Skip to contentSkip to conversation

Traffic shaping an apartment building

LARTC Allen Armstrong 3 participants 5 messages Dec 27, 2001 – Dec 28, 2001

lore
Share & tools
lore
#0 lore raw

Hi,

I live in a rural community where adsl and cable is not widely available. I correctly have an option of using adsl or cable at my location. Ten miles away my friends apartment building has no option of cable or adsl. I set-up a wireless link between my friends apartment building and my house. It works great for him and me and the adsl company doesn't care because they don't cover the area and we aren't going over our bandwidth allotments.

Old setup:

	ADSL (dynamic)
	 |
	NAT linux box ( inside 192.168.1.0) (486s)
	 |
	My internal network (192.168.1.0) (Just a small network really!)
	|
	Wireless radio (192.168.1.0)
	|
	Wireless radio (192.168.1.0)
	|
	His internal network (192.168.1.0)

We have been using this set-up for few months and we share the bandwidth and he paid the costs of wireless radios. His apartment got wind what we are doing and want a connection. To make a long story short we want to run a cable to the phone room and then up to each apartment so logistically we can do it. However, I am not interested in giving everyone in this apartment a full connection speed connection to the internet. I don't know them. :-)

I have set-up a redhat 7.2 box /w 2.4.7 kernel all the stuff I need seems to be in built-in the kernel. Reading the list archives I setup a proxy-arp bridge and its been working fine.

	ADSL (dynamic)
	 |
	NAT linux box ( inside 192.168.1.0) (486s)
	 |
	My internal network (192.168.1.0) (Just a small network really!)
	|
	Redhat 7.2 box 2.4.7 (Proxy-arp with 2 nics)
	|
	Wireless radio (192.168.1.0)
	|
	Wireless radio (192.168.1.0)
	|
	His internal network (192.168.1.0)

I had look at http://www.docum.org/ and http://ds9a.nl/lartc/. I just not sure what I need to do next I have read the documents at the latter and it seems confusing to me. What I would like to do is give almost everyone in the apartment a 64k connection with exception of my friends machines (384k) and apartment manager machine (384k).

Allen Armstrong

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/lartc/

#1 lore raw
Quoted 41 lines · Allen Armstrong

Hi,

I live in a rural community where adsl and cable is not widely available. I correctly have an option of using adsl or cable at my location. Ten miles away my friends apartment building has no option of cable or adsl. I set-up a wireless link between my friends apartment building and my house. It works great for him and me and the adsl company doesn't care because they don't cover the area and we aren't going over our bandwidth allotments.

Old setup:

	ADSL (dynamic)
	NAT linux box ( inside 192.168.1.0) (486s)
	My internal network (192.168.1.0) (Just a small network really!)
	Wireless radio (192.168.1.0)
	Wireless radio (192.168.1.0)
	His internal network (192.168.1.0)

We have been using this set-up for few months and we share the bandwidth and he paid the costs of wireless radios. His apartment got wind what we are doing and want a connection. To make a long story short we want to run a cable to the phone room and then up to each apartment so logistically we can do it. However, I am not interested in giving everyone in this apartment a full connection speed connection to the internet. I don't know them. :-)

I have set-up a redhat 7.2 box /w 2.4.7 kernel all the stuff I need seems to be in built-in the kernel. Reading the list archives I setup a proxy-arp bridge and its been working fine.

	ADSL (dynamic)
	NAT linux box ( inside 192.168.1.0) (486s)
	My internal network (192.168.1.0) (Just a small network really!)
	Redhat 7.2 box 2.4.7 (Proxy-arp with 2 nics)
	Wireless radio (192.168.1.0)
	Wireless radio (192.168.1.0)
	His internal network (192.168.1.0)
Quoted 5 lines

I had look at http://www.docum.org/ and http://ds9a.nl/lartc/. I just not sure what I need to do next I have read the documents at the latter and it seems confusing to me. What I would like to do is give almost everyone in the apartment a 64k connection with exception of my friends machines (384k) and apartment manager machine (384k).

I have a better idea. ;-)

You can give erveyone the full bandwith. But if you your friend is downloading (or you), he gets more bandwith. I think that's more fair then limiting everyone to 64k.
And I suggest you use HTB and CBQ. But you will have to patch the kernel and iproute to do so.
You can do it with CBQ, but it's much more complicated.

What kind of upload/download do you have on the ADSL link and the wireless radio?

