAGS_6110) {
+                u32 sys_clock_MHz = SOLO_CLOCK_MHZ;
+                u32 pll_DIVQ;
+                u32 pll_DIVF;
+
+                if (sys_clock_MHz < 125) {
+                        pll_DIVQ = 3;
+                        pll_DIVF = (sys_clock_MHz * 4) / 3;
+                } else {
+                        pll_DIVQ = 2;
+                        pll_DIVF = (sys_clock_MHz * 2) / 3;
+                }
+
+                solo_reg_write(solo_dev, SOLO6110_PLL_CONFIG,
+			       SOLO6110_PLL_RANGE_5_10MHZ |
+			       SOLO6110_PLL_DIVR(9) |
+			       SOLO6110_PLL_DIVQ_EXP(pll_DIVQ) |
+			       SOLO6110_PLL_DIVF(pll_DIVF) | SOLO6110_PLL_FSEN);
+		mdelay(1);      // PLL Locking time (1ms)
+
+		solo_reg_write(solo_dev, SOLO_DMA_CTRL1, 3 << 8); /* ? */
+        } else
+		solo_reg_write(solo_dev, SOLO_DMA_CTRL1, 1 << 8); /* ? */
+
 	solo_reg_write(solo_dev, SOLO_TIMER_CLOCK_NUM, SOLO_CLOCK_MHZ - 1);
 
 	/* PLL locking time of 1ms */

@@ -264,6 +294,8 @@ static void __devexit solo6010_pci_remove(struct pci_dev *pdev)
 static struct pci_device_id solo6010_id_table[] = {
 	/* 6010 based cards */
 	{PCI_DEVICE(PCI_VENDOR_ID_SOFTLOGIC, PCI_DEVICE_ID_SOLO6010)},
+	{PCI_DEVICE(PCI_VENDOR_ID_SOFTLOGIC, PCI_DEVICE_ID_SOLO6110),
+	 .driver_data = FLAGS_6110},
 	{PCI_DEVICE(PCI_VENDOR_ID_BLUECHERRY, PCI_DEVICE_ID_NEUSOLO_4)},
 	{PCI_DEVICE(PCI_VENDOR_ID_BLUECHERRY, PCI_DEVICE_ID_NEUSOLO_9)},
 	{PCI_DEVICE(PCI_VENDOR_ID_BLUECHERRY, PCI_DEVICE_ID_NEUSOLO_16)},

index 7e28f7d..743734d 100644
@@ -155,19 +155,26 @@ int solo_osd_print(struct solo_enc_dev *solo_enc)
 
 static void solo_jpeg_config(struct solo6010_dev *solo_dev)
 {
-	solo_reg_write(solo_dev, SOLO_VE_JPEG_QP_TBL,
-		       (2 << 24) | (2 << 16) | (2 << 8) | (2 << 0));
+	u32 reg;
+	if (solo_dev->flags & FLAGS_6110)
+		reg = (4 << 24) | (3 << 16) | (2 << 8) | (1 << 0);
+	else
+		reg = (2 << 24) | (2 << 16) | (2 << 8) | (2 << 0);
+	solo_reg_write(solo_dev, SOLO_VE_JPEG_QP_TBL, reg);
 	solo_reg_write(solo_dev, SOLO_VE_JPEG_QP_CH_L, 0);
 	solo_reg_write(solo_dev, SOLO_VE_JPEG_QP_CH_H, 0);
 	solo_reg_write(solo_dev, SOLO_VE_JPEG_CFG,
 		(SOLO_JPEG_EXT_SIZE(solo_dev) & 0xffff0000) |
 		((SOLO_JPEG_EXT_ADDR(solo_dev) >> 16) & 0x0000ffff));
 	solo_reg_write(solo_dev, SOLO_VE_JPEG_CTRL, 0xffffffff);
+	/* que limit, samp limit, pos limit */
+	solo_reg_write(solo_dev, 0x0688, (0 << 16) | (30 << 8) | 60);
 }
 
 static void solo_mp4e_config(struct solo6010_dev *solo_dev)
 {
 	int i;
+	u32 reg;
 
 	/* We can only use VE_INTR_CTRL(0) if we want to support mjpeg */
 	solo_reg_write(solo_dev, SOLO_VE_CFG0,

@@ -184,17 +191,21 @@ static void solo_mp4e_config(struct solo6010_dev *solo_dev)
 	solo_reg_write(solo_dev, SOLO_VE_ENCRYP_POLY, 0);
 	solo_reg_write(solo_dev, SOLO_VE_ENCRYP_INIT, 0);
 
-	solo_reg_write(solo_dev, SOLO_VE_ATTR,
-		       SOLO_VE_LITTLE_ENDIAN |
-		       SOLO_COMP_ATTR_FCODE(1) |
-		       SOLO_COMP_TIME_INC(0) |
-		       SOLO_COMP_TIME_WIDTH(15) |
-		       SOLO_DCT_INTERVAL(36 / 4));
+	reg = SOLO_VE_LITTLE_ENDIAN | SOLO_COMP_ATTR_FCODE(1) |
+		SOLO_COMP_TIME_INC(0) | SOLO_COMP_TIME_WIDTH(15);
+	if (solo_dev->flags & FLAGS_6110)
+		reg |= SOLO_DCT_INTERVAL(10);
+	else
+		reg |= SOLO_DCT_INTERVAL(36 / 4);
+	solo_reg_write(solo_dev, SOLO_VE_ATTR, reg);
 
 	for (i = 0; i < solo_dev->nr_chans; i++)
 		solo_reg_write(solo_dev, SOLO_VE_CH_REF_BASE(i),
 			       (SOLO_EREF_EXT_ADDR(solo_dev) +
 			       (i * SOLO_EREF_EXT_SIZE)) >> 16);
+
+	if (solo_dev->flags & FLAGS_6110)
+		solo_reg_write(solo_dev, 0x0634, 0x00040008); /* ? */
 }
 
 int solo_enc_init(struct solo6010_dev *solo_dev)

index 956dea0..90de963 100644
@@ -66,18 +66,18 @@ int solo_p2m_dma_t(struct solo6010_dev *solo_dev, u8 id, int wr,
 void solo_p2m_push_desc(struct p2m_desc *desc, int wr, dma_addr_t dma_addr,
 			u32 ext_addr, u32 size, int repeat, u32 ext_size)
 {
-	desc->ta = dma_addr;
-	desc->fa = ext_addr;
+	desc->ta = cpu_to_le32(dma_addr);
+	desc->fa = cpu_to_le32(ext_addr);
 
-	desc->ext = SOLO_P2M_COPY_SIZE(size >> 2);
-	desc->ctrl = SOLO_P2M_BURST_SIZE(SOLO_P2M_BURST_256) |
-		(wr ? SOLO_P2M_WRITE : 0) | SOLO_P2M_TRANS_ON;
+	desc->ext = cpu_to_le32(SOLO_P2M_COPY_SIZE(size >> 2));
+	desc->ctrl = cpu_to_le32(SOLO_P2M_BURST_SIZE(SOLO_P2M_BURST_256) |
+				 (wr ? SOLO_P2M_WRITE : 0) | SOLO_P2M_TRANS_ON);
 
 	/* Ext size only matters when we're repeating */
 	if (repeat) {
-		desc->ext |= SOLO_P2M_EXT_INC(ext_size >> 2);
-		desc->ctrl |=  SOLO_P2M_PCI_INC(size >> 2) |
-			SOLO_P2M_REPEAT(repeat);
+		desc->ext |= cpu_to_le32(SOLO_P2M_EXT_INC(ext_size >> 2));
+		desc->ctrl |=  cpu_to_le32(SOLO_P2M_PCI_INC(size >> 2) |
+					   SOLO_P2M_REPEAT(repeat));
 	}
 }
 

index a1dad57..db291bf 100644
@@ -24,16 +24,16 @@
 
 /* Global 6010 system configuration */
 #define SOLO_SYS_CFG				0x0000
-#define   SOLO_SYS_CFG_FOUT_EN			0x00000001
-#define   SOLO_SYS_CFG_PLL_BYPASS		0x00000002
-#define   SOLO_SYS_CFG_PLL_PWDN			0x00000004
-#define   SOLO_SYS_CFG_OUTDIV(__n)		(((__n) & 0x003) << 3)
-#define   SOLO_SYS_CFG_FEEDBACKDIV(__n)		(((__n) & 0x1ff) << 5)
-#define   SOLO_SYS_CFG_INPUTDIV(__n)		(((__n) & 0x01f) << 14)
+#define   SOLO6010_SYS_CFG_FOUT_EN		0x00000001 /* 6010 only */
+#define   SOLO6010_SYS_CFG_PLL_BYPASS		0x00000002 /* 6010 only */
+#define   SOLO6010_SYS_CFG_PLL_PWDN		0x00000004 /* 6010 only */
+#define   SOLO6010_SYS_CFG_OUTDIV(__n)		(((__n) & 0x003) << 3) /* 6010 only */
+#define   SOLO6010_SYS_CFG_FEEDBACKDIV(__n)	(((__n) & 0x1ff) << 5) /* 6010 only */
+#define   SOLO6010_SYS_CFG_INPUTDIV(__n)	(((__n) & 0x01f) << 14) /* 6010 only */
 #define   SOLO_SYS_CFG_CLOCK_DIV		0x00080000
 #define   SOLO_SYS_CFG_NCLK_DELAY(__n)		(((__n) & 0x003) << 24)
 #define   SOLO_SYS_CFG_PCLK_DELAY(__n)		(((__n) & 0x00f) << 26)
-#define   SOLO_SYS_CFG_SDRAM64BIT		0x40000000
+#define   SOLO_SYS_CFG_SDRAM64BIT		0x40000000 /* 6110: must be set */
 #define   SOLO_SYS_CFG_RESET			0x80000000
 
