How do i configure my kernel for equal cost MultiPath?
I am tyring to get to my machine from both my cable and dialup connection from the outside.
?"How do i configure my kernel for equal cost MultiPath"?
-thx
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/lartc/
Quoted 5 lines · On Thu, 13 Dec 2001 [email protected] wrote:
I am tyring to get to my machine from both my cable and dialup connection from the outside.
?"How do i configure my kernel for equal cost MultiPath"?
i have been trying this http://mailman.ds9a.nl/pipermail/lartc/2000q4/000092.html
assuming these are real ip's
eth2 192.168.1.1 netmask nemask 255.255.255.192 gw 192.168.1.254 ppp0 10.2.2.1/32 gw 10.2.3.254
ip route add 192.168.1.1 dev eth2 table 200
ip route add default via 192.168.1.254 dev eth2 table 200
ip route add 10.2.2.1 dev ppp0 table 100
ip route add default via 10.2.3.254 dev ppp0 table 100
ip route add 192.168.1.1 src 192.168.1.254 dev eth1 ip route add 10.2.2.1 src 10.2.3.254 dev eth2
ip route add default scope global nexthop via 192.168.1.254 \
nexthop via 10.2.3.254i get this error
Error: either "to" is duplicate, or "netxhop" is a garbage
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/lartc/
Yea this is good.. I will dig in
thx
Quoted 33 lines · Christoph Simon
Quoted 6 lines · On Thu, 13 Dec 2001 15:36:01 -0500 (EST) <[email protected]> wrote:
I am tyring to get to my machine from both my cable and dialup connection from the outside.
?"How do i configure my kernel for equal cost MultiPath"?
-thx
This might get you started:
http://www.linuxvirtualserver.org/~julian/#routes
--
Christoph Simon
[email protected]
---
^X^C
q
quit
:q
^C
end
x
exit
ZZ
^D
?
help
.
Quoted 4 lines
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/lartc/
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/lartc/
nope.. same prob
Error: either "to" is duplicate, or "gw" is a garbage.
Quoted 12 lines · Julian Anastasov
Hello,
Quoted 2 lines · On Thu, 13 Dec 2001 [email protected] wrote:
ip route add default scope global nexthop via 192.168.1.254 \ nexthop via 10.2.3.254Simply add "dev XXX" to each nexthop
Regards
Quoted 8 lines
--
Julian Anastasov <[email protected]>_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/lartc/
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/lartc/
Quoted 6 lines · On Thu, 13 Dec 2001 15:36:01 -0500 (EST) <[email protected]> wrote:
I am tyring to get to my machine from both my cable and dialup connection from the outside.
?"How do i configure my kernel for equal cost MultiPath"?
-thx
This might get you started:
http://www.linuxvirtualserver.org/~julian/#routes
--
Christoph Simon
[email protected]
---
^X^C
q
quit
:q
^C
end
x
exit
ZZ
^D
?
help
.
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/lartc/
Hello,
Quoted 2 lines · On Thu, 13 Dec 2001 [email protected] wrote:
ip route add default scope global nexthop via 192.168.1.254 \
nexthop via 10.2.3.254Simply add "dev XXX" to each nexthop
Regards
--
Julian Anastasov <[email protected]>
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/lartc/