Stef

Signature · 8 lines
[email protected]
 More QOS info : http://www.docum.org/
 Title : "Using Linux as bandwidth manager"
     

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/lartc/
#2 lore raw
In reply to Allen Armstrong
Quoted 40 lines

-----Original Message-----
From: Stef Coene [mailto:[email protected]]
Sent: December 27, 2001 2:20 AM
To: Allen Armstrong; [email protected]
Subject: Re: [LARTC] Traffic shaping an apartment building

Quoted 3 lines · Allen Armstrong

Hi,

I live in a rural community where adsl and cable is not

widely available.

Quoted 1 line

I correctly have an option of using adsl or cable at my

location. Ten

Quoted 1 line

miles away my friends apartment building has no option of

cable or adsl. I

Quoted 1 line

set-up a wireless link between my friends apartment

building and my house.

Quoted 1 line

It works great for him and me and the adsl company doesn't

care because

Quoted 13 lines

they don't cover the area and we aren't going over our bandwidth allotments.

Old setup:

	ADSL (dynamic)
	NAT linux box ( inside 192.168.1.0) (486s)
	My internal network (192.168.1.0) (Just a small network really!)
	Wireless radio (192.168.1.0)
	Wireless radio (192.168.1.0)
	His internal network (192.168.1.0)
Quoted 1 line

We have been using this set-up for few months and we share

the bandwidth

Quoted 1 line

and he paid the costs of wireless radios. His apartment

got wind what we

Quoted 1 line

are doing and want a connection. To make a long story

short we want to run

Quoted 1 line

a cable to the phone room and then up to each apartment so

Quoted 21 lines

logistically we

Quoted 2 lines

can do it. However, I am not interested in giving everyone in this apartment a full connection speed connection to the

internet. I don't know

Quoted 3 lines

them. :-)

I have set-up a redhat 7.2 box /w 2.4.7 kernel all the

stuff I need seems

Quoted 13 lines

to be in built-in the kernel. Reading the list archives I setup a proxy-arp bridge and its been working fine.

	ADSL (dynamic)
	NAT linux box ( inside 192.168.1.0) (486s)
	My internal network (192.168.1.0) (Just a small network really!)
	Redhat 7.2 box 2.4.7 (Proxy-arp with 2 nics)
	Wireless radio (192.168.1.0)
	Wireless radio (192.168.1.0)
	His internal network (192.168.1.0)

I had look at http://www.docum.org/ and

http://ds9a.nl/lartc/. I just not

Quoted 3 lines

sure what I need to do next I have read the documents at the latter and it seems confusing to me. What I would like to do is give almost everyone in the apartment a 64k connection with exception of my friends machines

(384k)

Quoted 5 lines

and apartment manager machine (384k).

Quoted 3 lines

I have a better idea. ;-)
You can give erveyone the full bandwith. But if you your friend is downloading (or you), he gets more bandwith. I think that's more fair

then

Quoted 1 line
Quoted 1 line

limiting everyone to 64k.

I thought of that but the people at this apartment are cheap. :( I was going to charge them 10$ a month X 20 to cover the cost of the access and to recover the cost of the wireless equipment. If they pay more I will up their rate. Our eventual goal is get them on their own dsl modem.

Quoted 1 line
Quoted 1 line

And I suggest you use HTB and CBQ. But you will have to patch the kernel

and

Quoted 3 lines
Quoted 3 lines

iproute to do so.
You can do it with CBQ, but it's much more complicated.

I hear a lot about the buzzword CBQ. What do I if I wish to follow the CBQ route? Do I have to re-compile my stock Redhat 7.2 kernel? Everything looks like it is a module when it comes to QOS in this kernel. QOS is all new to me but Linux and routing isn't. :) Tomorrow I am going to re-read the sections on both sites again.

Quoted 1 line
Quoted 1 line

What kind of upload/download do you have on the ADSL link and the

wireless

Quoted 1 line
Quoted 1 line

radio?

When we first did the link we didn't get that good transfer rates 64-128 k, he slapped another 2000$ for some Amps now we are getting about 6 meg link reliably. The ADSL I am getting 3 megs down 512 k up.