 #define	SOLO_DMA_CTRL				0x0004

@@ -45,6 +45,7 @@
 #define	  SOLO_DMA_CTRL_READ_DATA_SELECT	(1<<3)
 #define	  SOLO_DMA_CTRL_READ_CLK_SELECT		(1<<2)
 #define	  SOLO_DMA_CTRL_LATENCY(n)		((n)<<0)
+#define	SOLO_DMA_CTRL1				0x0008
 
 #define SOLO_SYS_VCLK				0x000C
 #define	  SOLO_VCLK_INVERT			(1<<22)

@@ -81,6 +82,23 @@
 #define SOLO_CHIP_OPTION			0x001C
 #define   SOLO_CHIP_ID_MASK			0x00000007
 
+#define SOLO6110_PLL_CONFIG			0x0020
+#define   SOLO6110_PLL_RANGE_BYPASS		(0 << 20)
+#define   SOLO6110_PLL_RANGE_5_10MHZ		(1 << 20)
+#define   SOLO6110_PLL_RANGE_8_16MHZ		(2 << 20)
+#define   SOLO6110_PLL_RANGE_13_26MHZ		(3 << 20)
+#define   SOLO6110_PLL_RANGE_21_42MHZ		(4 << 20)
+#define   SOLO6110_PLL_RANGE_34_68MHZ		(5 << 20)
+#define   SOLO6110_PLL_RANGE_54_108MHZ		(6 << 20)
+#define   SOLO6110_PLL_RANGE_88_200MHZ		(7 << 20)
+#define   SOLO6110_PLL_DIVR(x)			(((x) - 1) << 15)
+#define   SOLO6110_PLL_DIVQ_EXP(x)		((x) << 12)
+#define   SOLO6110_PLL_DIVF(x)			(((x) - 1) << 4)
+#define   SOLO6110_PLL_RESET			(1 << 3)
+#define   SOLO6110_PLL_BYPASS			(1 << 2)
+#define   SOLO6110_PLL_FSEN			(1 << 1)
+#define   SOLO6110_PLL_FB			(1 << 0)
+
 #define SOLO_EEPROM_CTRL			0x0060
 #define	  SOLO_EEPROM_ACCESS_EN			(1<<7)
 #define	  SOLO_EEPROM_CS			(1<<3)

@@ -383,7 +401,9 @@
 #define	  SOLO_VE_BLOCK_BASE(n)			((n)<<0)
 
 #define SOLO_VE_CFG1				0x0614
-#define	  SOLO_VE_BYTE_ALIGN(n)			((n)<<24)
+#define   SOLO6110_VE_MPEG_SIZE_H(n)		((n)<<28) /* 6110 only */
+#define	  SOLO6010_VE_BYTE_ALIGN(n)		((n)<<24) /* 6010 only */
+#define   SOLO6110_VE_JPEG_SIZE_H(n)		((n)<<20) /* 6110 only */
 #define	  SOLO_VE_INSERT_INDEX			(1<<18)
 #define	  SOLO_VE_MOTION_MODE(n)		((n)<<16)
 #define	  SOLO_VE_MOTION_BASE(n)		((n)<<0)

@@ -415,7 +435,7 @@
 #define SOLO_VE_OSD_OPT				0x069C
 
 #define SOLO_VE_CH_INTL(ch)			(0x0700+((ch)*4))
-#define SOLO_VE_CH_MOT(ch)			(0x0740+((ch)*4))
+#define SOLO6010_VE_CH_MOT(ch)			(0x0740+((ch)*4)) /* 6010 only */
 #define SOLO_VE_CH_QP(ch)			(0x0780+((ch)*4))
 #define SOLO_VE_CH_QP_E(ch)			(0x07C0+((ch)*4))
 #define SOLO_VE_CH_GOP(ch)			(0x0800+((ch)*4))

@@ -427,7 +447,7 @@
 #define SOLO_VE_JPEG_QUE(n)			(0x0A04+((n)*8))
 
 #define SOLO_VD_CFG0				0x0900
-#define	  SOLO_VD_CFG_NO_WRITE_NO_WINDOW	(1<<24)
+#define	  SOLO6010_VD_CFG_NO_WRITE_NO_WINDOW	(1<<24) /* 6010 only */
 #define	  SOLO_VD_CFG_BUSY_WIAT_CODE		(1<<23)
 #define	  SOLO_VD_CFG_BUSY_WIAT_REF		(1<<22)
 #define	  SOLO_VD_CFG_BUSY_WIAT_RES		(1<<21)

110 lines not on this page · raw message

index 9c930f3..4532e12 100644
@@ -40,6 +40,7 @@
 #ifndef PCI_VENDOR_ID_SOFTLOGIC
 #define PCI_VENDOR_ID_SOFTLOGIC		0x9413
 #define PCI_DEVICE_ID_SOLO6010		0x6010
+#define PCI_DEVICE_ID_SOLO6110		0x6110
 #endif
 
 #ifndef PCI_VENDOR_ID_BLUECHERRY

@@ -70,6 +71,8 @@
 #define SOLO6010_VER_NUM \
 	KERNEL_VERSION(SOLO6010_VER_MAJOR, SOLO6010_VER_MINOR, SOLO6010_VER_SUB)
 
+#define FLAGS_6110			1
+
 /*
  * The SOLO6010 actually has 8 i2c channels, but we only use 2.
  * 0 - Techwell chip(s)

@@ -183,6 +186,7 @@ struct solo6010_dev {
 	u8 __iomem		*reg_base;
 	int			nr_chans;
 	int			nr_ext;
+	u32			flags;
 	u32			irq_mask;
 	u32			motion_mask;
 	spinlock_t		reg_io_lock;

index f866f84..99d1461 100644
@@ -135,7 +135,7 @@ static void solo_disp_config(struct solo6010_dev *solo_dev)
 
 	solo_reg_write(solo_dev, SOLO_VO_DISP_CTRL, SOLO_VO_DISP_ON |
 		       SOLO_VO_DISP_ERASE_COUNT(8) |
-		       SOLO_VO_DISP_BASE(SOLO_DISP_EXT_ADDR(solo_dev)));
+		       SOLO_VO_DISP_BASE(SOLO_DISP_EXT_ADDR));
 
 	solo_reg_write(solo_dev, SOLO_VO_DISP_ERASE, SOLO_VO_DISP_ERASE_ON);
 

index 743734d..7a3c4d5 100644
@@ -93,8 +93,7 @@ static void solo_capture_config(struct solo6010_dev *solo_dev)
 
 	/* Clear OSD */
 	solo_reg_write(solo_dev, SOLO_VE_OSD_CH, 0);
-	solo_reg_write(solo_dev, SOLO_VE_OSD_BASE,
-		       SOLO_EOSD_EXT_ADDR(solo_dev) >> 16);
+	solo_reg_write(solo_dev, SOLO_VE_OSD_BASE, SOLO_EOSD_EXT_ADDR >> 16);
 	solo_reg_write(solo_dev, SOLO_VE_OSD_CLR,
 		       0xF0 << 16 | 0x80 << 8 | 0x80);
 	solo_reg_write(solo_dev, SOLO_VE_OSD_OPT, 0);

@@ -107,7 +106,7 @@ static void solo_capture_config(struct solo6010_dev *solo_dev)
 	for (i = 0; i < solo_dev->nr_chans; i++) {
 		for (j = 0; j < SOLO_EOSD_EXT_SIZE; j += OSG_BUFFER_SIZE) {
 			solo_p2m_dma(solo_dev, SOLO_P2M_DMA_ID_MP4E, 1, buf,
-				     SOLO_EOSD_EXT_ADDR(solo_dev) +
+				     SOLO_EOSD_EXT_ADDR +
 				     (i * SOLO_EOSD_EXT_SIZE) + j,
 				     OSG_BUFFER_SIZE);
 		}

