Skip to contentSkip to conversation

Queries

LARTC Stef Coene 2 participants 3 messages Jan 30, 2002 – Jan 31, 2002

lore
Share & tools
lore

Stef Coene

author
#0 lore raw
Quoted 19 lines · Arindam Haldar

hi all,
hi stef,

stef i went thru the site www.docum.org & would really like to thank u on one part--->monitor.pl.. :-).. havent tried it yestreday but will today when i find time but reading it i know that ... :-)
1) comming accros 2 one of the pages --> www.docum.org/stef.coene/qos/tests/cbq/splitting/weight/splitting-weight.ht ml ..i saw these 4 lines & got curious 2know y ur sending pkts with mark of 1 & 2 to both classes 10:2 & 20:10 ?..wont there b confusion 2 what rulesse 2b applied?
tc filter add $DEV parent 10: protocol ip prio 3 handle 1 fw classid 10:2
tc filter add $DEV parent 10: protocol ip prio 3 handle 2 fw classid 10:2
tc filter add $DEV parent 20: protocol ip prio 3 handle 1 fw classid 20:10
tc filter add $DEV parent 20: protocol ip prio 3 handle 2 fw classid 20:20

The filters are attached to different parents. So when a packets enters 10:, it's matched. If it has mark 1 it's sended to class 10:2. But qdisc 20: is attached to 10:2 so the packet is matched to the filter that puts the packet in 20:10. This test was to see how you have to attach the filters. But it's not recommended to use more then 1 qdisc in your setup.

Quoted 20 lines

2) our linux box does managemnt of public lan(office ) & pvt lan(cable)--by ip's.. sucess with public ips, marking & using tc filter is sucessful but not true with pvt ips (10 series, marking part!).. to let u know better here is what we did with public ip.. iptables -t mangle -A PREROUTING -i eth1 -s <a.b.c.0/26> -d
<a.b.e.0/25> -j MARK --set-mark 90
iptables -t mangle -A PREROUTING -i eth0 -d <a.b.c.0/26> -s
<a.b.e.0/25> -j MARK --set-mark 91
the tc commands
tc filter add dev eth0 parent 1:105 pfifo limit 2
tc filter add dev eth1 parent 2:105 pfifo limit 2
This works fine--tested with different traffic loads of download& upload.
BUT with lan on eth4 which has pvt ip range(10series) vr not sucesful. the problem is how to make sure that the pkts detination for 10.0.0.0/8 should be marked as they r MASQUERADEd. so i trired to mark with FORWARD/OUTPUT/POSTROUTING but unsuccesful. tc -s class.... etc command doesnt show any data being passed thru the class while iptables -nvL -t mangle shows pkts r being marked & passing thru.

Quoted 2 lines

3) do we need to reset/restart the iptables script when iproute script is reapplied or vice versa ?

Nop.

Stef

Signature · 7 lines
[email protected]
 More QOS info : http://www.docum.org/
 Title : "Using Linux as bandwidth manager"
     
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/lartc/
#1 lore raw

hi again !
thanx for ur mail.

Quoted 19 lines · Stef Coene
Quoted 10 lines · Arindam Haldar

hi all,
hi stef,
stef i went thru the site www.docum.org & would really like to thank u on one part--->monitor.pl.. :-).. havent tried it yestreday but will today when i find time but reading it i know that ... :-)
1) comming accros 2 one of the pages --> www.docum.org/stef.coene/qos/tests/cbq/splitting/weight/splitting-weight.ht ml ..i saw these 4 lines & got curious 2know y ur sending pkts with mark of 1 & 2 to both classes 10:2 & 20:10 ?..wont there b confusion 2 what rulesse 2b applied?

Quoted 8 lines

tc filter add $DEV parent 10: protocol ip prio 3 handle 1 fw classid 10:2
tc filter add $DEV parent 10: protocol ip prio 3 handle 2 fw classid 10:2
tc filter add $DEV parent 20: protocol ip prio 3 handle 1 fw classid 20:10
tc filter add $DEV parent 20: protocol ip prio 3 handle 2 fw classid 20:20

Quoted 25 lines

The filters are attached to different parents. So when a packets enters 10:, it's matched. If it has mark 1 it's sended to class 10:2. But qdisc 20: is attached to 10:2 so the packet is matched to the filter that puts the packet in 20:10. This test was to see how you have to attach the filters. But it's not recommended to use more then 1 qdisc in your setup.

Quoted 19 lines

2) our linux box does managemnt of public lan(office ) & pvt lan(cable)--by ip's.. sucess with public ips, marking & using tc filter is sucessful but not true with pvt ips (10 series, marking part!).. to let u know better here is what we did with public ip.. iptables -t mangle -A PREROUTING -i eth1 -s <a.b.c.0/26> -d
<a.b.e.0/25> -j MARK --set-mark 90
iptables -t mangle -A PREROUTING -i eth0 -d <a.b.c.0/26> -s
<a.b.e.0/25> -j MARK --set-mark 91
the tc commands
tc filter add dev eth0 parent 1:105 pfifo limit 2
tc filter add dev eth1 parent 2:105 pfifo limit 2
This works fine--tested with different traffic loads of download& upload.
BUT with lan on eth4 which has pvt ip range(10series) vr not sucesful. the problem is how to make sure that the pkts detination for 10.0.0.0/8 should be marked as they r MASQUERADEd. so i trired to mark with FORWARD/OUTPUT/POSTROUTING but unsuccesful. tc -s class.... etc command doesnt show any data being passed thru the class while iptables -nvL -t mangle shows pkts r being marked & passing thru.

have u tried with using private ips as described above in any of ur experiments? i am really curious to know how i can mark pkts comming on eth0(internet) tracelling thru eth4(pvt Lan).basically wanting to have a effective filter/routing/bandwidth usage. for eg i want to give ftp/imap a more bandwidth for local pc(private ip) to our local server having public ip.

Quoted 4 lines
Quoted 3 lines

3) do we need to reset/restart the iptables script when iproute script is reapplied or vice versa ?

Nop.

i need one more help guidance on setting of web enabled badwidth utilisation u have described in ur site. i will be really thankful if u can tell me how i can implement it. im not into perl that makes things a bit difficult for me though i ma trying to.

Quoted 8 lines

Stef
--

[email protected]
More QOS info : http://www.docum.org/
Title : "Using Linux as bandwidth manager"

thanx in advance
arindam

Signature · 7 lines
Arindam Haldar
Systems & Network
Digital 2 Virtual ISP Pvt Ltd.
Vadodara, Gujarat  INDIA
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/lartc/
author
#2 lore raw
In reply to Stef Coene
Quoted 4 lines

i need one more help guidance on setting of web enabled badwidth utilisation u have described in ur site. i will be really thankful if u can tell me how i can implement it. im not into perl that makes things a bit difficult for me though i ma trying to.

For those who are interested, I created some perl script to process the tc output. Currently, it takes the packets/bytes sended by a class/qdisc and makes some graphs with it. You can find it on www.docum.org under "GUI". They use RRDs.pm so you have to install rrdtool (apt-get install librrds-perl on a Debian based system).

I want to extend the scripts, but for now, they just create some nice looking graphs. But help is appreciated :-)
I'm still writing the pages and hopely I can update them tonight.

Stef

Signature · 7 lines
[email protected]
 More QOS info : http://www.docum.org/
 Title : "Using Linux as bandwidth manager"
     
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/lartc/