Skip to contentSkip to conversation

Routing with SNAT

LARTC Ti Leggett 2 participants 3 messages Feb 22, 2002 – Feb 24, 2002

lore
Share & tools
lore

Ti Leggett

author
#0 lore raw

I've been having some problems recently with regards to getting a particular configuration setup. Excuse me if this has been asked before but I couldn't think of a way to search for this type of question. What I have is this: a wireless NAP that does PPPoE, an ARM netwinder running debian, an Intel box running RedHat/Windows. I'm currently using DSL and get a static IP via PPPoE. What I want to do is this:

- I want the wireless NAP to connect to my DSL (ARM pppoe just isn't there yet).
- I want the netwinder right behind the NAP and fully open to the internet (this is achieved using the NAP's DMZ feature)
- The netwinder will run netfilter doing my packet filtering, NAT, and traffic shaping
- The netwinder will also be connected to a hub
- All machines behind the netwinder will connect to the hub and use the netwinder's NAT to gain net

Let's say my static ip is 1.2.3.4. The NAP's local address is 192.168.123.254. The netwinder's interface to the NAP (eth0) is 192.168.123.1. The netwinder's hub interface (eth1) is 192.168.1.1. The netwinder's default route is 192.168.123.254. All other machines connected to the hub are in the network 192.168.1.0/24 and have the default route 192.168.1.1. On the netwinder I use netfilter to do SNAT using the following rule:

-t nat -A POSTROUTING -s 192.168.1.0/255.255.255.0 -o eth0 -j SNAT --to 1.2.3.4

What works:

-The netwinder can see both local nets .123 and .1 as well as the outside internet
-All machines behind the netwinder get one way communication outwards. Example:

On the intel machine which has address 192.168.1.2 I try to ping 2.3.4.5 (an outside IP). I have root access on 2.3.4.5 so I put the ethernet interface into promiscuous mode and run "tcpdump -i eth0 -p icmp". On the netwinder I put eth0 into promiscuous mode and do the same. What I see is that the netwinder sees the outgoing ICMP requests with my static ip (1.2.3.4). 2.3.4.5 sees the request coming from 1.2.3.4 and sends replies. The netwinder never sees the replies. What I've gathered is that the netwinder needs to broadcast that it is the route for 1.2.3.4 so that these return packets get past the NAP and routed to the netwinder. In my searching I haven't found how to do this. Can anyone let me know how this might be achieved or let me know the proper way to get this working? Thanks!

-Ti Leggett
[email protected]

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/lartc/

#1 lore raw
Quoted 6 lines · Ti Leggett

I've been having some problems recently with regards to getting a particular configuration setup. Excuse me if this has been asked before but I couldn't think of a way to search for this type of question. What I have is this: a wireless NAP that does PPPoE, an ARM netwinder running debian, an Intel box running RedHat/Windows. I'm currently using DSL and get a static IP via PPPoE. What I want to do is this:

Ok.

Quoted 2 lines

- I want the wireless NAP to connect to my DSL (ARM pppoe just isn't there yet).

No? The stuff in the kernel seems very generic and works tremendously well.

Quoted 7 lines

- I want the netwinder right behind the NAP and fully open to the internet (this is achieved using the NAP's DMZ feature)
- The netwinder will run netfilter doing my packet filtering, NAT, and traffic shaping
- The netwinder will also be connected to a hub
- All machines behind the netwinder will connect to the hub and use the netwinder's NAT to gain net

Can people please draw a picture? It's not that hard and it makes it lots easier to see what you want. Anybody wanting to answer this question now has to draw this (mental) picture first, making the people who you want answers from do the work :-)

ARM - NAP - DSL
|
-------
x x x x

Quoted 10 lines

Let's say my static ip is 1.2.3.4. The NAP's local address is 192.168.123.254. The netwinder's interface to the NAP (eth0) is 192.168.123.1. The netwinder's hub interface (eth1) is 192.168.1.1. The netwinder's default route is 192.168.123.254. All other machines connected to the hub are in the network 192.168.1.0/24 and have the default route 192.168.1.1. On the netwinder I use netfilter to do SNAT using the following rule:

-t nat -A POSTROUTING -s 192.168.1.0/255.255.255.0 -o eth0 -j SNAT --to 1.2.3.4

        eth0
        123.1  123.254 
        ARM  -    NAP   -  DSL 
    eth1 | 1.1
         |
      -------
      x x x x
Quoted 6 lines

What works:

-The netwinder can see both local nets .123 and .1 as well as the outside internet
-All machines behind the netwinder get one way communication outwards. Example:

This is good - letting people know what does work helps :-)