@@ -143,7 +142,7 @@ int solo_osd_print(struct solo_enc_dev *solo_enc)
 		}
 	}
 
-	solo_p2m_dma(solo_dev, 0, 1, buf, SOLO_EOSD_EXT_ADDR(solo_dev) +
+	solo_p2m_dma(solo_dev, 0, 1, buf, SOLO_EOSD_EXT_ADDR +
 		     (solo_enc->ch * SOLO_EOSD_EXT_SIZE), SOLO_EOSD_EXT_SIZE);
 	reg |= (1 << solo_enc->ch);
 	solo_reg_write(solo_dev, SOLO_VE_OSD_CH, reg);

index 2431de9..b176003 100644
@@ -21,24 +21,20 @@
 #define __SOLO6010_OFFSETS_H
 
 /* Offsets and sizes of the external address */
-#define SOLO_DISP_EXT_ADDR(__solo)		0x00000000
+#define SOLO_DISP_EXT_ADDR			0x00000000
 #define SOLO_DISP_EXT_SIZE			0x00480000
 
-#define SOLO_DEC2LIVE_EXT_ADDR(__solo) \
-		(SOLO_DISP_EXT_ADDR(__solo) + SOLO_DISP_EXT_SIZE)
+#define SOLO_DEC2LIVE_EXT_ADDR (SOLO_DISP_EXT_ADDR + SOLO_DISP_EXT_SIZE)
 #define SOLO_DEC2LIVE_EXT_SIZE			0x00240000
 
-#define SOLO_OSG_EXT_ADDR(__solo) \
-		(SOLO_DEC2LIVE_EXT_ADDR(__solo) + SOLO_DEC2LIVE_EXT_SIZE)
+#define SOLO_OSG_EXT_ADDR (SOLO_DEC2LIVE_EXT_ADDR + SOLO_DEC2LIVE_EXT_SIZE)
 #define SOLO_OSG_EXT_SIZE			0x00120000
 
-#define SOLO_EOSD_EXT_ADDR(__solo) \
-		(SOLO_OSG_EXT_ADDR(__solo) + SOLO_OSG_EXT_SIZE)
+#define SOLO_EOSD_EXT_ADDR (SOLO_OSG_EXT_ADDR + SOLO_OSG_EXT_SIZE)
 #define SOLO_EOSD_EXT_SIZE			0x00010000
 
-#define SOLO_MOTION_EXT_ADDR(__solo) \
-		(SOLO_EOSD_EXT_ADDR(__solo) + \
-		 (SOLO_EOSD_EXT_SIZE * __solo->nr_chans))
+#define SOLO_MOTION_EXT_ADDR(__solo) (SOLO_EOSD_EXT_ADDR +	\
+				      (SOLO_EOSD_EXT_SIZE * __solo->nr_chans))
 #define SOLO_MOTION_EXT_SIZE			0x00080000
 
 #define SOLO_G723_EXT_ADDR(__solo) \

index a8491dc..4e24e92 100644
@@ -280,7 +280,7 @@ static void solo_fillbuf(struct solo_filehandle *fh,
 	sg_dma = sg_dma_address(sg);
 	sg_size_left = sg_dma_len(sg);
 
-	fdma_addr = SOLO_DISP_EXT_ADDR(solo_dev) + (fh->old_write *
+	fdma_addr = SOLO_DISP_EXT_ADDR + (fh->old_write *
 			(SOLO_HW_BPL * solo_vlines(solo_dev)));
 
 	for (i = 0; i < solo_vlines(solo_dev); i++) {

similarity index 99%
rename from drivers/staging/solo6x10/solo6010-core.c
rename to drivers/staging/solo6x10/core.c
index c713a74..37e6fda 100644
@@ -22,9 +22,8 @@
 #include <linux/pci.h>
 #include <linux/interrupt.h>
 #include <linux/videodev2.h>
-
-#include "solo6010.h"
-#include "solo6010-tw28.h"
+#include "solo6x10.h"
+#include "tw28.h"
 
 MODULE_DESCRIPTION("Softlogic 6010 MP4 Encoder/Decoder V4L2/ALSA Driver");
 MODULE_AUTHOR("Ben Collins <[email protected]>");

similarity index 99%
rename from drivers/staging/solo6x10/solo6010-disp.c
rename to drivers/staging/solo6x10/disp.c
index 99d1461..1b0cfa8 100644
@@ -21,8 +21,7 @@
 #include <linux/module.h>
 #include <linux/videodev2.h>
 #include <media/v4l2-ioctl.h>
-
-#include "solo6010.h"
+#include "solo6x10.h"
 
 #define SOLO_VCLK_DELAY			3
 #define SOLO_PROGRESSIVE_VSIZE		1024

similarity index 99%
rename from drivers/staging/solo6x10/solo6010-enc.c
rename to drivers/staging/solo6x10/enc.c
index 7a3c4d5..755626c 100644
@@ -18,9 +18,8 @@
  */
 
 #include <linux/kernel.h>
-
-#include "solo6010.h"
-#include "solo6010-osd-font.h"
+#include "solo6x10.h"
+#include "osd-font.h"
 
 #define CAPTURE_MAX_BANDWIDTH		32	/* D1 4channel (D1 == 4) */
 #define OSG_BUFFER_SIZE			1024

similarity index 99%
rename from drivers/staging/solo6x10/solo6010-g723.c
rename to drivers/staging/solo6x10/g723.c
index 254b46a..4aba8f3 100644
@@ -22,14 +22,12 @@
 #include <linux/poll.h>
 #include <linux/kthread.h>
 #include <linux/freezer.h>
-
 #include <sound/core.h>
 #include <sound/initval.h>
 #include <sound/pcm.h>
 #include <sound/control.h>
-
-#include "solo6010.h"
-#include "solo6010-tw28.h"
+#include "solo6x10.h"
+#include "tw28.h"
 
 #define G723_INTR_ORDER		0
 #define G723_FDMA_PAGES		32

similarity index 99%
rename from drivers/staging/solo6x10/solo6010-gpio.c
rename to drivers/staging/solo6x10/gpio.c
index 8869b88..efd88ba 100644
@@ -20,8 +20,7 @@
 #include <linux/kernel.h>
 #include <linux/fs.h>
 #include <asm/uaccess.h>
-
-#include "solo6010.h"
+#include "solo6x10.h"
 
 static void solo_gpio_mode(struct solo6010_dev *solo_dev,
 			   unsigned int port_mask, unsigned int mode)

similarity index 99%
rename from drivers/staging/solo6x10/solo6010-i2c.c
rename to drivers/staging/solo6x10/i2c.c
index 60b69cd..fba4247 100644
@@ -26,8 +26,7 @@
  * thread context, ACK the interrupt, and move on. -- BenC */
 
 #include <linux/kernel.h>
-
-#include "solo6010.h"
+#include "solo6x10.h"
 
 u8 solo_i2c_readbyte(struct solo6010_dev *solo_dev, int id, u8 addr, u8 off)
 {

similarity index 100%
rename from drivers/staging/solo6x10/solo6010-jpeg.h
rename to drivers/staging/solo6x10/jpeg.h

similarity index 100%
rename from drivers/staging/solo6x10/solo6010-offsets.h
rename to drivers/staging/solo6x10/offsets.h

similarity index 100%
rename from drivers/staging/solo6x10/solo6010-osd-font.h
rename to drivers/staging/solo6x10/osd-font.h

similarity index 99%
rename from drivers/staging/solo6x10/solo6010-p2m.c
rename to drivers/staging/solo6x10/p2m.c
index 90de963..1b88d10 100644
@@ -19,8 +19,7 @@
 
 #include <linux/kernel.h>
 #include <linux/scatterlist.h>
-
-#include "solo6010.h"
+#include "solo6x10.h"
 
 /* #define SOLO_TEST_P2M */
 

similarity index 99%
rename from drivers/staging/solo6x10/solo6010-registers.h
rename to drivers/staging/solo6x10/registers.h
index db291bf..edf77e8 100644
@@ -20,7 +20,7 @@
 #ifndef __SOLO6010_REGISTERS_H
 #define __SOLO6010_REGISTERS_H
 
-#include "solo6010-offsets.h"
+#include "offsets.h"
 
 /* Global 6010 system configuration */
 #define SOLO_SYS_CFG				0x0000

similarity index 99%
rename from drivers/staging/solo6x10/solo6010.h
rename to drivers/staging/solo6x10/solo6x10.h
index 4532e12..1730f4d 100644
@@ -30,12 +30,10 @@
 #include <linux/delay.h>
 #include <asm/io.h>
 #include <asm/atomic.h>
-
 #include <linux/videodev2.h>
 #include <media/v4l2-dev.h>
 #include <media/videobuf-core.h>
-
-#include "solo6010-registers.h"
+#include "registers.h"
 
