Skip to contentSkip to conversation

basic ip problem

LARTC Raul Dias 2 participants 3 messages Nov 26, 2001 – Dec 2, 2001

lore
Share & tools
lore

Raul Dias

author
#0 lore raw

Hi,

I am creating some routing policy and I am having a basic problem with ip. I am starting with 2 hosts to test the configuration.

   ----------            ----------
   | host A |------------| Host B |
   ----------            ----------
IP: 10.0.100.1           IP: 10.0.100.2

On hostA:

# ip address add 10.0.100.1/24 dev eth0 brd +

On hostB:

# ip address add 10.0.100.2/24 dev eth0 brd +

With this both sides can ping each other (as expected)

Now at host A I get the error:

# ip route add 10.0.100.1/24 dev eth0 table 200
RTNETLINK answers: Invalid argument

I have read the archieves (most of it), the howto and the ip-cred documentation.

However I am still missing something. I don't get what is wrong.

Here is my configurations:

Host A:
- addresses:
1: lo: <LOOPBACK,UP> mtu 16436 qdisc noqueue

    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
    inet 127.0.0.1/8 brd 127.255.255.255 scope host lo
2: eth0: <BROADCAST,MULTICAST,UP> mtu 1500 qdisc pfifo_fast qlen 100
    link/ether 00:01:02:98:40:00 brd ff:ff:ff:ff:ff:ff
    inet XXX.x.x.x/24 brd XXX.x.XX.XX scope global eth0
    inet 10.0.100.1/24 brd 10.0.100.255 scope global eth0

- table main:
10.0.100.0/24 dev eth0 proto kernel scope link src 10.0.100.1 XXX.x.XXX.0/24 dev eth0 proto kernel scope link src XXX.x.XXX.x 127.0.0.0/8 dev lo scope link
default via XXX.x.XXX.x dev eth0

-table local:
broadcast 127.255.255.255 dev lo proto kernel scope link src 127.0.0.1 broadcast 10.0.100.255 dev eth0 proto kernel scope link src 10.0.100.1 local x.x.x.1 dev eth0 proto kernel scope host src x.x.x.1 broadcast x.x.x.255 dev eth0 proto kernel scope link src x.x.x.1 broadcast 10.0.100.0 dev eth0 proto kernel scope link src 10.0.100.1 local 10.0.100.1 dev eth0 proto kernel scope host src 10.0.100.1

broadcast 127.0.0.0 dev lo  proto kernel  scope link  src 127.0.0.1
broadcast x.x.x.0 dev eth0  proto kernel  scope link  src x.x.x.1

local 127.0.0.1 dev lo proto kernel scope host src 127.0.0.1 local 127.0.0.0/8 dev lo proto kernel scope host src 127.0.0.1

On Host B:

- addresses
1: lo: <LOOPBACK,UP> mtu 16436 qdisc noqueue

    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
    inet 127.0.0.1/8 brd 127.255.255.255 scope host lo
2: eth0: <BROADCAST,MULTICAST,UP> mtu 1500 qdisc pfifo_fast qlen 100
    link/ether 00:01:02:71:44:5d brd ff:ff:ff:ff:ff:ff
    inet x.x.x.140/24 brd x.x.x.255 scope global eth0
    inet 10.0.100.2/24 brd 10.0.100.255 scope global eth0

- table main
10.0.100.0/24 dev eth0 proto kernel scope link src 10.0.100.2 x.x.x.0/24 dev eth0 proto kernel scope link src x.x.x.140 127.0.0.0/8 dev lo scope link
default via x.x.x.131 dev eth0

- table local
broadcast 127.255.255.255 dev lo proto kernel scope link src 127.0.0.1 broadcast 10.0.100.255 dev eth0 proto kernel scope link src 10.0.100.2 local x.x.x.140 dev eth0 proto kernel scope host src x.x.x.140 broadcast x.x.x.255 dev eth0 proto kernel scope link src x.x.x.140 broadcast 10.0.100.0 dev eth0 proto kernel scope link src 10.0.100.2 broadcast 127.0.0.0 dev lo proto kernel scope link src 127.0.0.1 local 10.0.100.2 dev eth0 proto kernel scope host src 10.0.100.2 broadcast x.x.x.0 dev eth0 proto kernel scope link src x.x.x.140 local 127.0.0.1 dev lo proto kernel scope host src 127.0.0.1 local 127.0.0.0/8 dev lo proto kernel scope host src 127.0.0.1

On both hosts no special rule (yet):

0:      from all lookup local
32766:  from all lookup main
32767:  from all lookup defaul

Regards,

Raul Dias

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/2.4Routing/

#1 lore raw
Quoted 14 lines · Raul Dias

Hi,

I am creating some routing policy and I am having a basic problem with ip. I am starting with 2 hosts to test the configuration.

   ----------            ----------
   | host A |------------| Host B |
   ----------            ----------
IP: 10.0.100.1           IP: 10.0.100.2

On hostA:

# ip address add 10.0.100.1/24 dev eth0 brd +
Quoted 8 lines

On hostB:

# ip address add 10.0.100.2/24 dev eth0 brd +

With this both sides can ping each other (as expected)

Now at host A I get the error:

# ip route add 10.0.100.1/24 dev eth0 table 200
RTNETLINK answers: Invalid argument

Did you first create this table?

ip rule add <selector> table 200

Regards,

bert

Signature · 8 lines
http://www.PowerDNS.com          Versatile DNS Software & Services
Trilab                                 The Technology People
Netherlabs BV / Rent-a-Nerd.nl           - Nerd Available -
'SYN! .. SYN|ACK! .. ACK!' - the mating call of the internet

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/2.4Routing/
author
#2 lore raw
In reply to Raul Dias
Quoted 8 lines
Quoted 4 lines

Now at host A I get the error:

# ip route add 10.0.100.1/24 dev eth0 table 200
RTNETLINK answers: Invalid argument

Did you first create this table?

ip rule add <selector> table 200

Are you sure that the table has to be created first with 'ip rule' ?

Changing the line to '# ip route add 10.0.100.0/24 dev eth0 table 200' worked.

Regards,

Raul Dias

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/2.4Routing/