Skip to contentSkip to conversation

Partial Isolation

LARTC Michael T. Babcock 3 participants 5 messages Feb 22, 2002

lore
Share & tools
lore
#0 lore raw

Lets say I wanted to allocate 50kbps to SSH traffic, but I didn't want to set it all as isolated. What if I wanted to set aside 20k of that as being isolated from other classes (either in HTB or CBQ), how would I go about this, or is it even possible? Would I have to make the normal class of 50k and then make a sub-class of 20 with the same definition but isolated? Should this work?

root
\---1:1 SSH traffic (50k)
| \--11:1 SSH traffic (20k, isolated)
\---1:2 Other traffic (remaining)

I'm assuming that would prevent 1:2 from using any of 11:1's allotment, but does this have any other adverse effects?

Signature · 6 lines
Michael T. Babcock
CTO, FibreSpeed Ltd.     (Hosting, Security, Consultation, Database, etc)
http://www.fibrespeed.net/~mbabcock/
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/lartc/
#1 lore raw

Hi, for HTB you can do this as follows:
root (rate = 500k)
|

+-1:1 SSH leaf (rate = 50k, ceil = 500k)
|

\-1:2 other inner node (rate = 450k, ceil = 480k)

The ceil for second node will prevent it to use whole bw and 20 is always reserved for 1:1's use. See below for CBQ.

Quoted 11 lines

Lets say I wanted to allocate 50kbps to SSH traffic, but I didn't want to set it all as isolated. What if I wanted to set aside 20k of that as being isolated from other classes (either in HTB or CBQ), how would I go about this, or is it even possible? Would I have to make the normal class of 50k and then make a sub-class of 20 with the same definition but isolated? Should this work?

root
\---1:1 SSH traffic (50k)
| \--11:1 SSH traffic (20k, isolated)
\---1:2 Other traffic (remaining)

Here you has problem. You can't assign traffic to 1:1, only to 11:1 (is it another qdisc !?). Isolated class will not lend its bw bot also will not borrow ! So that 50k from 1:1 will never be reached.
I'm not sure whether it is solvable with CBQ.
devik

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/lartc/

#2 lore raw
In reply to Michael T. Babcock
Quoted 6 lines · you

Hi, for HTB you can do this as follows:
root (rate = 500k)

+-1:1 SSH leaf (rate = 50k, ceil = 500k)

\-1:2 other inner node (rate = 450k, ceil = 480k)

If you do this :

1:1 rate 500k, ceil = 500k
+-1:10 SSH leaf (rate = 20k, ceil = 500k) \-1:20 other inner node (rate = 480k, ceil = 500k)

You will end up that ssh will have at least 20k, if it's not using that bandwidth, 1:20 can use it. So ssh has a guaranteed bandwidth of 20k.

Stef

Quoted 29 lines

The ceil for second node will prevent it to use whole bw and 20 is always reserved for 1:1's use. See below for CBQ.

Quoted 7 lines

Lets say I wanted to allocate 50kbps to SSH traffic, but I didn't want to set it all as isolated. What if I wanted to set aside 20k of that as being isolated from other classes (either in HTB or CBQ), how would I go about this, or is it even possible? Would I have to make the normal class of 50k and then make a sub-class of 20 with the same definition but isolated? Should this work?

Quoted 6 lines

root
\---1:1 SSH traffic (50k)

| \--11:1 SSH traffic (20k, isolated)

\---1:2 Other traffic (remaining)

Here you has problem. You can't assign traffic to 1:1, only to 11:1 (is it another qdisc !?). Isolated class will not lend its bw bot also will not borrow ! So that 50k from 1:1 will never be reached.
I'm not sure whether it is solvable with CBQ.
devik

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/lartc/

Signature · 6 lines
[email protected]
 More QOS info : http://www.docum.org/
 Title : "Using Linux as bandwidth manager"
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/lartc/
#3 lore raw
In reply to Michael T. Babcock
Quoted 5 lines
Quoted 5 lines

Hi, for HTB you can do this as follows:
root (rate = 500k)

+-1:1 SSH leaf (rate = 50k, ceil = 500k)
\-1:2 other inner node (rate = 450k, ceil = 480k)

Quoted 8 lines

If you do this :

1:1 rate 500k, ceil = 500k
+-1:10 SSH leaf (rate = 20k, ceil = 500k) \-1:20 other inner node (rate = 480k, ceil = 500k)

You will end up that ssh will have at least 20k, if it's not using that bandwidth, 1:20 can use it. So ssh has a guaranteed bandwidth of 20k.

True. But not sure if relevant. Michael asked how to assign 50k for ssh but to make sure that 20 of it is not used by other classes even if it is unused (If I understood him correctly ;) devik

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/lartc/

#4 lore raw
In reply to Michael T. Babcock
Quoted 6 lines · Martin Devera
Quoted 2 lines

You will end up that ssh will have at least 20k, if it's not using that bandwidth, 1:20 can use it. So ssh has a guaranteed bandwidth of 20k.

True. But not sure if relevant. Michael asked how to assign 50k for ssh but to make sure that 20 of it is not used by other classes even if it is unused (If I understood him correctly ;)

Yes, thank-you both.

Signature · 6 lines
Michael T. Babcock
CTO, FibreSpeed Ltd.     (Hosting, Security, Consultation, Database, etc)
http://www.fibrespeed.net/~mbabcock/
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/lartc/