 #ifndef PCI_VENDOR_ID_SOFTLOGIC
 #define PCI_VENDOR_ID_SOFTLOGIC		0x9413

similarity index 99%
rename from drivers/staging/solo6x10/solo6010-tw28.c
rename to drivers/staging/solo6x10/tw28.c
index 905a6ad..0f3d1e4 100644
@@ -18,9 +18,8 @@
  */
 
 #include <linux/kernel.h>
-
-#include "solo6010.h"
-#include "solo6010-tw28.h"
+#include "solo6x10.h"
+#include "tw28.h"
 
 /* XXX: Some of these values are masked into an 8-bit regs, and shifted
  * around for other 8-bit regs. What are the magic bits in these values? */

similarity index 99%
rename from drivers/staging/solo6x10/solo6010-tw28.h
rename to drivers/staging/solo6x10/tw28.h
index a7eecfa..4862ac9 100644
@@ -20,7 +20,7 @@
 #ifndef __SOLO6010_TW28_H
 #define __SOLO6010_TW28_H
 
-#include "solo6010.h"
+#include "solo6x10.h"
 
 #define TW_NUM_CHIP				4
 #define TW_BASE_ADDR				0x28

similarity index 99%
rename from drivers/staging/solo6x10/solo6010-v4l2-enc.c
rename to drivers/staging/solo6x10/v4l2-enc.c
index 619fb9b..4c8d62d 100644
@@ -21,14 +21,12 @@
 #include <linux/module.h>
 #include <linux/kthread.h>
 #include <linux/freezer.h>
-
 #include <media/v4l2-ioctl.h>
 #include <media/v4l2-common.h>
 #include <media/videobuf-dma-sg.h>
-
-#include "solo6010.h"
-#include "solo6010-tw28.h"
-#include "solo6010-jpeg.h"
+#include "solo6x10.h"
+#include "tw28.h"
+#include "jpeg.h"
 
 #define MIN_VID_BUFFERS		4
 #define FRAME_BUF_SIZE		(128 * 1024)

similarity index 99%
rename from drivers/staging/solo6x10/solo6010-v4l2.c
rename to drivers/staging/solo6x10/v4l2.c
index 4e24e92..e9d620a 100644
@@ -21,13 +21,11 @@
 #include <linux/module.h>
 #include <linux/kthread.h>
 #include <linux/freezer.h>
-
 #include <media/v4l2-ioctl.h>
 #include <media/v4l2-common.h>
 #include <media/videobuf-dma-sg.h>
-
-#include "solo6010.h"
-#include "solo6010-tw28.h"
+#include "solo6x10.h"
+#include "tw28.h"
 
 #define SOLO_HW_BPL		2048
 #define SOLO_DISP_PIX_FIELD	V4L2_FIELD_INTERLACED

index 37e6fda..7677994 100644
@@ -25,27 +25,27 @@
 #include "solo6x10.h"
 #include "tw28.h"
 
-MODULE_DESCRIPTION("Softlogic 6010 MP4 Encoder/Decoder V4L2/ALSA Driver");
+MODULE_DESCRIPTION("Softlogic 6x10 MP4/H.264 Encoder/Decoder V4L2/ALSA Driver");
 MODULE_AUTHOR("Ben Collins <[email protected]>");
-MODULE_VERSION(SOLO6010_VERSION);
+MODULE_VERSION(SOLO6X10_VERSION);
 MODULE_LICENSE("GPL");
 
-void solo6010_irq_on(struct solo6010_dev *solo_dev, u32 mask)
+void solo_irq_on(struct solo_dev *solo_dev, u32 mask)
 {
 	solo_dev->irq_mask |= mask;
 	solo_reg_write(solo_dev, SOLO_IRQ_ENABLE, solo_dev->irq_mask);
 }
 
-void solo6010_irq_off(struct solo6010_dev *solo_dev, u32 mask)
+void solo_irq_off(struct solo_dev *solo_dev, u32 mask)
 {
 	solo_dev->irq_mask &= ~mask;
 	solo_reg_write(solo_dev, SOLO_IRQ_ENABLE, solo_dev->irq_mask);
 }
 
 /* XXX We should check the return value of the sub-device ISR's */
-static irqreturn_t solo6010_isr(int irq, void *data)
+static irqreturn_t solo_isr(int irq, void *data)
 {
-	struct solo6010_dev *solo_dev = data;
+	struct solo_dev *solo_dev = data;
 	u32 status;
 	int i;
 

@@ -88,7 +88,7 @@ static irqreturn_t solo6010_isr(int irq, void *data)
 	return IRQ_HANDLED;
 }
 
-static void free_solo_dev(struct solo6010_dev *solo_dev)
+static void free_solo_dev(struct solo_dev *solo_dev)
 {
 	struct pci_dev *pdev;
 

@@ -116,7 +116,7 @@ static void free_solo_dev(struct solo6010_dev *solo_dev)
 
 	/* Now cleanup the PCI device */
 	if (solo_dev->reg_base) {
-		solo6010_irq_off(solo_dev, ~0);
+		solo_irq_off(solo_dev, ~0);
 		pci_iounmap(pdev, solo_dev->reg_base);
 		free_irq(pdev->irq, solo_dev);
 	}

@@ -128,10 +128,10 @@ static void free_solo_dev(struct solo6010_dev *solo_dev)
 	kfree(solo_dev);
 }
 
-static int __devinit solo6010_pci_probe(struct pci_dev *pdev,
-					const struct pci_device_id *id)
+static int __devinit solo_pci_probe(struct pci_dev *pdev,
+				    const struct pci_device_id *id)
 {
-	struct solo6010_dev *solo_dev;
+	struct solo_dev *solo_dev;
 	int ret;
 	int sdram;
 	u8 chip_id;

@@ -151,7 +151,7 @@ static int __devinit solo6010_pci_probe(struct pci_dev *pdev,
 
 	pci_set_master(pdev);
 
-	ret = pci_request_regions(pdev, SOLO6010_NAME);
+	ret = pci_request_regions(pdev, SOLO6X10_NAME);
 	if (ret)
 		goto fail_probe;
 

@@ -184,7 +184,7 @@ static int __devinit solo6010_pci_probe(struct pci_dev *pdev,
 	solo_dev->flags = id->driver_data;
 
 	/* Disable all interrupts to start */
-	solo6010_irq_off(solo_dev, ~0);
+	solo_irq_off(solo_dev, ~0);
 
 	reg = SOLO_SYS_CFG_SDRAM64BIT;
 	/* Initial global settings */

@@ -223,13 +223,13 @@ static int __devinit solo6010_pci_probe(struct pci_dev *pdev,
 	/* PLL locking time of 1ms */
 	mdelay(1);
 
-	ret = request_irq(pdev->irq, solo6010_isr, IRQF_SHARED, SOLO6010_NAME,
+	ret = request_irq(pdev->irq, solo_isr, IRQF_SHARED, SOLO6X10_NAME,
 			  solo_dev);
 	if (ret)
 		goto fail_probe;
 
 	/* Handle this from the start */
-	solo6010_irq_on(solo_dev, SOLO_IRQ_PCI_ERR);
+	solo_irq_on(solo_dev, SOLO_IRQ_PCI_ERR);
 
 	ret = solo_i2c_init(solo_dev);
 	if (ret)

@@ -283,14 +283,14 @@ fail_probe:
 	return ret;
 }
 
-static void __devexit solo6010_pci_remove(struct pci_dev *pdev)
+static void __devexit solo_pci_remove(struct pci_dev *pdev)
 {
-	struct solo6010_dev *solo_dev = pci_get_drvdata(pdev);
+	struct solo_dev *solo_dev = pci_get_drvdata(pdev);
 
 	free_solo_dev(solo_dev);
 }
 
-static struct pci_device_id solo6010_id_table[] = {
+static struct pci_device_id solo_id_table[] = {
 	/* 6010 based cards */
 	{PCI_DEVICE(PCI_VENDOR_ID_SOFTLOGIC, PCI_DEVICE_ID_SOLO6010)},
 	{PCI_DEVICE(PCI_VENDOR_ID_SOFTLOGIC, PCI_DEVICE_ID_SOLO6110),

@@ -308,24 +308,24 @@ static struct pci_device_id solo6010_id_table[] = {
 	{0,}
 };
 
-MODULE_DEVICE_TABLE(pci, solo6010_id_table);
+MODULE_DEVICE_TABLE(pci, solo_id_table);
 
