Skip to contentSkip to conversation

Src IP for outgoing packet with multiple defaults routes

LARTC Andrés Grińó Brandt 3 participants 3 messages Mar 7, 2002

lore
Share & tools
lore
#0 lore raw

Hi:

Abstract: Linux connected to two different ISP. Outgoing packets seems to peek randomly it's source IP address, without regards to the router choosen.

Test bed:
1. Linux Red Hat 7.2 (fw1) with kernel 2.4.7-10, no patches, all netfilter and adv. routing options on.
2. One "internet" ethernet card that connect to a switch. The switch connect the two routers also.
3. Linux have two IP: 200.72.44.226 and 200.27.214.226.
4. ip route list show:
200.72.44.224/27 dev eth0 scope link
200.27.214.224/29 dev eth0 proto kernel scope link src 200.27.214.226
default equalize

           nexthop via 200.27.214.225 dev eth0 weight 1
           nexthop via 200.72.44.225  dev eth0 weight 3

6. No MASQ, no SNAT, no DNAT for packets locally generated.
6. Ethercap running in eth0.
5. Another Linux (ws1) also running ethercap over the wire between router 200.27.214.225 and the switch (via a hub). This machine have address 200.27.214.227.

What I see, after running ethercap at the same time (and for the same period) on both machines:
1. Ethercap on fw1 capture ~4.500 packets, on sw1 capture ~1.900 packets.
2. On sw1 ethercap show me only packets routed thru router 200.27.214.225. I check the destination mac address, and it definitly router 200.27.214.225.
3. But on sw1, I see outgoing packets having both source IP 200.27.214.226 and 200.72.44.226.

This is wrong. Packets with source IP 200.72.44.226 must not reach router 200.27.214.226. AFIK, an outgoing packet must have a source address in the same subnet that the router being used.

Ideas?

Andrés Griñó Brandt
Santiago, Chile
http://galeria.porsiempre.cl [Fotos de viajes, familia, club, etc.]
http://club.porsiempre.cl [Sitio del Club Buceo Aventura]
http://buceo.porsiempre.cl [Página Personal]

------------------------------
http://jawmail.sourceforge.net

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#1 lore raw

Hello,

Quoted 3 lines · On Thu, 7 Mar 2002, =?ISO-8859-2?Q?Andrés Griñó Brandt?= wrote:

Hi:

Abstract: Linux connected to two different ISP. Outgoing packets seems to peek randomly it's source IP address, without regards to the router choosen.

Not possible with plain kernel, check this URL:

http://www.linuxvirtualserver.org/~julian/#routes

after patching nexthops with same outdevs are supported

Quoted 4 lines
           nexthop via 200.27.214.225 dev eth0 weight 1
           nexthop via 200.72.44.225  dev eth0 weight 3

This is wrong. Packets with source IP 200.72.44.226 must not reach router 200.27.214.226. AFIK, an outgoing packet must have a source address in the same subnet that the router being used.

To be honest, NAT in current kernels does not work correctly
with multipath routes, even if you are using different outdevs in all nexthops. Read the docs mentioned above.

Quoted 4 lines

Ideas?

Andrés Griñó Brandt
Santiago, Chile

Regards

--
Julian Anastasov <[email protected]>

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#2 lore raw
In reply to Andrés Grińó Brandt
Quoted 24 lines · Andr?s Gri?? Brandt

Hi:

Abstract: Linux connected to two different ISP. Outgoing packets seems to peek randomly it's source IP address, without regards to the router choosen.

Test bed:
1. Linux Red Hat 7.2 (fw1) with kernel 2.4.7-10, no patches, all netfilter and adv. routing options on.
2. One "internet" ethernet card that connect to a switch. The switch connect the two routers also.
3. Linux have two IP: 200.72.44.226 and 200.27.214.226.
4. ip route list show:

   200.72.44.224/27 dev eth0 scope link
   200.27.214.224/29 dev eth0 proto kernel scope link src 200.27.214.226
   default equalize 
           nexthop via 200.27.214.225 dev eth0 weight 1
           nexthop via 200.72.44.225  dev eth0 weight 3

6. No MASQ, no SNAT, no DNAT for packets locally generated.
6. Ethercap running in eth0.
5. Another Linux (ws1) also running ethercap over the wire between router 200.27.214.225 and the switch (via a hub). This machine have address 200.27.214.227.

What I see, after running ethercap at the same time (and for the same period) on both machines:
1. Ethercap on fw1 capture ~4.500 packets, on sw1 capture ~1.900 packets.
2. On sw1 ethercap show me only packets routed thru router 200.27.214.225. I check the destination mac address, and it definitly router 200.27.214.225.
3. But on sw1, I see outgoing packets having both source IP 200.27.214.226 and 200.72.44.226.

Quoted 3 lines

This is wrong. Packets with source IP 200.72.44.226 must not reach router 200.27.214.226. AFIK, an outgoing packet must have a source address in the same subnet that the router being used.

Only if you force it to be that way. You told Linux 'I have 2 default nexthops, and I want 25% of connections to go to 200.27.214.225, 75% to 200.72.44.225' and that is what happened, more or less.

If you want to be more specific, create policy rules enforcing your subnet preferences.

Regards,

bert

Signature · 6 lines
http://www.PowerDNS.com          Versatile DNS Software & Services
http://www.tk                              the dot in .tk
http://lartc.org           Linux Advanced Routing & Traffic Control HOWTO
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/