Quoted 4 lines

On the intel machine which has address 192.168.1.2 I try to ping 2.3.4.5 (an outside IP). I have root access on 2.3.4.5 so I put the ethernet interface into promiscuous mode and run "tcpdump -i eth0 -p icmp". On the netwinder I put eth0 into promiscuous mode and do the same. What I

Quoted 8 lines

see is that the netwinder sees the outgoing ICMP requests with my static ip (1.2.3.4). 2.3.4.5 sees the request coming from 1.2.3.4 and sends replies. The netwinder never sees the replies. What I've gathered is that the netwinder needs to broadcast that it is the route for 1.2.3.4 so that these return packets get past the NAP and routed to the netwinder. In my searching I haven't found how to do this. Can anyone let me know how this might be achieved or let me know the proper way to get this working? Thanks!

What you did is invent an IP address :-) Your ISP shouldn't even let a packet with source 1.2.3.4 go out, unless that IP address is *yours*.

In this case, you should change 1.2.3.4 to an address that is routed to you, or ask your ISP to route one to you.

To see what I mean, traceroute to 1.2.3.4 from 2.3.4.5 and you will that packets aren't even going near you.

Good luck!

Signature · 6 lines
http://www.PowerDNS.com          Versatile DNS Software & Services
http://www.tk                              the dot in .tk
http://lartc.org           Linux Advanced Routing & Traffic Control HOWTO
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/lartc/
author
#2 lore raw
In reply to Ti Leggett
Quoted 5 lines · bert hubert
Quoted 2 lines

- I want the wireless NAP to connect to my DSL (ARM pppoe just isn't there yet).

No? The stuff in the kernel seems very generic and works tremendously well.

That is if you use a kernel mode pppoe package. rp-pppoe, the package that comes with RedHat and ARM debian, is a user space program. It has some problems because the ethernet frames are not packed properly for ARM as well as a few other things. I tried a kernel mode package but it was meant for older (read 2.2 kernels) and used a deprecated call somewhere. I tried about 5 different packages all with varying degrees of not working. :)

Quoted 14 lines
Quoted 7 lines

- I want the netwinder right behind the NAP and fully open to the internet (this is achieved using the NAP's DMZ feature)
- The netwinder will run netfilter doing my packet filtering, NAT, and traffic shaping
- The netwinder will also be connected to a hub
- All machines behind the netwinder will connect to the hub and use the netwinder's NAT to gain net

Can people please draw a picture? It's not that hard and it makes it lots easier to see what you want. Anybody wanting to answer this question now has to draw this (mental) picture first, making the people who you want answers from do the work :-)

Quoted 5 lines

ARM - NAP - DSL
|
-------
x x x x

Sorry... :)

Quoted 13 lines
Quoted 4 lines

On the intel machine which has address 192.168.1.2 I try to ping 2.3.4.5 (an outside IP). I have root access on 2.3.4.5 so I put the ethernet interface into promiscuous mode and run "tcpdump -i eth0 -p icmp". On the netwinder I put eth0 into promiscuous mode and do the same. What I

Quoted 8 lines

see is that the netwinder sees the outgoing ICMP requests with my static ip (1.2.3.4). 2.3.4.5 sees the request coming from 1.2.3.4 and sends replies. The netwinder never sees the replies. What I've gathered is that the netwinder needs to broadcast that it is the route for 1.2.3.4 so that these return packets get past the NAP and routed to the netwinder. In my searching I haven't found how to do this. Can anyone let me know how this might be achieved or let me know the proper way to get this working? Thanks!

Quoted 8 lines

What you did is invent an IP address :-) Your ISP shouldn't even let a packet with source 1.2.3.4 go out, unless that IP address is *yours*.

In this case, you should change 1.2.3.4 to an address that is routed to you, or ask your ISP to route one to you.

To see what I mean, traceroute to 1.2.3.4 from 2.3.4.5 and you will that packets aren't even going near you.

So in my case I was snat'ing the packet to contain my DSL static IP 1.2.3.4. I figured out that the problem is that the wireless NAP was doing some NATing of its own so that packets that came from 192.168.123.1 were routed properly because the NAP had knowledge of where they came from but the packets that were NATed to have the 1.2.3.4 address passed through the NAP because it didn't know how to NAT those, so when they return the NAP just dropped/accepted the packets thinking they were for it since there was none of its NAT info attached. (Man, is it confusing to talk about NAT over a NAP!). So, on my ARM machine, I just masqueraded the packets so that they all appeared to be coming from the ARM machine so the wireless NAP would then route everyting back through the ARM on return. Basically, two levels of NAT. Thanks and sorry for not trying this originally.

-Ti

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/lartc/