-static struct pci_driver solo6010_pci_driver = {
-	.name = SOLO6010_NAME,
-	.id_table = solo6010_id_table,
-	.probe = solo6010_pci_probe,
-	.remove = solo6010_pci_remove,
+static struct pci_driver solo_pci_driver = {
+	.name = SOLO6X10_NAME,
+	.id_table = solo_id_table,
+	.probe = solo_pci_probe,
+	.remove = solo_pci_remove,
 };
 
-static int __init solo6010_module_init(void)
+static int __init solo_module_init(void)
 {
-	return pci_register_driver(&solo6010_pci_driver);
+	return pci_register_driver(&solo_pci_driver);
 }
 
-static void __exit solo6010_module_exit(void)
+static void __exit solo_module_exit(void)
 {
-	pci_unregister_driver(&solo6010_pci_driver);
+	pci_unregister_driver(&solo_pci_driver);
 }
 
-module_init(solo6010_module_init);
-module_exit(solo6010_module_exit);
+module_init(solo_module_init);
+module_exit(solo_module_exit);

index 1b0cfa8..884c0eb 100644
@@ -37,7 +37,7 @@ static unsigned video_type;
 module_param(video_type, uint, 0644);
 MODULE_PARM_DESC(video_type, "video_type (0 = NTSC/Default, 1 = PAL)");
 
-static void solo_vin_config(struct solo6010_dev *solo_dev)
+static void solo_vin_config(struct solo_dev *solo_dev)
 {
 	solo_dev->vin_hstart = 8;
 	solo_dev->vin_vstart = 2;

@@ -97,7 +97,7 @@ static void solo_vin_config(struct solo6010_dev *solo_dev)
 		       SOLO_VI_PB_HSTOP(16 + 720));
 }
 
-static void solo_disp_config(struct solo6010_dev *solo_dev)
+static void solo_disp_config(struct solo_dev *solo_dev)
 {
 	solo_dev->vout_hstart = 6;
 	solo_dev->vout_vstart = 8;

@@ -145,7 +145,7 @@ static void solo_disp_config(struct solo6010_dev *solo_dev)
 	solo_reg_write(solo_dev, SOLO_WATCHDOG, 0);
 }
 
-static int solo_dma_vin_region(struct solo6010_dev *solo_dev, u32 off,
+static int solo_dma_vin_region(struct solo_dev *solo_dev, u32 off,
 			       u16 val, int reg_size)
 {
 	u16 buf[64];

@@ -163,7 +163,7 @@ static int solo_dma_vin_region(struct solo6010_dev *solo_dev, u32 off,
 	return ret;
 }
 
-void solo_set_motion_threshold(struct solo6010_dev *solo_dev, u8 ch, u16 val)
+void solo_set_motion_threshold(struct solo_dev *solo_dev, u8 ch, u16 val)
 {
 	if (ch > solo_dev->nr_chans)
 		return;

@@ -177,7 +177,7 @@ void solo_set_motion_threshold(struct solo6010_dev *solo_dev, u8 ch, u16 val)
  * threshold and working table for each channel. Atleast that's what the
  * spec says. However, this code (take from rdk) has some mystery 8k
  * block right after the flag area, before the first thresh table. */
-static void solo_motion_config(struct solo6010_dev *solo_dev)
+static void solo_motion_config(struct solo_dev *solo_dev)
 {
 	int i;
 

@@ -209,7 +209,7 @@ static void solo_motion_config(struct solo6010_dev *solo_dev)
 	solo_reg_write(solo_dev, SOLO_VI_MOTION_BAR, 0);
 }
 
-int solo_disp_init(struct solo6010_dev *solo_dev)
+int solo_disp_init(struct solo_dev *solo_dev)
 {
 	int i;
 

@@ -234,11 +234,11 @@ int solo_disp_init(struct solo6010_dev *solo_dev)
 	return 0;
 }
 
-void solo_disp_exit(struct solo6010_dev *solo_dev)
+void solo_disp_exit(struct solo_dev *solo_dev)
 {
 	int i;
 
-	solo6010_irq_off(solo_dev, SOLO_IRQ_MOTION);
+	solo_irq_off(solo_dev, SOLO_IRQ_MOTION);
 
 	solo_reg_write(solo_dev, SOLO_VO_DISP_CTRL, 0);
 	solo_reg_write(solo_dev, SOLO_VO_ZOOM_CTRL, 0);

index 755626c..285f7f3 100644
@@ -27,7 +27,7 @@
 #define VI_PROG_HSIZE			(1280 - 16)
 #define VI_PROG_VSIZE			(1024 - 16)
 
-static void solo_capture_config(struct solo6010_dev *solo_dev)
+static void solo_capture_config(struct solo_dev *solo_dev)
 {
 	int i, j;
 	unsigned long height;

@@ -115,7 +115,7 @@ static void solo_capture_config(struct solo6010_dev *solo_dev)
 
 int solo_osd_print(struct solo_enc_dev *solo_enc)
 {
-	struct solo6010_dev *solo_dev = solo_enc->solo_dev;
+	struct solo_dev *solo_dev = solo_enc->solo_dev;
 	char *str = solo_enc->osd_text;
 	u8 *buf;
 	u32 reg = solo_reg_read(solo_dev, SOLO_VE_OSD_CH);

@@ -151,7 +151,7 @@ int solo_osd_print(struct solo_enc_dev *solo_enc)
 	return 0;
 }
 
-static void solo_jpeg_config(struct solo6010_dev *solo_dev)
+static void solo_jpeg_config(struct solo_dev *solo_dev)
 {
 	u32 reg;
 	if (solo_dev->flags & FLAGS_6110)

@@ -169,7 +169,7 @@ static void solo_jpeg_config(struct solo6010_dev *solo_dev)
 	solo_reg_write(solo_dev, 0x0688, (0 << 16) | (30 << 8) | 60);
 }
 
-static void solo_mp4e_config(struct solo6010_dev *solo_dev)
+static void solo_mp4e_config(struct solo_dev *solo_dev)
 {
 	int i;
 	u32 reg;

@@ -206,7 +206,7 @@ static void solo_mp4e_config(struct solo6010_dev *solo_dev)
 		solo_reg_write(solo_dev, 0x0634, 0x00040008); /* ? */
 }
 
-int solo_enc_init(struct solo6010_dev *solo_dev)
+int solo_enc_init(struct solo_dev *solo_dev)
 {
 	int i;
 

@@ -219,16 +219,16 @@ int solo_enc_init(struct solo6010_dev *solo_dev)
 		solo_reg_write(solo_dev, SOLO_CAP_CH_COMP_ENA_E(i), 0);
 	}
 
-	solo6010_irq_on(solo_dev, SOLO_IRQ_ENCODER);
+	solo_irq_on(solo_dev, SOLO_IRQ_ENCODER);
 
 	return 0;
 }
 
-void solo_enc_exit(struct solo6010_dev *solo_dev)
+void solo_enc_exit(struct solo_dev *solo_dev)
 {
 	int i;
 
-	solo6010_irq_off(solo_dev, SOLO_IRQ_ENCODER);
+	solo_irq_off(solo_dev, SOLO_IRQ_ENCODER);
 
 	for (i = 0; i < solo_dev->nr_chans; i++) {
 		solo_reg_write(solo_dev, SOLO_CAP_CH_SCALE(i), 0);

136 lines not on this page · raw message

index efd88ba..0925e6f 100644
@@ -22,7 +22,7 @@
 #include <asm/uaccess.h>
 #include "solo6x10.h"
 
-static void solo_gpio_mode(struct solo6010_dev *solo_dev,
+static void solo_gpio_mode(struct solo_dev *solo_dev,
 			   unsigned int port_mask, unsigned int mode)
 {
 	int port;

@@ -57,19 +57,19 @@ static void solo_gpio_mode(struct solo6010_dev *solo_dev,
 	solo_reg_write(solo_dev, SOLO_GPIO_CONFIG_1, ret);
 }
 
-static void solo_gpio_set(struct solo6010_dev *solo_dev, unsigned int value)
+static void solo_gpio_set(struct solo_dev *solo_dev, unsigned int value)
 {
 	solo_reg_write(solo_dev, SOLO_GPIO_DATA_OUT,
 		       solo_reg_read(solo_dev, SOLO_GPIO_DATA_OUT) | value);
 }
 
-static void solo_gpio_clear(struct solo6010_dev *solo_dev, unsigned int value)
+static void solo_gpio_clear(struct solo_dev *solo_dev, unsigned int value)
 {
 	solo_reg_write(solo_dev, SOLO_GPIO_DATA_OUT,
 		       solo_reg_read(solo_dev, SOLO_GPIO_DATA_OUT) & ~value);
 }
 
-static void solo_gpio_config(struct solo6010_dev *solo_dev)
+static void solo_gpio_config(struct solo_dev *solo_dev)
 {
 	/* Video reset */
 	solo_gpio_mode(solo_dev, 0x30, 1);

