routing network through bastian host
Hello,
This seems to be a common problem but AFAIK, without a common solution. The network map is as follows:
T1 to ISP
|
| /30 net
|
+----------------+
| cisco router |
+----------------+
| FastEthernet0/0
| a.b.c.1/24
|
(possible switch/hub here in future)
|
| a.b.c.2/24
| eth0
+----------------+
| |
| eth1 |---a.b.c.3/24-public-net-----> lan
| linux box |
| eth2 |---192.168.1.0/24-private-net---> lan
| |
+----------------+Of course the above does not work as eth0 and eth1 are on the same subnet. So far, I can see two possible solutions:
1. reassign the cisco to linux net to a private point to point /30 net. I have tried with limited success.
2. reassign the cisco to linux net to a.b.c.1/29 (cisco) and a.b.c.2/29 (linux box). This would give me a block of 8 between cisco and linux and would enable me to add a switch/hub between to feed another host for backup mail relay and dns server.
Questions:
1. Does a different subnet mask define a different subnet? Will the "two nics same net" conflict be resolved by applying a longer mask to one subnet?
2. What is required to route through the linux box in "solution" 2 above? Is this a case of "more specific, preferred route" applied?
3. Any relevant RFC's would be helpful.
4. Of course, ANY suggestions welcome.
TIA,
David Koski
[email protected]
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/lartc/
Is your LAN off of eth1 a DMZ with some kind of publicly availble server that you want protected? You could put it in another private address range, say 192.168.10.0/24 and then use SNAT and DNAT to disguise it from the world.
Or you could split up a.b.c.0/24 into two sets of a.b.c.0/25 and a.b.c.128/25 if you need real routable IP addresses on this DMZ system.
You will want the same subnet mask on your a.b.c.<whatevers> unless you plan to subnet it even more when you get farther inside. Remember, the mask determines which bits are the network and which bits are the host. So it needs to be consistent all the way through.
- Greg
-----Original Message-----
From: David Koski [mailto:[email protected]]
Sent: Monday, January 28, 2002 3:07 PM
To: [email protected]
Subject: [LARTC] routing network through bastian host
Hello,
This seems to be a common problem but AFAIK, without a common solution. The network map is as follows:
T1 to ISP
|
| /30 net
|
+----------------+
| cisco router |
+----------------+
| FastEthernet0/0
| a.b.c.1/24
|
(possible switch/hub here in future)
|
| a.b.c.2/24
| eth0
+----------------+
| |
| eth1 |---a.b.c.3/24-public-net-----> lan
| linux box |
| eth2 |---192.168.1.0/24-private-net---> lan
| |
+----------------+Of course the above does not work as eth0 and eth1 are on the same subnet. So
far, I can see two possible solutions:
1. reassign the cisco to linux net to a private point to point /30 net. I have
tried with limited success.
2. reassign the cisco to linux net to a.b.c.1/29 (cisco) and a.b.c.2/29 (linux
box). This would give me a block of 8 between cisco and linux and would enable
me to add a switch/hub between to feed another host for backup mail relay and
dns server.
Questions:
1. Does a different subnet mask define a different subnet? Will the "two nics
same net" conflict be resolved by applying a longer mask to one subnet?
2. What is required to route through the linux box in "solution" 2 above? Is
this a case of "more specific, preferred route" applied?
3. Any relevant RFC's would be helpful.
4. Of course, ANY suggestions welcome.
TIA,
David Koski
[email protected]
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/lartc/
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/lartc/
Hello Greg,
The LAN off eth1 will provide public services and is allocated to isp clients. Hiding is not an option and splitting the net in half will loose too many ip's. I have been looking into proxy ARP and it looks like the ticket. However, I don't know if it is necessary under the following conditions:
1. The default route for a.b.c.0/24 hosts on LAN A use default route a.b.c.3.
2. The default route for a.b.c.0/24 for the cisco is a.b.c.2/29 (I don't know how to do this!)
3. The following assignments are used:
T1 to ISP
|
| /30 net
|
+----------------+
| cisco router |
+----------------+
| FastEthernet0/0
| a.b.c.1/29
|
(possible switch/hub here in future)
|
| a.b.c.2/29
| eth0
+----------------+
| |
| eth1 |---a.b.c.3/24-public-net-----> LAN A
| linux box |
| eth2 |---192.168.1.0/24-private-net---> LAN B
| |
+----------------+It seems logical to me that all routing would work with the above configuration.
