New User
Hello,
I am a new user of iproute tool and would like some help to start some experiments !!!
My computer run linux Debian with 2.2.19 kernel and iproute package
I have 2 routers with package queue an shapping by diffserv and rsvp
For now I woul like to install iproute2 + tc in my machine
I have some daults about that:
Can I use the original Debian Package for queue implamantation ?
With iproute 2 +tc I have to recompile the kernel ? Whats the best version to do that ?
What kind of experiments I can do ?
Could I use the linux like a router with QoS implementation ?
I am a kkind of new user of these tools, so I have a lot of questions
Thank you a lot
Giuliano
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
Quoted 1 line · Giuliano Cardozo Medalha
Hello,
Hi
Quoted 2 lines
I am a new user of iproute tool and would like some help to start some experiments !!!
Welcome to the club.
Quoted 1 line
My computer run linux Debian with 2.2.19 kernel and iproute package
I'm also running Debian. But I use kernel 2.4.17.
Quoted 1 line
I have 2 routers with package queue an shapping by diffserv and rsvp
Congratulations.
Quoted 1 line
For now I woul like to install iproute2 + tc in my machine
apt-get install iproute2
Quoted 2 lines
I have some daults about that:
Can I use the original Debian Package for queue implamantation ?
Yes
Quoted 2 lines
With iproute 2 +tc I have to recompile the kernel ? Whats the best version to do that ?
There is an excellent kernel-howto.
Quoted 1 line
What kind of experiments I can do ?
A lot.
Quoted 1 line
Could I use the linux like a router with QoS implementation ?
Yes
Quoted 2 lines
I am a kkind of new user of these tools, so I have a lot of questions Thank you a lot
np
Stef
Signature · 7 lines
[email protected] "Using Linux as bandwidth manager" http://www.docum.org/ #lartc @ irc.openprojects.net _______________________________________________ LARTC mailing list / [email protected] http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
[LARTC] new user
In reply to Giuliano Cardozo MedalhaHi,
i have 200 cleint a building network is cat5 cable and switches i want limiting user
can i do with LARTC?
Ismet Sonmez
Bsy Bilgi Sistemleri
Tel : 0090 224 255 77 47
Fax : 0090 224 254 89 24
Mail : [email protected]
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
Re: [LARTC] new user
In reply to Giuliano Cardozo MedalhaYes
its possible
Please look following URL's
1. www.lartc.org
2. www.docum.org
3. www.apconnections.net
hare
----- Original Message -----
From: "Ismet Sonmez" <[email protected]>
To: <[email protected]>
Sent: Tuesday, May 13, 2003 11:46 AM
Subject: [LARTC] new user
Quoted 13 lines
Hi,
i have 200 cleint a building network is cat5 cable and switches i want limiting user
can i do with LARTC?Ismet Sonmez
Bsy Bilgi Sistemleri
Tel : 0090 224 255 77 47
Fax : 0090 224 254 89 24
Mail : [email protected]
Quoted 4 lines
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
Re: [LARTC] new user
In reply to Giuliano Cardozo MedalhaQuoted 5 lines · Ismet Sonmez
Hi,
i have 200 cleint a building network is cat5 cable and switches i want limiting user
can i do with LARTC?
Yes.
Stef
Signature · 8 lines
[email protected] "Using Linux as bandwidth manager" http://www.docum.org/ #lartc @ irc.oftc.net _______________________________________________ LARTC mailing list / [email protected] http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
[LARTC] new user
In reply to Giuliano Cardozo MedalhaOk.it is possible.
i have 200 client but not in one network. 1 client 1 network for security.
exam.
7.cleint 10.client cant connect p2p. all cleint bandwidth 128 kbps
-------client1 10.1.1.1/24
|
internet<----->router<---->switch----client2 10.1.2.1/24
| |
| ------client3 10.1.3.1/24
|
|---switch ....
|
|---switch<---->client200 10.1.200.1/24client1 not connect client200
router eth1 ip 10.1.(1...200).254/24
:)
is it possible?
-----Original Message-----
From: Stef Coene [mailto:[email protected]]
Sent: Tuesday, May 13, 2003 8:06 PM
To: [email protected]; [email protected]
Subject: Re: [LARTC] new user
Quoted 5 lines · Ismet Sonmez
Hi,
i have 200 cleint a building network is cat5 cable and switches i want limiting user
can i do with LARTC?
Yes.
Stef
Signature · 11 lines
[email protected] "Using Linux as bandwidth manager" http://www.docum.org/ #lartc @ irc.oftc.net _______________________________________________ LARTC mailing list / [email protected] http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
RE: [LARTC] new user
In reply to Giuliano Cardozo Medalhahi,
eth0 internet
eth1 local
i want 200 ip on eth1
10.1.1.254/24 router 10.1.1.1/24 client1 10.1.2.254/24 router 10.1.2.1/24 client2 .
.
10.1.200.254/24 router 10.1.200.1/24 client200 dummynet
it is possible in LARTC?