@@ -89,13 +89,13 @@ static void solo_gpio_config(struct solo6010_dev *solo_dev)
 	solo_gpio_clear(solo_dev, 0xff00);
 }
 
-int solo_gpio_init(struct solo6010_dev *solo_dev)
+int solo_gpio_init(struct solo_dev *solo_dev)
 {
 	solo_gpio_config(solo_dev);
 	return 0;
 }
 
-void solo_gpio_exit(struct solo6010_dev *solo_dev)
+void solo_gpio_exit(struct solo_dev *solo_dev)
 {
 	solo_gpio_clear(solo_dev, 0x30);
 	solo_gpio_config(solo_dev);

index fba4247..ef95a50 100644
@@ -17,7 +17,7 @@
  * Foundation, Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA.
  */
 
-/* XXX: The SOLO6010 i2c does not have separate interrupts for each i2c
+/* XXX: The SOLO6x10 i2c does not have separate interrupts for each i2c
  * channel. The bus can only handle one i2c event at a time. The below handles
  * this all wrong. We should be using the status registers to see if the bus
  * is in use, and have a global lock to check the status register. Also,

@@ -28,7 +28,7 @@
 #include <linux/kernel.h>
 #include "solo6x10.h"
 
-u8 solo_i2c_readbyte(struct solo6010_dev *solo_dev, int id, u8 addr, u8 off)
+u8 solo_i2c_readbyte(struct solo_dev *solo_dev, int id, u8 addr, u8 off)
 {
 	struct i2c_msg msgs[2];
 	u8 data;

@@ -48,7 +48,7 @@ u8 solo_i2c_readbyte(struct solo6010_dev *solo_dev, int id, u8 addr, u8 off)
 	return data;
 }
 
-void solo_i2c_writebyte(struct solo6010_dev *solo_dev, int id, u8 addr,
+void solo_i2c_writebyte(struct solo_dev *solo_dev, int id, u8 addr,
 			u8 off, u8 data)
 {
 	struct i2c_msg msgs;

@@ -64,7 +64,7 @@ void solo_i2c_writebyte(struct solo6010_dev *solo_dev, int id, u8 addr,
 	i2c_transfer(&solo_dev->i2c_adap[id], &msgs, 1);
 }
 
-static void solo_i2c_flush(struct solo6010_dev *solo_dev, int wr)
+static void solo_i2c_flush(struct solo_dev *solo_dev, int wr)
 {
 	u32 ctrl;
 

@@ -87,7 +87,7 @@ static void solo_i2c_flush(struct solo6010_dev *solo_dev, int wr)
 	solo_reg_write(solo_dev, SOLO_IIC_CTRL, ctrl);
 }
 
-static void solo_i2c_start(struct solo6010_dev *solo_dev)
+static void solo_i2c_start(struct solo_dev *solo_dev)
 {
 	u32 addr = solo_dev->i2c_msg->addr << 1;
 

@@ -99,15 +99,15 @@ static void solo_i2c_start(struct solo6010_dev *solo_dev)
 	solo_i2c_flush(solo_dev, 1);
 }
 
-static void solo_i2c_stop(struct solo6010_dev *solo_dev)
+static void solo_i2c_stop(struct solo_dev *solo_dev)
 {
-	solo6010_irq_off(solo_dev, SOLO_IRQ_IIC);
+	solo_irq_off(solo_dev, SOLO_IRQ_IIC);
 	solo_reg_write(solo_dev, SOLO_IIC_CTRL, 0);
 	solo_dev->i2c_state = IIC_STATE_STOP;
 	wake_up(&solo_dev->i2c_wait);
 }
 
-static int solo_i2c_handle_read(struct solo6010_dev *solo_dev)
+static int solo_i2c_handle_read(struct solo_dev *solo_dev)
 {
 prepare_read:
 	if (solo_dev->i2c_msg_ptr != solo_dev->i2c_msg->len) {

@@ -136,7 +136,7 @@ prepare_read:
 	return 0;
 }
 
-static int solo_i2c_handle_write(struct solo6010_dev *solo_dev)
+static int solo_i2c_handle_write(struct solo_dev *solo_dev)
 {
 retry_write:
 	if (solo_dev->i2c_msg_ptr != solo_dev->i2c_msg->len) {

@@ -168,7 +168,7 @@ retry_write:
 	return 0;
 }
 
-int solo_i2c_isr(struct solo6010_dev *solo_dev)
+int solo_i2c_isr(struct solo_dev *solo_dev)
 {
 	u32 status = solo_reg_read(solo_dev, SOLO_IIC_CTRL);
 	int ret = -EINVAL;

@@ -212,7 +212,7 @@ int solo_i2c_isr(struct solo6010_dev *solo_dev)
 static int solo_i2c_master_xfer(struct i2c_adapter *adap,
 				struct i2c_msg msgs[], int num)
 {
-	struct solo6010_dev *solo_dev = adap->algo_data;
+	struct solo_dev *solo_dev = adap->algo_data;
 	unsigned long timeout;
 	int ret;
 	int i;

@@ -233,7 +233,7 @@ static int solo_i2c_master_xfer(struct i2c_adapter *adap,
 	solo_dev->i2c_msg_ptr = 0;
 
 	solo_reg_write(solo_dev, SOLO_IIC_CTRL, 0);
-	solo6010_irq_on(solo_dev, SOLO_IRQ_IIC);
+	solo_irq_on(solo_dev, SOLO_IRQ_IIC);
 	solo_i2c_start(solo_dev);
 
 	timeout = HZ / 2;

@@ -272,7 +272,7 @@ static struct i2c_algorithm solo_i2c_algo = {
 	.functionality	= solo_i2c_functionality,
 };
 
-int solo_i2c_init(struct solo6010_dev *solo_dev)
+int solo_i2c_init(struct solo_dev *solo_dev)
 {
 	int i;
 	int ret;

@@ -288,8 +288,7 @@ int solo_i2c_init(struct solo6010_dev *solo_dev)
 	for (i = 0; i < SOLO_I2C_ADAPTERS; i++) {
 		struct i2c_adapter *adap = &solo_dev->i2c_adap[i];
 
-		snprintf(adap->name, I2C_NAME_SIZE, "%s I2C %d",
-			 SOLO6010_NAME, i);
+		snprintf(adap->name, I2C_NAME_SIZE, "%s I2C %d", SOLO6X10_NAME, i);
 		adap->algo = &solo_i2c_algo;
 		adap->algo_data = solo_dev;
 		adap->retries = 1;

@@ -318,7 +317,7 @@ int solo_i2c_init(struct solo6010_dev *solo_dev)
 	return 0;
 }
 
-void solo_i2c_exit(struct solo6010_dev *solo_dev)
+void solo_i2c_exit(struct solo_dev *solo_dev)
 {
 	int i;
 

index fb0507e..50defec 100644
@@ -17,8 +17,8 @@
  * Foundation, Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA.
  */
 
-#ifndef __SOLO6010_JPEG_H
-#define __SOLO6010_JPEG_H
+#ifndef __SOLO6X10_JPEG_H
+#define __SOLO6X10_JPEG_H
 
 static unsigned char jpeg_header[] = {
 	0xff, 0xd8, 0xff, 0xfe, 0x00, 0x0d, 0x42, 0x6c,

@@ -102,4 +102,4 @@ static unsigned char jpeg_header[] = {
 /* This is the byte marker for the start of SOF0: 0xffc0 marker */
 #define SOF0_START	575
 
-#endif /* __SOLO6010_JPEG_H */
+#endif /* __SOLO6X10_JPEG_H */

index b176003..3d7e569 100644
@@ -17,8 +17,8 @@
  * Foundation, Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA.
  */
 
-#ifndef __SOLO6010_OFFSETS_H
-#define __SOLO6010_OFFSETS_H
+#ifndef __SOLO6X10_OFFSETS_H
+#define __SOLO6X10_OFFSETS_H
 
 /* Offsets and sizes of the external address */
 #define SOLO_DISP_EXT_ADDR			0x00000000

@@ -71,4 +71,4 @@
 		 (SOLO_MP4D_EXT_SIZE * __solo->nr_chans))
 #define SOLO_JPEG_EXT_SIZE(__solo)		(0x00080000 * __solo->nr_chans)
 
-#endif /* __SOLO6010_OFFSETS_H */
+#endif /* __SOLO6X10_OFFSETS_H */

index d72efbb..591e0e8 100644
@@ -17,8 +17,8 @@
  * Foundation, Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA.
  */
 
-#ifndef __SOLO6010_OSD_FONT_H
-#define __SOLO6010_OSD_FONT_H
+#ifndef __SOLO6X10_OSD_FONT_H
+#define __SOLO6X10_OSD_FONT_H
 
 static const unsigned int solo_osd_font[] = {
 	0x00000000, 0x0000c0c8, 0xccfefe0c, 0x08000000,

