Skip to contentSkip to conversation

I don't believe all this advanced routing stuff is real!

LARTC Greg Scott 3 participants 4 messages Nov 2, 2001 – Nov 12, 2001

lore
Share & tools
lore

Greg Scott

author
#0 lore raw

I'll bet somebody, somewhere knows how answer this. I am running Red Hat Linux v7.1, which is based on kernel 2.4.2-2.

I went to this URL:

http://ds9a.nl/2.4Routing/HOWTO/cvs/2.4routing/output/2.4routing-5.html

As I understand things, this is the more or less official HOWTO for the advanced routing stuff.

Well - how come none of it works???

In particular, the section about GRE tunneling gives some very specific directions about the commands needed to set all of it up. Here is a direct quote:

Let's say you have 3 networks: Internal networks A and B, and intermediate network C (or let's say, Internet).
So we have network A:

	network 10.0.1.0
	netmask 255.255.255.0
	router  10.0.1.1
The router has address 172.16.17.18 on network C. Let's call this network
neta (ok, hardly original) 
and network B: 
	network 10.0.2.0
	netmask 255.255.255.0
	router  10.0.2.1

The router has address 172.19.20.21 on network C. Let's call this network netb (still not original)
As far as network C is concerned, we assume that it will pass any packet sent from A to B and vice versa. How and why, we do not care. On the router of network A, you do the following:

	ip tunnel add netb mode gre remote 172.19.20.21 local 172.16.17.18
ttl 255
	ip link set netb up
	ip addr add 10.0.1.1 dev netb
	ip route add 10.0.2.0/24 dev netb

Ok, wonderful. I did that and here is the result:

# /sbin/ip tunnel add netb mode gre remote nnn.qqq.228.33 local
xxx.yyy.172.162 ttl 255
ioctl: No such device

Huh? What's going on here? So I tried a couple other experiments:

# /sbin/ip tunnel add netb
cannot determine tunnel mode (ipip, gre or sit)

Fair enough. Let's add some more:

# /sbin/ip tunnel add netb mode gre
ioctl: No such device

Now I'm really confused. Maybe the online help gives me a clue:

# /sbin/ip help 
Usage: ip [ OPTIONS ] OBJECT { COMMAND | help }
where  OBJECT := { link | addr | route | rule | neigh | tunnel |
                   maddr | mroute | monitor }
       OPTIONS := { -V[ersion] | -s[tatistics] | -r[esolve] |
                    -f[amily] { inet | inet6 | ipx | dnet | link } |
-o[neline]}

So let's try a few things:

# /sbin/ip -V
ip utility, iproute2-ss000305

This seemed to work as advertised.

# /sbin/ip -s
Usage: ip [ OPTIONS ] OBJECT { COMMAND | help }
where  OBJECT := { link | addr | route | rule | neigh | tunnel |
                   maddr | mroute | monitor }
       OPTIONS := { -V[ersion] | -s[tatistics] | -r[esolve] |
                    -f[amily] { inet | inet6 | ipx | dnet | link } |
-o[neline]}
# /sbin/ip -r
Usage: ip [ OPTIONS ] OBJECT { COMMAND | help }
where  OBJECT := { link | addr | route | rule | neigh | tunnel |
                   maddr | mroute | monitor }
       OPTIONS := { -V[ersion] | -s[tatistics] | -r[esolve] |
                    -f[amily] { inet | inet6 | ipx | dnet | link } |
-o[neline]}

So -V does what the online help says it does, but -s and -r generate some kind of syntax error.

What am I missing? Should I be modprobing some module someplace? If so, what? How do I tell what modules are available and what they do? Or is all this advanced routing stuff not ready for use yet?

- Greg Scott

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/2.4Routing/

author
#1 lore raw

RE: [LARTC] I don't believe all this advanced routing stuff is re

I'm an idiot!

modprobe ip_gre

does the trick.

- Greg Scott

-----Original Message-----
From: Greg Scott [mailto:[email protected]]
Sent: Thursday, November 01, 2001 10:18 PM
To: [email protected]
Subject: [LARTC] I don't believe all this advanced routing stuff is real!

I'll bet somebody, somewhere knows how answer this. I am running Red Hat Linux v7.1, which is based on kernel 2.4.2-2.

I went to this URL:

http://ds9a.nl/2.4Routing/HOWTO/cvs/2.4routing/output/2.4routing-5.html

As I understand things, this is the more or less official HOWTO for the advanced routing stuff.

Well - how come none of it works???