-----Original Message-----
From: hare ram [mailto:[email protected]]
Sent: Wednesday, May 14, 2003 5:44 PM
To: [email protected]
Subject: Re: [LARTC] new user
your Question really confusing
what you want to achive
hare
----- Original Message -----
From: "Ismet Sonmez" <[email protected]>
To: <[email protected]>
Sent: Wednesday, May 14, 2003 12:27 PM
Subject: [LARTC] new user
Quoted 51 lines
Ok.it is possible.
i have 200 client but not in one network. 1 client 1 network for security.
exam.
7.cleint 10.client cant connect p2p. all cleint bandwidth 128 kbps-------client1 10.1.1.1/24 | internet<----->router<---->switch----client2 10.1.2.1/24 | | | ------client3 10.1.3.1/24 | |---switch .... | |---switch<---->client200 10.1.200.1/24client1 not connect client200
router eth1 ip 10.1.(1...200).254/24
:)
is it possible?-----Original Message-----
From: Stef Coene [mailto:[email protected]]
Sent: Tuesday, May 13, 2003 8:06 PM
To: [email protected]; [email protected]
Subject: Re: [LARTC] new userQuoted 5 lines · Ismet Sonmez
Hi,
i have 200 cleint a building network is cat5 cable and switches i want limiting user
can i do with LARTC?Yes.
Stef
--
[email protected]
"Using Linux as bandwidth manager"
http://www.docum.org/
#lartc @ irc.oftc.net
Quoted 4 lines
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
Re: [LARTC] new user
In reply to Giuliano Cardozo MedalhaQuoted 11 lines · Ismet Sonmez
hi,
eth0 internet
eth1 local
i want 200 ip on eth1
10.1.1.254/24 router 10.1.1.1/24 client1
10.1.2.254/24 router 10.1.2.1/24 client2
.
.
10.1.200.254/24 router 10.1.200.1/24 client200
dummynet
Quoted 1 line
it is possible in LARTC?
This question is not easy to answer because it's not clear what you want to do. But as fas I understand, it's possible.
Stef
Signature · 8 lines
[email protected] "Using Linux as bandwidth manager" http://www.docum.org/ #lartc @ irc.oftc.net _______________________________________________ LARTC mailing list / [email protected] http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
RE: [LARTC] new user
In reply to Giuliano Cardozo MedalhaIsmet,
As you may have noticed we don't really understand exactly what you wish to do. We understand that you have a number of "client" networks behind your router, and that you wish to use linux (LARTC), but we are not sure about the nature of your question.
: it is possible in LARTC?
Quite probably. I understand that there may be a linguistic barrier for you in communicating your question to the list, but we need to know more in order to engage your question. So please ask better questions in the future. With that said, here are some answers to the questions I thought you were asking:
Are you asking
1. if you can limit bandwidth for each client?
Yes. You'll want to learn about HTB. You will probably wish to create a top-level class to limit the total bandwidth to the available bandwidth for all of your clients, and then create child classes alloting 128k for each client, e.g.,
1:1 (77mbit) +--------+ 1:1001 (128kbit)
+--------+ 1:1002 (128kbit)
+--------+ 1:1003 (128kbit)
...
+--------+ 1:1200 (128kbit)
Your clients will still be "fighting" over any bandwidth left in class 1:1, but at least you can limit the total bandwidth that all of them will be able to consume. You can also cap each individual class by using the rate and ceil parameters for the child classes.
There is a metric boatload of documentation on HTB by the author [1] and by Stef Coene [2].
OR
: eth0 internet
: eth1 local
: i want 200 ip on eth1
2. if you can use a single router with multiple IPs on a single ethernet interface?
Yes. You can trivially host multiple IPs on the same interface by making use of the "ip address add" command. I have not completed writing my documentation [3] and examples for this command, but the ip-cref manual [4] which comes with the iproute2 package will provide the necessary clues.
In short, the machine can host many IPs on a single interface, and according to the rules for source address selection [5], should even generate ICMP messages from the correct IPs for your client networks.
OR
: > client1 not connect client200
3. if you can prevent the different client networks from communicating with each other?
Yes. You can do so by using iptables. I would suggest the iptables tutorial [6] for an introduction to the capabilities of packet filtering with kernel 2.4 and iptables.
You can also prevent different client networks from connecting to each other by using clever policy routing. See a discussion between me and Tomas Bonnedahl from earlier this year [7]. I would suggest using policy routing in addition to (not as a replacement for) correctly configured packet filters (see next answer).
OR
: > 7.client 10.client cant connect p2p.
4. if you can configure different packet filters for each client?
Yes. You can do so by using iptables. I would suggest the iptables tutorial [6] for an introduction to the capabilities of packet filtering with kernel 2.4 and iptables.
There are a large number of tools for automating the writing of packet filters. These tools can be found on freshmeat.net [8]. I would suggest choosing one of these after you understand how iptables can help you solve your problem.
So, in short, Ismet, linux-2.4 can probably do what you want. Please feel free to ask more specific questions after you have familiarized yourself with the wealth of options.