@@ -151,4 +151,4 @@ static const unsigned int solo_osd_font[] = {
 	0x00000000, 0x0010386c, 0xc6c6fe00, 0x00000000
 };
 
-#endif /* __SOLO6010_OSD_FONT_H */
+#endif /* __SOLO6X10_OSD_FONT_H */

index 1b88d10..5717eab 100644
@@ -23,7 +23,7 @@
 
 /* #define SOLO_TEST_P2M */
 
-int solo_p2m_dma(struct solo6010_dev *solo_dev, u8 id, int wr,
+int solo_p2m_dma(struct solo_dev *solo_dev, u8 id, int wr,
 		 void *sys_addr, u32 ext_addr, u32 size)
 {
 	dma_addr_t dma_addr;

@@ -46,7 +46,7 @@ int solo_p2m_dma(struct solo6010_dev *solo_dev, u8 id, int wr,
 	return ret;
 }
 
-int solo_p2m_dma_t(struct solo6010_dev *solo_dev, u8 id, int wr,
+int solo_p2m_dma_t(struct solo_dev *solo_dev, u8 id, int wr,
 		   dma_addr_t dma_addr, u32 ext_addr, u32 size)
 {
 	struct p2m_desc *desc = kzalloc(sizeof(*desc) * 2, GFP_DMA);

@@ -80,7 +80,7 @@ void solo_p2m_push_desc(struct p2m_desc *desc, int wr, dma_addr_t dma_addr,
 	}
 }
 
-int solo_p2m_dma_desc(struct solo6010_dev *solo_dev, u8 id,
+int solo_p2m_dma_desc(struct solo_dev *solo_dev, u8 id,
 		      struct p2m_desc *desc, int desc_count)
 {
 	struct solo_p2m_dev *p2m_dev;

@@ -136,7 +136,7 @@ int solo_p2m_dma_desc(struct solo6010_dev *solo_dev, u8 id,
 	return ret;
 }
 
-int solo_p2m_dma_sg(struct solo6010_dev *solo_dev, u8 id,
+int solo_p2m_dma_sg(struct solo_dev *solo_dev, u8 id,
 		    struct p2m_desc *pdesc, int wr,
 		    struct scatterlist *sg, u32 sg_off,
 		    u32 ext_addr, u32 size)

@@ -185,7 +185,7 @@ int solo_p2m_dma_sg(struct solo6010_dev *solo_dev, u8 id,
 
 #define P2M_TEST_CHAR		0xbe
 
-static unsigned long long p2m_test(struct solo6010_dev *solo_dev, u8 id,
+static unsigned long long p2m_test(struct solo_dev *solo_dev, u8 id,
 				   u32 base, int size)
 {
 	u8 *wr_buf;

@@ -195,13 +195,13 @@ static unsigned long long p2m_test(struct solo6010_dev *solo_dev, u8 id,
 
 	wr_buf = kmalloc(size, GFP_KERNEL);
 	if (!wr_buf) {
-		printk(SOLO6010_NAME ": Failed to malloc for p2m_test\n");
+		printk(SOLO6X10_NAME ": Failed to malloc for p2m_test\n");
 		return size;
 	}
 
 	rd_buf = kmalloc(size, GFP_KERNEL);
 	if (!rd_buf) {
-		printk(SOLO6010_NAME ": Failed to malloc for p2m_test\n");
+		printk(SOLO6X10_NAME ": Failed to malloc for p2m_test\n");
 		kfree(wr_buf);
 		return size;
 	}

@@ -224,21 +224,21 @@ static unsigned long long p2m_test(struct solo6010_dev *solo_dev, u8 id,
 
 #define TEST_CHUNK_SIZE		(8 * 1024)
 
-static void run_p2m_test(struct solo6010_dev *solo_dev)
+static void run_p2m_test(struct solo_dev *solo_dev)
 {
 	unsigned long long errs = 0;
 	u32 size = SOLO_JPEG_EXT_ADDR(solo_dev) + SOLO_JPEG_EXT_SIZE(solo_dev);
 	int i, d;
 
 	printk(KERN_WARNING "%s: Testing %u bytes of external ram\n",
-	       SOLO6010_NAME, size);
+	       SOLO6X10_NAME, size);
 
 	for (i = 0; i < size; i += TEST_CHUNK_SIZE)
 		for (d = 0; d < 4; d++)
 			errs += p2m_test(solo_dev, d, i, TEST_CHUNK_SIZE);
 
 	printk(KERN_WARNING "%s: Found %llu errors during p2m test\n",
-	       SOLO6010_NAME, errs);
+	       SOLO6X10_NAME, errs);
 
 	return;
 }

@@ -246,7 +246,7 @@ static void run_p2m_test(struct solo6010_dev *solo_dev)
 #define run_p2m_test(__solo)	do {} while (0)
 #endif
 
-void solo_p2m_isr(struct solo6010_dev *solo_dev, int id)
+void solo_p2m_isr(struct solo_dev *solo_dev, int id)
 {
 	struct solo_p2m_dev *p2m_dev = &solo_dev->p2m_dev[id];
 

@@ -255,7 +255,7 @@ void solo_p2m_isr(struct solo6010_dev *solo_dev, int id)
 	complete(&p2m_dev->completion);
 }
 
-void solo_p2m_error_isr(struct solo6010_dev *solo_dev, u32 status)
+void solo_p2m_error_isr(struct solo_dev *solo_dev, u32 status)
 {
 	struct solo_p2m_dev *p2m_dev;
 	int i;

@@ -271,15 +271,15 @@ void solo_p2m_error_isr(struct solo6010_dev *solo_dev, u32 status)
 	}
 }
 
-void solo_p2m_exit(struct solo6010_dev *solo_dev)
+void solo_p2m_exit(struct solo_dev *solo_dev)
 {
 	int i;
 
 	for (i = 0; i < SOLO_NR_P2M; i++)
-		solo6010_irq_off(solo_dev, SOLO_IRQ_P2M(i));
+		solo_irq_off(solo_dev, SOLO_IRQ_P2M(i));
 }
 
-int solo_p2m_init(struct solo6010_dev *solo_dev)
+int solo_p2m_init(struct solo_dev *solo_dev)
 {
 	struct solo_p2m_dev *p2m_dev;
 	int i;

@@ -296,7 +296,7 @@ int solo_p2m_init(struct solo6010_dev *solo_dev)
 			       SOLO_P2M_DMA_INTERVAL(3) |
 			       SOLO_P2M_DESC_INTR_OPT |
 			       SOLO_P2M_PCI_MASTER_MODE);
-		solo6010_irq_on(solo_dev, SOLO_IRQ_P2M(i));
+		solo_irq_on(solo_dev, SOLO_IRQ_P2M(i));
 	}
 
 	run_p2m_test(solo_dev);

index edf77e8..aca5444 100644
@@ -17,12 +17,12 @@
  * Foundation, Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA.
  */
 
-#ifndef __SOLO6010_REGISTERS_H
-#define __SOLO6010_REGISTERS_H
+#ifndef __SOLO6X10_REGISTERS_H
+#define __SOLO6X10_REGISTERS_H
 
 #include "offsets.h"
 
-/* Global 6010 system configuration */
+/* Global 6X10 system configuration */
 #define SOLO_SYS_CFG				0x0000
 #define   SOLO6010_SYS_CFG_FOUT_EN		0x00000001 /* 6010 only */
 #define   SOLO6010_SYS_CFG_PLL_BYPASS		0x00000002 /* 6010 only */

@@ -634,4 +634,4 @@
 #define WATCHDOG_STAT(status)			(status<<8)
 #define WATCHDOG_TIME(sec)			(sec&0xff)
 
-#endif /* __SOLO6010_REGISTERS_H */
+#endif /* __SOLO6X10_REGISTERS_H */

175 lines not on this page · raw message

index 0f3d1e4..db56b42 100644
@@ -140,7 +140,7 @@ static u8 tbl_tw2865_pal_template[] = {
 
 #define is_tw286x(__solo, __id) (!(__solo->tw2815 & (1 << __id)))
 
-static u8 tw_readbyte(struct solo6010_dev *solo_dev, int chip_id, u8 tw6x_off,
+static u8 tw_readbyte(struct solo_dev *solo_dev, int chip_id, u8 tw6x_off,
 		      u8 tw_off)
 {
 	if (is_tw286x(solo_dev, chip_id))

@@ -153,7 +153,7 @@ static u8 tw_readbyte(struct solo6010_dev *solo_dev, int chip_id, u8 tw6x_off,
 					 tw_off);
 }
 
