Skip to contentSkip to conversation

Nano.Txt with PPP

LARTC mok2 2 participants 9 messages Dec 18, 2001

lore
Share & tools
lore

mok2

author
#0 lore raw

Abbreviations:
IFI internal interface
IPI IP address of internal interface
NMI netmask for the internal interface
IFE1, IFE2 external interfaces
IPE1, IPE2 external IP address
NWE1, NWE2 external network address
NME1, NME2 mask for the external network (number of bits, like in /24)
BRD1, BRD2 broadcast address for external network
GWE1, GWE2 gateway for external interface

I am tyring to setup a gw with a cable modem and a dialup connection. Following the nano.txt, i cant figure out how to define ppp0

ppp0 Link encap:Point-to-Point Protocol
inet addr:166.50.32.206 P-t-P:166.50.32.1 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1 RX packets:4 errors:2 dropped:0 overruns:0 frame:0 TX packets:7 errors:0 dropped:0 overruns:0 carrier:0 collisions:0
RX bytes:40 (40.0 b) TX bytes:92 (92.0 b)

since there is no broadcast or network address that i can tell.

what do i put for these variables..

thx

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/lartc/

author
#2 lore raw
In reply to mok2
Destination     Gateway         Genmask         Flags Metric Ref    Use Iface
166.50.32.1     0.0.0.0         255.255.255.255 UH    0      0        0 ppp0
176.30.3.192    0.0.0.0         255.255.255.192 U     0      0        0 eth2
10.2.2.0        0.0.0.0         255.255.255.0   U     0      0        0 eth0
127.0.0.0       0.0.0.0         255.0.0.0       U     0      0        0 lo
0.0.0.0         176.30.3.193    0.0.0.0         UG    0      0        0 eth2

eth2 Link encap:Ethernet HWaddr

          inet addr:176.30.3.38  Bcast:176.30.3.255  Mask:255.255.255.192
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:98373 errors:0 dropped:0 overruns:0 frame:0
          TX packets:116675 errors:0 dropped:0 overruns:0 carrier:0
          collisions:1015 
          RX bytes:76086367 (72.5 Mb)  TX bytes:97127829 (92.6 Mb)

ppp0 Link encap:Point-to-Point Protocol
inet addr:166.50.33.32 P-t-P:166.50.32.1 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1 RX packets:4 errors:1 dropped:0 overruns:0 frame:0 TX packets:5 errors:0 dropped:0 overruns:0 carrier:0 collisions:0
RX bytes:40 (40.0 b) TX bytes:61 (61.0 b)

the gw with the lowest metric determines which connection will work.. i cannot add in both gw and make both connections work at the same time..

that is my problem..

Quoted 31 lines · Christoph Simon
Quoted 6 lines · On Tue, 18 Dec 2001 14:00:06 -0500 (EST) mok2 <[email protected]> wrote:

I am not tyring to route outbound traffice through ppp0 just recieve traffic on that interface.
while still being connected to my cable provider..

and yes i have a dynamic ip on ppp0 and a static for my cable..

In that case, I'm not sure to understand your problem. You are not going to have any multipath route; it a standard setup.

--
Christoph Simon
[email protected]
---
^X^C
q
quit
:q
^C
end
x
exit
ZZ
^D
?
help
.

Quoted 4 lines

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/lartc/

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/lartc/

#3 lore raw
In reply to mok2
Quoted 22 lines · On Tue, 18 Dec 2001 13:15:45 -0500 (EST) mok2 <[email protected]> wrote:

Abbreviations:
IFI internal interface
IPI IP address of internal interface
NMI netmask for the internal interface
IFE1, IFE2 external interfaces
IPE1, IPE2 external IP address
NWE1, NWE2 external network address
NME1, NME2 mask for the external network (number of bits, like in /24)
BRD1, BRD2 broadcast address for external network
GWE1, GWE2 gateway for external interface

I am tyring to setup a gw with a cable modem and a dialup connection. Following the nano.txt, i cant figure out how to define ppp0

ppp0 Link encap:Point-to-Point Protocol
inet addr:166.50.32.206 P-t-P:166.50.32.1 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1 RX packets:4 errors:2 dropped:0 overruns:0 frame:0 TX packets:7 errors:0 dropped:0 overruns:0 carrier:0 collisions:0
RX bytes:40 (40.0 b) TX bytes:92 (92.0 b)

Quoted 3 lines

since there is no broadcast or network address that i can tell.

what do i put for these variables..

Unfortunately, this isn't such an easy topic that you can just plug and play, specially when your situation is so much different then mine was when I wrote it. I mean, you'll have to bother about the setting of the variables only when it comes to use them. For instance, in iptables, you wouldn' use the SNAT but rather the MASQUERADE target, which doesn't require any IP. On the other hand, if you have an dynamic IP, you will also have to set the routings as soon as the IP is known, i.e., yafter ou have connected and the provider told you what's your IP for now. PPP doesn't imply necessarily a dynamic IP, it's just point-to-point, so I'm not really sure if all this still makes sense for you, because you'll have to reconfigure your network anyway as soon as the connection drops. But if you have a static IP, you do know all of those things. Also, be aware that the use of both lines requires a big amount of traffic, which I was not able to generate alone. I just can't imagine how you are going to route heavy traffic through a dialup line.

--
Christoph Simon
[email protected]
---
^X^C
q
quit
:q
^C
end
x
exit
ZZ
^D
?
help
.