Proxy ARP looks easy enough though.
David Koski
[email protected]
Quoted 82 lines · On Mon, 28 Jan 2002 18:46:58 -0600 Greg Scott <[email protected]>…
Is your LAN off of eth1 a DMZ with some kind of publicly availble server that you want protected? You could put it in another private address range, say 192.168.10.0/24 and then use SNAT and DNAT to disguise it from the world.
Or you could split up a.b.c.0/24 into two sets of a.b.c.0/25 and a.b.c.128/25 if you need real routable IP addresses on this DMZ system.
You will want the same subnet mask on your a.b.c.<whatevers> unless you plan to subnet it even more when you get farther inside. Remember, the mask determines which bits are the network and which bits are the host. So it needs to be consistent all the way through.
- Greg
-----Original Message-----
From: David Koski [mailto:[email protected]]
Sent: Monday, January 28, 2002 3:07 PM
To: [email protected]
Subject: [LARTC] routing network through bastian hostHello,
This seems to be a common problem but AFAIK, without a common solution. The network map is as follows:
T1 to ISP | | /30 net | +----------------+ | cisco router | +----------------+ | FastEthernet0/0 | a.b.c.1/24 | (possible switch/hub here in future) | | a.b.c.2/24 | eth0 +----------------+ | | | eth1 |---a.b.c.3/24-public-net-----> lan | linux box | | eth2 |---192.168.1.0/24-private-net---> lan | | +----------------+Of course the above does not work as eth0 and eth1 are on the same subnet. So
far, I can see two possible solutions:1. reassign the cisco to linux net to a private point to point /30 net. I have
tried with limited success.2. reassign the cisco to linux net to a.b.c.1/29 (cisco) and a.b.c.2/29 (linux
box). This would give me a block of 8 between cisco and linux and would enable
me to add a switch/hub between to feed another host for backup mail relay and
dns server.Questions:
1. Does a different subnet mask define a different subnet? Will the "two nics
same net" conflict be resolved by applying a longer mask to one subnet?2. What is required to route through the linux box in "solution" 2 above? Is
this a case of "more specific, preferred route" applied?3. Any relevant RFC's would be helpful.
4. Of course, ANY suggestions welcome.
Quoted 9 lines
TIA,
David Koski
[email protected]
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/lartc/
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/lartc/
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/lartc/
Why put LAN A behind a firewall? If it's all public and visible, why not just put it in front of the firewall? Well, probably cuz you want to filter packets. duh! So, OK, what if you used private addresses in LAN A and used DNAT to redirect ports and/or public IP addresses to the correct host(s) inside LAN A. But if you have customers doing VPN stuff or IPSEC stuff, this won't work. And there are probably a bunch of other apps that NAT breaks.
I wonder if you could you get a d.e.f.nn/29 from your ISP and use those addresses for FastEthernet 0/0 on the Cisco and eth0 on the firewall? Now that would be the ultimate.
Also, pointing your default gateway of your Cisco back inside your LAN seems funny. Wouldn't you want to point that out, not in?
- Greg
-----Original Message-----
From: David Koski [mailto:[email protected]]
Sent: Monday, January 28, 2002 7:55 PM
To: Greg Scott; [email protected]
Subject: Re: [LARTC] routing network through bastian host
Hello Greg,
The LAN off eth1 will provide public services and is allocated to isp clients.
Hiding is not an option and splitting the net in half will loose too many ip's.
I have been looking into proxy ARP and it looks like the ticket. However, I don't know if it is necessary under the following conditions:
1. The default route for a.b.c.0/24 hosts on LAN A use default route a.b.c.3.
2. The default route for a.b.c.0/24 for the cisco is a.b.c.2/29 (I don't know
how to do this!)
3. The following assignments are used:
T1 to ISP
|
| /30 net
|
+----------------+
| cisco router |
+----------------+
| FastEthernet0/0
| a.b.c.1/29
|
(possible switch/hub here in future)
|
| a.b.c.2/29
| eth0
+----------------+
| |
| eth1 |---a.b.c.3/24-public-net-----> LAN A
| linux box |
| eth2 |---192.168.1.0/24-private-net---> LAN B
| |
+----------------+It seems logical to me that all routing would work with the above configuration.