In particular, the section about GRE tunneling gives some very specific directions about the commands needed to set all of it up. Here is a direct quote:

Let's say you have 3 networks: Internal networks A and B, and intermediate network C (or let's say, Internet).
So we have network A:

	network 10.0.1.0
	netmask 255.255.255.0
	router  10.0.1.1
The router has address 172.16.17.18 on network C. Let's call this network
neta (ok, hardly original) 
and network B: 
	network 10.0.2.0
	netmask 255.255.255.0
	router  10.0.2.1

The router has address 172.19.20.21 on network C. Let's call this network netb (still not original)
As far as network C is concerned, we assume that it will pass any packet sent from A to B and vice versa. How and why, we do not care. On the router of network A, you do the following:

	ip tunnel add netb mode gre remote 172.19.20.21 local 172.16.17.18
ttl 255
	ip link set netb up
	ip addr add 10.0.1.1 dev netb
	ip route add 10.0.2.0/24 dev netb

Ok, wonderful. I did that and here is the result:

# /sbin/ip tunnel add netb mode gre remote nnn.qqq.228.33 local
xxx.yyy.172.162 ttl 255
ioctl: No such device

Huh? What's going on here? So I tried a couple other experiments:

# /sbin/ip tunnel add netb
cannot determine tunnel mode (ipip, gre or sit)

Fair enough. Let's add some more:

# /sbin/ip tunnel add netb mode gre
ioctl: No such device

Now I'm really confused. Maybe the online help gives me a clue:

# /sbin/ip help 
Usage: ip [ OPTIONS ] OBJECT { COMMAND | help }
where  OBJECT := { link | addr | route | rule | neigh | tunnel |
                   maddr | mroute | monitor }
       OPTIONS := { -V[ersion] | -s[tatistics] | -r[esolve] |
                    -f[amily] { inet | inet6 | ipx | dnet | link } |
-o[neline]}

So let's try a few things:

# /sbin/ip -V
ip utility, iproute2-ss000305

This seemed to work as advertised.

# /sbin/ip -s
Usage: ip [ OPTIONS ] OBJECT { COMMAND | help }
where  OBJECT := { link | addr | route | rule | neigh | tunnel |
                   maddr | mroute | monitor }
       OPTIONS := { -V[ersion] | -s[tatistics] | -r[esolve] |
                    -f[amily] { inet | inet6 | ipx | dnet | link } |
-o[neline]}
# /sbin/ip -r
Usage: ip [ OPTIONS ] OBJECT { COMMAND | help }
where  OBJECT := { link | addr | route | rule | neigh | tunnel |
                   maddr | mroute | monitor }
       OPTIONS := { -V[ersion] | -s[tatistics] | -r[esolve] |
                    -f[amily] { inet | inet6 | ipx | dnet | link } |
-o[neline]}

So -V does what the online help says it does, but -s and -r generate some kind of syntax error.

What am I missing? Should I be modprobing some module someplace? If so, what? How do I tell what modules are available and what they do? Or is all this advanced routing stuff not ready for use yet?

- Greg Scott

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO:
http://ds9a.nl/2.4Routing/

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/2.4Routing/

#2 lore raw
In reply to Greg Scott
Quoted 4 lines · Greg Scott

As I understand things, this is the more or less official HOWTO for the advanced routing stuff.

Well - how come none of it works???

Don't know if it's what you're running into, but certain parts of 'ip' depend on certain options being compiled into the kernel - so some things not working is probably because the Red Hat version of the kernel you're using doesn't support them. Whether Red Hat has provided those functions in modules I don't know - not sure whether they are all module choices if not compiled in.

In my beginner's opinion, that HOWTO would really benefit from a description of precisely which kernel options need to be chosen for various kernel versions. It does mention that you have to have the right options included, but then doesn't specifically list them. On the other hand, in three of four 2.2.19 systems, I've managed to include them somehow and all 'ip' functions appear operational. In the third, 'ip' only partially works - fortunately it's a system where I don't need it.

Anyway, I'd recommend gathering what hints you can, and rolling your own kernel. I've always needed features that distro kernels don't support, and never cared to waste resources running kernels supporting features I don't need.

Whit
@transpect.com

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/2.4Routing/

#3 lore raw
In reply to Greg Scott

On Thu, 1 Nov 2001, Greg Scott wrote:

[snip, that problem was fixed]

Quoted 15 lines

Now I'm really confused. Maybe the online help gives me a clue:

# /sbin/ip help
Usage: ip [ OPTIONS ] OBJECT { COMMAND | help }
where  OBJECT := { link | addr | route | rule | neigh | tunnel |
                   maddr | mroute | monitor }
       OPTIONS := { -V[ersion] | -s[tatistics] | -r[esolve] |
                    -f[amily] { inet | inet6 | ipx | dnet | link } |
-o[neline]}

So let's try a few things:

# /sbin/ip -V
ip utility, iproute2-ss000305
Quoted 7 lines

This seemed to work as advertised.

# /sbin/ip -s
# /sbin/ip -r

So -V does what the online help says it does, but -s and -r generate some kind of syntax error.

The ip tool is somewhat finicky in its input syntax. It does not at all behave like your usual Unix tools but is modeled more like Cisco IOS's commands. Whether this is a good or a bad thing is debatable. However, the -s and -r options only apply when an object and/or command for that object have been specified.

Doei, Arthur.

Signature · 8 lines
  /\    / |      [email protected]      | Work like you don't need the money
 /__\  /  | A friend is someone with whom | Love like you have never been hurt
/    \/__ | you can dare to be yourself   | Dance like there's nobody watching


_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/2.4Routing/