-Martin
[1] http://luxik.cdi.cz/~devik/qos/htb/ [2] http://www.docum.org/ [3] http://linux-ip.net/html/tools-ip-address.html [4] http://linux-ip.net/gl/ip-cref/node22.html [5] http://linux-ip.net/html/routing-saddr-selection.html http://linux-ip.net/gl/ip-cref/node155.html [6] http://iptables-tutorial.frozentux.net/ [7] http://mailman.ds9a.nl/pipermail/lartc/2003q1/007174.html [8] http://freshmeat.net/search/?q=iptables§ion=projects&x=0&y=0
Signature · 5 lines
Martin A. Brown --- SecurePipe, Inc. --- [email protected] _______________________________________________ LARTC mailing list / [email protected] http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
RE: [LARTC] new user
In reply to Giuliano Cardozo MedalhaHi Martin,
so sorry my english.i am only read but dont write and talk.
1. if you can limit bandwidth for each client? YES
2. if you can use a single router with multiple IPs on a single ethernet interface? YES
3.if you can prevent the different client networks from communicating
with each other? YES
ok.understand all.
-----Original Message-----
From: Martin A. Brown [mailto:[email protected]]
Sent: Wednesday, May 14, 2003 9:23 PM
To: Ismet Sonmez
Cc: [email protected]
Subject: RE: [LARTC] new user
Ismet,
As you may have noticed we don't really understand exactly what you wish to do. We understand that you have a number of "client" networks behind your router, and that you wish to use linux (LARTC), but we are not sure about the nature of your question.
: it is possible in LARTC?
Quite probably. I understand that there may be a linguistic barrier for you in communicating your question to the list, but we need to know more in order to engage your question. So please ask better questions in the future. With that said, here are some answers to the questions I thought you were asking:
Are you asking
1. if you can limit bandwidth for each client?
Yes. You'll want to learn about HTB. You will probably wish to create a top-level class to limit the total bandwidth to the available bandwidth for all of your clients, and then create child classes alloting 128k for each client, e.g.,
1:1 (77mbit) +--------+ 1:1001 (128kbit)
+--------+ 1:1002 (128kbit)
+--------+ 1:1003 (128kbit)
...
+--------+ 1:1200 (128kbit)
Your clients will still be "fighting" over any bandwidth left in class 1:1, but at least you can limit the total bandwidth that all of them will be able to consume. You can also cap each individual class by using the rate and ceil parameters for the child classes.
There is a metric boatload of documentation on HTB by the author [1] and by Stef Coene [2].
OR
: eth0 internet
: eth1 local
: i want 200 ip on eth1
2. if you can use a single router with multiple IPs on a single ethernet interface?
Yes. You can trivially host multiple IPs on the same interface by making use of the "ip address add" command. I have not completed writing my documentation [3] and examples for this command, but the ip-cref manual [4] which comes with the iproute2 package will provide the necessary clues.
In short, the machine can host many IPs on a single interface, and according to the rules for source address selection [5], should even generate ICMP messages from the correct IPs for your client networks.
OR
: > client1 not connect client200
3. if you can prevent the different client networks from communicating with each other?
Yes. You can do so by using iptables. I would suggest the iptables tutorial [6] for an introduction to the capabilities of packet filtering with kernel 2.4 and iptables.
You can also prevent different client networks from connecting to each other by using clever policy routing. See a discussion between me and Tomas Bonnedahl from earlier this year [7]. I would suggest using policy routing in addition to (not as a replacement for) correctly configured packet filters (see next answer).
OR
: > 7.client 10.client cant connect p2p.
4. if you can configure different packet filters for each client?
Yes. You can do so by using iptables. I would suggest the iptables tutorial [6] for an introduction to the capabilities of packet filtering with kernel 2.4 and iptables.
There are a large number of tools for automating the writing of packet filters. These tools can be found on freshmeat.net [8]. I would suggest choosing one of these after you understand how iptables can help you solve your problem.
So, in short, Ismet, linux-2.4 can probably do what you want. Please feel free to ask more specific questions after you have familiarized yourself with the wealth of options.
-Martin
[1] http://luxik.cdi.cz/~devik/qos/htb/ [2] http://www.docum.org/ [3] http://linux-ip.net/html/tools-ip-address.html [4] http://linux-ip.net/gl/ip-cref/node22.html [5] http://linux-ip.net/html/routing-saddr-selection.html http://linux-ip.net/gl/ip-cref/node155.html [6] http://iptables-tutorial.frozentux.net/ [7] http://mailman.ds9a.nl/pipermail/lartc/2003q1/007174.html [8] http://freshmeat.net/search/?q=iptables§ion=projects&x=0&y=0
Signature · 8 lines
Martin A. Brown --- SecurePipe, Inc. --- [email protected] _______________________________________________ LARTC mailing list / [email protected] http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
[LARTC] new user
In reply to Giuliano Cardozo Medalhahi, everybody
i'm razvan
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/