-static void tw_writebyte(struct solo6010_dev *solo_dev, int chip_id,
+static void tw_writebyte(struct solo_dev *solo_dev, int chip_id,
 			 u8 tw6x_off, u8 tw_off, u8 val)
 {
 	if (is_tw286x(solo_dev, chip_id))

@@ -166,7 +166,7 @@ static void tw_writebyte(struct solo6010_dev *solo_dev, int chip_id,
 				   tw_off, val);
 }
 
-static void tw_write_and_verify(struct solo6010_dev *solo_dev, u8 addr, u8 off,
+static void tw_write_and_verify(struct solo_dev *solo_dev, u8 addr, u8 off,
 				u8 val)
 {
 	int i;

@@ -180,11 +180,11 @@ static void tw_write_and_verify(struct solo6010_dev *solo_dev, u8 addr, u8 off,
 		msleep_interruptible(1);
 	}
 
-/*	printk("solo6010/tw28: Error writing register: %02x->%02x [%02x]\n",
+/*	printk("solo6x10/tw28: Error writing register: %02x->%02x [%02x]\n",
 		addr, off, val); */
 }
 
-static int tw2865_setup(struct solo6010_dev *solo_dev, u8 dev_addr)
+static int tw2865_setup(struct solo_dev *solo_dev, u8 dev_addr)
 {
 	u8 tbl_tw2865_common[256];
 	int i;

@@ -234,7 +234,7 @@ static int tw2865_setup(struct solo6010_dev *solo_dev, u8 dev_addr)
 	return 0;
 }
 
-static int tw2864_setup(struct solo6010_dev *solo_dev, u8 dev_addr)
+static int tw2864_setup(struct solo_dev *solo_dev, u8 dev_addr)
 {
 	u8 tbl_tw2864_common[sizeof(tbl_tw2864_template)];
 	int i;

@@ -320,7 +320,7 @@ static int tw2864_setup(struct solo6010_dev *solo_dev, u8 dev_addr)
 	return 0;
 }
 
-static int tw2815_setup(struct solo6010_dev *solo_dev, u8 dev_addr)
+static int tw2815_setup(struct solo_dev *solo_dev, u8 dev_addr)
 {
 	u8 tbl_ntsc_tw2815_common[] = {
 		0x00, 0xc8, 0x20, 0xd0, 0x06, 0xf0, 0x08, 0x80,

@@ -481,7 +481,7 @@ static int tw2815_setup(struct solo6010_dev *solo_dev, u8 dev_addr)
 #define FIRST_ACTIVE_LINE	0x0008
 #define LAST_ACTIVE_LINE	0x0102
 
-static void saa7128_setup(struct solo6010_dev *solo_dev)
+static void saa7128_setup(struct solo_dev *solo_dev)
 {
 	int i;
 	unsigned char regs[128] = {

@@ -539,7 +539,7 @@ static void saa7128_setup(struct solo6010_dev *solo_dev)
 	return;
 }
 
-int solo_tw28_init(struct solo6010_dev *solo_dev)
+int solo_tw28_init(struct solo_dev *solo_dev)
 {
 	int i;
 	u8 value;

@@ -602,7 +602,7 @@ int solo_tw28_init(struct solo6010_dev *solo_dev)
  * (address 0x012C) of the SOLO6010 chip doesn't give the correct video
  * status signal values.
  */
-int tw28_get_video_status(struct solo6010_dev *solo_dev, u8 ch)
+int tw28_get_video_status(struct solo_dev *solo_dev, u8 ch)
 {
 	u8 val, chip_num;
 

@@ -619,7 +619,7 @@ int tw28_get_video_status(struct solo6010_dev *solo_dev, u8 ch)
 #if 0
 /* Status of audio from up to 4 techwell chips are combined into 1 variable.
  * See techwell datasheet for details. */
-u16 tw28_get_audio_status(struct solo6010_dev *solo_dev)
+u16 tw28_get_audio_status(struct solo_dev *solo_dev)
 {
 	u8 val;
 	u16 status = 0;

@@ -635,8 +635,7 @@ u16 tw28_get_audio_status(struct solo6010_dev *solo_dev)
 }
 #endif
 
-int tw28_set_ctrl_val(struct solo6010_dev *solo_dev, u32 ctrl, u8 ch,
-		      s32 val)
+int tw28_set_ctrl_val(struct solo_dev *solo_dev, u32 ctrl, u8 ch, s32 val)
 {
 	char sval;
 	u8 chip_num;

@@ -708,7 +707,7 @@ int tw28_set_ctrl_val(struct solo6010_dev *solo_dev, u32 ctrl, u8 ch,
 	return 0;
 }
 
-int tw28_get_ctrl_val(struct solo6010_dev *solo_dev, u32 ctrl, u8 ch,
+int tw28_get_ctrl_val(struct solo_dev *solo_dev, u32 ctrl, u8 ch,
 		      s32 *val)
 {
 	u8 rval, chip_num;

@@ -768,7 +767,7 @@ int tw28_get_ctrl_val(struct solo6010_dev *solo_dev, u32 ctrl, u8 ch,
  * don't need to offset TW_CHIP_OFFSET_ADDR. The TW_CHIP_OFFSET_ADDR used
  * is the base address of the techwell chip.
  */
-void tw2815_Set_AudioOutVol(struct solo6010_dev *solo_dev, unsigned int u_val)
+void tw2815_Set_AudioOutVol(struct solo_dev *solo_dev, unsigned int u_val)
 {
 	unsigned int val;
 	unsigned int chip_num;

@@ -785,7 +784,7 @@ void tw2815_Set_AudioOutVol(struct solo6010_dev *solo_dev, unsigned int u_val)
 }
 #endif
 
-u8 tw28_get_audio_gain(struct solo6010_dev *solo_dev, u8 ch)
+u8 tw28_get_audio_gain(struct solo_dev *solo_dev, u8 ch)
 {
 	u8 val;
 	u8 chip_num;

@@ -801,7 +800,7 @@ u8 tw28_get_audio_gain(struct solo6010_dev *solo_dev, u8 ch)
 	return (ch % 2) ? (val >> 4) : (val & 0x0f);
 }
 
-void tw28_set_audio_gain(struct solo6010_dev *solo_dev, u8 ch, u8 val)
+void tw28_set_audio_gain(struct solo_dev *solo_dev, u8 ch, u8 val)
 {
 	u8 old_val;
 	u8 chip_num;

index 4862ac9..a44a03a 100644
@@ -17,8 +17,8 @@
  * Foundation, Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA.
  */
 
-#ifndef __SOLO6010_TW28_H
-#define __SOLO6010_TW28_H
+#ifndef __SOLO6X10_TW28_H
+#define __SOLO6X10_TW28_H
 
 #include "solo6x10.h"
 

@@ -46,20 +46,18 @@
 #define TW286x_AUDIO_OUTPUT_VOL_ADDR		0xdf
 #define TW286x_AUDIO_INPUT_GAIN_ADDR(n)		(0xD0 + ((n > 1) ? 1 : 0))
 
-int solo_tw28_init(struct solo6010_dev *solo_dev);
+int solo_tw28_init(struct solo_dev *solo_dev);
 
-int tw28_set_ctrl_val(struct solo6010_dev *solo_dev, u32 ctrl, u8 ch,
-		      s32 val);
-int tw28_get_ctrl_val(struct solo6010_dev *solo_dev, u32 ctrl, u8 ch,
-		      s32 *val);
+int tw28_set_ctrl_val(struct solo_dev *solo_dev, u32 ctrl, u8 ch, s32 val);
+int tw28_get_ctrl_val(struct solo_dev *solo_dev, u32 ctrl, u8 ch, s32 *val);
 
-u8 tw28_get_audio_gain(struct solo6010_dev *solo_dev, u8 ch);
-void tw28_set_audio_gain(struct solo6010_dev *solo_dev, u8 ch, u8 val);
-int tw28_get_video_status(struct solo6010_dev *solo_dev, u8 ch);
+u8 tw28_get_audio_gain(struct solo_dev *solo_dev, u8 ch);
+void tw28_set_audio_gain(struct solo_dev *solo_dev, u8 ch, u8 val);
+int tw28_get_video_status(struct solo_dev *solo_dev, u8 ch);
 
 #if 0
-unsigned int tw2815_get_audio_status(struct SOLO6010 *solo6010);
-void tw2815_Set_AudioOutVol(struct SOLO6010 *solo6010, unsigned int u_val);
+unsigned int tw2815_get_audio_status(struct SOLO *solo);
+void tw2815_Set_AudioOutVol(struct SOLO *solo, unsigned int u_val);
 #endif
 
-#endif /* __SOLO6010_TW28_H */
+#endif /* __SOLO6X10_TW28_H */

314 lines not on this page · raw message

233 lines not on this page · raw message