Allen Armstrong

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/lartc/

#3 lore raw
In reply to Allen Armstrong

Hi,
I recomend you to use HTB.
It's prety simple and easy to configure
http://luxik.cdi.cz/~devik/qos/htb/htbman.htm

Quoted 54 lines

Hi,

I live in a rural community where adsl and cable is not widely available. I correctly have an option of using adsl or cable at my location. Ten miles away my friends apartment building has no option of cable or adsl. I set-up a wireless link between my friends apartment building and my house. It works great for him and me and the adsl company doesn't care because they don't cover the area and we aren't going over our bandwidth allotments.

Old setup:

        ADSL (dynamic)
         |
        NAT linux box ( inside 192.168.1.0) (486s)
         |
        My internal network (192.168.1.0) (Just a small network really!)
        |
        Wireless radio (192.168.1.0)
        |
        Wireless radio (192.168.1.0)
        |
        His internal network (192.168.1.0)

We have been using this set-up for few months and we share the bandwidth and he paid the costs of wireless radios. His apartment got wind what we are doing and want a connection. To make a long story short we want to run a cable to the phone room and then up to each apartment so logistically we can do it. However, I am not interested in giving everyone in this apartment a full connection speed connection to the internet. I don't know them. :-)

I have set-up a redhat 7.2 box /w 2.4.7 kernel all the stuff I need seems to be in built-in the kernel. Reading the list archives I setup a proxy-arp bridge and its been working fine.

        ADSL (dynamic)
         |
        NAT linux box ( inside 192.168.1.0) (486s)
         |
        My internal network (192.168.1.0) (Just a small network really!)
        |
        Redhat 7.2 box 2.4.7 (Proxy-arp with 2 nics)
        |
        Wireless radio (192.168.1.0)
        |
        Wireless radio (192.168.1.0)
        |
        His internal network (192.168.1.0)

I had look at http://www.docum.org/ and http://ds9a.nl/lartc/. I just not sure what I need to do next I have read the documents at the latter and it seems confusing to me. What I would like to do is give almost everyone in the apartment a 64k connection with exception of my friends machines (384k) and apartment manager machine (384k).

Quoted 5 lines

Allen Armstrong

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/lartc/

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/lartc/

#4 lore raw
In reply to Allen Armstrong
Quoted 10 lines
Quoted 3 lines
Quoted 3 lines

I have a better idea. ;-)
You can give erveyone the full bandwith. But if you your friend is downloading (or you), he gets more bandwith. I think that's more fair

then

Quoted 1 line
Quoted 1 line

limiting everyone to 64k.

I thought of that but the people at this apartment are cheap. :( I was going to charge them 10$ a month X 20 to cover the cost of the access and to recover the cost of the wireless equipment. If they pay more I will up their rate. Our eventual goal is get them on their own dsl modem.

You still can use the same setup as I described. They can share the bandwidth between each other, but there is a maximum. If they pay more, you increase the maximum:
root qdisc
bounded class with rate = 3meg
class for the 'manager' : rate = 384K
class for the other appartments : rate = 3meg - 348k
class 1 for appartment 1 : rate = 64k
class 2 for appartment 2 : rate = 64k
...

Quoted 6 lines
Quoted 3 lines
Quoted 3 lines

And I suggest you use HTB and CBQ. But you will have to patch the kernel

and

Quoted 8 lines
Quoted 2 lines
Quoted 2 lines

iproute to do so.
You can do it with CBQ, but it's much more complicated.

I hear a lot about the buzzword CBQ. What do I if I wish to follow the CBQ route? Do I have to re-compile my stock Redhat 7.2 kernel? Everything looks like it is a module when it comes to QOS in this kernel. QOS is all new to me but Linux and routing isn't. :) Tomorrow I am going to re-read the sections on both sites again.

I suppose you mean "What do I if I wish to follow the HTB". Indeed, you will have to download the kernel source and iproute and patch it for HTB. But that's not so difficult. Maybe that
redhat allready prepatched his kernel for htb, I don't know.

Stef

Quoted 8 lines
Quoted 2 lines
Quoted 2 lines

What kind of upload/download do you have on the ADSL link and the

wireless

Quoted 1 line
Quoted 1 line

radio?

When we first did the link we didn't get that good transfer rates 64-128 k, he slapped another 2000$ for some Amps now we are getting about 6 meg link reliably. The ADSL I am getting 3 megs down 512 k up.

Signature · 8 lines
[email protected]
 More QOS info : http://www.docum.org/
 Title : "Using Linux as bandwidth manager"
     

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/lartc/