Skip to contentSkip to conversation

omap: Use a memory address for storing the debug port info instead of UART1

PATCH New Tony Lindgren 1 participant 1 message May 1, 2010

Subsystems (4)
lore
Share & tools
lore

Tony Lindgren

author maintainer
#0 lore raw

PATCH 1/1 omap: Use a memory address for storing the debug port info instead of UART1

This removes the dependency to the UART1 being
available for storing the debug configuration in
uncompress.h.

As suggested by Cyril Chemparathy <[email protected]>,
Vikram Pandita <[email protected]> and
Kevin Hilman <[email protected]>.

arch/arm/mach-omap1/include/mach/debug-macro.S +6 -15
index b6d9584..e8a8cf3 100644
@@ -13,6 +13,8 @@
 
 #include <linux/serial_reg.h>
 
+#include <asm/memory.h>
+
 #include <plat/serial.h>
 
 		.pushsection .data
@@ -37,23 +39,12 @@ omap_uart_virt:	.word	0x0
 		cmp	\rx, #0			@ is port configured?
 		bne	99f			@ already configured
 
-		/* Check 7XX UART1 scratchpad register for uart to use */
+		/* Check the debug UART configuration set in uncompress.h */
 		mrc	p15, 0, \rx, c1, c0
 		tst	\rx, #1			@ MMU enabled?
-		moveq	\rx, #0xff000000	@ physical base address
-		movne	\rx, #0xfe000000	@ virtual base
-		orr	\rx, \rx, #0x00fb0000	@ OMAP1UART1
-		ldrb	\rx, [\rx, #(UART_SCR << OMAP7XX_PORT_SHIFT)]
-		cmp	\rx, #0			@ anything in 7XX scratchpad?
-		bne	10f			@ found 7XX uart
-
-		/* Check 15xx/16xx UART1 scratchpad register for uart to use */
-		mrc	p15, 0, \rx, c1, c0
-		tst	\rx, #1			@ MMU enabled?
-		moveq	\rx, #0xff000000	@ physical base address
-		movne	\rx, #0xfe000000	@ virtual base
-		orr	\rx, \rx, #0x00fb0000	@ OMAP1UART1
-		ldrb	\rx, [\rx, #(UART_SCR << OMAP_PORT_SHIFT)]
+		ldreq	\rx, =OMAP_UART_INFO
+		ldrne	\rx, =__phys_to_virt(OMAP_UART_INFO)
+		ldr	\rx, [\rx, #0]
 
 		/* Select the UART to use based on the UART1 scratchpad value */
 10:		cmp	\rx, #0			@ no port configured?
arch/arm/mach-omap2/include/mach/debug-macro.S +6 -5
index 4a63a2e..4976169 100644
@@ -13,6 +13,8 @@
 
 #include <linux/serial_reg.h>
 
+#include <asm/memory.h>
+
 #include <plat/serial.h>
 
 #define UART_OFFSET(addr)	((addr) & 0x00ffffff)
@@ -40,13 +42,12 @@ omap_uart_lsr:	.word	0
 		cmp	\rx, #0			@ is port configured?
 		bne	99f			@ already configured
 
-		/* Check UART1 scratchpad register for uart to use */
+		/* Check the debug UART configuration set in uncompress.h */
 		mrc	p15, 0, \rx, c1, c0
 		tst	\rx, #1			@ MMU enabled?
-		moveq	\rx, #0x48000000	@ physical base address
-		movne	\rx, #0xfa000000	@ virtual base
-		orr	\rx, \rx, #0x0006a000	@ uart1 on omap2/3/4
-		ldrb	\rx, [\rx, #(UART_SCR << OMAP_PORT_SHIFT)] @ scratchpad
+		ldreq	\rx, =OMAP_UART_INFO
+		ldrne	\rx, =__phys_to_virt(OMAP_UART_INFO)
+		ldr	\rx, [\rx, #0]
 
 		/* Select the UART to use based on the UART1 scratchpad value */
 		cmp	\rx, #0			@ no port configured?
arch/arm/plat-omap/include/plat/serial.h +2 -0
index 83dce4c..20c27b9 100644
@@ -15,6 +15,8 @@
 
 #include <linux/init.h>
 
+#define OMAP_UART_INFO		(PHYS_OFFSET + 0x3ff8)
+
 /* OMAP1 serial ports */
 #define OMAP1_UART1_BASE	0xfffb0000
 #define OMAP1_UART2_BASE	0xfffb0800
arch/arm/plat-omap/include/plat/uncompress.h +18 -27

87 lines not on this page · raw message

--H8ygTp4AXg6deix2--