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/lartc/

author
#4 lore raw
In reply to mok2
Quoted 29 lines · Christoph Simon
Quoted 26 lines · On Tue, 18 Dec 2001 14:27:20 -0500 (EST) mok2 <[email protected]> wrote:
Destination     Gateway         Genmask         Flags Metric Ref    Use Iface
166.50.32.1     0.0.0.0         255.255.255.255 UH    0      0        0 ppp0
176.30.3.192    0.0.0.0         255.255.255.192 U     0      0        0 eth2
10.2.2.0        0.0.0.0         255.255.255.0   U     0      0        0 eth0
127.0.0.0       0.0.0.0         255.0.0.0       U     0      0        0 lo
0.0.0.0         176.30.3.193    0.0.0.0         UG    0      0        0 eth2

eth2 Link encap:Ethernet HWaddr

          inet addr:176.30.3.38  Bcast:176.30.3.255  Mask:255.255.255.192
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:98373 errors:0 dropped:0 overruns:0 frame:0
          TX packets:116675 errors:0 dropped:0 overruns:0 carrier:0
          collisions:1015 
          RX bytes:76086367 (72.5 Mb)  TX bytes:97127829 (92.6 Mb)

ppp0 Link encap:Point-to-Point Protocol
inet addr:166.50.33.32 P-t-P:166.50.32.1 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1 RX packets:4 errors:1 dropped:0 overruns:0 frame:0 TX packets:5 errors:0 dropped:0 overruns:0 carrier:0 collisions:0
RX bytes:40 (40.0 b) TX bytes:61 (61.0 b)

the gw with the lowest metric determines which connection will work.. i cannot add in both gw and make both connections work at the same time..

Quoted 8 lines
Quoted 1 line

that is my problem..

If you try to access 166.50.32.1/32, ppp0 will be used. If you try to access 10.2.2.0/24, eth0 will be used. In all other cases, eth2 will be used. This should just work. What do you expect to work and doesn't? BTW, normally there is no explicit route for lo; the kernel does know how to deal with the loop back.

i cannot access 166.50.33.32 from the outside

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/lartc/

#5 lore raw
In reply to mok2
Quoted 6 lines · On Tue, 18 Dec 2001 14:00:06 -0500 (EST) mok2 <[email protected]> wrote:

I am not tyring to route outbound traffice through ppp0 just recieve traffic on that interface.
while still being connected to my cable provider..

and yes i have a dynamic ip on ppp0 and a static for my cable..

In that case, I'm not sure to understand your problem. You are not going to have any multipath route; it a standard setup.

--
Christoph Simon
[email protected]
---
^X^C
q
quit
:q
^C
end
x
exit
ZZ
^D
?
help
.

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/lartc/

author
#6 lore raw
In reply to mok2

if i change my default gw to the dialup isp
than it works...
but the cable gw now has a higher metric .. so it wont work now..

i can only use one of the connections at a time .. and the only one that works with is the connection with the lowest metric..

Quoted 26 lines · Christoph Simon
Quoted 1 line · On Tue, 18 Dec 2001 15:06:07 -0500 (EST) mok2 <[email protected]> wrote:

i cannot access 166.50.33.32 from the outside

If you can access it from inside, the problem is at the other end.

--
Christoph Simon
[email protected]
---
^X^C
q
quit
:q
^C
end
x
exit
ZZ
^D
?
help
.

Quoted 4 lines

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/lartc/

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/lartc/

#7 lore raw
In reply to mok2
Quoted 23 lines · On Tue, 18 Dec 2001 14:27:20 -0500 (EST) mok2 <[email protected]> wrote:
Destination     Gateway         Genmask         Flags Metric Ref    Use Iface
166.50.32.1     0.0.0.0         255.255.255.255 UH    0      0        0 ppp0
176.30.3.192    0.0.0.0         255.255.255.192 U     0      0        0 eth2
10.2.2.0        0.0.0.0         255.255.255.0   U     0      0        0 eth0
127.0.0.0       0.0.0.0         255.0.0.0       U     0      0        0 lo
0.0.0.0         176.30.3.193    0.0.0.0         UG    0      0        0 eth2

eth2 Link encap:Ethernet HWaddr

          inet addr:176.30.3.38  Bcast:176.30.3.255  Mask:255.255.255.192
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:98373 errors:0 dropped:0 overruns:0 frame:0
          TX packets:116675 errors:0 dropped:0 overruns:0 carrier:0
          collisions:1015 
          RX bytes:76086367 (72.5 Mb)  TX bytes:97127829 (92.6 Mb)

ppp0 Link encap:Point-to-Point Protocol
inet addr:166.50.33.32 P-t-P:166.50.32.1 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1 RX packets:4 errors:1 dropped:0 overruns:0 frame:0 TX packets:5 errors:0 dropped:0 overruns:0 carrier:0 collisions:0
RX bytes:40 (40.0 b) TX bytes:61 (61.0 b)

Quoted 4 lines

the gw with the lowest metric determines which connection will work.. i cannot add in both gw and make both connections work at the same time..

that is my problem..

If you try to access 166.50.32.1/32, ppp0 will be used. If you try to access 10.2.2.0/24, eth0 will be used. In all other cases, eth2 will be used. This should just work. What do you expect to work and doesn't? BTW, normally there is no explicit route for lo; the kernel does know how to deal with the loop back.

--
Christoph Simon
[email protected]
---
^X^C
q
quit
:q
^C
end
x
exit
ZZ
^D
?
help
.

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/lartc/