add bcmring mtd nand driver support
PATCH 1/1 add bcmring mtd nand driver support
Add mtd umi driver for bcmring arm arch.
Add header files, register definition files,
add entry in Kconfig and Makefile.
Signed-off-by Leo Hao Chen <[email protected]>
--- arch/arm/mach-bcmring/include/mach/reg_nand.h | 66 ++ arch/arm/mach-bcmring/include/mach/reg_umi.h | 237 ++++++++ drivers/mtd/nand/Kconfig | 16 + drivers/mtd/nand/Makefile | 1 + drivers/mtd/nand/bcm_umi_bch.c | 213 +++++++ drivers/mtd/nand/bcm_umi_nand.c | 792 +++++++++++++++++++++++++ drivers/mtd/nand/nand_bcm_umi.c | 149 +++++ drivers/mtd/nand/nand_bcm_umi.h | 358 +++++++++++ 8 files changed, 1832 insertions(+), 0 deletions(-) create mode 100644 arch/arm/mach-bcmring/include/mach/reg_nand.h create mode 100644 arch/arm/mach-bcmring/include/mach/reg_umi.h create mode 100644 drivers/mtd/nand/bcm_umi_bch.c create mode 100644 drivers/mtd/nand/bcm_umi_nand.c create mode 100644 drivers/mtd/nand/nand_bcm_umi.c create mode 100644 drivers/mtd/nand/nand_bcm_umi.h
arch/arm/mach-bcmring/include/mach/reg_nand.h new file +66 -0
@@ -0,0 +1,66 @@ +/***************************************************************************** +* Copyright 2001 - 2008 Broadcom Corporation. All rights reserved. +* +* Unless you and Broadcom execute a separate written software license +* agreement governing use of this software, this software is licensed to you +* under the terms of the GNU General Public License version 2, available at +* http://www.broadcom.com/licenses/GPLv2.php (the "GPL"). +* +* Notwithstanding the above, under no circumstances may you combine this +* software in any way with any other Broadcom software provided under a +* license other than the GPL, without Broadcom's express prior written +* consent. +*****************************************************************************/ + +/* +* +***************************************************************************** +* +* REG_NAND.h +* +* PURPOSE: +* +* This file contains definitions for the nand registers: +* +* NOTES: +* +*****************************************************************************/ + +#if !defined(__ASM_ARCH_REG_NAND_H) +#define __ASM_ARCH_REG_NAND_H + +/* ---- Include Files ---------------------------------------------------- */ +#include <csp/reg.h> +#include <mach/reg_umi.h> + +/* ---- Constants and Types ---------------------------------------------- */ + +#define HW_NAND_BASE MM_IO_BASE_NAND/* NAND Flash */ + +/* DMA accesses by the bootstrap need hard nonvirtual addresses */ +#define REG_NAND_CMD __REG16(HW_NAND_BASE + 0) +#define REG_NAND_ADDR __REG16(HW_NAND_BASE + 4) + +#define REG_NAND_PHYS_DATA16 (HW_NAND_BASE + 8) +#define REG_NAND_PHYS_DATA8 (HW_NAND_BASE + 8) +#define REG_NAND_DATA16 __REG16(REG_NAND_PHYS_DATA16) +#define REG_NAND_DATA8 __REG8(REG_NAND_PHYS_DATA8) + +/* use appropriate offset to make sure it start at the 1K boundary */ +#define REG_NAND_PHYS_DATA_DMA (HW_NAND_BASE + 0x400) +#define REG_NAND_DATA_DMA __REG32(REG_NAND_PHYS_DATA_DMA) + +/* Linux DMA requires physical address of the data register */ +#define REG_NAND_DATA16_PADDR HW_IO_VIRT_TO_PHYS(REG_NAND_PHYS_DATA16) +#define REG_NAND_DATA8_PADDR HW_IO_VIRT_TO_PHYS(REG_NAND_PHYS_DATA8) +#define REG_NAND_DATA_PADDR HW_IO_VIRT_TO_PHYS(REG_NAND_PHYS_DATA_DMA) + +#define NAND_BUS_16BIT () (0) +#define NAND_BUS_8BIT () (!NAND_BUS_16BIT()) + +/* Register offsets */ +#define REG_NAND_CMD_OFFSET (0) +#define REG_NAND_ADDR_OFFSET (4) +#define REG_NAND_DATA8_OFFSET (8) + +#endif
arch/arm/mach-bcmring/include/mach/reg_umi.h new file +237 -0
237 lines not on this page · raw message
drivers/mtd/nand/Kconfig +16 -0
@@ -203,6 +203,22 @@ config MTD_NAND_S3C2410_CLKSTOP when the is NAND chip selected or released, but will save approximately 5mA of power when there is nothing happening. +config MTD_NAND_BCM_UMI + tristate "NAND Flash support for BCM Reference Boards" + depends on ARCH_BCMRING && MTD_NAND + help + This enables the NAND flash controller on the BCM UMI block. + + No board specfic support is done by this driver, each board + must advertise a platform_device for the driver to attach. + +config MTD_NAND_BCM_UMI_HWCS + bool "BCM UMI NAND Hardware CS" + depends on MTD_NAND_BCM_UMI + help + Enable the use of the BCM UMI block's internal CS using NAND. + This should only be used if you know the external NAND CS can toggle. + config MTD_NAND_DISKONCHIP tristate "DiskOnChip 2000, Millennium and Millennium Plus (NAND reimplementation) (EXPERIMENTAL)" depends on EXPERIMENTAL
drivers/mtd/nand/Makefile +1 -0
@@ -42,5 +42,6 @@ obj-$(CONFIG_MTD_NAND_SOCRATES) += socrates_nand.o obj-$(CONFIG_MTD_NAND_TXX9NDFMC) += txx9ndfmc.o obj-$(CONFIG_MTD_NAND_W90P910) += w90p910_nand.o obj-$(CONFIG_MTD_NAND_NOMADIK) += nomadik_nand.o +obj-$(CONFIG_MTD_NAND_BCM_UMI) += bcm_umi_nand.o nand_bcm_umi.o nand-objs := nand_base.o nand_bbt.o
drivers/mtd/nand/bcm_umi_bch.c new file +213 -0
213 lines not on this page · raw message
drivers/mtd/nand/bcm_umi_nand.c new file +792 -0
792 lines not on this page · raw message
drivers/mtd/nand/nand_bcm_umi.c new file +149 -0
149 lines not on this page · raw message
drivers/mtd/nand/nand_bcm_umi.h new file +358 -0
358 lines not on this page · raw message
Signature · 8 lines
1.6.0.6 -- Leo Hao Chen ------------------------ Life is short, run long.