Proxy ARP looks easy enough though.
David Koski
[email protected]
Quoted 25 lines · On Mon, 28 Jan 2002 18:46:58 -0600 Greg Scott <[email protected]>…
Is your LAN off of eth1 a DMZ with some kind of publicly availble server that you want protected? You could put it in another private address range, say 192.168.10.0/24 and then use SNAT and DNAT to disguise it from the world.
Or you could split up a.b.c.0/24 into two sets of a.b.c.0/25 and a.b.c.128/25 if you need real routable IP addresses on this DMZ system.
You will want the same subnet mask on your a.b.c.<whatevers> unless you plan to subnet it even more when you get farther inside. Remember, the mask determines which bits are the network and which bits are the host. So it needs to be consistent all the way through.
- Greg
-----Original Message-----
From: David Koski [mailto:[email protected]]
Sent: Monday, January 28, 2002 3:07 PM
To: [email protected]
Subject: [LARTC] routing network through bastian host
Quoted 3 lines
Hello,
This seems to be a common problem but AFAIK, without a common solution.
The
Quoted 54 lines
network map is as follows:
T1 to ISP | | /30 net | +----------------+ | cisco router | +----------------+ | FastEthernet0/0 | a.b.c.1/24 | (possible switch/hub here in future) | | a.b.c.2/24 | eth0 +----------------+ | | | eth1 |---a.b.c.3/24-public-net-----> lan | linux box | | eth2 |---192.168.1.0/24-private-net---> lan | | +----------------+Of course the above does not work as eth0 and eth1 are on the same subnet. So
far, I can see two possible solutions:1. reassign the cisco to linux net to a private point to point /30 net. I have
tried with limited success.2. reassign the cisco to linux net to a.b.c.1/29 (cisco) and a.b.c.2/29 (linux
box). This would give me a block of 8 between cisco and linux and would enable
me to add a switch/hub between to feed another host for backup mail relay and
dns server.Questions:
1. Does a different subnet mask define a different subnet? Will the "two nics
same net" conflict be resolved by applying a longer mask to one subnet?2. What is required to route through the linux box in "solution" 2 above? Is
this a case of "more specific, preferred route" applied?3. Any relevant RFC's would be helpful.
4. Of course, ANY suggestions welcome.
Quoted 9 lines
TIA,
David Koski
[email protected]
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/lartc/
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/lartc/
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/lartc/
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/lartc/
Re: [LARTC] routing network through bastian host (fwd)
In reply to David Koskihehe, forgot to send it to the list too.
---------- Forwarded message ----------
Date: Tue, 29 Jan 2002 00:40:47 +0100 (CET)
From: Leen Besselink <[email protected]>
To: David Koski <[email protected]>
Subject: Re: [LARTC] routing network through bastian host
Quoted 4 lines
Hello Leen,
I think proxy ARP is the ticket. Thanks for the help!
np.
Quoted 1 line
David
Let me know how it works out, as I'm gonna build something similair. Maybe you can send me your setup or something...
I've got a bit more complicated situation then you and I can use all the help I can get. :)
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/lartc/
Re: [LARTC] routing network through bastian host (fwd)
In reply to David Koskiit was late last night, it's this one...
geez... well atleast I feel I have the right answer... :)
---------- Forwarded message ----------
Date: Tue, 29 Jan 2002 00:23:51 +0100
From: Leen Besselink <[email protected]>
To: David Koski <[email protected]>
Subject: Re: [LARTC] routing network through bastian host
Quoted 2 lines · * David Koski ([email protected]) wrote:
Hello,
Hi,
[..]
Look for arp-proxy, this could be a way to solve your problem, one such resource is here:
http://www.sjdjweis.com/linux/proxyarp/
There is also a much smaller explanation in the HOWTO (pseudo bridges with Proxy-arp)
[..]
PS Please if any network/routing/firewalling guru knowns of a better cleaner way, do tell me.
-------------------------------------
New things are always on the horizon.
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/lartc/
David, Greg,
Is it not possible to have some private address space between the cisco router and the linux box ?
sth like this:
cisco
192.168.1.1/24
|
|
(possible hub/switch)
|
|192.168.1.2/24
linux
box
So, everything comming from the ISP for a.b.c.nn/24 will route to 192.168.1.1 ?
(I'm new to this, so don't laugh too much, pls ;)
-kosio
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/lartc/